SP5055 2.6GHz Bidirectional I2C BUS Controlled Synthesiser Supersedes version in April 1994 Consumer IC Handbook, HB3120 - 2.0 DS2384 - 4.4 May 1996 The SP5055 is a single chip frequency synthesiser designed for TV tuning systems. Control data is entered in the standard I2C BUS format. The device contains 4 addressable current limited outputs and 4 addressable Bi-Directional open collector ports one of which is a 3 bit ADC. The information on these ports can be read via the I2C BUS. The device has one fixed I2C BUS address and 3 programmable addresses, programmed by applying a specific input voltage to one of the current limited outputs. This enables 2 or more synthesisers to be used in a system. FEATURES ■ Complete 2.6GHz Single Chip System ■ Programmable via I2C BUS ■ Low power consumption (5V 65mA) ■ Low Radiation ■ Phase Lock Detector ■ Varactor Drive Amp Disable ■ 6 Controllable Outputs, 4 Bi-Directional ■ 5 Level ADC ■ Variable I2C BUS Address For Multi Tuner Applications ■ Full ESD Protection* * Normal ESD handling procedures should be observed. Fig. 1 Pin connections – top view APPLICATIONS ■ Satellite TV ■ High IF Cable Tuning Systems ORDERING INFORMATION SP5055S MP - (16 lead Miniature Plastic package) SP5055 ELECTRICAL CHARACTERISTICS Tamb = -20°C to +80°C, VCC = +4.7V to 5.3V. These Characteristics are guaranteed by either production test or design. They apply within the specified ambient temperature and supply voltage unless otherwise stated. Reference frequency = 4MHz unless otherwise stated. Value Characteristic Pin Units Conditions Typ. Min. Max. Supply current Prescaler input voltage Prescaler input voltage 12 13, 14 13, 14 Prescaler input impedance Prescaler input capacitance 13, 14 SDA, SCL Input high voltage Input low voltage Input high current Input low current Leakage current SDA Output voltage Charge pump current low Charge pump current high Charge pump output leakage current Charge pump drive output current Charge pump amplifier gain Recommended crystal series resistance Crystal oscillator drive level Crystal oscillator negative resistance 4, 5 4, 5 4, 5 4, 5 4, 5 1 1 1 16 80 300 300 3 0 mA VCC = 5V mVRMS 500MHz to 2.6GHz Sinewave mVRMS 120MHz, see Fig. 5 Ω pF 50 2 4 5.5 1.5 10 -10 10 V V µA µA µA Input voltage = VCC Input voltage = 0V When VCC = 0V 0.4 V Isink = 3mA µA µA nA µA Byte 4, bit 2 = 0, pin 1 = 2V Byte 4, bit 2 = 1, pin 1 = 2V Byte 4, bit 4 = 1, pin 1 = 2V Vpin 16 = 0·7V ±50 ±170 ±5 500 6400 10 2 2 Output Ports P0, P3 sink current P0, P3 leakage current P4-P7 sink current P4-P7 leakage current 10, 11 10, 11 9-6 9-6 Input Ports P3 input current high P3 input current low P4,P5,P7 input voltage low P4,P5,P7 input voltage high P6 input current high P6 input current low 10 10 9,8,6 9,8,6 7 7 2 65 50 100 200 Ω mVp-p Ω 1.5 10 mA µA mA µA VOUT = 12V VOUT = 13·2V VOUT = 0.7V VOUT = 13·2V µA µA V V µA µA Vpin 10 = 13.2V Vpin 10 = 0V 80 750 0.7 1 10 10 +10 -10 0.8 2.7 +10 -10 See Table 3 for ADC Levels SP5055 Fig. 2 Block diagram FUNCTIONAL DESCRIPTION The SP5055 is programmed from an I2 C BUS. Data and Clock are fed in on the SDA and SCL lines respectively as defined by the I 2C BUS format. The synthesiser can either accept new data (write mode) or send data (read mode). The Tables in Fig. 3 illustrate the format of the data. The device can be programmed to respond to several addresses, which enables the use of more than one synthesiser in an I 2C Bus system. Table 4 shows how the address is selected by applying a voltage to P3. The last bit of the address byte (R/W) sets the device into read mode if it is high and write mode if it is low. When the SP5055 receives a correct address byte it pulls the SDA line low during the acknowledge period and during following acknowledge periods after further data bytes are programmed. When the SP5055 is programmed into the read mode the controlling device accepting the data must pull down the SDA line during the following acknowledge period to read another status byte. WRITE MODE (FREQUENCY SYNTHESIS) When the device is in the write mode Bytes 2 + 3 select the synthesised frequency while bytes 4 + 5 select the output port states and charge pump information. Once the correct address is received and acknowledged, the first Bit of the next Byte determines whether that byte is interpreted as byte 2 or 4, a logic 0 for frequency information and a logic 1 for charge pump and output port information. Additional data bytes can be entered without the need to re-address the device until an I2C stop condition is recognised. This allows a smooth frequency sweep for fine tuning or AFC purposes. If the transmission of data is stopped mid-byte (i.e., by another device on the bus) then the previously programmed byte is maintained. Frequency data from bytes 2 and 3 is stored in a 15-bit shift register and is used to control the division ratio of the 15-bit programmable divider which is preceded by a divide-by-16 prescaler and amplifier to give excellent sensitivity at the local oscillator input; see Fig 5. The input impedance is shown in Fig 7. The programmed frequency can be calculated by multiplying the programmed division ratio by 16 times the comparison frequency F comp. When frequency data is entered, the phase comparator, via the charge pump and varactor drive amplifier, adjusts the local oscillator control voltage until the output of the programmable divider is frequency and phase locked to the comparison frequency. The reference frequency may be generated by an external source capacitively coupled into pin 2 or provided by an onboard 4MHz crystal controlled oscillator. Note that the comparison frequency is 7·8125kHz when a 4MHz reference is used. Bit 2 of byte 4 of the programming data (CP) controls the current in the charge pump circuit, a logic 1 for ±170µA and a logic 0 for ±50µA, allowing compensation for the variable tuning slope of the tuner and also to enable fast channel changes over the full band. Bit 4 of byte 4 (T0) disables the charge pump if set to a logic 1. Bit 8 of byte 4 (OS) switches the charge pump drive amplifier’s output off when it is set to a logic 1. Bit 3 of Byte 4 (T1) selects a test mode where the phase comparator inputs are available on P6 and P7, a logic 1 connects F comp to P6 and F div to P7. Byte 5 programs the output ports P0 to P7; on a logic 0 for a high impedance output, logic 1 for low impedance (on). READ MODE When the device is in the read mode the status data read from the device on the SDA line takes the form shown in Table 2. Bit 1 (POR) is the power-on reset indicator and is set to a logic 1 if the power supply to the device has dropped below 3V and the programmed information lost (e.g., when the device is initially turned on). The POR is set to 0 when the read sequence is terminated by a stop command. The outputs are all set to high impedance when the device is initially powered up. Bit 2 (FL) indicates whether the device is phase locked, a logic 1 is present if the device is locked and a logic 0 if the device is unlocked. 3 SP5055 Bits 3, 4 and 5 (I2,I1,I0) show the status of the I/O Ports P7, P5 and P4 respectively. A logic 0 indicates a low level and a logic 1 a high level. If the ports are to be used as inputs they should be programmed to a high impedance state (logic 1). These inputs will then respond to data complying with TTL type voltage levels. Bits 6, 7 and 8 (A2,A1,A0) combine to give the output of the 5 level ADC. The 5 level ADC can be used to feed AFC information to the microprocessor from the IF section of the receiver, as illustrated in the typical application circuit. APPLICATION A typical Application is shown in Fig. 4. All input/output interface circuits are shown in Fig. 6. MSB Address LSB 1 1 0 0 0 Programmable divider 0 14 13 12 11 Programmable divider 7 2 2 Charge pump and test bits 1 P7 I/O port control bits 2 6 2 5 2 2 MA1 MA0 10 2 9 2 1 0 A Byte 1 8 A Byte 2 0 2 2 4 2 3 2 2 2 2 2 A Byte 3 CP T1 T0 1 1 1 OS A Byte 4 P6 P5 P4 P3 X X P0 A Byte 5 1 A Byte 1 A0 A Byte 2 Table 1 Write data format (MSB transmitted first) Address 1 1 Status byte POR FL 0 0 0 I2 I1 I0 MA1 MA0 A2 A1 Table 2 Read data format (MSB is transmitted first) A MA1, MA0 CP T1 T0 OS P7, P6, P5, P4, P3, P0 POR FL I2, I1, I0 A2, A1, A0 X : : : : : : : Acknowledge bit Variable address bits (see Table 4) Charge Pump current select Test mode selection Charge pump disable Varactor drive Output disable Switch Control output states : : : : : Power On Reset indicator Phase lock detect flag Digital information from Ports P7, P5 and P4, respectively 5 Level ADC data from P6 (see Table 3) Don't care A2 A1 A0 Voltage input to P6 1 0 0 0.6VCC to 13.2V 0 0 0V to 0·2VCC 0 1 1 0·45VCC to 0·6VCC 0 1 Always valid 0 1 0 0·3VCC to 0·45VCC 1 0 0·3VCC to 0·7VCC 0 0 1 0·15VCC to 0·3VCC 1 1 0·8VCC -13.2V 0 0 0 0 to 0.15VCC Table 4 Address selection Table 3 ADC levels Fig. 3 Data formats 4 MA1 MA0 Voltage input to P3 SP5055 APPLICATION A typical application is shown in Fig. 4. All input/output interface circuits are shown in Fig. 6. Fig. 4 Typical application Fig. 5 Typical input sensitivity 5 SP5055 Fig. 6 SP5055 Input/output interface circuits 6 SP5055 Fig. 7 Typical input impedance ABSOLUTE MAXIMUM RATINGS All voltages are referred to VEE and pin 3 at 0V Parameter Supply voltage RF input voltage Pin 12 Units Min. Max. -0.3 7 V 2.5 Vp-p 14 6 14 V V V 13, 14 Port voltage 6-11 6-9 10, 11 Total port output current 6-11 RF input DC offset Value -0.3 -0.3 -0.3 50 -0.3 VCC+0.3 V Charge pump DC offset 1 -0.3 VCC+0.3 V Drive DC offset 16 -0.3 VCC+0.3 V Crystal oscillator DC offset 2 -0.3 VCC+0.3 V 4, 5 -0.3 -0.3 VCC+0.3 5.5 V V -55 +125 °C Junction temperature +150 °C MP 16 Thermal resistance, chip-to-ambient MP 16 Thermal resistance, chip-to-case 111 41 °C/W °C/W Power consumption at 5.5V 440 mW Storage temperature Port in off state Port in on state Port in on state mA 13, 14 SDA, SCL input voltage Conditions With VCC applied VCC not applied All ports off 7 http://www.mitelsemi.com World Headquarters - Canada Tel: +1 (613) 592 2122 Fax: +1 (613) 592 6909 North America Tel: +1 (770) 486 0194 Fax: +1 (770) 631 8213 Asia/Pacific Tel: +65 333 6193 Fax: +65 333 6192 Europe, Middle East, and Africa (EMEA) Tel: +44 (0) 1793 518528 Fax: +44 (0) 1793 518581 Information relating to products and services furnished herein by Mitel Corporation or its subsidiaries (collectively “Mitel”) is believed to be reliable. However, Mitel assumes no liability for errors that may appear in this publication, or for liability otherwise arising from the application or use of any such information, product or service or for any infringement of patents or other intellectual property rights owned by third parties which may result from such application or use. Neither the supply of such information or purchase of product or service conveys any license, either express or implied, under patents or other intellectual property rights owned by Mitel or licensed from third parties by Mitel, whatsoever. Purchasers of products are also hereby notified that the use of product in certain ways or in combination with Mitel, or non-Mitel furnished goods or services may infringe patents or other intellectual property rights owned by Mitel. This publication is issued to provide information only and (unless agreed by Mitel in writing) may not be used, applied or reproduced for any purpose nor form part of any order or contract nor to be regarded as a representation relating to the products or services concerned. The products, their specifications, services and other information appearing in this publication are subject to change by Mitel without notice. No warranty or guarantee express or implied is made regarding the capability, performance or suitability of any product or service. Information concerning possible methods of use is provided as a guide only and does not constitute any guarantee that such methods of use will be satisfactory in a specific piece of equipment. It is the user’s responsibility to fully determine the performance and suitability of any equipment using such information and to ensure that any publication or data used is up to date and has not been superseded. Manufacturing does not necessarily include testing of all functions or parameters. These products are not suitable for use in any medical products whose failure to perform may result in significant injury or death to the user. All products and materials are sold and services provided subject to Mitel’s conditions of sale which are available on request. M Mitel (design) and ST-BUS are registered trademarks of MITEL Corporation Mitel Semiconductor is an ISO 9001 Registered Company Copyright 1999 MITEL Corporation All Rights Reserved Printed in CANADA TECHNICAL DOCUMENTATION - NOT FOR RESALE