SONY CXD1803AR

CXD1803AQ/AR
CD-ROM DECODER
For the availability of this product, please contact the sales office.
Description
CXD1803AQ/AR is a CD-ROM decoder LSI with a
built-in ADPCM decoder.
Features
• Compatible with CD-ROM, CD-I and CD-ROM XA
formats
• Real time error correction
• Capable of handling up to quadruple speed
playback
• Connectable with standard SRAM of up to 2M-bit
(256K-byte)
• Connectable with standard DRAM of up to 2M-bit
(256K-byte)
•
•
•
•
(2 DRAM's of 256K × 4)
All audio output sampling frequencies: 132.3 KHz
(built-in oversampling filter)
De-emphasis digital filter
Digital attenuator
Connectable directly with Sony's SCSI controller
CXD1185CQ.
CXD1803AQ
CXD1803AR
100 pin QFP (Plastic) 100 pin LQFP (Plastic)
Absolute Maximum Ratings (Ta=25°C)
• Supply voltage
VDD
–0.5 to +7.0
• Input voltage
VI
–0.5 to VDD +0.5
• Output voltage
VI
–0.5 to VDD +0.5
• Operating temperature Topr
–20 to +75
• Storage temperature Tstg
–55 to +150
V
V
V
°C
°C
Recommended Operating Conditions
• Supply voltage
VDD
+3.5 to +5.5 (+5.0 typ.) V
• Operating temperature Topr
–20 to +75
°C
Applications
CD-ROM drives
Structure
Silicon gate CMOS IC
Sony reserves the right to change products and specifications without prior notice. This information does not convey any license by
any implication or otherwise under any patents or other right. Application circuits shown, if any, are typical examples illustrating the
operation of the devices. Sony cannot assume responsibility for any problems arising out of the use of these circuits.
—1—
E94Y31-TE
—2—
XRST
HCLK
CLK
RMCK
89
81
80
83
82
77
XTL1
CKSL
76
87
XTL2
C2PO
86
85
DATA
BCLK
84
LRCK
4, 9
15,21
29,35
40,47
54,60
65,71
79,90
XME1
XME0
C
L G
O E
C N
K
CDP I/F
D0-7
1,2,5–8,10,11
PRIORITY
RESOLVER
17–20,22
A0-A4
XWR
XINT
XRD
12 13 14 16
XCS
63 64
XMOE
XMWR
DMA
SEQUENCER
CORRECTOR
ECC
Sub CPU I/F
SYNDROME GEN
GALOIS FIELD
21
DRAM
SYNC CONTROL
DESCRAMBLER
ADDRESS GEN
39,41—46,48—52,55,56,58,59,61 57 62
MA0-16
The pin numbers in the diagram are for the CXD1803AQ.
GND
VDD
3
28
53
78
Block Diagram
MDB0-7,P
91 92 93 94 95
DAC I/F
DIGITAL FILETER
ADPCM DECODER
HOST I/F
DMA FIFO
EMP DATO WCKO MUTE
LRCO BCKO
88
66—70,72—75
23
96
| TD0-5
100
37 SDRQ
XSAC
38
25 XSWR
24 XSRD
26
27 SD0-7
30
|
34
36
CXD1803AQ/AR
CXD1803AQ/AR
Pin Description
Pin No.
Q
R
Symbol
I/O
D0
I/O
Description
1
99
Sub CPU data bus
2
100
D1
I/O
Sub CPU data bus
3
1
VDD
—
Power supply (+5 V)
4
2
GND
—
Ground
5
3
D2
I/O
Sub CPU data bus
6
4
D3
I/O
Sub CPU data bus
7
5
D4
I/O
Sub CPU data bus
8
6
D5
I/O
Sub CPU data bus
9
7
GND
—
Ground
10
8
D6
I/O
Sub CPU data bus
11
9
D7
I/O
Sub CPU data bus
12
10
XCS
I
IC select negative logic signal from sub CPU
13
11
XRD
I
Strobe negative logic signal to read this IC internal register from sub CPU
14
12
XWR
I
15
13
GND
—
Ground
16
14
XINT
O
Interrupt request negative logic signal from IC to sub CPU
17
15
A0
I
Sub CPU address
18
16
A1
I
Sub CPU address
19
17
A2
I
Sub CPU address
20
18
A3
I
Sub CPU address
21
19
DRAM
I
Memory type selection signal. High: DRAM, Low: SRAM
22
20
A4
I
Sub CPU address
23
21
TD0
I/O
Test input/output
24
22
XSRD
O
Strobe negative logic signal to read SCSI controller internal register
25
23
XSWR
O
Strobe negative logic signal to write SCSI controller internal register
26
24
SD0
I/O
SCSI controller data bus
27
25
SD1
I/O
SCSI controller data bus
28
26
VDD
—
Power supply (+5 V)
29
27
GND
—
Ground
30
28
SD2
I/O
SCSI controller data bus
31
29
SD3
I/O
SCSI controller data bus
32
30
SD4
I/O
SCSI controller data bus
33
31
SD5
I/O
SCSI controller data bus
34
32
SD6
I/O
SCSI controller data bus
Strobe negative logic signal to write this IC internal register from sub CPU
—3—
CXD1803AQ/AR
Pin No.
Q
R
Symbol
I/O
Description
35
33
GND
—
Ground
36
34
SD7
I/O
SCSI controller data bus
37
35
SDRQ
I
SCSI data request positive logic signal
38
36
XSAC
O
SCSI acknowledge negative logic signal
39
37
MA0
O
Buffer memory address (LSB)
40
38
GND
—
Ground
41
39
MA1
O
Buffer memory address
42
40
MA2
O
Buffer memory address
43
41
MA3
O
Buffer memory address
44
42
MA4
O
Buffer memory address
45
43
MA5
O
Buffer memory address
46
44
MA6
O
Buffer memory address
47
45
GND
—
Ground
48
46
MA7
O
Buffer memory address
49
47
MA8
O
Buffer memory address
50
48
MA9
O
Buffer memory address
51
49
MA10
O
Buffer memory address
52
50
MA11
O
Buffer memory address
53
51
VDD
—
Power supply (+5 V)
54
52
GND
—
Ground
55
53
MA12
O
Buffer memory address
56
54
MA13
O
Buffer memory address
57
55
XME0
O
Memory chip enable negative logic signal
58
56
MA14
O
Buffer memory address
59
57
MA15
O
Buffer memory address
60
58
GND
—
Ground
61
59
62
60
63
61
64
62
XMWR
O
Buffer memory write enable negative logic signal
65
63
GND
—
Ground
66
64
MDB0
I/O
Buffer memory data bus
67
65
MDB1
I/O
Buffer memory data bus
MA16
XRAS
XME1
XMOE
XCAS
O
O
O
Buffer memory address
DRAM RAS signal
Memory chip enable negative logic signal
Buffer memory output enable negative logic signal
DRAM CAS signal
—4—
CXD1803AQ/AR
Pin No.
Q
R
Symbol
I/O
Description
68
66
MDB2
I/O
Buffer memory data bus
69
67
MDB3
I/O
Buffer memory data bus
70
68
MDB4
I/O
Buffer memory data bus
71
69
GND
—
Ground
72
70
MDB5
I/O
Buffer memory data bus
73
71
MDB6
I/O
Buffer memory data bus
74
72
MDB7
I/O
Buffer memory data bus
75
73
MDBP
I/O
Buffer memory data bus (for error flag)
76
74
XTL2
O
Crystal oscillation circuit output
77
75
XTL1
I
Crystal oscillation circuit input (16.9344 MHz)
78
76
VDD
—
Power supply (+5 V)
79
77
GND
—
Ground
80
78
CLK
O
16.9344 MHz clock output
81
79
HCLK
O
8.4672 MHz clock output
82
80
CKSL
I
Clock select signal for CD-ROM decoder
83
81
RMCK
I
Clock signal for CD-ROM decoder
84
82
LRCK
I
LR clock signal from CD DSP (for discriminating L, R channels )
85
83
DATA
I
Data signal from CD DSP
86
84
BCLK
I
DATA pin strobe clock signal (bit clock)
87
85
C2PO
I
Error flag (C2 pointer) positive logic signal from CD DSP
88
86
EMP
I
Emphasis on positive logic signal from CD DSP
89
87
XRST
I
Reset negative logic signal
90
88
GND
—
Ground
91
89
DATO
O
Data signal to DAC (D/A converter)
92
90
LRCO
O
LR clock signal to DAC
93
91
WCKO
O
Word lock signal to DAC
94
92
BCKO
O
Bit clock signal to DAC
95
93
MUTE
O
Mute positive logic signal
96
94
TD5
I/O
Test input/output
97
95
TD4
I/O
Test input/output
98
96
TD3
I/O
Test input/output
99
97
TD2
I/O
Test input/output
100
98
TD1
I/O
Test input/output
Note:
The pin numbers in the column "Q" are for the CXD1803AQ, and those in the column "R" are for the
CXD1803AR.
—5—
CXD1803AQ/AR
Electrical Characteristics
DC Characteristics
Item
TTL input level pin ∗1
High level input voltage
TTL input level pin ∗1
Low level input voltage
CMOS input level pin ∗2
High level input voltage
CMOS input level pin ∗2
Low level input voltage
CMOS Schmitt input level pin ∗3
High level input voltage
CMOS Schmitt input level pin ∗3
Low level input voltage
CMOS Schmitt input level pin ∗3
Input voltage hysteresis
TTL Schmitt input level pin ∗4
High level input voltage
TTL Schmitt input level pin ∗4
Low level input voltage
TTL Schmitt input level pin ∗4
Input voltage hysteresis
Bidirectional pin with pull-up resistor ∗5
Input current
Pin with pull-up resistor ∗6
Input current
High level output voltage ∗7
Low level output voltage ∗7
(VDD = 5 V ± 10%, VSS = 0 V, Topr = –20 - 75°C)
Symbol
0.7VDD
0.8VDD
0.2VDD
0.6
V
0.8V
VIL5
VIH4 to VIL4
V
V
2.2V
VIH5
V
V
VIL4
VIH4 to VIL4
V
V
0.3VDD
VIH4
Unit
V
VIL2
0.4
V
V
IIL3
VIN=0V
–90
–200
–440
µA
IIL4
VIN=0V
–40
–100
–240
µA
VOH1
IOH=–2mA
VDD-0.8
VOL1
IOL=–4mA
IOZ
Oscillation cell ∗10 high level input voltage
VIH4
Oscillation cell low level input voltage
VIL4
Oscillation cell logic threshold value
LVTH
Oscillation cell feedback resistance value
RFB
Low level output voltage
Max.
0.8
VIH2
Output leakage current ∗9
Oscillation cell
Typ.
VIL1
II1
High level output voltage
Min.
2.2
VIH1
Input leakage current ∗8
Oscillation cell
Conditions
VIN=VSS
or VDD
High-impedance
state
V
0.4
V
–10
10
µA
–40
40
µA
0.7VDD
V
0.3VDD
0.5VDD
VIN=VSS
or VDD
VOH2
IOH=–3mA
VOL2
IOL=3mA
—6—
250K
1M
V
V
2.5M
0.5VDD
Ω
V
0.5VDD
V
CXD1803AQ/AR
DC Characteristics
(VDD = 3.5 V, VSS = 0 V, Topr = –20 - 75°C)
Item
TTL input level pin ∗1
High level input voltage
TTL input level pin ∗1
Low level input voltage
CMOS input level pin ∗2
High level input voltage
CMOS input level pin ∗2
Low level input voltage
CMOS Schmitt input level pin ∗3
High level input voltage
CMOS Schmitt input level pin ∗3
Low level input voltage
CMOS Schmitt input level pin ∗3
Input voltage hysteresis
TTL Schmitt input level pin ∗4
High level input voltage
TTL Schmitt input level pin ∗4
Low level input voltage
TTL Schmitt input level pin ∗4
Input voltage hysteresis
Bidirectional pin with pull-up resistor ∗5
Input current
Pin with pull-up resistor ∗6
Input current
High level output voltage ∗7
Low level output voltage ∗7
Symbol
0.7VDD
0.8VDD
0.2VDD
0.5
V
0.6V
VIL5
VIH5 to VIL4
V
V
2.2V
VIH5
V
V
VIL4
VIH4 to VIL4
V
V
0.3VDD
VIH4
Unit
V
VIL2
0.3
V
V
IIL3
VIN=0V
–20
–50
–110
µA
IIL4
VIN=0V
–10
–25
–60
µA
VOH1
IOH=–1.6mA
VDD-0.8
VOL1
IOL=3.2mA
IOZ
Oscillation cell ∗10 high level input voltage
VIH4
Oscillation cell low level input voltage
VIL4
Oscillation cell logic threshold value
LVTH
Oscillation cell feedback resistance value
RFB
Low level output voltage
Max.
0.6
VIH2
Output leakage current ∗9
Oscillation cell
Typ.
VIL1
II1
High level output voltage
Min.
2.2
VIH1
Input leakage current ∗8
Oscillation cell
Conditions
VIN=VSS
or VDD
High-impedance
state
V
0.4
V
–10
10
µA
–40
40
µA
0.7VDD
V
0.3VDD
0.5VDD
VIN=VSS
or VDD
VOH2
IOH=–1.3mA
VOL2
IOL=1.3mA
—7—
1.2M
2.5M
V
V
5M
0.5VDD
Ω
V
0.5VDD
V
CXD1803AQ/AR
∗1.
∗2.
∗3.
∗4.
∗5.
∗6.
∗7.
∗8.
∗9.
∗10.
D7 to 0, A4 to 0, XWR, XRD, XCS, MDB7 to 0, MDBP, SD7 to 0, TD7 to 0
DATA, LRCK, C2PO, EMP, CKSL, RMCK
BCLK, XRST
A4 to 0, XWR, XRD, XCS, SDRQ
D7 to 0, MDB7 to 0, MDBP, SD7 to 0, TD7 to 0
CKSL
All output pins except XTL2
All input pins except ∗5, ∗6, and XTL1
HINT
Input: XTL1, Output: XTL2
I/O Capacitance
(VDD = VI = 0 V, f = 1 MHz)
Item
Input pin
Output pin
I/O pin
Symbol
CIN
COUT
COUT
—8—
Min.
Typ.
Max.
9
11
11
Unit
pF
pF
pF
CXD1803AQ/AR
AC Characteristics (VDD = 5 V±10%, VSS = 0 V, Topr = –20 to 75°C, output load = 50 pF)
The values in parentheses on the tables for VDD = 3.5 V, VSS = 0 V, Topr = –20 to 75°C, output load = 50 pF.
Those without parentheses for VDD = 5 V±10% and 3.5 V.
1. Sub CPU Interface
(1) Read
A0
Thar
XCS
Trrl
XRD
D7-0
Tsar
Item
Address setup time (for XCS & XRD ↓)
Address hold time (for XCS & XRD ↑)
Data delay time (for XCS & XRD↓)
Data float time (for XCS & XRD ↑)
Low level XRD pulse width
Tdrd
Tfrd
Symbol
Tsar
Thar
Tdrd
Tfrd
Trrl
Min.
30 (70)
20 (50)
Typ.
Max.
60 (100)
15 (25)
0
100 (150)
Unit
ns
ns
ns
ns
ns
Note) "&" indicates "AND".
(2) Write
A0
XCS
Thaw
Twwl
XWR
D7-0
Tsdw
Tsaw
Item
Address setup time (for XCS & XWR ↓)
Address hold time (for XCS & XWR ↑)
Data setup time (for XCS & XWR ↓)
Data hold time (for XCS & XWR ↑)
Low level XWR pulse width
Symbol
Tsaw
Thaw
Tsdw
Thdw
Twwl
—9—
Min.
30 (70)
20 (50)
40 (70)
10 (30)
50 (80)
Thdw
Typ.
Max.
Unit
ns
ns
ns
ns
ns
CXD1803AQ/AR
2. CD DSP Interface
BCKRED='H'
Tbck
Tbck
BCLK
DATA
Tsb1
Thb1
LRCK
C2PO
Tsb2
Thb2
BCKRED='L'
Tbck
Tbck
BCLK
DATA
Tsb1
Thb1
LRCK
C2PO
Item
BCLK frequency
BCLK pulse width
DATA setup time (for BCLK)
DATA hold time (for BCLK)
LRCK, C2PO setup time (for BCLK)
LRCK, C2PO hold time (for BCLK)
Tsb2
Thb2
Symbol
Fbck
Tbck
Tsb1
Thb1
Tsb2
Thb2
—10—
Min.
88
20
20
20
20
Typ.
Max.
11.3
Unit
MHz
ns
ns
ns
ns
ns
CXD1803AQ/AR
3. DRAM Interface
(1) Read
Trc
Tras
XRAS
Trcd
Tcas
XCAS
Tasr
MA9-0
Trah
Tasc
Row
Tcah
Column
XMWR
Tcdd
Tcdh
Trdd
MDB7-0, P
(2) Write
Trc
Tras
XRAS
Trcd
Tcas
XCAS
Tasr
MA9-0
Row
Trah
Tasc
Tcah
Column
Twcs
Twch
XMWR
Tds
MDB7-0, P
—11—
Tdh
'H'
CXD1803AQ/AR
Item
Random read/write cycle time
RAS pulse width
RAS CAS delay time
CAS pulse width
Row address setup time
Row address hold time
Column address setup time
Column address hold time
Delay time from RAS
Delay time from CAS
Hold time from CAS
Write command setup time
Write command hold time
Data output setup time
Data output hold time
Symbol
Trc
Tras
Trcd
Tcas
Tasr
Trah
Tasc
Tcah
Trdd
Tcdd
Tcdh
Twcs
Twcs
Tds
Tds
—12—
Min.
Typ.
4Tw
Max.
2Tw
Tw
Tw
10
20
0
20
2Tw-20
Tw-20
0
10
20
Tw
Tw
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CXD1803AQ/AR
4. SRAM Interface
(1) Read
MA16-0
Taso
Thoa
Trrl
XMOE
Tsdo
Thod
MDB7-0,P
XMWR='H'
Item
Address setup time (for XMOE ↓)
Address hold time (for XMOE ↑)
Data setup time (for XMOE ↑)
Data hold time (for XMOE ↑)
Low level XMOE pulse width
Symbol
Tsao
Thoa
Tsdo
Thod
Trrl
Min.
Tw-30
Tw-10
50 (100)
10 (20)
Typ.
Max.
Unit
ns
ns
ns
ns
ns
Max.
Unit
ns
ns
ns
ns
ns
2Tw
(2) Write
MA16-0
Tsaw
Thwa
Twwl
XMWR
Tdwd
Tfwd
MDB7-0,P
XMOE='H'
Item
Address setup time (for XMWR ↓)
Address hold time (for XMWR ↑)
Data delay time (for XMWR ↓)
Data float time (for XMWR ↑)
Low level XMMR pulse width
Symbol
Tsaw
Thwa
Tdwd
Tfwd
Twwl
—13—
Min.
Tw-30
Tw-10
Typ.
10
10
2Tw
CXD1803AQ/AR
5. SCSI Controller Interface
(1) Read
Tsdq
SDRQ
Tdda
Tasc
Tdar
Twwl
XSAC
Tdaw
Trrl
XSRD
SD7 to 0
Tsdr
Item
XSAC fall time (for SDRQ ↑)
XSRD delay time (for XSAC ↓)
XSAC delay time (for XSRD ↑)
Data setup time (for XSRD ↓)
Data hold time (for XSRD ↑)
Low level XSRD pulse width
SDRQ setup time (for XSAC ↑)
XSAC fall time (for XSAC ↑)
Symbol
Tdda
Tdaw
Tdar
Tsdr
Thdr
Trrl
Tsdq
Tsac
—14—
Min.
Thdr
Typ.
0
Tw
20 (60)
10 (30)
T1
15 (30)
Tw
Max.
Unit
5×Tw
ns
ns
ns
ns
ns
ns
ns
ns
CXD1803AQ/AR
(2) Write
Tsdq
SDRQ
Tdda
Tsac
Tdwa
XSAC
Twwl
XSWR
Tdaw
SD7 to 0
Tsdr
Item
XSAC fall time (for SDRQ ↑)
XSWR delay time (for XSAC ↓)
XSAC delay time (for XSWR ↑)
Data setup time (for XSWR ↑)
Data hold time (for XSWR ↑)
Low level XSWR pulse width
SDRQ setup time (for XSAC ↑)
XSAC fall time (for XSAC ↑)
Symbol
Tdda
Tdaw
Tdwa
Tsdr
Thdr
Twwl
Tsdq
Tsac
Here:
2×Tw: 3cyclemode
T1= 3×Tw: 4cyclemode
4×Tw: 5cyclemode



Tw: 3cyclemode
T2= 2×Tw: 4cyclemode
3×Tw: 5cyclemode
Tw is the CD-ROM decoder clock cycle.



—15—
Min.
Thdr
Typ.
Tw
Tw
2×Tw-30
Tw-10
T2
15 (30)
Tw
Max.
5×Tw
Unit
ns
ns
ns
ns
ns
ns
ns
ns
CXD1803AQ/AR
6. DAC Interface
Tbco
Tbco
BCKO
DATO
Tsbo
Thbo
WCKO
LRCO
Tsbo
Thbo
Item
BCKO frequency
BCKO pulse width
DATO, WCO1, WCO2, LRCO setup time
(for BCKO ↑)
DATO, WCO1, WCO2, LRCO hold time
(for BCKO ↑)
Symbol
Fbco
Tbco
Min.
50
Unit
MHz
ns
Tsbo
30
ns
Thbo
30
ns
—16—
Typ.
8.4672
Max.
CXD1803AQ/AR
7. XTL1 and XTL2 Pins
(1) For self-excited oscillation
Item
Oscillation frequency
Symbol
Fmax
Min.
Typ.
16.9344
Max.
Unit
MHz
(2) When a pulse is input to XTL1 pin
Tw
Twhx
Twlx
Vihx
Vihx∗0.9
Vdd/2
Vilx∗2
Vilx
Tr
Item
High level pulse width
Low level pulse width
Pulse cycle
Input high level
Input low level
Rise time
Fall time
Note:
Tf
Symbol
Twhx
Twlx
Tw
Vihx
Vilx
Tr
Tf
Min.
20
20
Typ.
Max.
59
VDD-1.0
0.8
15
15
Unit
ns
ns
ns
ns
ns
ns
ns
Synchronize the XTL1 clock signal with that of the CD DSP. (Use the clock signal from the
same oscillator.)
8. RMCK Pin
Item
Frequency
Note:
Symbol
frmck
Min.
Typ.
Max.
33.3 (23.4)
Unit
MHz
The maximum RMCK frequency is 35.0 MHz, when VDD = 5 V ±5%, Playback at quadruple
normal speed can be accommodated when a clock signal with a frequency double 16.9344
MHz or more is input to RMCK.
—17—
CXD1803AQ/AR
Description of Functions
1. Pin Description
The pin description by function is given below.
1.1.CD player interface (5 pins)
This enables direct connection with the digital signal processor LSI for Sony's CD players. Digital signal
processor LSI for CD applications are hereafter called "CD DSP". See 2-1-1 for the data formats.
(1) DATA (DATA: input)
Serial data stream from CD DSP.
(2) BCLK (bit clock: input)
Bit clock signal; data signal strobe.
(3) LRCK (LR clock: input)
LR clock signal; indicates left and right channels of DATA signals.
(4) C2PO (C2 pointer: input)
C2 pointer signal; indicates that an error is contained in DATA input.
(5) EMP (emphasis: input)
Emphasis positive logic signal; indicates that emphasis has been applied to data from CD DSP.
1.2.Buffer memory interface (30 pins)
This is connected with a 32K-byte (256K-bit) or 128K-byte (1M-bit) standard SRAM; also connected with
256K-byte standard DRAM (two DRAMs of 128K-byte).
(1) XMWR (buffer memory write: output)
Data write strobe negative logic output signal to buffer memory.
(2) XMOE/XCAS (buffer memory output enable/column address strobe: output)
When connected to SRAM, data read strobe negative logic output signal to buffer memory.
When connected to DRAM, XCAS (column address strobe negative logic) signal.
(3) MA0 to 15 (buffer memory address: output)
Address signals to buffer memory. When connected to DRAM, MA0 to 8 are valid.
(4) MA16/XRAS (buffer memory address/row address strobe: output)
When connected to SRAM, address signal to buffer memory. XRAS (row address strobe negative
logic) signal when connected to DRAM.
(5) XME0, 1 (buffer memory chip enable: output)
When connected to a chip SRAM, chip enable negative logic signal to buffer memory. Not used when
connected to DRAM.
(6) MDB0 to 7, P (buffer memory data bus: bus)
Data bus signals to buffer memory; pulled up by standard 25kΩ resistor; MDBP pin is left open when
connected to an 8-bit/word SRAM.
(7) DRAM (buffer memory DRAM: input)
High is input when DRAM is connected as buffer memory.
Low is input when SRAM is connected as buffer memory.
—18—
CXD1803AQ/AR
1.3.Sub CPU interface (17 pins)
(1) XWR (sub CPU write: input)
Strobe negative logic input signal for writing IC internal register.
(2) XRD (sub CPU read: input)
Strobe negative logic input signal for reading IC internal register status.
(3) D0 to 7 (sub CPU data bus: input/output)
8-bit data bus.
(4) A0 to 4 (sub CPU address: input)
Address signal for selecting IC internal register from sub CPU.
(5) XINT (sub CPU interrupt: output)
Interrupt request negative logic signal to sub CPU.
(6) XCS (chip select: input)
IC select negative logic signal from sub CPU.
1.4.SCSI controller interface (13pins)
(1) SDRQ (SCSI data request: input)
DMA data request positive logic signal from SCSI controller IC.
(2) XSAC (SCSI DMA acknowledge: output)
DMA acknowledge negative logic signal to SCSI controller IC.
(3) XSWR (SCSI write: negative logic output)
Data write strobe output to SCSI controller IC.
(4) XSRD (SCSI read: negative logic output)
Data read strobe output to SCSI controller IC.
(5) SD0 to 7 (SCSI controller bus: input/output)
SCSI controller data bus signal.
1.5.DAC interface (4 pins)
The output format to DAC is shown in Fig. 1-1.
(1) BCKO (bit clock output: output)
Bit clock output signal to D/A converter.
(2) WCKO (word clock output: output)
Word clock output signal to D/A converter.
(3) LRCO (LR clock output: output)
LR clock output signal to D/A converter.
(4) DATO (data output: output)
Data output signal to D/A converter.
—19—
LRCO
WCKO
DATO
BCKO
16
1
2 3
4
1 2 3
MSB
17
6 7
8
LSB
9 10 11 12 13 14 15 16
L CH
Fig. 1-1 Output Format to D/A Converter
4 5
32
1 2
MSB
49
3 4
5 6
9 10 11 12 13 14 15 16
R CH
7 8
64
CXD1803AQ/AR
—20—
CXD1803AQ/AR
1.6.Others (16 pins)
(1) MUTE (mute: output)
Outputs high when DA data (DATO) is muted.
(2) XRST (reset: input)
Chip reset negative logic input signal.
(3) XTL1 (crystal 1: input)
(4) XTL2 (crystal 2: output)
A 16.9344 MHz crystal oscillator is connected between XTL1 and XTL2. (The capacitor value
depends on the crystal oscillator.)
Alternatively, a 16.9344 MHz clock signal is input to the XTL1 pin.
(5) CLK (cock: output)
Outputs a 16.9344 MHz clock signal. The output can be fixed low when this signal is not used.
(6) HCLK (half clock: output)
Outputs an 8.4672 MHz clock. The output can be fixed low when this signal is not used.
(7) CKSL (clock select: input)
High or open: The IC is operated by the XTL1 clock.
Low:
The audio block (ADPCM decoder and digital filter) is operated by the XTL1 clock,
and the CD-ROM decoder block is operated by the RMCK clock.
This pin is pulled up by a standard 50kΩ resistor in the IC .
(8) RMCK (ROM clock: input)
When the CKSL pin is set low, the clock of the CD-ROM decoder block is input. When it is high or left
open, fix the RMCK pin high or low.
(9) TD0 to 5 (test data 0 to 5: input/output)
Data pins for testing the IC . They are pulled up by a 25kΩ standard resistor and are normally left
open.
—21—
CXD1803AQ/AR
2. Sub CPU Registers
2.1.Write registers
2.1.1. DRVIF (drive interface) register
This register controls the connection mode with the CD DSP. After the IC is reset, the sub CPU sets
this register according to the CD DSP to be connected.
bit 7:
C2PL1ST (C2PO lower byte first)
High: When two bytes of data are input, C2PO inputs the lower byte first followed by the
upper byte.
Low: When two bytes of data are input, C2PO inputs the upper byte first followed by the
lower byte.
Here, "upper byte" means the upper 8 bits including MSB from the CD DSP and "lower
byte" means the lower 8 bits including LSB from the CD DSP. For example, the
header minute byte is the lower byte and the second byte, the upper byte.
bit 6:
LCHLOW (Lch low)
High: When LRCK is low, determined to be the left channel data.
Low: When LRCK is high, determined to be the left channel data.
bit 5:
BCKRED (BCLK rising edge)
High: Data is strobed at the rising edge of BCLK.
Low: Data is strobed at the falling edge of BCLK.
bits 4,3: BCKMD1, 0 (BCLK mode1, 0)
These bits are set according to the number of clocks output for BCLK during one WCLK cycle
by the CD digital signal processing LSI (CD DSP).
BCKMD1
'L'
'L'
'H'
BCKMD0
'L'
'H'
'X'
16BCLKs/WCLK
24BCLKs/WCLK
32BCLKs/WCLK
bit 2:
LSB1ST (LSB first)
High: Connected with the CD DSP which outputs data with LSB first.
Low: Connected with the CD DSP which outputs data with MSB first.
bits 1,0: Reserved
Normally set low.
Any change of each bit in this register must be made in the decoder disable status. Table 2-1-1
indicates the setting values for bits 7 to 2 when this IC is connected to Sony's CD DSP.
Figs. 2-1-1(1) to (3) are input timing charts.
—22—
—23—
C2PO
DATA
BCLK
LRCK
C2PO
DATA
BCLK
LRCK
C2PO
DATA
BCLK
LRCK
L14
31
4
3
5
4
4
6
5
5
7
8
for Upper Byte
6
9
L14
10
3
7
9
L14
10
1
Lch MSB
L15
32
L12
12
13
L11
L10
14
15
L9
16
L8
17
L7
L13
11
L12
12
L11
13
L10
14
L9
15
L8
16
9
10
L6
18
11
12
13
14
15
16
17
R1
19
Rch LSB
R0
18
R2
20
R3
21
R4
22
R5
23
L5
19
R7
25
R8
26
27
L4
20
L4
L3
21
L3
28
21
29
22
30
L2
22
L2
23
31
L1
23
L1
L0
24
1
32
Rch MSB
1
2
Lch LSB
L0
1
Lch LSB
24
R9 R10 R11 R12 R13 R14 R15
for Lower Byte
R6
24
Fig. 2-1-1 (3) CDL40 Series Timing Chart (64-bit slot mode)
for Upper Byte
8
L5
20
for Lower Byte
17
L7
L6
19
for Lower Byte
18
Fig. 2-1-1 (2) CDL40 Series Timing Chart (48-bit slot mode)
Lch MSB
8
L15
2
7
for Upper Byte
6
R0
1
Rch LSB
24
L13
11
Fig. 2-1-1 (1) CDL30 and 35 Series Timing Chart
L15
2
3
Lch MSB
2
R0
1
Rch LSB
24
2
3
2
4
3
3
CXD1803AQ/AR
CXD1803AQ/AR
Table 2-1-1 DRVIF Register Settings
Sony CD DSP
CDL30 Series
CDL35 Series
CDL40 Series
(48-bit slot mode)
CDL40 Series
(64-bit slot mode)
DR VIF register
bit5
bit4
bedg
bck1
bit7
c2po
bit6
lrck
bit3
bck0
bit2
lsb
Timing chart
L
L
L
L
H
L
Fig. 2-1-1(1)
L
L
H
L
H
L
Fig. 2-1-1 (2)
L
H
L
H
X
H
Fig. 2-1-1(3)
Note 1)
CDL30 Series
CDL35 Series
CDL40 Series
CXD1125Q/QZ, CXD1130Q/QZ, CXD1135Q/QZ
CXD1241Q/QZ, CXD1245Q, CXD1246Q/QZ
CXD1247Q/QZ/R, etc.
CXD1165Q, CXD1167Q/QZ/R, etc.
CXD2500Q/QZ, etc.
2.1.2. CONFIG1 (configuration 1) register
This register is set depending on the IC peripheral hardware. The sub CPU sets this register after the
IC is reset.
bit 7:
Reserved
Normally set low.
bit 6:
XSLOW
The number of clock signals per DMA1 cycle is determined by this bit.
High: 4 clock signals
Low: 12 clock signals
Set low when a low-speed SRAM is connected for VDD = 3.5 V.
When XSLOW is low, erasure correction and double speed playback are prohibited.
bit 5:
Reserved
Normally set low.
bits 4,3: RAMSZ1, 0 (RAM size 1, 0)
bit 2:
9BITRAM
These bits are set depending on the size of the buffer memory connected to the IC.
RAMSZ1
'L'
'L'
'L'
'L'
'H'
'H'
'H'
'H'
RAMSZ0
'L'
'L'
'H'
'H'
'L'
'L'
'H'
'H'
9BITRAM
'L'
'H'
'L'
'H'
'L'
'H'
'L'
'H'
Memory size
32KW×8b
32KW×9b
64KW×8b
64KW×9b
128KW×8b
128KW×9b
256KW×8b
256KW×9b
Refer to Chapter 3 for information on buffer memory connection.
—24—
CXD1803AQ/AR
bit 1:
bit 0:
CLKDIS (CLK disable)
High: The CLK pin is fixed low.
Low: A 16.9344 MHz clock signal is output from the CLK pin.
HCLKDIS (half CLK disable)
High: The HCLK pin is fixed low.
Low: An 8.4672 MHz clock signal is output from the HCLK pin.
2.1.3. CONFIG2 (configuration 2) register
This register is set depending on the IC peripheral hardware. The sub CPU sets this register after the
IC has been reset.
bits 7, 6: SCYC1, 0 (SCSI DMA cycle 1, 0)
Data transfer between the IC and the SCSI control IC is executed by the following number of
clock signals.
SCYC1
'L'
'L'
'H'
bit 5:
bit 4:
bit 3:
bit 2:
bit 1:
bit 0:
SCYC0
'L'
'H'
'X'
3 clock signals
4 clock signals
5 clock signals
SPECTL (sound parameter error control)
SPMCTL (sound parameter majority control)
These two bits control the processing of the sound parameters for ADPCM playback.
SMBF2 (sound map buffer 2)
Indicates the number of buffer surfaces for the sound map ADPCM.
High: 2 buffer surfaces for the sound map
Low: 3 buffer surfaces for the sound map
DAMIXDIS (digital audio mixer disable)
High: Attenuator and mixer are not activated for CD-DA.
Low: Attenuator and mixer are activated for CD-DA.
DACOUTEN (DAC out enable)
High: Clock signals are output from the WCKO, LRCO and BCKO pins even for muting.
Low: The WCKO, LRCO and BCKO pins are set low for muting.
PRTYCTL (priority control)
When double speed playback with erasure correction is carried out with the CD-ROM decoder
clock frequency at 18 MHz or less, this bit goes high. In this case, priority is given to buffer
access for ECC, and the data transfer rate to the SCSI controller drops.
—25—
CXD1803AQ/AR
2.1.4. DECCTL (decoder control) register
bit 7:
ENDLADR (enable drive last address)
High: DLADR (drive last address) is enabled when this is set high. When DADRC and
DLADR become equal while the decoder is in the write-only, real-time correction or
CD-DA mode, the data writing from the drive into the buffer is stopped.
Low: DLADR (drive last address) is disabled when this is set low. Even when DADRC and
DLADR become equal while the decoder is in the write-only, real-time correction or
CD-DA mode, the data writing from the drive into the buffer is not stopped.
bit 6:
ECCSTR (ECC strategy)
High: Errors are corrected with consideration given to the error flags of the data.
Low: Errors are corrected with no consideration given to the error flags of the data. In this
case, there is no erasure correction. Set this bit low when the IC is connected to an
8-bit/word SRAM.
bit 5:
MODESEL (mode select)
bit 4:
FORMSEL (form select)
When AUTODIST is low, the sector is corrected in the MODE or FORM indicated below.
MODESEL FORMSEL
'L'
'L'
MODE1
'H'
'L'
MODE2, FROM1
'H'
'H'
MODE2, FROM2
bit 3:
AUTODIST (auto distinction)
High: Errors are corrected according to the MODE byte and FORM bit read from the drive.
Low: Errors are corrected according to the MODESEL and FORMSEL bits (bits 5 and 4).
bits 2 to 0:DECMD2 to 0 (decoder mode 2 to 0)
DECMD2
'L'
'L'
'H'
'H'
'H'
'H'
DECMD1
'L'
'H'
'L'
'L'
'H'
'H'
DECMD0
'X'
'X'
'L'
'H'
'L'
'H'
Decoder disable
Monitor-only mode
Write-only mode
Real-time correction mode
Repeat correction mode
CD-DA mode
When the CD-DA bit (bit 4) in the CHPCTL register is to be set high, set the decoder to the disable or
CD-DA mode.
—26—
CXD1803AQ/AR
2.1.5. DLADR-L
2.1.6. DLADR-M
2.1.7. DLADR-H
While the decoder is in the write-only, real-time correction or CD-DA mode, the last address is set for
the buffer write data from the drive. When the ENDLADR bit (bit 7) of the DECCTL register is high and
the data from the drive is written into the address assigned by DLADR while the decoder is in any of
the above modes, all subsequent writing in the buffer is prohibited.
2.1.8. CHPCTL (chip control) register
bit 7:
SM MUTE (sound map mute)
When this is set high, the audio output is muted for sound map ADPCM playback.
bit 6:
RT MUTE (real time mute)
When this is set high, the audio output is muted for real-time ADPCM playback.
bit 5:
CD-DA MUTE
When bit 4 is high and this bit is also set high for a CD-DA (digital audio) disc playback, the
audio output is muted. When bit 4 is low, this bit has no effect on the audio output.
bit 4:
CD-DA
High: Set high for playing back the audio signals of a CD-DA disc. Setting this bit high is
prohibited for ADPCM decode playback.
Low: Set low for not playing back the audio signals of a CD-DA disc.
bit 3:
SWOPEN (sync window open)
High: A window for sync mark detection is opened. In this case, the sync protection circuit in
the IC is disabled.
Low: The window for sync mark detection is controlled by the sync protection circuit in the
IC.
bit 2:
RPSTART (repeat correction start)
Sector error correction starts when the decoder is set to the repeat correction mode, making
this bit high. This bit is automatically set low when correction starts. Therefore, there
is no need for the sub CPU to reset low.
bit 1:
DBLSPD (double speed)
Set high for double speed playback. Before changing the bit value, switch the CD DSP mode
(normal speed playback or double speed playback).
bit 0:
Reserved
Normally set low.
—27—
CXD1803AQ/AR
2.1.9. WRDATA (CPU buffer write data)
The data written in this register is written in the buffer.
2.1.10. INTMSK (interrupt mask) register
By setting each bit of this register high, the interrupt request from the IC to the sub CPU is enabled
depending on the corresponding interrupt status. (In other words, the INT pin is made active when its
interrupt status is established.) The value of each bit in this register does not affect the corresponding
interrupt status.
bit 7:
DRVOVRN (drive overrun)
The DRVOVRN status is established when the ENDLADR bit (bit 7) of the DECCTL register
is set high, and DADRC and DLADR become equal while the decoder is in the write-only or
real-time correction mode. It is also established when they become equal while the decoder
is in the CD-DA mode regardless of the ENDLADR bit value.
bit 6:
DECTOUT (decoder time out)
The DECTOUT status is established when the sync mark is not detected even after the time it
takes to search 3 sectors (40.6 ms at normal speed playback) has elapsed after the decoder
has been set to the monitor-only, write-only or real-time correction mode.
bit 5:
Reserved
Normally set low.
bit 4:
RTADPEND (real time ADPCM end)
The RTADPEND status is established when real-time ADPCM decoding is completed for one
sector.
bit 3:
HDMACMP (host DMA complete)
The HDMACMP status is established when DMA is completed by HXFRC.
bit 2:
DECINT (decoder interrupt)
The DECINT status is established when the sync mark is detected or inserted while the
decoder is in the write-only, monitor-only or real-time correction mode. However, it is not
established if the sync mark interval is less than 2352 bytes while the window for its detection
is open. The status is established each time one correction is completed when the decoder is
in the repeat correction mode.
bit 1:
BFWRDY (buffer write ready)
The BFWRDY status is established when there is more than one sector available for buffer
write when the decoder is in the sound map playback mode. The status is also established
for any of the following.
(1)
The sub CPU makes the DMACTL register SMEN bit high.
(2)
When there is more than one sector of sound map data area after one sector of sound
map data is written into buffer memory from the SCSI controller (not buffable).
(3)
When there is an area for sound map data writing on the buffer memory because one
sector of sound map ADPCM decoding has been completed.
bit 0:
BFEMPT (buffer empty)
The BFEMPT status is established when there is no subsequent sector data on the buffer
memory after one sector of ADPCM decoding is completed during sound map playback.
—28—
CXD1803AQ/AR
2.1.11. CLRCTL (clear control) register
When each bit of the register is set high, the corresponding chip, status, register, interrupt status and
ADPCM playback are cleared. After clearing, the bit concerned is automatically set low. Therefore,
there is no need for the sub CPU to reset low.
bit 7:
CHPRST (chip reset)
The inside of the IC is initialized when this bit is set high. This bit is automatically set low
upon completion of the initialization.
bits 6, 5: Reserved
Normally set low.
bit 4:
RTADPCLR (real time ADPCM clear)
(1)
When this is set high for real-time ADPCM playback (when the RTADPBSY bit of the
DECSTS register is high):
• ADPCM decoding for playback is suspended. (Noise may be generated.)
• The RTADPEND interrupt status is established.
(Note) The ADPEN bit (bit 7 of the ADPMNT register) must be set low before this bit
is set high.
(2)
Setting this bit high when real-time ADPCM playback is not being performed has no
effect whatsoever.
bit 3:
SMADPCLR (sound map ADPCM clear)
(1)
When this is set high for sound map ADPCM playback (when the SMADPBSY bit of
the DECSTS register is high):
• ADPCM decoding for playback is suspended. (Noise may be generated.)
• The RTADPEND interrupt status is established.
(2)
Setting this bit high when sound map ADPCM playback is not being performed has no
effect whatsoever.
bit 2:
Reserved
Normally set low.
bit 1:
PDATA (pointer data)
The data written to this bit is written in the buffer pointer bit along with the WRDATA register
value.
bit 0:
RESYNC
The CD DSP and this IC are re-synchronized when this bit is set high. Set the bit high by the
sub CPU in the following cases:
(1)
After the DRVIF register has been set
(2)
After the DBLSPD bit (bit 1 of the CHPCTL register) has been set low.
This bit is automatically set low when the CD DSP and this IC are re-synchronized.
—29—
CXD1803AQ/AR
2.1.12. CLRINT (clear interrupt status) register
When each bit of this register is set high, the corresponding interrupt status is cleared. The bit
concerned is automatically set low after its interrupt status has been cleared. Therefore, there is no
need for the sub CPU to reset low.
bit 7:
DRVOVRN (drive overrun)
bit 6:
DECTOUT (decoder time out)
bit 5:
Reserved
Normally set low.
bit 4:
RTADPEND (real time ADPCM end)
bit 3:
HDMACMP (host DMA complete)
bit 2:
DECINT (decoder interrupt)
bit 1:
BFWRDY (buffer write ready interrupt)
bit 0:
BFEMPT (buffer write empty interrupt)
2.1.13. HXFR-L (host transfer-low)
2.1.14. HXFR-H (host transfer-high)
bit 7:
DISHXFRC (disable host transfer counter)
High: The completion of the data transfer by HXFRC is disabled for data transfer between
the SCSI controller and buffer memory.
Low: The completion of the data transfer by HXFRC is enabled for data transfer between the
SCSI controller and buffer memory.
bit 6:
Reserved
bit 5:
HADR17
HADR bit 17 (MSB)
bit 4:
HADR16
HADR bit 16
bit 3:
HXFR11
HXFR (host transfer counter) bit 11 (MSB)
bit 2:
HXFR10
HXFR bit 10
bit 1:
HXFR9
HXFR bit 9
bit 0:
HXFR8
HXFR bit 8
The HXFR (host transfer) register sets the number of data transferred between the SCSI controller and
buffer memory. The sub CPU sets this number when data is transferred between the SCSI controller
and buffer memory by setting the DISHXFRC bit low.
2.1.15. HADR-L (host address-low)
2.1.16. HADR-M (host address-middle)
The HADR (host address) register is for the head addresses of data transfer between the SCSI
controller and buffer memory. The upper two HADR bits are in HXFR-H.
—30—
CXD1803AQ/AR
2.1.17. DADRC-L
This counter keeps the address for writing the data from the drive into the buffer. When drive data is
written into the buffer, the DADRC value is output from MA0 to 17 (when SRAM is connected).
DADRC is incremented each time 1 byte of data is written from the drive into the buffer.
The sub CPU sets the head address for buffer writing into DADRC before the decoder operates in the
write-only, real-time correction or CD-DA mode.
The sub CPU can set DADRC at any time. The contents of DADRC should not be changed while the
decoder is operating in any of the above modes.
2.1.18. DADRC-M
2.1.19. DADRC-H
2.1.20. CADRC-L
This counter keeps the address for writing/reading the data from the sub CPU into the buffer. When
drive data is written into the buffer, the DADRC value is output from MA0 to 17 (when SRAM is
connected). DADRC is incremented each time 1 byte of data is written from the drive into the buffer.
The sub CPU can set CADRC at any time.
2.1.21. CADRC-M
2.1.22. CADRC-H
bit 7:
Reserved
bit 6:
CPU SRC (sub CPU source)
This bit is set high when the sub CPU writes data into the buffer. It is set low when the sub
CPU reads data from the buffer.
bit 5:
CDMAEN (sub CPU DMA enable)
This bit is set high when the sub CPU reads or writes data in the buffer memory.
bits 4 to 2:Reserved
bit 1:
CADRC bit 17 (MSB)
bit 0:
CADRC bit 16
2.1.23. DMACTL (DMA control)
bit 7:
BFRD (buffer read)
Transfer of (drive) data from the buffer memory to the SCSI controller begins when this bit
is set high. The bit is automatically set low after transfer is completed.
bit 6:
BFWR (buffer write)
Transfer of data from the SCSI controller to buffer memory begins when this bit is set high.
The bit is automatically set low after transfer is completed.
bit 5:
SMEN (sound map enable)
Set high when sound map ADPCM playback is performed.
bits 4 to 0:Reserved
The sub CPU must set these bits low.
—31—
CXD1803AQ/AR
2.1.24. SMCI
Writes the coding information bytes when sound map ADPCM playback is performed.
bit 6:
EMPHASIS
Set high when an ADPCM sector where emphasis has been applied is played back.
bit 4:
BITLNGTH (bit length)
Indicates the bit length of the coding information for ADPCM playback.
High: 8 bits
Low: 4 bits
bit 2:
FS (sampling frequency)
Indicates ADPCM playback sampling frequency.
High: 18.9 kHz
Low: 37.8 kHz
bit 0:
S/M (stereo/monaural)
Indicates the coding information stereo or monaural for ADPCM playback.
High: stereo
Low: monaural
bits 7, 5, 3, 1: Reserved
Normally set low.
2.1.25. ADPMNT
bit 7:
RTADPEN (real-time ADPCM enable)
The sub CPU sets this high to perform real-time ADPCM playback.
bits 6 to 0:The upper 7 bits (bits 16 to 10) of the sector head address are written into these bits to
perform real-time ADPCM playback. ADPMNT bit 17 is in RTCI register bit 1. Any of the
following values can be written into this register: 00, 0C, 18, 24, 30, 3C, 54HEX (when
connected to 32K-byte buffer memory).
2.1.26. RTCI
Writes the coding information bytes when real-time ADPCM playback is performed.
bit 6:
EMPHASIS
Set high when an ADPCM sector where emphasis has been applied is played back.
bit 4:
BITLNGTH (bit length)
Indicates the bit length of the coding information for ADPCM playback.
High: 8 bits
Low: 4 bits
bit 2:
FS (sampling frequency)
Indicates sampling frequency of ADPCM playback.
High: 18.9 kHz
Low: 37.8 kHz
bit 1:
ADPMNT17
ADPMNT bit 17 (MSB)
bit 0:
S/M (stereo/monaural)
Indicates the coding information stereo or monaural for ADPCM playback.
High: stereo
Low: monaural
bits 7, 5, 3: Reserved
Normally set low.
—32—
CXD1803AQ/AR
2.1.27. ATV (attenuation value) register 0
2.1.28. ATV (attenuation value) register 1
2.1.29. ATV (attenuation value) register 2
2.1.30. ATV (attenuation value) register 3
The attenuation values are set in these registers.
ATV0
ADPCM
+
L
+
R
ATV3
DF
ATV1
DECODER
ATV2
Setting 81HEX or higher in these registers is prohibited. When bits 7 to 0 of these registers are "b7" to
"b0", the attenuation (dB) is as follows:
Attenuation = 201og (b7×20+b6×2-1+b5×2-2+b4×2-3+b3×2-4+b2×2-5+b1×2-6+b0×27
The relationship expressed in the above formula and ATV register settings are given in the following
table.
—33—
CXD1803AQ/AR
Setting
80
7F
7E
7D
7C
7B
7A
79
78
77
76
75
74
73
72
71
70
6F
6E
6D
6C
6B
6A
69
68
67
66
65
64
63
62
61
60
5F
5E
5D
5C
5B
5A
59
58
57
56
Attenuation
0.00
0.07
0.14
0.21
0.28
0.35
0.42
0.49
0.56
0.63
0.71
0.78
0.86
0.93
1.01
1.08
1.16
1.24
1.32
1.40
1.48
1.56
1.64
1.72
1.80
1.89
1.97
2.06
2.14
2.23
2.32
2.41
2.50
2.59
2.68
2.77
2.87
2.96
3.06
3.16
3.25
3.35
3.45
Setting
55
54
53
52
51
50
4F
4E
4D
4C
4B
4A
49
48
47
46
45
44
43
42
41
40
3F
3E
3D
3C
3B
3A
39
38
37
36
35
34
33
32
31
30
2F
2E
2D
2C
2B
Attenuation
3.56
3.66
3.76
3.87
3.97
4.08
4.19
4.30
4.41
4.53
4.64
4.76
4.88
5.00
5.12
5.24
5.37
5.49
5.62
5.75
5.89
6.02
6.16
6.30
6.44
6.58
6.73
6.88
7.03
7.18
7.34
7.50
7.66
7.82
7.99
8.16
8.34
8.52
8.70
8.89
9.08
9.28
9.47
Setting
2A
29
28
27
26
25
24
23
22
21
20
1F
1E
1D
1C
1B
1A
19
18
17
16
15
14
13
12
11
10
0F
0E
0D
0C
0B
0A
09
08
07
06
05
04
03
02
01
00
Attenuation
9.68
9.89
10.10
10.32
10.55
10.78
11.02
11.26
11.51
11.77
12.04
12.32
12.60
12.90
13.20
13.52
13.84
14.19
14.54
14.91
15.30
15.70
16.12
16.57
17.04
17.54
18.06
18.62
19.22
19.87
20.56
21.32
22.14
23.06
24.08
25.24
26.58
28.16
30.10
32.60
36.12
42.14
∞
Relationship between ATV register settings and attenuation amounts
All written registers, except the ATV0 and ATV2 registers, are 00HEX when the IC is reset (both hard and soft
reset). The ATV0 and ATV2 registers are 80HEX when the IC is reset. "Hard reset" means that the XRST pin
is set low. "Soft reset" means that the sub CPU resets the IC.
—34—
CXD1803AQ/AR
2.2.
Read registers
In the descriptions of the ECCSTS, DECSTS, HDRFLG, HCR, SHDR and CMADR-H registers, the
current sector denotes the sector for which these registers are valid for the decoder interrupt
(DECINT). In the monitor-only or write-only mode, the sector sent from the CD DSP immediately
before the decoder interrupt is called the current sector. In the real-time correction mode and repeat
correction mode, the current sector is that in which error detection correction has been completed.
2.2.1. ECCSTS (ECC status)
bit 7:
EDCALL0 (EDC ALL 0)
This is high when there are no error flags in all the 4 EDC parity bytes of the current sector
and their values are all 00h.
bit 6:
ERINBLK (erasure in block)
(1)
When the decoder is operating in the monitor-only, write-only or real-time mode which
prohibits erasure correction, this indicates that at least a 1-byte error flag (C2PO) has
been raised in the data excluding the sync mark from the current sector CD DSP.
(2)
When the decoder is operating in the real-time correction mode which performs
erasure correction, this indicates that at least a 1-byte error flat (MDBP) has been
raised in the data excluding the sync mark from the current sector CD DSP.
bit 5:
CORINH (correction inhibit)
This is high if the current sector MODE and FORM could not be determined when the
AUTODIST bit of the DECCTL register is set high. ECC or EDC is not executed in this
sector. The CORINH bit is invalid when AUTODIST is set low. It is high in any of the
conditions below when the AUTODIST bit is set high.
(1)
When the C2 pointer of the MODE byte is high
(2)
When the MODE byte is a value other than 01HEX or 02HEX.
(3)
When the MODE byte is 02HEX and the C2 pointer is high in the submode byte
bit 4:
CORDONE (correction done)
Indicates that there is an error corrected byte in the current sector.
bit 3:
EDCOK
Indicates that an EDC check has found no errors in the current sector.
bit 2:
ECCOK
Indicates that there are no more errors from the header byte to P parity byte in the current
sector. (Bit 2 = don't care in the MODE2, FORM2 sectors.)
EDCOK
L
ECCOK
L
L
H
H
L
Description
Error(s) present in current sector
(1), (2) or (3) applies:
(1) ECD overlooked
(2) Error corrected
(3) Error(s) present in header byte with FORM2
(1) EDC overlooked,
or
H
H
(2) Error(s) present in P parity byte
No error(s) in current sector
—35—
CXD1803AQ/AR
bit 1:
bit 0:
CMODE (correction mode)
CFORM (correction form)
Indicates the MODE and FORM of the current sector whom the decoder has discriminated to
correct errors when the decoder is operating in the real-time correction or repeat correction
mode.
CFORM
'X'
'L'
'H'
CMODE
'L'
'H'
'H'
MODE1
MODE2, FORM1
MODE2, FROM2
2.2.2. DECSTS (decoder status) register
bit 1:
SHRTSCT (short sector)
Indicates that the sync mark interval was less than 2351 bytes. This sector does not remain
in the buffer memory.
bit 0:
NOSYNC
Indicates that the sync mark was inserted because one was not detected in the prescribed
position.
2.2.3. HDRFLG (header flag) register
Indicates the error flags of the header and sub header register bytes.
2.2.4. HDR (header) register
This is a 4-byte register which indicates the current sector header byte. By setting the address to
03HEX and reading out the data in sequence, the sub CPU can ascertain the values of the current
sector header bytes from the MINUTE byte.
2.2.5. SHDR (sub header) register
This is a 4-byte register which indicates the current sector sub header byte. By setting the address to
04HEX and reading out the data in sequence, the sub CPU can ascertain the values of the current
sector sub header bytes from the File byte.
The contents of the HDRFLG, HDR and SHDR registers indicate:
(1) The corrected value in the real-time correction or repeat correction mode
(2) Value of the raw data from the drive in the monitor-only or write-only mode
The CMOME and CMODE bits (bits 1, 0) of ECCSTS indicate the FORM and MODE of the sector the
decoder has discriminated by the raw data from the drive. Due to erroneous corrections, the values of
these bits may be at variance with those of the HDR register MODE byte and SHDR register submode
byte bit 5.
—36—
CXD1803AQ/AR
2.2.6. CMADR-H (current minute address high) register
Indicates the upper 8 bits of the buffer memory in which the current sector (after completion of
correction) minute byte is written. (The lower 10 bits are 00HEX.)
2.2.7. INTSTS (interrupt status) register
The value of each bit in this register indicates that of the corresponding interrupt status. These bits
are not affected by the values of the INTMSK register bits.
bit 7:
DRVOVRN (drive overrun)
bit 6:
DECTOUT (decoder time out)
bit 4:
RTADPEND (real-time ADPCM end)
bit 3:
HDMACMP (host DMA complete)
bit 2:
DECINT (decoder interrupt)
bit 1:
BFWRDY (buffer write ready)
bit 0:
BFEMPT (buffer empty)
2.2.8. RDDATA (CPU buffer read data)
The buffer data is read out from this register.
2.2.9. ADPCI (ADPCM coding information) register
bit 7:
MUTE
This is high when the DA data is muted.
bit 6:
EMPHASIS
This is high when emphasis is applied to the ADPCM data.
bit 5:
ADPBUSY
This is high for ADPCM decoding.
bit 4:
BITLNGTH (bit length)
Indicates the bit length of the coding information for ADPCM playback.
High: 8 bits
Low: 4 bits
bit 3:
SMADPBSY (sound map ADPCM busy)
This is high during sound map ADPCM playback.
bit 2:
FS (sampling frequency)
Indicates the sampling frequency of ADPCM playback.
High: 18.9 kHz
Low: 37.8 kHz
bit 1:
RTADPBSY (real-time ADPCM busy)
This is high during real-time ADPCM playback.
bit 0:
S/M (stereo/monaural)
Indicates the coding information stereo or monaural for ADPCM playback.
High: stereo
Low: monaural
2.2.10. HXFRC-L (host transfer counter-low)
—37—
CXD1803AQ/AR
2.2.11. HXFRC-H (host transfer counter-high)
The HXFRC counter indicates the number of remaining bytes in the data to be transferred between the
SCSI controller and the buffer memory. If sound map data is to be transferred before the data is
transferred (immediately after the sub CPU has set the BFRD and BFWR bits (bits 7 and 6) of the
DMACTL register high), 2304 (900HEX) is loaded into HXFRC. At any other time, the HXFR value is
loaded. HXFRC is decremented when data is read from the buffer memory (BFRD is high) or when
the IC accepts data from the SCSI controller (BFWR is high).
Therefore, the sub CPU cannot read the HXFRC value during transfer of data between the SCSI
controller and the IC. The values of HXDRC and the write register HXFR are almost always different.
2.2.12. HADRC-L (host address counter-low)
2.2.13. HADRC-M (host address counter-middle)
This counter keeps the addresses which write or read the data with the SCSI controller into/from the
buffer. If sound map data is to be transferred before the data is transferred, any of 600CHEX, 6A0CHEX
or 740CHEX (when connected to 32K-byte buffer memory) is loaded into HADRC. At any other time,
the HADR (sub CPU register) value is loaded.
When data from the SCSI controller is written into the buffer or data to the SCSI controller is read from
the buffer, the HADRC value is output from MA0 to 16. HADRC is incremented each time one byte of
data from the drive is read from the buffer (BFRD is high) or written into the buffer (BFWR is high).
Therefore, the sub CPU cannot read the HADRC value during transfer of data between the SCSI
controller and the IC. The values of HADRC and the write register HADR are almost always different.
The upper two bits of HADRC are in HXFRC-H.
2.2.14. DADRC-L
2.2.15. DADRC-M
The DADRC value is incremented before the data from the drive is written into buffer memory.
Therefore, the sub CPU can not read the DADRC value during decoder write-only or repeat correction
modes.
The upper two DADRC bits are in HXFRC-H.
2.2.16. CADRC-L
2.2.17. CADRC-M
2.2.18. CADRC-H
bit 6:
CBFRDRDY (sub CPU buffer read ready)
The sub CPU can read the RDDATA register when this bit is high.
bit 5:
CBFWRRDY (sub CPU buffer write ready)
The sub CPU can write in the WRDATA register when this bit is high.
bit 2:
CADRC17
CADRC bit 17 (MSB).
bit 1:
PDATA (pointer data)
The buffer memory pointer bit value can be read from this bit.
bit 0:
CADRC16
CADRC bit 16.
—38—
CXD1803AQ/AR
REG
ADR
SPE
CTL
MODE
SEL
bit4
BCK
MD1
RAM
SZ1
SPMJ
CTL
FROM
SEL
bit3
BCK
MD0
RAM
SZ0
SM
BF2
AUTO
DIST
bit2
LSB
1st
9bit
RAM
DAMIX
DIS
DEC
MD2
DRVIF
00
bit6
bit5
bit4
bit3
bit15
bit14
bit13
bit12
06
'L'
'L'
'L'
CHPCTL
07
SM
MUTE
RT
MUTE
WRDATA
08
bit7
INTMSK
09
CLRCTL
0A
CLRINT
0B
CONFIG
1
CONFIG
2
DECCTL
DLADR
-L
DLADR
-M
DLADR
-H
HXFR
-L
HXFR
-H
HADR
-L
HADR
-M
DADRC
-L
DADRC
-M
DADRC
-H
bit7
C2PO
L1st
bit6
LCH
LOW
bit5
BCK
RED
bit1
bit0
'L'
'L'
'L'
XSLOW
'L'
CLK
DIS
DACOUT
EN
DEC
MD1
HCLK
DIS
PRTY
CTL
DEC
MD0
SCYC
1
EN
DLADR
SCYC
0
ECC
STR
04
bit7
bit2
bit1
bit0
05
bit11
bit10
bit9
bit8
'L'
'L'
'L'
bit17
bit16
CDDA
MUTE
CDDA
SW
OPEN
RPS
TART
DBL
SPD
'L'
bit6
bit5
bit4
bit3
bit2
bit1
bit0
DRV
OVRN
CHP
RST
DRV
OVRN
DEC
TOUT
'L'
'L'
DEC
TOUT
'L'
HDMA
CMP
SMADP
CLR
HDMA
CMP
DEC
INT
'L'
RTADP
END
RTADP
CLR
RTADP
END
DEC
INT
BF
WRDY
P
DATA
BF
WRDY
BF
EMPT
RE
SYNC
BF
EMPT
0C
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
0D
DIS
HXFRC
'L'
HADR
bit17
HADR
bit16
bit11
bit10
bit9
bit8
0E
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
0F
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
10
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
11
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
12
'L'
'L'
'L'
'L'
'L'
'L'
bit17
bit16
13
|
14
'L'
'L'
'L'
'L'
'L'
'L'
'L'
'L'
01
02
03
Sub CPU write registers (1)
—39—
'L'
CXD1803AQ/AR
REG
CADRC
-L
CADRC
-M
CADRC
-H
ADR
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
15
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
16
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
17
'L'
CPU
SRC
CDMA
EN
'L'
'L'
'L'
bir17
bit16
DMACTL
18
BFRD
BFWR
SMEN
'L'
'L'
'L'
'L'
'L'
ADPMNT
19
RTADP
EN
bit16
bit15
bit14
bit13
bit12
bit11
bit10
SMCI
1A
'L'
'L'
FS
'L'
S/M
RTCI
1B
'L'
'L'
FS
ADPMNT
bit17
S/M
ATV0
1C
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
ATV1
1D
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
ATV2
1E
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
ATV3
1F
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
EMPH
ASIS
EMPH
ASIS
'L'
'L'
BIT
LNGTH
BIT
LNGTH
Sub CPU write registers (2)
—40—
CXD1803AQ/AR
REG
ADR
bit7
EDC
ALL0
bit6
ERIN
BLK
bit5
COR
INH
bit4
COR
DONE
bit3
EDC
OK
bit2
ECC
OK
ECCSTS
00
DECSTS
01
—
—
—
—
—
—
HDRFLG
02
MIN
SEC
BLO
CK
MODE
FILE
HDR
03
bit7
bit6
bit5
bit4
SHDR
04
bit7
bit6
bit5
CMADR
-H
05
bit17
bit16
INTSTS
07
DRV
OVRN
RDDATA
08
ADPCI
HXFRC
-L
HXFRC
-H
HADRC
-L
HADRC
-M
DADRC
-L
DADRC
-M
CADRC
-L
CADRC
-M
CADRC
-H
bit0
C
FORM
NO
SYNC
CHAN
NEL
bit1
C
MODE
SHRT
SCT
SUB
MODE
bit3
bit2
bit1
bit0
bit4
bit3
bit2
bit1
bit0
bit15
bit14
bit13
bit12
bit11
bit10
DEC
TOUT
—
RTADP
END
HDMA
CMP
DEC
INT
BF
WRDY
BF
EMPT
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
09
MUTE
EMPH
ASIS
ADP
BSY
BIT
LNGTH
SMADP
BSY
FS
RTADP
BSY
S/M
0A
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
0B
DC
bit17
HC
bit17
DC
bit16
HC
bit16
bit11
bit10
bit9
bit8
0C
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
0D
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
0E
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
0F
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
10
|
1C
—
—
—
—
—
—
—
—
1D
bit7
bit6
bit5
bit4
bit3
bit2
bit1
bit0
1E
bit15
bit14
bit13
bit12
bit11
bit10
bit9
bit8
CBF
RDRDY
CBF
WRDRY
—
—
bit17
P
DATA
bit16
1F
Sub CPU read registers
For HXFRC-H, DC and HC represent DADRC and HASRC respectively.
—41—
CI
CXD1803AQ/AR
3. Connection with Buffer Memory
3.1.Memory types
The DRAM pin input, CNFIG1 register RAMSZ1, RAMSZ0 and 9BITRAM bits (bits 4 to 2) are set
depending on the buffer memory connected to the IC.
DRAM
'L'
'L'
'L'
'L'
'L'
'L'
'L'
'L'
'H'
RAMSZ1
'L'
'L'
'L'
'L'
'H'
'H'
'H'
'H'
'H'
RAMSZ0
'L'
'L'
'H'
'H'
'L'
'L'
'H'
'H'
'H'
9BITRAM
'L'
'H'
'L'
'H'
'L'
'H'
'L'
'H'
'L'
Memory size
32K ×8bSRAM
32KW×9bSRAM
32KW×8bSRAM×2
32KW×9bSRAM×2
128KW×8bSRAM
128KW×9bSRAM
128KW×8bSRAM×2
128KW×9bSRAM×2
256KW×4bDRAM×2
W
Figs. 3-1 to 3.5 show examples of connection.
3.2.Access time
The relationship between the decoder clock frequency (MHz) and minimum access time required by the
memory (preliminary value, ns) when the CONFIG1 register XSLOW is high is shown below.
Clock frequency
16.9344
20.0000
24.0000
32.0000
33.8688
Access time
SRAM
DRAM
120
110
100
90
70
80
50
50
45
50
When XSLOW is low and clock frequency is 16.9344 MHz, SRAM access time is 500 ns and DRAM
access time is 300 ns.
—42—
—43—
XMWR
MA15
/WR
/CE
XMWR
XME0
∗1 Connect to 9 bits / word SRAM when performing erasure correction.
∗2 Connect /CE to XME0 or ground.
Fig. 3-1 Connection to 32K-byte SRAM
∗1
/CE
/WR
/OE
I/O9
I/O8 to 1
A14 to 0
32KB SRAM
/CE
/WR
/OE
I/O9
I/O8 to 1
A14 to 0
32KB SRAM
Fig. 3-2 Connection to 64K-byte SRAM
XMOE
/OE
XMOE
∗2
MDBP
MDBP
I/O9
MDB7 to 0
I/O8 to 1
MDB7 to 0
∗1
MA14 to 0
CXD1803AQ/AR
A14 to 0
32KB SRAM
MA14 to 0
CXD1803AQ/AR
CXD1803AQ/AR
∗1
/WR
/CE1
XMWR
XME0
—44—
∗1 Connect to x9 SRAM when performing erasure correction.
∗2 Connect /CE1 to XME0 or ground.
∗3 Connect CE2 to VDD.
Fig. 3-3 Connection to 128K-byte SRAM
∗2
/OE
XMOE
I/O9
I/O8 to 1
MDB7 to 0
MDBP
A16 to 0
128KB SRAM
MA16 to 0
CXD1803AQ/AR
∗1
/CE1
/WR
/OE
I/O9
I/O8 to 1
A14 to 0
128KB SRAM
/CE1
/WR
/OE
I/O9
I/O8 to 1
A14 to 0
128KB SRAM
Fig. 3-4 Connection to 256K-byte SRAM
XME1
XME0
XMWR
XMOE
MDBP
MDB7 to 0
MA14 to 0
CXD1803AQ/AR
CXD1803AQ/AR
I/O4 to 1
MDB7 to 4
/CAS
/WE
XCAS
XMWR
—45—
∗4 Connect DRAM /OE pin to ground.
Fig. 3-5 Connection to 256K-byte DRAM
/WE
/CAS
/RAS
I/O4 to 1
A8 to 0
128KB DRAM
/RAS
XRAS
MDB3 to 0
A8 to 0
128KB DRAM
MA8 to 0
CXD1803AQ/AR
CXD1803AQ/AR
CXD1803AQ/AR
Unit : mm
CXD1803AQ
100PIN QFP (PLASTIC)
+ 0.1
0.15 – 0.05
+ 0.4
14.0 – 0.01
17.9 ± 0.4
23.9 ± 0.4
+ 0.4
20.0 – 0.1
15.8 ± 0.4
Package Outline
A
0.65
+ 0.35
2.75 – 0.15
±0.12 M
0° to 15°
DETAIL A
0.8 ± 0.2
(16.3)
0.15
PACKAGE STRUCTURE
PACKAGE MATERIAL
EPOXY RESIN
SOLDER PLATING
SONY CODE
QFP-100P-L01
LEAD TREATMENT
EIAJ CODE
∗QFP100-P-1420-A
LEAD MATERIAL
COPPER / 42 ALLOY
PACKAGE WEIGHT
1.4g
JEDEC CODE
100PIN LQFP (PLASTIC)
CXD1803AR
16.0 ± 0.2
∗
14.0 ± 0.1
75
51
76
(15.0)
50
0.5 ± 0.2
A
26 (0.22)
100
1
0.5 ± 0.08
+ 0.08
0.18 – 0.03
25
+ 0.2
1.5 – 0.1
+ 0.05
0.127 – 0.02
0.1
0° to 10°
0.5 ± 0.2
0.1 ± 0.1
DETAIL A
NOTE: Dimension “∗” does not include mold protrusion.
PACKAGE STRUCTURE
PACKAGE MATERIAL
EPOXY/PHENOL RESIN
SONY CODE
LQFP-100P-L01
LEAD TREATMENT
SOLDER PLATING
EIAJ CODE
∗QFP100-P-1414-A
LEAD MATERIAL
42 ALLOY
JEDEC CODE
PACKAGE WEIGHT
—46—