Communication ICs DTMF receiver for telephones BU8874 / BU8874F The BU8874 and BU8874F are DTMF receiver ICs developed for use in telephone answering machines, and convert 16 different types of DTMF signals into 4-bit binary serial data. In addition to a compact 8-pin DIP (BU8874) package, these receivers feature a wide dynamic range, eliminating the need for an external input amplifier. Expertise from a number of companies has been incorporated into these products to enable guard time control through a host microcontroller. Applications Telephone answering machines Features 1) Dynamic range of 45dB. (internal AGC) 2) Power down mode. 3) 4-bit binary serial data output. 4) Guard time can be controlled through host microcontroller. 5) Input pins equipped with hysteresis. (ACK pin) Block diagram 202 6) 4.19MHz crystal resonator can be used. 7) 8-pin DIP package. (BU8874) Communication ICs BU8874 / BU8874F FAbsolute maximum ratings (Ta=25_C) FRecommended operating conditions (Ta=25_C) FPin descriptions 203 Communication ICs BU8874 / BU8874F Input / output circuits INPUT PWDN OSC ACK SD ESt 204 Communication ICs BU8874 / BU8874F FElectrical characteristics (unless otherwise noted, Ta=25_C, VDD=5.0V) 205 Communication ICs Circuit operation (1) An overview of operation A DTMF signal is supplied to the INPUT pin and applied to a pair of 6th-order bandpass filters, which separate the DTMF signal into its high (COL) and low (ROW) frequencies. The separated tonesre converted into square waves and fed to a DIGITAL DETECTOR. The DIGITAL DETECTOR checks the two tones to see if they are within the valid DTMF frequency bands. If they are, it sends a DETECT signal to the STEERING CIRCUIT, and sends the appropriate COLUMN and ROW address signals to a CODE CONVERTER. The CODE CONVERTER encodes the received and detected DTMF signal, and outputs an ENABLE signal to the STEERING CIRCUIT. Based on the DETECT and ENABLE signals, the STEERING CIRCUIT outputs an Early Steering (ESt) signal, which sets the ESt pin to HIGH, indicating that a valid DTMF signal has been detected. If a series of pulses is input at the ACK pin while ESt is HIGH, a decoded DTMF signal is output to the SD pin as a binary code. (See Figure 4 for the overall timing.) If a pulse sequence is input at the ACK pin, the data is latched at the rising edge of the first pulse by a PARALLELSERIAL CONVERTER, and at the same time, the LSB is output from the SD pin. Following this, three bits of data are output from the SD pin for each bit of each pulse in the pulse sequence input from the ACK pin. As a result, a total of four bits of data are output for the four pulses. (See Figure 5 for the ACK and SD timing.) If the pulse sequence input to the ACK pin consists of three or fewer pulses, the next DTMF input cannot be decoded properly. Any ACK pulses in excess of four are ignored until ESt goes HIGH again. Table 1 shows the format of serial data output from the SD pin. BU8874 / BU8874F (2) Power down interface The power down mode is activated by applying a rising edge at the PWDN pin when the ACK pin is LOW. The ACK pin may be taken from LOW to HIGH and back to LOW again while the circuit is in the power down mode. To return to the normal operation mode, set PWDN to LOW. After returning from the power down mode to the normal operation mode, if a valid DTMF signal is still being held (from prior to entering the power down mode), a second reading of the data can be performed (the first reading following recovery to the normal operation mode) by inputting the ACK pulse sequence. Figure 3 shows this status. If the circuit enters the power down mode n times, data can be read (n1) times (while ESt is HIGH), as long as input of the DTMF signal continues. 206 Communication ICs BU8874 / BU8874F (3) Overall timing chart (5) ACK and SD timing (4) Serial data correspondence table (6) Operation mode input logic 207 Communication ICs BU8874 / BU8874F Application example Selecting attachment components (1) Power supply components C502 : This is the VDD bypass capacitor, and is normally 100µF. JP501 : This is normally shorted. To test the current consumption of the IC (at the point where the power down mode is entered), insert a DC ammeter in place of JP501. (2) Oscillation components X501 : Use a crystal or ceramic resonator with an oscillation frequency of 4.194304MHz. If using a ceramic resonator, there may be problems with the precision of the oscillation frequency, so we recommend using one of the ceramic resonators listed below. 208 C591 : If you are using a dedicated resonator X501designed for DTMF receivers, capacitor C591 should be left open. If you are injecting an external clock, X501 should be omitted and DC blocking capacitor C591 used in its place. Typically, this capacitor should be 47µnF. Communication ICs BU8874 / BU8874F (3) DTMF input C501 : This is the DC blocking capacitor. Select a capacitor that will pass DTMF signals (greater than 697Hz) without significantly attenuating the signals. JP592 : If DTMF signals are being input directly, both ends should be shorted. Q591 Use these to increase the sensitivity of R591 X R595 the DTMF receiver. C592, C593 (4) ESt output The ESt guard time is determined by the CPU of the host computer, but to reduce the load on the host computer, the guard time can be set using an external circuit, as shown in Figure 10. The relation between a momentary falter in the ESt guard time (tGL), a momentary HIGH level in the ESt guard time (tGH), and the time constant is shown below. Figure 12 shows a timing diagram for guard times. 209 Communication ICs Operation notes (1) Power down When ACK is LOW, the power down mode can be entered by applying a rising edge to the PWDN pin. Current consumption drops from several seconds to several tens of seconds after the power down mode has been specified. Operation with SD multiple reading is recommended. BU8874 / BU8874F (2) Oscillation Oscillation frequency precision can be a problem with ceramic resonators. Before including a ceramic resonator in your design, please consult the resonator manufacturer to make sure this will not be a problem. Also, if an external clock is being injected, a DC blocking capacitor must be inserted. Select a capacitor that will neither attenuate the frequency components or put an excessive load on the drive side. This LSI is not equipped with the power-on reset function. Also, since the internal circuit (flip-flop circuit) becomes unstable at the rising edge of the power supply, the internal circuit is initialized as shown below by the first DTMF sequence received after the rising edge of the power supply. Therefore, input four dummy ACK pulses before the DTMF reception. Electrical characteristic curves 210 Communication ICs BU8874 / BU8874F External dimensions (Units: mm) 211