︳ CQB100-110S SERIES 100 WATT DC-DC CONVERTERS FEATURES * 100W Isolated Output * Efficiency to 92% * 200KHz Switching Frequency * 3:1 Input Range * Regulated Outputs * Remote ON/OFF * Over Temperature Protection * Over Voltage/Current Protection * Continuous Short Circuit Protection * Quarter Brick Size meet industrial standard * CE Mark Meets 2004/108/EC * UL60950-1 Approval * Meet EN50155 With External Circuits OUTPUT MODEL INPUT INPUT CURRENT OUTPUT CURRENT NUMBER VOLTAGE Capacitor % EFF. VOLTAGE Load max. MIN. MAX. NO LOAD FULL LOAD CQB100-110S05 66-160 VDC 5.0VDC 0mA 20 A 30mA 1010mA 90 10000µF CQB100-110S12 66-160 VDC 12 VDC 0mA 8.4 A 40mA 993mA 92 8800µF CQB100-110S24 66-160 VDC 24 VDC 0mA 4.2 A 60mA 1030mA 91 1500µF NOTE: 1. Nominal Input Voltage 110VDC 1 SPECIFICATIONS All Specifications Typical At Nominal Line, Full Load, and 25℃ Unless Otherwise Noted INPUT SPECIFICATIONS: GENRAL SPECIFICATIONS: Input Voltage Range ....……………........…........ 110V ............... 66-160V Input Surge Voltage (100ms max.) …………..……….…... 180Vdc max. Under voltage lockout ……….........….. power up …..…......………. 62V power down ………...….…. 56V Positive Logic Remote ON/OFF: Logic Compatibility ………………..………... Open Collector ref to -Input Module ON…………… > 3.5Vdc to 75Vdc or Open Circuit Module OFF ………………………………………….. < 1.8Vdc Input Filter ………………………………………………..….……... PI Type Efficiency .................…..................................……..........…....... See Table Isolation Voltage .............. Input/Output, Input/Case .......….. 2250VDC min. Output/Case ………………….… 1500VDC min. 7 Isolation Resistance ..............................…......................…….... 10 ohm min. Isolation Capacitance …………………...……………….…..…… 1000pF typ. Switching Frequency ........…………………............……….…... 200KHz typ. Operating Case Temperature ...………...........….....……........ -40℃ to 100℃ Storage Temperature …………………......……..……............ -55℃ to +105℃ Thermal Shutdown, Case Temp. .………….………….…..……. 105℃ typ. OUTPUT SPECIFICATIONS: Humidity ....................................................... 95% RH max. Non condensing Voltage Accuracy ........................................………….......... ±1.5% max. Transient Response:25% Step Load Change .……………..… <200u sec. External Trim Adj. Range …………………………………….……….. ±10% Ripple & Noise, 20MHz BW(note 3) 5V ……….……….. 40mV RMS, 100mV pk-pk max., 12V …………….…. 60mV RMS., 150mV pk-pk max. 24V ……………..… 100mV RMS, 240mV pk-pk max. Temperature Coefficient ....................………..............…..... ±0.03%/°C MTBF …… MIL-HDBK-217F, GB, 25℃, Full Load …………… TBD hrs typ. nd Safety ………………….…… UL60950-1 2 (Basic insulation), Approval EMC(note 7) ……………… meet EN50155(EN50121-3-2) with external filter Shock/Vibration ……………………..……………… meet EN50155(EN61373) Environmental ………………………….……… meet EN50155(EN60068-2-1) Dimensions ...................……... 2.28×1.45x0.50 inches (57.9x36.8×12.7 mm) Case Material .................................... Aluminum Baseplate with Plastic Case Weight ……………………..……………………………………..………… 61.5 g Short Circuit Protection .........………………......................... Continuous NOTE: Line Regulation (note 1) ……............................................…. ±0.2% max. 1. Measured From High Line to Low Line Load Regulation (note 2) …….......................…….................. ±0.2% max. Over Voltage Protection trip Range ,% Vo nom. .................. 115-140% Current Limit .................……………….... 110% ~180% Nominal Output Start up time ……………………………………………….… 45ms typ. 2. Measured From Full Load to Zero Load 3. Output Ripple and Noise measured with 10uF tantalum and 1uF ceramic capacitor across output 4. Suffix "N" to the Model Number with Negative Logic Remote ON/OFF Module ON ……………………………………………..…. < 1.8Vdc Module OFF ………………….. >3.5Vdc to 75Vdc or Open Circuit 5. Suffix “-C” to the Model Number with Clear Mounting Insert (3.2mm DIA.) 6. An external input capacitor 120uF for all models are recommended to reduce input ripple voltage. 7. Design meet EN50155 and RIA12 refer to Application Note CASE QB All Dimensions In Inches(mm) Tolerances Inches: X.XX= ±0.02 , X.XXX= ±0.010 Millimeters: X.X= ±0.5 , X.XX=±0.25 2.28 [57.9] REMOTE ON/OFF CONTROL 2.000[50.8] ON/OFF (2) Pin 1 2 3 4 5 6 7 8 BOTTOM VIEW 1 0.300[7.62] 2 4 5 6 7 8 0.600[15.24] 3 Function +Vin ON/OFF -Vin -Vout -Sense Trim +Sense +Vout HIGH SIGNAL HERE DISABLE OUTPUT -VIN (4) EXTERNAL OUTPUT TRIM +SENSE (8) 1.86[47.2] 0.059[1.50] 0.16min [4.1] 0.040[1.02] DIA 6PLACES +SENSE (8) TRIM DOWN TRIM (7) DIA 2PLACES TRIM (7) TRIM UP 0.50 [12.7] 1.03[26.2] 0.600[15.24] 1.45 [36.8] Mounting Inserts M3*0.5 Through 2pl. -SENSE (6) 2 -SENSE (6) 10K ohms TRIMPOT