SPECIFICATION FOR APPROVAL REF : 20080804-B PROD. NAME PAGE: 1 ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR SU4011□□□□L□-□□□ ABC'S ITEM NO. Ⅰ﹒CONFIGURATION & DIMENSIONS： B 100 A : 4.30±0.20 m/m B : 4.50±0.20 m/m C : 1.10±0.15 m/m D : 1.50 typ m/m E : 0.50 typ m/m F : 3.30 typ m/m G : 1.70 ref m/m H : 5.30 ref m/m I : 1.00 ref m/m J : 3.30 ref m/m I ( PCB Pattern suggestion ) Ⅱ﹒SCHEMATIC DIAGRAM： a Ⅲ﹒MATERIALS： c b d e a﹒Core：Ferrite DR core b﹒Core：Ferrite RI core c﹒Wire ：Enamelled copper wire (class F & H) d﹒Adhesive ：Epoxy resin e﹒Terminal：Ag/Ni/Sn f﹒Remark：Products comply with RoHS' requirements Peak Temp：260℃ max. Max time above 230℃ ：50sec max. Max time above 200℃ ：70sec max. Temperature Rising Area Preheat Area +4.0℃ / sec max. 150 ~ 200℃ / 60 ~ 120sec Reflow Area Forced Cooling Area +2.0 ~ 4.0℃ -(1.0 ~ 5.0)℃ / sec max. / sec max. Peak Temperature: 260℃ 250 a﹒Temp. rise ：30℃ typ. b﹒Rated current： Base on temp. rise & △L / L0A=35% typ. c﹒Storage temp.：-40℃ ----+125℃ d﹒Operating temp.：-40℃----+105℃ e﹒Resistance to solder heat：260℃.10 secs. AR-001A 50sec max. Temperature ( ℃ ) Ⅳ﹒GENERAL SPECIFICATION： 230℃ 200 150 70sec max. 100 50 0 50 100 150 Time ( seconds ) 200 250 SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. NAME PAGE: 2 ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR SU4011□□□□L□-□□□ ABC'S ITEM NO. Ⅴ﹒ ELECTRICAL CHARACTERISTICS： 8.0 8.0 8.0 16.0 Test Freq. ( Hz ) L Q 100K 7.96M 100K 7.96M 100K 7.96M 100K 2.52M 70 100 150 230 92 130 230 300 95 12.0 12.0 100K 100K 350 420 460 680 Q Inductance ( μH ) ref. SU40113R0YL□-□□□ SU40114R7YL□-□□□ SU40116R8YL□-□□□ SU4011100YL□-□□□ 3.0 ± 30 ％ 4.7 ± 30 ％ 6.8 ± 30 ％ 10.0 ± 30 ％ SU4011150YL□-□□□ SU4011220YL□-□□□ 15.0 ± 30 ％ 22.0 ± 30 ％ DWG No. 1)﹒ ：Packaging Information... A ：Bulk 2.52M 2.52M SRF RDC Irms Isat ( MHz ) ( mA ) ( mA ) ( mΩ ) typ. max. typ. typ. typ. 1150 70 54 40 1700 1250 1050 820 34 22 650 580 480 420 □□□ B ：Taping Reel 2)﹒"":Reference code 3)﹒Inductance Test Freq.：100KHz / 0.1V 4)﹒Isat base on △L / L0A=35% typ. 5)﹒Irms base on Temp. rise 30℃ typ. @ Inductance VS. DC Current Curve 10 2 7 5 Inductance（uH） 3 2 220 10 1 7 5 100 6R8 3 3R0 2 10 0 7 5 3 2 10 -1 10 -2 2 3 5 7 10 -1 2 3 5 7 10 0 DC Current (A) AR-001A 2 3 5 7 10 1 940 760 610 SPECIFICATION FOR APPROVAL PAGE: 3 20080804-B REF : 20070329-A PROD. ABC'S DWG NO. SHIELDED SMD POWER INDUCTOR NAME SU4011□□□□L□-□□□ ABC'S ITEM NO. Ⅵ﹒PACKAGING INFORMATION： ( 1 ) Configuration T Cover tape N B A 2.0±0.5 ∮C ∮C D G Embossed carrier ※ Carrier tape width : D 4 m/m P:8 m/m Stary End 100 100 Leadr no component 200 m/m min. 100 100 Trailer no component 400 m/m min. Components User direction of feed ( 2 ) Dimensions Unit:m/m Style A B C D G N T 07 - 12 178 21±0.8 13 12 14 +0 50 -0 16.5 ( 3 ) Q'TY & G.W. Per package Inner : Reel Outer : Carton Series SU4011 AR-001A Q'TY (pcs) G.W. (gw) Style Q'TY (pcs) G.W. (Kg) Size (cm) 1,500 180 07 - 12 60,000 8.00 42 x 41 x 24 SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. NAME PAGE: 4 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. SU4011□□□□L□-□□□ ABC'S ITEM NO. Ⅶ﹒DWGING NUMBER EXPRESSION： S U 4 0 1 1 Reference code Appendix code 2 : Package Appendix code 1 : Classification Tolerance code Electrical code Dimension code Type code Appendix code 1：Product Classification L：Lead Free Standard products comply with RoHS' requirements 1 ~ 9：Lead Free Special products comply with RoHS' requirements Appendix code 2：Package Information Code AR-001A Inner package A T.B.D. B T / R ( Reel package ) Inner package Q'TY T.B.D. 1,500 pcs Remark SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. NAME PAGE: 5 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. SU4011□□□□L□-□□□ ABC'S ITEM NO. Ⅷ﹒RELIABILITY TEST： Test item Solderability Thermal shock test ( Temp. cycle ) Specification Test condition More than 95% of the terminal electrode Shall be covered With fresh solder. Preheat : 155 ℃ / 4 hours. Solder : Sn96.5 / Ag3 / Cu0.5 or equivalent Solder temp. : 235±5℃ Flux : Rosin Dip time : 5±0.5 seconds Electrical oharacteristics shall not change more than ±20% Room temp. 15 minutes -40 ℃ 30 minutes Room temp. 15 minutes +105 ℃ Total : 50 cycles Humidity test Temperature : 40±2℃ Humidity : 90±5% Time : 1000 hours High temp. Resistance test Temperature : 105±5℃ Applied current : Per spec. Time : 96 hours AR-001A 30 minutes SPECIFICATION FOR APPROVAL 20080804-B REF : 20070329-A PROD. NAME PAGE: 6 SHIELDED SMD POWER INDUCTOR ABC'S DWG NO. SU4011□□□□L□-□□□ ABC'S ITEM NO. Ⅸ﹒UL CARD： August 27, 1999 OBMW2 Magnet Wire-Comporent ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Mark Dsg BC Estersol 160 E180 Amldester 200 Polysol-N 155 A200 PN155 Polyesterimide (solderable) Polyesterimide Polyurechane Polysol 155 P155 Polyurechane Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ E143312 Temp Class MW-77 180 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ 200 155, 100 155, 130 130 155 155 155 156 180 Marking：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A SPECIFICATION FOR APPROVAL PAGE: 7 REF :20080804-B PROD. NAME SHIELDED SMD POWER INDUCTOR OBMW2 Magnet Wire-Comporent ABC'S DWG NO. SU4011□□□□L□-□□□ ABC'S ITEM NO. August 27, 1999 E143312 ELEKTRISOLA (MALAYSLA) SDN BHD IALAN DAMN SATU IANDA BAIK 28750 BENTONG, PAHANG DARUL MAKMUR MALAYSIA Coating Type Mtl Dsg Mark Dsg BC Estersol 160 E180 Amldester 200 Polysol-N 155 A200 PN155 Polyesterimide (solderable) Polyesterimide Polyurechane Polysol 155 P155 Polyurechane Polysol 155g Polysol 155p Polysol 160 Polysol 180 Polysol 170 Polysol-N 180 Pg155 Pp155,Gp155 P160 P180 P170 or G170 PN180 Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane Polyurechane OC ____ ____ Nylon ____ ____ ____ ____ ____ ____ Nylon ANSI Typ Temp Class MW-77 180 MW-74 MW-80, MW-28 MW-79, MW-79 MW-79 MW-79 MW-79 MW-79 MW-79 ____ 200 155, 100 155, 130 130 155 155 155 156 180 Marking：Dompany name/nateriel designation or marked designation and factory identification on package ok reel See General Information preceding These Recognitions For use only in equipment where the acceptability of the combination is determined by Underwriters Laboratories Inc. AR-001A