SC9642 CAR-CD DIGITAL SERVO SIGNAL PROCESSOR(SLAVE MODE) DESCRIPTION The SC9642 is a single-chip CD processor for digital servo and ASIC circuit. This LSI incorporates CD servo controller, CD signal processor, digital audio DAC and built-in CPU interface. FEATURES * Supports 1X to 2X speed playback * Command and sub code transmission adopts tri-line communication LQFP-64-10x10-0.5 or parallel communication. * Built-in MCU controls the CD and state feedback by communication instructions of the communication bus. * Supports format of CD-A/V, CD-R, CD-R/W and CD-ROM ORDERING INFORMATION APPLICATIONS * CD, VCD and MP3 player * Desk audio system Device Package SC9642 LQFP-64-10X10-0.5 BLOCK DIAGRAM HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 1 of 9 SC9642 ABSOLUTE MAXIMUM RATINGS (Tamb=25°C) Symbol Value Unit Supply Voltage Characteristic VDD -0.5 ~ +5.5 V Input Voltage On Pins VIN -0.5 ~ VDD + 0.5 V Tmax -40 ~ +85 °C Operating Temperature ELECTRICAL CHARACTERISTICS(VDD=3.4~5.5V;VSS=0V;Tamb=-10~+60°C) Characteristics Symbol Supply Voltage VDD Supply Current IDD Test Condition 5V; 1X Speed Min. Typ. Max. Unit 4.5 5.0 5.5 V － 45 － mA RFIN Input Signal VRFIN － 1.0 － V Reference Voltage VIr － 0.5VDD － V Common Mode DC VVCOM 2.0 2.5 － V Output ADC Reference Voltage VVCOM+ VVadc － 0.462 VVCOM+ 2.313 V Input Current Of Central Diode B IB 0 － 10 μA Input Current Of Central Diode A IA 0 － 10 μA Input Current Of Central Diode C IC 0 － 10 μA Input Current Of Central Diode D ID 0 － 10 μA Input Current Of Satellite Diode F IF 0 － 5 μA Input Current Of Satellite Diode F IE 0 － 5 μA IIdata 1.9 － 5.5 μA LDON Low Level Output Current ILDON 0 － 2 mA ERR Output Current IERR 0 1 － mA 0 1 － mA Data Slicer Feed-back Current Output DATA_OUT WCLK_OUT IOH1 SCLK_OUT IOL1 Output Current DATA_OUT WCLK_OUT SCLK_OUT VOL1 IOL1=1mA 0 － 0.4 V VOH1 IOH1=-1mA VDD-0.4 － VDD V Low Level Output Voltage DATA_OUT WCLK_OUT SCLK_OUT High Level Output Voltage RAD Output Current IRAD 0 1 － mA FOC Output Current IFOC 0 1 － mA SLED Output Current ISLED 0 1 － mA (To be continued) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 2 of 9 SC9642 (Continued) Characteristics MOTO Output Current RAD, FOC, SLED Low Level Output Voltage RAD, FOC, SLED High Level Output Voltage Symbol Test Condition IMOTO VOL IOL=1mA VOH IOH=-1mA Min. Typ. Max. Unit 0 10 － mA 0 － 0.4 V － VDD V VDD0.4 Moto Low Level Output Voltage VOLmoto IOLmoto=10mA 0 － 1.0 V Moto high Level Output Voltage VOHmoto IOHmoto=-10mA VDD-1 － VDD V IZO -10 0 +10 μA VILH 2.8 3.0 - V VIHL 0.6 － 0.7 V VOHda 0.7VDD － VDD+0.5 V VOLda -0.5 － 0.3VDD V 60 65 70 dB 0~19 kHz - - 0.001 dB 19~20 kHz - - 0.03 dB 24KHz 25 - - dB 25 ~ 35 KHz 40 - - dB 35 ~ 64 KHz 50 - - dB 64 ~68 KHz 31 - - dB 68KHz 35 - - dB 69~ 88KHz 40 - - dB RAD, FOC, SLED, MOTO Output 3-state Leakage Current ACK, WR, RD, DATA0～7, High Level Input Voltage ACK, WR, RD, DATA0～7, Low Level Input Voltage DATA_IN, WCLK_IN, SCLK_IN, High Level Input Voltage DATA_IN, WCLK_IN, SCLK_IN, Low Level Input Voltage DAC Total Harmonic Distortion Plus Noise DA Filter Attenuation (THD+N)/S Filter_DA Crystal Frequency Fsystem － 16.9344 － MHz SCLK Frequency FSCLK_IN － 2.8224 － MHz WCLK Frequency FWCLK_IN － 44.1 － KHz HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 3 of 9 SC9642 PIN CONFIGURATION PIN DESCRIPTION Pin No. Pin name Descriptions 1 VSSA1 Analog Ground 1 2 VDDA1 Analog Supply 1 3 B Central diode current signal input 4 A Central diode current signal input 5 C Central diode current signal input 6 D Central diode current signal input 7 F Satellite diode current signal input 8 E Satellite diode current signal input 9 VCOM 10 Vadc ADC reference voltage output 11 Idata Data signal feed-back current output DC voltage input (To be continued) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 4 of 9 SC9642 (Continued) Pin No. Pin name Descriptions 12 RFIN 13 RFREF 14 Ir 15 VSSA2 Analog ground 2 16 VDDA2 Analog supply 2 17 CRIN 18 CROUT 19 MODE EFM signal input Comparator common mode input Reference current output Crystal oscillation circuit input. When the master clock is input externally, input it from this pin. Crystal oscillation circuit output. Connect ground. Control the spindle motor (during focusing and jumping, if MOT_CTRL output high 20 MOT_CTRL level signal, it can control the MOT control port of SA9529 after through 3 voltage drop diodes, then prevent the spindle reverse; in other condition, the MOT-CTRL output low level). 21 WCLK_OUT D/A interface. LR clock output. 22 SCLK_OUT D/A interface. Bit clock output. 23 DATA_OUT D/A interface. Serial data output 24 ERR 25 WCLK_IN D/A interface. LR clock input. 26 SCLK_IN D/A interface. Bit clock input. 27 DATA_IN D/A interface. Serial data input 28 ACK 29 MCLK_IN 30 CL16 31 DATA \ WR 32 STB \ RD 33 ACK 34 IO.7 \ DATA7 General I/O port, it is shared with data bit 7 (drain open, with internal pull up resistor). 35 IO.6 \ DATA6 General I/O port, it is shared with data bit 6 (drain open, with internal pull up resistor). 36 IO.5 \ DATA5 General I/O port, it is shared with data bit 5 (drain open, with internal pull up resistor). 37 IO.4 \ DATA4 General I/O port, it is shared with data bit 4 (drain open, with internal pull up resistor). 38 IO.3 \ DATA3 General I/O port, it is shared with data bit 3 (drain open, with internal pull up resistor). 39 IO.2 \ DATA2 General I/O port, it is shared with data bit 2 (drain open, with internal pull up resistor). 40 IO.1 \ DATA1 General I/O port, it is shared with data bit 1 (drain open, with internal pull up resistor). 41 IO.0 \ DATA0 General I/O port, it is shared with data bit 0 (drain open, with internal pull up resistor). 42 TEST 43 RESET Reset pin (active low) 44 VDDA Analog Supply 45 VSSO Analog Ground 46 VDD0 Analog Supply C2 error flag Acknowledge Signal output pin (drain open, with pull up resistor). DAC system clock input (16.9344MHz) 16.9344MHZ clock output Data I/O port, it is shared with write port of parallel communication. Control I/O port, it is shared with read port of parallel communication.(drain open, with internal pull-up resistor). Acknowledge signal port (drain open, with internal pull-up resistor). Test pin. (To be continued) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 5 of 9 SC9642 (Continued) Pin No. Pin name 47 VREF Descriptions Internal reference voltage for output channels 48 R 49 CR Digital audio right channel output pin. Digital audio right channel filter pin. 50 CL Digital audio left channel filter pin. 51 L 52 RAD Tracking drive output 53 FOC Focus drive output 54 SLED Sled drive output 55 VSSP Ground 56 STATUS 57 BCLK 75Hz frame sync signal output pin. 58 MOTO Spindle drive output. 59 VDDP Digital power supply. Digital audio left channel output pin. Shake signal output (high active, used for anti-seismic system) 60 VDD Digital power supply. 61 GND Digital ground. 62 TRAY_SW Tray loading position monitor signal input 63 SLED_SW Sled motor position monitor signal input 64 LDON Laser control signal output (active high) HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 6 of 9 SC9642 TYPICAL APPLICATIONS CIRCUIT VCC Drive the sled, tray and spindle motor Control system GND GND GND MCU R 48 47 46 45 44 43 42 41 40 39 38 37 36 35 34 33 L 49 CR STB\RD 32 50 CL DATA\WR 31 51 L CL16 30 52 RAD MCLK_IN 29 53 FOC Driver ACK 28 54 SLED DATA_IN 27 55 VSSP SCLK_IN 26 SC9642 56 STATUS WCLK_IN 25 57 BCLK 58 MOTO VCC DATA_OUT 23 59 VDDP SCLK_OUT 22 60 VDD WCLK_OUT 21 GND 61 GND MUTE 20 Tray loading 62 TRAY_SW MODE 19 63 SLED_SW CROUT 18 Sled driver Audio, video processor ERR 24 64 LDON CRIN 17 AVCC AGND 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 RF processor Track, focus drive signal Mechanism HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn GND REV:1.1 GND 2008.03.24 Page 7 of 9 SC9642 PACKAGE OUTLINE LQFP-64-10x10-0.5 UNIT: mm HANDLING MOS DEVICES: Electrostatic charges can exist in many things. All of our MOS devices are internally protected against electrostatic discharge but they can be damaged if the following precautions are not taken: • Persons at a work bench should be earthed via a wrist strap. • Equipment cases should be earthed. • All tools used during assembly, including soldering tools and solder baths, must be earthed. • MOS devices should be packed for dispatch in antistatic/conductive containers. HANGZHOU SILAN MICROELECTRONICS CO.,LTD Http: www.silan.com.cn REV:1.1 2008.03.24 Page 8 of 9