19-1505; Rev 0; 7/99 2.5Ω, Dual, SPST, CMOS Analog Switches Features The MAX4667/MAX4668/MAX4669 dual analog switches feature low on-resistance of 2.5Ω max. On-resistance is matched between switches to 0.5Ω max and is flat (0.5Ω max) over the specified signal range. Each switch can handle Rail-to-Rail® analog signals. The off-leakage current is only 5nA max at +85°C. These analog switches are ideal in low-distortion applications and are the preferred solution over mechanical relays in automatic test equipment or applications where current switching is required. They have low power requirements, use less board space, and are more reliable than mechanical relays. The MAX4667 has two normally closed (NC) switches, the MAX4668 has two normally open (NO) switches, and the MAX4669 has one NC and one NO switch that guarantee break-before-make operation. These switches operate from a +4.5V to +36V single supply or from ±4.5V to ±20V dual supplies. All digital inputs have +0.8V and +2.4V logic thresholds, ensuring TTL/CMOS-logic compatibility when using ±15V supplies or a single +12V supply. ♦ Low On-Resistance (2.5Ω max) ♦ Guaranteed RON Match Between Channels (0.5Ω max) ♦ Guaranteed RON Flatness over Specified Signal Range (0.5Ω max) ♦ Guaranteed Break-Before-Make (MAX4669) ♦ Rail-to-Rail Signal Handling ♦ Guaranteed ESD Protection >2kV per Method 3015.7 ♦ +4.5V to +36V Single-Supply Operation ±4.5V to ±20V Dual-Supply Operation ♦ TTL/CMOS-Compatible Control Inputs Ordering Information PART MAX4667CSE MAX4667CPE MAX4667ESE MAX4667EPE Applications Reed Relay Replacement PBX, PABX Systems Test Equipment Audio-Signal Routing Communication Systems Avionics TEMP. RANGE 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C PIN-PACKAGE 16 Narrow SO 16 Plastic DIP 16 Narrow SO 16 Plastic DIP Ordering Information continued at end of data sheet. ______________________Pin Configurations/Functional Diagrams/Truth Tables TOP VIEW N.C. 1 16 NC1 N.C. 1 16 NO1 N.C. 1 16 NO1 IN1 2 15 N.C. IN1 2 15 N.C. IN1 2 15 N.C. N.C. 3 14 COM1 N.C. 3 14 COM1 N.C. 3 14 COM1 V- 4 13 V+ V- 4 13 V+ V- 4 13 V+ GND 5 12 VL GND 5 12 VL GND 5 12 VL N.C. 6 11 COM2 N.C. 6 11 COM2 N.C. 6 11 COM2 IN2 7 10 N.C. IN2 7 10 N.C. IN2 7 10 N.C. N.C. 8 9 NC2 N.C. 8 9 NO2 N.C. 8 9 NC1 MAX4667 MAX4668 SO/DIP SO/DIP MAX4667 MAX4669 SO/DIP MAX4668 MAX4669 LOGIC SWITCH LOGIC SWITCH LOGIC SWITCH 1 SWITCH 2 0 1 ON OFF 0 1 OFF ON 0 1 OFF ON ON OFF Rail-to-Rail is a registered trademark of Nippon Motorola, Ltd. ________________________________________________________________ Maxim Integrated Products 1 For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800. For small orders, phone 1-800-835-8769. MAX4667/MAX4668/MAX4669 General Description MAX4667/MAX4668/MAX4669 2.5Ω, Dual, SPST, CMOS Analog Switches ABSOLUTE MAXIMUM RATINGS V+ to GND ..............................................................-0.3V to +44V V- to GND ...............................................................+0.3V to -44V V+ to V-...................................................................-0.3V to +44V VL to GND ........................................(GND - 0.3V) to (V+ + 0.3V) All Other Pins to GND (Note 1) .............(V- - 0.3V) to (V+ + 0.3V) Continuous Current (COM_, NO_, NC_).........................±100mA Peak Current (COM_, NO_, NC_) (pulsed at 1ms, 10% duty cycle)................................ ±300mA Continuous Power Dissipation (TA = +70°C) Narrow SO (derate 8.70mW/°C above +70°C) .............696mW Plastic DIP (derate 10.53mW/°C above +70°C) ...........842mW Operating Temperature Ranges MAX466_C_E ......................................................0°C to +70°C MAX466_E_E ...................................................-40°C to +85 °C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10sec) .............................+300°C Note 1: Signals on NC_, NO_, COM_, or IN_ exceeding V+ or V- will be clamped by internal diodes. Limit the forward diode current to maximum current rating. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS—Dual Supplies (V+ = +15V, V- = -15V, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS V+ V ANALOG SWITCH Input Voltage Range (Note 3) COM_ to NO_, COM_ to NC_ On-Resistance VCOM_, VNO_, VNC_ V- RON ICOM_ = 10mA, VNO_ or VNC_ = ±10V COM_ to NO_, COM_ to NC_ On-Resistance Match Between Channels (Notes 3, 4) ∆RON ICOM_ = 10mA; VNO_ or VNC_= -5V, 0, 5V COM_ to NO_, COM_ to NC_ On-Resistance Flatness (Notes 3, 5) RFLAT(ON) Off-Leakage Current (NO_ or NC_) (Note 6) INO_, INC_ VCOM_ = ±10V, VNO_ or VNC_ = +–10V COM_ Off-Leakage Current (Note 6) ICOM_(OFF) VCOM_ = ±10V, VNO_ or VNC_ = +–10V COM_ On-Leakage Current (Note 6) ICOM_(ON) VCOM_ = ±10V, VNO_ or VNC_= ±10V or floating ICOM_ = 10mA, VNO_ or VNC_ = ±10V TA = +25°C 1.6 TA = TMIN to TMAX 3 TA = +25°C 0.05 TA = TMIN to TMAX 0.1 TA = TMIN to TMAX TA = +25°C TA = +25°C 0.4 Ω Ω 0.5 TA = +25°C TA = TMIN to TMAX 2.5 0.4 Ω 0.5 -0.5 0.01 -5 -0.5 TA = TMIN to TMAX -5 TA = +25°C -1 TA = TMIN to TMAX -20 0.5 5 0.01 0.5 5 0.02 nA nA 1 nA 20 LOGIC INPUT Input Current with Input Voltage High IIN_H IN_ = 2.4V, all others = 0.8V -0.5 0.001 0.5 µA Input Current with Input Voltage Low IIN_L IN_ = 0.8V, all others = 2.4V -0.5 0.001 0.5 µA Logic Input Voltage High VIN_H Logic Input Voltage Low VIN_L 2 2.4 _______________________________________________________________________________________ V 0.8 V 2.5Ω, Dual, SPST, CMOS Analog Switches (V+ = +15V, V- = -15V, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS ±20.0 V POWER SUPPLY Power-Supply Range ±4.5 TA = +25°C Positive Supply Current I+ TA = +25°C I- 0.001 0.5 5 -0.5 5 0.001 0.5 µA TA = +25°C IGND -0.5 5 VIN = 0 or 5V TA = TMIN to TMAX Ground Current 5 µA TA = +25°C IL 0.5 VIN = 0 or 5V TA = TMIN to TMAX Logic Supply Current 0.001 µA TA = TMIN to TMAX Negative Supply Current -0.5 VIN = 0 or 5V 5 -0.5 5 0.001 0.5 VIN = 0 or 5V µA TA = TMIN to TMAX 5 5 SWITCH DYNAMIC CHARACTERISTICS TA = +25°C Turn-On Time tON VCOM_ = ±10V, Figure 2 TA = TMIN to TMAX Turn-Off Time tOFF VCOM_ = ±10V, Figure 2 TA = TMIN to TMAX Break-Before-Make Time Delay (MAX4669) Charge Injection 275 400 TA = +25°C VCOM = 10V Q 130 90 175 300 5 ns ns 30 ns CL = 1.0nF, VGEN = 0, RGEN = 0, Figure 3 450 pC Off-Isolation (Note 7) VISO RL = 50Ω, CL = 5pF, f = 1MHz, Figure 4 -60 dB Crosstalk (Note 8) VCT RL = 50Ω, CL = 5pF, f = 1MHz, Figure 5 -66 dB 65 pF NC_ or NO_ Capacitance COFF f = 1MHz, Figure 6 COM_ Off-Capacitance CCOM f = 1MHz, Figure 6 65 pF On-Capacitance CCOM f = 1MHz, Figure 7 290 pF _______________________________________________________________________________________ 3 MAX4667/MAX4668/MAX4669 ELECTRICAL CHARACTERISTICS—Dual Supplies (continued) MAX4667/MAX4668/MAX4669 2.5Ω, Dual, SPST, CMOS Analog Switches ELECTRICAL CHARACTERISTICS—Single Supply (V+ = +12V, V- = 0, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS V+ V ANALOG SWITCH Input Voltage Range (Note 3) COM_ to NO_, COM_ to NC_ On-Resistance VCOM_, VNO_, VNC_ 0 RON ICOM_ = 10mA; VNO_ or VNC_ = 10V COM_ to NO_, COM_ to NC_ On-Resistance Match Between Channels (Notes 3, 4) ∆RON ICOM_ = 10mA; VNO_ or VNC_ = 10V COM_ to NO_, COM_ to NC_ On-Resistance Flatness (Note 5) RFLAT(ON) Off-Leakage Current (NO_ or NC_) (Notes 6, 9) INO_, INC_ COM Off-Leakage Current (Notes 6, 9) ICOM_(OFF) COM On-Leakage Current (Notes 6, 9) ICOM_(ON) ICOM_ = 10mA; VNO_ or VNC_ = 3V, 6V, 0V VCOM_ = 1V, 10V; VNO_ or VNC_ = 1V, 10V VCOM_ = 10V, 1V; VNO_ or VNC_ = 1V, 10V VCOM_ = 1V, 10V; VNO_ or VNC_= 1V, 10V, or floating TA = +25°C 3 TA = TMIN to TMAX 5 TA = +25°C 0.05 TA = TMIN to TMAX 0.4 Ω Ω 0.5 TA = +25°C 0.05 TA = TMIN to TMAX TA = +25°C 4 0.5 Ω 0.5 -0.5 0.01 0.5 nA TA = TMIN to TMAX TA = +25°C -5 -0.5 5 0.01 0.5 nA TA = TMIN to TMAX -5 TA = +25°C -1 TA = TMIN to TMAX -20 5 0.01 1 nA 20 LOGIC INPUT Input Current with Input Voltage High IIN_H IN_ = 2.4V, all others = 0.8V -0.5 0.001 0.5 µA Input Current with Input Voltage Low IIN_L IN_ = 0.8V, all others = 2.4V -0.5 0.001 0.5 µA Logic Input Voltage High VIN_H Logic Input Voltage Low VIN_L 4 2.4 _______________________________________________________________________________________ V 0.8 V 2.5Ω, Dual, SPST, CMOS Analog Switches (V+ = +12V, V- = 0, VL = +5V, VIN_H = +2.4V, VIN_L = +0.8V, TA = TMIN to TMAX, unless otherwise noted. Typical values are at TA = +25°C.) (Note 2) PARAMETER SYMBOL CONDITIONS MIN TYP MAX UNITS 36.0 V POWER SUPPLY Power-Supply Range 4.5 Positive Supply Current I+ VIN = 0 or 5V Logic Supply Current IL VIN = 0 or 5V IGND VIN = 0 or 5V Ground Current TA = +25°C TA = TMIN to TMAX TA = +25°C TA = TMIN to TMAX TA = +25°C TA = TMIN to TMAX -0.5 0.001 -5 -0.5 5 0.001 -5 -0.5 0.5 0.5 5 0.001 -5 0.5 5 µA µA µA SWITCH DYNAMIC CHARACTERISTICS Turn-On Time (Note 3) tON VCOM_ = 10V, Figure 2 Turn-Off Time (Note 3) tOFF VCOM_ = 10V, Figure 2 Break-Before-Make Time Delay (MAX4669) Charge Injection VCT 200 100 TA = TMIN to TMAX CL = 1.0nF, VGEN = 0, RGEN = 0, Figure 3 400 500 TA = +25°C VCOM = 10V Q Crosstalk (Note 8) TA = +25°C TA = TMIN to TMAX 200 300 10 ns ns ns 50 pC RL = 50Ω, CL = 5pF, f = 1MHz, Figure 5 -66 dB NC or NO Capacitance COFF f = 1MHz, Figure 6, TA = +25°C 105 pF COM Off-Capacitance CCOM f = 1MHz, Figure 6, TA = +25°C 105 pF On-Capacitance CCOM f = 1MHz, Figure 7, TA = +25°C 185 pF Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in this data sheet. Note 3: Guaranteed by design. Note 4: ∆RON = RON(MAX) - RON(MIN). Note 5: Flatness is defined as the difference between the maximum and minimum values of on-resistance as measured over the specified analog signal range. Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C. Note 7: Off-isolation = 20log10 [VCOM / (VNC or VNO)], VCOM = output, VNC or VNO = input to off switch. Note 8: Between any two switches. Note 9: Leakage testing at single supply is guaranteed by testing with dual supplies. _______________________________________________________________________________________ 5 MAX4667/MAX4668/MAX4669 ELECTRICAL CHARACTERISTICS—Single Supply (continued) Typical Operating Characteristics (TA = +25°C, unless otherwise noted.) 2.2 RON (Ω) 1.8 1.6 V+, V- = ±20V V+, V- = ±15V 8 TA = +25°C 6 5 4 -15 -10 -5 0 5 10 15 20 -10 -5 0 5 10 0 15 6 9 12 15 18 21 24 27 30 33 36 VCOM (V) ON-RESISTANCE vs. VCOM AND TEMPERATURE (SINGLE SUPPLY) ON/OFF-LEAKAGE CURRENT vs. TEMPERATURE CHARGE INJECTION vs. VCOM 2.5 300 ON-LEAKAGE 10 -100 -200 1m 2 4 6 8 10 12 -300 -40 -20 0 20 40 60 80 100 -20 -15 -10 -5 0 5 10 15 VCOM (V) TEMPERATURE (°C) VCOM (V) ON/OFF TIMES vs. VCOM (DUAL SUPPLIES) ON/OFF TIMES vs. VCOM (SINGLE SUPPLY) ON/OFF TIMES vs. SUPPLY VOLTAGE (DUAL SUPPLIES) 140 300 tON 250 120 150 MAX4667/68/69-08 RL = 100Ω CL = 35pF tON 160 MAX4667/68/69-07 180 140 130 80 tON, tOFF (ns) tON, tOFF (ns) tOFF 150 100 60 RL = 100Ω CL = 35pF V+ = 12V V- = GND tOFF 50 20 0 -6 -4 -2 0 2 VCOM (V) 4 6 8 10 tON 110 tOFF 100 90 80 40 0 20 120 200 100 -10 -8 V+ = 12V V- = GND 100 0 0.01 0 200 OFF-LEAKAGE 1 TA = -40°C 1.5 400 100 0.1 2.0 V+ = 15V V- = -15V 500 Q (pC) 3.0 MAX4667/68/69-06 1k LEAKAGE (pA) TA = +85°C V+ = 15V V- = -15V 10k 600 MAX4667/68/69-05 100k MAX4667/68/69-04 V+ = 12V ICOM = 10mA TA = +25°C 6 3 VCOM (V) 3.5 RON (Ω) 0 -15 VCOM (V) 4.5 4.0 V+ = 36V 1 TA = -40°C 1.0 -20 V+ = 24V 2 1.2 1.0 V+ = 12V 3 1.4 1.5 V+ = 5V 7 MAX4667/68/69-09 RON (Ω) 2.0 TA = +85°C 2.0 9 MAX4667/68/69-03 2.4 3.0 2.5 V+, V- = ±15V ICOM = 10mA ON-RESISTANCE (Ω) V+, V- = ±5V 2.6 MAX4667/68/69-02 ICOM = 10mA MAX4667/68/69-01 4.0 3.5 ON-RESISTANCE vs. VCOM (SINGLE SUPPLY) ON-RESISTANCE vs. VCOM AND TEMPERATURE (DUAL SUPPLIES) ON-RESISTANCE vs. VCOM (DUAL SUPPLIES) tON, tOFF (ns) MAX4667/MAX4668/MAX4669 2.5Ω, Dual, SPST, CMOS Analog Switches 0 2 4 6 8 VCOM (V) 10 12 14 70 RL = 100Ω CL = 35pF VCOM = 10V 60 50 10 11 12 13 14 15 16 17 18 19 20 V+ = -V- (V) _______________________________________________________________________________________ 2.5Ω, Dual, SPST, CMOS Analog Switches ON/OFF TIMES vs. TEMPERATURE (DUAL SUPPLIES) 160 140 tON 250 200 tON, tOFF (ns) tON, tOFF (ns) 300 tOFF 100 80 60 tON RL = 100Ω CL = 35pF VCOM = 10V V+ = 15V V- = -15V 40 100 20 tOFF 0 0 5 10 15 20 25 30 35 150 100 tOFF 50 -40 -20 0 20 40 60 80 100 -60 -40 -20 TEMPERATURE (°C) 0 MAX4667/68/69-13 V+ = 15V V- = -15V ON-LOSS -10 -20 40 60 80 100 ON-PHASE -30 LOSS (dB) I+ I- 10 20 FREQUENCY RESPONSE 10k 100 0 TEMPERATURE (°C) SUPPLY CURRENT vs. TEMPERATURE 1k tON 200 0 -60 40 V+ (V) I+, -I- (pA) 0 RL = 100Ω CL = 35pF VCOM = 5V V+ = 12V V- = GND 300 120 400 tON, tOFF (ns) 350 MAX4667/68/69-14 500 180 MAX4667/68/69-11 RL = 100Ω CL = 35pF VCOM = 5V MAX4667/68/69-10 600 ON/OFF TIMES vs. TEMPERATURE (SINGLE SUPPLY) MAX4667/68/69-12 ON/OFF TIMES vs. SUPPLY VOLTAGE (SINGLE SUPPLY) 1 -40 V+ = 15V V- = -15V -50 -60 CROSSTALK -70 0.1 -80 0.01 -100 OFF-ISOLATION -90 -60 -40 -20 0 20 40 TEMPERATURE (°C) 60 80 100 50Ω IN AND OUT 0.01 0.1 1 10 100 FREQUENCY (MHz) _______________________________________________________________________________________ 7 MAX4667/MAX4668/MAX4669 Typical Operating Characteristics (continued) (TA = +25°C, unless otherwise noted.) MAX4667/MAX4668/MAX4669 2.5Ω, Dual, SPST, CMOS Analog Switches Pin Description PIN NAME MAX4668 MAX4669 1, 3, 6, 8, 10, 15 1, 3, 6, 8, 10, 15 1, 3, 6, 8, 10, 15 N.C. 2, 7 2, 7 2, 7 IN2, IN2 4 4 4 V- 5 5 5 GND 12 12 12 VL Logic Supply Input 13 13 13 V+ Positive Analog Supply Voltage Input 14, 11 14, 11 14, 11 COM1, COM2 16, 9 — — NC1, NC2 Analog Switch, Normally Closed Terminals — 16, 9 — NO1, NO2 Analog Switch, Normally Open Terminals — — 9 NC1 Analog Switch, Normally Closed Terminal — — 16 NO1 Analog Switch, Normally Open Terminal Applications Information Overvoltage Protection Proper power-supply sequencing is recommended for all CMOS devices. Do not exceed the absolute maximum ratings because stresses beyond the listed ratings can cause permanent damage to the devices. Always sequence V+ on first, then V-, followed by the logic inputs, NO, or COM. If power-supply sequencing is not possible, add two small signal diodes (D1, D2) in series with supply pins (Figure 1). Adding diodes reduces the analog signal range to one diode drop below V+ and one diode drop above V-, but does not affect the devices’ low switch resistance and low leakage characteristics. Device operation is unchanged, and the difference between V+ and V- should not exceed 44V. These protection diodes are not recommended when using a single supply. Off-Isolation at High Frequencies With the N.C. pins connected to GND, the high-frequency on-response of these parts extends from DC to above 100MHz with a typical loss of -2dB. When the switch is turned off, however, it behaves like a capacitor, and off-isolation decreases with increasing frequency. (Above 300MHz, the switch actually passes more signal turned off than turned on.) This effect is more pronounced with higher source and load impedances. 8 FUNCTION MAX4667 No Connection. Not internally connected. Connect to GND as low impedance to improve on/off-isolation. Logic-Control Digital Inputs Negative Analog Supply Voltage Input. Connect to GND for single-supply operation. Ground Analog Switch, Common Terminals Above 5MHz, circuit-board layout becomes critical and it becomes difficult to characterize the response of the switch independent of the circuit. The graphs shown in the Typical Operating Characteristics were taken using a 50Ω source and load connected with BNC connectors to a circuit board deemed “average”; that is, designed with isolation in mind, but not using stripline or other special RF circuit techniques. For critical applications above 5MHz, use the MAX440, MAX441, and MAX442, which are fully characterized up to 160MHz. +15V MAX4667 MAX4668 MAX4669 D1 V+ * * * * NO_/NC_ COM_ VD2 -15V * INTERNAL PROTECTION DIODES Figure 1. Overvoltage Protection Using External Blocking Diodes _______________________________________________________________________________________ 2.5Ω, Dual, SPST, CMOS Analog Switches MAX4667 MAX4668 MAX4669 +5V +15V VL COM_ SWITCH V COM_ INPUT VO RL 100Ω IN_ GND LOGIC INPUT SWITCH OUTPUT V+ NO_ OR NC_ LOGIC INPUT 50% 0V CL 35pF t OFF VO V- 0 SWITCH OUTPUT -15V 0V 0.9V0 0.9V0 t ON REPEAT TEST FOR EACH SWITCH. FOR LOAD CONDITIONS, SEE ELECTRICAL CHARACTERISTICS. CL INCLUDES FIXTURE AND STRAY CAPACITANCE. RL VO = VCOM RL + RON ( t r < 20ns t f < 20ns +3V LOGIC INPUT WAVEFORMS INVERTED FOR SWITCHES THAT HAVE THE OPPOSITE LOGIC SENSE. ) Figure 2. Switching-Time Test Circuit MAX4667 MAX4668 MAX4669 RGEN +5V +15V VL V+ ∆VO VO COM NC OR NO VO VIN CL V GEN GND IN OFF V- -15V VIN = +3V VIN OFF ON ON OFF OFF Q = (∆V O )(C L ) VIN DEPENDS ON SWITCH CONFIGURATION; INPUT POLARITY DETERMINED BY SENSE OF SWITCH. Figure 3. Charge-Injection Test Circuit _______________________________________________________________________________________ 9 MAX4667/MAX4668/MAX4669 Test Circuits/Timing Diagrams MAX4667/MAX4668/MAX4669 2.5Ω, Dual, SPST, CMOS Analog Switches Test Circuits/Timing Diagrams (continued) C +15V +5V V+ VL SIGNAL GENERATOR 0dBm MAX4667 MAX4668 MAX4669 SIGNAL GENERATOR 0dBm COM 0 OR 2.4V IN COM ANALYZER C NC_ OR NO_ 0 or 2.4V +5V V+ VL COM1 V- 50Ω N01 0 OR 2.4V COM2 GND NC V- C RL C RL MAX4667 MAX4668 MAX4669 IN2 IN1 N02 ANALYZER GND +15V -15V -15V Figure 4. Off-Isolation Test Circuit C Figure 5. Crosstalk Test Circuit +15V +5V V+ VL COM MAX4667 MAX4668 MAX4669 C +15V +5V V+ VL COM MAX4667 MAX4668 MAX4669 CAPACITANCE METER IN IN 0 OR 2.4V CAPACITANCE METER NC OR NO NC OR NO f = 1MHz GND V- -15V Figure 6. Switch Off-Capacitance Test Circuit 10 0 OR 2.4V f = 1MHz C GND V- -15V Figure 7. Switch On-Capacitance Test Circuit ______________________________________________________________________________________ C 2.5Ω, Dual, SPST, CMOS Analog Switches TEMP. RANGE 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C 0°C to +70°C 0°C to +70°C -40°C to +85°C -40°C to +85°C PIN-PACKAGE TRANSISTOR COUNT: 108 16 Narrow SO 16 Plastic DIP 16 Narrow SO 16 Plastic DIP 16 Narrow SO 16 Plastic DIP 16 Narrow SO 16 Plastic DIP Package Information SOICN.EPS PART MAX4668CSE MAX4668CPE MAX4668ESE MAX4668EPE MAX4669CSE MAX4669CPE MAX4669ESE MAX4669EPE Chip Information ______________________________________________________________________________________ 11 MAX4667/MAX4668/MAX4669 Ordering Information (continued) 2.5Ω, Dual, SPST, CMOS Analog Switches PDIPN.EPS MAX4667/MAX4668/MAX4669 Package Information (continued) Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 1999 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products.