LINER LT1496

LT6016/LT6017
Dual/Quad 3.2MHz, 0.8V/µs
Low Power, Over-The-Top
Precision Op Amp
DESCRIPTION
FEATURES
n
n
n
n
n
n
n
n
n
n
n
n
n
n
Input Common Mode Range: V– to V– + 76V
Rail-to-Rail Input and Output
Low Power: 315μA/Amplifier
Operating Temperature Range: –55°C to 150°C
VOS: ±50μV (Maximum)
CMRR, PSRR: 126dB
Reverse Battery Protection to 50V
Gain Bandwidth Product: 3.2MHz
Specified on 5V and ±15V Supplies
High Voltage Gain: 1000V/mV
No Phase Reversal
No Supply Sequencing Problems
Dual 8-Lead MSOP
Quad 22-Lead DFN (6mm × 3mm)
APPLICATIONS
n
n
n
n
n
The LT®6016/LT6017 are dual and quad rail-to-rail input
operational amplifiers with input offset voltage trimmed to
less than 50μV. These amplifiers operate on single and split
supplies with a total voltage of 3V to 50V and draw only
315μA per amplifier. They are reverse battery protected,
drawing very little current for reverse supplies up to 50V.
The Over-The-Top® input stage of the LT6016/LT6017 is designed to provide added protection in tough environments.
The input common mode range extends from V– to V+ and
beyond: these amplifiers operate with inputs up to 76V
above V– independent of V+. Internal resistors protect the
inputs against transient faults up to 25V below the negative
supply. The LT6016/LT6017 can drive loads up to 25mA
and are unity-gain stable with capacitive loads as large
as 200pF. Optional external compensation can be added
to extend the capacitive drive capability beyond 200pF.
The LT6016 dual op amp is available in an 8-lead MSOP
package. The LT6017 is offered in a 22-pin leadless DFN
package.
High Side or Low Side Current Sensing
Battery/Power Supply Monitoring
4mA to 20mA Transmitters
High Voltage Data Acquisition
Battery/Portable Instrumentation
L, LT, LTC, LTM, Linear Technology, Over-The-Top and the Linear logo are registered
trademarks of Linear Technology Corporation. All other trademarks are the property of their
respective owners.
TYPICAL APPLICATION
Output Error vs Load Current
Precision High Voltage High Side Load Current Monitor
0.2
0.1Ω
10W
LOAD
200Ω
0.1μF
+
100Ω
1%
LT6016
BSP89
–
1V/A
0V TO 1V OUT
2k
60167 TA01a
OUTPUT ERROR (%)
200Ω
0
5V
VBAT = 1.5V TO 76V
–0.2
–0.4
–0.6
VBAT = 1.5V
VBAT = 5V
VBAT = 20V
VBAT = 75V
–0.8
–1.0
0.01
0.1
LOAD CURRENT (A)
1
60167 TA01b
60167fa
1
LT6016/LT6017
ABSOLUTE MAXIMUM RATINGS
(Note 1)
Supply Voltage (V+ to V–)................................60V, –50V
Input Differential Voltage ........................................±80V
Input Voltage (Note 2) .....................................80V, –25V
Input Current (Note 2) .......................................... ±10mA
Output Short Circuit Duration
(Note 3) ......................................................... Continuous
Temperature Range (Notes 4, 5)
LT6016I/LT6017I ..................................–40°C to 85°C
LT6016H/LT6017H ............................. –40°C to 125°C
LT6016MP/LT6017MP(TJUNCTION) ..... –55°C to 150°C
Storage Temperature Range .................. –65°C to 150°C
Maximum Junction Temperature .......................... 150°C
Lead Temperature (Soldering, 10sec).................... 300°C
PIN CONFIGURATION
TOP VIEW
OUTA
1
–INA
2
22 OUTD
21 –IND
A
D
+INA
3
N/C
4
19 N/C
V–
5
18 V +
N/C
6
V–
7
16 V +
N/C
8
15 N/C
+INB
9
14 +INC
–INB 10
23
B
20 +IND
TOP VIEW
OUTA
–INA
+INA
V–
17 N/C
C
OUTB 11
1
2
3
4
A
B
8
7
6
5
V+
OUTB
–INB
+INB
MS8 PACKAGE
8-LEAD PLASTIC MSOP
TJMAX = 150°C, θJA = 273°C/W, θJC = 45°C/W
13 –INC
12 OUTC
DJC PACKAGE
22-LEAD (6mm × 3mm) PLASTIC DFN
TJMAX = 150°C, θJA = 31.8°C/W, θJC = 4.3°C/W
UNDERSIDE METAL INTERNALLY CONNECTED TO V–
ORDER INFORMATION
LEAD FREE FINISH
TAPE AND REEL
PART MARKING*
PACKAGE DESCRIPTION
TEMPERATURE RANGE
LT6016IMS8#PBF
LT6016IMS8#TRPBF
LTGFK
8-Lead Plastic MSOP
–40°C to 85°C
LT6016HMS8#PBF
LT6016HMS8#TRPBF
LTGFK
8-Lead Plastic MSOP
–40°C to 125°C
LT6016MPMS8#PBF
LT6016MPMS8#TRPBF
LTGFK
8-Lead Plastic MSOP
–55°C to 150°C
LT6017IDJC#PBF
LT6017IDJC#TRPBF
6017
22-Lead Plastic DFN
–40°C to 85°C
LT6017HDJC#PBF
LT6017HDJC#TRPBF
6017
22-Lead Plastic DFN
–40°C to 125°C
LT6017MPDJC#PBF
LT6017MPDJC#TRPBF
6017
22-Lead Plastic DFN
–55°C to 150°C
Consult LTC Marketing for parts specified with wider operating temperature ranges. *The temperature grade is identified by a label on the shipping container.
For more information on lead free part marking, go to: http://www.linear.com/leadfree/
For more information on tape and reel specifications, go to: http://www.linear.com/tapeandreel/
60167fa
2
LT6016/LT6017
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified
temperature range, –40°C < TA < 85°C for I-grade parts, –40°C < TA < 125°C for H–grade parts, otherwise specifications are at
TA = 25°C, VS = 5V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
VOS
ΔVOS
ΔTEMP
ΔVOS
ΔTIME
IB
IOS
Input Offset Voltage
CONDITIONS
MIN
I-, H-GRADE
TYP
MAX
–50
±25
50
μV
μV
–80
–125
–135
–250
–350
±45
±50
±50
±45
±50
80
125
135
250
350
μV
μV
μV
μV
μV
< V+ – 1.75V
0 < VCM
MS8 Package
0 < VCM < V+ – 1.75V
DJC22 Package
VCM = 5V
VCM =76V
0 < VCM < V+ – 1.75V
VCM = 5V to VCM = 76V
l
l
UNITS
Input Offset Voltage Drift
0.75
μV/°C
Long Term Voltage Offset Stability
0.75
μV/Mo
Input Bias Current
Input Offset Current
VCMR
Common Mode Input Range
CIN
Differential Input Capacitance
RIN
Differential Input Resistance
RINCM
en
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V
VS = 0V, VCM = 0V to 76V
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V (Note 6)
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V (Note 6)
–5
–30
11
–15
–150
7
±2
–16.5
14
±2
–16.5
14
0.001
5
0
17.5
15
0
23
1
nA
nA
μA
nA
nA
μA
μA
l
l
l
–5
–5
–500
–15
–15
–500
±2
±2
±50
±2
±2
±50
5
5
500
15
15
500
nA
nA
nA
nA
nA
nA
l
0
l
l
l
l
76
V
5
pF
0 < VCM < V+ – 1.75V
VCM > V+
1
3.7
MΩ
kΩ
Common Mode Input Resistance
0 < VCM < V+ – 1.75V
VCM > V+
>1
>100
GΩ
MΩ
Input Referred Noise Voltage Density
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
18
25
nV/√Hz
nV/√Hz
0.5
μVP-P
0.1
11.5
pA/√Hz
pA/√Hz
Input Referred Noise Voltage
f = 0.1Hz to 10Hz
VCM < V+ – 1.75V
in
Input Referred Noise Current Density
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
AVOL
Open Loop Gain
RL = 10kΩ
ΔVOUT = 3V
l
300
3000
V/mV
PSRR
Supply Rejection Ratio
VS = ±1.65V to ±15V
VCM = VOUT = Mid-Supply
l
110
126
dB
CMRR
Input Common Mode Rejection Ratio
VCM = 0V to 3.25V
VCM = 5V to 76V
l
l
100
126
126
140
dB
dB
VOL
Output Voltage Swing Low
VS = 5V, No Load
VS = 5V, 5mA
l
l
3
280
55
500
mV
mV
VOH
Output Voltage Swing High
VS = 5V, No Load
VS = 5V, 5mA
l
l
450
1000
700
1250
mV
mV
ISC
Short-Circuit Current
VS = 5V, 50Ω to V+
VS = 5V, 50Ω to V–
l
l
10
10
25
25
mA
mA
60167fa
3
LT6016/LT6017
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified
temperature range, –40°C < TA < 85°C for I-grade parts, –40°C < TA < 125°C for H–grade parts, otherwise specifications are at
TA = 25°C, VS = 5V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
CONDITIONS
GBW
Gain Bandwidth Products
fTEST = 10kHz
SR
Slew Rate
ΔVOUT = 3V
tS
Settling Time Due to Input Step
ΔVOUT = ±2V
0.1% Settling
VS
Supply Voltage
Reverse Supply (Note 7)
IS < –25μA/Amplifier
IS
Supply Current Per Amplifier
VS = 5V
RO
Output Impedance
ΔIO = ±5mA
MIN
I-, H-GRADE
TYP
l
2.85
2.5
3.2
3.2
MHz
MHz
l
0.55
0.45
0.75
0.75
V/μs
V/μs
3.5
μs
l
l
3
3.3
l
MAX
UNITS
–65
50
50
–50
V
V
V
315
315
335
500
μA
μA
0.15
Ω
The l denotes the specifications which apply over the specified temperature range, –40°C < TA < 85°C for I-grade parts, –40°C < TA <
125°C for H–grade parts, otherwise specifications are at TA = 25°C, VS = ±15V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
VOSI
CONDITIONS
Input Offset Voltage
l
VS = ±25V
VS = ±25V
ΔVOSI
ΔTEMP
Input Offset Voltage Drift
IB
Input Bias Current
IOS
Input Offset Current
VCMR
Common Mode Input Range
CIN
Differential Input Capacitance
RIN
Differential Input Resistance
RINCM
Common Mode Input Resistance
en
Input Referred Noise Voltage Density
l
MIN
I-, H-GRADE
TYP
MAX
UNITS
–80
–250
–110
–250
±55
±55
±75
±75
80
250
110
250
μV
μV
μV
μV
0.75
μV/°C
l
–5
–15
±2
±2
5
15
nA
nA
l
–5
–15
±2
±2
5
15
nA
nA
l
–15
61
V
0 < VCM < V+ – 1.75V
VCM > V+
0 < VCM < V+ – 1.75V
VCM > V+
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
5
pF
1
3.7
MΩ
kΩ
>1
>100
GΩ
MΩ
18
25
nV/√Hz
nV/√Hz
0.5
μVP-P
0.1
11.5
pA/√Hz
pA/√Hz
Input Referred Noise Voltage
f = 0.1Hz to 10Hz
VCM < V+ – 1.25V
in
Input Referred Noise Current Density
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
AVOL
Open Loop Gain
RL = 10kΩ
ΔVOUT = 27V
l
200
1000
V/mV
PSRR
Supply Rejection Ratio
VS = ±2.5V to ±25V
VCM = VOUT = 0V
l
114
126
dB
CMRR
Input Common Mode Rejection Ratio
VCM = –15V to 13.25V
l
110
126
dB
VOL
Output Voltage Swing Low
VS = ±15V, No Load
VS = ±15V, 5mA
l
l
3
280
55
500
mV
mV
VOH
Output Voltage Swing High
VS = ±15V, No Load
VS = ±15V, 5mA
l
l
450
1000
700
1250
mV
mV
60167fa
4
LT6016/LT6017
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified
temperature range, –40°C < TA < 85°C for I-grade parts, –40°C < TA < 125°C for H–grade parts, otherwise specifications are at
TA = 25°C, VS = ±15V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
ISC
Short-Circuit Current
VS = ±15V, 50Ω to GND
VS = ±15V, 50Ω to GND
GBW
Gain Bandwidth Product
fTEST = 10kHz
SR
Slew Rate
ΔVOUT = 3V
tS
Settling Time Due to Input Step
0.1% Settling
ΔVOUT = ±2V
VS
Supply Voltage
Reverse Supply
IS
IS = –25μA/Amplifier
Supply Current Per Amplifier
Output Impedance
I-, H-GRADE
TYP
l
l
10
10
30
32
mA
mA
l
2.9
2.55
3.3
3.3
MHz
MHz
l
0.6
0.5
0.8
0.8
V/μs
V/μs
3.5
μs
l
l
3
3.3
l
VS = ±25V
VS = ±25V
RO
MIN
CONDITIONS
l
ΔIO = ±5mA
MAX
UNITS
–65
50
50
–30
V
V
V
325
325
340
340
350
525
360
550
μA
μA
μA
μA
0.15
Ω
The l denotes the specifications which apply over the specified temperature range, –55°C < TJUNCTION < 150°C for MP-grade parts,
otherwise specifications are at TA = 25°C, VS = 5V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
VOS
ΔVOS
ΔTEMP
ΔVOS
ΔTIME
IB
IOS
Input Offset Voltage
CONDITIONS
0 < VCM < V+ – 1.75V
MS8 Package
0 < VCM < V+ – 1.75V
DJC22 Package
VCM = 5V
VCM = 76V
0 < VCM < V+ –1.75V
VCM = 5V to VCM = 76V
l
l
MIN
MP-GRADE
TYP
MAX
–50
±25
50
μV
μV
–80
–125
–135
–500
–600
±45
±50
±50
±45
±50
80
125
135
500
600
μV
μV
μV
μV
μV
UNITS
Input Offset Voltage Drift
0.75
μV/°C
Long Term Voltage Offset Stability
0.75
μV/Mo
Input Bias Current
Input Offset Current
VCMR
Common Mode Input Range
CIN
Differential Input Capacitance
RIN
Differential Input Resistance
RINCM
Common Mode Input Resistance
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V
VS = 0V, VCM = 0V to 76V
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V (Note 6)
0.25V < VCM < V+ – 1.75V
VCM = 0V
VCM = 5V to 76V (Note 6)
0 < VCM < V+ – 1.75V
VCM > V+
0 < VCM < V+ – 1.75V
VCM > V+
–5
–30
11
–100
–500
6.5
±2
–16.5
14
±2
–16.5
14
0.001
5
0
17.5
100
0
24
4
nA
nA
μA
nA
nA
μA
μA
l
l
l
–5
–5
–500
–50
–200
–500
±2
±2
±50
±2
±2
±150
5
5
500
50
200
500
nA
nA
nA
nA
nA
nA
l
0
76
V
l
l
l
l
5
pF
1
3.7
MΩ
kΩ
>1
>100
GΩ
MΩ
60167fa
5
LT6016/LT6017
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified temperature
range, –55°C < TJUNCTION < 150°C for MP-grade parts, otherwise specifications are at TA = 25°C, VS = 5V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
en
Input Referred Noise Voltage Density
CONDITIONS
MIN
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
MP-GRADE
TYP
MAX
UNITS
18
25
nV/√Hz
nV/√Hz
0.5
μVP-P
0.1
11.5
pA/√Hz
pA/√Hz
Input Referred Noise Voltage
f = 0.1Hz to 10Hz
VCM < V+ – 1.75V
in
Input Referred Noise Current Density
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
AVOL
Open Loop Gain
RL = 10kΩ
ΔVOUT = 3V
l
200
3000
V/mV
PSRR
Supply Rejection Ratio
VS = ±1.65V to ±15V
VCM = VOUT = Mid-Supply
l
106
126
dB
CMRR
Input Common Mode Rejection Ratio
VCM = 0V to 3.25V
VCM = 5V to 76V
l
l
90
120
126
140
dB
dB
VOL
Output Voltage Swing Low
VS = 5V, No Load
VS = 5V, 5mA
l
l
3
280
75
550
mV
mV
VOH
Output Voltage Swing High
VS = 5V, No Load
VS = 5V, 5mA
l
l
450
1000
750
1300
mV
mV
ISC
Short-Circuit Current
VS = 5V, 50Ω to V+
VS = 5V, 50Ω to V–
l
l
8
8
25
25
mA
mA
GBW
Gain Bandwidth Product
fTEST = 10kHz
l
2.85
2.4
3.2
3.2
MHz
MHz
SR
Slew Rate
ΔVOUT = 3V
l
0.55
0.4
0.75
0.75
V/μs
V/μs
tS
Settling Time Due to Input Step
0.1% Settling
ΔVOUT = ±2V
3.5
μs
VS
Supply Voltage
Reverse Supply (Note 7)
IS < –25VμA/Amplifier
IS
Supply Current Per Amplifier
VS = 5V
RO
Output Impedance
ΔIO = ±5mA
l
l
3
3.3
l
–63
50
50
–50
V
V
V
315
315
335
540
μA
μA
0.15
Ω
The l denotes the specifications which apply over the specified temperature range, –55°C < TJUNCTION < 150°C for MP-grade parts,
otherwise specifications are at TA = 25°C, VS = ±15V, VCM = VOUT = mid-supply.
SYMBOL PARAMETER
VOSI
CONDITIONS
Input Offset Voltage
l
VS = ±25V
VS = ±25V
ΔVOSI
ΔTEMP
Input Offset Voltage Drift
IB
Input Bias Current
IOS
Input Offset Current
VCMR
Common Mode Input Range
CIN
Differential Input Capacitance
RIN
Differential Input Resistance
l
MIN
MP-GRADE
TYP
MAX
UNITS
–80
–500
–110
–500
±55
±55
±75
±75
80
500
110
500
μV
μV
μV
μV
0.75
0 < VCM < V+ – 1.75V
VCM > V+
μV/°C
l
–5
–300
±2
±2
5
300
nA
nA
l
–5
–50
±2
±2
5
50
nA
nA
l
–15
61
V
5
pF
1
3.7
MΩ
kΩ
60167fa
6
LT6016/LT6017
ELECTRICAL CHARACTERISTICS
The l denotes the specifications which apply over the specified temperature
range, –55°C < TJUNCTION < 150°C for MP-grade parts, otherwise specifications are at TA = 25°C, VS = ±15V, VCM = VOUT = Mid-Supply.
SYMBOL PARAMETER
CONDITIONS
MIN
RINCM
Common Mode Input Resistance
0 < VCM < V+ – 1.75V
VCM > V+
en
Input Referred Noise Voltage Density
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
MP-GRADE
TYP
MAX
>1
>100
UNITS
GΩ
MΩ
18
25
nV/√Hz
nV/√Hz
0.5
μVP-P
0.1
11.5
pA/√Hz
pA/√Hz
Input Referred Noise Voltage
f = 0.1Hz to 10Hz
VCM < V+ – 1.75V
in
Input Referred Noise Current Density
f = 1kHz
VCM < V+ – 1.75V
VCM > V+
AVOL
Open Loop Gain
RL = 10kΩ
ΔVOUT = 27V
l
100
1000
V/mV
PSRR
Supply Rejection Ratio
VS = ±2.5V to ±25V
VCM = VOUT = 0V
l
106
126
dB
CMRR
Input Common Mode Rejection Ratio
VCM = –15V to 13.25V
l
100
126
dB
VOL
Output Voltage Swing Low
VS = ±15V, No Load
VS = ±15V, 5mA
l
l
3
280
75
550
mV
mV
VOH
Output Voltage Swing High
VS = ±15V, No Load
VS = ±15V, 5mA
l
l
450
1000
750
1300
mV
mV
ISC
Short-Circuit Current
VS = ±15V, 50Ω to GND
VS = ±15V, 50Ω to GND
l
l
8
8
30
32
mA
mA
GBW
Gain Bandwidth Product
fTEST = 10kHz
l
2.9
2.45
3.3
3.3
MHz
MHz
SR
Slew Rate
ΔVOUT = 3V
l
0.6
0.45
0.8
0.8
V/μs
V/μs
tS
Settling Time Due to Input Step
0.1% Settling
ΔVOUT = ±2V
3.5
μs
VS
Supply Voltage
Reverse Supply
IS
IS = –25μA/Amplifier
Supply Current Per Amplifier
l
VS = ±25V
VS = ±25V
RO
Output Impedance
l
l
ΔIO = ±5mA
Note 1: Stresses beyond those listed under Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to any Absolute
Maximum Rating condition for extended periods may affect device
reliability and lifetime.
Note 2: Voltages applied are with respect to V–. The inputs are tested to
the Absolute Maximum Rating by applying –25V (relative to V–) to each
input for 10ms. In general, faults capable of sinking current from either
input should be current limited to under 10mA. See the Applications
Information section for more details.
Note 3: A heat sink may be required to keep the junction temperature
below absolute maximum. This depends on the power supply voltage and
how many amplifiers are shorted.
Note 4: The LT6016I/LT6017 are guaranteed functional over the operating
temperature range of –40°C to 85°C. The LT6016H/LT6017H are
guaranteed functional over the operating temperature range of –40°C
to 125°C. The LT6016MP/LT6017MP are guaranteed functional over the
l
3
3.3
–65
50
50
–30
V
V
V
325
325
340
340
350
575
360
600
μA
μA
μA
μA
0.15
Ω
junction temperature range of –55°C to 150°C. Junction temperatures
greater than 125°C will promote accelerated aging. The LT6016/LT6017
has a demonstrated typical performance beyond 1000 hours at TJ = 150°C.
Note 5: The LT6016I/LT6017I are guaranteed to meet specified
performance from –40°C to 85°C. The LT6016H/LT6017H are guaranteed
to meet specified performance from –40°C to 125°C. The LT6016MP/
LT6017MP are guaranteed to meet specified performance with junction
temperature ranging from –55°C to 150°C.
Note 6: Test accuracy is limited by high speed test equipment repeatability.
Bench measurements indicate the input offset current in the Over-The-Top
configuration is typically controlled to under ±50nA at 25°C and ±150nA
over temperature.
Note 7: The Reverse Supply voltage is tested by pulling 25μA/Amplifier out
of the V+ pin while measuring the V+ pin’s voltage with both inputs and V–
grounded, verifying V+ < –50V.
60167fa
7
LT6016/LT6017
TYPICAL PERFORMANCE CHARACTERISTICS
Typical Distribution of Input
Offset Voltage
Typical Distribution of Input
Offset Voltage
600
150
100
350
965 UNITS
1930 CHANNELS
300 FROM TWO RUNS
VS = ±15V
VCM = 0V
500 TA = 25°C
MS8 PACKAGE
NUMBER OF CHANNELS
VS = 5V
350 VCM = MID-SUPPLY
TA = 25°C
300 MS8 PACKAGE
1285 UNITS
250 2570 CHANNELS
FROM TWO RUNS
200
NUMBER OF CHANNELS
400 1285 UNITS
2570 CHANNELS
FROM TWO RUNS
300
200
100
50
0
–50 –40 –30 –20 –10 0 10 20 30 40 50
INPUT OFFSET VOLTAGE (μV)
0
–30 –25 –20 –15 –10 –5 0 5 10 15 20 25 30
INPUT OFFSET VOLTAGE (μV)
Typical Distribution of Over-The-Top
Input Offset Voltage
350
510 UNITS
2040 CHANNELS
300 FROM TWO RUNS
VS = 5V
VCM = 76V
TA = 25°C
MS8 PACKAGE
250
200
150
100
200
150
100
0
–50 –40 –30 –20 –10 0 10 20 30 40 50
INPUT OFFSET VOLTAGE (μV)
60167 G03
Typical Distribution of Input
Offset Voltage
NUMBER OF CHANNELS
965 UNITS
1930 CHANNELS
300 FROM TWO RUNS
250
60167 G02
60167 G01
350
VS = 5V
VCM = 5V
TA = 25°C
MS8 PACKAGE
50
Typical Distribution of Over-The-Top
Input Offset Voltage
VS = 5V
VCM = MID-SUPPLY
TA = 25°C
DJC22 PACKAGE
250
200
150
100
500
510 UNITS
450 2040 CHANNELS
FROM TWO RUNS
400
NUMBER OF CHANNELS
NUMBER OF CHANNELS
400
NUMBER OF CHANNELS
Typical Distribution of Over-The-Top
Input Offset Voltage
VS = 5V
VCM = 5V
TA = 25°C
DJC22 PACKAGE
350
300
250
200
150
100
50
50
0
–50 –40 –30 –20 –10 0 10 20 30 40 50
INPUT OFFSET VOLTAGE (μV)
50
60167 G04
60167 G06
60167 G05
Voltage Offset Shift vs Lead Free
IR Reflow
Over-The-Top Voltage Offset Shift
vs Lead Free IR Reflow
Voltage Offset Shift vs Lead Free
IR Reflow
12
14
NUMBER OF CHANNELS
24 DEVICES
16 48 CHANNELS
MS8 PACKAGE
14 VS = 5V
VCM = MID-SUPPLY
12
10
8
6
24 DEVICES
48 CHANNELS
12 MS8 PACKAGE
VS = 5V
10 VCM = 5V
10 DEVICES
VS = 5V
40 CHANNELS VCM = MID-SUPPLY
10 DJC22 PACKAGE
NUMBER OF CHANNELS
18
NUMBER OF CHANNELS
0
–100 –80 –60 –40 –20 0 20 40 60 80 100
INPUT OFFSET VOLTAGE (μV)
0
–50 –40 –30 –20 –10 0 10 20 30 40 50
INPUT OFFSET VOLTAGE (μV)
8
6
4
8
6
4
4
2
2
2
0
5 10 15 20
–20 –15 –10 –5 0
VOLTAGE OFFSET SHIFT (μV)
25
60167 G07
0
5 10 15 20
–20 –15 –10 –5 0
VOLTAGE OFFSET SHIFT (μV)
25
60167 G08
0
–25 –20 –15 –10 –5 0 5 10 15 20 25
VOLTAGE OFFSET SHIFT (μV)
60167 G09
60167fa
8
LT6016/LT6017
TYPICAL PERFORMANCE CHARACTERISTICS
Warm-Up Drift
2.5
1.5
1.0
0.5
0.0
–0.5
–1.0
–1.5
CHANNEL A
CHANNEL B
–2.5
0
1
2
3
4
TIME AFTER POWER ON (MIN)
1.5
1.0
0.5
0.0
–0.5
–1.0
–2.5
0
1
2
3
4
TIME AFTER POWER ON (MIN)
FOUR CYCLES –55°C TO 130°C
VS = 5V, VCM = MID-SUPPLY
40 CHANNELS MEASURED
MAXIMUM SHIFT
MS8 PACKAGE
MEASURED
25
TYPICAL
0 CHANNEL
–25
–50
MINIMUM SHIFT
MEASURED
WORST-CASE
CHANNEL
–75
–100
–75 –50 –25
150
VS = 5V
VCM = MID-SUPPLY
100
0
–50
–150
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
OFFSET VOLTAGE (μV)
INPUT VOLTAGE OFFSET (μV)
75
TA = –45°C
–10
–20
TA = 125°C
–30
50
25
TA = 25°C
0
TA = –45°C
–25
TA = 125°C
–50
–75
–40
–50
0.01
0.1
1
VCM (V)
10
0
–50
–150
–50 –25
100
60167 G16
0
25 50 75 100 125 150
TEMPERATURE (°C)
60167 G15
Minimum Supply Voltage
30
TA = 25°C
CHANNEL A
CHANNEL B
60167 G14
VS = 5V
0
5 UNITS, 10 CHANNELS
MS8 PACKAGE
50
Voltage Offset vs Supply Voltage
20
VS = 5V
VCM = 50V
–100
100
10
150
100
CHANNEL A
CHANNEL B
50
Voltage Offset vs Input Common
Mode Voltage
40
Over-The-Top Voltage Offset vs
Temperature
–100
0 25 50 75 100 125 150
TEMPERATURE (°C)
–25 –20 –15 –10 –5 0 5 10 15 20 25
VOLTAGE OFFSET SHIFT (μV)
60167 G12
5 UNITS, 10 CHANNELS
MS8 PACKAGE
60167 G13
50
0
5
Voltage Offset vs Temperature
VOLTAGE OFFSET (μV)
VOLTAGE OFFSET SHIFT (μV)
50
6
60167 G11
Voltage Offset Shift vs
Temperature Cycling
75
8
2
CHANNEL A
CHANNEL B
60167 G10
100
FOUR THERMAL CYCLES –55°C TO 130°C
16 TA = 25°C
20 DEVICES
14 40 CHANNELS
MS8 PACKAGE
12 VS = 5V
VCM = MID-SUPPLY
10
4
–1.5
–2.0
5
18
5 UNITS, 10 CHANNELS
MS8 PACKAGE
VOLTAGE OFFSET (μV)
–2.0
VS = 5V
VCM = 50V
2.0
NUMBER OF CHANNELS
5 UNITS, 10 CHANNELS
MS8 PACKAGE
–100
5
10
15 20 25 30 35 40 45
TOTAL SUPPLY VOLTAGE (V)
50
60167 G17
CHANGE IN INPUT OFFSET VOLTAGE OFFSET (μV)
VS = ±15V
VCM = 0V
2.0
CHANGE IN OFFSET VOLTAGE (μV)
CHANGE IN OFFSET VOLTAGE (μV)
2.5
Voltage Offset Shift vs Thermal
Cycling
Over-The-Top Warm-Up Drift
20
TA = –45°C
15
10
TA = 125°C
5
TA = 25°C
0
–5
–10
–15
–20
0
1
3
2
4
TOTAL SUPPLY VOLTAGE (V)
5
60167 G18
60167fa
9
LT6016/LT6017
TYPICAL PERFORMANCE CHARACTERISTICS
Long Term Stability of Five
Representative Units
20
5 UNITS, 10 CHANNELS
MS8 PACKAGE
2
15
1
0
–1
–2
10
5
CHANNEL A
CHANNEL B
–4
0
1
2
TIME (MONTHS)
3
TA = 125°C
TA = 85°C
TA = 25°C
TA = –45°C
TA = –55°C
0
–3
–5
–5
0.1
4
1
10
INPUT COMMON MODE VOLTAGE (V)
Input Bias Current vs Supply
Voltage
5.0
2.5
0.0
–2.5
10
0
20
30
40
SUPPLY VOLTAGE (V)
500
300
200
TA = –55°C
PARAMETRIC SWEEP IN ~25°C
INCREMENTS
100
0
0
10
20
30
40
SUPPLY VOLTAGE (V)
30
1.50
25
1.25
1.00
15
0.75
10
0.50
10
100
1000
FREQUENCY (Hz)
10k
0.25
0
100k
60167 G25
VOLTAGE NOISE DENSITY (nV/√Hz)
VOLTAGE NOISE DENSITY (nV/√Hz)
1.75
CURRENT NOISE
TA = –55°C
TA = 130°C
0
TA = 150°C
–5
TA = 25°C
–10
–15
–60
–50
–40
–30
–20
SUPPLY VOLTAGE (V)
–10
60
VS = 5V
VCM = 5V
50
50
40
40
VOLTAGE NOISE
30
30
20
20
CURRENT NOISE
10
10
0
1
10
100
FREQUENCY (Hz)
0
60167 G24
0
1000
60167 G26
CURRENT NOISE DENSITY (pA/√Hz)
35
1
5
0.1Hz to 10Hz Noise
60
CURRENT NOISE DENSITY (pA/√Hz)
2.00
0
50
NON-INVERTING OP AMP CONFIGURATION
+INA, +INB TIED TO V–
Over-The-Top Noise Density vs
Frequency
40
10
10
60167 G23
Noise Density vs Frequency
5
0.01
0.1
1
INPUT COMMON MODE VOLTAGE (V)
Reverse Supply Current vs
Reverse Supply Voltage
400
50
VOLTAGE NOISE
TA = 125°C
TA = 85°C
TA = 25°C
TA = –45°C
TA = –55°C
60167 G21
TA = 150°C
60167 G22
20
–50
0.001
100
600
SUPPLY CURRENT PER AMPLIFIER (μA)
INPUT BIAS CURRENT (nA)
7.5
–25
Supply Current vs Supply Voltage
TA = 125°C
TA = 85°C
TA = 25°C
TA = –45°C
TA = –55°C
10.0
0
60167 G20
60167 G19
12.5
INPUT BIAS CURRENT (nA)
3
25
VS = 5V
REVERSE SUPPLY CURRENT PER AMPLIFIER (μA)
4
Input Bias Current vs Input
Common Mode Voltage
VS = ±2.5V TO ±25V
TA = 25°C
NOISE VOLTAGE (100nV/DIV)
VS = 5V
INPUT BIAS CURRENT (μA)
CHANGE IN OFFSET VOLTAGE (μV)
5
Input Bias Current vs Input
Common Mode Voltage
0
2
4
6
TIME (SEC)
8
10
60167 G27
60167fa
10
LT6016/LT6017
TYPICAL PERFORMANCE CHARACTERISTICS
Output Impedance vs Frequency
PSRR vs Frequency
120
VS = ±2.5V
80
AV = +1
1
CMRR (dB)
80
AV = 100
10
60
AV = 10
1
10
100
FREQUENCY (kHz)
0
0.1
10k
1000
1
10
100
FREQUENCY (kHz)
60167 G28
157.5
GAIN (dB)
0
–10
VS = ±2.5V
CLOAD = 20pF
10
1
100
1000
FREQUENCY (kHz)
10k
–20
0.01
3.4
56
GBW
52
3.3
PM
3.2
48
3.1
44
3.0
0
Gain-Bandwidth vs Temperature
VS = ±2.5V
40
50
10
20
30
40
TOTAL SUPPLY VOLTAGE (V)
60167 G33
Channel Separation vs Frequency
4.0
140
130
40.0
ISRC = 150μA
37.5
ISRC = 0
35.0
CHANNEL SEPARATION (dB)
GAIN-BANDWIDTH (MHz)
42.5
3.5
VS = ±15V
VS = 5V
3.0
2.5
32.5
30.0
60
CLOAD = 30pF
60167 G32
Phase Margin vs Capacitive Load
45.0
180.0
10
0.1
1
FREQUENCY (kHz)
60167 G31
1000
PHASE MARGIN (DEG)
GAIN
PHASE SHIFT (DEG)
135.0
20
1V/V
0
3.5
112.5
40
30
–20
90.00
PHASE
10
10
100
FREQUENCY (kHz)
Gain Bandwidth Product and
Phase Margin vs Supply Voltage
60
100V/V
10V/V
1
60167 G30
Gain and Phase Shift vs
Frequency
50
20
0
0.1
1000
60167 G29
Closed-Loop Small Signal
Frequency Response
40
40
20
20
GAIN BANDWIDTH PRODUCT (MHz)
0
60
NEGATIVE SUPPLY
40
0.01
PHASE MARGIN (DEG)
VS = ±2.5V
POSITIVE SUPPLY
0.10
GAIN (dB)
CMRR vs Frequency
100
100
100
PSRR (dB)
OUTPUT IMPEDANCE (Ω)
1000
120
RLOAD = OPEN
RLOAD = 1kΩ
110
100
90
80
70
0
50
100
150
200
250
CAPACITIVE LOAD (pF)
300
60167 G34
2.0
–50 –25
0
25 50 75 100 125 150
TEMPERATURE (°C)
60167 G35
VS = ±15V
60
0.1
1
10
100
FREQUENCY (kHz)
1000
60167 G36
60167fa
11
LT6016/LT6017
TYPICAL PERFORMANCE CHARACTERISTICS
Settling Time to 0.1% vs Output
Step
Slew Rate vs Temperature
2.0
VS = ±2.5V
4
AV = +1
OUTPUT STEP (V)
2
1
0
–1
AV = –1
–2
RISING EDGE
1.5
AV = –1
SLEW RATE (V/μs)
3
VS = ±15V
VCM = 0V
Short-Circuit vs Temperature
40
SHORT-CIRCUIT CURRENT (mA)
5
1.0
FALLING EDGE
0.5
–3
AV = +1
20
10
0
–10
SOURCING
–20
–30
–4
–5
VS = 5V
SINKING
30
2
3
4
5
SETTLING TIME (μs)
6
0
–50 –25
7
0
60167 G37
25 50 75 100 125 150
TEMPERATURE (°C)
60167 G39
Output Saturation Voltage vs
Input Overdrive
Large Signal Transient Response
AV = 1V/V
VS = ±2.5V
CLOAD = 20pF
1000
OUTPUT SATURATION VOLTAGE (mV)
AV = 1V/V
VS = ±15
5V/DIV
25mV/DIV
0
60167 G38
Small Signal Transient Response
60167 G40
1μs/DIV
–40
–50 –25
25 50 75 100 125 150
TEMPERATURE (°C)
100
OUTPUT LOW
10
1
60167 G41
10μs/DIV
OUTPUT HIGH
VS = ±2.5V
TA = 25°C
NO LOAD
1
10
100
INPUT OVERDRIVE (mV)
1000
60167 G42
Output Saturation Voltage (VOL)
vs Load Current
Output Saturation Voltage (VOH)
vs Load Current
10k
Open-Loop Gain
200
10k
VS = ±15V
150
100
10
1
0.001
OFFSET VOLTAGE (μV)
1000
VOH (mV)
VOL (mV)
1000
100
0.01
0.1
1
SINKING LOAD CURRENT (mA)
10
60167 G43
1
0.001
RLOAD = 2kΩ
RLOAD = 10kΩ
50
0
–50
RLOAD = 1MΩ
–100
10
TA = 125°C
TA = 25°C
TA = –45°C
100
TA = 125°C
TA = 25°C
TA = –45°C
0.01
0.1
1
SOURCING LOAD CURRENT (mA)
10
60167 G44
–150
–200
–20 –15 –10 –5
0
5
10
OUTPUT VOLTAGE (V)
15
20
60167 G45
60167fa
12
LT6016/LT6017
APPLICATIONS INFORMATION
Supply Voltage
Inputs
The positive supply pin of the LT6016/LT6017 should
be bypassed with a small capacitor (typically 0.1μF) as
close to the supply pins as possible. When driving heavy
loads an additional 4.7μF electrolytic capacitor should be
added. When using split supplies, the same is true for
the V– supply pin.
Referring to the Simplified Schematic, the LT6016/LT6017
has two input stages: a common emitter differential input
stage consisting of PNP transistors Q1 and Q2 which
operate when the inputs are biased between V– and 1.5V
below V+, and a common base input stage consisting of
PNP transistors Q3 to Q6 which operate when the common
mode input is biased greater than V+ –1.5V. This results
in two distinct operating regions as shown in Figure 2.
The LT6017 consists of two dual amplifier dice assembled
in a single DFN package which share a common substrate
(V–). While the V– pins of the quad (pins 5 and 7) must
always be tied together and to the exposed pad underneath,
the V+ power supply pins (pins 16 and 18) may be supplied independently. The B and C channel amplifiers are
supplied through V+ by pin 16, and the A and D channel
amplifiers are supplied by pin 18. If pin 16 and pin 18 are
not tied together and are biased independently, each V+ pin
should have their own dedicated supply bypass to ground.
For common mode input voltages approximately 1.5V or
more below the V+ supply (Q1 and Q2 active), the common emitter PNP input stage is active and the input bias
current is typically under ±2nA. When the common mode
input is within approximately 1V of the V+ supply or higher
–50V
OK!
+
Shutdown
While there are no dedicated shutdown pins for the LT6016/
LT6017, the amplifiers can effectively be shut down into
a low power state by removing V+. In this condition the
input bias current is typically less than 1nA with the inputs
biased between V– and 76V above V–, and if the inputs are
taken below V–, they appear as a diode in series with 1k of
resistance. The output may be pulled up to 50V above the
V+ power supply in this condition (See Figure 1). Pulling
the output pin below V– will produce unlimited current
and can damage the part.
Reverse Battery
The LT6016/LT6017 are protected against reverse battery
voltages up to 50V. In the event a reverse battery condition occurs, the supply current is typically less than 5μA
(assuming the inputs are biased within a diode drop from
V–). For typical single supply applications with ground referred loads and feedback networks, no other precautions
are required. If the reverse battery condition results in a
negative voltage at the input pins, the current into the pin
should be limited by an external resistor to less than 10mA.
5V
OK!
+
–
–
+
80V
REVERSE BATTERY
TOLERANT
5V
OK!
80V
INPUTS DRIVEN ABOVE
SUPPLY TOLERANT
+
5V
OK!
+
+
–
–
–
25V
TRANSIENT
LARGE DIFFERENTIAL
INPUT VOLTAGE
TOLERANT
INPUTS DRIVEN BELOW
GROUND TOLERANT
0V
OK!
+
+
–
50V
+
60167 F01
OUTPUT DRIVEN ABOVE THE
V+ SUPPLY (IN SHUTDOWN)
TOLERANT
Figure 1. LT6016/LT6017 Fault Tolerant Conditions
60167fa
13
LT6016/LT6017
APPLICATIONS INFORMATION
The inputs are protected against temporary excursions to
as much as 25V below V– by internal 1k resistor in series
with each input and a diode from the input to the negative
supply. Adding additional external series resistance will
extend the protection beyond 25V below V–. The input
stage of the LT6016/LT6017 incorporates phase reversal
protection to prevent the output from phase reversing for
inputs below V–.
There are no clamping diodes between the inputs. The
inputs may be over-driven differentially to 80V without
damage, or without drawing appreciable input current.
Figure 1 summarizes the kind of faults that may be applied
to the LT6016/LT6017 without damage.
Over-The-Top Operation Considerations
When the input common mode of the LT6016/LT6017 is
biased near or above the V+ supply, the amplifier is said
to be operating in the Over-The-Top configuration. The
differential input pair which control amplifier operation
is common base pair Q3 to Q6 (refer to the Simplified
Schematic). If the input common mode is biased between
V– and approximately 1.5V below V+, the amplifier is said
to be operating in the normal configuration. The differential
input pair which control amplifier operation is common
emitter pair Q1 and Q2.
A plot of the Over-The-Top Transition region vs Temperature
(the region between normal operation and Over-The-Top
operation) on a 5V single supply is shown in Figure 2.
5.0
4.5
VS = 5V
4.0
3.5
VCM (V)
(Over-The-Top operation), Q9 begins to turn on diverting
bias current away from the common emitter differential
input pair to the current mirror consisting of Q11 and Q12.
The current from Q12 will bias the common base differential
input pair consisting of Q3 to Q6. Because the Over-The-Top
input pair is operating in a common base configuration,
the input bias current will increase to about, 14μA. Both
input stages have their voltage offsets trimmed tightly and
are specified in the Electrical Characteristics table.
TYPICAL COMMON MODE VOLTAGE
FOR ONSET OF OVER-THE-TOP
OPERATION
3.0
2.5
2.0
TYPICAL COMMON MODE VOLTAGE
WHERE OVER-THE-TOP OPERATION
FULLY ON
1.5
1.0
TRANSISTION REGION
0.5
0
–50
–25
0
25
75
50
TEMPERATURE (°C)
100
125
150
60167 F02
Figure 2. LT6016/LT6017 Over-The-Top Transition Region vs
Temperature
Some implications should be understood about OverThe-Top operation. The first, and most obvious is the
input bias currents change from under ±2nA in normal
operation to 14μA in Over-The-Top operation as the input
stage transitions from common emitter to common base.
Even though the Over-The-Top input bias currents run
around 14 μA, they are very well matched and their offset
is typically under ±100nA.
The second and more subtle change to amplifier operation
is the differential input impedance which decreases from
1MΩ in normal operation, to approximately 3.7kΩ in
Over-The-Top operation (specified as RIN in the Electrical
Characteristics table). This resistance appears across the
summing nodes in Over-The-Top operation and is due to
the common base input stage configuration. Its value is
easily derived from the specified input bias current flowing
into the op amp inputs and is equal to 2 • k • T/(q • Ib)
(k-Boltzmann’s constant, T – operating temperature,
Ib-operating input bias current of the amplifier in the
Over-The-Top region). And because the inputs are biased
proportional to absolute temperature, it is relatively
constant with temperature. The user may think this
effective resistance is relatively harmless because it
appears across the summing nodes which are forced
60167fa
14
LT6016/LT6017
APPLICATIONS INFORMATION
to 0V differential by feedback action of the amplifier.
However, depending on the configuration of the feedback
around the amplifier, this input resistance can boost noise
gain, lower overall amplifier loop gain and closed loop
bandwidth, raise output noise, with one benevolent effect
in increasing amplifier stability.
In the normal mode of operation (where V– < VCM < V+
–1.5V), RIN is typically large compared to the value of the
input resistor used, and RIN can be ignored (refer to Figure 3).
In this case the noise gain is defined by the equation:
R
NOISE GAIN ≈ 1+ F
RI
Normal mode: BWCLOSED − LOOP ≈
GBW
R
1+ F
RI
Over-The-Top mode:
BWCLOSED − LOOP ≈
GBW
RF
1+
RI || (RIN + RI || R F)
And output noise is negatively impacted going from normal
mode to Over-The-Top:
However, when the amplifier transitions into Over-The-Top
mode with the input common mode biased near or above
the the V+ supply, RIN should be considered. The noise
gain of the amplifier changes to:
NOISE GAIN = 1+
Likewise the closed loop bandwidth of the amplifier will
change going from normal mode operation to Over-TheTop operation:
RF
RI || (RIN + RI || R F)
Normal mode: (neglecting resistor noise)
⎛ R ⎞
eno ≈ eni • ⎜1+ F ⎟
⎝ RI ⎠
Over-The-Top mode: (neglecting resistor noise)
RF
5V
RI
VIN
VINCM
RI
+
RIN
1/2
LT6016
VOUT
⎞
⎛
RF
⎟⎟
eno ≈ eni • ⎜⎜1+
⎝ RI || (RIN + RI || R F) ⎠
–
Output
RF
60167 F03
Figure 3. Difference Amplifier Configured for Both
Normal and Over-The-Top Operation
While it is true that the DC closed loop gain will remain
mostly unaffected (= R F ), the loop gain of the amplifier
RI
A OL
A OL
RF
has decreased from 1+ R F to 1+
RI || (RIN + RI || R F)
RI
The output of the LT6016/LT6017 can swing within a
Schottky diode drop (~0.4V) of the V+ supply, and within
5mV of the negative supply with no load. The output is
capable of sourcing and sinking approximately 25mA.
The LT6016/LT6017 are internally compensated to drive
at least 200pF of capacitance under any output loading
conditions. For larger capacitive loads, a 0.22μF capacitor in series with a 150Ω resistor between the output and
ground will compensate these amplifiers to drive capacitive
loads greater than 200pF.
60167fa
15
LT6016/LT6017
APPLICATIONS INFORMATION
Distortion
In general, the die junction temperature (TJ) can be estimated from the ambient temperature TA, and the device
power dissipation PD:
There are two main contributors of distortion in op amps:
output crossover distortion as the output transitions
from sourcing to sinking current and distortion caused
by nonlinear common mode rejection. If the op amp is
operating in an inverting configuration there is no common mode induced distortion. If the op amp is operating
in the noninverting configuration within the normal input
common mode range (V– to V+ –1.5V) the CMRR is very
good, typically over 120dB. When the LT6016 transitions
input stages going from the normal input stage to the
Over-The-Top input stage or vice-versa, there will be a
significant degradation in linearity due to the change in
input circuitry.
The power dissipation in the IC is a function of supply
voltage and load resistance. For a given supply voltage,
the worst-case power dissipation PD(MAX) occurs at the
maximum supply current with the output voltage at half
of either supply voltage (or the maximum swing is less
than one-half the supply voltage). PD(MAX) is given by:
Lower load resistance increases distortion due to a net
decrease in loop gain, and greater voltage swings internal
to the amp necessary to drive the load, but has no effect
on the input stage transition distortion. The lowest distortion can be achieved with the LT6016/LT6017 sourcing in
class-A operation in an inverting configuration, with the
input common mode biased mid-way between the supplies.
PD(MAX) = 2 • 50 • 0.6mA + 2 • (12.5)2/2500 = 0.185W
Power Dissipation Considerations
Because of the ability of the LT6016/LT6017 to operate on
power supplies up to ±25V and to drive heavy loads, there
is a need to ensure the die junction temperature does not
exceed 150°C. The LT6016 is housed in an 8-lead MSOP
package (θJA = 273°C/W). The LT6017 is housed in a 22
pin leadless DFN package (DJC22, θJA = 31.8°C/W).
TJ = TA + PD • θJA
PD(MAX) = (VS • IS(MAX)) + (VS/2)2/RLOAD
Example: An LT6016 in a MSOP package mounted on a PC
board has a thermal resistance of 273°C/W. Operating on
±25V supplies with both amplifiers simultaneously driving
2.5kΩ loads, the worst-case IC power dissipation for the
given load occurs when driving 12.5VPEAK and is given by:
With a thermal resistance of 273°C/W, the die temperature
will experience approximately a 50°C rise above ambient.
This implies the maximum ambient temperate the LT6016
should ever operate under the assumed conditions:
TA = 150°C – 50°C = 100°C
To operate to higher ambient temperatures, use two channels of the LT6017 quad which has lower thermal resistance
θJA = 31.8°C/W, and an exposed pad which may be soldered
down to a copper plane (connected to V–) to further lower
the thermal resistance below θJA = 31.8°C/W.
60167fa
16
LT6016/LT6017
SIMPLIFIED SCHEMATIC
V+
Q10
PNP
R5
40k
I1
I3
I4
16μA
8μA
8μA
M2
PMOS
R1, 1k
Q9
PNP –IN
I2
R2, 1k
5μA
Q2
PNP
+IN
Q6
PNP
Q3
PNP
Q4
PNP
D3
Q5
PNP
P
CLASS AB
ADJUST
N
Q1
PNP
Q7
NPN
M1
PMOS
OUT
Q8
NPN
Q13
NPN
Q11
NPN
Q12
NPN
D1
D2
R3
6k
R4
6k
D4
V–
60167 SS
60167fa
17
LT6016/LT6017
TYPICAL APPLICATIONS
Gain of 100 High Voltage Difference Amplifier with –5V/75V Common Mode Range
CMRR
ADJUST
97.6k
5k
1k
+
VIN
–
+
VCM
–
1k
5V
+
1/2
LT6016
VOUTt7IN
–
–5V
100k
60167 TA02
60167fa
18
LT6016/LT6017
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
MS8 Package
8-Lead Plastic MSOP
(Reference LTC DWG # 05-08-1660 Rev F)
0.889 ±0.127
(.035 ±.005)
5.23
(.206)
MIN
3.20 – 3.45
(.126 – .136)
3.00 ±0.102
(.118 ±.004)
(NOTE 3)
0.65
(.0256)
BSC
0.42 ± 0.038
(.0165 ±.0015)
TYP
8
7 6 5
0.52
(.0205)
REF
RECOMMENDED SOLDER PAD LAYOUT
0.254
(.010)
3.00 ±0.102
(.118 ±.004)
(NOTE 4)
4.90 ±0.152
(.193 ±.006)
DETAIL “A”
0° – 6° TYP
GAUGE PLANE
1
0.53 ±0.152
(.021 ±.006)
DETAIL “A”
2 3
4
1.10
(.043)
MAX
0.86
(.034)
REF
0.18
(.007)
SEATING
PLANE
0.22 – 0.38
(.009 – .015)
TYP
0.65
(.0256)
NOTE:
BSC
1. DIMENSIONS IN MILLIMETER/(INCH)
2. DRAWING NOT TO SCALE
3. DIMENSION DOES NOT INCLUDE MOLD FLASH, PROTRUSIONS OR GATE BURRS.
MOLD FLASH, PROTRUSIONS OR GATE BURRS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
4. DIMENSION DOES NOT INCLUDE INTERLEAD FLASH OR PROTRUSIONS.
INTERLEAD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.152mm (.006") PER SIDE
5. LEAD COPLANARITY (BOTTOM OF LEADS AFTER FORMING) SHALL BE 0.102mm (.004") MAX
0.1016 ±0.0508
(.004 ±.002)
MSOP (MS8) 0307 REV F
60167fa
19
LT6016/LT6017
PACKAGE DESCRIPTION
Please refer to http://www.linear.com/designtools/packaging/ for the most recent package drawings.
DJC Package
22-Lead Plastic DFN (6mm w 3mm)
(Reference LTC DWG # 05-08-1714 Rev Ø)
0.889
0.70 ±0.05
R = 0.10
0.889
3.60 ±0.05
1.65 ±0.05
2.20 ±0.05 (2 SIDES)
PACKAGE
OUTLINE
0.25 ±0.05
0.50 BSC
5.35 ±0.05
(2 SIDES)
RECOMMENDED SOLDER PAD PITCH AND DIMENSIONS
NOTE:
1. DIMENSIONS ARE IN MILLIMETERS
2. APPLY SOLDER MASK TO AREAS THAT
ARE NOT SOLDERED
3. DRAWING IS NOT TO SCALE
6.00 ±0.10
(2 SIDES)
0.889
R = 0.10
TYP
3.00 ±0.10
(2 SIDES)
R = 0.115
TYP
0.40 ±0.05
12
22
0.889
1.65 ±0.10
(2 SIDES)
PIN 1
TOP MARK
(NOTE 6)
11
0.200 REF
1
0.25 ±0.05
0.50 BSC
0.75 ±0.05
0.00 – 0.05
5.35 ±0.10
(2 SIDES)
PIN #1 NOTCH
R0.30 TYP OR
0.25mm w 45°
CHAMFER
(DJC) DFN 0605
BOTTOM VIEW—EXPOSED PAD
NOTE:
1. DRAWING PROPOSED TO BE MADE VARIATION OF VERSION (WXXX)
IN JEDEC PACKAGE OUTLINE M0-229
2. DRAWING NOT TO SCALE
3. ALL DIMENSIONS ARE IN MILLIMETERS
4. DIMENSIONS OF EXPOSED PAD ON BOTTOM OF PACKAGE DO NOT INCLUDE
MOLD FLASH. MOLD FLASH, IF PRESENT, SHALL NOT EXCEED 0.15mm ON ANY SIDE
5. EXPOSED PAD SHALL BE SOLDER PLATED
6. SHADED AREA IS ONLY A REFERENCE FOR PIN 1 LOCATION
ON TOP AND BOTTOM OF PACKAGE
60167fa
20
LT6016/LT6017
REVISION HISTORY
REV
DATE
DESCRIPTION
A
01/13
Corrected Block Diagram Q7 and Q8
PAGE NUMBER
17
60167fa
Information furnished by Linear Technology Corporation is believed to be accurate and reliable.
However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights.
21
LT6016/LT6017
TYPICAL APPLICATION
Extended Supply Current Boosted Gain of Three Amplifier Drives 100Ω Load to ±30V, with 600mA Current Limit
47nF
1k
0.1μF
35V
330pF
1k
820pF
35V
20k
10k
–
100k
330Ω
1/2
LT6016**
1k
VIN
Q1
–
1/2
LT6016
1Ω
604Ω
1/2W
+
Q2
+
VOUT = ±30V
24VZ*
–35V
1k
10nF
24VZ*
–35V
47nF
2 × 1N4148
OR EQUIVALENT
*ZENER DIODES: CENTRAL SEMI CMZ5934
Q1, Q2: ON-SEMI D44VH10 NPN, D45VH10 PNP WITH HEAT SINK
**BOTH HALVES OF LT6016 ON SAME SUPPLY
60167 TA03
RELATED PARTS
PART NUMBER
DESCRIPTION
COMMENTS
LT1490A/LT1491A
Dual and Quad Micropower Rail-to-Rail Input and
Output Op amp
Over-The-Top Inputs, 50μA/Amplifier, Reverse Battery Protection to 18V
LT1638/LT1639
1.2MHz, 0.4V/μs Over-The-Top Rail-to-Rail Input and Over-The-Top Inputs, 230μA/Amplifier, 1.2MHz GBW, 0.4V/μs Slew Rate
Output Op Amp
LT1494/LT1495/LT1496
1.5μA Max, Single, Dual, and Quad, Over-The-Top
Precision Rail-to-Rail Input and Output Op Amps
Over-The-Top Inputs, 1.5μA/Amplifier, 375μV Voltage Offset
LT1112/LT1114
Dual/Quad Low Power Precision, pA Input Op Amp
60μV Offset Voltage, 400 μA/Amplifier
LT1013/LT1014
Dual/Quad Precision Op Amp
150μV Offset Voltage, 500 μA/Amplifier
60167fa
22 Linear Technology Corporation
LT 0113 REV A • PRINTED IN USA
1630 McCarthy Blvd., Milpitas, CA 95035-7417
(408) 432-1900 ● FAX: (408) 434-0507
●
www.linear.com
© LINEAR TECHNOLOGY CORPORATION 2012