CHINASEMI CSLR-U319HR4-B0

CHINA
SEMICONDUCTOR
CORPORATION
Spec. No.
Rev.
PS-LL-U319HR4-B0
A
PRODUCT SPECIFICATION
Model No:
:CSLR-U319HR4-B0
Descriptions:
■LED Type
: Lighting LED Lamp
■LED Package : Round LED Lamp
■Emitting Color:Red
■Viewing Angle:50°
■No Stopper
CUSTOMER
APPROVED
SIGNATURES
APPROVED BY
CHECKED BY
PREPARED BY
CHINA SEMICONDUCTOR CORPORATION
Address:2FL. NO.909,Chung-Cheng Road,
Chung-Ho City Taipei Hsien,Taiwan.
OPTO PLUS TECHNOLOGIES CO.,LTD
Address:696 Shun jiang Rd.,Ji Shan St.Shaoxing,
ZheJiang,China
Tel:886-2-2223-9696
Fax:886-2-2223-9377
Tel:86-0575-88623888
Fax:86-0575-88623112
http://www.csctw.com.tw
CHINA
SEMICONDUCTOR
CORPORATION
Spec. No.
Rev.
PS-LL-U319HR4-B0
A
Model No:
:CSLR-U319HR4-B0
■ Features 1. Low Power Consumption.
2. High Luminous Output
3. High Reliability and Solid Performance
4. Optimal Optical/Mechanical Design
5. Rohs Compliant
■ Device Selection Guide Chip
Part No.
LED Lens
CSLR-U319HR4-B0
Material
Emitted Color
AlInGaP
Red
Water Transparent
■ Package Outline Dimensions -
0.01
*Tolerance:± 0.25
Unit:±
inch
mm
http://www.csctw.com.tw
Page:
1/5
CHINA
SEMICONDUCTOR
CORPORATION
Spec. No.
PS-LL-U319HR4-B0
Rev.
A
Model No:
:CSLR-U319HR4-B0
■ Absolute Maximum Rating (Ta=25℃)
Parameter
Symbol
Rating
Unit
Pd
52
mW
IF
30
mA
Peak Forward Current *
IFP
100
mA
Reverse Voltage
VR
5
V
Operating Temp.
Topr
-30 ~ +80
℃
Storage Temp.
Tstg
-40 ~ +100
℃
Lead Soldering Temperature
Tsol
Power Dissipation
Forward Current (DC)
Max. 260℃
℃ for 5 sec Max.
(3mm from the epoxy body)
* Pulse width ≦0.1 msec. duty ≦1/10
■ Electro-optical Characteristics
(Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Forward Voltage
VF
-----
2.1
2.6
V
Luminous Intensity
IV
1800
3800
-----
mcd
Condition
IF=20mA
Dominant Wavelength
Viewing Angle
Reverse Current
λD
-----
625
-----
nm
2θ
θ 1/2
-----
50
-----
deg
IR
-----
-----
50
μA
http://www.csctw.com.tw
VR=5V
Page:
2/5
CHINA
SEMICONDUCTOR
CORPORATION
Spec. No.
Rev.
PS-LL-U319HR4-B0
A
Model No:
:CSLR-U319HR4-B0
■ Luminous Intensity Rank Limits ( IF = 20mA )
unit:mcd
Part No.
CSLR-U319HR4-B0
min.
1800
2300
3000
3900
5100
Code
Q
R
S
T
U
max.
2300
3000
3900
5100
6600
■ Dominant Wavelength Rank Limits ( IF = 20mA )
unit:nm
Part No.
CSLR-U319HR4-B0
min.
620
625
630
Code
R1
R2
R3
max.
625
630
635
■ Forward Voltage Rank Limits ( IF = 20mA )
unit:v
Part No.
Code
B
C
D
E
F
CSLR-U319HR4-B0
min.
1.6
1.8
2.0
2.2
2.4
max.
1.8
2.0
2.2
2.4
2.6
Notes:
1.
2.
3.
4.
5.
6.
7.
Tolerance of measurement of luminous intensity
:±15%
Tolerance of measurement of Color Coordinates
:±0.01
Tolerance of measurement of forward voltage
:±0.05v
All data are measured by CSC's test equipment.
One delivery will include several color rank, VF rank and Iv ranks of the products.
The quantity-ratio of the ranks is decided by CSC.
Please confirm with CSC salesman,if your request different form standard specification.
http://www.csctw.com.tw
Page:
3/5
CHINA
SEMICONDUCTOR
CORPORATION
Spec. No.
PS-LL-U319HR4-B0
Rev.
A
Model No:
:CSLR-U319HR4-B0
■ Typical Electrical / Optical Charateristics Curves -
1
1.0
0.5
0
550
600
650
700
Relative Luminosity
Relative Intensity @ 20mA
(Ta = 25℃
℃ Unless Otherwise Noted)
0.5
0
-90°-60°-30°
0° -30°-60° -90°
Radiation Angle
Wavelength (nm)
Fig 5. Relative Intensity Vs. Wavelength
Fig 6. Relative Luminous Intensity vs.Radiation Angle
http://www.csctw.com.tw
Page:
4/5
CHINA
SEMICONDUCTOR
CORPORATION
Spec. No.
Rev.
PS-LL-U319HR4-B0
A
Model No:
:CSLR-U319HR4-B0
■ Precautions For Use 1. Recommended Soldering conditions
Wave Soldering
Temperature(°C)
260(max.)
250
240
Preheat
105(max.)
0
5 sec.
Max. 60sec.
Time(sec.)
2. Soldering Iron
Basic SPEC. is ≦5sec. When 260℃. If temperature is higher, time should
be shorter (+10℃→ -1sec.). Power dissipation of iron should be smaller than 15W
, and temperature should be controllable. Surface temperature of the device should
be under 230℃.
3. Static Electricity
a. Static electricity or surge voltage damages LEDs..
It is recommended that a wrist band or an anit-electrostatic glove be used
when handling the LEDs.
b. All devices, equipment and machinery must be properly grounded. It is
recommended that mesures be taken against surge voltage to the equipment
that mounts the LEDs.
Note: The specifications are subject to change without notice. Please contact us for updated information.
http://www.csctw.com.tw
Page:
5/5