规格书编号 SPEC NO : 产品规格书 SPECIFICATION CUSTOMER 客 户： PRODUCT 产 品： SAW FILTER MODEL NO 型 号： HDF110N2 F11 PREPARED 编 制： CHECKED 审 核： APPROVED 批 准： D A T E 日 期： 2007-12-21 客户确认 CUSTOMER RECEIVED: 审核 CHECKED 批准 APPROVED 日期 DATE 无锡市好达电子有限公司 Shoulder Electronics Limited www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 1 of 6 SAW FILTER HDF110N2 F11 更改历史记录 History Record 更改日期 Date www.shoulder.cn 规格书编号 Spec. No. 产品型号 Part No. 客户产品型号 Customer No. Tel:0755-82916880 Fax:0755-82916881 更改内容描述 Modify Content E-mail:[email protected] 备注 Remark Page 2 of 6 SAW FILTER HDF110N2 F11 1. SCOPE This specification shall cover the characteristics of SAW filter with F110N2 used for the page system. 2. ELECTRICAL SPECIFICATION DC Voltage VDC AC Voltage Vpp Operation temperature Storage temperature RF Power Dissipation 10V 10V50Hz/60Hz -40℃ to +85℃ -45℃ to +85℃ 0dBm 2.2Electronic Characteristics 型号 Part Number 中心频率(fo)(MHz) Nominal Center Frequency 3dB 带宽 Bandwidth(from fo)(KHz) 阻带衰耗 Stop Band Attenuation (from peak level)(dB) 1)fo-5.0MHz 2)fo-3.5MHz 3)fo+/-2.0MHz 5)fo+3.5MHz 6)fo+5MHz 插入损耗(dB) Insertion Loss(at minimum loss point) 群延时波动(fo+/-576KHz)(μsce.) Group Delay Deviation 输入/输出阻抗 Input/output Impedance www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 HDF110N2 110.592 +/-350min 50min 45min 30min 40min 40min 4.5max 0.7 300Ω//1.2μH E-mail:[email protected] Page 3 of 6 SAW FILTER HDF110N2 F11 3.DIMENSION 4.TEST CIRCUIT www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 4 of 6 SAW FILTER HDF110N2 F11 5.Typical Frequency Response 6. ENVIRONMENTAL CHARACTERISTICS 6-1 Temperature cycling Subject the device to a low temperature of -40℃ for 30 minutes. Following by a high temperature of +25℃ for 5 Minutes and a higher temperature of +85℃ for 30 Minutes. Then release the device into the room conditions for 1 to 2 hours prior to the measurement. It shall meet the specifications in 2.2. 6-2 Resistance to solder heat Submerge the device terminals into the solder bath at 260℃ ±5℃ for 10±1 sec. Then release the device into the room conditions for 4 hours. It shall meet the specifications in 2.2. 6-3 Solderability Submerge the device terminals into the solder bath at 245℃ ±5℃ for 5s, More than 95% area of the soldering pad must be covered with new solder. It shall meet the specifications in 2.2. 6-4 Mechanical shock Drop the device randomly onto the concrete floor from the height of 1 m 3 times. the filter shall fulfill the specifications in 2.2. 6-5 Vibration Subject the device to the vibration for 2 hour each in x,y and z axes with the amplitude of 1.5 mm at 10 to 55 hz. The filter shall fulfill the specifications in 2.2. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 5 of 6 SAW FILTER HDF110N2 F11 7. REMARK 7.1 Static voltage Static voltage between signal load & ground may cause deterioration &destruction of the component. Please avoid static voltage. 7.2 Ultrasonic cleaning Ultrasonic vibration may cause deterioration & destruction of the component. Please avoid ultrasonic cleaning 7.3 Soldering Only leads of component may be soldered. Please avoid soldering another part of component. www.shoulder.cn Tel:0755-82916880 Fax:0755-82916881 E-mail:[email protected] Page 6 of 6