ETC 54F258ADC

MICROCIRCUIT DATA SHEET
Original Creation Date: 04/15/97
Last Update Date: 02/10/98
Last Major Revision Date: 01/13/98
CN54F258A-X REV 1A0
QUAD 2-INPUT MULTIPLEXER WITH TRI-STATE OUTPUTS
General Description
The F258A is a quad 2-Input multiplexer with Tri-State outputs. Four bits of data from
two sources can be selected using a Common Data Select Input. The four outputs present
the selected data in the complement (Inverted) form. The outputs may be switched to a
high impedance state with a HIGH on the common Output Enable (OE) input, allowing the
outputs to interface directly with bus-oriented systems.
Industry Part Number
NS Part Numbers
54F258A
54F258ADC
Prime Die
M258A
Processing
Subgrp Description
1
2
3
4
5
6
7
8A
8B
9
10
11
Quality Conformance Inspection
1
Static tests at
Static tests at
Static tests at
Dynamic tests at
Dynamic tests at
Dynamic tests at
Functional tests at
Functional tests at
Functional tests at
Switching tests at
Switching tests at
Switching tests at
Temp ( oC)
+25
+70
0
+25
+70
0
+25
+70
0
+25
+70
0
MICROCIRCUIT DATA SHEET
CN54F258A-X REV 1A0
Features
-
Multiplexer Expansion By Tying Outputs Together
Inverting Tri-State Outputs
Guaranteed 4000V minimum ESD protection
2
MICROCIRCUIT DATA SHEET
CN54F258A-X REV 1A0
(Absolute Maximum Ratings)
(Note 1)
Storage Temperature
-65 C to +150 C
Ambient Temperature under Bias
-55 C to +125 C
Junction Temperature under Bias
-55 C to +175 C
Vcc Pin Potential to Ground Pin
-0.5V to +7.0V
Input Voltage
(Note 2)
-0.5V to +7.0V
Input Current
(Note 2)
-30mA to +5.0mA
Voltage Applied to Output in HIGH State (with Vcc=0V)
Standard Output
TRI-STATE Output
Current Applied to Output in LOW State (Max)
-0.5V to Vcc
-0.5V to +5.5V
twice the rated Iol(mA)
ESD Last Passing Voltage (Min)
4000V
Note 1:
Note 2:
Absolute Maximum ratings are those values beyond which the device may be damaged or
have its useful life impaired. Functional operation under these conditions is not
implied.
Either voltage limit or current limit is sufficient to protect inputs.
Recommended Operating Conditions
Free Air Ambient Temperature
Commercial
Supply Voltage
Commercial
0 C to +70 C
+4.5V to +5.5V
3
MICROCIRCUIT DATA SHEET
CN54F258A-X REV 1A0
Electrical Characteristics
DC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: VCC 4.5V to 5.5V, Temp range: 0C to +70C
SYMBOL
PARAMETER
CONDITIONS
NOTES
PINNAME
VIH
Input HIGH
Voltage
Recognized as a HIGH Signal
1
INPUTS
VIL
Input LOW Voltage
Recognized as a LOW Signal
1
INPUTS
VCD
Input Clamp Diode
Voltage
VCC=4.5V, IIN=-18mA
2, 3 INPUTS
VOH
Output HIGH
Voltage
VCC=4.5V, IOH=-1.0mA
MIN
MAX
2.0
UNIT
SUBGROUPS
V
1, 2,
3
0.8
V
1, 2,
3
-1.2
V
1, 2,
3
2, 3 OUTPUTS 2.5
V
1, 2,
3
VCC=4.5V, IOH=-3.0mA
2, 3 OUTPUTS 2.4
V
1, 2,
3
VCC=4.75V, IOH=-1.0mA
2, 3 OUTPUTS 2.7
V
1, 2,
3
VCC=4.75V, IOH=-3.0mA
2, 3 OUTPUTS 2.7
V
1, 2,
3
VOL
Output LOW
Voltage
VCC=4.5V, IOL=24mA
2, 3 OUTPUTS
0.5
V
1, 2,
3
IIH
Input HIGH
Current
VCC=5.5V, VIN=2.7V
2, 3 INPUTS
5.0
uA
1, 2,
3
IBVI
Input HIGH
Current Breakdown
Test
VCC=5.5V, VIN=7.0V
2, 3 INPUTS
7.0
uA
1, 2,
3
ICEX
Output HIGH
Leakage Current
VCC=5.5V, VOUT = VCC
2, 3 OUTPUTS
100
uA
1, 2,
3
VID
Input Leakage
Test
VCC = 0.0V, IID = 1.9uA,
All other pins grounded
2, 3 INPUTS
V
1, 2,
3
IOD
Output Leakage
Circuit Current
VCC = 0.0V, VIOD = 150mV,
All other pins grounded
2, 3 OUTPUTS
4.75
uA
1, 2,
3
IIL
Input LOW Current
VCC=5.5V, VIN=0.5V
2, 3 INPUTS
-0.6
mA
1, 2,
3
IOZH
Output Leakage
Current
VCC=5.5V, VOUT=2.7V
2, 3 OUTPUTS
50
uA
1, 2,
3
IOZL
Output Leakage
Current
VCC=5.5V, VOUT=0.5V
2, 3 OUTPUTS
-50
uA
1, 2,
3
IOS
Output Short
Circuit Current
VCC=5.5V, VOUT = 0V
2, 3 OUTPUTS -60
-150
mA
1, 2,
3
IZZ
Bus Drainage Test
VCC = 0.0V, VOUT = 5.25V
2, 3
500
uA
1, 2,
3
ICCH
Power Supply
Current
VCC=5.5V, VO = HIGH
2, 3 VCC
9.5
mA
1, 2,
3
ICCL
Power Supply
Current
VCC=5.5V, VO = LOW
2, 3 VCC
23
mA
1, 2,
3
4
4.75
MICROCIRCUIT DATA SHEET
CN54F258A-X REV 1A0
Electrical Characteristics
DC PARAMETERS(Continued)
(The following conditions apply to all the following parameters, unless otherwise specified.)
DC: VCC 4.5V to 5.5V, Temp range: 0C to +70C
SYMBOL
ICCZ
PARAMETER
Power Supply
Current
CONDITIONS
NOTES
VCC=5.5V, VO = HIGH Z
PINNAME
MIN
2, 3 VCC
MAX
17
UNIT
SUBGROUPS
mA
1, 2,
3
AC PARAMETERS
(The following conditions apply to all the following parameters, unless otherwise specified.)
AC: CL=50pf, RL=500 OHMS, TR=2.5ns, TF=2.5ns, Temp Range: 0C to +70C
tpLH(1)
tpHL(1)
tpLH(2)
tpHL(2)
tpZH
tpZL
tpHZ
tpLZ
Propagation Delay
Propagation Delay
Propagation Delay
Propagation Delay
Output Enable
Time
Output Enable
Time
Output Disable
Time
Output Disable
Time
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
VCC=+5.0V @ +25C,
VCC=4.5V & 5.5V @ 0/+70C
2, 3 In to
Zn
2.5
5.3
ns
9
2, 3 In to
Zn
2.0
7.0
ns
10, 11
2, 3 In to
Zn
1.0
4.0
ns
9
2, 3 In to
Zn
1.0
5.0
ns
10, 11
2, 3 S to Zn 3.0
7.5
ns
9
2, 3 S to Zn 3.0
8.5
ns
10, 11
2, 3 S to Zn 2.5
7.0
ns
9
2, 3 S to Zn 2.5
8.0
ns
10, 11
2, 3 OE to
Zn
2.0
6.0
ns
9
2, 3 OE to
Zn
2.0
7.0
ns
10, 11
2, 3 OE to
Zn
2.5
7.0
ns
9
2, 3 OE to
Zn
2.5
8.0
ns
10, 11
2, 3 OE to
Zn
2.0
6.0
ns
9
2, 3 OE to
Zn
2.0
7.0
ns
10, 11
2, 3 OE to
Zn
2.0
6.0
ns
9
2, 3 OE to
Zn
2.0
7.0
ns
10, 11
Note 1:
Note 2:
Guaranteed by applying specific input condition and testing VOL & VOH.
Screen tested 100% on each device at +75C temperature only, subgroups A2, 8A & A10.
Note 3:
Sample tested (Method 5005, Table 1) on each MFG. lot at +75C temperature only,
subgroups A2, 8A & A10.
5
MICROCIRCUIT DATA SHEET
CN54F258A-X REV 1A0
Revision History
Rev
ECN #
Originator
Changes
0A0
M0001739 02/10/98
Rel Date
Linda Collins
Initial MDS Release
1A0
M0002736 02/10/98
Donald B. Miller 1) Deleted "SEE AC FIGS" from the AC parameter
conditions.
2) Changed tpLH(1) maximum limit at 0C
and 70C from 6.0ns to 7.0ns.
3) Added subgroup 8A
to notes 2 and 3.
6