规格书编号 : SPEC NO : 产品规格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDBF11508A64 SF6-4 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2009-8-19 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDBF11508A64 SF6-4 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 6 SAW FILTER HDBF11508A64 SF6-4 1. ELECTRICAL SPECIFICATION Maximum Input Power DC voltage Storage Temperature Range Operation Temperature Range +10dBm 0V -45℃ to +85℃ -40℃ to +85℃ 2.1 Electronic Characteristics Parameter Center Frequency Insertion Loss -1.0dB Bandwidth -3dB Bandwidth -15dB Bandwidth -40dB Bandwidth Passband Variation Absolute delay Ultimate Rejection Material Temperature Coef Ambient Temperature Unit Min MHz dB MHz 8.2 MHz MHz MHz dB us dB 50 KHz/°C °C Type 115 33 8.25 8.5 9.0 9.3 1.0 4.5 55 2.6 25 Max 35 9.1 9.5 2.0 4.7 2.2 Typical Frequency Response www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 3 of 6 SAW FILTER HDBF11508A64 SF6-4 3. TEST CIRCUIT www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 6 SAW FILTER HDBF11508A64 SF6-4 4.DIMENSION 5. ENVIRONMENTAL CHARACTERISTICS 5-1 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in 2.1. 5-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in 2.1. 5-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 2.1. 5-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 6 SAW FILTER HDBF11508A64 SF6-4 filter shall fulfill the specifications in 2.1. 5-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2.1. 6. REMARK 6.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 6.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 6.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6