MAXIM MAX1878ETC

19-2248; Rev 2; 5/11
KIT
ATION
EVALU
E
L
B
A
AVAIL
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
The MAX1878 dual power supply contains a step-down
and step-up DC-DC converter in a small 12-pin TQFN
package for use in PDAs. The step-down DC-DC converter delivers over 500mA to an output as low as 1.25V for
logic power. The step-up DC-DC converter delivers over
15mA and an output as high as 28V for a liquid crystal display (LCD). With an input voltage from 2.0V to 5.5V the
MAX1878 is intended for use in systems powered by a
2-cell alkaline or 1-cell lithium-ion (Li+) battery.
Fast switching frequency allows the use of small inductors
and capacitors, and the low 19µA typical quiescent current allows high efficiency when the system is in standby
mode. Each output can be independently enabled.
Features
o Evaluation Kit Available to Speed Designs
o Two Output Voltages
Main Output: 1.25V to VIN
LCD Output: Up to 28V
o 2.0V to 5.5V Input Range
o Low 19µA Quiescent Supply Current
o 1µA Shutdown Supply Current
o High Switching Frequency for Small External
Components
o Small 0.75mm High 4mm x 4mm 12-Pin TQFN
Package
The MAX1878 is available in a small 0.75mm high 4mm x
4mm 12-pin TQFN package and requires no external FETs.
The MAX1878 evaluation kit is available to speed designs.
Ordering Information
________________________Applications
Personal Digital Assistants (PDA)
PART
Organizers/Translators
TEMP RANGE
TOP
MARK
MAX1878ETC+
-40°C to +85°C
12-TQFN-EP*
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
MP3 Players
GPS Receivers
IN
LXLCD
AGND
ON
TOP VIEW
10μH
AAGC
Pin Configuration
__________Typical Operating Circuit
INPUT
2.0V TO 5.5V
PINPACKAGE
9
8
7
LCD OUTPUT
UP TO 28V
LXLCD
0.1μF
FBLCD
ONLCD 10
6
FBLCD
5
FB
4
AIN2
AIN1
PGNDLCD 11
AIN2
10μH
MAX1878
LX
FB
ON
MAIN
OFF
LCD
OFF
MAX1878
MAIN OUTPUT
1.25V TO VIN
PGND 12
EP*
+
ON
IN
PGND
2
3
AIN1
1
ONLCD
LX
ON
TQFN
4mm x 4mm
AGND PGNDLCD
*CONNECT EP TO AGND.
________________________________________________________________ Maxim Integrated Products
1
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
MAX1878
General Description
MAX1878
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
ABSOLUTE MAXIMUM RATINGS
FB, FBLCD, AIN1, AIN2, ON, ONLCD to AGND ......-0.3V to +6V
AIN2 to AIN1..........................................................-0.3V to +0.3V
AIN1, AIN2 to IN ....................................................-0.3V to +0.3V
IN to PGND...............................................................-0.3V to +6V
LX to PGND .................................................-0.3V to (VIN + 0.3V)
LXLCD to PGNDLCD..............................................-0.3V to +30V
PGND, PGNDLCD to AGND..................................-0.3V to +0.3V
LX Current .........................................................................800mA
LXLCD Current..................................................................500mA
Continuous Power Dissipation (TA = +70°C)
12-Pin TQFN (derate 24.4mW/°C above +70°C) ...........1.95W
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Soldering Temperature (reflow) .......................................+260°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
PACKAGE THERMAL CHARACTERISTICS (Note 1)
TQFN
Junction-to-Ambient Thermal Resistance (θJA)...............41°C/W
Junction-to-Case Thermal Resistance (θJC)......................6°C/W
Note 1: Package thermal resistances were obtained using the method described in JEDEC specification JESD51-7, using a fourlayer board. For detailed information on package thermal considerations, refer to www.maxim-ic.com/thermal-tutorial.
ELECTRICAL CHARACTERISTICS
(VIN = VAIN = 2.5V, circuit of Figure 1, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
UNITS
5.5
V
GENERAL
Input Voltage Range
Undervoltage Lockout Threshold
VIN, VAIN
VUVLO
2.0
VIN rising
1.92
VIN falling
1.7
Undervoltage Lockout Hysteresis
Quiescent Current
2.0
1.82
100
IAIN1 +
IAIN2
Shutdown Quiescent Current
V
mV
VFB = VFBLCD = 1.30V, VONLCD = 0V,
step-down converter only
19
30
VFB = VFBLCD = 1.30V
24
38
VON = VONLCD = 0V
0
1
µA
VIN
V
µA
MAIN OUTPUT (Step-Down Converter)
Output Voltage Adjustment Range
VMAIN
1.25
FB Regulation Voltage
VFB
VIN = VAIN = 2V
FB Input Bias Current
IFB
VIN = VAIN = 2V
Main Output Current
(Note 2)
IMAIN
VMAIN = 1.8V
TA = +25°C to +85°C
1.225
TA = 0°C to +85°C
1.220
1.250
1.275
1.280
10
VIN = VAIN = 2.5V
250
500
VIN = VAIN = 2.0V
200
350
50
V
nA
mA
Line Regulation
ILOAD = 150mA, VIN = VAIN = 2V to 3V,
FB = GND
1
%
Load Regulation
VIN = VAIN = 2.5V, ILOAD = 10mA to 150mA
1
%
Dropout Voltage
2
VIN = VAIN = 2V, ILOAD = 150mA,
VFB = 0.8V
150
VIN = VAIN = 3V, ILOAD = 150mA,
VFB = 0.8V
100
_______________________________________________________________________________________
mV
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
(VIN = VAIN = 2.5V, circuit of Figure 1, TA = 0°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX
LX Max Duty Cycle
VFB = 0.8V
LX Leakage Current
VON = 0V, VIN = 5.5V
0.1
5
VIN = VAIN = 2V, ILX = 300mA
0.55
0.95
VIN = VAIN = 3V, ILX = 300mA
0.42
0.65
VIN = VAIN = 2V, ILX = 300mA
0.62
0.93
VIN = VAIN = 3V, ILX = 300mA
0.46
0.65
LX P-Channel On-Resistance
LX N-Channel On-Resistance
100
UNITS
%
µA
Ω
Ω
LX Current Limit
330
550
800
mA
Idle Mode Threshold
70
135
220
mA
240
440
740
ns
200
390
670
ns
LX Minimum On-Time
tLXON
LX Minimum Off-Time
tLXOFF
ON Input Low Voltage
2V < VIN < 5.5V
ON Input High Voltage
2V < VIN < 5.5V
0.4
1.3
ON Input Leakage Current
V
V
-1
1
µA
VIN + 1V
28
V
LCD OUTPUT (Step-Up Converter)
LCD Output Voltage Adjust Range
FBLCD Regulation Voltage
VLCD
VFBLCD
LXLCD On-Resistance
VIN = VAIN = 2V
TA = +25°C to +85°C
1.225
TA = 0°C to +85°C
1.220
LCD Output Current
(Note 3)
FBLCD Input Bias Current
5.0
VAIN = VIN = 3V, ILXLCD = 150mA
1.7
3.0
280
440
mA
0
1
µA
140
VAIN = VIN = 2.5V, VLCD = 18V
1.5
7.6
VAIN = VIN = 2V, VLCD = 18V
1.4
6.6
Ω
mA
VAIN = VIN = 2V
10
LCD Line Regulation
VAIN = VIN = 2V to 3V, ILOAD = 5mA,
VLXLCD = 18V
1
%
LCD Load Regulation
VAIN = VIN = 2.5V, ILOAD = 1mA to 5mA,
VLXLCD = 18V
1.3
%
LXLCD Maximum On-Time
LXLCD Minimum Off-Time
IFBLCD
V
2.8
VLXLCD = 28V
ILCD
1.275
1.280
VAIN = VIN = 2V, ILXLCD = 150mA
LXLCD Current Limit
LXLCD Leakage Current
1.250
tLXLCDON
tLXLCDOFF
VFBLCD < 0.9V (soft-start)
ONLCD Input Low Voltage
2V < VAIN = VIN < 5.5V
ONLCD Input High Voltage
2V < VAIN = VIN < 5.5V
ONLCD Input Leakage Current
50
5.1
9.8
17
0.5
1.0
1.7
1.3
2.6
4.4
0.4
1.3
-1
nA
µs
µs
V
V
1
µA
_______________________________________________________________________________________
3
MAX1878
ELECTRICAL CHARACTERISTICS (continued)
MAX1878
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
ELECTRICAL CHARACTERISTICS
(VIN = VAIN = 2.5V, circuit of Figure 1, TA = -40°C to +85°C, unless otherwise noted.) (Note 4)
PARAMETER
SYMBOL
CONDITIONS
MIN
MAX
UNITS
38
µA
GENERAL
Quiescent Current from AIN
IAIN
VFB = VFBLCD = 1.30V
MAIN OUTPUT (Step-Down Converter)
FB Regulation Voltage
VFB
VAIN = VIN = 2V
LX Current Limit
1.212
1.288
V
310
820
mA
LX Minimum On-Time
tLXON
240
740
ns
LX Minimum Off-Time
tLXOFF
200
670
ns
130
450
mA
5.1
17
µs
0.5
1.7
VFBLCD < 0.9V
1.3
4.5
VAIN = VIN = 2V
1.212
1.288
LCD OUTPUT (Step-Up Converter)
LXLCD Current Limit
LXLCD Maximum On-Time
tLXLCDON
LXLCD Minimum Off-Time
tLXLCDOFF
FBLCD Regulation Voltage
VFBLCD
µs
V
Note 2: Main output current is guaranteed by LX current limit, LX on resistance, and LX minimum off-time.
Note 3: LCD output current is guaranteed by LXLCD current limit, LXLCD on-resistance, and LXLCD minimum off-time, starting into
a resistive load.
Note 4: Specifications to TA = -40°C are guaranteed by design and not production tested.
4
_______________________________________________________________________________________
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
EFFICIENCY (%)
80
VIN = 5.0V
VIN = 3.6V
60
VIN = 2.5V
90
80
VIN = 5.0V
70
VIN = 3.6V
60
VIN = 5.0V (22μH)
90
EFFICIENCY (%)
90
100
MAX1878 toc02
VIN = 2.5V
80
70
VIN = 3.6V (15μH)
60
VIN = 2.5V (10μH)
50
50
50
ONLCD =
PGNDLCD
40
1
10
100
1000
ON = PGND
30
0.1
1
10
100
0.01
1000
0.1
1
10
100
LOAD CURRENT (mA)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
STEP-DOWN CONVERTER OUTPUT VOLTAGE
vs. LOAD CURRENT (VMAIN = 1.8V)
STEP-DOWN CONVERTER OUTPUT VOLTAGE
vs. LOAD CURRENT (VMAIN = 1.5V)
STEP-UP CONVERTER OUTPUT VOLTAGE
vs. LOAD CURRENT (VLCD = 18V)
1.83
1.530
VMAIN (V)
1.82
1.81
1.80
VIN = 5.0V
18.6
1.520
18.5
0.1
1
100
1000
18.0
0.1
1
VIN = 2.5V (10μH)
17.9
ONLCD = PGNDLCD
1.495
10
VIN = 3.6V (15μH)
18.3
18.1
VIN = 2.5V
1.500
ONLCD = PGNDLCD
1.77
18.4
18.2
VIN = 3.6V
1.505
VIN = 2.5V
VIN = 5.0V (22μH)
18.7
1.525
1.515
ONLCD = PGNDLCD
18.8
1.510
VIN = 3.6V
1.79
1.78
18.9
VMAIN (V)
VIN = 5.0V
MAX1878 toc05
1.535
MAX1878 toc04
1.84
17.8
10
100
0.01
1000
0.1
1
10
100
LOAD CURRENT (mA)
LOAD CURRENT (mA)
LOAD CURRENT (mA)
NO LOAD SUPPLY CURRENT vs.
INPUT VOLTAGE (VMAIN = 1.8V, VLCD = 18V)
STEP-DOWN CONVERTER SWITCHING
FREQUENCY vs. SUPPLY VOLTAGE
STEP-UP CONVERTER CURRENT LIMIT
vs. INPUT VOLTAGE
100
STEP-UP
80
60
40
1.0
0.8
VMAIN = 1.5V
0.6
VMAIN = 1.8V
0.4
0
0
1
2
3
4
INPUT VOLTAGE (V)
5
6
L2 = 22μH
400
350
300
2
3
4
SUPPLY VOLTAGE (V)
5
L2 = 15μH
250
IMAIN = 150mA
ONLCD = PGNDLCD
STEP-DOWN
0
450
L2 = 10μH
0.2
20
500
MAX1878 toc09
120
1.2
CURRENT LIMIT (mA)
STEP-UP AND STEP-DOWN
SWITCHING FREQUENCY (MHz)
MAX1878 toc07
140
MAX1878 toc08
VMAIN (V)
40
40
0.1
SUPPLY CURRENT (μA)
ONLCD =
PGNDLCD
MAX1878 toc06
EFFICIENCY (%)
100
MAX1878 toc01
100
70
STEP-UP CONVERTER EFFICIENCY
vs. LOAD CURRENT (VLCD = 18V)
STEP-DOWN CONVERTER EFFICIENCY
vs. LOAD CURRENT (VMAIN = 1.5V)
MAX1878 toc03
STEP-DOWN CONVERTER EFFICIENCY
vs. LOAD CURRENT (VMAIN = 1.8V)
200
6
2
3
4
5
SUPPLY VOLTAGE (V)
_______________________________________________________________________________________
6
5
MAX1878
Typical Operating Characteristics
(VIN = VAIN = 2.5V, circuit of Figure 1, TA = +25°C, unless otherwise noted.)
MAX1878
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
Typical Operating Characteristics (continued)
(VIN = VAIN = 2.5V, circuit of Figure 1, TA = +25°C, unless otherwise noted.)
STEP-DOWN LIGHT-LOAD
SWITCHING WAVEFORMS
STEP-UP LIGHT-LOAD
SWITCHING WAVEFORMS
STEP-DOWN HEAVY-LOAD
SWITCHING WAVEFORMS
MAX1878 toc12
MAX1878 toc11
MAX1878 toc10
VMAIN
AC-COUPLED
50mV/div
VMAIN
AC-COUPLED
20mV/div
VOUT
AC-COUPLED
100mV/div
VLX
1V/div
VLX
1V/div
VLXLCD
10V/div
0
0
0
4μs/div
IMAIN = 20mA, VMAIN = +1.8V, VIN = +2.5V, ONLCD = PGNDLCD
1μs/div
IMAIN = 250mA, VMAIN = +1.8V, VIN = +2.5V, ONLCD = PGNDLCD
1μs/div
ILCD = 2mA, VLCD = +18V, VIN = +2.5V, ON = PGND
STEP-DOWN LOAD
TRANSIENT RESPONSE
STEP-UP LOAD
TRANSIENT RESPONSE
STEP-UP HEAVY-LOAD
SWITCHING WAVEFORMS
MAX1878 toc15
MAX1878 toc14
MAX1878 toc13
VOUT
AC-COUPLED
100mV/div
VLXLCD
10V/div
IMAIN
200mA/div
ILCD
2mA/div
VMAIN
AC-COUPLED
100mV/div
VLCD
AC-COUPLED
200mV/div
VLX
2V/div
VLXLCD
10V/div
0
1μs/div
ILCD = 4.5mA, VLCD = +18V, VIN = +2.5V, ON = PGND
10μs/div
IMAIN = 10mA to 250mA, VMAIN = +1.8V,
VIN = +2.5V, ONLCD = PGNDLCD
20μs/div
ILCD = 1mA to 4mA, VLCD = +18V, VIN = +2.5V, ON = PGND
SOFT-START AND SHUTDOWN RESPONSE
LINE TRANSIENT RESPONSE
MAX1878 toc17
MAX1878 toc16
VIN
3V TO 2V
IIN
200mA/div
VLCD
AC-COUPLED
200mV/div
VLCD
10V/div
VMAIN
1V/div
VMAIN
AC-COUPLED
20mV/div
100μs/div
VMAIN = +1.8V, IMAIN = 150mA, VLCD =18.0V, ILCD = 2.5mA
6
VON = VONLCD
5V/div
400μs/div
RMAIN = 5.1Ω, RLCD = 9.09kΩ
_______________________________________________________________________________________
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
PIN
NAME
FUNCTION
1
IN
Step-Down Converter Power Input. Connect IN to the step-down converter power source. Bypass IN to
PGND with a 10µF or greater low-ESR capacitor.
2
LX
Step-Down Converter Switching Node. Connect LX to the step-down converter output LC filter. LX swings
between IN and PGND.
3
AIN1
Analog Input Power 1. AIN1 supplies power to the MAX1878 internal circuitry. Connect AIN1 to the 2.0V to
5.5V input power source. Bypass AIN1 to AGND with a 1µF or greater low-ESR capacitor.
4
AIN2
Analog Input Power 2. Connect AIN1 and AIN2 together as close to the MAX1878 as possible.
5
FB
Step-Down Converter Feedback Input. Connect a resistive voltage-divider from the step-down converter
output voltage to FB. The regulation threshold is 1.25V at FB.
6
FBLCD
LCD Step-Up Converter Feedback Input. Connect a resistive voltage-divider from the step-up converter
output voltage to FBLCD. The regulation threshold is 1.25V at FBLCD.
7
ON
8
AGND
9
LXLCD
LCD Step-Up Converter Switching Node. Connect LXLCD to the step-up converter inductor and rectifier.
10
ONLCD
LCD Step-Up Converter On/Off Input. Drive ONLCD high to turn on the step-up converter. Drive ONLCD
low to turn off the converter. For automatic startup, connect ONLCD to AIN1.
11
PGNDLCD
12
PGND
—
EP
Step-Down Converter On/Off Input. Drive ON high to turn on the step-down converter. Drive ON low to
turn off the converter. For automatic startup, connect ON to AIN1.
Analog (Low-Noise) Ground. The exposed pad and the corner tabs on the TQFN package are internally
connected to analog ground. See the PC Board Layout and Grounding section.
LCD Step-Up Converter Power Ground. PGNDLCD is the source of the step-up converter’s internal
N-channel MOSFET switch. Connect PGNDLCD to PGND as close to the MAX1878 as possible.
Power Ground. PGND is the source of the step-down converter’s internal N-channel MOSFET
synchronous rectifier. Connect PGND to PGNDLCD as close to the MAX1878 as possible.
Exposed Pad. Internally connected to AGND. Connect to a large analog ground (AGND) plane to
maximize thermal performance. Not intended to use as an electrical connection point.
Detailed Description
The MAX1878 step-down and step-up DC-DC converter operates from a 2.0V to 5.5V supply. Consuming
only 19µA of quiescent supply current, the main stepdown converter delivers over 500mA to an output as
low as 1.25V and the LCD step-up converter delivers
over 15mA and an output as high as 28V. The
MAX1878 uses a unique proprietary current-limited
control scheme that provides excellent performance
and high efficiency.
Step-Down Converter Control Scheme
The MAX1878 step-down converter uses a proprietary,
current-limited control scheme to ensure high efficiency,
fast transient response, and physically small external
components. This control scheme is simple: when the
output voltage is out of regulation, the error comparator
begins a switching cycle by turning on the high-side
switch. This switch remains on until the minimum ontime of 440ns expires and the output voltage regulates
or the current-limit threshold is exceeded. Once off, the
high-side switch remains off until the minimum off-time
of 390ns expires and the output voltage falls out of regulation. During this period, the low-side synchronous rectifier turns on and remains on until either the high-side
switch turns on again or the inductor current approaches zero. The internal synchronous rectifier eliminates the
need for an external Schottky diode.
This control scheme allows the MAX1878 step-down
converter to provide excellent performance throughout
the entire load-current range. When delivering light
loads, the high-side switch turns off after the minimum
on-time and after the inductor current reaches the
135mA ideal mode threshold to reduce peak inductor
_______________________________________________________________________________________
7
MAX1878
Pin Description
MAX1878
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
current, resulting in increased efficiency and reduced
output voltage ripple. When delivering medium and
higher output currents, the MAX1878 extends either the
on-time or the off-time, as necessary to maintain regulation, resulting in nearly constant frequency operation
with high efficiency and low output voltage ripple.
enters a high-impedance state and the output remains
connected to the input through the inductor and rectifier holding the output voltage to a diode drop below
VIN. The LCD output capacitance and load determine
the rate at which V LCD decays. Connect ON and
ONLCD to IN for normal operation.
Step-Up Converter Control Scheme
Soft-Start
The MAX1878 step-up converter features a minimum
off-time, current-limited control scheme. The duty cycle
is governed by a pair of one-shots that set a minimum
off-time and a maximum on-time. The switching frequency can be up to 500kHz and depends upon the
load and input voltage. The peak current limit of the
internal N-channel MOSFET is 280mA.
The MAX1878 internal soft-start circuitry limits current
drawn at startup, reducing transients on the input source.
Soft-start is particularly useful for higher impedance input
sources, such as lithium ion and alkaline cells. Step-down
converter soft-start is implemented with current limit. At
startup the step-down converter current limit is set to 25%
of its full current limit. The current limit is increased by
25% every 256 switching cycles until full current limit is
reached. Step-up converter soft-start is implemented with
LXLCD minimum off-time. At startup the LXLCD minimum
off-time is 2.6µs allowing the LCD output voltage to build
up gradually. When the output reaches approximately
80% of its final output voltage the LXLCD minimum offtime is decreased to its final value of 1µs. See Soft-Start
and Shutdown Response in the Typical Operating
Characteristics section.
On/Off Control
Pulling ON low places the MAX1878 step-down converter in shutdown mode and reduces step-down converter supply current to less than 1µA. In shutdown, the
internal switching MOSFETs and synchronous rectifier
turn off and LX goes high impedance.
Pulling ONLCD low places the MAX1878 step-up converter in shutdown mode and reduces step-up converter supply current to less than 1µA. In shutdown, LXLCD
L2
10μH*
VIN
2.0V TO 3.3V*
D1
LCD OUTPUT
UP TO 28V
C1
10μF
TWO SERIES
ALKALINE CELLS
1
IN
LXLCD
R5
10Ω
FBLCD
3
4
C2
1μF
ON
OFF
ON
LCD
OFF
7
10
C5
5pF
R3
3.6MΩ
C3
0.1μF
6
R4
270kΩ
AIN1
AIN2
L1
10μH
MAX1878
MAIN
9
LX
2
R6
2MΩ
ON
FB
ONLCD
PGND
12
MAIN OUTPUT
1.25V TO VIN
C6
20pF
R1
28kΩ
C4
22μF
5
R2
63.4kΩ
AGND PGNDLCD
8
11
*FOR INPUT VOLTAGES GREATER THAN 3.3V USE A HIGHER
VALUE INDUCTOR L2. SEE INDUCTOR SELECTION
Figure 1. MAX1878 Standard Application Circuit
8
_______________________________________________________________________________________
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
FBLCD (Figure 1). Select an R4 from 30kΩ to 300kΩ.
Calculate R3 with the following equation:
Setting the Output Voltage
Set the MAX1878 step-down converter output voltage
by connecting a resistive voltage-divider from VMAIN to
FB (Figure 1). Select an R2 from 30kΩ to 300kΩ.
Calculate R1 with the following equation:
R1 =
R2 xR6(VMAIN − VFB )
VFB (R6 + R2) − VMAIN xR2
where VFB = 1.25V, R6 = 2MΩ and VMAIN may range
from 1.25V to VIN.
Set the MAX1878 step-up converter output voltage by
connecting a resistive voltage-divider from V LCD to
⎛ V
⎞
R3 = R4 ⎜ LCD − 1⎟
⎝ VFBLCD ⎠
where VFBLCD = 1.25V and VLCD may range from (VIN
+ 1V) to 28V.
The FB and FBLCD input bias currents are a maximum
of 50nA. These small bias currents allow for large-value
feedback resistors that improve light-load efficiency. For
less than 1% output voltage error due to bias current,
feedback resistors should be chosen such that the current through R2 is 100 times greater than IFB and the
current through R4 is 100 times greater than IFBLCD.
VIN
1
IN
3
AIN1
4
AIN2
MAX1878
LXLCD 9
VLCD
CURRENT
LIMIT
N
P
2 LX
VMAIN
CONTROL
LOGIC
CURRENT
LIMIT
N
TIMERS
FBLCD 6
5 FB
SOFTSTART
ON
OFF
ONLCD 10
7 ON
PGND
12
AGND
8
ON
OFF
PGNDLCD
11
Figure 2. Simplified Functional Diagram
_______________________________________________________________________________________
9
MAX1878
Design Procedure
MAX1878
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
Inductor Selection
The MAX1878 is optimized to use a 10µH inductor over
the entire operating range. Smaller inductance values
typically offer smaller physical size for a given series
resistance or saturation current. Circuits using larger
inductance values may startup at lower input voltages
and exhibit less ripple, but also provide reduced output
power. This occurs when the inductance is sufficiently
large to prevent the maximum current limit from being
reached before the maximum on-time expires. The
inductor’s saturation current rating should be greater
than the peak switching current. However, it is generally
acceptable to bias the inductor into saturation by as
much as 20%, although this will slightly reduce efficiency. Choose a low DC-resistance inductor to improve efficiency. For the above reasons choose the step-up
converter inductor in the range of 10µH to 33µH
depending on the input voltage (4µH per volt of VIN).
Step-Up Converter Diode Selection
The high maximum switching frequency of 500kHz
requires a high-speed rectifier such as the 1N4148. To
maintain high efficiency, the average current rating of
the diode should be greater than the peak switching
current. Choose a reverse breakdown voltage greater
than the output voltage. A Schottky diode is not recommended as the lower forward voltage does little to
improve efficiency whereas the higher reverse leakage
current decreases efficiency.
Input Bypass Capacitors
Bypass VIN with a 10µF low-ESR surface-mount ceramic capacitor to PGND and PGNDLCD as close to the IC
as possible. This input bypass capacitor reduces peak
currents and noise at the input voltage source. Connect
AIN1 and AIN2 together and bypass with a low-ESR
1µF surface-mount ceramic capacitor to AGND. A low
resistance (10Ω) from IN to AIN1 and AIN2 creates a
lowpass RC filter and provides low-noise analog input
power to the MAX1878.
Output Filter Capacitors
The MAX1878 is a voltage mode converter and requires
ripple at FB and FBLCD for stable regulation. For most
applications, bypass VLCD with a 0.1µF small ceramic
surface-mount capacitor to PGNDLCD. For small
10
ceramic capacitors, the output ripple voltage is dominated by the capacitance value. If tantalum or electrolytic capacitors are used, the higher ESR increases the
output ripple voltage. Decreasing the ESR reduces the
output ripple voltage and the peak-to-peak transient
voltage. Surface-mount capacitors are generally preferred because they lack the inductance and resistance
of their through-hole equivalents. Bypass VMAIN with a
10µF to 47µF tantalum capacitor to PGND. Choose a
capacitor with 200mΩ to 300mΩ ESR to provide stable
switching while minimizing output ripple. A 22µF filter
capacitor works well for most applications.
Ripple Regulation
For proper switching control the ripple at FB and FBLCD
must be greater than 25mV. Use R6 and C6 as shown in
Figure 1 to inject ripple into FB. To insure sufficient ripple
on FBLCD, connect C5 as shown in Figure 1.
PC Board Layout and Grounding
High switching frequencies make PC board layout a
very important part of design. Good design minimizes
excessive EMI on the feedback paths and voltage gradients in the ground plane, both of which can result in
instability or regulation errors. Connect the inductors,
input filter capacitors, and output filter capacitors as
close to the device as possible, and keep their traces
short, direct, and wide. The external voltage-feedback
networks should be very close to the feedback pins,
within 0.2 inches (5mm). Keep noisy traces, such as LX
and LXLCD, away from the voltage feedback networks;
also keep them separate, using grounded copper.
The exposed backside pad and corner tabs of the
TQFN package are internally connected to analog
ground. For heat dissipation, connect the exposed
backside pad to a large analog ground plane, preferably on a surface of the board that receives good airflow. Connect all power grounds and all analog
grounds to separate ground planes in a star ground
configuration. Connect the analog ground plane and
the power ground plane together at a single point. The
MAX1878 evaluation kit data sheet includes a proper
PC board layout and routing scheme.
______________________________________________________________________________________
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
EXPOSED PAD CONNECTED TO AGND
PROCESS: BiCMOS
For the latest package outline information and land patterns
(footprints), go to www.maxim-ic.com/packages. Note that a
"+", "#", or "-" in the package code indicates RoHS status only.
Package drawings may show a different suffix character, but
the drawing pertains to the package regardless of RoHS status.
PACKAGE
TYPE
12 TQFN
PACKAGE
CODE
OUTLINE
NO.
LAND
PATTERN NO.
T1244+4
21-0139
90-0068
______________________________________________________________________________________
11
MAX1878
Package Information
Chip Information
MAX1878
Dual-Output Step-Down and LCD Step-Up
Power Supply for PDAs
Revision History
REVISION
NUMBER
REVISION
DATE
2
5/11
DESCRIPTION
Replaced QFN package with TQFN package and added exposed pad to
Pin Description section
PAGES
CHANGED
1, 7
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600
© 2011 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.