Pneumatic Function Fittings Pilot Operated Check Valve (Blocking Fitting) - 102GA PIF x BSPP thread 12 Product number J E G I D A H 1 C D E G H SQ I J 25,2 26,2 28,2 32,7 39,7 47,5 47,5 54,5 54,5 65,0 17 17 22 22 27 10,5 10,5 10,8 10,8 12,8 20 20 24 24 30 25,8 25,8 29,0 29,0 36,0 M5 M5 M5 M5 M5 1) Inlet Port 2) Outlet Port 12) Signal Port C 2 102GA0628 102GA0828 102GA0838 102GA1038 102GA1248 A B O/D thread tube BSPP 1⁄4" 6 1⁄4" 8 3⁄8" 8 3⁄8" 10 1⁄2" 12 B Note: For mounting in pairs on a cylinder Pilot Operated Check Valve (Blocking Fitting) - 124GA PIF x NPTF thread 12 Product number J E D 124GA0418 124GA0428 124GA0638 124GA0748 C D E G H SQ I J 23,2 25,2 32,7 39,7 41,0 48,0 55,0 65,5 13 17 22 27 12,3 16,3 17,5 22 16 20 24 30 19,8 25,8 29,0 36,0 10-32’’UNF 10-32’’UNF 10-32’’UNF 10-32’’UNF I 1 A H Body B port thread A NPTF 1⁄ 4PIF 1⁄ 8 1⁄ 4PIF 1⁄ 4 3⁄ 8PIF 3⁄ 8 1⁄ 2PIF 1⁄ 2 G 1) Inlet Port 2) Outlet Port 12) Signal Port C 2 B Note: For mounting in pairs on a cylinder Pilot Operated Check Valve (Blocking Fitting) - 124GA NPTF threaded port x NPTF thread 12 J Product number E C D E G H SQ I J 22,0 29,0 30,5 39,0 41,0 48,0 55,0 65,5 13 17 22 27 12,3 16,3 17,5 22 16 20 24 30 19,8 25,8 29,0 36,0 10-32’’UNF 10-32’’UNF 10-32’’UNF 10-32’’UNF G I D A H 1 Body B port thread A NPTF 1 124GA1818 ⁄ 8NPTF 1⁄ 8 124GA2828 1⁄ 4NPTF 1⁄ 4 124GA3838 3⁄ 8NPTF 3⁄ 8 124GA4848 1⁄ 2NPTF 1⁄ 2 C 2 B 1) Inlet Port 2) Outlet Port 12) Signal Port Note: For mounting in pairs on a cylinder Warning These products are intended for use in industrial compressed air systems only. Do not use these products where pressures and temperatures can exceed those listed under ‘Technical Data’. Before using these products with fluids other than those specified, for non-industrial applications, life-support systems, or other applications not within published specifications, consult Norgren. Through misuse, age, or malfunction, components used in fluid power systems can fail in various modes. The system designer is warned to consider the failure modes of all component parts used in fluid power systems and to provide adequate safeguards to prevent personal injury or damage to equipment in the event of such failure. System designers must provide a warning to end users in the system instructional manual if protection against a failure mode cannot be adequately provided. System designers and end users are cautioned to review specific warnings found in instruction sheets packed and shipped with these products where applicable. N/AL 9.11.002.02 Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. 06/97 Pneumatic Function Fittings Metric & Inch Pilot Operated Check Valve (Blocking Fitting) ● Very compact units ● Easy tube insertion for rapid assembly of pneumatic circuits ● Positive tube anchorage ● Safer pneumatic systems Technical Data Medium: Compressed air Operating Pressure: 1 - 10 bar Ordering Information To order, quote appropriate product number from the tables on the following pages. Operating Temperature: –20°C to +80°C Inlet Port: 6, 8, 10, 12mm Push-in Fittings 1⁄ 4, 3⁄ 8, 1⁄ 2 Push-in Fittings 1⁄ 8, 1⁄ 4, 3⁄ 8, 1⁄ 2 NPTF Threaded Ports Product numbering system is designed to make identification and selection simple: Outlet Port: 1 0 1⁄ 4, 3⁄ 8, 1⁄ 2 BSPP Thread 1⁄ 8, 1⁄ 4, 3⁄ 8, 1⁄ 2 NPTF Thread Signal Port: Shape Series Number Type M5 10-32’’ UNF Thread Size/ Tube Size Tube Size/ Thread Size Tube Sizes 6, 8, 10, 12mm O/D 1⁄ 4, 3⁄ 8 ,1⁄ 2 O/D 102GA 124GA Tubing Types: Nylon 11 or 12, polyurethane and other plasticised or unplasticised tubing which conforms to the tolerances specified in BS 5409, Part 1, 1976, light and normal duty, DIN 73378, DIN 74234, NFE 49-100 12 2 1 Materials Nickel plated brass body Nickel plated brass collet Plastic sealing washer Nitrile and polyurethane elastomeric parts Zinc plated brass banjo bolts 06/97 Our policy is one of continuous research and development. We therefore reserve the right to amend, without notice, the specifications given in this document. N/AL 9.11.002.01