HYNIX HY57V56820CLT-S

HY57V56820C(L)T
4 Banks x 8M x 8Bit Synchronous DRAM
DESCRIPTION
The HY57V56820C is a 268,435,456bit CMOS Synchronous DRAM, ideally suited for the main memory applications which require large
memory density and high bandwidth. The HY57V56820C is organized as 4banks of 8,388,608x8.
The HY57V56820C is offering fully synchronous operation referenced to a positive edge of the clock. All inputs and outputs are synchronized with the rising edge of the clock input. The data paths are internally pipelined to achieve very high bandwidth. All input and output
voltage levels are compatible with LVTTL.
Programmable options include the length of pipeline (Read latency of 2 or 3), the number of consecutive read or write cycles initiated by
a single control command (Burst length of 1,2,4,8 or full page), and the burst count sequence(sequential or interleave). A burst of read or
write cycles in progress can be terminated by a burst terminate command or can be interrupted and replaced by a new burst read or
write command on any cycle. (This pipelined design is not restricted by a `2N` rule.)
FEATURES
•
Single 3.3±0.3V power supply
•
Auto refresh and self refresh
•
All device pins are compatible with LVTTL interface
•
8192 refresh cycles / 64ms
•
JEDEC standard 400mil 54pin TSOP-II with 0.8mm of pin
pitch
•
Programmable Burst Length and Burst Type
•
All inputs and outputs referenced to positive edge of system
clock
- 1, 2, 4, 8 or Full page for Sequential Burst
•
Data mask function by DQM
•
Internal four banks operation
- 1, 2, 4 or 8 for Interleave Burst
•
Programmable CAS Latency ; 2, 3 Clocks
ORDERING INFORMATION
Part No.
Clock Frequency
HY57V56820CT-6
166MHz
HY57V56820CT-K
133MHz
HY57V56820CT-H
133MHz
HY57V56820CT-8
125MHz
HY57V56820CT-P
100MHz
HY57V56820CT-S
100MHz
HY57V56820CLT-6
166MHz
HY57V56820CLT-K
133MHz
Power
Organization
Interface
Package
4Banks x 8Mbits x8
LVTTL
400mil 54pin TSOP II
Normal
HY57V56820CLT-H
133MHz
HY57V56820CLT-8
125MHz
HY57V56820CLT-P
100MHz
HY57V56820CLT-S
100MHz
Low power
This document is a general product description and is subject to change without notice. Hyundai Electronics does not assume any responsibility for use of
circuits described. No patent licenses are implied.
Rev. 0.4 / July 2003
1
HY57V56820C(L)T
PIN CONFIGURATION
VDD
DQ0
VDDQ
NC
DQ1
VSSQ
NC
DQ2
VDDQ
NC
DQ3
VSSQ
NC
VDD
NC
/WE
/CAS
/RAS
/CS
BA0
BA1
A10/AP
A0
A1
A2
A3
VDD
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
54
53
52
51
50
49
48
47
46
45
44
43
54pin TSOP II 42
400mil x 875mil 41
0.8mm pin pitch 40
39
38
37
36
35
34
33
32
31
30
29
28
VSS
DQ7
VSSQ
NC
DQ6
VDDQ
NC
DQ5
VSSQ
NC
DQ4
VDDQ
NC
VSS
NC
DQM
CLK
CKE
A12
A11
A9
A8
A7
A6
A5
A4
VSS
PIN DESCRIPTION
PIN
PIN NAME
DESCRIPTION
CLK
Clock
The system clock input. All other inputs are registered to the SDRAM on the
rising edge of CLK
CKE
Clock Enable
Controls internal clock signal and when deactivated, the SDRAM will be one
of the states among power down, suspend or self refresh
CS
Chip Select
Enables or disables all inputs except CLK, CKE and DQM
BA0, BA1
Bank Address
Selects bank to be activated during RAS activity
Selects bank to be read/written during CAS activity
A0 ~ A12
Address
Row Address : RA0 ~ RA12, Column Address : CA0 ~ CA9
Auto-precharge flag : A10
RAS, CAS, WE
Row Address Strobe,
Column Address Strobe,
Write Enable
RAS, CAS and WE define the operation
Refer function truth table for details
DQM
Data Input/Output Mask
Controls output buffers in read mode and masks input data in write mode
DQ0 ~ DQ7
Data Input/Output
Multiplexed data input / output pin
VDD/VSS
Power Supply/Ground
Power supply for internal circuits and input buffers
VDDQ/VSSQ
Data Output Power/Ground
Power supply for output buffers
NC
No Connection
No connection
Rev. 0.4 / July 2003
2
HY57V56820C(L)T
FUNCTIONAL BLOCK DIAGRAM
8Mbit x 4banks x 8 I/O Synchronous DRAM
Self refresh logic
& timer
Internal Row
counter
8Mx8 Bank3
CLK
Row active
Column
Pre
Decoders
DQM
DQ0
I/O Buffer & Logic
Column
Active
Memory
Cell
Array
Sense AMP & I/O Gate
refresh
8Mx8 Bank0
X decoders
WE
8Mx8 Bank1
X decoders
CAS
8Mx8 Bank2
X decoders
RAS
State Machine
CS
Row
Pre
Decoders
X decoders
CKE
DQ1
DQ6
DQ7
Y decoders
Bank Select
A0
A1
Column Add
Counter
Address
Registers
Address buffers
A12
BA0
BA1
Rev. 0.4 / July 2003
Burst
Counter
Mode Registers
CAS Latency
Data Out Control
Pipe Line Control
3
HY57V56820C(L)T
ABSOLUTE MAXIMUM RATINGS
Parameter
Symbol
Rating
Unit
Ambient Temperature
TA
0 ~ 70
°C
Storage Temperature
TSTG
-55 ~ 125
°C
Voltage on Any Pin relative to VSS
VIN, VOUT
-1.0 ~ 4.6
V
Voltage on VDD relative to VSS
VDD, VDDQ
-1.0 ~ 4.6
V
Short Circuit Output Current
IOS
50
mA
Power Dissipation
PD
1
W
Soldering Temperature ⋅ Time
TSOLDER
260 ⋅ 10
°C ⋅ Sec
Note : Operation at above absolute maximum rating can adversely affect device reliability
DC OPERATING CONDITION (TA=0 to 70°C)
Parameter
Symbol
Min
Typ.
Max
Unit
Note
Power Supply Voltage
VDD, VDDQ
3.0
3.3
3.6
V
1
Input High Voltage
VIH
2.0
3.0
VDD + 0.3
V
1,2
Input Low Voltage
VIL
- 0.3
0
0.8
V
1,3
Note :
1.All voltages are referenced to VSS = 0V
2.VIH (max) is acceptable 5.6V AC pulse width with ≤3ns of duration
3.VIL (min) is acceptable -2.0V AC pulse width with ≤3ns of duration
AC OPERATING CONDITION (TA=0 to 70°C, VDD=3.3 ± 0.3V, VSS=0V)
Parameter
Symbol
Value
Unit
AC Input High / Low Level Voltage
VIH / VIL
2.4/0.4
V
Vtrip
1.4
V
Input Rise / Fall Time
tR / tF
1
ns
Output Timing Measurement Reference Level
Voutref
1.4
V
CL
50
pF
Input Timing Measurement Reference Level Voltage
Output Load Capacitance for Access Time Measurement
Note
1
Note :
1. Output load to measure access time is equivalent to two TTL gates and one capacitor (50pF)
For details, refer to AC/DC output circuit
Rev. 0.4 / July 2003
4
HY57V56820C(L)T
CAPACITANCE (TA=25°C, f=1MHz)
-6/K/H
Parameter
Pin
Input capacitance
Data input / output capacitance
-8/P/S
Symbol
Unit
Min
Max
Min
Max
CLK
CI1
2.5
3.5
2.5
4.0
pF
A0 ~ A12, BA0, BA1, CKE, CS, RAS, CAS,
WE, UDQM, LDQM
CI2
2.5
3.8
2.5
5.0
pF
DQ0 ~ DQ15
CI/O
4.0
6.5
4.0
6.5
pF
OUTPUT LOAD CIRCUIT
Vtt=1.4V
RT=250 Ω
Output
Output
50pF
50pF
DC Output Load Circuit
AC Output Load Circuit
DC CHARACTERISTICS I (TA=0 to 70°C, VDD=3.3±0.3V)
Parameter
Symbol
Min.
Max
Unit
Note
Input Leakage Current
ILI
-1
1
uA
1
Output Leakage Current
ILO
-1
1
uA
2
Output High Voltage
VOH
2.4
-
V
IOH = -4mA
Output Low Voltage
VOL
-
0.4
V
IOL = +4mA
Note :
1.VIN = 0 to 3.6V, All other pins are not tested under VIN =0V
2.DOUT is disabled, VOUT=0 to 3.6V
Rev. 0.4 / July 2003
5
HY57V56820C(L)T
DC CHARACTERISTICS II (TA=0 to 70°C, VDD=3.3±0.3V, VSS=0V)
Speed
Parameter
Operating Current
Precharge Standby Current
in Power Down Mode
Symbol
-6
-K
-H
-8
-P
-S
130
120
120
120
110
100
IDD1
Burst length=1, One bank active
tRC ≥ tRC(min), IOL=0mA
IDD2P
CKE ≤ VIL(max), tCK = 15ns
2.5
IDD2PS
CKE ≤ VIL(max), tCK = ∞
2.0
IDD2N
CKE ≥ VIH(min), CS ≥ VIH(min), tCK = 15ns
Input signals are changed one time during
30ns. All other pins ≥ VDD-0.2V or ≤ 0.2V
35
IDD2NS
CKE ≥ VIH(min), tCK = ∞
Input signals are stable.
20
IDD3P
CKE ≤ VIL(max), tCK = 15ns
5.0
IDD3PS
CKE ≤ VIL(max), tCK = ∞
5.0
IDD3N
CKE ≥ VIH(min), CS ≥ VIH(min), tCK = 15ns
Input signals are changed one time during
30ns. All other pins ≥ VDD-0.2V or ≤ 0.2V
45.0
IDD3NS
CKE ≥ VIH(min), tCK = ∞
Input signals are stable.
30.0
Precharge Standby Current
in Non Power Down Mode
Active Standby Current
in Power Down Mode
Test Condition
Active Standby Current
in Non Power Down Mode
Burst Mode Operating Current IDD4
tCK ≥ tCK(min), IOL=0mA
All banks active
Auto Refresh Current
IDD5
tRRC ≥ tRRC(min), All banks active
Self Refresh Current
IDD6
CKE ≤ 0.2V
Unit
Note
mA
1
mA
mA
mA
CL=3
mA
150
130
130
130
120
110
mA
1
220
220
220
200
200
200
mA
2
3
mA
3
1.5
mA
4
Note :
1.IDD1 and IDD4 depend on output loading and cycle rates. Specified values are measured with the output open
2.Min. of tRRC (Refresh RAS cycle time) is shown at AC CHARACTERISTICS II
3.HY57V56820CT-6/K/H/8/P/S
4.HY57V56820CLT-6/K/H/8/P/S
Rev. 0.4 / July 2003
6
HY57V56820C(L)T
AC CHARACTERISTICS I (AC operating conditions unless otherwise noted)
-6
Parameter
CAS Latency = 3
tCK3
Max
6
Min
Max
7.5
1000
-8
-P
-S
Min
Max
7.5
1000
Max
8
1000
10
Min
Max
10
1000
10
Min
10
1000
10
Note
Max
ns
1000
7.5
Clock High Pulse Width
tCHW
2.5
-
2.5
-
2.5
-
3
-
3
-
3
-
ns
1
Clock Low Pulse Width
tCLW
2.5
-
2.5
-
2.5
-
3
-
3
-
3
-
ns
1
CAS Latency = 3
tAC3
-
5.4
-
5.4
-
5.4
-
6
-
6
-
6
ns
CAS Latency = 2
tAC2
-
6
-
5.4
-
6
-
6
-
6
-
6
ns
Data-Out Hold Time
tOH
2.7
-
2.7
-
2.7
-
3
-
3
-
3
-
ns
Data-Input Setup Time
tDS
1.5
-
1.5
-
1.5
-
2
-
2
-
2
-
ns
1
Data-Input Hold Time
tDH
0.8
-
0.8
-
0.8
-
1
-
1
-
1
-
ns
1
Address Setup Time
tAS
1.5
-
1.5
-
1.5
-
2
-
2
-
2
-
ns
1
Address Hold Time
tAH
0.8
-
0.8
-
0.8
-
1
-
1
-
1
-
ns
1
CKE Setup Time
tCKS
1.5
-
1.5
-
1.5
-
2
-
2
-
2
-
ns
1
CKE Hold Time
tCKH
0.8
-
0.8
-
0.8
-
1
-
1
-
1
-
ns
1
Command Setup Time
tCS
1.5
-
1.5
-
1.5
-
2
-
2
-
2
-
ns
1
Command Hold Time
tCH
0.8
-
0.8
-
0.8
-
1
-
1
-
1
-
ns
1
CLK to Data Output in Low-Z Time
tOLZ
1
-
1
-
1
-
1
-
1
-
1
-
ns
CLK to Data Output
in High-Z Time
7.5
Min
tCK2
Access Time From
Clock
CAS Latency = 2
-H
Unit
Min
System Clock Cycle
Time
-K
Symbol
12
ns
2
CAS Latency = 3
tOHZ3
2.7
5.4
2.7
5.4
2.7
5.4
3
6
3
6
3
6
ns
CAS Latency = 2
tOHZ2
2.7
5.4
2.7
5.4
3
6
3
6
3
6
3
6
ns
Note :
1.Assume tR / tF (input rise and fall time ) is 1ns
2.Access times to be measured with input signals of 1v/ns edge rate
Rev. 0.4 / July 2003
7
HY57V56820C(L)T
AC CHARACTERISTICS II
-6
Parameter
-K
-H
-8
-P
-S
Symbol
Unit
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Min
Max
Operation
tRC
60
-
60
-
65
-
68
-
70
-
70
-
ns
Auto Refresh
tRRC
60
-
60
-
65
-
68
-
70
-
70
-
ns
RAS to CAS Delay
tRCD
18
-
15
-
20
-
20
-
20
-
20
-
ns
RAS Active Time
tRAS
42
100K
45
100K
45
100K
48
100K
50
100K
50
100K
ns
RAS Precharge Time
tRP
18
-
15
-
20
-
20
-
20
-
20
-
ns
RAS to RAS Bank Active Delay
tRRD
12
-
15
-
15
-
16
-
20
-
20
-
ns
CAS to CAS Delay
tCCD
1
-
1
-
1
-
1
-
1
-
1
-
CLK
Write Command to Data-In Delay
tWTL
0
-
0
-
0
-
0
-
0
-
0
-
CLK
Write Recovery Time
tWR
2
-
2
-
2
-
2
-
2
-
2
-
CLK
Data-In to Active Command
tDAL
5
-
5
-
5
-
5
-
5
-
5
-
CLK
DQM to Data-Out Hi-Z
tDQZ
2
-
2
-
2
-
2
-
2
-
2
-
CLK
DQM to Data-In Mask
tDQM
0
-
0
-
0
-
0
-
0
-
0
-
CLK
MRS to New Command
tMRD
2
-
2
-
2
-
2
-
2
-
2
-
CLK
CAS Latency = 3
tPROZ3
3
-
3
-
3
-
3
-
3
-
3
-
CLK
CAS Latency = 2
tPROZ2
2
-
2
-
2
-
2
-
2
-
2
-
CLK
Power Down Exit Time
tPDE
1
-
1
-
1
-
1
-
1
-
1
-
CLK
Self Refresh Exit Time
tSRE
1
-
1
-
1
-
1
-
1
-
1
-
CLK
Refresh Time
tREF
-
64
-
64
-
64
-
64
-
64
-
64
ms
Note
RAS Cycle Time
Precharge to Data
Output Hi-Z
1
Note :
1. A new command can be given tRRC after self refresh exit
Rev. 0.4 / July 2003
8
HY57V56820C(L)T
IBIS SPECIFICATION
IOH Characteristics (Pull-up)
Voltage
100MHz
(Min)
100MHz
(Max)
66MHz
(Min)
(V)
I(mA)
I(mA)
I(mA)
-2.4
3.3
-27.3
0
0.5
1
1.5
2
2.5
3
3.5
0
-100
3.0
0
-74.1
-0.7
2.6
-21.1
-129.2
-7.5
2.4
-34.1
-153.3
-13.3
2.0
-58.7
-197
-27.5
1.8
-67.3
-226.2
-35.5
1.65
-73
-248
-41.1
1.5
-77.9
-269.7
-47.9
1.4
-80.8
-284.3
-52.4
1.0
-88.6
-344.5
-72.5
0
-93
-502.4
-93
-200
I (mA)
3.45
66MHz and 100MHz Pull-up
-300
-400
-500
-600
Voltage (V)
IOH Min (100MHz)
IOH Min (66MHz)
IOH Max (66 /100MHz)
IOL Characteristics (Pull-down)
66MHz and 100MHz Pull-down
Voltage
100MHz
(Min)
100MHz
(Max)
66MHz
(Min)
(V)
I(mA)
I(mA)
I(mA)
0
0
0
0
0.4
27.5
70.2
17.7
0.65
41.8
107.5
26.9
0.85
51.6
133.8
33.3
1.0
58.0
151.2
37.6
1.4
70.7
187.7
46.6
1.5
72.9
194.4
48.0
1.65
75.4
202.5
49.5
1.8
77.0
208.6
50.7
Voltage (V)
1.95
77.6
212.0
51.5
IOL Min (100MHz)
3.0
80.3
219.6
54.2
IOL Min (66MHz)
3.45
81.4
222.6
54.9
IOL Max (100MHz)
Rev. 0.4 / July 2003
250
I (mA)
200
150
100
50
0
0
0.5
1
1.5
2
2.5
3
3.5
9
HY57V56820C(L)T
DEVICE OPERATING OPTION TABLE
HY57V56820C(L)T-6
166MHz(6ns)
143MHz(7ns)
133MHz(7.5ns)
CAS Latency
tRCD
tRAS
tRC
tRP
tAC
tOH
3CLKs
3CLKs
2CLKs
3CLKs
3CLKs
3CLKs
7CLKs
6CLKs
6CLKs
10CLKs
9CLKs
9CLKs
3CLKs
3CLKs
3CLKs
5.4ns
5.4ns
5.4ns
2.7ns
2.7ns
2.7ns
HY57V56820C(L)T-K
133MHz(7.5ns)
125MHz(8ns)
100MHz(10ns)
CAS Latency
tRCD
tRAS
tRC
tRP
tAC
tOH
3CLKs
3CLKs
2CLKs
3CLKs
3CLKs
2CLKs
7CLKs
6CLKs
6CLKs
10CLKs
9CLKs
9CLKs
3CLKs
3CLKs
3CLKs
5.4ns
6ns
6ns
2.7ns
3ns
3ns
CAS Latency
tRCD
tRAS
tRC
tRP
tAC
tOH
2CLKs
3CLKs
2CLKs
2CLKs
3CLKs
2CLKs
6CLKs
6CLKs
5CLKs
8CLKs
9CLKs
7CLKs
2CLKs
3CLKs
2CLKs
5.4ns
6ns
6ns
2.7ns
3ns
3ns
CAS Latency
tRCD
tRAS
tRC
tRP
tAC
tOH
3CLKs
2CLKs
2CLKs
3CLKs
2CLKs
2CLKs
6CLKs
5CLKs
4CLKs
9CLKs
7CLKs
6CLKs
3CLKs
2CLKs
2CLKs
6ns
6ns
6ns
3ns
3ns
3ns
HY57V56820C(L)T-H
133MHz(7.5ns)
125MHz(8ns)
100MHz(10ns)
HY57V56820C(L)T-8
125MHz(8ns)
100MHz(10ns)
83MHz(12ns)
HY57V56820C(L)T-P
100MHz(10ns)
83MHz(12ns)
66MHz(15ns)
CAS Latency
tRCD
tRAS
tRC
tRP
tAC
tOH
2CLKs
2CLKs
2CLKs
2CLKs
2CLKs
2CLKs
5CLKs
5CLKs
4CLKs
7CLKs
7CLKs
6CLKs
2CLKs
2CLKs
2CLKs
6ns
6ns
6ns
3ns
3ns
3ns
HY57V56820C(L)T-S
100MHz(10ns)
83MHz(12ns)
66MHz(15ns)
Rev. 0.4 / July 2003
CAS Latency
tRCD
tRAS
tRC
tRP
tAC
tOH
3CLKs
2CLKs
2CLKs
2CLKs
2CLKs
2CLKs
5CLKs
5CLKs
4CLKs
7CLKs
7CLKs
6CLKs
2CLKs
2CLKs
2CLKs
6ns
6ns
6ns
3ns
3ns
3ns
10
HY57V56820C(L)T
COMMAND TRUTH TABLE
Command
A10/
AP
CKEn-1
CKEn
CS
RAS
CAS
WE
DQM
Mode Register Set
H
X
L
L
L
L
X
OP code
H
X
X
X
No Operation
H
X
X
X
L
H
H
H
Bank Active
H
X
L
L
H
H
X
H
X
L
H
L
H
X
ADDR
RA
Read
Note
V
L
CA
Read with Autoprecharge
V
H
Write
L
H
X
L
H
L
L
X
CA
Write with Autoprecharge
H
X
L
L
H
L
X
Burst Stop
H
X
DQM
H
Auto Refresh
H
H
L
L
L
Burst-Read-Single-WRITE
H
X
L
L
Entry
H
L
L
H
H
H
Exit
L
H
L
L
V
X
V
X
H
X
X
L
H
X
A9 Pin High
(Other Pins OP code)
L
L
H
X
X
X
X
X
X
L
H
H
H
H
X
X
X
L
H
H
H
H
X
X
X
L
H
H
H
H
X
X
X
L
V
V
V
L
Precharge
power down
X
X
X
Self Refresh1
H
L
H
X
Precharge selected Bank
Entry
V
H
Precharge All Banks
X
X
Exit
Clock
Suspend
BA
Entry
Exit
L
H
L
H
X
L
H
X
X
X
X
Note :
1. Exiting Self Refresh occurs by asynchronously bringing CKE from low to high
2. X = Don′t care, H = Logic High, L = Logic Low. BA =Bank Address, RA = Row Address, CA = Column Address,
Opcode = Operand Code, NOP = No Operation
Rev. 0.4 / July 2003
11
HY57V56820C(L)T
PACKAGE INFORMATION
400mil 54pin Thin Small Outline Package
UNIT : mm(inch)
11.938(0.4700)
11.735(0.4620)
22.327(0.8790)
22.149(0.8720)
10.262(0.4040)
10.058(0.3960)
0.150(0.0059)
0.050(0.0020)
0.80(0.0315)BSC
Rev. 0.4 / July 2003
0.400(0.016)
0.300(0.012)
1.194(0.0470)
0.991(0.0390)
5deg
0deg
0.597(0.0235)
0.406(0.0160)
0.210(0.0083)
0.120(0.0047)
12