STMICROELECTRONICS ESDALC6V1-1U2

ESDALC6V1-1U2
Single-line low capacitance Transil™ for ESD protection
Features
■
Breakdown voltage VBR = 6.1 V min.
■
Unidirectional device
■
Multiple ESD strike sustainability
■
Very low diode capacitance: 12 pF typ. at 0 V
■
Low leakage current
■
0201 SMD package size compatible
■
Ultra small PCB area: 0.18 mm2
■
RoHS compliant
Pin 1 available in different forms
ST0201 package
Benefits
■
High ESD protection level
■
High integration
■
Suitable for high density boards
■
MSL1
Figure 1.
Functional diagram (top view)
Complies with the following standards:
■
IEC 61000-4-2 level 4
Applications
Where transient overvoltage protection in ESD
sensitive equipment is required, such as:
■
Portable multimedia players and accessories
■
Notebooks
■
Digital cameras and camcorders
■
Communication systems
■
Cellular phone handsets and accessories
Description
The ESDALC6V1-1U2 is a unidirectional single
line TVS diode designed to protect the data lines
or other I/O ports against ESD transients.
The device is ideal for applications where both
reduced line capacitance and board space saving
are required.
TM: Transil is a trademark of STMicroelectronics
September 2011
Doc ID 15089 Rev 3
1/11
www.st.com
11
Characteristics
ESDALC6V1-1U2
1
Characteristics
Table 1.
Absolute maximum ratings (Tamb = 25 °C)
Symbol
Parameter
VPP
Peak pulse voltage:
IEC 61000-4-2 contact discharge
PPP
Peak pulse power dissipation (8/20 µs) (1)
IPP
Peak pulse current (8/20 µs)
Tj
Junction temperature
Tstg
Value
Unit
kV
±8
Tj initial = Tamb
Storage temperature range
TL
Maximum lead temperature for soldering during 10 s
Top
Operating junction temperature range
20
W
2
A
125
°C
- 55 to +150
°C
260
°C
-40 to +125
°C
1. For a surge greater than the maximum values, the diode will fail in short-circuit
Figure 2.
Electrical characteristics (definitions)
I
Symbol
VBR
VCL
IRM
VRM
IF
IPP
IR
VF
Rd
αT
Table 2.
=
=
=
=
=
=
=
=
=
=
IF
VF
VCL VBR VRM
V
IRM
IR
Slope = 1/Rd
IPP
Electrical characteristics (values, Tamb = 25 °C)
Symbol
2/11
Parameter
Breakdown voltage
Clamping voltage
Leakage current @ VRM
Stand-off voltage
Forward current
Peak pulse current
Breakdown current
Forward voltage drop
Dynamic impedance
Voltage temperature
Test conditions
Min.
VBR
IR = 1 mA
IRM
VRM = 3 V
Rd
Square pulse, IPP = 1 A tp = 2.5 µs
αT
ΔVBR = αT(Tamb - 25 °C) x VBR (25 °C)
Cline
VR = 0 V, Fosc = 1 MHz, Vosc = 30 mV
Typ.
6.1
Doc ID 15089 Rev 3
Max.
Unit
8.0
V
100
nA
4.5
-4
Ω
1.3
12.0
10 /°C
pF
ESDALC6V1-1U2
Figure 3.
Characteristics
Relative variation of peak pulse
power versus initial junction
temperature
Figure 4.
Peak pulse power versus
exponential pulse duration
PPP(W)
PPP[T j initial] / PPP [T j initial=25°C]
1000
1.1
Tj initial = 25 °C
1.0
0.9
0.8
100
0.7
0.6
0.5
0.4
10
0.3
0.2
T j(°C)
0.1
tP(µs)
0.0
1
0
25
Figure 5.
50
75
100
125
150
Clamping voltage versus peak
pulse current
(square pulse, typical values)
1
Figure 6.
IPP(A)
10.0
10
1000
Junction capacitance versus
reverse applied voltage
(typical values)
C(pF)
12
Tp = 2.5 µs
Tj initial =25 °C
100
F=1 MHz
VOSC=30 mVRMS
Tj=25 °C
10
8
6
1.0
4
2
VCL(V)
Vline (V)
0
0.1
5
Figure 7.
7
9
11
13
0
15
1
2
3
4
5
Relative variation of leakage current versus junction temperature (typical values)
IR [T j] / IR [T j=25°C]
100
VR =3V
10
T j(°C)
1
25
50
75
Doc ID 15089 Rev 3
100
125
3/11
Characteristics
Figure 8.
ESDALC6V1-1U2
ESD response to IEC 61000-4-2
(+8 kV contact discharge)
Figure 9.
ESD response to IEC 61000-4-2
(-8 kV contact discharge)
10 V/Div
10 V/Div
20 ns/Div
20 ns/Div
Figure 10. S21 attenuation measurement results
0.00
dB
- 6.00
Average
Performance
(50WSystem)
(50Ω System)
-12.00
-18.00
Pass band
attenuation
0.01 dB
-3 dB point
1.02MHz
538
GHz
Attenuation
(0.8 – 4GHz)
< -5.2
-2.1dB
dB
(-6.1dB@900 MHz
(-2.5dB@900MHz
[email protected])
-14
[email protected] GHz)
-24.00
F (Hz)
- 30.00
100.0k
4/11
1.0M
10.0M
Doc ID 15089 Rev 3
100.0M
1.0G
ESDALC6V1-1U2
2
Ordering information scheme
Ordering information scheme
Figure 11. Ordering information scheme
ESDA LC 6V1 - 1U2
ESD Array
Low capacitance
Breakdown Voltage
6V1 = 6.1 V min
Package
U2 = ST0201
Doc ID 15089 Rev 3
5/11
Package information
3
ESDALC6V1-1U2
Package information
●
Epoxy meets UL94, V0
●
Lead-free packages
In order to meet environmental requirements, ST offers these devices in different grades of
ECOPACK® packages, depending on their level of environmental compliance. ECOPACK®
specifications, grade definitions and product status are available at: www.st.com.
ECOPACK® is an ST trademark.
Table 3.
ST0201 dimensions
Dimensions
D
Ref
Millimetres
Inches
E
Min
Typ
Max
A
0.23
0.28
0.33 0.009 0.011 0.013
b1
0.13
0.18
0.23 0.005 0.007 0.009
b2
0.14
0.19
0.24 0.006 0.007 0.009
D
0.55
0.60
0.65 0.022 0.024 0.026
E
0.25
0.30
0.35 0.010 0.012 0.014
Top
A
Side
b1
b2
L1
Min
Typ
Max
L2
Bottom
Pin 1
b1
e
b2
L1
e
L2
Bottom
e
Pin 1 available in different forms
0.35
0.014
L1
0.20
0.25
0.30 0.008 0.010 0.012
L2
0.20
0.25
0.30 0.008 0.010 0.012
Figure 12. Footprint (dimensions in mm) Figure 13. Marking
1.05
0.425
0.425
0.30
Pin1
L1
Pin 2
0.20
Note:
6/11
Product marking may be rotated by multiples of 90° for assembly plant differentiation. In no
case should this product marking be used to orient the component for its placement on a
PCB. Only pin 1 mark is to be used for this purpose.
Doc ID 15089 Rev 3
ESDALC6V1-1U2
Package information
Figure 14. Tape and reel specifications
Bar indicates Pin 1
Ø 1.55
4.0
2.0
D1
D1
D1
0.38
0.34
D1
D1
D1
D1
8.0
0.68
3.5
1.75
0.22
2.0
All dimensions are typical values in mm
User direction of unreeling
Doc ID 15089 Rev 3
7/11
Recommendation on PCB assembly
ESDALC6V1-1U2
4
Recommendation on PCB assembly
4.1
Stencil opening design
Figure 15. Recommended stencil windows position (dimensions in mm)
1.05
0.425
0.425
0.225
0.30
0.038
0.040
0.065
0.20
Footprint
4.2
8/11
0.320
0.038
Stencil window
Solder paste
1.
Halide-free flux qualification ROL0 according to ANSI/J-STD-004.
2.
“No clean” solder paste is recommended.
3.
Offers a high tack force to resist component movement during high speed
4.
Solder paste with fine particles: powder particle size is 20-45 µm.
Doc ID 15089 Rev 3
ESDALC6V1-1U2
4.3
4.4
4.5
Recommendation on PCB assembly
Placement
1.
Manual positioning is not recommended.
2.
It is recommended to use the lead recognition capabilities of the placement system, not
the outline centering
3.
Standard tolerance of ± 0.05 mm is recommended.
4.
3.5 N placement force is recommended. Too much placement force can lead to
squeezed out solder paste and cause solder joints to short. Too low placement force
can lead to insufficient contact between package and solder paste that could cause
open solder joints or badly centered packages.
5.
To improve the package placement accuracy, a bottom side optical control should be
performed with a high resolution tool.
6.
For assembly, a perfect supporting of the PCB (all the more on flexible PCB) is
recommended during solder paste printing, pick and place and reflow soldering by
using optimized tools.
PCB design preference
1.
To control the solder paste amount, the closed via is recommended instead of open
vias.
2.
The position of tracks and open vias in the solder area should be well balanced. The
symmetrical layout is recommended, in case any tilt phenomena caused by
asymmetrical solder paste amount due to the solder flow away.
Reflow profile
Figure 16. ST ECOPACK® recommended soldering reflow profile for PCB mounting
Temperature (°C)
260°C max
255°C
220°C
180°C
125 °C
2°C/s recommended
2°C/s recommended
6°C/s max
6°C/s max
3°C/s max
3°C/s max
0
0
1
2
3
4
5
10-30 sec
90 to 150 sec
Note:
6
7
Time (min)
90 sec max
Minimize air convection currents in the reflow oven to avoid component movement.
Doc ID 15089 Rev 3
9/11
Ordering information
5
ESDALC6V1-1U2
Ordering information
Table 4.
Ordering information
Order code
Marking
Weight
Base qty
Delivery mode
ESDALC6V1-1U2
L1(1)
0.124 mg
15000
Tape and reel
1. The marking can be rotated by multiples of 90° to differentiate assembly location
6
Revision history
Table 5.
10/11
Document revision history
Date
Revision
Changes
07-Oct-2008
1
Initial release.
25-Jan-2010
2
Updated base qty Table 4.
22-Sep-2011
3
Updated package illustrations on page 1 and in Table 3 for Pin 1
available forms.
Doc ID 15089 Rev 3
ESDALC6V1-1U2
Please Read Carefully:
Information in this document is provided solely in connection with ST products. STMicroelectronics NV and its subsidiaries (“ST”) reserve the
right to make changes, corrections, modifications or improvements, to this document, and the products and services described herein at any
time, without notice.
All ST products are sold pursuant to ST’s terms and conditions of sale.
Purchasers are solely responsible for the choice, selection and use of the ST products and services described herein, and ST assumes no
liability whatsoever relating to the choice, selection or use of the ST products and services described herein.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted under this document. If any part of this
document refers to any third party products or services it shall not be deemed a license grant by ST for the use of such third party products
or services, or any intellectual property contained therein or considered as a warranty covering the use in any manner whatsoever of such
third party products or services or any intellectual property contained therein.
UNLESS OTHERWISE SET FORTH IN ST’S TERMS AND CONDITIONS OF SALE ST DISCLAIMS ANY EXPRESS OR IMPLIED
WARRANTY WITH RESPECT TO THE USE AND/OR SALE OF ST PRODUCTS INCLUDING WITHOUT LIMITATION IMPLIED
WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE (AND THEIR EQUIVALENTS UNDER THE LAWS
OF ANY JURISDICTION), OR INFRINGEMENT OF ANY PATENT, COPYRIGHT OR OTHER INTELLECTUAL PROPERTY RIGHT.
UNLESS EXPRESSLY APPROVED IN WRITING BY TWO AUTHORIZED ST REPRESENTATIVES, ST PRODUCTS ARE NOT
RECOMMENDED, AUTHORIZED OR WARRANTED FOR USE IN MILITARY, AIR CRAFT, SPACE, LIFE SAVING, OR LIFE SUSTAINING
APPLICATIONS, NOR IN PRODUCTS OR SYSTEMS WHERE FAILURE OR MALFUNCTION MAY RESULT IN PERSONAL INJURY,
DEATH, OR SEVERE PROPERTY OR ENVIRONMENTAL DAMAGE. ST PRODUCTS WHICH ARE NOT SPECIFIED AS "AUTOMOTIVE
GRADE" MAY ONLY BE USED IN AUTOMOTIVE APPLICATIONS AT USER’S OWN RISK.
Resale of ST products with provisions different from the statements and/or technical features set forth in this document shall immediately void
any warranty granted by ST for the ST product or service described herein and shall not create or extend in any manner whatsoever, any
liability of ST.
ST and the ST logo are trademarks or registered trademarks of ST in various countries.
Information in this document supersedes and replaces all information previously supplied.
The ST logo is a registered trademark of STMicroelectronics. All other names are the property of their respective owners.
© 2011 STMicroelectronics - All rights reserved
STMicroelectronics group of companies
Australia - Belgium - Brazil - Canada - China - Czech Republic - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan Malaysia - Malta - Morocco - Philippines - Singapore - Spain - Sweden - Switzerland - United Kingdom - United States of America
www.st.com
Doc ID 15089 Rev 3
11/11