PHILIPS LPC2210

LPC2210/2220
16/32-bit ARM microcontrollers; flashless with 64 kB,
with 10-bit ADC and external memory interface
Rev. 04 — 2 October 2007
Product data sheet
1. General description
The LPC2210/2220 microcontrollers are based on a 16/32-bit ARM7TDMI-S CPU with
real-time emulation and embedded trace support. For critical code size applications, the
alternative 16-bit Thumb mode reduces code by more than 30 % with minimal
performance penalty.
With their 144-pin package, low power consumption, various 32-bit timers, 8-channel
10-bit ADC, PWM channels, and up to nine external interrupt pins these microcontrollers
are particularly suitable for industrial control, medical systems, access control and
point-of-sale. The LPC2210/2220 can provide up to 76 GPIOs depending on bus
configuration. With a wide range of serial communications interfaces, it is also very well
suited for communication gateways, protocol converters and embedded soft modems as
well as many other general-purpose applications.
2. Features
2.1 Key features
n 16/32-bit ARM7TDMI-S microcontroller in a LQFP144 and TFBGA144 package.
n 16/64 kB on-chip static RAM (LPC2210/2220).
n Serial bootloader using UART0 provides in-system download and programming
capabilities.
n EmbeddedICE-RT and Embedded Trace interfaces offer real-time debugging with the
on-chip RealMonitor software as well as high-speed real-time tracing of instruction
execution.
n Eight channel 10-bit ADC with conversion time as low as 2.44 µs.
n Two 32-bit timers (LPC2220 also external event counters) with four capture and four
compare channels, PWM unit (six outputs), Real-Time Clock (RTC), and watchdog.
n Multiple serial interfaces including two UARTs (16C550), Fast I2C-bus (400 kbit/s) and
two SPIs. On the LPC2220, a Synchronous Serial Port (SSP) with data buffers and
variable length transfers can be selected to replace one SPI.
n Vectored Interrupt Controller (VIC) with configurable priorities and vector addresses.
n Configurable external memory interface with up to four banks, each up to 16 MB and
8/16/32-bit data width.
n Up to 76 general purpose I/O pins (5 V tolerant). Up to nine edge/level sensitive
external interrupt pins available.
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
n 60/75 MHz (LPC2210/2220) maximum CPU clock available from programmable
on-chip Phase-Locked Loop (PLL) with settling time of 100 µs.
n On-chip integrated oscillator operates with external crystal in range of 1 MHz to
30 MHz and with external oscillator up to 50 MHz.
n Power saving modes include Idle and Power-down.
n Processor wake-up from Power-down mode via external interrupt.
n Individual enable/disable of peripheral functions for power optimization.
n Dual power supply:
u CPU operating voltage range of 1.65 V to 1.95 V (1.8 V ± 0.15 V).
u I/O power supply range of 3.0 V to 3.6 V (3.3 V ± 10 %) with 5 V tolerant I/O pads.
16/32-bit ARM7TDMI-S processor.
3. Ordering information
Table 1.
Ordering information
Type number
Package
Name
Description
Version
LPC2210FBD144
LQFP144
plastic low profile quad flat package; 144 leads; SOT486-1
body 20 × 20 × 1.4 mm
LPC2220FBD144
LQFP144
plastic low profile quad flat package; 144 leads; SOT486-1
body 20 × 20 × 1.4 mm
LPC2220FET144
TFBGA144
plastic thin fine-pitch ball grid array package;
144 balls; body 12 × 12 × 0.8 mm
SOT569-1
LPC2220FET144/G
TFBGA144
plastic thin fine-pitch ball grid array package;
144 balls; body 12 × 12 × 0.8 mm
SOT569-1
3.1 Ordering options
Table 2.
Ordering options
Type number
RAM
Temperature range
LPC2210FBD144
16 kB
−40 °C to +85 °C
LPC2220FBD144
64 kB
−40 °C to +85 °C
LPC2220FET144
64 kB
−40 °C to +85 °C
LPC2220FET144/G
64 kB
−40 °C to +85 °C
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
2 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
4. Block diagram
TMS(1) TDI(1)
TRST(1) TCK(1) TDO(1)
P0[30:27],
P0[25:0]
P1[31:16],
P1[1:0]
TEST/DEBUG
INTERFACE
ARM7TDMI-S
FAST GENERAL
PURPOSE I/O
AHB BRIDGE
EMULATION TRACE
MODULE
LPC2210
LPC2220
XTAL2
XTAL1 RESET
PLL
system
clock
VECTORED
INTERRUPT
CONTROLLER
AMBA AHB
(Advanced High-performance Bus)
ARM7 local bus
INTERNAL
SRAM
CONTROLLER
16/64 kB
SRAM
SYSTEM
FUNCTIONS
AHB
DECODER
AHB TO APB
BRIDGE
APB
DIVIDER
CS3 to CS0(2)
A23 to A0(2)
BLS[3:0](2)
OE, WE(2)
D31 to D0(2)
EXTERNAL MEMORY
CONTROLLER
APB (advanced
peripheral bus)
EXTERNAL
INTERRUPTS
I2C SERIAL
INTERFACE
4 × CAP0
4 × CAP1
4 × MAT0
4 × MAT1
CAPTURE/
COMPARE
TIMER 0/TIMER 1
SPI AND SSP
SERIAL INTERFACES
0 AND 1
AIN7 to AIN0
A/D CONVERTER
UART0/UART1
GENERAL
PURPOSE I/O
REAL TIME CLOCK
EINT3 to EINT0
SCL
SDA
SCK0, SCK1
MOSI0, MOSI1
MISO0, MISO1
SSEL0, SSEL1
TXD0, TXD1
RXD0, RXD1
DSR1, CTS1,
RTS, DTR
DCD1, RI1
P0[30:27], P0[25:0]
P1[31:16], P1[1:0]
P2[31:0]
P3[31:0]
PWM6 to PWM1
WATCHDOG
TIMER
PWM0
SYSTEM
CONTROL
002aaa793
(1) When test/debug interface is used, GPIO/other functions sharing these pins are not available.
(2) Shared with GPIO.
Fig 1. Block diagram
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
3 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
5. Pinning information
109
144
5.1 Pinning
1
108
LPC2210FBD144
LPC2220FBD144
72
73
37
36
002aaa794
Fig 2. Pin configuration for LQFP144
ball A1
index area
LPC2220FET144
1 2 3 4 5 6 7 8 9 10 11 12 13
A
B
C
D
E
F
G
H
J
K
L
M
N
002aab245
Transparent top view
Fig 3. Ball configuration diagram for TFBGA144
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
4 of 49
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Ball allocation
NXP Semiconductors
LPC2210_2220_4
Product data sheet
Table 3.
Row Column
3
4
5
6
7
8
9
10
11
12
13
A
P2.22/
D22
VDDA(1V8)
P1.28/
TDI
P2.21/
D21
P2.18/
D18
P2.14/
D14
P1.29/
TCK
P2.11/
D11
P2.10/
D10
P2.7/D7
VDD(3V3)
VDD(1V8)
P2.4/D4
B
VDD(3V3)
P1.27/
TDO
XTAL2
VSSA(PLL)
P2.19/
D19
P2.15/
D15
P2.12/
D12
P0.20/
MAT1.3/
SSEL1/
EINT3
VDD(3V3)
P2.6/D6
VSS
P2.3/D3
VSS
C
P0.21/
PWM5/
CAP1.3
VSS
XTAL1
VSSA
RESET
P2.16/
D16
P2.13/
D13
P0.19/
MAT1.2/
MOSI1/
CAP1.2
P2.9/D9
P2.5/D5
P2.2/D2
P2.1/D1
VDD(3V3)
D
P0.24
P1.19/
TRACEP
KT3
P0.23
P0.22/
CAP0.0/
MAT0.0
P2.20/
D20
P2.17/
D17
VSS
P0.18/
CAP1.3/
MISO1/
MAT1.3
P2.8/D8
P1.30/
TMS
VSS
P1.20/
TRACES
YNC
P0.17/
CAP1.2/
SCK1/
MAT1.2
E
P2.25/
D25
P2.24/
D24
P2.23
VSS
P0.16/
EINT0/
MAT0.2/
CAP0.2
P0.15/
RI1/
EINT2
P2.0/D0
P3.30/
BLS1
F
P2.27/
D27/
BOOT1
P1.18/
TRACEP
KT2
VDDA(3V3)
P2.26/
D26/
BOOT0
P3.31/
BLS0
P1.21/
VDD(3V3)
PIPESTAT
0
VSS
G
P2.29/
D29
P2.28/
D28
P2.30/
P2.31/
D30/AIN4 D31/AIN5
P0.14/
DCD1/
EINT1
P1.0/CS0
P1.1/OE
H
P0.25
n.c.
P0.27/
AIN0/
CAP0.1/
MAT0.1
P1.17/
TRACEP
KT1
P0.13/
DTR1/
MAT1.1
P1.22/
P3.2/A2
PIPESTAT
1
P3.1/A1
J
P0.28/
AIN1/
CAP0.2/
MAT0.2
VSS
P3.29/
BLS2/
AIN6
P3.28/
BLS3/
AIN7
P3.3/A3
P1.23/
P0.11/
PIPESTAT CTS1/
2
CAP1.1
P0.12/
DSR1/
MAT1.0
K
P3.27/WE P3.26/
CS1
VDD(3V3)
P3.22/
A22
VDD(3V3)
P0.10/
RTS1/
CAP1.0
P3.4/A4
P3.20/
A20
P0.1/
RXD0/
PWM3/
EINT0
P3.14/
A14
P1.25/
EXTIN0
P3.11/
A11
VSS
VSS
LPC2210/2220
5 of 49
© NXP B.V. 2007. All rights reserved.
2
16/32-bit ARM microcontrollers with external memory interface
Rev. 04 — 2 October 2007
1
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxx x x x xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xx xx
xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxx xxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxx x x
xxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxx xxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxx
xxxxxxxxxxxxxxxxxxxxxxxxx xxxxxxxxxxxxxxxxxxxx xxx
Ball allocation …continued
NXP Semiconductors
LPC2210_2220_4
Product data sheet
Table 3.
Row Column
1
2
3
4
5
6
7
8
9
10
11
12
13
L
P0.29/
AIN2/
CAP0.3/
MAT0.3
P0.30/
AIN3/
EINT3/
CAP0.0
P1.16/
TRACEP
KT0
P0.0/
TXD0/
PWM1
P3.19/
A19
P0.2/
SCL/
CAP0.0
P3.15/
A15
P0.4/
SCK0/
CAP0.1
P3.12/
A12
VSS
P1.24/
TRACEC
LK
P0.8/
TXD1/
PWM4
P0.9/
RXD1/
PWM6/
EINT3
M
P3.25/
CS2
P3.24/
CS3
VDD(3V3)
P1.31/
TRST
P3.18/
A18
VDD(3V3)
P3.16/
A16
P0.3/
SDA/
MAT0.0/
EINT1
P3.13/
A13
P3.9/A9
P0.7/
SSEL0/
PWM2/
EINT2
P3.7/A7
P3.5/A5
N
VDD(1V8)
VSS
P3.23/
A23/
XCLK
P3.21/
A21
P3.17/
A17
P1.26/
RTCK
VSS
VDD(3V3)
P0.5/
MISO0/
MAT0.1
P3.10/
A10
P0.6/
MOSI0/
CAP0.2
P3.8/A8
P3.6/A6
LPC2210/2220
6 of 49
© NXP B.V. 2007. All rights reserved.
16/32-bit ARM microcontrollers with external memory interface
Rev. 04 — 2 October 2007
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
5.2 Pin description
Table 4.
Pin description
Symbol
Pin (LQFP)
Pin (TFBGA) Type
P0.0 to P0.31
I/O
Description
Port 0: Port 0 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 0 pins
depends upon the pin function selected via the Pin Connect
Block.
Pins 26 and 31 of port 0 are not available.
P0.0/TXD0/
PWM1
42[1]
L4[1]
P0.1/RXD0/
PWM3/EINT0
49[2]
P0.2/SCL/
CAP0.0
50[3]
L6[3]
P0.3/SDA/
MAT0.0/EINT1
58[3]
M8[3]
K6[2]
P0.4/SCK0/
CAP0.1
59[1]
L8[1]
P0.5/MISO0/
MAT0.1
61[1]
N9[1]
P0.6/MOSI0/
CAP0.2
68[1]
N11[1]
P0.7/SSEL0/
PWM2/EINT2
69[2]
M11[2]
P0.8/TXD1/
PWM4
75[1]
L12[1]
P0.9/RXD1/
PWM6/EINT3
76[2]
L13[2]
P0.10/RTS1/
CAP1.0
78[1]
K11[1]
P0.11/CTS1/
CAP1.1
83[1]
J12[1]
P0.12/DSR1/
MAT1.0
84[1]
J13[1]
O
TXD0 — Transmitter output for UART0.
O
PWM1 — Pulse Width Modulator output 1.
I
RXD0 — Receiver input for UART0.
O
PWM3 — Pulse Width Modulator output 3.
I
EINT0 — External interrupt 0 input
I/O
SCL — I2C-bus clock input/output. Open-drain output (for
I2C-bus compliance).
I
CAP0.0 — Capture input for Timer 0, channel 0.
I/O
SDA — I2C-bus data input/output. Open-drain output (for
I2C-bus compliance).
O
MAT0.0 — Match output for Timer 0, channel 0.
I
EINT1 — External interrupt 1 input.
I/O
SCK0 — Serial clock for SPI0. SPI clock output from master
or input to slave.
I
CAP0.1 — Capture input for Timer 0, channel 1.
I/O
MISO0 — Master In Slave OUT for SPI0. Data input to SPI
master or data output from SPI slave.
O
MAT0.1 — Match output for Timer 0, channel 1.
I/O
MOSI0 — Master Out Slave In for SPI0. Data output from SPI
master or data input to SPI slave.
I
CAP0.2 — Capture input for Timer 0, channel 2.
I
SSEL0 — Slave Select for SPI0. Selects the SPI interface as
a slave.
O
PWM2 — Pulse Width Modulator output 2.
I
EINT2 — External interrupt 2 input.
O
TXD1 — Transmitter output for UART1.
O
PWM4 — Pulse Width Modulator output 4.
I
RXD1 — Receiver input for UART1.
O
PWM6 — Pulse Width Modulator output 6.
I
EINT3 — External interrupt 3 input.
O
RTS1 — Request to Send output for UART1.
I
CAP1.0 — Capture input for Timer 1, channel 0.
I
CTS1 — Clear to Send input for UART1.
I
CAP1.1 — Capture input for Timer 1, channel 1.
I
DSR1 — Data Set Ready input for UART1.
O
MAT1.0 — Match output for Timer 1, channel 0.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
7 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Pin description …continued
Symbol
Pin (LQFP)
Pin (TFBGA) Type
Description
P0.13/DTR1/
MAT1.1
85[1]
H10[1]
O
DTR1 — Data Terminal Ready output for UART1.
O
MAT1.1 — Match output for Timer 1, channel 1.
P0.14/DCD1/
EINT1
92[2]
G10[2]
I
DCD1 — Data Carrier Detect input for UART1.
I
EINT1 — External interrupt 1 input.
Note: LOW on this pin while RESET is LOW forces on-chip
bootloader to take over control of the part after reset.
P0.15/RI1/
EINT2
99[2]
E11[2]
P0.16/EINT0/
100[2]
MAT0.2/CAP0.2
E10[2]
P0.17/CAP1.2/
SCK1/MAT1.2
101[1]
D13[1]
P0.18/CAP1.3/
MISO1/MAT1.3
121[1]
P0.19/MAT1.2/
MOSI1/CAP1.2
122[1]
D8[1]
C8[1]
I
RI1 — Ring Indicator input for UART1.
I
EINT2 — External interrupt 2 input.
I
EINT0 — External interrupt 0 input.
O
MAT0.2 — Match output for Timer 0, channel 2.
I
CAP0.2 — Capture input for Timer 0, channel 2.
I
CAP1.2 — Capture input for Timer 1, channel 2.
I/O
SCK1 — Serial Clock for SPI1/SSI/Microwire.
SPI/SSI/Microwire clock output from master or input to slave.
O
MAT1.2 — Match output for Timer 1, channel 2.
I
CAP1.3 — Capture input for Timer 1, channel 3.
I/O
MISO1 — Master In Slave Out for SPI1. Data input to SPI
master or data output from SPI slave.
O
MAT1.3 — Match output for Timer 1, channel 3.
O
MAT1.2 — Match output for Timer 1, channel 2.
I/O
MOSI1 — Master Out Slave In for SPI1. Data output from SPI
master or data input to SPI slave.
•
•
•
B8[2]
SPI interface: MOSI line.
SSI: DX/RX line (SPI1 as a master/slave).
Microwire: SO/SI line (SPI1 as a master/slave).
I
CAP1.2 — Capture input for Timer 1, channel 2.
O
MAT1.3 — Match output for Timer 1, channel 3.
I
SSEL1 — Slave Select for SPI1/Microwire. Used to select the
SPI or Microwire interface as a slave. Frame synchronization
in case of 4-wire SSI.
I
EINT3 — External interrupt 3 input.
O
PWM5 — Pulse Width Modulator output 5.
I
CAP1.3 — Capture input for Timer 1, channel 3.
I
CAP0.0 — Capture input for Timer 0, channel 0.
P0.20/MAT1.3/
SSEL1/ EINT3
123[2]
P0.21/PWM5/
CAP1.3
4[1]
P0.22/CAP0.0/
MAT0.0
5[1]
D4[1]
O
MAT0.0 — Match output for Timer 0, channel 0.
P0.23
6[1]
D3[1]
I/O
General purpose bidirectional digital port only.
P0.24
8[1]
D1[1]
I/O
General purpose bidirectional digital port only.
P0.25
21[1]
H1[1]
I/O
General purpose bidirectional digital port only.
P0.27/AIN0/
CAP0.1/MAT0.1
23[4]
H3[4]
I
AIN0 — ADC, input 0. This analog input is always connected
to its pin.
I
CAP0.1 — Capture input for Timer 0, channel 1.
O
MAT0.1 — Match output for Timer 0, channel 1.
C1[1]
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
8 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Pin description …continued
Symbol
Pin (LQFP)
P0.28/AIN1/
25[4]
CAP0.2/MAT0.2
P0.29/AIN2/
32[4]
CAP0.3/MAT0.3
P0.30/AIN3/
EINT3/CAP0.0
33[4]
Pin (TFBGA) Type
Description
J1[4]
I
AIN1 — ADC, input 1. This analog input is always connected
to its pin.
I
CAP0.2 — Capture input for Timer 0, channel 2.
L1[4]
L2[4]
P1.0 to P1.31
O
MAT0.2 — Match output for Timer 0, channel 2.
I
AIN2 — ADC, input 2. This analog input is always connected
to its pin.
I
CAP0.3 — Capture input for Timer 0, Channel 3.
O
MAT0.3 — Match output for Timer 0, channel 3.
I
AIN3 — ADC, input 3. This analog input is always connected
to its pin.
I
EINT3 — External interrupt 3 input.
I
CAP0.0 — Capture input for Timer 0, channel 0.
I/O
Port 1: Port 1 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 1 pins
depends upon the pin function selected via the Pin Connect
Block.
Pins 0 through 15 of port 1 are not available.
P1.0/CS0
91[5]
G11[5]
P1.1/OE
90[5]
G13[5]
O
OE — LOW-active Output Enable signal.
P1.16/
TRACEPKT0
34[5]
L3[5]
O
TRACEPKT0 — Trace Packet, bit 0. Standard I/O port with
internal pull-up.
P1.17/
TRACEPKT1
24[5]
H4[5]
O
TRACEPKT1 — Trace Packet, bit 1. Standard I/O port with
internal pull-up.
P1.18/
TRACEPKT2
15[5]
F2[5]
O
TRACEPKT2 — Trace Packet, bit 2. Standard I/O port with
internal pull-up.
P1.19/
TRACEPKT3
7[5]
D2[5]
O
TRACEPKT3 — Trace Packet, bit 3. Standard I/O port with
internal pull-up.
P1.20/
TRACESYNC
102[5]
D12[5]
O
TRACESYNC — Trace Synchronization. Standard I/O port
with internal pull-up.
O
CS0 — LOW-active Chip Select 0 signal.
(Bank 0 addresses range 8000 0000 to 80FF FFFF)
Note: LOW on this pin while RESET is LOW, enables pins
P1[25:16] to operate as Trace port after reset.
P1.21/
PIPESTAT0
95[5]
F11[5]
O
PIPESTAT0 — Pipeline Status, bit 0. Standard I/O port with
internal pull-up.
P1.22/
PIPESTAT1
86[5]
H11[5]
O
PIPESTAT1 — Pipeline Status, bit 1. Standard I/O port with
internal pull-up.
P1.23/
PIPESTAT2
82[5]
J11[5]
O
PIPESTAT2 — Pipeline Status, bit 2. Standard I/O port with
internal pull-up.
P1.24/
TRACECLK
70[5]
L11[5]
O
TRACECLK — Trace Clock. Standard I/O port with internal
pull-up.
P1.25/EXTIN0
60[5]
K8[5]
I
EXTIN0 — External Trigger Input. Standard I/O with internal
pull-up.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
9 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Pin description …continued
Symbol
Pin (LQFP)
Pin (TFBGA) Type
Description
P1.26/RTCK
52[5]
N6[5]
RTCK — Returned Test Clock output. Extra signal added to
the JTAG port. Assists debugger synchronization when
processor frequency varies. Bidirectional pin with internal
pull-up.
I/O
Note: LOW on this pin while RESET is LOW, enables pins
P1[31:26] to operate as Debug port after reset.
P1.27/TDO
144[5]
B2[5]
O
TDO — Test Data out for JTAG interface.
P1.28/TDI
140[5]
A3[5]
I
TDI — Test Data in for JTAG interface.
P1.29/TCK
126[5]
A7[5]
I
TCK — Test Clock for JTAG interface.
P1.30/TMS
113[5]
D10[5]
I
TMS — Test Mode Select for JTAG interface.
P1.31/TRST
43[5]
M4[5]
I
TRST — Test Reset for JTAG interface.
I/O
Port 2 — Port 2 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 2 pins
depends upon the pin function selected via the Pin Connect
Block.
P2.0 to P2.31
P2.0/D0
98[5]
E12[5]
I/O
D0 — External memory data line 0.
P2.1/D1
105[5]
C12[5]
I/O
D1 — External memory data line 1.
P2.2/D2
106[5]
C11[5]
I/O
D2 — External memory data line 2.
P2.3/D3
108[5]
B12[5]
I/O
D3 — External memory data line 3.
P2.4/D4
109[5]
A13[5]
I/O
D4 — External memory data line 4.
P2.5/D5
114[5]
C10[5]
I/O
D5 — External memory data line 5.
P2.6/D6
115[5]
B10[5]
I/O
D6 — External memory data line 6.
P2.7/D7
116[5]
A10[5]
I/O
D7 — External memory data line 7.
P2.8/D8
117[5]
D9[5]
I/O
D8 — External memory data line 8.
P2.9/D9
118[5]
C9[5]
I/O
D9 — External memory data line 9.
P2.10/D10
120[5]
A9[5]
I/O
D10 — External memory data line 10.
P2.11/D11
124[5]
A8[5]
I/O
D11 — External memory data line 11.
P2.12/D12
125[5]
B7[5]
I/O
D12 — External memory data line 12.
P2.13/D13
127[5]
C7[5]
I/O
D13 — External memory data line 13.
P2.14/D14
129[5]
A6[5]
I/O
D14 — External memory data line 14.
P2.15/D15
130[5]
B6[5]
I/O
D15 — External memory data line 15.
P2.16/D16
131[5]
C6[5]
I/O
D16 — External memory data line 16.
P2.17/D17
132[5]
D6[5]
I/O
D17 — External memory data line 17.
P2.18/D18
133[5]
A5[5]
I/O
D18 — External memory data line 18.
P2.19/D19
134[5]
B5[5]
I/O
D19 — External memory data line 19.
P2.20/D20
136[5]
D5[5]
I/O
D20 — External memory data line 20.
P2.21/D21
137[5]
A4[5]
I/O
D21 — External memory data line 21.
P2.22/D22
1[5]
A1[5]
I/O
D22 — External memory data line 22.
P2.23/D23
10[5]
E3[5]
I/O
D23 — External memory data line 23.
P2.24/D24
11[5]
E2[5]
I/O
D24 — External memory data line 24.
P2.25/D25
12[5]
E1[5]
I/O
D25 — External memory data line 25.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
10 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Pin description …continued
Symbol
Pin (LQFP)
Pin (TFBGA) Type
Description
P2.26/D26/
BOOT0
13[5]
F4[5]
I/O
D26 — External memory data line 26.
I
BOOT0 — While RESET is LOW, together with BOOT1
controls booting and internal operation. Internal pull-up
ensures HIGH state if pin is left unconnected.
P2.27/D27/
BOOT1
16[5]
I/O
D27 — External memory data line 27.
I
BOOT1 — While RESET is LOW, together with BOOT0
controls booting and internal operation. Internal pull-up
ensures HIGH state if pin is left unconnected.
F1[5]
BOOT1:0 = 00 selects 8-bit memory on CS0 for boot.
BOOT1:0 = 01 selects 16-bit memory on CS0 for boot.
BOOT1:0 = 10 selects 32-bit memory on CS0 for boot.
BOOT1:0 = 11 selects 16-bit memory on CS0 for boot.
P2.28/D28
17[5]
G2[5]
I/O
D28 — External memory data line 28.
P2.29/D29
18[5]
G1[5]
I/O
D29 — External memory data line 29.
P2.30/D30/
AIN4
19[2]
G3[2]
I/O
D30 — External memory data line 30.
I
AIN4 — ADC, input 4. This analog input is always connected
to its pin.
P2.31/D31/
AIN5
20[2]
I/O
D31 — External memory data line 31.
I
AIN5 — ADC, input 5. This analog input is always connected
to its pin.
I/O
Port 3 — Port 3 is a 32-bit bidirectional I/O port with individual
direction controls for each bit. The operation of port 3 pins
depends upon the pin function selected via the Pin Connect
Block.
G4[2]
P3.0 to P3.31
P3.0/A0
89[5]
G12[5]
O
A0 — External memory address line 0.
P3.1/A1
88[5]
H13[5]
O
A1 — External memory address line 1.
P3.2/A2
87[5]
H12[5]
O
A2 — External memory address line 2.
P3.3/A3
81[5]
J10[5]
O
A3 — External memory address line 3.
P3.4/A4
80[5]
K13[5]
O
A4 — External memory address line 4.
P3.5/A5
74[5]
M13[5]
O
A5 — External memory address line 5.
P3.6/A6
73[5]
N13[5]
O
A6 — External memory address line 6.
P3.7/A7
72[5]
M12[5]
O
A7 — External memory address line 7.
P3.8/A8
71[5]
N12[5]
O
A8 — External memory address line 8.
P3.9/A9
66[5]
M10[5]
O
A9 — External memory address line 9.
P3.10/A10
65[5]
N10[5]
O
A10 — External memory address line 10.
P3.11/A11
64[5]
K9[5]
O
A11 — External memory address line 11.
P3.12/A12
63[5]
L9[5]
O
A12 — External memory address line 12.
P3.13/A13
62[5]
M9[5]
O
A13 — External memory address line 13.
P3.14/A14
56[5]
K7[5]
O
A14 — External memory address line 14.
P3.15/A15
55[5]
L7[5]
O
A15 — External memory address line 15.
P3.16/A16
53[5]
M7[5]
O
A16 — External memory address line 16.
P3.17/A17
48[5]
N5[5]
O
A17 — External memory address line 17.
P3.18/A18
47[5]
M5[5]
O
A18 — External memory address line 18.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
11 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Pin description …continued
Symbol
Pin (LQFP)
Pin (TFBGA) Type
Description
P3.19/A19
46[5]
L5[5]
O
A19 — External memory address line 19.
P3.20/A20
45[5]
K5[5]
O
A20 — External memory address line 20.
P3.21/A21
44[5]
N4[5]
O
A21 — External memory address line 21.
P3.22/A22
41[5]
K4[5]
O
A22 — External memory address line 22.
P3.23/A23/
XCLK
40[5]
N3[5]
O
A23 — External memory address line 23.
O
XCLK — Clock output.
P3.24/CS3
36[5]
M2[5]
O
CS3 — LOW-active Chip Select 3 signal.
P3.25/CS2
35[5]
M1[5]
O
P3.26/CS1
30[5]
K2[5]
O
P3.27/WE
29[5]
K1[5]
O
WE — LOW-active Write enable signal.
P3.28/BLS3/
AIN7
28[2]
J4[2]
O
BLS3 — LOW-active Byte Lane Select signal (Bank 3).
I
AIN7 — ADC, input 7. This analog input is always connected
to its pin.
P3.29/BLS2/
AIN6
27[4]
P3.30/BLS1
97[4]
(Bank 3 addresses range 8300 0000 to 83FF FFFF)
CS2 — LOW-active Chip Select 2 signal.
(Bank 2 addresses range 8200 0000 to 82FF FFFF)
CS1 — LOW-active Chip Select 1 signal.
(Bank 1 addresses range 8100 0000 to 81FF FFFF)
J3[4]
O
BLS2 — LOW-active Byte Lane Select signal (Bank 2).
I
AIN6 — ADC, input 6. This analog input is always connected
to its pin.
E13[4]
O
BLS1 — LOW-active Byte Lane Select signal (Bank 1).
P3.31/BLS0
96[4]
F10[4]
O
BLS0 — LOW-active Byte Lane Select signal (Bank 0).
n.c.
22[5]
H2[5]
RESET
135[6]
C5[6]
I
External reset input: A LOW on this pin resets the device,
causing I/O ports and peripherals to take on their default
states, and processor execution to begin at address 0. TTL
with hysteresis, 5 V tolerant.
XTAL1
142[7]
C3[7]
I
Input to the oscillator circuit and internal clock generator
circuits.
XTAL2
141[7]
B3[7]
O
Output from the oscillator amplifier.
VSS
3, 9, 26, 38,
54, 67, 79,
93, 103, 107,
111, 128
C2, E4, J2,
N2, N7, L10,
K12, F13,
D11, B13,
B11, D7
I
Ground: 0 V reference.
VSSA
139
C4
I
Analog ground: 0 V reference. This should nominally be the
same voltage as VSS, but should be isolated to minimize noise
and error.
VSSA(PLL)
138
B4
I
PLL analog ground: 0 V reference. This should nominally be
the same voltage as VSS, but should be isolated to minimize
noise and error.
VDD(1V8)
37, 110
N1, A12
I
1.8 V core power supply: This is the power supply voltage
for internal circuitry.
Not connected. This pin MUST NOT be pulled LOW or the
device might not operate properly.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
12 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 4.
Pin description …continued
Symbol
Pin (LQFP)
Pin (TFBGA) Type
Description
VDDA(1V8)
143
A2
Analog 1.8 V core power supply: This is the power supply
voltage for internal circuitry. This should be nominally the
same voltage as VDD(1V8) but should be isolated to minimize
noise and error.
VDD(3V3)
I
2, 31, 39, 51, B1, K3, M3,
M6, N8, K10,
57, 77, 94,
104, 112, 119 F12, C13,
A11, B9
3.3 V pad power supply: This is the power supply voltage for
the I/O ports.
VDDA(3V3)
14
Analog 3.3 V pad power supply: This should be nominally
the same voltage as VDD(3V3) but should be isolated to
minimize noise and error.
F3
I
I
[1]
5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control.
[2]
5 V tolerant pad providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control. If configured for an input
function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns.
[3]
Open drain 5 V tolerant digital I/O I2C-bus 400 kHz specification compatible pad. It requires external pull-up to provide an output
functionality.
[4]
5 V tolerant pad providing digital I/O (with TTL levels and hysteresis and 10 ns slew rate control) and analog input function. If configured
for a digital input function, this pad utilizes built-in glitch filter that blocks pulses shorter than 3 ns. When configured as an ADC input,
digital section of the pad is disabled.
[5]
5 V tolerant pad with built-in pull-up resistor providing digital I/O functions with TTL levels and hysteresis and 10 ns slew rate control.
The pull-up resistor’s value ranges from 60 kΩ to 300 kΩ.
[6]
5 V tolerant pad providing digital input (with TTL levels and hysteresis) function only.
[7]
Pad provides special analog functionality.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
13 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6. Functional description
6.1 Architectural overview
The ARM7TDMI-S is a general purpose 32-bit microprocessor, which offers high
performance and very low power consumption. The ARM architecture is based on RISC
principles, and the instruction set and related decode mechanism are much simpler than
those of microprogrammed CISC. This simplicity results in a high instruction throughput
and impressive real-time interrupt response from a small and cost-effective processor
core.
Pipeline techniques are employed so that all parts of the processing and memory systems
can operate continuously. Typically, while one instruction is being executed, its successor
is being decoded, and a third instruction is being fetched from memory.
The ARM7TDMI-S processor also employs a unique architectural strategy known as
Thumb, which makes it ideally suited to high-volume applications with memory
restrictions, or applications where code density is an issue.
The key idea behind Thumb is that of a super-reduced instruction set. Essentially, the
ARM7TDMI-S processor has two instruction sets:
• The standard 32-bit ARM set.
• A 16-bit Thumb set.
The Thumb set’s 16-bit instruction length allows it to approach twice the density of
standard ARM code while retaining most of the ARM’s performance advantage over a
traditional 16-bit processor using 16-bit registers. This is possible because Thumb code
operates on the same 32-bit register set as ARM code.
Thumb code is able to provide up to 65 % of the code size of ARM, and 160 % of the
performance of an equivalent ARM processor connected to a 16-bit memory system.
6.2 On-chip SRAM
On-chip SRAM may be used for code and/or data storage. The SRAM may be accessed
as 8 bit, 16 bit, and 32 bit. The LPC2210/2220 provide 16 kB of static RAM and the
LPC2220 provides 64 kB of static RAM.
6.3 Memory map
The LPC2210/2220 memory maps incorporate several distinct regions, as shown in
Figure 4.
In addition, the CPU interrupt vectors may be re-mapped to allow them to reside in either
on-chip bootloader, external memory BANK0 or on-chip static RAM. This is described in
Section 6.20 “System control”.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
14 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
4.0 GB
0xFFFF FFFF
AHB PERIPHERALS
3.75 GB
APB PERIPHERALS
0xF000 0000
0xEFFF FFFF
0xE000 0000
0xDFFF FFFF
3.5 GB
RESERVED ADDRESS SPACE
3.0 GB
0x8400 0000
0x83FF FFFF
EXTERNAL MEMORY BANK3
EXTERNAL MEMORY BANK2
EXTERNAL MEMORY BANK1
EXTERNAL MEMORY BANK0
2.0 GB
BOOT BLOCK (RE-MAPPED FROM
ON-CHIP ROM MEMORY
0x8300 0000
0x82FF FFFF
0x8200 0000
0x81FF FFFF
0x8100 0000
0x80FF FFFF
0x8000 0000
0x7FFF FFFF
0x7FFF E000
0x7FFF DFFF
RESERVED ADDRESS SPACE
64 KBYTE ON-CHIP STATIC RAM (LPC2220)
0x4001 0000
0x4000 FFFF
0x4000 4000
0x4000 3FFF
16 KBYTE ON-CHIP STATIC RAM (LPC2210)
0x4000 0000
0x3FFF FFFF
1.0 GB
RESERVED ADDRESS SPACE
0x0000 0000
0.0 GB
002aaa795
Fig 4. LPC2210/2220 memory map
6.4 Interrupt controller
The VIC accepts all of the interrupt request inputs and categorizes them as Fast Interrupt
Request (FIQ), vectored Interrupt Request (IRQ), and non-vectored IRQ as defined by
programmable settings. The programmable assignment scheme means that priorities of
interrupts from the various peripherals can be dynamically assigned and adjusted.
FIQ has the highest priority. If more than one request is assigned to FIQ, the VIC
combines the requests to produce the FIQ signal to the ARM processor. The fastest
possible FIQ latency is achieved when only one request is classified as FIQ, because then
the FIQ service routine can simply start dealing with that device. But if more than one
request is assigned to the FIQ class, the FIQ service routine can read a word from the VIC
that identifies which FIQ source(s) is (are) requesting an interrupt.
Vectored IRQs have the middle priority. Sixteen of the interrupt requests can be assigned
to this category. Any of the interrupt requests can be assigned to any of the 16 vectored
IRQ slots, among which slot 0 has the highest priority and slot 15 has the lowest.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
15 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Non-vectored IRQs have the lowest priority.
The VIC combines the requests from all the vectored and non-vectored IRQs to produce
the IRQ signal to the ARM processor. The IRQ service routine can start by reading a
register from the VIC and jumping there. If any of the vectored IRQs are requesting, the
VIC provides the address of the highest-priority requesting IRQs service routine,
otherwise it provides the address of a default routine that is shared by all the non-vectored
IRQs. The default routine can read another VIC register to see what IRQs are active.
6.4.1 Interrupt sources
Table 5 lists the interrupt sources for each peripheral function. Each peripheral device has
one interrupt line connected to the VIC, but may have several internal interrupt flags.
Individual interrupt flags may also represent more than one interrupt source.
Table 5.
Interrupt sources
Block
Flag(s)
VIC channel #
WDT
Watchdog Interrupt (WDINT)
0
-
Reserved for software interrupts only
1
ARM Core
EmbeddedICE, DbgCommRX
2
ARM Core
EmbeddedICE, DbgCommTX
3
TIMER0
Match 0 to 3 (MR0, MR1, MR2, MR3)
4
TIMER1
Match 0 to 3 (MR0, MR1, MR2, MR3)
5
RX Line Status (RLS)
6
UART0
Transmit Holding Register empty (THRE)
RX Data Available (RDA)
Character Time-out Indicator (CTI)
UART1
RX Line Status (RLS)
7
Transmit Holding Register empty (THRE)
RX Data Available (RDA)
Character Time-out Indicator (CTI)
Modem Status Interrupt (MSI)
PWM0
Match 0 to 6 (MR0, MR1, MR2, MR3, MR4, MR5, MR6)
I2C
SI (state change)
9
SPI0
SPIF, MODF
10
SPI1 and SSP
SPIF, MODF and TXRIS, RXRIS, RTRIS, RORRIS
11
PLL
PLL Lock (PLOCK)
12
RTC
RTCCIF (Counter Increment), RTCALF (Alarm)
13
System Control
External Interrupt 0 (EINT0)
14
External Interrupt 1 (EINT1)
15
External Interrupt 2 (EINT2)
16
A/D
External Interrupt 3 (EINT3)
17
ADC
18
LPC2210_2220_4
Product data sheet
8
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
16 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.5 Pin connect block
The pin connect block allows selected pins of the microcontroller to have more than one
function. Configuration registers control the multiplexers to allow connection between the
pin and the on chip peripherals. Peripherals should be connected to the appropriate pins
prior to being activated, and prior to any related interrupt(s) being enabled. Activity of any
enabled peripheral function that is not mapped to a related pin should be considered
undefined.
The pin control module contains three registers as shown in Table 6.
Table 6.
Pin control module registers
Address
Name
Description
Access
0xE002 C000
PINSEL0
pin function select register 0
read/write
0xE002 C004
PINSEL1
pin function select register 1
read/write
0xE002 C014
PINSEL2
pin function select register 2
read/write
6.6 Pin function select register 0 (PINSEL0 - 0xE002 C000)
The PINSEL0 register controls the functions of the pins as per the settings listed in
Table 7. The direction control bit in the IODIR register is effective only when the GPIO
function is selected for a pin. For other functions, direction is controlled automatically.
Settings other than those shown in Table 7 are reserved, and should not be used
Table 7.
Pin function select register 0 (PINSEL0 - 0xE002 C000)
PINSEL0
Pin name
Value
1:0
P0.0
0
3:2
5:4
7:6
9:8
P0.1
P0.2
P0.3
P0.4
Function
Value after reset
0
GPIO Port 0.0
0
0
1
TXD (UART0)
1
0
PWM1
1
1
reserved
0
0
GPIO Port 0.1
0
1
RXD (UART0)
1
0
PWM3
1
1
EINT0
0
0
GPIO Port 0.2
0
1
SCL
(I2C-bus)
1
0
Capture 0.0 (Timer 0)
1
1
reserved
0
0
GPIO Port 0.3
0
1
SDA
(I2C-bus)
1
0
Match 0.0 (Timer 0)
1
1
EINT1
0
0
GPIO Port 0.4
0
1
SCK (SPI0)
1
0
Capture 0.1 (Timer 0)
1
1
reserved
LPC2210_2220_4
Product data sheet
0
0
0
0
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
17 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 7.
Pin function select register 0 (PINSEL0 - 0xE002 C000) …continued
PINSEL0
Pin name
Value
Function
Value after reset
11:10
P0.5
0
0
GPIO Port 0.5
0
0
1
MISO (SPI0)
1
0
Match 0.1 (Timer 0)
1
1
reserved
0
0
GPIO Port 0.6
0
1
MOSI (SPI0)
1
0
Capture 0.2 (Timer 0)
1
1
reserved
0
0
GPIO Port 0.7
0
1
SSEL (SPI0)
1
0
PWM2
1
1
EINT2
0
0
GPIO Port 0.8
0
1
TXD UART1
1
0
PWM4
1
1
reserved
0
0
GPIO Port 0.9
0
1
RXD (UART1)
1
0
PWM6
1
1
EINT3
0
0
GPIO Port 0.10
0
1
RTS (UART1)
1
0
Capture 1.0 (Timer 1)
1
1
reserved
0
0
GPIO Port 0.11
0
1
CTS (UART1)
1
0
Capture 1.1 (Timer 1)
1
1
reserved
0
0
GPIO Port 0.12
0
1
DSR (UART1)
1
0
Match 1.0 (Timer 1)
1
1
reserved
0
0
GPIO Port 0.13
0
1
DTR (UART1)
1
0
Match 1.1 (Timer 1)
1
1
reserved
0
0
GPIO Port 0.14
0
1
DCD (UART1)
1
0
EINT1
1
1
reserved
13:12
15:14
17:16
19:18
21:20
23:22
25:24
27:26
29:28
P0.6
P0.7
P0.8
P0.9
P0.10
P0.11
P0.12
P0.13
P0.14
LPC2210_2220_4
Product data sheet
0
0
0
0
0
0
0
0
0
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
18 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 7.
Pin function select register 0 (PINSEL0 - 0xE002 C000) …continued
PINSEL0
Pin name
Value
Function
Value after reset
31:30
P0.15
0
0
GPIO Port 0.15
0
0
1
RI (UART1)
1
0
EINT2
1
1
reserved
6.7 Pin function select register 1 (PINSEL1 - 0xE002 C004)
The PINSEL1 register controls the functions of the pins as per the settings listed in
Table 8. The direction control bit in the IODIR register is effective only when the GPIO
function is selected for a pin. For other functions direction is controlled automatically.
Settings other than those shown in the Table 8 are reserved, and should not be used.
Table 8.
Pin function select register 1 (PINSEL1 - 0xE002 C004)
PINSEL1
Pin name
1:0
P0.16
3:2
5:4
7:6
9:8
11:10
13:12
P0.17
P0.18
P0.19
P0.20
P0.21
P0.22
Value
Function
Value after reset
0
0
0
GPIO Port 0.16
0
1
EINT0
1
0
Match 0.2 (Timer 0)
1
1
Capture 0.2 (Timer 0)
0
0
GPIO Port 0.17
0
1
Capture 1.2 (Timer 1)
1
0
SCK (SPI1)
1
1
Match 1.2 (Timer 1)
0
0
GPIO Port 0.18
0
1
Capture 1.3 (Timer 1)
1
0
MISO (SPI1)
1
1
Match 1.3 (Timer 1)
0
0
GPIO Port 0.19
0
1
Match 1.2 (Timer 1)
1
0
MOSI (SPI1)
1
1
Capture 1.2 (Timer 1)
0
0
GPIO Port 0.20
0
1
Match 1.3 (Timer 1)
1
0
SSEL (SPI1)
1
1
EINT3
0
0
GPIO Port 0.21
0
1
PWM5
1
0
reserved
1
1
Capture 1.3 (Timer 1)
0
0
GPIO Port 0.22
0
1
reserved
1
0
Capture 0.0 (Timer 0)
1
1
Match 0.0 (Timer 0)
LPC2210_2220_4
Product data sheet
0
0
0
0
0
0
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
19 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 8.
Pin function select register 1 (PINSEL1 - 0xE002 C004) …continued
PINSEL1
Pin name
Value
Function
Value after reset
15:14
P0.23
0
0
GPIO Port 0.23
0
0
1
reserved
1
0
reserved
1
1
reserved
0
0
GPIO Port 0.24
0
1
reserved
1
0
reserved
1
1
reserved
0
0
GPIO Port 0.25
0
1
reserved
1
0
reserved
1
1
reserved
0
0
reserved
0
1
reserved
1
0
reserved
1
1
reserved
0
0
GPIO Port 0.27
0
1
AIN0 (A/D input 0)
1
0
Capture 0.1 (Timer 0)
1
1
Match 0.1 (Timer 0)
0
0
GPIO Port 0.28
0
1
AIN1 (A/D input 1)
1
0
Capture 0.2 (Timer 0)
1
1
Match 0.2 (Timer 0)
0
0
GPIO Port 0.29
0
1
AIN2 (A/D input 2)
1
0
Capture 0.3 (Timer 0)
1
1
Match 0.3 (Timer 0)
0
0
GPIO Port 0.30
0
1
AIN3 (A/D input 0)
1
0
EINT3
1
1
Capture 0.0 (Timer 0)
0
0
reserved
0
1
reserved
1
0
reserved
1
1
reserved
17:16
19:18
21:20
23:22
25:24
27:26
29:28
31:30
P0.24
P0.25
P0.26
P0.27
P0.28
P0.29
P0.30
P0.31
LPC2210_2220_4
Product data sheet
0
0
0
1
1
1
1
0
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
20 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.8 Pin function select register 2 (PINSEL2 - 0xE002 C014)
The PINSEL2 register controls the functions of the pins as per the settings listed in
Table 9. The direction control bit in the IODIR register is effective only when the GPIO
function is selected for a pin. For other functions direction is controlled automatically.
Settings other than those shown in Table 9 are reserved, and should not be used.
Table 9.
Pin function select register 2 (PINSEL2 - 0xE002 C014)
PINSEL2 bits
Description
Reset value
1:0
reserved
-
2
When 0, pins P1[36:26] are used as GPIO pins. When 1, P1[31:26] are used as a
Debug port.
P1.26/RTCK
3
When 0, pins P1[25:16] are used as GPIO pins. When 1, P1[25:16] are used as a
Trace port.
P1.20/
TRACESYNC
Controls the use of the data bus and strobe pins:
BOOT1:0
5:4
Pins P2[7:0]
11 = P2[7:0]
0x or 10 = D7 to D0
Pin P1.0
11 = P1.0
0x or 10 = CS0
Pin P1.1
11 = P1.1
0x or 10 = OE
Pin P3.31
11 = P3.31
0x or 10 = BLS0
Pins P2[15:8]
00 or 11 = P2[15:8]
01 or 10 = D15 to D8
Pin P3.30
00 or 11 = P3.30
01 or 10 = BLS1
Pins P2[27:16]
0x or 11 = P2[27:16]
Pins P2[29:28]
0x or 11 = P2[29:28]
10 = D29, D28
Pins P2[31:30]
0x or 11 = P2[31:30] or AIN5 to
AIN4
10 = D31, D30
Pins P3[29:28]
0x or 11 = P3[29:28] or AIN7 to
AIN6
10 = BLS2, BLS3
10 = D27 to D16
6
If bits 5:4 are not 10, controls the use of pin P3.29: 0 enables P3.29, 1 enables
AIN6.
1
7
If bits 5:4 are not 10, controls the use of pin P3.28: 0 enables P3.28, 1 enables
AIN7.
1
8
Controls the use of pin P3.27: 0 enables P3.27, 1 enables WE.
0
10:9
reserved
-
11
Controls the use of pin P3.26: 0 enables P3.26, 1 enables CS1.
0
12
reserved
-
13
If bits 27:25 are not 111, controls the use of pin P3.23/A23/XCLK: 0 enables P3.23, 0
1 enables XCLK.
15:14
Controls the use of pin P3.25: 00 enables P3.25, 01 enables CS2, 10 and 11 are
reserved values.
00
17:16
Controls the use of pin P3.24: 00 enables P3.24, 01 enables CS3, 10 and 11 are
reserved values.
00
19:18
reserved
-
20
If bits 5:4 are not 10, controls the use of pin P2[29:28]: 0 enables P2[29:28], 1 is
reserved
0
21
If bits 5:4 are not 10, controls the use of pin P2.30: 0 enables P2.30, 1 enables
AIN4.
1
22
If bits 5:4 are not 10, controls the use of pin P2.31: 0 enables P2.31, 1 enables
AIN5.
1
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
21 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 9.
Pin function select register 2 (PINSEL2 - 0xE002 C014) …continued
PINSEL2 bits
Description
Reset value
23
Controls whether P3.0/A0 is a port pin (0) or an address line (1).
1 if BOOT1:0 = 00
at RESET = 0,
0 otherwise
24
Controls whether P3.1/A1 is a port pin (0) or an address line (1).
BOOT1 during
reset
27:25
Controls the number of pins among P3.23/A23/XCLK and P3[22:2]/A2[22:2] that
are address lines:
000 if
BOOT1:0 = 11 at
reset, 111
otherwise
31:28
000 = None
100 = A11 to A2 are address lines.
001 = A3 to A2 are address
lines.
101 = A15 to A2 are address lines.
010 = A5 to A2 are address
lines.
110 = A19 to A2 are address lines.
011 = A7 to A2 are address
lines.
111 = A23 to A2 are address lines.
reserved
6.9 External memory controller
The external Static Memory Controller is a module which provides an interface between
the system bus and external (off-chip) memory devices. It provides support for up to four
independently configurable memory banks (16 MB each with byte lane enable control)
simultaneously. Each memory bank is capable of supporting SRAM, ROM, flash EPROM,
burst ROM memory, or some external I/O devices.
Each memory bank may be 8-bit, 16-bit, or 32-bit wide.
6.10 General purpose parallel I/O
Device pins that are not connected to a specific peripheral function are controlled by the
GPIO registers. Pins may be dynamically configured as inputs or outputs. Separate
registers allow setting or clearing any number of outputs simultaneously. The value of the
output register may be read back, as well as the current state of the port pins.
6.10.1 Features
• Direction control of individual bits.
• Separate control of output set and clear.
• All I/O default to inputs after reset.
6.11 10-bit ADC
The LPC2210/2220 each contain a single 10-bit successive approximation ADC with eight
multiplexed channels.
6.11.1 Features
• Measurement range of 0 V to 3 V.
• Capable of performing more than 400000 10-bit samples per second.
• Burst conversion mode for single or multiple inputs.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
22 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
• Optional conversion on transition on input pin or Timer Match signal.
6.12 UARTs
The LPC2210/2220 each contain two UARTs. One UART provides a full modem control
handshake interface, the other provides only transmit and receive data lines.
6.12.1 Features
•
•
•
•
•
•
16 B Receive and Transmit FIFOs.
Register locations conform to 16C550 industry standard.
Receiver FIFO trigger points at 1 B, 4 B, 8 B, and 14 B.
Built-in baud rate generator.
Standard modem interface signals included on UART1.
LPC2220 provides enhanced UARTs with fractional baud-rate generators,
mechanism for software flow control, and hardware (CTS/RTS) flow control on UART1
only.
6.13 I2C-bus serial I/O controller
The I2C-bus is bidirectional for inter-IC control using only two wires: a serial clock line
(SCL), and a serial data line (SDA). Each device is recognized by a unique address and
can operate as either a receiver-only device (e.g., an LCD driver or a transmitter with the
capability to both receive and send information (such as memory)). Transmitters and/or
receivers can operate in either master or slave mode, depending on whether the chip has
to initiate a data transfer or is only addressed. The I2C-bus is a multi-master bus, it can be
controlled by more than one bus master connected to it.
The I2C-bus implemented in LPC2210/2220 supports a bit rate up to 400 kbit/s (Fast
I2C-bus).
6.13.1 Features
•
•
•
•
•
•
Compliant with standard I2C-bus interface.
Easy to configure as master, slave, or master/slave.
Programmable clocks allow versatile rate control.
Bidirectional data transfer between masters and slaves.
Multi-master bus (no central master).
Arbitration between simultaneously transmitting masters without corruption of serial
data on the bus.
• Serial clock synchronization allows devices with different bit rates to communicate via
one serial bus.
• Serial clock synchronization can be used as a handshake mechanism to suspend and
resume serial transfer.
• The I2C-bus may be used for test and diagnostic purposes.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
23 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.14 SPI serial I/O controller
The LPC2210/2220 each contain two SPIs. The SPI is a full duplex serial interface,
designed to be able to handle multiple masters and slaves connected to a given bus. Only
a single master and a single slave can communicate on the interface during a given data
transfer. During a data transfer the master always sends a byte of data to the slave, and
the slave always sends a byte of data to the master.
6.14.1 Features
•
•
•
•
Compliant with SPI specification.
Synchronous, serial, full duplex, communication.
Combined SPI master and slave.
Maximum data bit rate of one eighth of the input clock rate.
6.15 SSP controller
This peripheral is available in LPC2220 only.
6.15.1 Features
• Compatible with Motorola’s SPI, TI’s 4-wire SSI, and National Semiconductor’s
Microwire buses.
•
•
•
•
Synchronous serial communication.
Master or slave operation.
8-frame FIFOs for both transmit and receive.
Four to 16 bits per frame.
6.15.2 Description
The SSP is a controller capable of operation on a SPI, 4-wire SSI, or Microwire bus. It can
interact with multiple masters and slaves on the bus. Only a single master and a single
slave can communicate on the bus during a given data transfer. Data transfers are in
principle full duplex, with frames of four to 16 bits of data flowing from the master to the
slave and from the slave to the master.
While the SSP and SPI1 peripherals share the same physical pins, it is not possible to
have both of these two peripherals active at the same time. Application can switch on the
fly from SPI1 to SSP and back.
6.16 General purpose timers
The Timer/Counter is designed to count cycles of the peripheral clock (PCLK) or an
externally supplied clock and optionally generate interrupts or perform other actions at
specified timer values, based on four match registers. It also includes four capture inputs
to trap the timer value when an input signal transitions, optionally generating an interrupt.
Multiple pins can be selected to perform a single capture or match function, providing an
application with ‘or’ and ‘and’, as well as ‘broadcast’ functions among them.
The LPC2220 can count external events on one of the capture inputs if the minimum
external pulse is equal or longer than a period of the PCLK. In this configuration, unused
capture lines can be selected as regular timer capture inputs.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
24 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.16.1 Features
• A 32-bit Timer/Counter with a programmable 32-bit prescaler.
• Timer operation (LPC2210/2220) or external Event Counter (LPC2220 only).
• Four 32-bit capture channels per timer/counter that can take a snapshot of the timer
value when an input signal transitions. A capture event may also optionally generate
an interrupt.
• Four 32-bit match registers that allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Four external outputs per timer/counter corresponding to match registers, with the
following capabilities:
– Set LOW on match.
– Set HIGH on match.
– Toggle on match.
– Do nothing on match.
6.17 Watchdog timer
The purpose of the watchdog is to reset the microcontroller within a reasonable amount of
time if it enters an erroneous state. When enabled, the watchdog will generate a system
reset if the user program fails to ‘feed’ (or reload) the watchdog within a predetermined
amount of time.
6.17.1 Features
• Internally resets chip if not periodically reloaded.
• Debug mode.
• Enabled by software but requires a hardware reset or a watchdog reset/interrupt to be
disabled.
•
•
•
•
Incorrect/incomplete feed sequence causes reset/interrupt if enabled.
Flag to indicate watchdog reset.
Programmable 32-bit timer with internal prescaler.
Selectable time period from (Tcy(PCLK) × 256 × 4) to (Tcy(PCLK) × 232 × 4) in multiples of
Tcy(PCLK) × 4.
6.18 Real-time clock
The Real-Time Clock (RTC) is designed to provide a set of counters to measure time
when normal or idle operating mode is selected. The RTC has been designed to use little
power, making it suitable for battery powered systems where the CPU is not running
continuously (Idle mode).
6.18.1 Features
• Measures the passage of time to maintain a calendar and clock.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
25 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
• Ultra-low power design to support battery powered systems.
• Provides Seconds, Minutes, Hours, Day of Month, Month, Year, Day of Week, and Day
of Year.
• Programmable Reference Clock Divider allows adjustment of the RTC to match
various crystal frequencies.
6.19 Pulse width modulator
The PWM is based on the standard Timer block and inherits all of its features, although
only the PWM function is pinned out on the LPC2210/2220. The Timer is designed to
count cycles of the peripheral clock (PCLK) and optionally generate interrupts or perform
other actions when specified timer values occur, based on seven match registers. The
PWM function is also based on match register events.
The ability to separately control rising and falling edge locations allows the PWM to be
used for more applications. For instance, multi-phase motor control typically requires three
non-overlapping PWM outputs with individual control of all three pulse widths and
positions.
Two match registers can be used to provide a single edge controlled PWM output. One
match register (MR0) controls the PWM cycle rate, by resetting the count upon match.
The other match register controls the PWM edge position. Additional single edge
controlled PWM outputs require only one match register each, since the repetition rate is
the same for all PWM outputs. Multiple single edge controlled PWM outputs will all have a
rising edge at the beginning of each PWM cycle, when an MR0 match occurs.
Three match registers can be used to provide a PWM output with both edges controlled.
Again, the MR0 match register controls the PWM cycle rate. The other match registers
control the two PWM edge positions. Additional double edge controlled PWM outputs
require only two match registers each, since the repetition rate is the same for all PWM
outputs.
With double edge controlled PWM outputs, specific match registers control the rising and
falling edge of the output. This allows both positive going PWM pulses (when the rising
edge occurs prior to the falling edge), and negative going PWM pulses (when the falling
edge occurs prior to the rising edge).
6.19.1 Features
• Seven match registers allow up to six single edge controlled or three double edge
controlled PWM outputs, or a mix of both types.
• The match registers also allow:
– Continuous operation with optional interrupt generation on match.
– Stop timer on match with optional interrupt generation.
– Reset timer on match with optional interrupt generation.
• Supports single edge controlled and/or double edge controlled PWM outputs. Single
edge controlled PWM outputs all go HIGH at the beginning of each cycle unless the
output is a constant LOW. Double edge controlled PWM outputs can have either edge
occur at any position within a cycle. This allows for both positive going and negative
going pulses.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
26 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
• Pulse period and width can be any number of timer counts. This allows complete
flexibility in the trade-off between resolution and repetition rate. All PWM outputs will
occur at the same repetition rate.
• Double edge controlled PWM outputs can be programmed to be either positive going
or negative going pulses.
• Match register updates are synchronized with pulse outputs to prevent generation of
erroneous pulses. Software must ‘release’ new match values before they can become
effective.
• May be used as a standard timer if the PWM mode is not enabled.
• A 32-bit Timer/Counter with a programmable 32-bit Prescaler.
6.20 System control
6.20.1 Crystal oscillator
The oscillator supports crystals in the range of 1 MHz to 30 MHz and up to 50 MHz with
the external oscillator. The oscillator output frequency is called fosc and the ARM
processor clock frequency is referred to as CCLK for purposes of rate equations, etc. fosc
and CCLK are the same value unless the PLL is running and connected. Refer to Section
6.20.2 “PLL” for additional information.
6.20.2 PLL
The PLL accepts an input clock frequency in the range of 10 MHz to 25 MHz. The input
frequency is multiplied up into the range of 10 MHz to 60/75 MHz (LPC2210/2220) with a
Current Controlled Oscillator (CCO). The multiplier can be an integer value from 1 to 32
(in practice, the multiplier value cannot be higher than 6 on this family of microcontrollers
due to the upper frequency limit of the CPU). The CCO operates in the range of 156 MHz
to 320 MHz, so there is an additional divider in the loop to keep the CCO within its
frequency range while the PLL is providing the desired output frequency. The output
divider may be set to divide by 2, 4, 8, or 16 to produce the output clock. Since the
minimum output divider value is 2, it is insured that the PLL output has a 50 % duty cycle.
The PLL is turned off and bypassed following a chip reset and may be enabled by
software. The program must configure and activate the PLL, wait for the PLL to Lock, then
connect to the PLL as a clock source. The PLL settling time is 100 µs.
6.20.3 Reset and wake-up timer
Reset has two sources on the LPC2210/2220: the RESET pin and watchdog reset. The
RESET pin is a Schmitt trigger input pin with an additional glitch filter. Assertion of chip
reset by any source starts the Wake-up Timer (see Wake-up Timer description below),
causing the internal chip reset to remain asserted until the external reset is de-asserted,
the oscillator is running, a fixed number of clocks have passed, and the on-chip circuitry
has completed its initialization.
When the internal reset is removed, the processor begins executing at address 0, which is
the reset vector. At that point, all of the processor and peripheral registers have been
initialized to predetermined values.
The Wake-up Timer ensures that the oscillator and other analog functions required for
chip operation are fully functional before the processor is allowed to execute instructions.
This is important at power-on, all types of reset, and whenever any of the aforementioned
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
27 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
functions are turned off for any reason. Since the oscillator and other functions are turned
off during Power-down mode, any wake-up of the processor from Power-down mode
makes use of the Wake-up Timer.
The Wake-up Timer monitors the crystal oscillator as the means of checking whether it is
safe to begin code execution. When power is applied to the chip, or some event caused
the chip to exit Power-down mode, some time is required for the oscillator to produce a
signal of sufficient amplitude to drive the clock logic. The amount of time depends on
many factors, including the rate of VDD ramp (in the case of power on), the type of crystal
and its electrical characteristics (if a quartz crystal is used), as well as any other external
circuitry (e.g. capacitors), and the characteristics of the oscillator itself under the existing
ambient conditions.
6.20.4 External interrupt inputs
The LPC2210/2220 include up to nine edge or level sensitive External Interrupt Inputs as
selectable pin functions. When the pins are combined, external events can be processed
as four independent interrupt signals. The External Interrupt Inputs can optionally be used
to wake up the processor from Power-down mode.
6.20.5 Memory mapping control
The Memory Mapping Control alters the mapping of the interrupt vectors that appear
beginning at address 0x0000 0000. Vectors may be mapped to the bottom of the BANK0
external memory, or to the on-chip static RAM. This allows code running in different
memory spaces to have control of the interrupts.
6.20.6 Power control
The LPC2210/2220 support two reduced power modes: Idle mode and Power-down
mode.
In Idle mode, execution of instructions is suspended until either a reset or interrupt occurs.
Peripheral functions continue operation during Idle mode and may generate interrupts to
cause the processor to resume execution. Idle mode eliminates power used by the
processor itself, memory systems and related controllers, and internal buses.
In Power-down mode, the oscillator is shut down, and the chip receives no internal clocks.
The processor state and registers, peripheral registers, and internal SRAM values are
preserved throughout Power-down mode, and the logic levels of chip output pins remain
static. The Power-down mode can be terminated and normal operation resumed by either
a reset or certain specific interrupts that are able to function without clocks. Since all
dynamic operation of the chip is suspended, Power-down mode reduces chip power
consumption to nearly zero.
A Power Control for Peripherals feature allows individual peripherals to be turned off if
they are not needed in the application, resulting in additional power savings.
6.20.7 APB bus
The APB divider determines the relationship between the processor clock (CCLK) and the
clock used by peripheral devices (PCLK). The APB divider serves two purposes. The first
is to provide peripherals with the desired PCLK via APB bus so that they can operate at
the speed chosen for the ARM processor. In order to achieve this, the APB bus may be
slowed down to 1⁄2 to 1⁄4 of the processor clock rate. Because the APB bus must work
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
28 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
properly at power-up (and its timing cannot be altered if it does not work since the APB
divider control registers reside on the APB bus), the default condition at reset is for the
APB bus to run at 1⁄4 of the processor clock rate. The second purpose of the APB divider
is to allow power savings when an application does not require any peripherals to run at
the full processor rate. Because the APB divider is connected to the PLL output, the PLL
remains active (if it was running) during Idle mode.
6.21 Emulation and debugging
The LPC2210/2220 support emulation and debugging via a JTAG serial port. A trace port
allows tracing program execution. Debugging and trace functions are multiplexed only with
GPIOs on Port 1. This means that all communication, timer and interface peripherals
residing on Port 0 are available during the development and debugging phase as they are
when the application is run in the embedded system itself.
6.21.1 EmbeddedICE
Standard ARM EmbeddedICE logic provides on-chip debug support. The debugging of
the target system requires a host computer running the debugger software and an
EmbeddedICE protocol converter. EmbeddedICE protocol converter converts the Remote
Debug Protocol commands to the JTAG data needed to access the ARM core.
The ARM core has a Debug Communication Channel function built-in. The debug
communication channel allows a program running on the target to communicate with the
host debugger or another separate host without stopping the program flow or even
entering the debug state. The debug communication channel is accessed as a
co-processor 14 by the program running on the ARM7TDMI-S core. The debug
communication channel allows the JTAG port to be used for sending and receiving data
without affecting the normal program flow. The debug communication channel data and
control registers are mapped in to addresses in the EmbeddedICE logic.
6.21.2 Embedded trace
Since the LPC2210/2220 have significant amounts of on-chip memory, it is not possible to
determine how the processor core is operating simply by observing the external pins. The
Embedded Trace Macrocell (ETM) provides real-time trace capability for deeply
embedded processor cores. It outputs information about processor execution to the trace
port.
The ETM is connected directly to the ARM core and not to the main AMBA system bus. It
compresses the trace information and exports it through a narrow trace port. An external
trace port analyzer must capture the trace information under software debugger control.
Instruction trace (or PC trace) shows the flow of execution of the processor and provides a
list of all the instructions that were executed. Instruction trace is significantly compressed
by only broadcasting branch addresses as well as a set of status signals that indicate the
pipeline status on a cycle by cycle basis. Trace information generation can be controlled
by selecting the trigger resource. Trigger resources include address comparators,
counters and sequencers. Since trace information is compressed the software debugger
requires a static image of the code being executed. Self-modifying code cannot be traced
because of this restriction.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
29 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
6.21.3 RealMonitor
RealMonitor is a configurable software module, developed by ARM Inc., which enables
real-time debug. It is a lightweight debug monitor that runs in the background while users
debug their foreground application. It communicates with the host using the Debug
Communications Channel (DCC), which is present in the EmbeddedICE logic. The
LPC2210/2220 contain a specific configuration of RealMonitor software programmed into
the on-chip flash memory.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
30 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
7. Limiting values
Table 10. Limiting values reset
In accordance with the Absolute Maximum Rating System (IEC 60134).[1]
Symbol
Parameter
Conditions
supply voltage (1.8 V)
[2]
VDD(3V3)
supply voltage (3.3 V)
[3]
VDDA(3V3)
analog supply voltage (3.3 V)
VIA
analog input voltage
VDD(1V8)
IDD
ISS
Max
Unit
−0.5
+2.5
V
−0.5
+3.6
V
−0.5
+4.6
V
−0.5
+5.1
V
5 V tolerant I/O pins
[4][5]
−0.5
+6.0
V
other I/O pins
[4][6]
−0.5
VDD(3V3) + 0.5
V
supply current
[7][8]
-
100
mA
ground current
[8][9]
-
100
mA
−65
+150
°C
-
1.5
W
−2000
+2000
V
input voltage
VI
Min
[10]
Tstg
storage temperature
Ptot(pack)
total power dissipation (per
package)
based on package heat
transfer, not device power
consumption
Vesd
electrostatic discharge voltage
human body model
all pins
[11]
[1]
The following applies to Table 10:
a) This product includes circuitry specifically designed for the protection of its internal devices from the damaging effects of excessive
static charge. Nonetheless, it is suggested that conventional precautions be taken to avoid applying greater than the rated maximum.
b) Parameters are valid over operating temperature range unless otherwise specified. All voltages are with respect to VSS unless
otherwise noted.
[2]
Internal rail.
[3]
External rail.
[4]
Including voltage on outputs in 3-state mode.
[5]
Only valid when the VDD(3V3) supply voltage is present.
[6]
Not to exceed 4.6 V.
[7]
Per supply pin.
[8]
The peak current is limited to 25 times the corresponding maximum current.
[9]
Per ground pin.
[10] Dependent on package type.
[11] Human body model: equivalent to discharging a 100 pF capacitor through a 1.5 kΩ series resistor.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
31 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
8. Static characteristics
Table 11. Static characteristics
Tamb = −40 °C to +85 °C for commercial applications, unless otherwise specified.
Symbol
VDD(1V8)
VDD(3V3)
Parameter
Conditions
supply voltage (1.8 V)
[2]
supply voltage (3.3 V)
[3]
VDDA(3V3) analog supply voltage
(3.3 V)
Min
Typ[1]
Max
Unit
1.65
1.8
1.95
V
3.0
3.3
3.6
V
2.5
3.3
3.6
V
Standard port pins, RESET, RTCK
IIL
LOW-level input current
VI = 0 V; no pull-up
-
-
3
µA
IIH
HIGH-level input current
VI = VDD(3V3); no pull-down
-
-
3
µA
IOZ
OFF-state output current
VO = 0 V, VO = VDD(3V3);
no pull-up/down
-
-
3
µA
Ilatch
I/O latch-up current
−(0.5VDD(3V3)) < VI <
(1.5VDD(3V3)); Tj < 125 °C
100
-
-
mA
VI
input voltage
0
-
5.5
V
VO
output voltage
0
-
VDD(3V3)
V
VIH
HIGH-level input voltage
2.0
-
-
V
VIL
LOW-level input voltage
-
-
0.8
V
Vhys
hysteresis voltage
[4][5][6]
output active
-
0.4
-
V
VDD(3V3) −
0.4
-
-
V
VOH
HIGH-level output voltage
IOH = −4 mA
[7]
VOL
LOW-level output voltage
IOL = −4 mA
[7]
-
-
0.4
V
HIGH-level output current
VOH = VDD(3V3) − 0.4 V
[7]
−4
-
-
mA
VOL = 0.4 V
[7]
4
-
-
mA
-
-
−45
mA
-
50
mA
IOH
IOL
LOW-level output current
IOHS
HIGH-level short circuit
current
VOH = 0 V
[8]
IOLS
LOW-level short circuit
current
VOL = VDD(3V3)
[8]
-
Ipd
pull-down current
VI = 5 V
[9]
10
50
150
µA
Ipu
pull-up current
VI = 0 V
[10]
−15
−50
−85
µA
0
0
0
µA
CCLK = 60 MHz
(LPC2210)
-
50
70
mA
CCLK = 75 MHz
(LPC2220)
-
50
70
mA
VDD(3V3) < VI < 5 V
IDD(act)
active mode supply current
[9]
VDD(1V8) = 1.8 V,
Tamb = 25 °C,
code
while(1){}
executed from on-chip
RAM, no active peripherals
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
32 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 11. Static characteristics …continued
Tamb = −40 °C to +85 °C for commercial applications, unless otherwise specified.
Symbol
Parameter
Conditions
Min
Typ[1]
Max
Unit
IDD(pd)
Power-down mode supply
current
VDD(1V8) = 1.8 V,
Tamb = 25 °C,
-
10
-
µA
VDD(1V8) = 1.8 V,
Tamb = 85 °C
-
110
500
µA
V
I2C-bus pins
VIH
HIGH-level input voltage
0.7VDD(3V3)
-
-
VIL
LOW-level input voltage
-
-
0.3VDD(3V3) V
Vhys
hysteresis voltage
-
0.5VDD(3V3) -
V
IOLS = 3 mA
[7]
-
-
0.4
V
VI = VDD(3V3)
[11]
-
2
4
µA
-
10
22
µA
LOW-level output voltage
VOL
input leakage current
ILI
VI = 5 V
Oscillator pins
Vi(XTAL1)
input voltage on pin XTAL1
0
-
1.8
V
Vo(XTAL2)
output voltage on pin XTAL2
0
-
1.8
V
[1]
Typical ratings are not guaranteed. The values listed are at room temperature (+25 °C), nominal supply voltages.
[2]
Internal rail.
[3]
External rail.
[4]
Including voltage on outputs in 3-state mode.
[5]
VDD(3V3) supply voltages must be present.
[6]
3-state outputs go into 3-state mode when VDD(3V3) is grounded.
[7]
Accounts for 100 mV voltage drop in all supply lines.
[8]
Only allowed for a short time period.
[9]
Minimum condition for VI = 4.5 V, maximum condition for VI = 5.5 V.
[10] Applies to P1[25:16].
[11] To VSS.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
33 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 12. ADC static characteristics
VDDA(3V3) = 2.5 V to 3.6 V; Tamb = −40 °C to +85 °C unless otherwise specified. ADC frequency 4.5 MHz.
Symbol
Parameter
VIA
analog input voltage
0
-
VDDA(3V3)
V
Cia
analog input capacitance
-
-
1
pF
ED
differential linearity error
[1][2][3]
-
-
±1
LSB
integral non-linearity
[1][4]
-
-
±2
LSB
EO
offset error
[1][5]
-
-
±3
LSB
EG
gain error
[1][6]
-
-
±0.5
%
absolute error
[1][7]
-
-
±4
LSB
EL(adj)
ET
Conditions
Min
Typ
Max
Unit
[1]
Conditions: VSSA = 0 V, VDDA(3V3) = 3.3 V.
[2]
The ADC is monotonic, there are no missing codes.
[3]
The differential linearity error (ED) is the difference between the actual step width and the ideal step width. See Figure 5.
[4]
The integral non-linearity (EL(adj)) is the peak difference between the center of the steps of the actual and the ideal transfer curve after
appropriate adjustment of gain and offset errors. See Figure 5.
[5]
The offset error (EO) is the absolute difference between the straight line which fits the actual curve and the straight line which fits the
ideal curve. See Figure 5.
[6]
The gain error (EG) is the relative difference in percent between the straight line fitting the actual transfer curve after removing offset
error, and the straight line which fits the ideal transfer curve. See Figure 5.
[7]
The absolute voltage error (ET) is the maximum difference between the center of the steps of the actual transfer curve of the
non-calibrated ADC and the ideal transfer curve. See Figure 5.
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
34 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
gain
error
EG
offset
error
EO
1023
1022
1021
1020
1019
1018
(2)
7
code
out
(1)
6
5
(5)
4
(4)
3
(3)
2
1 LSB
(ideal)
1
0
1
2
3
4
5
6
7
1018
1019
1020
1021
1022
1023
1024
VIA (LSBideal)
1 LSB =
offset
error
EO
VDDA − VSSA
1024
002aaa668
(1) Example of an actual transfer curve.
(2) The ideal transfer curve.
(3) Differential linearity error (ED).
(4) Integral non-linearity (EL(adj)).
(5) Center of a step of the actual transfer curve.
Fig 5. ADC characteristics
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
35 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
9. Dynamic characteristics
Table 13. Dynamic characteristics
Tamb = 0 °C to +70 °C for commercial applications, −40 °C to +85 °C for industrial applications, VDD(1V8), VDD(3V3) over
specified ranges[1]
Symbol
Parameter
Conditions
Min
Typ
Max
Unit
oscillator frequency
supplied by an external
oscillator (signal generator)
1
-
50
MHz
external clock frequency
supplied by an external
crystal oscillator
1
-
30
MHz
external clock frequency if
on-chip PLL is used
10
-
25
MHz
external clock frequency if
on-chip bootloader is used
for initial code download
10
-
25
MHz
20
-
1000
ns
External clock
fosc
Tcy(clk)
clock cycle time
tCHCX
clock HIGH time
Tcy(clk) × 0.4
-
-
ns
tCLCX
clock LOW time
Tcy(clk) × 0.4
-
-
ns
tCLCH
clock rise time
-
-
5
ns
tCHCL
clock fall time
-
-
5
ns
Port pins (except P0.2 and P0.3)
tr
rise time
-
10
-
ns
tf
fall time
-
10
-
ns
-
ns
I2C-bus
pins (P0.2 and P0.3)
fall time
tf
VIH to VIL
[2]
[1]
Parameters are valid over operating temperature range unless otherwise specified.
[2]
Bus capacitance Cb in pF, from 10 pF to 400 pF.
LPC2210_2220_4
Product data sheet
20 + 0.1 × Cb -
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
36 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 14. External memory interface dynamic characteristics
CL = 25 pF, Tamb = 40 °C
Symbol
Parameter
Conditions
Min
Typ Max
Unit
Common to read and write cycles
tCHAV
XCLK HIGH to address valid
time
-
-
10
ns
tCHCSL
XCLK HIGH to CS LOW time
-
-
10
ns
tCHCSH
XCLK HIGH to CS HIGH
time
-
-
10
ns
tCHANV
XCLK HIGH to address
invalid time
-
-
10
ns
Read cycle parameters
tCSLAV
CS LOW to address valid
time
[1]
−5
-
+10
ns
tOELAV
OE LOW to address valid
time
[1]
−5
-
+10
ns
tCSLOEL
CS LOW to OE LOW time
−5
-
+5
ns
(Tcy(CCLK) × (2 + WST1)) +
(−20)
-
-
ns
tam
memory access time
[2][3]
tam(ibr)
memory access time (initial
burst-ROM)
[2][3]
(Tcy(CCLK) × (2 + WST1)) +
(−20)
-
-
ns
tam(sbr)
memory access time
(subsequent burst-ROM)
[2][4]
Tcy(CCLK) + (−20)
-
-
ns
th(D)
data hold time
0
-
-
ns
tCSHOEH
CS HIGH to OE HIGH time
−5
-
+5
ns
tOEHANV
OE HIGH to address invalid
time
−5
-
+5
ns
tCHOEL
XCLK HIGH to OE LOW time
−5
-
+5
ns
tCHOEH
XCLK HIGH to OE HIGH
time
−5
-
+5
ns
Tcy(CCLK) − 10
-
-
ns
[5]
Write cycle parameters
[1]
tAVCSL
address valid to CS LOW
time
tCSLDV
CS LOW to data valid time
−5
-
+5
ns
tCSLWEL
CS LOW to WE LOW time
−5
-
+5
ns
tCSLBLSL
CS LOW to BLS LOW time
−5
-
+5
ns
tWELDV
WE LOW to data valid time
−5
-
+5
ns
tCSLDV
CS LOW to data valid time
−5
-
+5
ns
Tcy(CCLK) × (1 + WST2) − 5
-
Tcy(CCLK) × (1 +
WST2) + 5
ns
tWELWEH
WE LOW to WE HIGH time
[2]
tBLSLBLSH
BLS LOW to BLS HIGH time
[2]
Tcy(CCLK) × (1 + WST2) − 5
-
Tcy(CCLK) ×
(1 + WST2) + 5
ns
tWEHANV
WE HIGH to address invalid
time
[2]
Tcy(CCLK) − 5
-
Tcy(CCLK) + 5
ns
tWEHDNV
WE HIGH to data invalid time
[2]
(2 × Tcy(CCLK)) − 5
-
(2 × Tcy(CCLK)) + 5 ns
BLS HIGH to address invalid
time
[2]
Tcy(CCLK) − 5
-
Tcy(CCLK) + 5
tBLSHANV
LPC2210_2220_4
Product data sheet
ns
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
37 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
Table 14. External memory interface dynamic characteristics …continued
CL = 25 pF, Tamb = 40 °C
Symbol
Parameter
Conditions
[2]
Min
Typ Max
Unit
(2 × Tcy(CCLK)) − 5
-
(2 × Tcy(CCLK)) + 5 ns
tBLSHDNV
BLS HIGH to data invalid
time
tCHDV
XCLK HIGH to data valid
time
-
-
10
ns
tCHWEL
XCLK HIGH to WE LOW
time
-
-
10
ns
tCHBLSL
XCLK HIGH to BLS LOW
time
-
-
10
ns
tCHWEH
XCLK HIGH to WE HIGH
time
-
-
10
ns
tCHBLSH
XCLK HIGH to BLS HIGH
time
-
-
10
ns
tCHDNV
XCLK HIGH to data invalid
time
-
-
10
ns
[1]
Except on initial access, in which case the address is set up Tcy(CCLK) earlier.
[2]
Tcy(CCLK) = 1⁄CCLK.
[3]
Latest of address valid, CS LOW, OE LOW to data valid.
[4]
Address valid to data valid.
[5]
Earliest of CS HIGH, OE HIGH, address change to data invalid.
Table 15.
Standard read access specifications
Access cycle
Max frequency
WST setting
Memory access time requirement
WST ≥ 0; round up to
integer
standard read
2 + WST 1
f MAX ≤ -------------------------------t RAM + 20 ns
t RAM + 20 ns
WST 1 ≥ -------------------------------- – 2
t cy ( CCLK )
t RAM ≤ t cy ( CCLK ) × ( 2 + WST 1 ) – 20 ns
standard write
1 + WST 2
f MAX ≤ ---------------------------------t WRITE + 5 ns
t WRITE – t CYC + 5
WST 2 ≥ -------------------------------------------t cy ( CCLK )
t WRITE ≤ t cy ( CCLK ) × ( 1 + WST 2 ) – 5 ns
burst read - initial
2 + WST 1
f MAX ≤ -------------------------------t INIT + 20 ns
t INIT + 20 ns
WST 1 ≥ -------------------------------- – 2
t cy ( CCLK )
t INIT ≤ t cy ( CCLK ) × ( 2 + WST 1 ) – 20 ns
burst read - subsequent 3×
1
f MAX ≤ --------------------------------t ROM + 20 ns
N/A
t ROM ≤ t cy ( CCLK ) – 20 ns
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
38 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
9.1 Timing
XCLK
tCSLAV
tCSHOEH
CS
addr
tam
th(D)
data
tCSLOEL
tOELAV
tOEHANV
OE
tCHOEL
tCHOEH
002aaa749
Fig 6. External memory read access
XCLK
tCSLDV
CS
tAVCSL
tCSLWEL
tWELWEH
tBLSLBLSH
BLS/WE
tWEHANV
tCSLBLSL
tWELDV
tBLSHANV
addr
tCSLDV
tWEHDNV
tBLSHDNV
data
OE
002aaa750
Fig 7. External memory write access
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
39 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
VDD − 0.5 V
0.2VDD + 0.9 V
0.2VDD − 0.1 V
0.45 V
tCHCX
tCHCL
tCLCX
tCLCH
Tclk
002aaa416
Fig 8. External clock timing
9.2 LPC2210 power consumption measurements
002aab452
60
IDD current
(mA)
(1)
(2)
40
20
0
0
10
20
30
40
50
60
frequency (MHz)
Test conditions: code executed from on-chip RAM; all peripherals are enabled in PCONP register; PCLK = CCLK/4.
(1) 1.8 V core at 25 °C (typical)
(2) 1.65 V core at 25 °C (typical)
Fig 9. LPC2210 IDD(1V8) active measured at different frequencies (CCLK) and temperatures
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
40 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aab453
15
IDD current
(mA)
10
(1)
(2)
5
0
0
10
20
30
40
50
60
frequency (MHz)
Test conditions: Idle mode entered executing code from on-chip RAM; all peripherals are enabled in PCONP register;
PCLK = CCLK/4.
(1) 1.8 V core at 25 °C (typical)
(2) 1.65 V core at 25 °C (typical)
Fig 10. LPC2210 IDD(1V8) idle measured at different frequencies (CCLK) and temperatures
002aab454
500
IDD current
(µA)
(1)
(2)
400
(3)
300
200
100
0
−100
−50
0
50
100
150
temp (°C)
Test conditions: Power-down mode entered executing code from on-chip RAM; all peripherals are enabled in PCONP
register.
(1) 1.95 V core
(2) 1.8 V core
(3) 1.65 V core
Fig 11. LPC2210 IDD(1V8) power-down measured at different temperatures
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
41 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
9.3 LPC2220 power consumption measurements
002aab455
40
(1)
IDD current
(mA)
(2)
(3)
30
20
10
0
0
10
20
30
40
50
60
frequency (MHz)
Test conditions: code executed from on-chip RAM; all peripherals are enabled in PCONP register; PCLK = CCLK/4.
(1) 1.8 V core at 85 °C (typical)
(2) 1.8 V core at 25 °C (typical)
(3) 1.65 V core at 25 °C (typical)
Fig 12. LPC2220 IDD(1V8) active measured at different frequencies (CCLK) and temperatures
002aab456
10
(1)
IDD current
(mA)
(2)
8
(3)
6
4
2
0
0
10
20
30
40
50
60
frequency (MHz)
Test conditions: Idle mode entered executing code from on-chip RAM; all peripherals are enabled in PCONP register;
PCLK = CCLK/4.
(1) 1.8 V core at 85 °C (typical)
(2) 1.8 V core at 25 °C (typical)
(3) 1.65 V core at 25 °C (typical)
Fig 13. LPC2220 IDD(1V8) idle measured at different frequencies (CCLK) and temperatures
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
42 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
002aab457
800
(1)
IDD current
(mA)
(2)
600
400
200
0
0
−20
20
60
100
140
temp (°C)
Test conditions: Power-down mode entered executing code from on-chip RAM; all peripherals are enabled in PCONP
register.
(1) 1.8 V core (typical)
(2) 1.65 V core (typical)
Fig 14. LPC2220 IDD(1V8) power-down measured at different temperatures
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
43 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
10. Package outline
LQFP144: plastic low profile quad flat package; 144 leads; body 20 x 20 x 1.4 mm
SOT486-1
c
y
X
A
73
72
108
109
ZE
e
E HE
A A2
(A 3)
A1
θ
wM
Lp
bp
L
pin 1 index
detail X
37
144
1
36
v M A
ZD
wM
bp
e
D
B
HD
v M B
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
A3
bp
c
D (1)
E (1)
e
mm
1.6
0.15
0.05
1.45
1.35
0.25
0.27
0.17
0.20
0.09
20.1
19.9
20.1
19.9
0.5
HD
HE
22.15 22.15
21.85 21.85
L
Lp
v
w
y
1
0.75
0.45
0.2
0.08
0.08
Z D(1) Z E(1)
1.4
1.1
1.4
1.1
θ
o
7
o
0
Note
1. Plastic or metal protrusions of 0.25 mm maximum per side are not included.
REFERENCES
OUTLINE
VERSION
IEC
JEDEC
SOT486-1
136E23
MS-026
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
00-03-14
03-02-20
Fig 15. Package outline SOT486-1 (LQFP144)
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
44 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
TFBGA144: plastic thin fine-pitch ball grid array package; 144 balls; body 12 x 12 x 0.8 mm
SOT569-1
B
D
A
D1
ball A1
index area
A2
A
E1 E
A1
detail X
C
e1
ball A1
index area
∅v M C A B
b
e
N
M
L
K
J
H
G
F
E
D
C
B
A
shape
optional (4×)
y1 C
y
∅w M C
e
e2
1 2 3 4 5 6 7 8 9 10 11 12 13
X
0
5
10 mm
scale
DIMENSIONS (mm are the original dimensions)
UNIT
A
max.
A1
A2
b
D
D1
E
E1
e
e1
e2
v
w
y
y1
mm
1.2
0.36
0.24
0.84
0.74
0.53
0.43
12.2
11.8
11.9
11.7
12.2
11.8
11.9
11.7
0.8
9.6
9.6
0.15
0.08
0.1
0.1
OUTLINE
VERSION
SOT569-1
REFERENCES
IEC
JEDEC
JEITA
EUROPEAN
PROJECTION
ISSUE DATE
03-07-09
05-09-14
MO-216
Fig 16. Package outline SOT569-1 (TFBGA144)
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
45 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
11. Abbreviations
Table 16.
Acronym list
Acronym
Description
ADC
Analog-to-Digital Converter
AMBA
Advanced Microcontroller Bus Architecture
APB
Advanced Peripheral Bus
CISC
Complex Instruction Set Computer
FIFO
First In, First Out
GPIO
General Purpose Input/Output
PWM
Pulse Width Modulator
RISC
Reduced Instruction Set Computer
SPI
Serial Peripheral Interface
SSI
Serial Synchronous Interface
SRAM
Static Random Access Memory
TTL
Transistor-Transistor Logic
UART
Universal Asynchronous Receiver/Transmitter
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
46 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
12. Revision history
Table 17.
Revision history
Document ID
Release date
Data sheet status
Change notice
Supersedes
LPC2210_2220_4
20071002
Product data sheet
-
LPC2210_2220_3
-
LPC2210_2220_2
Modifications:
LPC2210_2220_3
Modifications:
•
Figure 1: changed incorrect character font
20070213
Product data sheet
•
The format of this data sheet has been redesigned to comply with the new identity
guidelines of NXP Semiconductors.
•
•
Legal texts have been adapted to the new company name where appropriate.
Added new device LPC2220FET144/G.
LPC2210_2220_2
20050530
Product data sheet
-
LPC2210-01
20040209
Preliminary data
-
LPC2210_2220_4
Product data sheet
LPC2210-01
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
47 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
13. Legal information
13.1 Data sheet status
Document status[1][2]
Product status[3]
Definition
Objective [short] data sheet
Development
This document contains data from the objective specification for product development.
Preliminary [short] data sheet
Qualification
This document contains data from the preliminary specification.
Product [short] data sheet
Production
This document contains the product specification.
[1]
Please consult the most recently issued document before initiating or completing a design.
[2]
The term ‘short data sheet’ is explained in section “Definitions”.
[3]
The product status of device(s) described in this document may have changed since this document was published and may differ in case of multiple devices. The latest product status
information is available on the Internet at URL http://www.nxp.com.
13.2 Definitions
Draft — The document is a draft version only. The content is still under
internal review and subject to formal approval, which may result in
modifications or additions. NXP Semiconductors does not give any
representations or warranties as to the accuracy or completeness of
information included herein and shall have no liability for the consequences of
use of such information.
Short data sheet — A short data sheet is an extract from a full data sheet
with the same product type number(s) and title. A short data sheet is intended
for quick reference only and should not be relied upon to contain detailed and
full information. For detailed and full information see the relevant full data
sheet, which is available on request via the local NXP Semiconductors sales
office. In case of any inconsistency or conflict with the short data sheet, the
full data sheet shall prevail.
13.3 Disclaimers
General — Information in this document is believed to be accurate and
reliable. However, NXP Semiconductors does not give any representations or
warranties, expressed or implied, as to the accuracy or completeness of such
information and shall have no liability for the consequences of use of such
information.
Right to make changes — NXP Semiconductors reserves the right to make
changes to information published in this document, including without
limitation specifications and product descriptions, at any time and without
notice. This document supersedes and replaces all information supplied prior
to the publication hereof.
Suitability for use — NXP Semiconductors products are not designed,
authorized or warranted to be suitable for use in medical, military, aircraft,
space or life support equipment, nor in applications where failure or
malfunction of a NXP Semiconductors product can reasonably be expected to
result in personal injury, death or severe property or environmental damage.
NXP Semiconductors accepts no liability for inclusion and/or use of NXP
Semiconductors products in such equipment or applications and therefore
such inclusion and/or use is at the customer’s own risk.
Applications — Applications that are described herein for any of these
products are for illustrative purposes only. NXP Semiconductors makes no
representation or warranty that such applications will be suitable for the
specified use without further testing or modification.
Limiting values — Stress above one or more limiting values (as defined in
the Absolute Maximum Ratings System of IEC 60134) may cause permanent
damage to the device. Limiting values are stress ratings only and operation of
the device at these or any other conditions above those given in the
Characteristics sections of this document is not implied. Exposure to limiting
values for extended periods may affect device reliability.
Terms and conditions of sale — NXP Semiconductors products are sold
subject to the general terms and conditions of commercial sale, as published
at http://www.nxp.com/profile/terms, including those pertaining to warranty,
intellectual property rights infringement and limitation of liability, unless
explicitly otherwise agreed to in writing by NXP Semiconductors. In case of
any inconsistency or conflict between information in this document and such
terms and conditions, the latter will prevail.
No offer to sell or license — Nothing in this document may be interpreted
or construed as an offer to sell products that is open for acceptance or the
grant, conveyance or implication of any license under any copyrights, patents
or other industrial or intellectual property rights.
13.4 Trademarks
Notice: All referenced brands, product names, service names and trademarks
are the property of their respective owners.
I2C-bus — logo is a trademark of NXP B.V.
14. Contact information
For additional information, please visit: http://www.nxp.com
For sales office addresses, send an email to: [email protected]
LPC2210_2220_4
Product data sheet
© NXP B.V. 2007. All rights reserved.
Rev. 04 — 2 October 2007
48 of 49
LPC2210/2220
NXP Semiconductors
16/32-bit ARM microcontrollers with external memory interface
15. Contents
1
2
2.1
3
3.1
4
5
5.1
5.2
6
6.1
6.2
6.3
6.4
6.4.1
6.5
6.6
6.7
6.8
6.9
6.10
6.10.1
6.11
6.11.1
6.12
6.12.1
6.13
6.13.1
6.14
6.14.1
6.15
6.15.1
6.15.2
6.16
6.16.1
6.17
6.17.1
6.18
6.18.1
6.19
6.19.1
6.20
6.20.1
6.20.2
General description . . . . . . . . . . . . . . . . . . . . . . 1
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Key features . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Ordering information . . . . . . . . . . . . . . . . . . . . . 2
Ordering options . . . . . . . . . . . . . . . . . . . . . . . . 2
Block diagram . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Pinning information . . . . . . . . . . . . . . . . . . . . . . 4
Pinning . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4
Pin description . . . . . . . . . . . . . . . . . . . . . . . . . 7
Functional description . . . . . . . . . . . . . . . . . . 14
Architectural overview. . . . . . . . . . . . . . . . . . . 14
On-chip SRAM . . . . . . . . . . . . . . . . . . . . . . . . 14
Memory map. . . . . . . . . . . . . . . . . . . . . . . . . . 14
Interrupt controller . . . . . . . . . . . . . . . . . . . . . 15
Interrupt sources. . . . . . . . . . . . . . . . . . . . . . . 16
Pin connect block . . . . . . . . . . . . . . . . . . . . . . 17
Pin function select register 0
(PINSEL0 - 0xE002 C000) . . . . . . . . . . . . . . . 17
Pin function select register 1
(PINSEL1 - 0xE002 C004) . . . . . . . . . . . . . . . 19
Pin function select register 2
(PINSEL2 - 0xE002 C014) . . . . . . . . . . . . . . . 21
External memory controller. . . . . . . . . . . . . . . 22
General purpose parallel I/O. . . . . . . . . . . . . . 22
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
10-bit ADC . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
UARTs . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
I2C-bus serial I/O controller . . . . . . . . . . . . . . 23
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 23
SPI serial I/O controller. . . . . . . . . . . . . . . . . . 24
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
SSP controller. . . . . . . . . . . . . . . . . . . . . . . . . 24
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
Description . . . . . . . . . . . . . . . . . . . . . . . . . . . 24
General purpose timers . . . . . . . . . . . . . . . . . 24
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Watchdog timer. . . . . . . . . . . . . . . . . . . . . . . . 25
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Real-time clock . . . . . . . . . . . . . . . . . . . . . . . . 25
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25
Pulse width modulator . . . . . . . . . . . . . . . . . . 26
Features . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26
System control . . . . . . . . . . . . . . . . . . . . . . . . 27
Crystal oscillator . . . . . . . . . . . . . . . . . . . . . . . 27
PLL . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27
6.20.3
6.20.4
6.20.5
6.20.6
6.20.7
6.21
6.21.1
6.21.2
6.21.3
7
8
9
9.1
9.2
9.3
10
11
12
13
13.1
13.2
13.3
13.4
14
15
Reset and wake-up timer . . . . . . . . . . . . . . . .
External interrupt inputs . . . . . . . . . . . . . . . . .
Memory mapping control . . . . . . . . . . . . . . . .
Power control . . . . . . . . . . . . . . . . . . . . . . . . .
APB bus . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Emulation and debugging. . . . . . . . . . . . . . . .
EmbeddedICE . . . . . . . . . . . . . . . . . . . . . . . .
Embedded trace. . . . . . . . . . . . . . . . . . . . . . .
RealMonitor . . . . . . . . . . . . . . . . . . . . . . . . . .
Limiting values . . . . . . . . . . . . . . . . . . . . . . . .
Static characteristics . . . . . . . . . . . . . . . . . . .
Dynamic characteristics . . . . . . . . . . . . . . . . .
Timing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
LPC2210 power consumption measurements
LPC2220 power consumption measurements
Package outline . . . . . . . . . . . . . . . . . . . . . . . .
Abbreviations . . . . . . . . . . . . . . . . . . . . . . . . .
Revision history . . . . . . . . . . . . . . . . . . . . . . .
Legal information . . . . . . . . . . . . . . . . . . . . . .
Data sheet status . . . . . . . . . . . . . . . . . . . . . .
Definitions . . . . . . . . . . . . . . . . . . . . . . . . . . .
Disclaimers. . . . . . . . . . . . . . . . . . . . . . . . . . .
Trademarks . . . . . . . . . . . . . . . . . . . . . . . . . .
Contact information . . . . . . . . . . . . . . . . . . . .
Contents. . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
27
28
28
28
28
29
29
29
30
31
32
36
39
40
42
44
46
47
48
48
48
48
48
48
49
Please be aware that important notices concerning this document and the product(s)
described herein, have been included in section ‘Legal information’.
© NXP B.V. 2007.
All rights reserved.
For more information, please visit: http://www.nxp.com
For sales office addresses, please send an email to: [email protected]
Date of release: 2 October 2007
Document identifier: LPC2210_2220_4