OPTICOMM FMV

FMV-603
Duplex V /Duplex 2A & D
Two-way Video with Two Audio and
One Data for PTZ Control
The FMV-603 is a duplex Video
transmission system with two
duplex Audio ports and a single
duplex Data port, ideal for CCTV
cameras, PTZ video conferencing,
and ITS. Status indicators on Video,
Sync, FM Data, carrier detect, voltage,
temperature, and optical levels are
monitored via LEDs.
Video
Audio
System Design
Data
All of our units come as an Insert Card
version. The cards can be inserted into
our 18-slot, 19” rackmountable card
cage (CC-18-80W), or one of our smaller
Desk Top Card Racks (DTCR series).
The Desk Top Card Racks can handle
one, two, four, or seven cards, allowing
for greater flexibility and future
expansion. They can sit on a flat
surface as a larger stand-alone unit, or
can be surface mounted with the
flanges provided. Each one of our card
housings operates with an appropriate
power supply. The regulated switching
power supply has short circuit
protection and an input operating
voltage of 87- 264 VAC.
865
1310
●
●
●
●
●
1550
Type
Mode
Wavelength
Suffix
LED
MM
L0/L1
Features
• Multimode or singlemode operation over one fiber
• 8 MHz video bandwidth
• 10 Hz to 20 KHz audio bandwidth
• True DC restoration
• Flat frequency response
• Complies with RS-170 and RS-170A EIA video standards
• Compatible with NTSC, PAL and SECAM
• No EMI or RFI and no ground loops
• Stand Alone or Rack Mount
• Ideal for CCTV cameras, PTZ video conferencing,
and ITS
Fiber
Type
50 /125µ
Output
Power
Receiver
Sensitivity
Optical
Loss
Budget
Range*
Conn
Type
-16 dBm
-34 dBm
18 dB
3 km
ST
-10 dBm
-34 dBm
24 dB
25 km
FC
62.5/125µ
●
Laser
SM
L2/L3
09/125µ
* Chromatic dispersion should be taken into account.
98
800-867-8426 • [email protected] • www.opticomm.com • Contact factory for higher requirement.
CCTV Security
Networking
Video
Video in/out impedance
Video in/out level
Video bandwidth
Differential gain
Differential phase
Linearity/Tilt
Compatibility
Signal to noise ratio
FM carrier frequency
Connector type
75 Ω
1 volt peak to peak, 1.5 volts max
5 Hz to 8 MHz @ -3dB
< 1.0 % typical
< 1.0° typical
± 1.1 % typical/≤ 0.5 % typical
NTSC, PAL, SECAM, RS-170, RS-170A
>67 dB using RS-250C standards @ 1 km
70 MHz
BNC
Audio
Audio in/out impedance
Audio in/out level
Frequency response
Signal to noise ratio
Total harmonic distortion
Connector type
600 Ω (balanced) or 10 kΩ (unbalanced)
-6 to +6 dBm
10 Hz to 20 KHz
> 60 dB
< 1.0 %, 1 KHz at maximum modulation
Hi-density 15 pin DB9 (DE15)
Data
Data rate
Bit error rate
Data formats available
Connector type
General
Dimensions & Weight
Temperature
Humidity
Operating voltage
Vibration/Shock
Diagnostics
Status monitoring
DC to 300 Kbps
10-9
Async Rs-232, RS-422, RC-485/2W, Glenlock, Manchester,
20 mA current loop, TTL, or six Contact Closures
Hi-density 15 pin DB9 (DE15)
Stand Alone (SA): 7.16” L x 6.51” W x 1.75” H 53 oz
Insert Card (IC): 6.3” L x 1.7” W x 4.0” H
29 oz
Operating: -40° C to +74° C; Storage; -55° C to +85° C
0 to 95% non-condensing
9 VDC (300 mA) or 110/220 VAC
Up to 5 g's/Up to 12 g's
LED indicator
Selection Guide
Digital Broadcast
AM/IM Analog
SWFM
SWFM Analog
Analog
Analog-to-Digital
RGB Video
Datacom
RF CATV
Appendix
Opticomm
reserves the
right to change
product
specifications
without notice.
Emissions: FCC Part 15, ICES-003,
AS/NZS, 3548, EN55022
Immunity: ENVS0204,
EN61000-4-2,3,4,5,6,11
Safety:
UL1950, CAN/CSA 22.2,
NO.950-95
MADE IN THE USA
Sample Configuration
99