AZDISPLAYS ATM2412B-FLW-XFW

AZ DISPLAYS
SPECIFICATIONS FOR
LIQUID CRYSTAL DISPLAY
CUSTOMER APPROVAL
※ PART NO. : ATM2412B SERIES (AZ DISPLAYS) VER 1.1
APPROVAL
COMPANY
CHOP
CUSTOMER
COMMENTS
AZ DISPLAYS ENGINEERING APPROVAL
DESIGNED BY
GU
CHECKED BY
APPROVED BY
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
REVISION RECORD
REVISION
REVISION DATE
VER1.0
2012-08-29
VER1.1
2013-04-17
AZ DISPLAYS
PAGE
CONTENTS
FIRST ISSUE
5
REVISE VIEWING ANGLE
1
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
※ CONTENTS
1.0 GENERAL SPECS
2.0 ABSOLUTE MAXIMUM RATINGS
3.0 ELECTRICAL CHARACTERISTICS
4.0 OPTICAL CHARACTERISTICS
5.0 BLOCK DIAGRAM
6.0 PIN ASSIGNMENT
7.0 POWER SUPPLY
8.0 TIMING CHARACTERISTICS
9.0 MECHANICAL DIAGRAM
10.0 RELIABILITY TEST
11.0 DISPLAY INSTRUCTION TABLE
12.0 PRECAUTION FOR USING LCM
Appendix: P/N description
AZ DISPLAYS
2
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
1.0 GENERAL SPECS
ATM2412B series TFT graphic module is an advanced product which adopts TFT and FPGA technology.
It can perfectly replace the old 240*128 STN/FSTN graphic module with almost no change on hardware and
software. Customer can easily get higher contrast, wider viewing angle, better high/low temperature
performance and other features with least cost increasing.
1. Display Format
240*128 DOTS
2. Power Supply LCM
5.0V/3.3V (Refer to P/N description in last page)
3. Overall Module Size
144.0mm(W) x 104.0mm(H) x max 10.0mm(D) *
4.
Viewing Area(W*H)
113.5mm(W) x 64.0mm(H)
5.
Pixel Pitch (W*H)
0.462mm(W) x 0.462mm(H)
6.
Active Area(W*H)
110.88mm(W) x 59.136mm(H)
6.
Viewing Direction
Free viewing angle
7.
Driving Method
TFT
8.
Controller IC
RA6963 or compatible
9.
Display Mode
Customized display mode(Refer to P/N description)
10. Backlight Options
White LED/Side
11. Operating temperature
-20ºC ~ 70ºC
12. Storage temperature
-30ºC ~ 80ºC
13. RoHS
RoHS compliant
* Doesn't contain connector height
2.0 ABSOLUTE MAXIMUM RATINGS
Item
Symbol
Min
Typ
Max
Unit
Operating temperature
Top
-20
--
70
ºC
Storage temperature
Tst
-30
--
80
ºC
Input voltage
Vin
Vss-0.3
--
Vdd+0.3
V
Vdd- Vss
-0.3
-
7.0
V
Supply voltage for logic
3.0 ELECTRICAL CHARACTERISTICS
3.1 Electrical Characteristics Of LCM
Item
Symbol
Condition
Power Supply Voltage
Vdd
25ºC
Power Supply Current
Idd
Input voltage (high)
Vih
Input voltage (low)
Vil
AZ DISPLAYS
Min
Typ
Max
Unit
4.8
5.0
5.2
3.0
3.3
3.6
Vdd=5.0V
--
--
65
Vdd=3.3V
--
--
55
Pins:( /WR, /RD, /CE, C/D,
/RESET,DB0-DB7,FS)
0.8Vdd
--
Vdd
V
0
--
0.2Vdd
V
V
mA
3
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
3.2 The Characteristics Of LED Backlight
3.2.1 Electrical-Optical Characteristics Of LED Backlight (Ta=25ºC)
Item
Symbol
Condition
Min
Typ
Max
Unit
Forward Voltage
Vf
--
3
5
5.5
V
Forward Current(5)
If
Vf = 5V
--
206
--
mA
Luminance
Lv
Vf = 5V
200
250
--
cd/㎡
Uniformity(2)
Δ
(Lvmin/Lvmax)%
70%
75%
--
-
0.26
--
0.36
-
0.28
--
0.38
-
-
20000
-
Hours
(1)(5)
(3)
Chroma coordinate
x
Vf = 5V
y
Lifetime(4)
-
Vf = 5V
NOTE:
(1) Forward voltage means voltage applied to Pin21 & Pin22
(2)The luminance is the average value of 5 points,The measurement instrument is BM-7 luminance
colorimeter.The diameter of aperture is Φ5mm
(3) Luminance when LCM displaying white color.
(4) Backlight lifetime means luminance value larger than half of the original after 20000 hours’ continuous
working.
(5) Input current of Pin 21 might change because the voltage of PIN21 will affect the efficiency of backlight
driving circuit, but current for LEDs will keep constant within the range of input voltage.
3.2.2 Backlight Control Circuit For LCM(2x6=12 pcs LED)
2 2 :0 V
2 1 :+ 3 V ~ 5 .5 V IN
B L D R IV IN G
C IR C U IT
P IN 2 2 is c o n n e c te d to P IN 2 (V S S ) in te rn a lly
3.2.3 LED Characteristics Curves(for single led)
2.Forward
1.Forward current VS.Ambient Temperature
Forward Current (mA)
25
)
A
m
(
t
n
e
r
r
u
C
d
r
a
w
r
o
F
20
15
10
5
0
-30
current VS Forward Voltage
30
25
20
15
10
5
0
0
25
50 80
Ambient Temperature
AZ DISPLAYS
100
4
2
3
Forward Voltage
5
4
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
4.0 OPTICAL CHARACTERISTICS (Ta=25ºC)
Item
Symbol
Condition
Min
Typ
Max
Unit
Viewing angle (Left - right)
θ2
Cr ≥ 2.0
-80
-
80
deg
Viewing angle (Up-down)
θ1
Cr ≥ 2.0
-80
-
80
deg
FT:white,BG:black
400
500
-
FT:black,BG:white
400
500
-
FT:white,BG:blue
48
60
-
FT:black,BG:Y-G
320
400
-
-
Contrast Ratio
(θ1=0°, θ2=0°)
Cr
Response time (rise)
Tr
θ1=0°, θ2=0°
-
10
20
ms
Response time (fall)
Tf
θ1=0°, θ2=0°
-
15
30
ms
(1). Definition of Optical Response Time
(2). Definition of Contrast Ratio
AZ DISPLAYS
5
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
(3). Definition of Viewing Angle θ2 and θ1
5.0 BLOCK DIAGRAM
AZ DISPLAYS
6
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
6.0 PIN ASSIGNMENT
Pin No.
Symbol
Function
I/O
1
FGND
Frame Ground, connected to VSS
via a 1M ohms resistor internally
P
2
VSS
Power ground
P
3
VDD
5V/3.3V
P, Refer to P/N description
4
D.C.
Don't care
-
5
/WR
Data write
I
6
/RD
Data read
I
7
/CE
Chip Enable
I
8
C/D
Command/Data
I
9
NC
No connection
-
10
/RESET
Reset
I
11
Data bit 0
I/O
12
DB0
DB1
Data bit 1
I/O
13
DB2
Data bit 2
I/O
14
DB3
Data bit 3
I/O
15
DB4
Data bit 4
I/O
16
DB5
Data bit 5
I/O
17
DB6
Data bit 6
I/O
18
DB7
Data bit 7
I/O
19
FS
Font SelectH=6*8dots matrix,
L=8*8 dot matrix
I
20
22
BL-
Don't care
Power supply for LED driving
circuit, 5V typical
Power ground for LED driving
circuit, internally connected to VSS
-
21
D.C.
BL+
AZ DISPLAYS
P
P
7
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
7.0 POWER SUPPLY
8.0 TIMING CHARACTERISTICS
For more details, please refer to IC specification.
AZ DISPLAYS
8
AZ DISPLAYS
1
12.5
16.9
3.5
A
22
110.880(A.A.)
2
3
4
5
5
P2.54*(22-1)=53.34 ± 0.2
DISPLAY CENTER
138.0
113.5(BEZEL OPEN)
121.9(BEZEL OUTLINE)
144.0± 0.5(OUTLINE)
4
Unspecified tolerance: ± 0.2mm
11.0
3
1
15.0
3
2
1
REV
ECN NO.
6
2.5
6
4.1± 0.3
1.6± 0.1
10.0MAX
7
Dot size
0.462
8
A
SH NO 1/1
REV
CN/DATE
2012-08-22
8
First issued
7
NATURE OF MODIFICATION
0.462
B
16.6
15.2
3.0
19.3
C
D
E
F
2
.0
4-? 3
1
A
B
C
D
E
F
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
9.0 MECHANICAL DIAGRAM
59.136(A.A.)
77.0(BEZEL OUTLINE)
64.0(BEZEL OPEN)
97.0
104.0± 0.5(OUTLINE)
9
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
10.0 RELIABILITY TEST
Test Item
NO
1
High temperature
storage
2
Low temperature
storage
3
High temperature
Operation
4
Environmental
Test
5
6
Low temperature
Operation
High
temperature/High
Humidity Storage
Temperature Cycle
Description
Applying the high storage
temperature Under normal humidity for a
long time Check normal performance
Applying the low storage temperature
Under normal humidity for a long time
Check normal performance
Apply the electric stress(Voltage and
current) Under high temperature for a
long time
Apply the electric stress Under low
temperature for a long time
Apply high temperature and high
humidity storage for a long time
Apply the low and high temperature cycle
-30ºC<>25ºC<>80ºC <>25ºC
30min
10min 30min 10min
Test Condition
Remark
80 ºC
96hrs
-30ºC
96hrs
70 ºC
96hrs
Note1
-20ºC
96hrs
Note1
Note2
90% RH
40ºC
96hrs
Note2
-30ºC/80ºC
10 cycle
1 cycle
Check normal performance
Vibration
test(Package state)
7
Applying vibration to product check
normal performance
Mechanical
Test
Shock test(package
state)
8
9
Applying shock to product check normal
performance
Freq:10~55~10Hz
Amplitude:0.75mm
1cycle time:1min
X.Y.Z every
direction for 15
cycles
Drop them through
70cm height to
strike horizontal
plane
Other
Remark
Note1:Normal operations condition (25ºC±5ºC).
Note2:Pay attention to keep dewdrops from the module during this test.
AZ DISPLAYS
10
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
11.0 DISPLAY INSTRUCTION TABLE
INSTRUCTION
C/
D
R
D
W
R
D
7
D
6
D
5
D
4
D
3
D
2
D
1
D
0
DESCRIPTION
S4
Status Read
1
0
1
S7
S6
S5
Register Set
1
1
0
0
0
1
Control Word Set
Mode Set
1
1
1
1
0
0
0
1
1
0
0
0
N
ot
us
ed
0
S3
S2
S1
S0
S1~S5
0: In operation
1: Ready
S6
0:No Error
1:Error
S7
0:Display Off
1:Normal Display
0
0
0
1
0
1
0
1
0
0
Set Cursor Pointer
Set Offset Register
Set Address Pointer
0
1
0
1
Set Text Home Address
Set Text Area
Set Graphic Home Address
Set graphic Area
0
0
0
0
0
1
1
0
X
X
X
X
0
1
0
0
0
1
X
X
0
0
1
0
X
X
0
1
1
0
X
X
OR mode
EXOR mode
AND mode
Text Attribute mode
Internal CG ROM mode
External CG RAM mode
0
X
X
1
0
1
N
2
0
1
1
X
X
X
N
1
0
0
1
0
0
1
X
X
X
N
0
0
1
0
Display Off
Cursor on,blink off
Cursor on,blink on
Text on,graphic off
Text off,graphic on
Text on,graphic on
Display Mode
1
1
0
1
0
0
1
0
X
X
0
1
1
Cursor Pattern Select
1
1
0
1
1
0
0
0
Data Auto Read /Write
1
1
0
1
0
1
1
0
0
Cursor Set
Set Data Auto Write
Set Data Auto Read
Auto Reset
Data Read Write
1
1
0
1
1
0
0
0
N
2
N
1
N
0
Data Read/Write And
ADP Increment/Decrement
It should executed after setting
Address using Set Address
Pointer command.
Screen Peek
1
1
0
1
1
1
0
0
0
0
0
Screen Peek
Screen Copy
1
1
0
1
1
1
0
1
0
0
0
Screen Copy
Bit Set Reset
1
1
0
1
1
1
1
N
3
N
2
1
N
0
Bit Set
Data Write
0
1
0
Write Data
Data Read
0
0
1
Read Data
Writes data DBO~DB7 from
MPU to external display RAM.
Reads data DB0~DB7 from
external display RAM to MPU.
x : invalid
For more information please refer to controller Specification.
AZ DISPLAYS
11
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
12.0 PRECAUTION FOR USING LCM
1. When design the product with this LCD Module, make sure the viewing angle matches to its purpose of usage.
2. As LCD panel is made of glass substrate, Dropping the LCD module or banging it against hard objects may
cause cracking or fragmentation. Especially at corners and edges.
3. Although the polarizer of this LCD Module has the anti-glare coating, always be careful not to scratch its
surface. Use of a plastic cover is recommended to protect the surface of polarizer.
4. If the LCD module is stored at below specified temperature, the LC material may freeze and be deteriorated. If
it is stored at above specified temperature, the molecular orientation of the LC material may change to Liquid
state and it may not revert to its original state. Excessive temperature and humidity could cause polarizer peel
off or bubble. Therefore, the LCD module should always be stored within specified temperature range.
5. Saliva or water droplets must be wiped off immediately as those may leave stains or cause color changes if
remained for a long time. Water vapor will cause corrosion of ITO electrodes.
6. If the surface of LCD panel needs to be cleaned, wipe it swiftly with cotton or other soft cloth. If it is not still
clean enough, blow a breath on the surface and wipe again.
7. The module should be driven according to the specified ratings to avoid malfunction and permanent damage.
Applying DC voltage cause a rapid deterioration of LC material. Make sure to apply alternating waveform by
continuous application of the M signal. Especially the power ON/OFF sequence should be kept to avoid latchup of driver LSIs and DC charge up to LCD panel.
8. Mechanical Considerations
a) LCM are assembled and adjusted with a high degree of precision. Avoid excessive shocks and do not
make any alterations or modifications. The following should be noted.
b) Do not tamper in any way with the tabs on the metal frame.
c) Do not modify the PCB by drilling extra holes, changing its outline, moving its components or modifying its
pattern.
d) Do not touch the elastomer connector; especially insert a backlight panel (for example, EL).
e) When mounting a LCM makes sure that the PCB is not under any stress such as bending or twisting.
Elastomer contacts are very delicate and missing pixels could result from slight dislocation of any of the
elements.
f) Avoid pressing on the metal bezel, otherwise the elastomer connector could be deformed and lose
contact, resulting in missing pixels.
9. Static Electricity
a) Operator
Ware the electrostatics shielded clothes because human body may be statically charged if not ware
shielded clothes. Never touch any of the conductive parts such as the LSI pads; the copper leads on the
PCB and the interface terminals with any parts of the human body.
b) Equipment
There is a possibility that the static electricity is charged to the equipment, which has a function of peeling or friction
action (ex: conveyer, soldering iron, working table). Earth the equipment through proper resistance (electrostatic
earth: 1x108 ohm).
Only properly grounded soldering irons should be used.
If an electric screwdriver is used, it should be well grounded and shielded from commutator sparks.
The normal static prevention measures should be observed for work clothes and working benches; for the latter
conductive (rubber) mat is recommended.
c) Floor
Floor is the important part to drain static electricity, which is generated by operators or equipment.
There is a possibility that charged static electricity is not properly drained in case of insulating floor. Set the
electrostatic earth (electrostatic earth: 1x108 ohm).
d) Humidity
Proper humidity helps in reducing the chance of generating electrostatic charges. Humidity should be kept over
50%RH.
e) Transportation/storage
The storage materials also need to be anti-static treated because there is a possibility that the human body
or storage materials such as containers may be statically charged by friction or peeling.
The modules should be kept in antistatic bags or other containers resistant to static for storage.
f) Soldering
Solder only to the I/O terminals. Use only soldering irons with proper grounding and no leakage.
Soldering temperature : 280°C ± 10°C
Soldering time: 3 to 4 sec.
AZ DISPLAYS
12
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
Use eutectic solder with resin flux fill.
If flux is used, the LCD surface should be covered to avoid flux spatters. Flux residue should be removed
afterwards.
g) Others
The laminator (protective film) is attached on the surface of LCD panel to prevent it from scratches or
stains. It should be peeled off slowly using static eliminator.
Static eliminator should also be installed to the workbench to prevent LCD module from static charge.
10. Operation
a) Driving voltage should be kept within specified range; excess voltage shortens display life.
b) Response time increases with decrease in temperature.
c) Display may turn black or dark blue at temperatures above its operational range; this is (however not
pressing on the viewing area) may cause the segments to appear “fractured”.
d) Mechanical disturbance during operation (such as pressing on the viewing area) may cause the
segments to appear “fractured”.
11. If any fluid leaks out of a damaged glass cell, wash off any human part that comes into contact with soap and
water. The toxicity is extremely low but caution should be exercised at all the time.
12. Disassembling the LCD module can cause permanent damage and it should be strictly avoided.
13. LCD retains the display pattern when it is applied for long time (Image retention). To prevent image retention,
do not apply the fixed pattern for a long time. Image retention is not a deterioration of LCD. It will be removed
after display pattern is changed.
14. Do not use any materials, which emit gas from epoxy resin (hardener for amine) and silicone adhesive agent
(dealcohol or deoxym) to prevent discoloration of polarizer due to gas.
15. Avoid the exposure of the module to the direct sunlight or strong ultraviolet light for a long time.
16.The brightness of LCD module may be affected by the routing of CCFL cables due to leakage to the chassis
through coupling effect. The inverter circuit needs to be designed taking the level of leakage current into
consideration. Thorough evaluation is needed for LCD module and inverter built into its host equipment to ensure
specified brightness.
AZ DISPLAYS
13
ATM2412B SERIES TFT GRAPHIC MODULE VER1.1
Appendix: P/N description
No.
Module P/N
VDD
FONT COLOR
BG COLOR
1
ATM2412B-NLW-BFW
5V
White
Blue
2
ATM2412B-FLW-FFW
5V
Black
White
3
ATM2412B-NLW-FFW
5V
White
Black
4
ATM2412B-FL-YFW
5V
Black
Yellow-Green
5
ATM2412B-NLW-BFW-M
3.3V
White
Blue
6
ATM2412B-FLW-FFW-M
3.3V
Black
White
7
ATM2412B-NLW-FFW-M
3.3V
White
Black
8
ATM2412B-FL-YFW-M
3.3V
Black
Yellow-Green
9
ATM2412B-FLW-XFW
5V
10
ATM2412B-FLW-XFW-M
3.3V
11
Customized
...
AZ DISPLAYS
Remark
Can get No.1~ No.4 display
mode via the switch on PCB board
...
14