TI INA166UA

INA166
INA
166
www.ti.com
Low-Noise, Low-Distortion, G = 2000
INSTRUMENTATION AMPLIFIER
APPLICATIONS
FEATURES
●
●
●
●
●
●
●
LOW NOISE: 1.3nV/√Hz at 1kHz
LOW THD+N: 0.09% at 1kHz
WIDE BANDWIDTH: 450kHz
WIDE SUPPLY RANGE: ±4.5V to ±18V
HIGH CMR: > 100dB
GAIN SET WITH EXTERNAL RESISTOR
SO-14 SURFACE-MOUNT PACKAGE
● MOVING-COIL TRANSDUCER AMPLIFIERS
● DIFFERENTIAL RECEIVERS
● BRIDGE TRANSDUCER AMPLIFIERS
● MICROPHONE AND HYDROPHONE
PREAMPS
DESCRIPTION
Unique distortion cancellation circuitry reduces distortion to extremely low levels, even in high gain.
The INA166 provides near-theoretical noise performance for 200Ω source impedance. Its differential
input, low noise, and low distortion provide superior
performance as a low-level signal amplifier.
The INA166 is available in a space-saving SO-14
surface-mount package, specified for operation over
the –40°C to +85°C temperature range.
The INA166 is a very low-noise, low-distortion, monolithic instrumentation amplifier. Its current-feedback
circuitry achieves very wide bandwidth and excellent
dynamic response over a wide range of gain. It is ideal
for low-level signals such as microphones or hydrophones. Many industrial, instrumentation, and medical
applications also benefit from its low noise and wide
bandwidth.
VO1
1
INA166
–
VIN
4
3
6kΩ
60kΩ
A1
Sense
8
3kΩ
30.3Ω
A3
9
VO
3kΩ
G = 2000
12
+
VIN
5
6kΩ
A2
Ref
10
14
V O2
Copyright © 2000, Texas Instruments Incorporated
60kΩ
SBOS178
11
V+
6
V–
Printed in U.S.A. December, 2000
SPECIFICATIONS: VS = ±5V
TA = +25°C and at rated supplies, VS = ±5V, RL = 2kΩ connected to ground, G = 2000, unless otherwise noted.
INA166UA
PARAMETER
CONDITIONS
MIN
GAIN
Gain Error
Gain Temp Drift Coefficient
Nonlinearity
INPUT REFERRED NOISE
Voltage Noise
fO = 1kHz
fO = 100Hz
fO = 10Hz
Current Noise
fO = 1kHz
INPUT OFFSET VOLTAGE
Input Offset Voltage
vs Temperature
vs Power Supply
INPUT VOLTAGE RANGE
Common-Mode Voltage Range
Common-Mode Rejection
TYP
MAX
UNITS
±0.3
±10
±0.005
±1
%
ppm/°C
% of FS
RSOURCE = 0Ω
nV/√Hz
nV/√Hz
nV/√Hz
0.8
pA/√Hz
±50
±2.5
±1
VCM = VOUT = 0V
TA = TMIN to TMAX
VS = ±4.5V to ±18V
+
–
VIN
– VIN
= 0V
+
–
– VIN
= 0V
VIN
VCM = ±1V, RSRC = 0Ω
1.3
1.6
2
(V+) – 4
(V–) + 4
100
INPUT BIAS CURRENT
Initial Bias Current
vs Temperature
Initial Offset Current
vs Temperature
±250
±3
(V+) – 3
(V–) + 3
120
2.5
15
0.1
0.5
µV
µV/°C
µV/V
V
V
dB
12
1
µA
nA/°C
µA
nA/°C
INPUT IMPEDANCE
DYNAMIC RESPONSE
Bandwidth, Small Signal, –3dB
Slew Rate
THD+Noise, f = 1kHz
Settling Time, 0.1%
0.01%
Overload Recovery
OUTPUT
Voltage
Load Capacitance Stability
Short-Circuit Current
POWER SUPPLY
Rated Voltage
Voltage Range
Current, Quiescent
TEMPERATURE RANGE
Specification
Operating
Thermal Resistance, θJA
2
Differential
Common-Mode
60 2
60 2
MΩ pF
MΩ pF
5V Step
5V Step
50% Overdrive
450
15
0.09
2.5
3.5
1
kHz
V/µs
%
µs
µs
µs
(V+) – 1.8
(V–) + 1.8
1000
±60
V
V
pF
mA
RL = 2kΩ to Ground
(V+) – 2
(V–) + 2
Continuous-to-Common
±4.5
IO = 0mA
±5
±10
–40
–40
±18
±12
+85
+125
100
V
V
mA
°C
°C
°C/W
INA166
SBOS178
ELECTROSTATIC
DISCHARGE SENSITIVITY
PIN CONFIGURATION
Top View
This integrated circuit can be damaged by ESD. Burr-Brown
recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling
and installation procedures can cause damage.
VO1
1
14 VO2
NC
2
13 NC
GS1
3
12 GS2
–
VIN
4
11 V+
+
VIN
5
10 Ref
V–
6
9
VO
NC
7
8
Sense
ESD damage can range from subtle performance degradation
to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric
changes could cause the device not to meet its published
specifications.
ABSOLUTE MAXIMUM RATINGS(1)
Power Supply Voltage ....................................................................... ±18V
Signal Input Terminals, Voltage(2) .................. (V–) – 0.5V to (V+) + 0.5V
Current(2) .................................................... 10mA
Output Short-Circuit to Ground ............................................... Continuous
Operating Temperature .................................................. –55°C to +125°C
Storage Temperature ..................................................... –55°C to +125°C
Junction Temperature .................................................................... +150°C
Lead Temperature (soldering, 10s) ............................................... +300°C
SO-14
NC = No Internal Connection
NOTES: (1) Stresses above these ratings may cause permanent damage.
Exposure to absolute maximum conditions for extended periods may degrade
device reliability. These are stress ratings only, and functional operation of the
device at these or any other conditions beyond those specified is not implied.
(2) Input terminals are diode-clamped to the power-supply rails. Input signals
that can swing more than 0.5V beyond the supply rails should be current
limited to 10mA or less.
PACKAGE/ORDERING INFORMATION
PRODUCT
PACKAGE
PACKAGE
DRAWING
NUMBER
INA166UA
SO-14 Surface Mount
235
INA166UA
"
"
"
"
PACKAGE
MARKING
ORDERING
NUMBER(1)
TRANSPORT
MEDIA
INA166UA
INA166UA/2K5
Rails
Tape and Reel
NOTE: (1) Models with a slash (/) are available only in Tape and Reel in the quantities indicated (e.g., /2K5 indicates 2500 devices per reel). Ordering 2500 pieces
of “INA166UA/2K5” will get a single 2500-piece Tape and Reel.
INA166
SBOS178
3
TYPICAL PERFORMANCE CURVES
At TA = +25°C, VS = ±5V, RL = 2kΩ, CL = 50pF, G = 2000, unless otherwise noted.
GAIN vs FREQUENCY
THD+N vs FREQUENCY
70
1
VO = 5Vrms
RL = 10kΩ
60
THD+N (%)
Gain (dB)
50
40
30
0.1
20
10
0
0.01
10k
100k
1M
10M
100
1k
Frequency (Hz)
NOISE VOLTAGE (RTI) vs FREQUENCY
CURRENT NOISE SPECTRAL DENSITY
Current Noise Density (pA/√Hz)
10
1
0.1
1
10
100
1k
10k
1
10
100
10k
POWER-SUPPLY REJECTION
vs FREQUENCY
CMR vs FREQUENCY
140
140
120
120
Power-Supply Rejection (dB)
Input Referred CMR (dB)
1k
Frequency (Hz)
Frequency (Hz)
100
80
60
40
20
100
80
60
40
20
0
0
10
100
1k
10k
Frequency (Hz)
4
100k
10.0
100
Noise (RTI) (nV/√Hz)
10k
Frequency (Hz)
100k
1M
1
10
100
1k
10k
100k
1M
Frequency (Hz)
INA166
SBOS178
TYPICAL PERFORMANCE CURVES (Cont.)
At TA = +25°C, VS = ±5V, RL = 2kΩ, CL = 50pF, G = 2000, unless otherwise noted.
SMALL-SIGNAL RESPONSE
OUTPUT VOLTAGE SWING vs OUTPUT CURRENT
V+
(V+)–4
500mV/div
Output Voltage to Rail (V)
(V+)–2
(V+)–6
(V–)+6
(V–)+4
(V–)+2
V–
0
10
20
30
40
50
60
2.5µs/div
Output Current (mA)
5V/div
LARGE-SIGNAL RESPONSE
2.5µs/div
INA166
SBOS178
5
APPLICATIONS INFORMATION
Figure 1 shows the basic connections required for operation.
Power supplies should be bypassed with 0.1µF tantalum capacitors near the device pins. The output Sense (pin 8) and output
Reference (pin 10) should be low-impedance connections. Resistance of greater than 5Ω in series with these connections will
degrade the common-mode rejection of the INA166.
The input stage design used to achieve this low noise, results
in relatively high input bias current and input bias current
noise. As a result, the INA166 may not provide the best
noise performance with a source impedance greater than
10kΩ. For source impedance greater than 10kΩ, other instrumentation amplifiers may provide improved noise performance.
INPUT CONSIDERATIONS
GAIN
Gain of the INA166 is internally set for G = 2000. Input stage
(A1, A2) gain is 200 and the output stage gain (A3) is 10.
Internal resistor values are laser trimmed for accurate ratios to
achieve excellent gain accuracy and common-mode rejection,
but absolute resistor values are approximately ±20%. Nominal
resistor values are shown.
Although the INA166 is primarily intended for fixed-gain
applications, the gain can be increased by connecting a gainset resistor, RG, between pin 3 and pin 12 The nominal gain
will be:
G = 2000 +
Very low source impedance (less than 10Ω) can cause the
INA166 to oscillate. This depends on circuit layout, signal
source, and input cable characteristics. An input network
consisting of a small inductor and resistor, as shown in
Figure 2, can greatly reduce any tendency to oscillate. This
is especially useful if a variety of input sources are to be
connected to the INA166. Although not shown in other
figures, this network can be used as needed with all applications shown.
60000
RG
V+
47Ω
Accuracy of the 60000 term in this equation is approximately ±20%. The stability and temperature drift of RG
contributes to the overall gain accuracy and these effects can
be inferred from this gain equation.
4
3
11
–
VIN
1.2µH
12
5
1.2µH
+
VIN
11
8
9
INA166
VO
10
6
6
47Ω
NOISE PERFORMANCE
V–
The INA166 provides very low-noise with low-source impedance. Its 1.3nV/√Hz voltage noise delivers near-theoretical noise performance with a source impedance of 200Ω.
FIGURE 2. Input Stabilization Network.
V+
0.1µF
1
11
INA166
–
VIN
4
3
6kΩ
60kΩ
A1
Sense
V+
8
Sometimes Shown in
Simplified Form:
3kΩ
30.3Ω
RG
A3
9
VO
3kΩ
INA166
VO
G = 2000
12
+
VIN
5
6kΩ
60kΩ
A2
Ref
10
14
V–
6 0.1µF
NOTE: Gain is internally set to G = 2000.
RG can be used to increase gain. See text.
V–
FIGURE 1. Basic Circuit Connections.
6
INA166
SBOS178
OFFSET VOLTAGE TRIM
OUTPUT SENSE
A variable voltage applied to pin 10, as shown in Figure 3, can
be used to adjust the output offset voltage. A voltage applied
to pin 10 is summed with the output signal. An op amp
connected as a buffer is used to provide a low impedance at
pin 10 to assure good common-mode rejection.
An output sense terminal allows greater gain accuracy in
driving the load. By connecting the sense connection at the
load, I • R voltage loss to the load is included inside the
feedback loop. Current drive can be increased by connecting
a buffer amp inside the feedback loop, as shown in Figure 4.
V+
4
3
12
5
11
8
V+
9
INA166
VO
10
100µA
6
V–
150Ω
OPA237
10kΩ
150Ω
100µA
V–
FIGURE 3. Offset Voltage Adjustment Circuit.
+15V
Sense
4
3
12
5
±250mA
Output Drive
11
8
9
INA166
10
VO
BUF634
BW
6
BUF634 connected
for wide bandwidth.
–15V
FIGURE 4. Buffer for Increase Output Current.
INA166
SBOS178
7
PACKAGE OPTION ADDENDUM
www.ti.com
3-Oct-2003
PACKAGING INFORMATION
ORDERABLE DEVICE
STATUS(1)
PACKAGE TYPE
PACKAGE DRAWING
PINS
PACKAGE QTY
INA166UA
ACTIVE
SOIC
D
14
58
INA166UA/2K5
ACTIVE
SOIC
D
14
2500
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Amplifiers
Applications
amplifier.ti.com
Audio
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
www.ti.com/broadband
Interface
interface.ti.com
Digital Control
www.ti.com/digitalcontrol
Logic
logic.ti.com
Military
www.ti.com/military
Power Mgmt
power.ti.com
Optical Networking
www.ti.com/opticalnetwork
Microcontrollers
microcontroller.ti.com
Security
www.ti.com/security
Telephony
www.ti.com/telephony
Video & Imaging
www.ti.com/video
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright  2003, Texas Instruments Incorporated