EDI MPIR40

FPIR32 MPIR40 KPIR50
MINIBRIDGE
FAST RECOVERY, 32, 40 and 50 AMPERES
INTEGRALLY MOLDED
HEAT SINKS
PROVIDE VERY LOW
THERMAL RESISTANCE
This mark indicates recognition under the component
program of Underwriters Laboratories, inc.
Our unique case construction enables the closer molding of integrated heat sink to the
active components for a superior thermal transfer and lower junction temperatures.
SERIES
50V
100V
200V
400V
600V
800V
1000V
FPIR SERIES
FPIR 3205 FPIR 3210
FPIR 3220
FPIR 3240
FPIR 3260
FPIR 3280
FPIR 32100
MPIR SERIES
MPIR 4005
MPIR 4010
MPIR 4020
MPIR 4040
MPIR 4060
MPIR 4080
MPIR 40100
KPIR SERIES KPIR 5005 KPIR 5010
KPIR 5020
KPIR 5040
KPIR 5060
KPIR 5080
KPIR 50100
ELECTRICAL CHARACTERISTICS PER LEG
(at TA =25 C U nle ss O the rwis e Sp ecif ied )
SERIES
FPIR 32
MPIR 40 KPIR 50
UNITS
Average Output Current, [email protected] Tc(Fig.1)
32
40
50
Amp
Max.Forward Voltage Drop,VF @ I F=12A (300 sec pulse)
1.4
1.4
1.4
Volts
Max.DC Reverse Current @ PRV and 25 C , IR
10
10
15
A
Max.DC Reverse Current @ PRV and 100 C ,IR
100
100
150
A
Max.Peak Surge Current, lFSM (8.3ms) (Fig.2)
240
320
900
Amp
Max. Reverse Recovery Time,Trr (Fig.3)
250
250
250
Nns.
Storage Temperature Range,TSTG
-55 to+150
Ambient Operating Temperature Range,TA
-55 to+150
Thermal Resistance (Total Bridge), R0- j-c
1.5 typ.
1.2 typ.
o
C
o
C
0.8 typ.
EDI reserves the rightto change these specifications at any time without notice.
o
C/W
FPIR32 MPIR40 KPIR50
FIG.2
NON-REPETITIVE SURGE CURRENT
FIG.1
CURRENT DERATING
1000
60
lO.AVERAGE
L
FORWARD CURRENT(AMP)
KPIR50
MAX.PEAK SURGE CURRENT IFSM
50
MPIR40
40
30
FPIR32
20
BRIDGE OUTPUT
RES.-IND. LOADS
10
500
KPIR50
MPIR40
200
100
FPIR32
50
20
Derate current by 20% for capacitive loads
0
10
0
25
O
50
O
75
O
O
100
125
O
150
O
1
5
2
10
20
50
100
NUMBER OF CYCLES AT 60 CPS
O
TC =TEMPERATURE( C)
FIG. 3
REVERSE RECOVERY TEST METHOD
T RR
R1
50 OHM
ZERO
D.U.T.
+
REFERENCE
0.5A
-
1.0A
0.25A
PULSE
GENERATOR
R2
1 OHM
SCOPE
R1, R2 NON-INDUCTIVE RESISTORS
PULSE GENERATOR - HEWLETT
PACKARD 214A OR EQUIV.
IKC REP.RATE, 10 SEC. PULSE WIDTH
ADJUST PULSE AMPLITUDE FOR PEAK IR
MPIR40 and FPIR32 MECHANICAL OUTLINE
Dielectric test voltage 2500 volts rms, max. 50-60Hz
.093 DIA. HOLE
1.125
.032
S
+
.250 FASTON
4 PLACES
EPOXY
CASE
.193 DIA
THRU HOLE
.6 MAX.
1.125
. 405 MAX
S
-
INTEGRATED
METAL HEAT SINK
1. Corrosion resistant terminals designed for .250 female quick connector, wrap around or solder.
2. A thin film of silicone thermal compound is recommended between the Minibridge R
case and mounting surface for improved thermal conduction.
3. Higher dielectric strengths available. Consult factory.
NOTE
Maximum lead and terminal temperature for soldering, 3/8 inch from case, 5 seconds at 250
C
ELECTRONIC DEVICES, INC. DESIGNERS AND MANUFACTURERS OF SOLID STATE DEVICES SINCE 1951.
21 GRAY OAKS AVENUE
* YONKERS. NEW YORK 10710 914-965-4400
Ee-mail:[email protected] *Wwebsite: http://www.edidiodes.com
* FAX 914-965-5531
* 1-800-678-0828