EUTECH EUP7201

EUP7201
Dual ,Low-Noise,150mA LDO Regulator
DESCRIPTION
FEATURES
The EUP7201 is highly accurate, Dual, low noise, CMOS
LDO voltage regulator. Performance features include low
output noise, high ripple rejection ratio, low dropout and
very fast turn-on times.
z
z
Up to 150mA Output Current (Each LDO)
Dual Shutdown Pins Control Each Output
z
124μVRMS Low Noise Output
The EUP7201 is also fully compatible with low ESR
ceramic capacitors, reducing cost and improving output
stability. This high level of output stability is maintained
even during frequent load fluctuations, due to the excellent
transient response performance and high PSRR achieved
across a broad range of frequencies.
z
z
z
z
z
z
Current Limiting and Thermal Protection
Short Circuit Protection
100mV Dropout at 100mA Load
Current Limiting Protection
Available in SOT23-6 ,TDFN-6 and USP-6 Package
RoHS Compliant and 100% Lead (Pb)-Free
The EN function allows the output of each regulator to be
turned off independently, resulting in greatly reduced
power consumption. The EUP7201 is available in the
SOT23-6 , TDFN-6 and USP-6 package.
APPLICATIONS
z
z
z
z
Typical Application Circuit
Figure 1.
DS7201 Ver 1.5 Oct. 2007
1
Cellular Phones
Camera, Video Recorders
PDAs
Hand-held Equipment
EUP7201
Pin Configurations
Package Type
Pin Configurations
Package Type
SOT23-6
Pin Configurations
TDFN-6
Package Type
Pin Configurations
USP-6
Pin Description
PIN
SOT23-6
TDFN-6
USP-6
DESCRIPTION
EN1
1
3
3
ON/OFF Control VOUT1
VIN
2
2
2
Supply Input
EN2
3
1
1
ON/OFF Control VOUT2
VOUT2
4
6
6
Channel 2 Output Voltage
GND
5
4
4
Ground
VOUT1
6
5
5
Channel1 Output Voltage
Note: If EN1 and EN2 are both low, both regulators and the reference turn off.
DS7201 Ver 1.5 Oct. 2007
2
EUP7201
Block Diagram
Figure 2.
Ordering Information
Order Number
Package Type
Marking
Operating Temperature range
EUP7201-1.5/2.8VIR1
SOT23-6
NC □ □ □ □
-40 °C to 85°C
EUP7201-1.8/2.8VIR1
SOT23-6
NA □ □ □ □
-40 °C to 85°C
EUP7201-1.8/2.6VIR1
SOT23-6
NU □ □ □ □
-40 °C to 85°C
EUP7201-1.8/3.3VIR1
SOT23-6
NH □ □ □ □
-40 °C to 85°C
EUP7201-2.5/2.8VIR1
SOT23-6
ND □ □ □ □
-40 °C to 85°C
EUP7201-2.8/1.2VIR1
SOT23-6
NP □ □ □ □
-40 °C to 85°C
EUP7201-2.8/2.8VIR1
SOT23-6
NM □ □ □ □
-40 °C to 85°C
EUP7201-2.8/3.0VIR1
SOT23-6
NK □ □ □ □
-40 °C to 85°C
EUP7201-2.8/3.3VIR1
SOT23-6
NL □ □ □ □
-40 °C to 85°C
EUP7201-3.0/3.0VIR1
SOT23-6
NN □ □ □ □
-40 °C to 85°C
EUP7201-3.0/3.3VIR1
SOT23-6
NT □ □ □ □
-40 °C to 85°C
EUP7201-3.3/3.3VIR1
SOT23-6
NJ □ □ □ □
-40 °C to 85°C
DS7201 Ver 1.5 Oct. 2007
3
EUP7201
Ordering Information (Continued)
Order Number
Package Type
EUP7201-1.8/2.8JIR1
TDFN-6
EUP7201-1.5/2.8UIR1
USP-6
EUP7201-1.8/2.8UIR1
USP-6
EUP7201-1.8/2.6UIR1
USP-6
EUP7201-1.8/3.3UIR1
USP-6
EUP7201-2.5/2.8UIR1
USP-6
EUP7201-2.8/1.2UIR1
USP-6
EUP7201-2.8/2.8UIR1
USP-6
EUP7201-2.8/3.0UIR1
USP-6
EUP7201-2.8/3.3UIR1
USP-6
EUP7201-3.0/3.0UIR1
USP-6
EUP7201-3.0/3.3UIR1
USP-6
EUP7201-3.3/3.3UIR1
USP-6
Marking
Operating Temperature range
xxxxx
7201A
xxx
NC
xxx
NA
xxx
NU
xxx
NH
xxx
ND
xxx
NP
xxx
NM
xxx
NK
xxx
NL
xxx
NN
xxx
NT
xxx
NJ
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
-40 °C to 85°C
EUP7201-□□/□□ □ □ □ □
Lead Free Code
1: Lead Free 0: Lead
Packing
R: Tape & Reel
Operating temperature range
I: Industry Standard
Package Type
V: SOT23 J: TDFN
U:USP
Output Voltage Option
* EUP7201-VOUT1/VOUT2 VIRI
DS7201 Ver 1.5 Oct. 2007
4
EUP7201
Absolute Maximum Ratings
▓
▓
▓
▓
▓
▓
Supply Input Voltage --------------------------------------------------------------------------------------- 6V
Power Dissipation, PD @ TA =25℃
SOT23-6 ------------------------------------------------------------------------------------------------------ 0.4W
Package Thermal Resistance
SOT23-6, θJA ------------------------------------------------------------------------------------------------- 250°C/W
Lead Temperature (Soldering,10 sec .) -------------------------------------------------------------------- 260°C
Storage Temperature Range -------------------------------------------------------------------------------- -65°C to 150°C
ESD Rating
HBM ---------------------------------------------------------------------------------------------------------- 2kV
Recommended Operating Conditions
▓
▓
▓
Supply Input Voltage ----------------------------------------------------------------------------------------- 2.5V to 5.5V
Enable Input Voltage ----------------------------------------------------------------------------------------- 0V to 5.5V
Junction Temperature Range ------------------------------------------------------------------------------- -40°C to 125°C
Electrical Characteristics
VIN= (VOUT+0.5V) or VIN=2.5V whichever is greater, CIN =COUT=1µF , EN1=EN2= VIN. TA=25°C.
Unless otherwise noted
Symbol
Parameter
Conditions
EUP7201
Min Typ Max.
IL=30mA
-2
2
IL=30mA, TA=-40°C~85°C.
-3
3
VOUT
Output voltage
IMAX
Maximum Output Current
Continuous ,TA=-40°C~85°C.
150
ILIM
Current Limit
Output Grounded (Steady State)
180
IG
VDROP
Quiescent Current
Dropout Voltage
ΔVOUT Load Regulation
Unit
%
mA
300
mA
No Load (Both LDOs)
110
180
µA
IOUT=150mA (Both LDOs)
260
µA
IOUT=30mA
30
mV
IOUT=100mA, TA=-40°C~85°C.
80
220
mV
13
60
mV
0.02
0.2
%/V
VIH
EN Input High Threshold
1mA< IOUT < 150mA
VIN=VOUT+0.5V to 5.5V
IOUT=1mA
VIN=2.5V to 5.5V, TA=-40°C~85°C.
VIL
EN Input Low Threshold
VIN=2.5V to 5.5V, TA=-40°C~85°C.
0.4
V
ISD
EN Input Bias Current
EN=GND or VIN
0.1
µA
IGSD
Shutdown Supply Current
EN1=EN2=GND
1
155
µA
℃
15
℃
60
dB
ΔVLINE Line Regulation
TSD
ΔTSD
PSRR
Thermal Shutdown Temperature
Thermal Shutdown Hysteresis
Ripple Rejection Rate
DS7201 Ver 1.5 Oct. 2007
VIN=(VOUT+1V) DC+0.5V p-p AC
IOUT=1mA, f=1kHz
5
1.6
V
0.01
EUP7201
Typical Operating Characteristics
DS7201 Ver 1.5 Oct. 2007
6
EUP7201
DS7201 Ver 1.5 Oct. 2007
7
EUP7201
DS7201 Ver 1.5 Oct. 2007
8
EUP7201
DS7201 Ver 1.5 Oct. 2007
9
EUP7201
Application Note
External Capacitors
Capacitor Characteristics
Like any low-dropout regulator, the EUP7201 requires
external capacitors for regulator stability. The EUP7201 is
specifically designed for portable applications requiring
minimum board space and smallest components. These
capacitors must be correctly selected for good
performance.
Input Capacitor
The EUP7201 is designed to work with ceramic
capacitors on the output to take advantage of the benefits
they offer: for capacitance values in the range of 1µF to
4.7µF range, ceramic capacitors are the smallest, least
expensive and have the lowest ESR values (which makes
them best for eliminating high frequency noise). The
ESR of a typical 1µF ceramic capacitor is in the range of
20mΩ to 40mΩ, which easily meets the ESR requirement
for stability by the EUP7201.
The ceramic capacitor’s capacitance can vary with
temperature. The capacitor type X7R, which operates
over a temperature range of -55°C to +125°C, will only
vary the capacitance to within ±15%. Most large value
ceramic capacitors ( ≈ 2.2µF) are manufactured with Z5U
or Y5V temperature characteristics. Their capacitance
can drop by more than 50% as the temperature goes from
25°C to 85°C. Therefore, X7R is recommended over Z5U
and Y5V in applications where the ambient temperature
will change significantly above or below 25°C.
On/Off Input Operation
An input capacitance of ≈ 1µF is required between the
EUP7201 input pin and ground (the amount of the
capacitance may be increased without limit).
This capacitor must be located a distance of not more than
1cm from the input pin and returned to a clean analog
ground. Any good quality ceramic, tantalum, or film
capacitor may be used at the input.
If a tantalum capacitor is used at the input, it must be
guaranteed by the manufacturer to have a surge current
rating sufficient for the application.
There are no requirements for the ESR on the input
capacitor, but tolerance and temperature coefficient must
be considered when selecting the capacitor to ensure the
capacitance will be ≈ 1µF over the entire operating
temperature range.
Output Capacitor
The EUP7201 is designed specifically to work with very
small ceramic output capacitors. A ceramic capacitor
(temperature characteristics X7R, X5R, Z5U, or Y5V) in 1
to 22µF range with 5mΩ to 500mΩ ESR range is suitable
in the EUP7201 application circuit.
The output capacitor must meet the requirement for
minimum amount of capacitance and also have an ESR
(Equivalent Series Resistance) value which is within a
stable range (5mΩ to 500mΩ)
No-Load Stability
The EUP7201 will remain stable and in regulation with no
external load. This is specially important in CMOS RAM
keep-alive applications.
DS7201 Ver 1.5 Oct. 2007
10
The EUP7201 is turned off by pulling the VEN pin low,
and turned on by pulling it high. If this feature is not used,
the VEN pin should be tied to VIN to keep the regulator
output on at all time. To assure proper operation, the
signal source used to drive the VEN input must be able
to swing above and below the specified turn-on/off
voltage thresholds listed in the Electrical Characteristics
section under VIL and VIH.
EUP7201
Packaging Information
SOT23-6
SYMBOLS
A
A1
b
D
MILLIMETERS
INCHES
MIN.
-
MAX.
1.45
MIN.
-
MAX.
0.057
0.00
0.30
0.15
0.50
0.000
0.012
0.006
0.020
2.90
0.114
1.60
0.95
0.063
0.037
E1
e
E
2.60
3.00
0.102
0.118
L
0.30
0.60
0.012
0.024
DS7201 Ver 1.5 Oct. 2007
11
EUP7201
TDFN-6
DETAIL A
SYMBOLS
A
A1
b
D
D1
E
E1
e
L
DS7201 Ver 1.5 Oct. 2007
MILLIMETERS
MIN.
MAX.
0.70
0.80
0.00
0.05
0.30
0.50
2.90
3.10
2.30
2.90
3.10
1.50
0.95
0.38
0.58
12
INCHES
MIN.
0.028
0.000
0.012
0.114
MAX.
0.031
0.002
0.020
0.122
0.090
0.114
0.122
0.059
0.037
0.015
0.023
EUP7201
USP-6
SYMBOLS
A
A1
b
b1
D
D1
E
E1
e
L
DS7201 Ver 1.5 Oct. 2007
MILLIMETERS
MIN.
MAX.
0.70
0.80
0.00
0.05
0.10
0.30
0.20
0.40
1.70
1.90
1.50
1.90
2.10
0.90
0.50
0.15
0.35
13
INCHES
MIN.
0.028
0.000
0.004
0.008
0.067
MAX.
0.031
0.002
0.012
0.016
0.075
0.059
0.075
0.083
0.035
0.020
0.006
0.014