Model PD1722J5050S3 Rev A Ultra Low Profile 0805 Power Divider 3 Way 50Ω to 50Ω Description The PD1722J5050S3 is a low profile, sub-miniature Wilkinson power divider in an easy to use surface mount package and is ideal for high volume manufacturing while delivering higher performances than traditional printed and lumped element solutions. It has been designed for the DCS, PCS, UMTS and CDMA markets. The PD1722J5050S3 is matched to 50 Ω and has a height profile of 0.84 mm. Three external resistors are required for operation. Components are available on tape and reel for high volume manufacturing pick and place. This components is constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal o coefficient of expansion (CTE) of 17 ppm/ C. Detailed Electrical Specifications: Specifications subject to change without notice. ROOM (25°C) Features: • • • • • • • • • • 1700 – 2200 MHz 0.84 mm Height Profile 50Ω Outputs/Inputs DCS/PCS/UMTS/CDMA External resistors required Low Insertion Loss Surface Mountable Tape & Reel Non-conductive Surface RoHS Compliant Parameter Frequency Input Port Impedance Output Port Impedance Return Loss Insertion Loss* Amplitude Balance Phase Balance Isolation (Output Ports) Power Handling Operating Temperature Min. 1700 Typ. Max 2200 50 50 11 0.9 0.5 9 17 9 14 1.3 0.9 12 1 +85 -55 Unit MHz Ω Ω dB dB dB Degrees dB Watts ºC * Insertion Loss stated at room temperature (Insertion Loss is approximately 0.1 dB higher at +85 ºC) Outline Drawing Top View (Near-side) Side View Bottom View (Far-side) .033±.002 [0.84±0.05] Orientation Marker Denotes Pin Location Dimensions are in Inches [Millimeters] Mechanical Outline Orientation Marker Denotes Pin Location Pin 1 2 3 4 5 6 Designation Output 1 GND Output 2 GND Input Output 3 1 2 3 6 5 4 Tolerances are Non-Cumulative Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD1722J5050S3 Rev A Typical Broadband Performance: 500 MHz. to 8.5 GHz. Return Loss - Input Insertion Loss 0 0 -6 -3 -9 -6 -12 -9 -15 -12 -15 -18 [dB] -21 -18 -21 -24 -24 -27 -27 -30 -30 -33 -33 5500 6000 6500 7000 7500 8000 8500 5500 6000 6500 7000 7500 8000 8500 5000 4500 4000 3500 3000 2500 2000 500 Frequency [MHz] 1500 -36 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 -36 1000 [dB] -3 Frequency [MHz] Phase Balance 1.500 15.0 1.000 10.0 0.500 5.0 Isolation -3 -6 -9 -12 -15 -18 -21 -24 -27 -30 -33 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 3000 2500 2000 1500 1000 500 -36 Frequency [MHz] (315) 432-8909 (800) 411-6596 +44 2392-232392 5000 4500 4000 3500 3000 2500 2000 Frequency [MHz] 0 USA/Canada: Toll Free: Europe: 1500 8500 8000 7500 7000 6500 6000 5500 5000 4500 4000 3500 -20.0 3000 -2.000 2500 -15.0 2000 -1.500 1500 -10.0 1000 -1.000 Frequency [MHz] [dB] 0.0 -5.0 1000 0.000 -0.500 500 deg 20.0 500 [dB] Amplitude Balance 2.000 Available on Tape and Reel for Pick and Place Manufacturing. Model PD1722J5050S3 Rev A Typical Performance: 1600 MHz. to 2300 MHz. Return Loss 0 Insertion Loss 0.0 -3 -0.3 -6 -0.6 -9 -0.9 -12 -1.2 -1.5 -18 [dB] -21 -1.8 Amplitude Balance 1.5 15.0 1.0 10.0 0.5 5.0 2300 2200 2300 2200 2100 2000 1600 -20.0 2300 -2.0 2200 -15.0 2100 -1.5 2000 -10.0 1900 -5.0 -1.0 1800 -0.5 1900 0.0 1800 0.0 1700 deg 20.0 1700 2100 Phase Balance 2.0 1600 2000 Frequency [MHz] Frequency [MHz] [dB] 1900 1800 2300 2200 2100 2000 -3.6 1900 -3.3 -36 1800 -3.0 -33 1700 -2.7 -30 1600 -2.4 -27 1700 -2.1 -24 1600 [dB] -15 Frequency [MHz] Frequency [MHz] Isolation 0.00 -3.00 -6.00 -9.00 -12.00 -18.00 -21.00 -24.00 -27.00 -30.00 -33.00 2300 2200 2100 2000 1900 1800 1700 -36.00 1600 [dB] -15.00 Frequency [MHz] Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD1722J5050S3 Rev A Mounting Configuration: In order for Xinger surface mount components to work optimally, the proper impedance transmission lines must be used to connect to the RF ports. If this condition is not satisfied, insertion loss, Isolation and VSWR may not meet published specifications. All of the Xinger components are constructed from ceramic filled PTFE composites which possess excellent electrical and mechanical stability having X and Y thermal coefficient of expansion (CTE) of 17 ppm/oC. An example of the PCB footprint used in the testing of these parts is shown below. In specific designs, the transmission line widths need to be adjusted to the unique dielectric coefficients and thicknesses as well as varying pick and place equipment tolerances. In addition, since the PD1722J5050S3 is a Wilkinson power divider, external 0402 100Ω resistors must be mounted as shown in the Figure below. Pad Footprint w/ 0402 Resistor Locations 4X Transmission Line R2 R1 R3 6X .002 [0.05] 6X .013 [0.33] Plated thru holes to ground 6X .016 [0.35] 4X .010 [0.25] Circuit Pattern Footprint Pad (s) Solder Resist USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing. .026 [0.66] Model PD1722J5050S3 Rev A Packaging and Ordering Information Parts are available in reels and are packaged per EIA 481-2. Parts are oriented in tape and reel as shown below. Minimum order quantities are 4000 per reel. See Model Numbers below for further ordering information. . ØA ØC ØD QUANTITY/REEL 4000 TABLE 1 REEL DIMENSIONS (inches [mm]) ØA 7.00 [177.8] B 0.32 [8.0] ØC 2.0 [50.8] ØD 0.512 [13.0] B Available on Tape and Reel for Pick and Place Manufacturing. USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Model PD1722J5050S3 Rev A USA/Canada: Toll Free: Europe: (315) 432-8909 (800) 411-6596 +44 2392-232392 Available on Tape and Reel for Pick and Place Manufacturing.