ONSEMI LM317MDTRKG

LM317M
500 mA Adjustable Output,
Positive Voltage Regulator
The LM317M is an adjustable three−terminal positive voltage
regulator capable of supplying in excess of 500 mA over an output
voltage range of 1.2 V to 37 V. This voltage regulator is exceptionally
easy to use and requires only two external resistors to set the output
voltage. Further, it employs internal current limiting, thermal
shutdown and safe area compensation, making it essentially blow−out
proof.
The LM317M serves a wide variety of applications including local,
on−card regulation. This device also makes an especially simple
adjustable switching regulator, a programmable output regulator, or by
connecting a fixed resistor between the adjustment and output, the
LM317M can be used as a precision current regulator.
http://onsemi.com
Heatsink surface
connected to Pin 2
TO−220AB
T SUFFIX
CASE 221AB
Features
•
•
•
•
•
•
•
•
1
Output Current in Excess of 500 mA
Output Adjustable between 1.2 V and 37 V
Internal Thermal Overload Protection
Internal Short Circuit Current Limiting
Output Transistor Safe−Area Compensation
Floating Operation for High Voltage Applications
Eliminates Stocking Many Fixed Voltages
Pb−Free Packages are Available
SOT−223
ST SUFFIX
CASE 318E
Vin
Vout
LM317M
2
3
Vout
1 2
3
Heatsink Surface (shown as terminal 4 in
case outline drawing) is connected to Pin 2.
R1
240
IAdj
*
1
3
4
DPAK
DT SUFFIX
CASE 369C
Vin
2
Adjust
Cin
0.1mF
**
+C
O
1.0mF
R2
PIN ASSIGNMENT
1
Adjust
2
Vout
3
Vin
ORDERING INFORMATION
* = Cin is required if regulator is located an appreciable distance from power supply filter.
** = CO is not needed for stability, however, it does improve transient response.
ǒ
Ǔ
R
Vout + 1.25 V 1 ) 2 ) IAdj R2
R1
See detailed ordering and shipping information in the package
dimensions section on page 10 of this data sheet.
DEVICE MARKING INFORMATION
Since IAdj is controlled to less than 100 mA, the error associated with this
term is negligible in most applications.
See general marking information in the device marking
section on page 11 of this data sheet.
Figure 1. Simplified Application
© Semiconductor Components Industries, LLC, 2006
August, 2006 − Rev. 14
1
Publication Order Number:
LM317M/D
LM317M
MAXIMUM RATINGS (TA = 25°C, unless otherwise noted.)
Symbol
Value
Unit
VI−VO
40
Vdc
PD
qJA
qJC
Internally Limited
70
5.0
°C/W
°C/W
PD
qJA
qJC
Internally Limited
92
5.0
°C/W
°C/W
PD
qJA
qJC
Internally Limited
245
15
°C/W
°C/W
Operating Junction Temperature Range
TJ
−40 to +125
°C
Storage Temperature Range
Tstg
−65 to +150
°C
Rating
Input−Output Voltage Differential
Power Dissipation (Package Limitation) (Note 1)
Plastic Package, T Suffix, Case 221A
TA = 25°C
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
Plastic Package, DT Suffix, Case 369C
TA = 25°C
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
Plastic Package, ST Suffix, Case 318E
TA = 25°C
Thermal Resistance, Junction−to−Air
Thermal Resistance, Junction−to−Case
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
1. Figure 25 provides thermal resistance versus PC board pad size.
ELECTRICAL CHARACTERISTICS (VI − VO = 5.0 V; IO = 0.1 A, TJ = Tlow to Thigh (Note 2), unless otherwise noted.)
Characteristics
Figure
Symbol
Line Regulation (Note 3) (TA = 25°C, 3.0 V ≤ VI − VO ≤ 40 V)
3
Regline
Load Regulation (Note 3)
TA = 25°C, 10 mA ≤ IO ≤ 0.5 A
VO ≤ 5.0 V
VO ≥ 5.0 V
4
Regload
LM317M / LM317MB
Min
Typ
Max
Unit
−
0.01
0.04
%/V
−
−
5.0
0.1
25
0.5
mV
% VO
5
IAdj
−
50
100
mA
Adjustment Pin Current Change
2.5 V ≤ VI − VO ≤ 40 V, 10 mA ≤ IL ≤ 0.5 A, PD ≤ Pmax
3, 4
DIAdj
−
0.2
5.0
mA
Reference Voltage
3.0 V ≤ VI − VO ≤ 40 V, 10 mA ≤ IL ≤ 0.5 A, PD ≤ Pmax
5
Vref
1.200
1.250
1.300
V
Line Regulation (Note 3)
3.0 V ≤ VI−VO ≤ 40 V
3
Regline
−
0.02
0.07
%/V
Load Regulation (Note 3)
10 mA ≤ IO ≤ 0.5 A
VO ≤ 5.0 V
VO ≥ 5.0 V
4
Regload
−
−
20
0.3
70
1.5
mV
% VO
Temperature Stability (Tlow ≤ TJ ≤ Thigh)
5
TS
−
0.7
−
% VO
Minimum Load Current to Maintain Regulation (VI − VO = 40 V)
5
ILmin
−
3.5
10
mA
Maximum Output Current
VI − VO ≤ 15 V, PD ≤ Pmax
VI − VO = 40 V, PD ≤ Pmax, TA = 25°C
5
Imax
0.5
0.15
0.9
0.25
−
−
RMS Noise, % of VO (TA = 25°C, 10 Hz ≤ f ≤ 10 kHz)
−
N
−
0.003
−
Ripple Rejection, VO = 10 V, f = 120 Hz (Note 4)
Without CAdj
CAdj = 10 mF
6
RR
−
66
65
80
−
−
Long−Term Stability, TJ = Thigh (Note 5)
TA= 25°C for End−point Measurements
5
−
0.3
1.0
Adjustment Pin Current
S
A
% VO
dB
%/1.0
kHrs.
2. Tlow to Thigh = 0° to +125°C for LM317M
Tlow to Thigh = − 40° to +125°C for LM317MB.
3. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
4. CAdj, when used, is connected between the adjustment pin and ground.
5. Since Long−Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average
stability from lot−to−lot.
http://onsemi.com
2
LM317M
ELECTRICAL CHARACTERISTICS (VI − VO = 5.0 V; IO = 0.1 A, TJ = Tlow to Thigh (Note 6), unless otherwise noted.)
Characteristics
Figure
Symbol
Line Regulation (Note 7) (TA = 25°C, 3.0 V ≤ VI − VO ≤ 40 V)
3
Regline
Load Regulation (Note 7)
TA = 25°C, 10 mA ≤ IO ≤ 0.5 A
VO ≤ 5.0 V
VO ≥ 5.0 V
4
Regload
Adjustment Pin Current
5
Adjustment Pin Current Change
2.5 V ≤ VI − VO ≤ 40 V, 10 mA ≤ IL ≤ 0.5 A, PD ≤ Pmax
LM317MA / LM317MAB
Min
Typ
Max
Unit
−
0.01
0.04
%/V
−
−
5.0
0.1
25
0.5
mV
% VO
IAdj
−
50
100
mA
3, 4
DIAdj
−
0.2
5.0
mA
Reference Voltage
3.0 V ≤ VI − VO ≤ 40 V, 10 mA ≤ IL ≤ 0.5 A, PD ≤ Pmax
5
Vref
1.225
1.250
1.275
V
Line Regulation (Note 7)
3.0 V ≤ VI−VO ≤ 40 V
3
Regline
−
0.02
0.07
%/V
Load Regulation (Note 7)
10 mA ≤ IO ≤ 0.5 A
VO ≤ 5.0 V
VO ≥ 5.0 V
4
Regload
−
−
20
0.3
70
1.5
mV
% VO
Temperature Stability (Tlow ≤ TJ ≤ Thigh)
5
TS
−
0.7
−
% VO
Minimum Load Current to Maintain Regulation (VI − VO = 40 V)
5
ILmin
−
3.5
10
mA
Maximum Output Current
VI − VO ≤ 15 V, PD ≤ Pmax
VI − VO = 40 V, PD ≤ Pmax, TA = 25°C
5
Imax
0.5
0.15
0.9
0.25
−
−
RMS Noise, % of VO (TA = 25°C, 10 Hz ≤ f ≤ 10 kHz)
−
N
−
−
−
Ripple Rejection, VO = 10 V, f = 120 Hz (Note 8)
Without CAdj
CAdj = 10 mF
6
RR
−
66
65
80
−
−
Long−Term Stability, TJ = Thigh (Note 9)
TA= 25°C for End−point Measurements
5
−
0.3
1.0
S
A
% VO
dB
%/1.0
kHrs.
6. Tlow to Thigh = 0° to +125°C for LM317MA
Tlow to Thigh = − 40° to +125°C for LM317MAB.
7. Load and line regulation are specified at constant junction temperature. Changes in VO due to heating effects must be taken into account
separately. Pulse testing with low duty cycle is used.
8. CAdj, when used, is connected between the adjustment pin and ground.
9. Since Long−Term Stability cannot be measured on each device before shipment, this specification is an engineering estimate of average
stability from lot−to−lot.
http://onsemi.com
3
LM317M
Vin
300
300
300
3.0k
300
70
6.8V
6.8V
350
18k
8.67k
500
130
400
5.1k
200k
6.3V
180
180
2.0k
6.0k
60
10
pF 10
pF
1.25
Vout
2.4k
12.8k
50
Adjust
Figure 2. Representative Schematic Diagram
VCC
VOH − VOL
VOL
Line Regulation (%/V) =
*
VIH
VIL
Vin
Adjust
Cin
*Pulse Testing Required:
1% Duty Cycle is suggested.
0.1mF
VOH
VOL
Vout
LM317M
R1
240
1%
RL
+
CO
IAdj
1.0mF
R2
1%
Figure 3. Line Regulation and DIAdj/Line Test Circuit
http://onsemi.com
4
x 100
LM317M
Load Regulation (mV) = VO (min Load) −VO (max Load)
VO (min Load) − VO (max Load)
Load Regulation (% VO) =
VO (min Load)
Vin
Vin
Vout
LM317M
Adjust
X 100
VO (min Load)
VO (max Load)
IL
R1
RL
(max Load)
240
1%
RL
(min Load)
*
+
Cin
0.1mF
CO
IAdj
1.0mF
R2
1%
*Pulse Testing Required:
1% Duty Cycle is suggested.
Figure 4. Load Regulation and DIAdj/Load Test Circuit
Vin
Vout
LM317M
IL
Adjust
240
1%
R1
VI
IAdj
Cin
Vref
RL
+
CO
0.1mF
1mF
VO
ISET
R2
1%
To Calculate R2:
Vout = ISET R2 + 1.250 V
Assume ISET = 5.25 mA
*Pulse Testing Required:
1% Duty Cycle is suggested.
Figure 5. Standard Test Circuit
24V
Vin
14V
f = 120 Hz
Vout
Adjust
Cin
Vout = 10 V
LM317M
240
1%
R1
D1 *
1N4002
CO
0.1mF
R2
1.65K
1%
**
CAdj
RL
+
1.0mF
+
10mF
*D1 Discharges CAdj if Output is Shorted to Ground.
**CAdj provides an AC ground to the adjust pin.
Figure 6. Ripple Rejection Test Circuit
http://onsemi.com
5
VO
LM317M
0.4
Vin = 45 V
Vout = 5.0 V
IL = 5.0 mA to 40 mA
0.2
RR, RIPPLE REJECTION (dB)
Δ V out , OUTPUT VOLTAGE CHANGE (%)
90
0
−0.2
Vin = 10 V
Vout = 5.0 V
IL = 5.0 mA to 100 mA
−0.4
−0.6
−0.8
−1.0
80
Without CAdj = 10 mF
70
50
−50
−25
0
25
50
75
100 125
TJ, JUNCTION TEMPERATURE (°C)
−50
150
−25
Figure 7. Load Regulation
V in −Vout , INPUT−OUTPUT VOLTAGE
DIFFERENTIAL (V)
Iout , OUTPUT CURRENT (A)
0.80
0.60
TJ = 25°C
0.40
TJ = 125°C
150
2.5
IL = 500 mA
2.0
IL = 100 mA
1.5
1.0
0.5
0
0
10
20
30
40
Vin−Vout, INPUT−OUTPUT VOLTAGE DIFFERENTIAL (V)
50
−50
Figure 9. Current Limit
5.0
100
4.5
90
4.0
3.5
3.0
TJ = 25°C
2.5
TJ = 125°C
2.0
−25
0
25
50
75
100 125
TJ, JUNCTION TEMPERATURE (°C)
150
Figure 10. Dropout Voltage
RR, RIPPLE REJECTION (dB)
IB , QUIESCENT CURRENT (mA)
0
25
50
75
100 125
TJ, JUNCTION TEMPERATURE (°C)
Figure 8. Ripple Rejection
1.0
0.20
Without CAdj
IL = 100 mA
f = 120 Hz
Vout = 10 V
Vin = 14 V to 24 V
60
1.5
1.0
IL = 40 mA
Vin = 5.0 V ± 1.0 VPP
Vout = 1.25 V
80
70
60
50
40
30
20
10
0.5
0
10
20
30
40
Vin−Vout, INPUT−OUTPUT VOLTAGE DIFFERENTIAL (Vdc)
10
Figure 11. Minimum Operating Current
100
1.0 k
10 k
100 k 1.0 M
f, FREQUENCY (Hz)
Figure 12. Ripple Rejection versus Frequency
http://onsemi.com
6
LM317M
1.250
1.240
Vin = 4.2 V
Vout = Vref
IL = 5.0 mA
1.230
1.220
80
IAdj, ADJUSTMENT PIN CURRENT ( μA)
Vref, REFERENCE VOLTAGE (V)
1.260
65
60
55
50
45
40
35
−50
−25
0
25
50
75 100 125
TJ, JUNCTION TEMPERATURE (°C)
Vin = 6.25 V
Vout = Vref
IL = 10 mA
IL = 100 mA
70
150
−50
NOISE VOLTAGE ( μV)
Δ Vout , OUTPUT VOLTAGE CHANGE (%)
75
100
125
150
Bandwidth 100 Hz to 10 kHz
0
−0.2
−0.4
−0.6
8.0
6.0
−0.8
4.0
−50
−25
0
25
50
75 100 125
TJ, JUNCTION TEMPERATURE (°C)
150
−50
Δ Vout , OUTPUT VOLTAGE
DEVIATION (V)
CL = 1.0 mF
3.0
I L , LOAD
CURRENT (A)
1.0
25
50
75
100
1.5
1.0
Vout = 10 V
IL = 50 mA
TJ = 25°C
−1.5
CL = 1.0 mF; CAdj = 10 mF
Vin = 15 V
Vout = 10 V
INL = 50 mA
TJ = 25°C
CL = 0
1.0
Vin
0
10
CL = 0.3 mF; CAdj = 10 mF
−3.0
0.5
20
t, TIME (ms)
150
0
−2.0
−0.5
−1.0
125
2.0
−1.0
0
0
0
Figure 16. Output Noise
1.5
0.5
−25
TJ, JUNCTION TEMPERATURE (°C)
Figure 15. Line Regulation
Δ Vout , OUTPUT VOLTAGE
DEVIATION (V)
50
10
−1.0
Δ Vin , INPUT VOLTAGE
CHANGE (V)
25
Figure 14. Adjustment Pin Current
Vin = 4.25 V to 41.25 V
Vout = Vref
IL = 5.0 mA
0.2
0
TJ, JUNCTION TEMPERATURE (°C)
Figure 13. Temperature Stability
0.4
−25
30
40
1.0
IL
0.5
0
0
10
20
t, TIME (ms)
30
Figure 18. Load Transient Response
Figure 17. Line Transient Response
http://onsemi.com
7
40
LM317M
APPLICATIONS INFORMATION
Basic Circuit Operation
External Capacitors
The LM317M is a three−terminal floating regulator. In
operation, the LM317M develops and maintains a nominal
1.25 V reference (Vref) between its output and adjustment
terminals. This reference voltage is converted to a
programming current (IPROG) by R1 (see Figure 19), and this
constant current flows through R2 to ground. The regulated
output voltage is given by:
A 0.1 mF disc or 1.0 mF tantalum input bypass capacitor
(Cin) is recommended to reduce the sensitivity to input line
impedance.
The adjustment terminal may be bypassed to ground to
improve ripple rejection. This capacitor (CAdj) prevents
ripple from being amplified as the output voltage is
increased. A 10 mF capacitor should improve ripple
rejection about 15 dB at 120 Hz in a 10 V application.
Although the LM317M is stable with no output
capacitance, like any feedback circuit, certain values of
external capacitance can cause excessive ringing. An output
capacitance (CO) in the form of a 1.0 mF tantalum or 25 mF
aluminum electrolytic capacitor on the output swamps this
effect and insures stability.
ǒ
Ǔ
R
Vout + Vref 1 ) 2 ) IAdj R2
R1
Since the current from the terminal (IAdj) represents an
error term in the equation, the LM317M was designed to
control IAdj to less than 100 mA and keep it constant. To do
this, all quiescent operating current is returned to the output
terminal. This imposes the requirement for a minimum load
current. If the load current is less than this minimum, the
output voltage will rise.
Since the LM317M is a floating regulator, it is only the
voltage differential across the circuit which is important to
performance, and operation at high voltages with respect to
ground is possible.
Vin
LM317M
Protection Diodes
When external capacitors are used with any IC regulator
it is sometimes necessary to add protection diodes to prevent
the capacitors from discharging through low current points
into the regulator.
Figure 20 shows the LM317M with the recommended
protection diodes for output voltages in excess of 25 V or
high capacitance values (CO > 25 mF, CAdj > 5.0 mF). Diode
D1 prevents CO from discharging thru the IC during an input
short circuit. Diode D2 protects against capacitor CAdj
discharging through the IC during an output short circuit.
The combination of diodes D1 and D2 prevents CAdj from
discharging through the IC during an input short circuit.
Vout
+
R1
Vref
Adjust
IPROG
Vout
IAdj
D1
R2
1N4002
Vin
Vref = 1.25 V Typical
Vout
LM317M
Vout
+
Figure 19. Basic Circuit Configuration
Cin
R1
D2
Adjust
Load Regulation
The LM317M is capable of providing extremely good
load regulation, but a few precautions are needed to obtain
maximum performance. For best performance, the
programming resistor (R1) should be connected as close to
the regulator as possible to minimize line drops which
effectively appear in series with the reference, thereby
degrading regulation. The ground end of R2 can be returned
near the load ground to provide remote ground sensing and
improve load regulation.
1N4002
R2
CAdj
Figure 20. Voltage Regulator with
Protection Diodes
http://onsemi.com
8
CO
LM317M
+25V
Vout
LM317M
VO
R1
1.25k
Vin
Adjust
D1
D1
1N914
R2
500
* To provide current limiting of IO
to the system ground, the source of
the current limiting diode must be tied to
a negative voltage below −7.25 V.
1N4002
Vin
Vout
+
1.0mF
120
Adjust
1N5314
MPS2222
TTL
Control
720
1.0k
VSS*
Vref
IOmax + IDSS
Minimum Vout = 1.25 V
VO < POV + 1.25 V + VSS
ILmin − IP < IO < 500 mA − IP
As shown O < IO < 495 mA
D1 protects the device during an input short circuit.
Figure 21. Adjustable Current Limiter
Vin
Vout
LM317M
Vin
D2
1N914
Vref
R2 ≥
IDSS
R1 =
IO
Figure 22. 5 V Electronic Shutdown Regulator
Vout
LM317M
Vin
Vout
240
R1
LM317M
Iout
R2
Vout
1N4001
Adjust
IAdj
50k
Adjust
R2
MPS2907
+
Ioutmax =
10mF
Vref
R1 + R2
1.25 V
+ IAdj ^ R + R
1
2
5.0 mA < Iout < 100 mA
R θ JA, THERMAL RESISTANCE, JUNCTION−TO−AIR (° C/W)
Figure 23. Slow Turn−On Regulator
Figure 24. Current Regulator
100
2.4
PD(max) for TA = 50°C
Free Air
Mounted
Vertically
90
80
Minimum
Size Pad
70
60
280
2.0
240
2.0 oz. Copper
L
1.6
200
L
1.2
160
0.8
120
0.4
80
ÎÎÎ
ÎÎÎ
ÎÎÎ
50
2.50
PD(max) for TA = 50°C
Free Air
Mounted
Vertically
1.25
0
10
15
L
0.63
0.42
RqJA
40
5.0
0.83
0.50
RqJA
0
ÎÎÎÎ
ÎÎÎÎ
ÎÎÎÎ
Minimum
Size Pad
2.0 oz. Copper
L
20
25
40
30
0
5.0
10
15
20
25
30
0.35
L, LENGTH OF COPPER (mm)
L, LENGTH OF COPPER (mm)
Figure 25. DPAK Thermal Resistance and Maximum
Power Dissipation versus PCB Copper Length
Figure 26. SOT−223 Thermal Resistance and Maximum
Power Dissipation versus PCB Copper Length
http://onsemi.com
9
LM317M
ORDERING INFORMATION
Output Voltage
Device
Tolerance
Operating Temperature
Range
LM317MABDT
LM317MABDTG
LM317MABDTRK
TJ = −40°C to 125°C
LM317MABDTRKG
LM317MABT
2%
LM317MABTG
LM317MADTRK
TJ = 0°C to 125°C
LM317MADTRKG
LM317MBDT
LM317MBDTG
LM317MBDTRK
LM317MBDTRKG
TJ = −40°C to 125°C
LM317MBSTT3
LM317MBSTT3G
LM317MBT
LM317MBTG
LM317MDT
4%
LM317MDTG
LM317MDTRK
LM317MDTRKG
LM317MSTT3
TJ = 0°C to 125°C
LM317MSTT3G
LM317MT
LM317MTG
Package
Shipping†
DPAK
75 Units / Rail
DPAK
(Pb−Free)
75 Units / Rail
DPAK
2500 / Tape & Reel
DPAK
(Pb−Free)
2500 / Tape & Reel
TO−220
50 Units / Rail
TO−220
(Pb−Free)
50 Units / Rail
DPAK
2500 / Tape & Reel
DPAK
(Pb−Free)
2500 / Tape & Reel
DPAK
75 Units / Rail
DPAK
(Pb−Free)
75 Units / Rail
DPAK
2500 / Tape & Reel
DPAK
(Pb−Free)
2500 / Tape & Reel
SOT−223
4000 / Tape & Reel
SOT−223
(Pb−Free)
4000 / Tape & Reel
TO−220
50 Units / Rail
TO−220
(Pb−Free)
50 Units / Rail
DPAK
75 Units / Rail
DPAK
(Pb−Free)
75 Units / Rail
DPAK
2500 / Tape & Reel
DPAK
(Pb−Free)
2500 / Tape & Reel
SOT−223
4000 / Tape & Reel
SOT−223
(Pb−Free)
4000 / Tape & Reel
TO−220
50 Units / Rail
TO−220
(Pb−Free)
50 Units / Rail
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specification Brochure, BRD8011/D.
http://onsemi.com
10
LM317M
MARKING DIAGRAMS
DPAK
DT SUFFIX
CASE 369C
317ABG
ALYWW
317MAG
ALYWW
317MBG
ALYWW
TO−220
T SUFFIX
CASE 221A
LM
317MABT
AWLYWWG
317MG
ALYWW
SOT−223
ST SUFFIX
CASE 318E
LM
317MBT
AWLYWWG
LM
317MT
AWLYWWG
A
= Assembly Location
L, WL
= Wafer Lot
Y
= Year
WW, W = Work Week
G or G
= Pb−Free Package
(Note: Microdot may be in either location)
http://onsemi.com
11
AYW
317MB G
G
AYW
317M G
G
LM317M
PACKAGE DIMENSIONS
TO−220, SINGLE GAUGE
T SUFFIX
PLASTIC PACKAGE
CASE 221AB−01
ISSUE O
−T−
B
SEATING
PLANE
C
F
T
S
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
3. DIMENSION Z DEFINES A ZONE WHERE ALL
BODY AND LEAD IRREGULARITIES ARE
ALLOWED.
4
DIM
A
B
C
D
F
G
H
J
K
L
N
Q
R
S
T
U
V
Z
A
Q
1 2 3
U
H
K
Z
L
R
V
J
G
D
N
INCHES
MIN
MAX
0.570
0.620
0.380
0.405
0.160
0.190
0.025
0.035
0.142
0.147
0.095
0.105
0.110
0.155
0.018
0.025
0.500
0.562
0.045
0.060
0.190
0.210
0.100
0.120
0.080
0.110
0.020
0.055
0.235
0.255
0.000
0.050
0.045
−−−
−−−
0.080
MILLIMETERS
MIN
MAX
14.48
15.75
9.66
10.28
4.07
4.82
0.64
0.88
3.61
3.73
2.42
2.66
2.80
3.93
0.46
0.64
12.70
14.27
1.15
1.52
4.83
5.33
2.54
3.04
2.04
2.79
0.508
1.39
5.97
6.47
0.00
1.27
1.15
−−−
−−−
2.04
DPAK
DT SUFFIX
PLASTIC PACKAGE
CASE 369C−01
ISSUE O
−T−
C
B
V
NOTES:
1. DIMENSIONING AND TOLERANCING
PER ANSI Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
SEATING
PLANE
E
R
4
Z
A
S
1
2
DIM
A
B
C
D
E
F
G
H
J
K
L
R
S
U
V
Z
3
U
K
F
J
L
H
D
G
2 PL
0.13 (0.005)
M
INCHES
MIN
MAX
0.235 0.245
0.250 0.265
0.086 0.094
0.027 0.035
0.018 0.023
0.037 0.045
0.180 BSC
0.034 0.040
0.018 0.023
0.102 0.114
0.090 BSC
0.180 0.215
0.025 0.040
0.020
−−−
0.035 0.050
0.155
−−−
T
SOLDERING FOOTPRINT*
6.20
0.244
3.0
0.118
2.58
0.101
5.80
0.228
1.6
0.063
6.172
0.243
SCALE 3:1
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
http://onsemi.com
12
mm Ǔ
ǒinches
MILLIMETERS
MIN
MAX
5.97
6.22
6.35
6.73
2.19
2.38
0.69
0.88
0.46
0.58
0.94
1.14
4.58 BSC
0.87
1.01
0.46
0.58
2.60
2.89
2.29 BSC
4.57
5.45
0.63
1.01
0.51
−−−
0.89
1.27
3.93
−−−
LM317M
PACKAGE DIMENSIONS
SOT−223
ST SUFFIX
PLASTIC PACKAGE
CASE 318E−04
ISSUE L
NOTES:
1. DIMENSIONING AND TOLERANCING PER ANSI
Y14.5M, 1982.
2. CONTROLLING DIMENSION: INCH.
D
b1
4
HE
1
2
3
DIM
A
A1
b
b1
c
D
E
e
e1
L1
HE
E
b
e1
e
0.08 (0003)
C
q
A
A1
q
MIN
1.50
0.02
0.60
2.90
0.24
6.30
3.30
2.20
0.85
1.50
6.70
0°
MILLIMETERS
NOM
MAX
1.63
1.75
0.06
0.10
0.75
0.89
3.06
3.20
0.29
0.35
6.50
6.70
3.50
3.70
2.30
2.40
0.94
1.05
1.75
2.00
7.00
7.30
10°
−
MIN
0.060
0.001
0.024
0.115
0.009
0.249
0.130
0.087
0.033
0.060
0.264
0°
INCHES
NOM
0.064
0.002
0.030
0.121
0.012
0.256
0.138
0.091
0.037
0.069
0.276
−
MAX
0.068
0.004
0.035
0.126
0.014
0.263
0.145
0.094
0.041
0.078
0.287
10°
L1
SOLDERING FOOTPRINT*
3.8
0.15
2.0
0.079
2.3
0.091
2.3
0.091
6.3
0.248
2.0
0.079
mm Ǔ
1.5
ǒinches
SCALE 6:1
0.059
*For additional information on our Pb−Free strategy and soldering
details, please download the ON Semiconductor Soldering and
Mounting Techniques Reference Manual, SOLDERRM/D.
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: [email protected]
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
http://onsemi.com
13
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
For additional information, please contact your local
Sales Representative
LM317M/D