INTERSIL ISL8840AMBEP

ISL8840AMBEP, ISL8841AMBEP, ISL8842AMBEP,
ISL8843AMBEP, ISL8844AMBEP, ISL8845AMBEP
®
Data Sheet
April 2, 2007
Enhanced Plastic (EP) High Performance
Industry Standard Single-Ended Current
Mode PWM Controllers
The ISL884xAMBEP is a high performance drop-in
replacement for the popular 28C4x and 18C4x PWM
controllers suitable for a wide range of power conversion
applications including flyback, forward and boost output
configurations. Its fast signal propagation and output
switching characteristics make this an ideal product for
existing and new designs.
Features include 30V operation, low operating current, 90μA
start-up current, adjustable operating frequency to 2MHz,
and high peak current drive capability with 20ns rise and fall
times.
FN6471.0
Features
• Specifications per DSCC VID V62/07621
• Full Mil-Temp Electrical Performance from -55°C to +125°C
• Controlled Baseline with One Wafer Fabrication Site and
One Assembly/Test Site
• Full Homogenous Lot Processing in Wafer Fab
• No Combination of Wafer Fabrication Lots in Assembly
• Full Traceability Through Assembly and Test by
Date/Trace Code Assignment
• Enhanced Process Change Notification
• Enhanced Obsolescence Management
• Eliminates Need for Up-Screening a COTS Component
RISING UVLO
(V)
MAX. DUTY CYCLE
(%)
ISL8840AMBEP
7.0
100
ISL8841AMBEP
7.0
50
• 35ns Propagation Delay Current Sense to Output
ISL8842AMBEP
14.4
100
• Fast Transient Response with Peak Current Mode Control
ISL8843AMBEP
8.4
100
• 30V Operation
ISL8844AMBEP
14.4
50
• Adjustable Switching Frequency to 2MHz
ISL8845AMBEP
8.4
50
• 20ns Rise and Fall Times with 1nF Output Load
PART NUMBER
• 1A MOSFET Gate Driver
• 90μA Start-up Current, 125μA Maximum
• Trimmed Timing Capacitor Discharge Current for Accurate
Deadtime/Maximum Duty Cycle Control
Device Information
• 1.5MHz Bandwidth Error Amplifier
The specifications for an Extended Plastic (EP) device are
defined in a Vendor Item Drawing (VID), which is controlled
by the Defense Supply Center in Columbus (DSCC). “Hotlinks” to the applicable VID and other supporting application
information are provided on our website.
• Tight Tolerance Voltage Reference Over Line, Load and
Temperature
• ±3% Current Limit Threshold
Applications
Pinout
• Isolated Flyback and Forward Regulators
ISL884XAMBEP
(8 LD SOIC)
TOP VIEW
• Boost Regulators
8 VREF
COMP 1
FB 2
7 VDD
CS 3
6 OUT
RTCT 4
5 GND
1
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 1-888-468-3774 | Intersil (and design) is a registered trademark of Intersil Americas Inc.
Copyright © Intersil Americas Inc. 2007. All Rights Reserved.
All other trademarks mentioned are the property of their respective owners.
ISL8840AMBEP, ISL8841AMBEP, ISL8842AMBEP, ISL8843AMBEP, ISL8844AMBEP, ISL8845AMBEP
Ordering Information
VENDOR PART NUMBER
(Notes 1, 2)
VENDOR ITEM DRAWING
NUMBER
PART MARKING
TEMPERATURE RANGE
(°C)
PACKAGE
PKG.
DWG. #
ISL8840AMBEP
V62/07621-01XB
8840A MBEP
-55 to +125
8 Ld SOIC
M8.15
ISL8841AMBEP
V62/07621-02XB
8841A MBEP
-55 to +125
8 Ld SOIC
M8.15
ISL8842AMBEP
V62/07621-03XB
8842A MBEP
-55 to +125
8 Ld SOIC
M8.15
ISL8843AMBEP
V62/07621-04XB
8843A MBEP
-55 to +125
8 Ld SOIC
M8.15
ISL8844AMBEP
V62/07621-05XB
8844A MBEP
-55 to +125
8 Ld SOIC
M8.15
ISL8845AMBEP
V62/07621-06XB
8845A MBEP
-55 to +125
8 Ld SOIC
M8.15
NOTES:
1. Add -TK suffix for 1,000 piece quantity tape and reel.
2. Devices must be procured to the VENDOR PART NUMBER.
2
FN6471.0
April 2, 2007
ISL8840AMBEP, ISL8841AMBEP, ISL8842AMBEP, ISL8843AMBEP, ISL8844AMBEP, ISL8845AMBEP
Small Outline Plastic Packages (SOIC)
M8.15 (JEDEC MS-012-AA ISSUE C)
N
8 LEAD NARROW BODY SMALL OUTLINE PLASTIC PACKAGE
INDEX
AREA
0.25(0.010) M
H
B M
INCHES
E
SYMBOL
-B-
1
2
3
L
SEATING PLANE
-A-
A
D
h x 45°
-C-
e
A1
B
0.25(0.010) M
C
0.10(0.004)
C A M
MIN
MAX
MIN
MAX
NOTES
A
0.0532
0.0688
1.35
1.75
-
A1
0.0040
0.0098
0.10
0.25
-
B
0.013
0.020
0.33
0.51
9
C
0.0075
0.0098
0.19
0.25
-
D
0.1890
0.1968
4.80
5.00
3
E
0.1497
0.1574
3.80
4.00
4
e
α
B S
0.050 BSC
1.27 BSC
-
H
0.2284
0.2440
5.80
6.20
-
h
0.0099
0.0196
0.25
0.50
5
L
0.016
0.050
0.40
1.27
6
N
α
NOTES:
MILLIMETERS
8
0°
8
8°
0°
7
8°
1. Symbols are defined in the “MO Series Symbol List” in Section 2.2 of
Publication Number 95.
Rev. 1 6/05
2. Dimensioning and tolerancing per ANSI Y14.5M-1982.
3. Dimension “D” does not include mold flash, protrusions or gate burrs.
Mold flash, protrusion and gate burrs shall not exceed 0.15mm (0.006
inch) per side.
4. Dimension “E” does not include interlead flash or protrusions. Interlead flash and protrusions shall not exceed 0.25mm (0.010 inch) per
side.
5. The chamfer on the body is optional. If it is not present, a visual index
feature must be located within the crosshatched area.
6. “L” is the length of terminal for soldering to a substrate.
7. “N” is the number of terminal positions.
8. Terminal numbers are shown for reference only.
9. The lead width “B”, as measured 0.36mm (0.014 inch) or greater
above the seating plane, shall not exceed a maximum value of
0.61mm (0.024 inch).
10. Controlling dimension: MILLIMETER. Converted inch dimensions
are not necessarily exact.
All Intersil U.S. products are manufactured, assembled and tested utilizing ISO9000 quality systems.
Intersil Corporation’s quality certifications can be viewed at www.intersil.com/design/quality
Intersil products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design, software and/or specifications at any time without
notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see www.intersil.com
3
FN6471.0
April 2, 2007