SHOULDER HDBF07006A62

规格书编号
SPEC NO :
产品规格书
SPECIFICATION
CUSTOMER 客 户:
PRODUCT 产 品:
SAW FILTER
MODEL NO 型 号:
HDBF07006A62
SF6-2
PREPARED 编 制:
CHECKED 审 核: Houshihong
APPROVED 批 准: CHARLES
D A T E 日 期: 2007-01-25
客户确认 CUSTOMER RECEIVED:
审核 CHECKED
批准 APPROVED
日期 DATE
无锡市好达电子有限公司
Shoulder Electronics Limited
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 1 of 6
SAW FILTER
HDBF07006A62
更改历史记录
History Record
更改日期
Date
www.shoulder.cn
规格书编号
Spec No
产品型号
Part No
客户产品型号
Customer No
Tel:0755-82916880
Fax:0755-82916881
更改内容描述
Modify Content
E-mail:[email protected]
备注
Remark
Page 2 of 6
SAW FILTER
HDBF07006A62
1. SCOPE
This specification shall cover the characteristics of SAW filter BF07006A62
2. ELECTRICAL SPECIFICATION
DC Voltage VDC
AC Voltage Vpp
Operation temperature
Storage temperature
RF Power Dissipation
10V
10V50Hz/60Hz
-10℃ to +60℃
-40℃ to +85℃
0dBm
Electronic Characteristics
Fo = 70.0 MHz
Terminating source impedance: 50 ohm and matching network
Terminating load impedance: 50 ohm and matching network
Minimum Typical
Center Frequency
MHz
Insertion Loss
dB
1dB Bandwidth
40dB Bandwidth
MHz
MHz
Passband variation
Ultimate Rejection
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
Maximum
69.85
70.0
70.15
-
19.8
20.0
6
-
6.25
8.78
9
dB
-
0.7
0.8
dB
50
55
-
E-mail:[email protected]
Page 3 of 6
SAW FILTER
HDBF07006A62
3. DIMENSION
4.TEST CIRCUIT
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 4 of 6
SAW FILTER
HDBF07006A62
5. ENVIRONMENTAL CHARACTERISTICS
5-1 High temperature exposure
Subject the device to +85℃ for 16 hours. Then release the filter into the room conditions for 24
hours prior to the measurement. It shall fulfill the specifications in table 1.
5-2 Low temperature exposure
Subject the device to -20℃ for 16 hours. Then release the device into the room conditions for 24
hours prior to the measurement. It shall fulfill the specifications in table 1.
5-3 Temperature cycling
Subject the device to a low temperature of -40℃for 30 minutes. Following by a high temperature of
+80℃ for 30 Minutes. Then release the device into the room conditions for 24 hours prior to the
measurement. It shall meet the specifications in table 1.
5-4 Resistance to solder heat
Dip the device terminals no closer than 1.5mm into the solder bath at 260℃ ±10℃ for 10±1 sec.
Then release the device into the room conditions for 4 hours. The device shall meet the
specifications in table 1.
5-5 Solderability
Subject the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the
terminals must be covered with new solder. It shall meet the specifications in table 1.
5-6 Mechanical shock
Drop the device randomly onto the concrete floor from the height of 1m 3 times. the device shall
fulfill the specifications in table 1.
5-7 Vibration
Subject the device to the vibration for 1 hour each in x,y and z axes with the amplitude of 1.5 mm at
10 to 55 Hz. The device shall fulfill the specifications in table 1.
5-8 Lead fatigue
5-8-1 Pulling test
Weight along with the direction of lead without an shock 1kg. The device shall satisfy all the initial
Characteristics.
5-8-2 Bending test
Lead shall be subject to withstand against 90℃ bending with 450g weight in the direction of
thickness. This operation shall be done toward both direction. The device shall show no evidence of
damage and shall satisfy all the initial electrical characteristics.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 5 of 6
SAW FILTER
HDBF07006A62
Typical frequency response
6. REMARK
6.1 Static voltage
Static voltage between signal load & ground may cause deterioration &destruction of the
component. Please avoid static voltage.
6.2 Ultrasonic cleaning
Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid
ultrasonic cleaning
6.3 Soldering
Only leads of component may be soldered. Please avoid soldering another part of component.
www.shoulder.cn
Tel:0755-82916880
Fax:0755-82916881
E-mail:[email protected]
Page 6 of 6