HOLTEK HT95L100-64QFP-A

HT95L100/10P
Preliminary
8-Bit LCD Type Phone Controller MCU
Features
· Provide MASK type and OTP type version
· Up to 1.117ms instruction cycle with 3.58MHz system
· Operating voltage range: 2.4V~5.5V
clock
· Program ROM: 4K´16 bits
· Built-in 3.58MHz DTMF Generator
· Data RAM: 1152´8 bits
· LCD driver:
- 20 seg.´8 com.
- 4 segments can per nibble option to bidirectional
· Up to 20 bidirectional I/O lines
· 16-bit table read instructions
I/O lines
· Eight-level subroutine nesting
- LCD contrast can be adjusted by software or exter-
· Timer:
nal resistor
- Two 16-bit programmable Timer/Event Counter
- Real time clock (RTC)
- Watchdog Timer (WDT)
- Fixed frame frequency 64Hz
· Built-in Low Battery detector
· All instructions in one or two machine cycles
· Programmable frequency divider (PFD)
· Built-in dialer I/O
· Dual system clock: 32768Hz, 3.58MHz
· 64-pin QFP package
· Four operating modes: Idle mode, Sleep mode,
Green mode and Normal mode
Applications
· Deluxe Feature Phone
· Fax and answering machines
· Caller ID Phone
· Other communication system
· Cordless Phone
General Description
can also operate with high speed system clock rate of
3.58MHz in normal mode for high performance operation. To ensure smooth dialer function and to avoid MCU
shut-down in extreme low voltage situation, the dialer
I/O circuit is built-in to generate hardware dialer signals
such as on-hook, hold-line and hand-free. Built-in real
time clock and programmable frequency divider are provided for additional fancy features in product developments. The device is best suitable for feature phone
products that comply with versatile dialer specification
requirements of different areas or countries.
The HT95L100/10P are 8-bit high performance
RISC-like microcontrollers with built-in DTMF generator
and dialer I/O which provide MCU dialer implementation
or system control features for telecom product application. The phone controller has a built-in program ROM,
data RAM, LCD driver and a maximum of 20 I/O lines for
high end products design. In addition, for power management purpose, it has a built-in frequency up conversion circuit (32768Hz to 3.58MHz) which provides dual
system clock and four types of operation modes. For example it can operate with low speed system clock rate of
32768Hz in green mode with little power consumption. It
Rev. 0.10
1
October 1, 2002
Preliminary
HT95L100/10P
Selection Table
Part No.
Operating Program
Data
Normal Dialer
Voltage
Memory Memory
I/O
I/O
LCD
Timer
Stack
External
Interrupt
DTMF
Generator
FSK
Receiver
Package
HT95A200
HT95A20P
2.4V~5.5V
4K´16
1152´8
28
8
¾
16-bit´2
8
4
Ö
¾
48SSOP
HT95A300
HT95A30P
2.4V~5.5V
8K´16
2112´8
28
8
¾
16-bit´2
8
4
Ö
¾
48SSOP
HT95L100
HT95L10P
2.4V~5.5V
4K´16
1152´8
16~20
8
16´8~20´8
16-bit´2
8
4
Ö
¾
64QFP
HT95L200
HT95L20P
2.4V~5.5V
8K´16
1152´8
20~28
8
24´8~24´16
16-bit´2
8
4
Ö
¾
100QFP
HT95L300
HT95L30P
2.4V~5.5V
8K´16
2112´8
16~28
8
36´16~48´16
16-bit´2
8
4
Ö
¾
100QFP
HT95C200
HT95C20P
2.4V~5.5V
8K´16
1152´8
20~28
8
24´8~24´16
16-bit´2
8
4
Ö
Ö
128QFP
HT95C300
HT95C30P
2.4V~5.5V
8K´16
2112´8
16~28
8
36´16~48´16
16-bit´2
8
4
Ö
Ö
128QFP
Note: Part numbers suffixed with ²P² are OTP devices, all others are mask version devices.
Block Diagram
R E S
P o w e r D o w n
D e te c to r &
R e s e t C ir c u it
P ro g ra m
C o u n te r
P ro g ra m
R O M
S T
S T
S T
S T
S T
S T
S T
S T
A C
A C
A C
A C
A C
A C
A C
A C
K 0
K 1
K 2
K 3
K 4
K 5
K 6
K 7
3 2 7 6 8 H z
R T C
M P 0
M P 1
M
U
A L U
H F I
H F O
H D I
H D O
H K S
P O
D N P O
X M U T E
V D D
V S S
O S C
C ir c u it
A C C
3 2 7 6 8 H z
M
T M R 0
U
X
S y s te m
c lo c k /4
P A
P A C
P A 0 ~ P A 7
S T A T U S
P B
P B C
P B 0 ~ P B 7
P E
P E C
P E 0 ~ P E 3
S h ifte r
3 2 7 6 8 H z
W D T O S C
S y s te m C lo c k /4
M
W D T S
U
X
W D T P r e s c a le r
D T M F
G e n e ra to r
D T M F
3 .5 8 M H z
D ia le r I/O
3 2 7 6 8 H z
o r 3 .5 8 M H z /4
P o w e r
S u p p ly
P F D
L o w
B a tte ry
D e te c to r
L B IN
Rev. 0.10
X
M U X
In s tr u c tio n
D e c o d e r
X 1
X 2
X C
U
IN T C 0
IN T C 1
D A T A
M e m o ry
X
IN T /T M R 1
M
T M R 1
T M R 1 C
T M R 0
T M R 0 C
In s tr u c tio n
R e g is te r
T im in g
G e n e ra to r
In te rru p t
C ir c u it
M U S IC
L C D D r iv e r
2 0 (1 6 )´ 8
C O M 0 ~ C O M 7
S E G 0 ~ S E G 1 9
2
V L C D
October 1, 2002
Preliminary
HT95L100/10P
Pin Assignment
S E G 5
S E G 4
S E G 3
S E G 2
S E G 1
S E G 0
C O M 7
C O M 6
C O M 5
C O M 4
C O M 3
C O M 2
C O M 1
6 4 6 3 6 2 6 1 6 0 5 9 5 8 5 7 5 6 5 5 5 4 5 3 5 2
C O M 0
1
5 1
S E G 6
P A 7
2
5 0
S E G 7
P A 6
3
4 9
S E G 8
P A 5
4
4 8
S E G 9
P A 4
5
4 7
S E G 1 0
P A 3
6
4 6
S E G 1 1
P A 2
7
4 5
S E G 1 2
P A 1
8
4 4
S E G 1 3
P A 0
9
4 3
S E G 1 4
P B 7
1 0
4 2
S E G 1 5
P B 6
1 1
4 1
S E G 1 6 /P E 0
P B 5
1 2
4 0
S E G 1 7 /P E 1
P B 4
1 3
3 9
S E G 1 8 /P E 2
P B 3
1 4
3 8
S E G 1 9 /P E 3
P B 2
1 5
3 7
V L C D
P B 1
1 6
3 6
M U S IC
P B 0
1 7
3 5
R E S
X M U T E
1 8
3 4
T M R 0
D N P O
1 9
3 3
D T M F
H T 9 5 L 1 0 0 /1 0 P
6 4 Q F P -A
2 0 2 1 2 2 2 3 2 4 2 5 2 6 2 7 2 8 2 9 3 0 3 1 3 2
X C
L B IN
X 2
X 1
IN T /T M R 1
V D D
V S S
H F I
H F O
H D I
H D O
H K S
P O
Pin Description
Pin Name
I/O
Description
CPU
VDD
¾
Positive power supply
VSS
¾
Negative power supply, ground
X1
I
A 32768Hz crystal (or resonator) should be connected to this pin and X2.
X2
O
A 32768Hz crystal (or resonator) should be connected to this pin and X1.
XC
I
External low pass filter used for frequency up conversion circuit.
RES
I
Schmitt trigger reset input, active low.
INT/TMR1
I
Schmitt trigger input for external interrupt or Timer/Event Counter 1.
No internal pull-high resistor.
For INT: Edge trigger activated on a falling edge.
For TMR1: Activated on falling or rising transition edge, selected by software.
TMR0
I
Schmitt trigger input for Timer/Event Counter 0.
No internal pull-high resistor.
Activated on falling or rising transition edge, selected by software.
SEG0~SEG15
O
LCD panel segment outputs.
SEG16~SEG19
(PE0~PE3)
O
or
I/O
LCD panel segment outputs.
SEG16~SEG19 can be nibble optioned to PE0~PE3 by software.
COM0~COM7
O
LCD panel common outputs.
VLCD
I
LCD driver power source.
LCD Driver
Rev. 0.10
3
October 1, 2002
Preliminary
Pin Name
I/O
HT95L100/10P
Description
Normal I/O
PA0~PA7
I/O
Bidirectional 8-bit input/output ports.
Schmitt trigger input or CMOS output.
See mask option table for pull-high and wake-up function
PB0~PB7
I/O
Bidirectional 8-bit input/output ports.
Schmitt trigger input or CMOS output.
See mask option table for pull-high function
PE0~PE3
O
or
I/O
Bidirectional 4-bit input/output ports.
Schmitt trigger input and CMOS output.
PE0~PE3 can be per nibble optioned to SEG16~SEG19 by software.
See mask option table for pull-high function
Dialer I/O (See the ²Dialer I/O function²)
HFI
I
Schmitt trigger input structure. An external RC network is recommended for input
debouncing.
This pin is pulled low with internal resistance of 200kW typ.
HFO
O
CMOS output structure.
HDI
I
Schmitt trigger input structure. An external RC network is recommended for input
debouncing.
This pin is pulled high with internal resistance of 200kW typ.
HDO
O
CMOS output structure.
HKS
I
This pin detects the status of the hook-switch and its combination with HFI/HDI can
control the PO pin output to make or break the line.
PO
O
CMOS output structure controlled by HKS and HFI/HDI pins and which determines
whether the dialer connects or disconnects the telephone line.
DNPO
O
NMOS output structure.
O
NMOS output structure. Usually, XMUTE is used to mute the speech circuit when
transmitting the dialer signal.
DTMF
O
This pin outputs dual tone signals to dial out the phone number. The load resistor should
not be less than 5kW.
MUSIC
O
This pin outputs the single tone that generated by the PFD generator.
LBIN
I
This pin detects battery low through external R1/R2 to determine threshold voltage.
XMUTE
Peripherals
Absolute Maximum Ratings
Supply Voltage ........................................-0.3V to 5.5V
Storage Temperature ...........................-50°C to 125°C
Input Voltage .............................. VSS-0.3 to VDD+0.3V
Operating Temperature ..........................-25°C to 70°C
Note: These are stress ratings only. Stresses exceeding the range specified under ²Absolute Maximum Ratings² may
cause substantial damage to the device. Functional operation of this device at other conditions beyond those
listed in the specification is not implied and prolonged exposure to extreme conditions may affect device reliability.
Rev. 0.10
4
October 1, 2002
Preliminary
HT95L100/10P
Electrical Characteristics
Symbol
Parameter
Ta=25°C
Test Conditions
VDD
Conditions
Min.
Typ.
Max.
Unit
CPU
IIDL
Idle Mode Current
5V
32768Hz off, 3.58MHz off,
CPU off, LCD off, WDT off,
no load
¾
¾
2
mA
ISLP
Sleep Mode Current
5V
32768Hz on, 3.58MHz off,
CPU off, LCD off, WDT off,
no load
¾
¾
30
mA
IGRN
Green Mode Current
5V
32768Hz on, 3.58MHz off,
CPU on, LCD off, WDT off,
no load
¾
¾
50
mA
INOR
Normal Mode Current
5V
32768Hz on, 3.58MHz on,
CPU on, LCD on, WDT on,
DTMF generator off, no load
¾
¾
3
mA
VIL
I/O Port Input Low Voltage
5V
¾
0
¾
1
V
VIH
I/O Port Input High Voltage
5V
¾
4
¾
5
V
IOL
I/O Port Sink Current
5V
¾
4
6
¾
mA
IOH
I/O Port Source Current
5V
¾
-2
-3
¾
mA
RPH
Pull-high Resistor
5V
¾
10
30
¾
kW
LBIN
Low Battery Detection
Reference Voltage
5V
¾
1.10
1.15
1.20
V
¾
¾
3
5
V
¾
¾
100
mA
¾
¾
1
mA
LCD Driver
VLCD
LCD Panel Power Supply
¾
ILCD
LCD Operation Current
¾
VLCD=5V, 32768Hz, no load
Dialer I/O
IXMO
XMUTE Leakage Current
IOLXM
XMUTE Sink Current
2.5V XMUTE pin=0.5V
1
¾
¾
mA
IHKS
HKS Input Current
2.5V HKS pin=2.5V
¾
¾
0.1
mA
RHFI
HFI Pull-low Resistance
2.5V VHFI=2.5V
¾
200
¾
kW
RHDI
HDI Pull-high Resistance
2.5V VHDI=0V
¾
200
¾
kW
IOH2
HFO Source Current
2.5V VOH=2V
-1
¾
¾
mA
IOL2
¾
¾
mA
2.5V XMUTE pin=2.5V
HFO Sink Current
2.5V VOL=0.5V
1
IOH3
HDO Source Current
2.5V VOH=2V
-1
¾
¾
mA
IOL3
HDO Sink Current
2.5V VOL=0.5V
1
¾
¾
mA
IOH4
PO Source Current
2.5V VOH=2V
-1
¾
¾
mA
IOL4
PO Sink Current
2.5V VOL=0.5V
1
¾
¾
mA
IOL5
DNPO Sink Current
2.5V VOL=0.5V
1
¾
¾
mA
0.45VDD
¾
0.7VDD
V
DTMF Generator
VTDC
DTMF Output DC Level
¾
VDTMF=0.5V
0.1
¾
¾
mA
¾
Row group, RL=5kW
120
155
180
mVrms
¾
THD£-23dB
5
¾
¾
kW
Column Pre-emphasis
¾
Row group=0dB
1
2
3
dB
Tone Signal Distortion
¾
RL=5kW
¾
-30
-23
dB
VTOL
DTMF Sink Current
¾
VTAC
DTMF Output AC Level
RL
DTMF Output Load
ACR
THD
Rev. 0.10
¾
5
October 1, 2002
Preliminary
HT95L100/10P
Functional Description
to fetch an instruction code, the contents of the program
counter are incremented by 1. The program counter
then points to the memory word containing the next instruction code.
Execution flow
The system clock for the telephone controller is derived
from a 32768Hz crystal oscillator. A built-in frequency up
conversion circuit provides dual system clock, namely;
32768Hz and 3.58MHz. The system clock is internally
divided into four non-overlapping clocks. One instruction cycle consists of four system clock cycles. Instruction fetching and execution are pipelined in such a way
that a fetch takes an instruction cycle while decoding
and execution takes the next instruction cycle. The
pipelining scheme causes each instruction to be effectively executed in a instruction cycle. If an instruction
changes the program counter, two instruction cycles are
required to complete the instruction.
When executing a jump instruction, conditional skip execution, loading PCL register, subroutine call, initial reset, internal interrupt, external interrupt or return from
subroutine, the program counter manipulates the program transfer by loading the address corresponding to
each instruction. The conditional skip is activated by instructions. Once the condition is met, the next instruction, fetched during the current instruction execution, is
discarded and a dummy cycle replaces it to get the
proper instruction. Otherwise proceed to the next instruction.
Program counter - PC
The program counter lower order byte register
(PCL:06H) is a readable and write-able register. Moving
data into the PCL performs a short jump. The destination will be within 256 locations. When a control transfer
takes place, an additional dummy cycle is required.
The program counter (PC) controls the sequence in
which the instructions stored in the program ROM are
executed and its contents specify a full range of program memory. After accessing a program memory word
S y s te m
C lo c k
T 1
T 2
T 3
T 4
T 1
T 2
P C
P C
T 3
T 4
T 1
T 2
P C + 1
F e tc h IN S T (P C )
E x e c u te IN S T (P C -1 )
T 3
T 4
P C + 2
F e tc h IN S T (P C + 1 )
E x e c u te IN S T (P C )
F e tc h IN S T (P C + 2 )
E x e c u te IN S T (P C + 1 )
Execution flow
Program Counter
Mode
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
Initial reset
0
0
0
0
0
0
0
0
0
0
0
0
External interrupt
0
0
0
0
0
0
0
0
0
1
0
0
Timer/Event Counter 0 overflow
0
0
0
0
0
0
0
0
1
0
0
0
Timer/Event Counter 1 overflow
0
0
0
0
0
0
0
0
1
1
0
0
RTC interrupt
0
0
0
0
0
0
0
1
0
1
0
0
Dialer I/O interrupt
0
0
0
0
0
0
0
1
1
0
0
0
Loading PCL
*11
*10
*9
*8
@7
@6
@5
@4
@3
@2
@1
@0
Jump, call branch
#11
#10
#9
#8
#7
#6
#5
#4
#3
#2
#1
#0
Return from subroutine
S11
S10
S9
S8
S7
S6
S5
S4
S3
S2
S1
S0
Skip
Program Counter+2
Note: *11~*0: Program counter bits
S11~S0: Stack register bits
#11~#0: Instruction code bits
Rev. 0.10
@7~@0: PCL bits
6
October 1, 2002
Preliminary
· Location 000CH
Program memory - ROM
This location is reserved for the Timer/Event Counter
1 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 1 overflow, the
Timer/Event Counter 1 interrupt is enabled and the
stack is not full, the program begins execution at location 000CH.
The program memory is used to store the program instructions which are to be executed. It also contains
data, table, and interrupt entries, and is organized into
4096´16 bits, addressed by the program counter and table pointer. Certain locations in the program memory are
reserved for special usage:
· Location 0014H
· Location 0000H
This location is reserved for real time clock (RTC) interrupt service program. When RTC generator is enabled and time-out occurs, the RTC interrupt is
enabled and the stack is not full, the program begins
execution at location 0014H.
This area is reserved for the initialization program. After chip power-on reset or external reset or WDT
time-out reset, the program always begins execution
at location 0000H.
· Location 0004H
· Location 0018H
This area is reserved for the external interrupt service
program. If the INT/TMR1 input pin is activated, the
external interrupt is enabled and the stack is not full,
the program begins execution at location 0004H.
This location is reserved for the HKS pin edge transition or HDI pin falling edge transition or HFI pin rising
edge transition. If this condition occurs, the dialer I/O
interrupt is enabled and the stack is not full, the program begins execution at location 18H.
· Location 0008H
This area is reserved for the Timer/Event Counter 0 interrupt service program. If a timer interrupt results
from a Timer/Event Counter 0 overflow, the
Timer/Event Counter 0 interrupt is enabled and the
stack is not full, the program begins execution at location 0008H.
0 0 0 H
0 0 8 H
0 0 C H
Table location
Any location in the ROM space can be used as look-up
tables. The instructions ²TABRDC [m]² (the current
page, one page=256 words) and ²TABRDL [m]² (the last
page) transfer the contents of the lower-order byte to the
specified data memory, and the higher-order byte to
TBLH (08H). Only the destination of the lower-order
byte in the table is well-defined, and the higher-order
byte of the table word is transferred to TBLH. The table
pointer (TBLP) is a read/write register (07H), which indicates the table location. Before accessing the table, the
location must be placed in the TBLP. The TBLH is read
only and cannot be restored. If the main routine and the
ISR (Interrupt Service Routine) both employ the table
read instruction, the contents of the TBLH in the main
routine are likely to be changed by the table read instruction used in the ISR. Errors will then occur. Hence,
simultaneously using the table read instruction in the
main routine and the ISR should be avoided. However, if
the table read instruction has to be applied in both the
main routine and the ISR, the interrupt is supposed to be
disabled prior to the table read instruction. It will not be
enabled until the TBLH has been backed-up. All table
related instructions require two cycles to complete the
operation. These areas may function as normal program memory depending on the requirements.
D e v ic e in itia liz a tio n p r o g r a m
0 0 4 H
E x te r n a l in te r r u p t s u b r o u tin e
T im e r /e v e n t c o u n te r 0 in te r r u p t s u b r o u tin e
T im e r /e v e n t c o u n te r 1 in te r r u p t s u b r o u tin e
0 1 4 H
R T C in te r r u p t s u b r o u tin e
0 1 8 H
D ia le r I/O
n 0 0 H
P ro g ra m
R O M
in te r r u p t s u b r o u tin e
L o o k - u p ta b le ( 2 5 6 w o r d s )
n F F H
L o o k - u p ta b le ( 2 5 6 w o r d s )
0 F F F H
HT95L100/10P
1 6 b its
N o te : n ra n g e s fro m
0 to 0 E H
Program memory
Instruction(s)
Table Location
*11
*10
*9
*8
*7
*6
*5
*4
*3
*2
*1
*0
TABRDC [m]
P11
P10
P9
P8
@7
@6
@5
@4
@3
@2
@1
@0
TABRDL [m]
1
1
1
1
@7
@6
@5
@4
@3
@2
@1
@0
Note: *11~*0: Table location bits
P11~P8: Current program counter bits
@7~@0: Table pointer bits
Rev. 0.10
7
October 1, 2002
Preliminary
HT95L100/10P
LCD display memory and general purpose memory.
Most are read/write, but some are read only.
Stack register
This is a special part of the memory which is used to
save the contents of the program counter only. The
stack is organized into 8 levels and is neither part of the
data nor part of the program space, and is neither readable nor write-able. The activated level is indexed by the
stack pointer (SP) and is neither readable nor write-able.
At a subroutine call or interrupt acknowledge signal, the
contents of the program counter are pushed onto the
stack. At the end of a subroutine or an interrupt routine,
signaled by a return instruction (RET or RETI), the program counter is restored to its previous value from the
stack. After a chip reset, the SP will point to the top of the
stack. If the stack is full and an interrupt takes place, the
interrupt request flag will be recorded but the acknowledge signal will be inhibited even if this interrupt is enabled. When the stack pointer is decremented (by RET
or RETI), the interrupt will be serviced. This feature prevents stack overflow allowing the programmer to use the
structure more easily. If the stack is full and a ²CALL² is
subsequently executed, stack overflow occurs and the
first entry will be lost (only the most recent eight return
addresses are stored).
The special function registers is located from 00H to
1FH. The embedded control register are located in the
memory areas from 20H to 3FH. The remaining space
which are not specified on the following table before the
40H are reserved for future expanded usage and reading these locations will get ²00H². The general purpose
data memory is divided into 6 banks. The banks in the
RAM are all addressed from 40H to 0FFH and they are
selected by setting the value of the bank pointer (BP).
All of the data memory areas can handle arithmetic,
logic, increment, decrement and rotate operations directly. Except for some dedicated bits, each bit in the
data memory can be set and reset by ²SET [m].i² and
²CLR [m].i². They are also indirectly accessible through
memory pointer registers (MP0 or MP1). The
bank1~bank10 are only indirectly accessible through
memory pointer 1 register (MP1).
The LCD display memory is located at bank 1BH. They
can be read and written to by the indirect addressing
mode using memory pointer 1 (MP1). To turn the display
On or Off, a ²1² or ²0² is written to the corresponding bit
of the memory area.
Data memory
The data memory is divided into four functional groups:
special function registers, embedded control register,
Special register, embedded control register, LCD display memory and general purpose RAM
BP
Address
Function
Description
Special function register
00
00
IAR0
Indirect addressing register 0
00
01
MP0
Memory pointer register 0
00
02
IAR1
Indirect addressing register 1
00
03
MP1
Memory pointer register 1
00
04
BP
00
05
ACC
Accumulator
00
06
PCL
Program counter lower-order byte register
00
07
TBLP
Table pointer
00
08
TBLH
Table higher-order byte register
Watchdog Timer option setting register
Bank pointer register
00
09
WDTS
00
0A
STATUS
00
0B
INTC0
Interrupt control register 0
00
0C
TMR0H
Timer/Event Counter 0 high-order byte register
00
0D
TMR0L
Timer/Event Counter 0 low-order byte register
00
0E
TMR0C
Timer/Event Counter 0 control register
00
0F
TMR1H
Timer/Event Counter 1 high-order byte register
00
10
TMR1L
Timer/Event Counter 1 low-order byte register
Rev. 0.10
Status register
8
October 1, 2002
Preliminary
BP
Address
Function
00
11
TMR1C
00
12
PA
00
13
PAC
00
14
PB
00
15
PBC
00
16
DIALERIO
00
1A
PE
00
1B
PEC
00
1E
INTC1
HT95L100/10P
Description
Timer/Event Counter 1 control register
Port A data register
Port A control register
Port B data register
Port B control register
Dialer I/O register
Port E data register (bit3~bit0)
Port E control register (bit3~bit0)
Interrupt control register 1
Embedded control register
00
20
DTMFC
DTMF generator control register
00
21
DTMFD
DTMF generator data register
00
22
LINE
Line control register
00
24
RTCC
Real time clock control register
00
26
MODE
Operation mode control register
00
28
LCDIO
LCD segment and I/O option register
00
2D
LCDC
LCD driver control register
00
2E
PFDC
PFD control register
00
2F
PFDD
PFD data register
General purpose RAM
00
40~FF
BANK0 RAM
General purpose RAM space
01
40~FF
BANK1 RAM
General purpose RAM space
02
40~FF
BANK2 RAM
General purpose RAM space
03
40~FF
BANK3 RAM
General purpose RAM space
04
40~FF
BANK4 RAM
General purpose RAM space
05
40~FF
BANK5 RAM
General purpose RAM space
LCD RAM display memory
1B
8C~9F
LCD RAM
LCD RAM mapping space for COM0~COM7
Indirect addressing register
Accumulator
Location 00H and 02H are indirect addressing registers
that are not physically implemented. Any read/write operation of [00H] and [02H] will access the memory
pointed to by MP0 and MP1, respectively. Reading location [00H] or [02H] indirectly returns the result 00H,
while writing it leads to no operation. MP0 is indirectly
addressable in bank0, but MP1 is available for all banks
by switch BP [04H]. If BP is unequal to 00H, the indirect
addressing mode to read/write operation from 00H~3FH
will return the result as same as the value of bank0.
The accumulator is closely related to ALU operations. It
is also mapped to location 05H of the data memory and
can operate with immediate data. All data movement
between two data memory locations must pass through
the accumulator.
The memory pointer registers MP0 and MP1 are 8-bits
registers, and the bank pointer register BP is 5-bits register.
· Logic operations (AND, OR, XOR, CPL)
Rev. 0.10
Arithmetic and logic unit - ALU
This circuit performs 8-bit arithmetic and logic operations and provides the following functions:
· Arithmetic operations (ADD, ADC, SUB, SBC, DAA)
· Rotation (RL, RR, RLC, RRC)
· Increment and Decrement (INC, DEC)
9
October 1, 2002
Preliminary
· Branch decision (SZ, SNZ, SIZ, SDZ, etc.)
Once an interrupt subroutine is serviced, all the other interrupts will be blocked (by hardware clearing the EMI
bit). This scheme may prevent any further interrupt nesting. Other interrupt requests may occur during this interval but only the interrupt request flag is recorded. If a
certain interrupt requires servicing within the service
routine, the EMI bit and the corresponding bit of the
INTC0 (INTC1) may be set to allow interrupt nesting.
The ALU not only saves the results of a data operation
but also changes the status register.
Status register - STATUS
This status register contains the carry flag (C), auxiliary
carry flag (AC), zero flag (Z), overflow flag (OV), power
down flag (PD), and watchdog time-out flag (TO). It also
records the status information and controls the operation sequence.
If the stack is full, any other interrupt request will not be
acknowledged, even if the related interrupt is enabled,
until the stack pointer is decremented. If immediate service is desired, the stack must be prevented from becoming full.
Except for the TO and PD flags, bits in the status register can be altered by instructions, similar to the other
registers. Data written into the status register will not
change the TO or PD flag. Operations related to the status register may yield different results from those intended. The TO flag can be affected only by system
power-up, a WDT time-out or executing the ²CLR WDT²
or ²HALT² instruction. The PD flag can be affected only
by executing the ²HALT² or ²CLR WDT² instruction or
during a system power-up.
All these kinds of interrupts have a wake-up capability.
As an interrupt is serviced, a control transfer occurs by
pushing the program counter onto the stack, followed by
a branch to a subroutine at specified location in the program memory. Only the program counter is pushed onto
the stack. If the contents of the register or status register
(STATUS) are altered by the interrupt service program
which corrupts the desired control sequence, the contents should be saved in advance.
The Z, OV, AC and C flags generally reflect the status of
the latest operations.
External interrupt is triggered by a high to low transition
of the INT/TMR1 pin and the interrupt request flag EIF
will be set. When the external interrupt is enabled, the
stack is not full and the external interrupt is active, a subroutine call to location 04H will occur. The interrupt request flag EIF and EMI bits will be cleared to disable
other interrupts.
On entering the interrupt sequence or executing the
subroutine call, the status register will not be automatically pushed onto the stack.
If the contents of the status are important and if the subroutine can corrupt the status register, precautions must
be taken to save it .
The Timer/Event Counter 0 interrupt is generated by a
timeout overflow and the interrupt request flag T0F will
be set. When the Timer/Event Counter 0 interrupt is enabled, the stack is not full and the T0F bit is set, a subroutine call to location 08H will occur. The interrupt
request flag T0F and EMI bits will be cleared to disable
further interrupts.
Interrupt
The telephone controller provides an external interrupt,
internal timer/event counter interrupt, an internal real
time clock interrupt and internal dialer I/O interrupt. The
Interrupt Control Registers 0 and Interrupt Control Register 1 both contains the interrupt control bits that set the
enable/disable and the interrupt request flags.
Register
STATUS
(0AH)
Label
Bits
Function
C
0
C is set if the operation results in a carry during an addition operation or if a borrow
does not take place during a subtraction operation; otherwise C is cleared. Also it is
affected by a rotate through carry instruction.
AC
1
AC is set if the operation results in a carry out of the low nibbles in addition or no borrow from the high nibble into the low nibble in subtraction; otherwise AC is cleared.
Z
2
Z is set if the result of an arithmetic or logic operation is 0; otherwise Z is cleared.
OV
3
OV is set if the operation results in a carry into the highest-order bit but not a carry
out of the highest-order bit, or vice versa; otherwise OV is cleared.
PD
4
PD is cleared when either a system power-up or executing the CLR WDT instruction.
PD is set by executing the HALT instruction.
TO
5
TO is cleared by a system power-up or executing the CLR WDT or HALT instruction.
TO is set by a WDT time-out.
¾
Rev. 0.10
HT95L100/10P
6, 7
Unused bit, read as ²0²
10
October 1, 2002
Preliminary
Register
INTC0
(0BH)
INTC1
(1EH)
HT95L100/10P
Bits
Label
R/W
Function
0
EMI
RW
Controls the master (global) interrupt (1=enabled; 0=disabled)
1
EEI
RW
Controls the external interrupt (1=enabled; 0=disabled)
2
ET0I
RW
Controls the Timer/Event Counter 0 interrupt (1=enabled; 0=disabled)
3
ET1I
RW
Controls the Timer/Event Counter 1 interrupt (1=enabled; 0=disabled)
4
EIF
RW
External interrupt request flag (1=active; 0=inactive)
5
T0F
RW
Timer/Event Counter 0 request flag (1=active; 0=inactive)
6
T1F
RW
Timer/Event Counter 1 request flag (1=active; 0=inactive)
7
¾
RO
Unused bit, read as ²0²
0
¾
RO
Unused bit, read as ²0²
1
ERTCI
RW
Control the real time clock interrupt (1=enable; 0=disable)
2
EDRI
RW
Control the dialer I/O interrupt (1=enable; 0=disable)
3
¾
RO
Unused bit, read as ²0²
4
¾
RO
Unused bit, read as ²0²
5
RTCF
RW
Internal real time clock interrupt request flag (1=active; 0=inactive)
6
DRF
RW
Internal dialer I/O interrupt request flag (1=active: 0=inactive)
7
¾
RO
Unused bit, read as ²0²
the latter of the two T2 pulses, if the corresponding interrupts are enabled. In the case of simultaneous requests
the following table shows the priority that is applied.
These can be masked by resetting the EMI bit.
The Timer/Event Counter 1 interrupt is generated by a
timeout overflow and the interrupt request flag T1F will
be set. When the Timer/Event Counter 1 interrupt is enabled, the stack is not full and the T1F bit is set, a subroutine call to location 0CH will occur. The interrupt
request flag T1F and EMI bits will be cleared to disable
further interrupts.
Interrupt Source
The real time clock interrupt is generated by a 1Hz RTC
generator. When the RTC time-out occurs, the interrupt
request flag RTCF will be set. When the RTC interrupt is
enabled, the stack is not full and the RTCF is set, a subroutine call to location 14H will occur. The interrupt request flag RTCF and EMI bits will be cleared to disable
other interrupts.
Priority
Vector
External interrupt
1
04H
Timer/Event Counter 0 interrupt
2
08H
Timer/Event Counter 1 interrupt
3
0CH
Real time clock interrupt
4
14H
Dialer I/O interrupt
5
18H
Priority of the interrupt
The dialer I/O interrupt is triggered by any edge transition onto HKS pin or a falling edge transition onto HDI
pin or a rising edge transition onto HFI pin, the interrupt
request flag DRF will be set. When the dialer I/O interrupt is enabled, the stack is not full and the DRF is set, a
subroutine call to location 18H will occur. The interrupt
request flag DRF and EMI bits will be cleared to disable
other interrupts.
EMI, EEI, ET0I, ET1I, ERTCI and EDRI are used to control the enabling/disabling of interrupts. These bits prevent the requested interrupt from being serviced. Once
the interrupt request flags (EIF, T0F, T1F, RTCF, DRF)
are set by hardware or software, they will remain in the
INTC0 or INTC1 registers until the interrupts are serviced or cleared by a software instruction.
It is recommended that a program should not use the
²CALL subroutine² within the interrupt subroutine. Interrupts often occur in an unpredictable manner or need to
be serviced immediately in some applications. If only
one stack is left and enabling the interrupt is not well
controlled, the original control sequence will be damaged once the ²CALL² operates in the interrupt subroutine.
During the execution of an interrupt subroutine, other interrupt acknowledge signals are held until the RETI instruction is executed or the EMI bit and the related
interrupt control bit are set to 1 (if the stack is not full). To
return from the interrupt subroutine, ²RET² or ²RETI²
may be invoked. RETI will set the EMI bit to enable an
interrupt service, but RET will not.
Interrupts, occurring in the interval between the rising
edges of two consecutive T2 pulses, will be serviced on
Rev. 0.10
11
October 1, 2002
Preliminary
Oscillator configuration
period. By invoking the WDT prescaler, longer time-out
periods can be realized. Writing data to WS2, WS1,
WS0 can give different time-out periods.
There are two oscillator circuits in the controller, the external 32768Hz crystal oscillator and internal WDT
OSC.
The WDT OSC period is 78ms. This time-out period may
vary with temperature, VDD and process variations. The
WDT OSC always works for any operation mode.
The 32768Hz crystal oscillator and frequency-up conversion circuit (32768Hz to 3.58MHz) are designed for
dual system clock source. It is necessary for frequency
conversion circuit to add external RC components to
make up the low pass filter that stabilize the output frequency 3.58MHz (see the oscillator circuit).
If the instruction clock is selected as the WDT clock
source, the WDT operates in the same manner except
in the Sleep mode or Idle mode. In these two modes, the
WDT stops counting and lose its protecting purpose. In
this situation the logic can only be re-started by external
logic.
The WDT OSC is a free running on-chip RC oscillator,
and no external components are required. Even if the
system enters the Idle mode (the system clock is
stopped), the WDT OSC still works within a period of
78ms normally. When the WDT is disabled or the WDT
source is not this RC oscillator, the WDT OSC will be
disabled.
If the WDT clock source is the 32768Hz, the WDT also
operates in the same manner except in the Idle mode.
When in the Idle mode, the 32768Hz stops, the WDT
stops counting and lose its protecting purpose. In this
situation the logic can only be re-started by external
logic.
X 1
X 2
The high nibble and bit3 of the WDTS are reserved for
user defined flags, which can be used to indicate some
specified status.
1 5 k W
X C
3 n
The WDT time-out under Normal mode or Green mode
will initialize ²chip reset² and set the status bit ²TO². But
in the Sleep mode or Idle mode, the time-out will initialize a ²warm reset² and only the program counter and
stack pointer are reset to 0. To clear the WDT contents
(including the WDT prescaler), three methods are
adopted; external reset (a low level to RES pin), software instruction and a ²HALT² instruction.
5 0 n
System oscillator circuit
Watchdog Timer - WDT
The WDT clock source is implemented by a WDT OSC
or external 32768Hz or an instruction clock (system
clock divided by 4), determined by the mask option. This
timer is designed to prevent a software malfunction or
sequence from jumping to an unknown location with unpredictable results. The Watchdog Timer can be disabled by mask option. If the Watchdog Timer is disabled,
all the executions related to the WDT result in no operation.
The software instruction include ²CLR WDT² and the
other set ²CLR WDT1² and ²CLR WDT2². Of these two
types of instruction, only one can be active depending
on the mask option ²WDT instr². If the ²CLR WDT² is selected (i.e. One clear instruction), any execution of the
3 2 7 6 8 H z
W D T O S C
S y s te m
If the device operates in a noisy environment, using the
on-chip WDT OSC or 32768Hz crystal oscillator is
strongly recommended.
WDTS
(09H)
Rev. 0.10
Label
Bits
C lo c k /4
W D T P r e s c a le r
M a s k
O p tio n
S e le c t
9 - b it C o u n te r
W S 0 ~ W S 2
When the WDT clock source is selected, it will be first divided by 512 (9-stage) to get the n o m i nal t i m e - o u t
Register
HT95L100/10P
7 - b it C o u n te r
8 -to -1 M U X
W D T T im e - o u t
Watchdog Timer
R/W
Function
WS0
WS1
WS2
0
1
2
RW
Watchdog Timer division ratio selection bits
Bit 2, 1, 0=000, Division ratio=1:1
Bit 2, 1, 0=001, Division ratio=1:2
Bit 2, 1, 0=010, Division ratio=1:4
Bit 2, 1, 0=011, Division ratio=1:8
Bit 2, 1, 0=100, Division ratio=1:16
Bit 2, 1, 0=101, Division ratio=1:32
Bit 2, 1, 0=110, Division ratio=1:64
Bit 2, 1, 0=111, Division ratio=1:128
¾
7~3
RW
Unused bit. These bits are read/write-able.
12
October 1, 2002
Preliminary
· Green mode to Normal mode:
CLR WDT instruction will clear the WDT. In the case that
²CLR WDT1² and ²CLR WDT2² are chosen (i.e. Two
clear instructions), these two instructions must be executed to clear the WDT; otherwise, the WDT may reset
the chip as a result of time-out.
Step 1: Set UPEN to 1
Step 2: Software delay 20ms at least
Step 3: Set MODE1 to 1
After Step 3, operation mode is changed to Normal
mode.
Controller operation mode
· Sleep mode or Idle mode to Green mode:
Holtek¢s telephone controllers support two system clock
and four operation modes. The system clock could be
32768Hz or 3.58MHz and operation mode could be Normal, Green, Sleep or Idle mode. These are all selected
by the software.
Method 1: Any reset condition occurred
Method 2: Any interrupt is active
Method 3: Port A wake-up
Note: The Timer 0, Timer 1, RTC and dialer I/O interrupt function will not work at the Idle mode because the 32768Hz crystal is stopped.
The following conditions will force the operation mode to
change to Green mode:
· Any reset condition from any operation mode
The reset conditions include power on reset, external reset, WDT time-out reset. By examining the processor
status flag, PD and TO, the program can distinguish between different ²reset conditions². Refer to the Reset
function for detailed description.
· Any interrupt from Sleep mode or Idle mode
· Port A wake-up from Sleep mode or Idle mode
How to change the Operation Mode
· Normal mode to Green mode:
Clear MODE1 to 0, then operation mode is changed to
Green mode but the UPEN status is not changed.
However, UPEN can be cleared by software.
The port A wake-up and interrupt can be considered as
a continuation of normal execution. Each bit in port A
can be independently selected to wake-up the device by
mask option. Awakening from Port A stimulus, the program will resume execution of the next instruction.
· Normal mode or Green mode to Sleep mode:
Any valid interrupts from Sleep mode or Idle mode may
cause two sequences. One is if the related interrupt is
disabled or the interrupt is enabled but the stack is full,
the program will resume execution at the next instruction. The other is if the interrupt is enabled and the stack
is not full, the regular interrupt response takes place. It is
necessary to mention that if an interrupt request flag is
set to ²1² before entering the Sleep mode or Idle mode,
the wake-up function of the related interrupt will be disabled.
Step 1: Clear MODE0 to 0
Step 2: Execute HALT instruction
After Step 2, operation mode is changed to Sleep
mode, the UPEN and MODE1 are cleared to 0 by
hardware.
· Normal mode or Green mode to Idle mode:
Step 1: Set MODE0 to 1
Step 2: Execute HALT instruction
After Step 2, operation mode is changed to Idle mode,
the UPEN and MODE1 are cleared to 0 by hardware.
Register
MODE
(26H)
HT95L100/10P
Label
Bits
R/W
Function
¾
4~0
RO
Unused bit, read as ²0²
UPEN
5
RW
1: Enable frequency up conversion function to generate 3.58MHz
0: Disable frequency up conversion function to generate 3.58MHz
MODE0
6
RW
1: Disable 32768Hz oscillator while the HALT instruction is executed
(Idle mode)
0: Enable 32768Hz oscillator while the HALT instruction is executed
(Sleep mode)
MODE1
7
RW
1: Select 3.58MHz as CPU system clock
0: Select 32768Hz as CPU system clock
Operation mode description
HALT
Instruction
MODE1
MODE0
UPEN
Operation
Mode
32768Hz
3.58MHz
System
Clock
Not execute
1
X
1
Normal
Not execute
0
X
0
Green
ON
ON
3.58MHz
ON
OFF
32768Hz
Be executed
0
0
0
Sleep
ON
OFF
HALT
Be executed
0
1
0
Idle
OFF
OFF
HALT
Note: ²X² means don¢t care
Rev. 0.10
13
October 1, 2002
Preliminary
Once a Sleep mode or Idle mode wake-up event occurs,
it will take SST delay time (1024 system clock period) to
resume to Green mode. In other words, a dummy period
is inserted after a wake-up. If the wake-up results from
an interrupt acknowledge signal, the actual interrupt
subroutine execution will be delayed by one or more cycles. If the wake-up results in the next instruction execution, this will be executed immediately after the dummy
period is finished.
HT95L100/10P
H A L T
W D T
E x te rn a l
W a rm
W D T tim e - o u t
C o ld R e s e t
R E S
S S T
1 0 - b it R ip p le
C o u n te r
S Y S C L K
S y s te m
To minimize power consumption, all the I/O pins should
be carefully managed before entering the Sleep mode
or Idle mode.
R e s e t
R e s e t
Reset configuration
V D D
The Sleep mode or Idle mode is initialized by the HALT
instruction and results in the following.
· The system clock will be turned off.
R E S
tS
S T
S S T T im e - o u t
· The WDT function will be disabled if the WDT clock
source is the instruction clock.
C h ip
· The WDT function will be disabled if the WDT clock
R e s e t
Reset timing chart
source is the 32768Hz in Idle mode.
· The WDT will still function if the WDT clock source is
By examining the processor status flags PD and TO, the
software program can distinguish between the different
²chip resets².
the WDT OSC.
· If the WDT function is still enabled, the WDT counter
and WDT prescaler will be cleared and recounted
again.
· The contents of the on chip RAM and registers remain
unchanged.
· All the I/O ports maintain their original status.
· The flag PD is set and the flag TO is cleared by hard-
TO
PD
0
0
Power on reset
u
u
External reset during Normal mode or
Green mode
0
1
External reset during Sleep mode or
Idle mode
1
u
WDT time-out during Normal mode or
Green mode
1
1
WDT time-out during Sleep mode or
Idle mode
ware.
Reset
There are three ways in which a reset can occur.
· Power on reset.
· A low pulse onto RES pin.
· WDT time-out.
Note: ²u² means ²unchanged²
After these reset conditions, the Program Counter and
Stack Pointer will be cleared to 0.
The functional units chip reset status are shown below:
To guarantee that the system oscillator is started and
stabilized, the SST (System Start-up Timer) provides an
extra-delay of 1024 system clock pulses when the system is reset or awakes from the Sleep or Idle operation
mode.
V
Reset Condition
D D
Program Counter
000H
Interrupt
Disabled
Prescaler
Cleared
WDT
Cleared
After a master reset, WDT
begins counting.
(If WDT function is enabled
by mask option)
1 0 0 k W
Timer/Event Counter 0/1 Off
R E S
0 .1 m F
Input/output Port
Input mode
Stack Pointer
Points to the top of the stack
Reset circuit
Rev. 0.10
14
October 1, 2002
Preliminary
HT95L100/10P
When the reset conditions occurred, some registers may be changed or unchanged.
Reset Conditions
Register
Addr.
IAR0
MP0
Power On
RES Pin
RES Pin
(Sleep/Idle)
WDT
WDT
(Sleep/Idle)
00H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
01H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
IAR1
02H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
MP1
03H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
BP
04H
---0 0000
---0 0000
---0 0000
---0 0000
---u uuuu
ACC
05H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
PCL
06H
0000H
0000H
0000H
0000H
0000H
TBLP
07H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TBLH
08H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
WDTS
09H
0000 0111
0000 0111
0000 0111
0000 0111
uuuu uuuu
STATUS
0AH
--00 xxxx
--uu uuuu
--01 uuuu
--1u uuuu
--11 uuuu
INTC0
0BH
-000 0000
-000 0000
-000 0000
-000 0000
-uuu uuuu
TMR0H
0CH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0L
0DH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR0C
0EH
00-0 1---
00-0 1---
00-0 1---
00-0 1---
uu-u u----
TMR1H
0FH
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1L
10H
xxxx xxxx
uuuu uuuu
uuuu uuuu
uuuu uuuu
uuuu uuuu
TMR1C
11H
00-0 1---
00-0 1---
00-0 1---
00-0 1---
uu-u u----
PA
12H
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PAC
13H
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PB
14H
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
PBC
15H
1111 1111
1111 1111
1111 1111
1111 1111
uuuu uuuu
DialerIO
16H
111x xxxx
111x xxxx
111x xxxx
111x xxxx
uuuu uuuu
PE
1AH
---- 1111
---- 1111
---- 1111
---- 1111
---- uuuu
PEC
1BH
---- 1111
---- 1111
---- 1111
---- 1111
---- uuuu
INTC1
1EH
-000 -000
-000 -000
-000 -000
-000 -000
-uuu -uuu
DTMFC
20H
---- -0-1
---- -0-1
---- -0-1
---- -0-1
---- -u-u
DTMFD
21H
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
LINE
22H
0--- ----
u--- ----
u--- ----
u--- ----
u--- ----
RTCC
24H
0-0- ----
u-u- ----
u-u- ----
u-u- ----
u-u- ----
MODE
26H
000- ----
00u- ----
000- ----
00u- ----
000- ----
LCDIO
28H
--0- ----
--u- ----
--u- ----
--u- ----
--u- ----
LCDC
2DH
0000 -0--
uuuu -u--
uuuu -u--
uuuu -u--
uuuu -u--
PFDC
2EH
0000 ----
0000 ----
0000 ----
0000 ----
uuuu ----
PFDD
2FH
0000 0000
0000 0000
0000 0000
0000 0000
uuuu uuuu
x
u
u
u
u
RAM (Data & LCD)
Note:
²u² means ²unchanged²
²x² means ²unknown²
²-² means ²unused²
Rev. 0.10
15
October 1, 2002
Preliminary
register (16-bit). The Timer/Event Counter 0 preload
register is changed by writing TMR0H operations. Writing TMR0L will keep the Timer/Event Counter 0 preload
register unchanged.
Timer/Event Counter
Two timer/event counters (TMR0, TMR1) are implemented in the telephone controller series. The
Timer/Event Counter 0 and Timer/Event Counter 1 contain 16-bits programmable count-up counter and the
clock may come from an external source or internal
source. For TMR0 internal source is instruction clock
(system clock/4). For TMR1 internal source is 32768Hz.
Reading TMR0H latches the TMR0L into the low byte
buffer to avoid a false timing problem. Reading TMR0L
returns the contents of the low byte buffer. In other
words, the low byte of the Timer/Event Counter 0 can
not be read directly. It must read the TMR0H first to
make the low byte contents of Timer/Event Counter 0 be
latched into the buffer.
Using the 32768Hz clock or instruction clock, there is
only one reference time-base. The external clock input
allows the user to count external events, measure time
intervals or pulse width, or generate an accurate time
base.
There are 3 registers related to the Timer/Event Counter
1; TMR1H, TMR1L, TMR1C. The Timer/Event Counter
1 operates in the same manner as the Timer/Event
Counter 0.
There are 3 registers related to Timer/Event Counter 0;
TMR0H, TMR0L, TMR0C. Writing TMR0L only writes
the data into a low byte buffer, but writing TMR0H simultaneously writes the data along with the contents of the
low byte buffer into the Timer/Event Counter 0 preload
T im e r 0 : In s tr u c tio n c lo c k ( s y s te m
T im e r 1 : 3 2 7 6 8 H z
The TMR0C is the Timer/Event Counter 0 control register, which defines the Timer/Event Counter 0 options.
The Timer/Event Counter 1 has the same options as the
c lo c k /4 )
D a ta B u s
T M 1
T M 0
IN T /T M R 1
T M R 0
T im e r /E v e n t C o u n te r 0 /1
P r e lo a d R e g is te r
T E
R e lo a d
T im e r /e v e n t
C o u n te r 0 /1
P u ls e W id th
M e a s u re m e n t
M o d e C o n tro l
T M 1
T M 0
T O N
HT95L100/10P
L o w
O v e r flo w
to In te rru p t
B y te B u ffe r
Timer/Event Counter 0/1
Register
Label
Bits
R/W
¾
0~2
RO
Unused bit, read as ²0²
TE
3
RW
To define the TMR0/TMR1 active edge of timer
For event count or Timer mode
(0=active on low to high; 1=active on high to low)
For pulse width measurement mode
(0=measures low pulse width; 1=measures high pulse width)
TON
4
RW
To enable/disable timer counting (0=disabled; 1=enabled)
¾
5
RO
Unused bit, read as ²0²
RW
To define the operating mode
Bit 7, 6=01, Event count mode (external clock)
Bit 7, 6=10, Timer mode
Bit 7, 6=11, Pulse width measurement mode
Bit 7, 6=00, Unused
TMR0C
(0EH)
TMR1C
(11H)
Function
TM0
TM1
6
7
Register
Bits
R/W
TMR0H (0CH)
0~7
RW
Function
Timer/Event Counter 0 higher-order byte register
TMR0L (0DH)
0~7
RW
Timer/Event Counter 0 lower-order byte register
TMR1H (0FH)
0~7
RW
Timer/Event Counter 1 higher-order byte register
TMR1L (10H)
0~7
RW
Timer/Event Counter 1 lower-order byte register
Rev. 0.10
16
October 1, 2002
Preliminary
For input operation, these ports are non-latching, that is,
the inputs must be ready at the T2 rising edge of instruction ²MOV A,[m]² (m=12H, 14H or 1AH). For output operation, all the data is latched and remains unchanged
until the output latch is rewritten.
Timer/Event Counter 0 and is defined by TMR1C. The
timer/event counter control registers define the operating mode, counting enable or disable and active edge.
The TM0, TM1 bits define the operating mode. The
event count mode is used to count external events,
which means the clock source comes from an external
(TMR0 or INT/TMR1) pin. The timer mode functions as
a normal timer with the clock source coming from instruction clock (TMR0) or 32768Hz (TMR1). The pulse
width measurement mode can be used to count the high
or low level duration of the external signal (TMR0 or
INT/TMR1). The counting is based on the 32768Hz
clock for TMR1 or instruction clock for TMR0.
Each I/O line has its own control register (PAC,PBC,
PEC) to control the input/output configuration. With this
control register, CMOS output or Schmitt trigger input
can be reconfigured dynamically under software control.
To make one I/O line to function as an input line, the corresponding latch of the control register must be written
with a ²1². The pull-high resistance shows itself automatically if the pull-high option is selected. The input
source also depends on the control register. If the control register bit is ²1², the input will read the pad state. If
the control register bit is ²0², the contents of the latches
will move to the internal bus. The latter is possible in the
²read-modify-write² instruction. For output function,
CMOS is the only configuration. Each bit of these input/output latches can be set or cleared by ²SET [m].i²
and ²CLR [m].i² (m=12H, 14H or 1AH) instructions.
In the event count or timer mode, once the timer/event
counter starts counting, it will count from the current
contents in the timer/event counter to FFFFH. If an overflow occurs, the counter is reloaded from the timer/event
counter preload register and generates the corresponding interrupt request flag (T0F/T1F) at the same time.
In pulse width measurement mode with the TON and TE
bits equal to 1, once the TMR0/TMR1 pin has received a
transient from low to high (or high to low; if the TE bit is
0) it will start counting until the TMR0/TMR1 pin returns
to the original level and resets the TON. The measured
result will remain in the timer/event counter even if the
activated transient occurs again. In other words, only 1
cycle measurement can be done. Until setting the TON,
the cycle measurement will function again as long as it
receives further transient pulse. Note that, in this operating mode, the timer/event counter starts counting not
according to the logic level but according to the transient
edges. In the case of counter overflows, the counter is
reloaded from the timer/event counter preload register
and continue to measure the width and issues the interrupt request just like the other two modes.
Some instructions first input data and then follow the
output operations. For example, ²SET [m].i², ²CLR
[m].i², ²CPL [m]², ²CPLA [m]² read the entire port states
into the CPU, execute the defined operations
(bit-operation), and then write the results back to the
latches or the accumulator.
Each line of port A has the capability of waking-up the
device. They are selected by mask option per bit.
There is a pull-high option available for all I/O lines.
Once the pull-high option of an I/O line is selected, the
I/O lines have pull-high resistor. Otherwise, the pull-high
resistor is absent. It should be noted that a non-pull-high
I/O line operating in input mode may cause a floating
state.
To enable the counting operation, the timer on bit (TON)
should be set to 1. In the pulse width measurement
mode, the TON will be cleared automatically after the
measurement cycle is completed. But in the other two
modes the TON can only be reset by instruction. The
overflow of the timer/event counter is one of the
wake-up sources. No matter what the operation mode
is, writing a 0 to ET0I/ET1I can disable the corresponding interrupt service.
I/O port pull-high, wake-up function are selected by
mask option
In the case of timer/event counter off condition, writing
data to the timer/event counter preload register also reloads that data to the timer/event counter. But if the
timer/event counter is turned on, data written to the
timer/event counter is reserved only in the timer/event
counter preload register. The timer/event counter will go
on operating until an overflow occurs.
Input
I/O
Port
Output
PA
CMOS
Selected per bit
Selected
per bit
PB
CMOS
Selected per bit
X
PE
CMOS
Selected per nibble
X
Pull-high
Resistor
Wake-up
Function
Note: X: unavailable
The PE0~PE3 and SEG16~SEG19 share the same
pads. They can be selected per nibble by software option at any time.
When the PE0~PE3 are not selected, the I/O port control register, PEC (1BH) could be read/write-able and be
used as a general user RAM, but this function is not
available for register PE (1AH).
Input/output ports
There are 20 bidirectional input/output lines in the telephone controller, labeled as PA, PB and PE. All of these
I/O ports can be used for input and output operations.
Rev. 0.10
HT95L100/10P
17
October 1, 2002
Preliminary
Register
Label
Bits
R/W
¾
0~4
6~7
RO
Unused bit, read as ²0²
SPE0
5
RW
0: SEG16~ SEG19 pins are LCD segment output
1: SEG16~ SEG19 pins are PE0~PE3 pins
LCDIO
(28H)
Function
DTMF generator
The power down mode (D_PWDN=1) will terminate all
the DTMF generator function, however, the registers
DTMFC and DTMFD are accessible at this power down
mode.
The DTMF (Dual Tone Multiple-Frequency) signal generator is implemented in the telephone controller. It can
generate 16 dual tones and 8 single tones from the
DTMF pin. This generators also support power down,
tone on/off function. The DTMF generator clock source
is 3.58MHz, before using this function, the system operation mode must be at Normal mode.
Register
DTMFC
(20H)
DTMFD
(21H)
HT95L100/10P
The duration of DTMF output should be handled by the
software. DTMFD register value could be changed as
desired, the DTMF pin will output the new dual-tone simultaneously.
Label
Bits
R/W
Function
D_PWDN
0
RW
DTMF generator power down
1: DTMF generator is at power down mode.
0: DTMF generator is at operation mode.
¾
1
RO
Unused bit, read as ²0²
TONE
2
RW
Tone output enable
1: DTMF signal output is enabled.
0: DTMF signal output is disabled.
¾
7~3
RO
Unused bit, read as ²0²
TC4~TC1
3~0
RW
To set high group frequency
TR4~TR1
7~4
RW
To set low group frequency
The DTMF pin output is controlled by the combination of the D_PWDN, TONE, TR~TC value.
Control Register Bits
D_PWDN
DTMF Pin Output Status
TONE
TR4~TR1/TC4~TC1
1
x
x
0
0
0
x
1/2 VDD
0
1
0
1/2 VDD
0
1
Any valid value
16 dual tones or 8 signal tones, bias with 1/2 VDD
D _ P D W N = 0
D _ P D W N = 1
1 /2 V D D
T O N E = 1
T O N E = 0
T O N E = 1
T O N E = 0
T O N E = 1
T O N E = 0
A ll th e tim in g o f th e T O N E = 1 a n d T O N E = 0 a r e d e te r m in e d b y s o ftw a r e
DTMF output
Rev. 0.10
18
October 1, 2002
Preliminary
HT95L100/10P
Tone frequency
Output Frequency (Hz)
% Error
Specified
Actual
697
699
+0.29%
770
766
-0.52%
852
847
-0.59%
941
948
+0.74%
1209
1215
+0.50%
1336
1332
-0.30%
1477
1472
-0.34%
% Error does not contain the crystal frequency shift
DTMF frequency selection table: register DTMFD[21H]
Low Group
High Group
DTMF Output
TR4
TR3
TR2
TR1
TC4
TC3
TC2
TC1
Low
High
DTMF
Code
0
0
0
1
0
0
0
1
697
1209
1
0
0
0
1
0
0
1
0
697
1336
2
0
0
0
1
0
1
0
0
697
1477
3
0
0
0
1
1
0
0
0
697
1633
A
0
0
1
0
0
0
0
1
770
1209
4
0
0
1
0
0
0
1
0
770
1336
5
0
0
1
0
0
1
0
0
770
1477
6
0
0
1
0
1
0
0
0
770
1633
B
0
1
0
0
0
0
0
1
852
1209
7
0
1
0
0
0
0
1
0
852
1336
8
0
1
0
0
0
1
0
0
852
1477
9
0
1
0
0
1
0
0
0
852
1633
C
1
0
0
0
0
0
0
1
941
1209
*
1
0
0
0
0
0
1
0
941
1336
0
1
0
0
0
0
1
0
0
941
1477
#
1
0
0
0
1
0
0
0
941
1633
D
0
0
0
1
0
0
0
0
697
0
0
1
0
0
0
0
0
770
0
1
0
0
0
0
0
0
852
1
0
0
0
0
0
0
0
941
Single tone for testing only
0
0
0
0
0
0
0
1
1209
0
0
0
0
0
0
1
0
1336
0
0
0
0
0
1
0
0
1477
0
0
0
0
1
0
0
0
1633
Writing other values to TR4~TR1, TC4~TC1 may generate an unpredictable tone.
Rev. 0.10
19
October 1, 2002
Preliminary
HT95L100/10P
Dialer I/O function
A special dialer I/O circuit is built into the telephone controller for dialing application. These specially designed I/O cells
allows the controller to work under a low voltage condition that usually happens when the subscriber¢s loop is long.
Dialer I/O pin function:
Name
I/O
Description
XMUTE
NMOS Output
XMUTE pin output is controlled by software. This is an NMOS open drain structure
pulled to VSS during dialing signal transmission. Otherwise, it is an open circuit.
XMUTE is used to mute the speech circuit when transmitting the dialer signal.
DNPO
NMOS Output
DNPO pin is an NMOS output, usually by means of software to make/break the line.
This pin is only controlled by software.
PO
CMOS Output
This pin is controlled by the HKS, HFI and HDI pins.
When PO pin is high, the telephone line is make.
When PO pin is low, the telephone line is break.
HKS
Schmitt Trigger
Input
This pin controls the PO pin directly.
This pin is used to monitor the status of the hook-switch and its combination with
HFI/HDI can control the PO pin output to make or break the line.
A rising edge to HKS pin will cause the dialer I/O to be on-hook status and generate
an interrupt, its vector is 18H.
A falling edge to HKS pin will cause the dialer I/O to be off-hook status and clear HFO
and HDO flags to 0. This falling edge will also generate an interrupt, its vector is 18H.
HDO
CMOS Output
This pin is controlled directly by HDI, HKS and HFI pin.
When HDO pin is high, the hold-line function is enabled and PO outputs a high signal
to make the line.
HDI
Schmitt Trigger
Input
A low pulse to HDI pin (hold-line function request) will clear HFO to 0 and toggle HDO
and generates an interrupt, its vector is 18H.
This pin controls the HFO and HDO pins directly.
This pin is functional only when the line is made, that is, off-hook or hand-free
(PO output high signal).
HFO
CMOS Output
This pin is controlled directly by HFI, HDI and HKS pins.
When HFO pin is high, the hand-free function is enabled and PO outputs a high
signal to make the line.
HFI
Schmitt Trigger
Input
A high pulse to HFI pin (hand-free function request) will clear HDO to 0 and toggle
HFO and generates an interrupt, its vector is 18H.
This pin controls the PO, HFO and HDO pins directly.
The following are the recommended circuit for HFI and HDI pins.
V
D D
V
1 0 k W
H D I P in
H F I P in
0 .1 m F
Rev. 0.10
In te r n a l P u ll- lo w
2 0 0 k W
1 0 k W
20
D D
In te r n a l P u ll- h ig h 2 0 0 k W
0 .1 m F
October 1, 2002
Preliminary
HT95L100/10P
Phone controller also supports the dialer I/O flag to monitor the dialer status.
Register
DIALERIO
(16H)
Label
Bits
R/W
Function
HFI
0
RO
1: The HFI pin level is 1.
0: The HFI pin level is 0.
HFO
1
RO
1: The HFO pin level is 1.
0: The HFO pin level is 0.
HDI
2
RO
1: The HDI pin level is 1.
0: The HDI pin level is 0.
HDO
3
RO
1: The HDO pin level is 1.
0: The HDO pin level is 0.
HKS
4
RO
1: The HKS pin level is 1.
0: The HKS pin level is 0.
SPO
5
RW
1: The PO pin is controlled by the combination of the HKS, HFI and HDI pin.
0: The PO pin level is set to 0 by software.
SDNPO
6
RW
1: The DNPO pin level is set to floating by software.
0: The DNPO pin level is set to 0 by software.
XMUTE
7
RW
1: The XMUTE pin is set to floating by software.
0: The XMUTE pin is set to 0 by software.
The SPO flag is special designed to control the PO. When the flag SPO is set to 1, the PO pin is controlled by the combination of the HKS pin, HFI pin and HDI pin. The PO pin will always be 0 if the flag SPO=0.
The relation between the Dialer I/O function (SPO=1)
Dialer I/O Pin (Flag) Status
Dialer Function
Result
HKS
HFO
HDO
PO
DNPO
Telephone Line
On-hook
1
0
0
0
floating
break
On-hook & Hand-free
1
1
0
1
floating
make
On-hook & Hold-line
1
0
1
1
floating
make
Off-hook
0
0
0
1
floating
make
Off-hook & Hand-free
0
1
0
1
floating
make
Off-hook & Hold-line
0
0
1
1
floating
make
The following describes the dialer I/O function status machine figure:
Off-hook: A falling edge to HKS pin
On-hook: A rising edge to HKS pin
H D I
HFI: A high pulse to HFI pin (Hand-free request is generated.)
O n -h o o k
H F I
O ff-h o o k
H a n d -fre e
O n -h o o k
HDI: A low pulse to HDI pin (Hold-line request is generated.)
O ff-h o o k
O n -h o o k
O ff-h o o k
O n -h o o k
H a n d -fre e
H F I
H F I
H D I
Rev. 0.10
H F I
H D I
O ff-h o o k
H D I
O ff-h o o k
H o ld - lin e
H D I
O ff-h o o k
O n -h o o k
O n -h o o k
H o ld - lin e
21
October 1, 2002
Preliminary
HT95L100/10P
Line control function
Register
LINE
(22H)
Label
Bits
R/W
Function
¾
6~0
RO
Unused bit, read as ²0²
LINEC
7
RW
1: Enable the line control function
0: Disable the line control function
The line control function is enabled by the flag LINEC
Conditions
LINEC
Operation Mode
Source to Enable
Line Control Function
1
Normal or Green mode
RTC time out interrupt
1
Sleep mode
Port A wake-up
RTC time out interrupt
1
Idle mode
Port A wake-up
When the line control source is activated, the PO pin will be set to high signal. Clearing LINEC to 0 will terminate the line
control function and drive PO pin outputs low signal.
R T C
In te rru p t
L in e C o n tr o l
C ir c u it
P o r t A W a k e - u p fu n c tio n
L IN E C
P O
= 1
E n a b le /D is a b le
RTC function
Register
RTCC
(24H)
Label
Bits
R/W
Function
¾
6, 4~0
RO
Unused bit, read as ²0²
RTCEN
5
RW
1: Enable RTC function
0: Disable RTC function
RTCTO
7
RW
1: RTC time-out occurs
0: RTC time-out not occurs
The real time clock (RTC) is used to supply a regular internal interrupt. Its time-out period is 1000ms. If the RTC
time-out occurs, the interrupt request flag RTCF and the
RTCTO flag will be set to 1. The interrupt vector for the
RTC is 14H. When the interrupt subroutine is serviced,
the interrupt request flag (RTCF) will be cleared to 0, but
the flag RTCTO remain in its original value. If the
RTCTO flag is not cleared, next RTC time-out interrupt
will occur.
V
R
1 .1 5 V R e fe r e n c e V o lta g e
1
R
2
L B F G
L B IN
L B E N
The battery low threshold is determined by external R1
and R2 resistors.
Low battery detection
1.15=
The phone controller provides a circuit that detects the
LBIN pin voltage level. To enable this detection function, the LBEN should be written as 1. Once this function
is enabled, the detection circuit needs 50ms to be stable.
After that, the user could read the result from LBFG. The
low battery detect function will consume power. For
power saving, write 0 to LBEN if the low battery detection function is unnecessary.
Rev. 0.10
D E T
VDET ´ R2
1.15 ´ (R1+ R2)
® VDET=
R1+ R2
R2
If we want to detect VDET=2.4V
then 2.4V=
22
1.15 ´ (R1+ R2)
® R1=1.087R2
R2
October 1, 2002
Preliminary
HT95L100/10P provides 4 pins to be selected to SEGMENT output pins or I/O pins.
LCD driver
The LCD driver can directly drive an LCD panel with 1/8
duty and 1/4 bias. The frame of this LCD driver is fixed
for 64Hz.
LCD display memory
The phone controller provides an area on embedded
data memory for LCD display. The LCD display memory
are located at bank 1BH and can be read and written to,
only by indirect addressing mode using MP1. When
data is written into the display data area it is automatically read by the LCD driver which then generates the
corresponding LCD driving signals, to turn the display
On or Off, a ²1² or ²0² is written to the corresponding bit
of the display memory, respectively. All of the LCD display memories are with random values after the power
on reset and unchanged after other reset conditions.
LCD driver uses the voltage of the VLCD pin as the
power source. To adjust the view angle, the programmer
can select the real LCD power by the flags VCON0 and
VCON1. The flag LCDON is used to turn On/Off the LCD
display. Note that the VLCD voltage must equal or be
less than VDD.
Segment/Common to I/O selection
For the flexible purpose, some of the LCD SEGMENT
p in s a r e s h a r ed w i t h t h e i nput / out p u t p o r t .
Register
Label
Bits
R/W
LBEN
2
RW
Low battery detection switch
0: disable the low battery detection
1: enable the low battery detection
¾
3,1,0
RO
Unused bit, read as ²0²
LBFG
4
RO
Low battery detection flag
1: LBIN pin voltage is less than 1.25V
0: LBIN pin voltage is not less than 1.25V
LCDC
(2DH)
LCDIO
(28H)
HT95L100/10P
Function
VCON0
VCON1
5
6
RW
LCD contrast adjusting
Bit6,5=00: LCD voltage supply is 0.66´VLCD
Bit6,5=10: LCD voltage supply is 0.82´VLCD
Bit6,5=01: LCD voltage supply is 0.93´VLCD
Bit6,5=11: LCD voltage supply is 1.00´VLCD
LCDON
7
RW
1: Turn on the LCD display
0: Turn off the LCD display
¾
4~0
7~6
RO
Unused bit, read as ²0²
SPE0
5
RW
0: SEG16~SEG19 pins are LCD segment output
1: SEG16~SEG19 pins are PE0~PE3 pins
COM7 to COM0 for HT95L100/10P
Address
Register
Name
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
8CH
SEG0
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
8DH
SEG1
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
¾
¾
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
9EH
SEG18
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
9FH
SEG19
COM7
COM6
COM5
COM4
COM3
COM2
COM1
COM0
Rev. 0.10
23
October 1, 2002
Preliminary
HT95L100/10P
PFD generator
Register
PFDC
(2EH)
Label
Bits
R/W
¾
3~0
RO
Unused bit, read as ²0²
PFDEN
4
RW
1: Enable PFD output
0: Disable PFD output, the MUSIC pin output low level.
PRES0
PRES1
5
6
RW
Bit6, 5=00: Prescaler output= PFD frequency source/1
Bit6, 5=01: Prescaler output= PFD frequency source/2
Bit6, 5=10: Prescaler output= PFD frequency source/4
Bit6, 5=11: Prescaler output= PFD frequency source/8
FPFD
7
RW
1: The PFD frequency source is 3.58MHz/4
0: The PFD frequency source is 32768Hz
¾
7~0
RW
PFD data register
PFDD
(2FH)
Function
The PFD (programmable frequency divider) is implemented in the phone controller. It is composed of two portions: a
prescaler and a general counter.
The prescaler is controlled by the register bits, PRES0 and PRES1. The general counter is programmed by an 8-bit
register PFDD.
The source for this generator can be selected from 3.58MHz/4 or 32768Hz. To enable the PFD output, write 1 to the
PFDEN bit.
The PFDD is inhibited to write while the PFD is disabled. To modify the PFDD contents, the PFD must be enabled.
When the generator is disabled, the PFDD is cleared by hardware.
3 2 7 6 8 H z
3 .5 8 M H z /4
P r e s c a le r
P r e s c a le r
O u tp u t
P F D D
M U S IC
P F D E N
P R E S 1 , P R E S 0
PFD output frequency=
P F D
O u tp u t
Prescaler output
, where N=the value of the PFDD
2 ´ (N + 1)
Mask option table
The following shows many kinds of mask options in the telephone controller. All these options should be defined in order to ensure proper system functions.
Name
Mask Option
WDT
WDT source selection
RC®Select the WDT OSC to be the WDT source.
T1®Select the instruction clock to be the WDT source.
32kHz®Select the external 32768Hz to be the WDT source.
Disable®Disable WDT function.
WDTinstr
This option defines how to clear the WDT by instruction.
One clear instruction®The ²CLR WDT² can clear the WDT.
Two clear instructions®Only when both of the ²CLR WDT1² and ²CLR WDT2² have been
executed, then WDT can be cleared.
Wake-up PA
Port A wake-up selection.
Define the activity of wake-up function.
All port A have the capability to wake-up the chip from a HALT.
This wake-up function is selected per bit.
Pull-high Port A
Pull-high Port B
Pull-high Port E
Pull-high option.
This option determines whether the pull-high resistance is viable or not.
Port A pull-high option is selected per bit.
Port B pull-high option is selected per bit.
Port E pull-high option is selected per nibble.
Rev. 0.10
24
October 1, 2002
Preliminary
HT95L100/10P
Application Circuits
2 2 M W
1 0 0 k W
O ff-h o o k
T ip
O n -h o o k
A 9 2
R in g
3 .3 k W
3 3 0 k W
2 2 0 k W
3 3 k W
1 0 m F
1 N 4 1 4 8
2 .2 k W
1 .5 k W
1 N 4 1 4 8
4 7 k W
1 N 4 1 4 8
1 m F
1 0 0 k W
A 4 2
1 N 4 1 4 8
1 0 0 k W
H a n d fre e
2 2 0 k W
1 5 0 k W
1 m F
B a tte ry
1 .5 ´ 3
= 4 .5 V
1 0 k W
0 .0 2 m F
2 7 0 k W
V
D D
S p e e c h
N e tw o rk
5 .1 V
1 0 0 k W
0 .1 m F
0 .1 m F
1 0 0 m F
V
D D
H F I
P O
H D I
V D D
H K S
H F O
0 .1 m F
D T M F X M U T E
I/O
M U S IC
V
D D
V L C D
1 0 0 k W
R E S
0 .1 m F
H T 9 5 L 1 0 0 /1 0 P
V
D D
L B IN
M E M O R Y
S T O R E
A M
D IA L IN G
H O L D
P M
A B R
M O N
T U E
W E D
T H R
F R I
S A T
S U N
C O M M O N
S E G M E N T
L C D
P a n n e l
I/O
I/O
X 1
X 2
X C
V S S
1 5 k W
1
2
3
K e y 1
K e y 5
K e y 9
4
5
6
K e y 2
K e y 6
K e y 1 0
7
8
9
K e y 3
K e y 7
K e y 1 1
* /T
0
#
K e y 4
K e y 8
K e y 1 2
3 2 7 6 8 H z
3 n F
5 0 n F
K e y M a tr ix
Rev. 0.10
25
October 1, 2002
Preliminary
HT95L100/10P
Instruction Set Summary
Description
Instruction
Cycle
Flag
Affected
Add data memory to ACC
Add ACC to data memory
Add immediate data to ACC
Add data memory to ACC with carry
Add ACC to data memory with carry
Subtract immediate data from ACC
Subtract data memory from ACC
Subtract data memory from ACC with result in data memory
Subtract data memory from ACC with carry
Subtract data memory from ACC with carry and result in data memory
Decimal adjust ACC for addition with result in data memory
1
1(1)
1
1
1(1)
1
1
1(1)
1
1(1)
1(1)
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
Z,C,AC,OV
C
1
1
1
1(1)
1(1)
1(1)
1
1
1
1(1)
1
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Z
Increment data memory with result in ACC
Increment data memory
Decrement data memory with result in ACC
Decrement data memory
1
1(1)
1
1(1)
Z
Z
Z
Z
Rotate data memory right with result in ACC
Rotate data memory right
Rotate data memory right through carry with result in ACC
Rotate data memory right through carry
Rotate data memory left with result in ACC
Rotate data memory left
Rotate data memory left through carry with result in ACC
Rotate data memory left through carry
1
1(1)
1
1(1)
1
1(1)
1
1(1)
None
None
C
C
None
None
C
C
Move data memory to ACC
Move ACC to data memory
Move immediate data to ACC
1
1(1)
1
None
None
None
Clear bit of data memory
Set bit of data memory
1(1)
1(1)
None
None
Mnemonic
Arithmetic
ADD A,[m]
ADDM A,[m]
ADD A,x
ADC A,[m]
ADCM A,[m]
SUB A,x
SUB A,[m]
SUBM A,[m]
SBC A,[m]
SBCM A,[m]
DAA [m]
Logic Operation
AND A,[m]
OR A,[m]
XOR A,[m]
ANDM A,[m]
ORM A,[m]
XORM A,[m]
AND A,x
OR A,x
XOR A,x
CPL [m]
CPLA [m]
AND data memory to ACC
OR data memory to ACC
Exclusive-OR data memory to ACC
AND ACC to data memory
OR ACC to data memory
Exclusive-OR ACC to data memory
AND immediate data to ACC
OR immediate data to ACC
Exclusive-OR immediate data to ACC
Complement data memory
Complement data memory with result in ACC
Increment & Decrement
INCA [m]
INC [m]
DECA [m]
DEC [m]
Rotate
RRA [m]
RR [m]
RRCA [m]
RRC [m]
RLA [m]
RL [m]
RLCA [m]
RLC [m]
Data Move
MOV A,[m]
MOV [m],A
MOV A,x
Bit Operation
CLR [m].i
SET [m].i
Rev. 0.10
26
October 1, 2002
Preliminary
HT95L100/10P
Instruction
Cycle
Flag
Affected
Jump unconditionally
Skip if data memory is zero
Skip if data memory is zero with data movement to ACC
Skip if bit i of data memory is zero
Skip if bit i of data memory is not zero
Skip if increment data memory is zero
Skip if decrement data memory is zero
Skip if increment data memory is zero with result in ACC
Skip if decrement data memory is zero with result in ACC
Subroutine call
Return from subroutine
Return from subroutine and load immediate data to ACC
Return from interrupt
2
1(2)
1(2)
1(2)
1(2)
1(3)
1(3)
1(2)
1(2)
2
2
2
2
None
None
None
None
None
None
None
None
None
None
None
None
None
Read ROM code (current page) to data memory and TBLH
Read ROM code (last page) to data memory and TBLH
2(1)
2(1)
None
None
No operation
Clear data memory
Set data memory
Clear Watchdog Timer
Pre-clear Watchdog Timer
Pre-clear Watchdog Timer
Swap nibbles of data memory
Swap nibbles of data memory with result in ACC
Enter power down mode
1
1(1)
1(1)
1
1
1
1(1)
1
1
None
None
None
TO,PD
TO(4),PD(4)
TO(4),PD(4)
None
None
TO,PD
Mnemonic
Description
Branch
JMP addr
SZ [m]
SZA [m]
SZ [m].i
SNZ [m].i
SIZ [m]
SDZ [m]
SIZA [m]
SDZA [m]
CALL addr
RET
RET A,x
RETI
Table Read
TABRDC [m]
TABRDL [m]
Miscellaneous
NOP
CLR [m]
SET [m]
CLR WDT
CLR WDT1
CLR WDT2
SWAP [m]
SWAPA [m]
HALT
Note:
x: Immediate data
m: Data memory address
A: Accumulator
i: 0~7 number of bits
addr: Program memory address
Ö: Flag is affected
-: Flag is not affected
(1)
: If a loading to the PCL register occurs, the execution cycle of instructions will be delayed for one more cycle
(four system clocks).
(2)
: If a skipping to the next instruction occurs, the execution cycle of instructions will be delayed for one more
cycle (four system clocks). Otherwise the original instruction cycle is unchanged.
(3) (1)
:
(4)
Rev. 0.10
and (2)
: The flags may be affected by the execution status. If the Watchdog Timer is cleared by executing the
CLR WDT1 or CLR WDT2 instruction, the TO and PD are cleared.
Otherwise the TO and PD flags remain unchanged.
27
October 1, 2002
Preliminary
HT95L100/10P
Instruction Definition
ADC A,[m]
Add data memory and carry to the accumulator
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
ADCM A,[m]
Add the accumulator and carry to data memory
Description
The contents of the specified data memory, accumulator and the carry flag are added simultaneously, leaving the result in the specified data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
ADD A,[m]
Add data memory to the accumulator
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the accumulator.
Operation
ACC ¬ ACC+[m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
ADD A,x
Add immediate data to the accumulator
Description
The contents of the accumulator and the specified data are added, leaving the result in the
accumulator.
Operation
ACC ¬ ACC+x
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
ADDM A,[m]
Add the accumulator to the data memory
Description
The contents of the specified data memory and the accumulator are added. The result is
stored in the data memory.
Operation
[m] ¬ ACC+[m]
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
28
October 1, 2002
Preliminary
HT95L100/10P
AND A,[m]
Logical AND accumulator with data memory
Description
Data in the accumulator and the specified data memory perform a bitwise logical_AND operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² [m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
AND A,x
Logical AND immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_AND operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²AND² x
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
ANDM A,[m]
Logical AND data memory with the accumulator
Description
Data in the specified data memory and the accumulator perform a bitwise logical_AND operation. The result is stored in the data memory.
Operation
[m] ¬ ACC ²AND² [m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
CALL addr
Subroutine call
Description
The instruction unconditionally calls a subroutine located at the indicated address. The
program counter increments once to obtain the address of the next instruction, and pushes
this onto the stack. The indicated address is then loaded. Program execution continues
with the instruction at this address.
Operation
Stack ¬ PC+1
PC ¬ addr
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
CLR [m]
Clear data memory
Description
The contents of the specified data memory are cleared to 0.
Operation
[m] ¬ 00H
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
29
October 1, 2002
Preliminary
HT95L100/10P
CLR [m].i
Clear bit of data memory
Description
The bit i of the specified data memory is cleared to 0.
Operation
[m].i ¬ 0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
CLR WDT
Clear Watchdog Timer
Description
The WDT is cleared (clears the WDT). The power down bit (PD) and time-out bit (TO) are
cleared.
Operation
WDT ¬ 00H
PD and TO ¬ 0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
0
0
¾
¾
¾
¾
CLR WDT1
Preclear Watchdog Timer
Description
Together with CLR WDT2, clears the WDT. PD and TO are also cleared. Only execution of
this instruction without the other preclear instruction just sets the indicated flag which implies this instruction has been executed and the TO and PD flags remain unchanged.
Operation
WDT ¬ 00H*
PD and TO ¬ 0*
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
0*
0*
¾
¾
¾
¾
CLR WDT2
Preclear Watchdog Timer
Description
Together with CLR WDT1, clears the WDT. PD and TO are also cleared. Only execution of
this instruction without the other preclear instruction, sets the indicated flag which implies
this instruction has been executed and the TO and PD flags remain unchanged.
Operation
WDT ¬ 00H*
PD and TO ¬ 0*
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
0*
0*
¾
¾
¾
¾
CPL [m]
Complement data memory
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa.
Operation
[m] ¬ [m]
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
30
October 1, 2002
Preliminary
HT95L100/10P
CPLA [m]
Complement data memory and place result in the accumulator
Description
Each bit of the specified data memory is logically complemented (1¢s complement). Bits
which previously contained a 1 are changed to 0 and vice-versa. The complemented result
is stored in the accumulator and the contents of the data memory remain unchanged.
Operation
ACC ¬ [m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
DAA [m]
Decimal-Adjust accumulator for addition
Description
The accumulator value is adjusted to the BCD (Binary Coded Decimal) code. The accumulator is divided into two nibbles. Each nibble is adjusted to the BCD code and an internal
carry (AC1) will be done if the low nibble of the accumulator is greater than 9. The BCD adjustment is done by adding 6 to the original value if the original value is greater than 9 or a
carry (AC or C) is set; otherwise the original value remains unchanged. The result is stored
in the data memory and only the carry flag (C) may be affected.
Operation
If ACC.3~ACC.0 >9 or AC=1
then [m].3~[m].0 ¬ (ACC.3~ACC.0)+6, AC1=AC
else [m].3~[m].0 ¬ (ACC.3~ACC.0), AC1=0
and
If ACC.7~ACC.4+AC1 >9 or C=1
then [m].7~[m].4 ¬ ACC.7~ACC.4+6+AC1,C=1
else [m].7~[m].4 ¬ ACC.7~ACC.4+AC1,C=C
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
Ö
DEC [m]
Decrement data memory
Description
Data in the specified data memory is decremented by 1.
Operation
[m] ¬ [m]-1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
DECA [m]
Decrement data memory and place result in the accumulator
Description
Data in the specified data memory is decremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]-1
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
31
October 1, 2002
Preliminary
HT95L100/10P
HALT
Enter power down mode
Description
This instruction stops program execution and turns off the system clock. The contents of
the RAM and registers are retained. The WDT and prescaler are cleared. The power down
bit (PD) is set and the WDT time-out bit (TO) is cleared.
Operation
PC ¬ PC+1
PD ¬ 1
TO ¬ 0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
0
1
¾
¾
¾
¾
INC [m]
Increment data memory
Description
Data in the specified data memory is incremented by 1
Operation
[m] ¬ [m]+1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
INCA [m]
Increment data memory and place result in the accumulator
Description
Data in the specified data memory is incremented by 1, leaving the result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC ¬ [m]+1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
JMP addr
Directly jump
Description
The program counter are replaced with the directly-specified address unconditionally, and
control is passed to this destination.
Operation
PC ¬addr
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
MOV A,[m]
Move data memory to the accumulator
Description
The contents of the specified data memory are copied to the accumulator.
Operation
ACC ¬ [m]
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
32
October 1, 2002
Preliminary
HT95L100/10P
MOV A,x
Move immediate data to the accumulator
Description
The 8-bit data specified by the code is loaded into the accumulator.
Operation
ACC ¬ x
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
MOV [m],A
Move the accumulator to data memory
Description
The contents of the accumulator are copied to the specified data memory (one of the data
memories).
Operation
[m] ¬ACC
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
NOP
No operation
Description
No operation is performed. Execution continues with the next instruction.
Operation
PC ¬ PC+1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
OR A,[m]
Logical OR accumulator with data memory
Description
Data in the accumulator and the specified data memory (one of the data memories) perform a bitwise logical_OR operation. The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² [m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
OR A,x
Logical OR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical_OR operation.
The result is stored in the accumulator.
Operation
ACC ¬ ACC ²OR² x
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
ORM A,[m]
Logical OR data memory with the accumulator
Description
Data in the data memory (one of the data memories) and the accumulator perform a
bitwise logical_OR operation. The result is stored in the data memory.
Operation
[m] ¬ACC ²OR² [m]
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
33
October 1, 2002
Preliminary
HT95L100/10P
RET
Return from subroutine
Description
The program counter is restored from the stack. This is a 2-cycle instruction.
Operation
PC ¬ Stack
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
RET A,x
Return and place immediate data in the accumulator
Description
The program counter is restored from the stack and the accumulator loaded with the specified 8-bit immediate data.
Operation
PC ¬ Stack
ACC ¬ x
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
RETI
Return from interrupt
Description
The program counter is restored from the stack, and interrupts are enabled by setting the
EMI bit. EMI is the enable master (global) interrupt bit.
Operation
PC ¬ Stack
EMI ¬ 1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
RL [m]
Rotate data memory left
Description
The contents of the specified data memory are rotated 1 bit left with bit 7 rotated into bit 0.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ [m].7
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
RLA [m]
Rotate data memory left and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit left with bit 7 rotated into bit 0, leaving the
rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ [m].7
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
34
October 1, 2002
Preliminary
HT95L100/10P
RLC [m]
Rotate data memory left through carry
Description
The contents of the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the carry bit; the original carry flag is rotated into the bit 0 position.
Operation
[m].(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
[m].0 ¬ C
C ¬ [m].7
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
Ö
RLCA [m]
Rotate left through carry and place result in the accumulator
Description
Data in the specified data memory and the carry flag are rotated 1 bit left. Bit 7 replaces the
carry bit and the original carry flag is rotated into bit 0 position. The rotated result is stored
in the accumulator but the contents of the data memory remain unchanged.
Operation
ACC.(i+1) ¬ [m].i; [m].i:bit i of the data memory (i=0~6)
ACC.0 ¬ C
C ¬ [m].7
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
Ö
RR [m]
Rotate data memory right
Description
The contents of the specified data memory are rotated 1 bit right with bit 0 rotated to bit 7.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ [m].0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
RRA [m]
Rotate right and place result in the accumulator
Description
Data in the specified data memory is rotated 1 bit right with bit 0 rotated into bit 7, leaving
the rotated result in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.(i) ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ [m].0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
RRC [m]
Rotate data memory right through carry
Description
The contents of the specified data memory and the carry flag are together rotated 1 bit
right. Bit 0 replaces the carry bit; the original carry flag is rotated into the bit 7 position.
Operation
[m].i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
[m].7 ¬ C
C ¬ [m].0
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
Ö
35
October 1, 2002
Preliminary
HT95L100/10P
RRCA [m]
Rotate right through carry and place result in the accumulator
Description
Data of the specified data memory and the carry flag are rotated 1 bit right. Bit 0 replaces
the carry bit and the original carry flag is rotated into the bit 7 position. The rotated result is
stored in the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.i ¬ [m].(i+1); [m].i:bit i of the data memory (i=0~6)
ACC.7 ¬ C
C ¬ [m].0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
Ö
SBC A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+[m]+C
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
SBCM A,[m]
Subtract data memory and carry from the accumulator
Description
The contents of the specified data memory and the complement of the carry flag are subtracted from the accumulator, leaving the result in the data memory.
Operation
[m] ¬ ACC+[m]+C
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
SDZ [m]
Skip if decrement data memory is 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. If the result is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, [m] ¬ ([m]-1)
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SDZA [m]
Decrement data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are decremented by 1. If the result is 0, the next
instruction is skipped. The result is stored in the accumulator but the data memory remains
unchanged. If the result is 0, the following instruction, fetched during the current instruction
execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]-1)=0, ACC ¬ ([m]-1)
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
36
October 1, 2002
Preliminary
HT95L100/10P
SET [m]
Set data memory
Description
Each bit of the specified data memory is set to 1.
Operation
[m] ¬ FFH
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SET [m]. i
Set bit of data memory
Description
Bit i of the specified data memory is set to 1.
Operation
[m].i ¬ 1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SIZ [m]
Skip if increment data memory is 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a
dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with
the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, [m] ¬ ([m]+1)
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SIZA [m]
Increment data memory and place result in ACC, skip if 0
Description
The contents of the specified data memory are incremented by 1. If the result is 0, the next
instruction is skipped and the result is stored in the accumulator. The data memory remains unchanged. If the result is 0, the following instruction, fetched during the current instruction execution, is discarded and a dummy cycle is replaced to get the proper
instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if ([m]+1)=0, ACC ¬ ([m]+1)
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SNZ [m].i
Skip if bit i of the data memory is not 0
Description
If bit i of the specified data memory is not 0, the next instruction is skipped. If bit i of the data
memory is not 0, the following instruction, fetched during the current instruction execution,
is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i¹0
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
37
October 1, 2002
Preliminary
HT95L100/10P
SUB A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the accumulator.
Operation
ACC ¬ ACC+[m]+1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
SUBM A,[m]
Subtract data memory from the accumulator
Description
The specified data memory is subtracted from the contents of the accumulator, leaving the
result in the data memory.
Operation
[m] ¬ ACC+[m]+1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
SUB A,x
Subtract immediate data from the accumulator
Description
The immediate data specified by the code is subtracted from the contents of the accumulator, leaving the result in the accumulator.
Operation
ACC ¬ ACC+x+1
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
Ö
Ö
Ö
Ö
SWAP [m]
Swap nibbles within the data memory
Description
The low-order and high-order nibbles of the specified data memory (1 of the data memories) are interchanged.
Operation
[m].3~[m].0 « [m].7~[m].4
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SWAPA [m]
Swap data memory and place result in the accumulator
Description
The low-order and high-order nibbles of the specified data memory are interchanged, writing the result to the accumulator. The contents of the data memory remain unchanged.
Operation
ACC.3~ACC.0 ¬ [m].7~[m].4
ACC.7~ACC.4 ¬ [m].3~[m].0
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
38
October 1, 2002
Preliminary
HT95L100/10P
SZ [m]
Skip if data memory is 0
Description
If the contents of the specified data memory are 0, the following instruction, fetched during
the current instruction execution, is discarded and a dummy cycle is replaced to get the
proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SZA [m]
Move data memory to ACC, skip if 0
Description
The contents of the specified data memory are copied to the accumulator. If the contents is
0, the following instruction, fetched during the current instruction execution, is discarded
and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed
with the next instruction (1 cycle).
Operation
Skip if [m]=0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
SZ [m].i
Skip if bit i of the data memory is 0
Description
If bit i of the specified data memory is 0, the following instruction, fetched during the current
instruction execution, is discarded and a dummy cycle is replaced to get the proper instruction (2 cycles). Otherwise proceed with the next instruction (1 cycle).
Operation
Skip if [m].i=0
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
TABRDC [m]
Move the ROM code (current page) to TBLH and data memory
Description
The low byte of ROM code (current page) addressed by the table pointer (TBLP) is moved
to the specified data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
TABRDL [m]
Move the ROM code (last page) to TBLH and data memory
Description
The low byte of ROM code (last page) addressed by the table pointer (TBLP) is moved to
the data memory and the high byte transferred to TBLH directly.
Operation
[m] ¬ ROM code (low byte)
TBLH ¬ ROM code (high byte)
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
¾
¾
¾
39
October 1, 2002
Preliminary
HT95L100/10P
XOR A,[m]
Logical XOR accumulator with data memory
Description
Data in the accumulator and the indicated data memory perform a bitwise logical Exclusive_OR operation and the result is stored in the accumulator.
Operation
ACC ¬ ACC ²XOR² [m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
XORM A,[m]
Logical XOR data memory with the accumulator
Description
Data in the indicated data memory and the accumulator perform a bitwise logical Exclusive_OR operation. The result is stored in the data memory. The 0 flag is affected.
Operation
[m] ¬ ACC ²XOR² [m]
Affected flag(s)
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
XOR A,x
Logical XOR immediate data to the accumulator
Description
Data in the accumulator and the specified data perform a bitwise logical Exclusive_OR operation. The result is stored in the accumulator. The 0 flag is affected.
Operation
ACC ¬ ACC ²XOR² x
Affected flag(s)
Rev. 0.10
TC2
TC1
TO
PD
OV
Z
AC
C
¾
¾
¾
¾
¾
Ö
¾
¾
40
October 1, 2002
Preliminary
HT95L100/10P
Package Information
64-pin QFP (14´20) outline dimensions
C
H
D
5 1
G
3 3
I
5 2
3 2
F
A
B
E
2 0
6 4
K
a
J
1
Symbol
A
Rev. 0.10
1 9
Dimensions in mm
Min.
Nom.
Max.
18.80
¾
19.20
B
13.90
¾
14.10
C
24.80
¾
25.20
D
19.90
¾
20.10
E
¾
1
¾
F
¾
0.40
¾
G
2.50
¾
3.10
H
¾
¾
3.40
I
¾
0.10
¾
J
1.15
¾
1.45
K
0.10
¾
0.20
a
0°
¾
7°
41
October 1, 2002
Preliminary
HT95L100/10P
Holtek Semiconductor Inc. (Headquarters)
No.3, Creation Rd. II, Science-based Industrial Park, Hsinchu, Taiwan
Tel: 886-3-563-1999
Fax: 886-3-563-1189
http://www.holtek.com.tw
Holtek Semiconductor Inc. (Sales Office)
11F, No.576, Sec.7 Chung Hsiao E. Rd., Taipei, Taiwan
Tel: 886-2-2782-9635
Fax: 886-2-2782-9636
Fax: 886-2-2782-7128 (International sales hotline)
Holtek Semiconductor (Shanghai) Inc.
7th Floor, Building 2, No.889, Yi Shan Rd., Shanghai, China
Tel: 021-6485-5560
Fax: 021-6485-0313
http://www.holtek.com.cn
Holtek Semiconductor (Hong Kong) Ltd.
RM.711, Tower 2, Cheung Sha Wan Plaza, 833 Cheung Sha Wan Rd., Kowloon, Hong Kong
Tel: 852-2-745-8288
Fax: 852-2-742-8657
Holmate Semiconductor, Inc.
48531 Warm Springs Boulevard, Suite 413, Fremont, CA 94539
Tel: 510-252-9880
Fax: 510-252-9885
http://www.holmate.com
Copyright Ó 2002 by HOLTEK SEMICONDUCTOR INC.
The information appearing in this Data Sheet is believed to be accurate at the time of publication. However, Holtek assumes no responsibility arising from the use of the specifications described. The applications mentioned herein are used
solely for the purpose of illustration and Holtek makes no warranty or representation that such applications will be suitable
without further modification, nor recommends the use of its products for application that may present a risk to human life
due to malfunction or otherwise. Holtek reserves the right to alter its products without prior notification. For the most
up-to-date information, please visit our web site at http://www.holtek.com.tw.
Rev. 0.10
42
October 1, 2002