74VCXH16245 LOW VOLTAGE CMOS 16-BIT BUS TRANSCEIVER (3-STATE) WITH 3.6V TOLERANT INPUTS AND OUTPUTS ■ ■ ■ ■ ■ ■ ■ ■ ■ 3.6V TOLERANT INPUTS AND OUTPUTS HIGH SPEED : tPD = 2.5 ns (MAX.) at VCC = 3.0 to 3.6V tPD = 3.2 ns (MAX.) at VCC = 2.3 to 2.7V POWER DOWN PROTECTION ON INPUTS AND OUTPUTS SYMMETRICAL OUTPUT IMPEDANCE: |IOH| = IOL = 24mA (MIN) at VCC = 3.0V |IOH| = IOL = 18mA (MIN) at VCC = 2.3V OPERATING VOLTAGE RANGE: VCC (OPR) = 1.8V to 3.6V PIN AND FUNCTION COMPATIBLE WITH 74 SERIES H16245 BUS HOLD PROVIDED ON BOTH SIDES LATCH-UP PERFORMANCE EXCEEDS 300mA (JESD 17) ESD PERFORMANCE: HBM > 2000V (MIL STD 883 method 3015); MM > 200V TSSOP ORDER CODES PACKAGE TSSOP TUBE T&R 74VCXH16245TTR PIN CONNECTION DESCRIPTION The 74VCXH16245 is a low voltage CMOS 16 BIT BUS TRANSCEIVER (3-STATE) fabricated with sub-micron silicon gate and five-layer metal wiring C2MOS technology. It is ideal for low power and very high speed 2.3 to 3.6V applications; it can be interfaced to 3.6V signal environment for both inputs and outputs. This IC is intended for two-way asynchronous communication between data buses; the direction of data transmission is determined by DIR input. The two enable inputs nG can be used to disable the device so that the buses are effectively isolated. Bus hold on data inputs is provided in order to eliminate the need for external pull-up or pull-down resistor. All inputs and outputs are equipped with protection circuits against static discharge, giving them 2KV ESD immunity and transient excess voltage. All floating bus terminals during High Z State must be held HIGH or LOW. October 2002 1/10 74VCXH16245 INPUT AND OUTPUT EQUIVALENT CIRCUIT PIN DESCRIPTION PIN No IEC LOGIC SYMBOLS SYMBOL 1 2, 3, 5, 6, 8, 9, 11, 12 13, 14, 16, 17, 19, 20, 22, 23 24 25 36, 35, 33, 32, 30, 29, 27, 26 47, 46, 44, 43, 41, 40, 38, 38 48 4, 10, 15, 21, 28, 34, 39, 45 NAME AND FUNCTION 1DIR Directional Control 1B1 to 1B8 Data Inputs/Outputs 2B1 to 2B8 Data Inputs/Outputs 2DIR Directional Control 2G Output Enable Input 2A1 to 2A8 Data Inputs/Outputs 1A1 to 1A8 Data Inputs/Outputs 1G 7, 18, 31, 42 Output Enable Input GND Ground (0V) VCC Positive Supply Voltage TRUTH TABLE INPUTS FUNCTION G DIR L L H L H X X : Don‘t Care Z : High Impedance 2/10 A BUS B BUS OUTPUT INPUT INPUT OUTPUT Z Z OUTPUT Yn A=B B=A Z 74VCXH16245 ABSOLUTE MAXIMUM RATINGS Symbol VCC Parameter Value Unit Supply Voltage -0.5 to +4.6 V VI DC Input Voltage -0.5 to +4.6 V VO DC Output Voltage (OFF State) VO DC Output Voltage (High or Low State) (note 1) -0.5 to +4.6 V -0.5 to VCC + 0.5 V IIK DC Input Diode Current - 50 mA IOK DC Output Diode Current (note 2) - 50 mA IO DC Output Current ± 50 mA ICC or IGND DC V CC or Ground Current per Supply Pin Power Dissipation PD Tstg Storage Temperature TL Lead Temperature (10 sec) ± 100 mA 400 mW -65 to +150 °C 300 °C Absolute Maximum Ratings are those values beyond which damage to the device may occur. Functional operation under these conditions is not implied 1) IO absolute maximum rating must be observed 2) VO < GND, VO > VCC RECOMMENDED OPERATING CONDITIONS Symbol Value Unit Supply Voltage 2.3 to 3.6 V VI Input Voltage -0.3 to 3.6 V VO Output Voltage (OFF State) 0 to 3.6 V VO Output Voltage (High or Low State) 0 to VCC V ± 24 mA ± 18 mA VCC I OH, IOL I OH, IOL Top dt/dv Parameter High or Low Level Output Current (VCC = 3.0 to 3.6V) High or Low Level Output Current (VCC = 2.3 to 2.7V) Operating Temperature Input Rise and Fall Time (note 1) -55 to 125 °C 0 to 10 ns/V 1) VIN from 0.8V to 2V at VCC = 3.0V 3/10 74VCXH16245 DC SPECIFICATIONS (2.7V < VCC < 3.6V unless otherwise specified) Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage II(HOLD) Ioff IOZ ICC ∆ICC 4/10 Input Leakage Current Input Hold Current Min. Max. 2.0 -55 to 125 °C Min. 2.0 V 0.8 0.8 2.7 to 3.6 IO=-100 µA VCC-0.2 VCC-0.2 2.7 I O=-12 mA 2.2 2.2 I O=-18 mA 2.4 2.4 I O=-24 mA 2.2 2.2 V 2.7 to 3.6 IO=100 µA 0.2 0.2 2.7 I O=12 mA 0.4 0.4 I O=18 mA 0.4 0.4 I O=24 mA 0.55 0.55 VI = 0 or7 3.6V ±5 ±5 2.7 to 3.6 3.0 Unit Max. 2.7 to 3.6 3.0 II -40 to 85 °C VCC (V) 3.0 VOL Value VI = 0.8V 75 75 VI = 2V -75 -75 V µA µA 3.6 V I = 0 to 3.6V ± 500 ± 500 0 VI or VO = 0 to 3.6V 10 10 µA 2.7 to 3.6 VI = VIH or VIL VO = 0 to 3.6V ± 10 ± 10 µA V I = VCC or GND 20 20 VI or VO = VCC to 3.6V VIH = VCC - 0.6V ± 20 ± 20 750 750 Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current ICC incr. per Input 2.7 to 3.6 2.7 to 3.6 µA µA 74VCXH16245 DC SPECIFICATIONS (2.3V < VCC < 2.7V unless otherwise specified) Test Condition Symbol VIH VIL VOH Parameter High Level Input Voltage Low Level Input Voltage High Level Output Voltage Low Level Output Voltage II(HOLD) Ioff IOZ ICC Input Leakage Current Input Hold Current Power Off Leakage Current High Impedance Output Leakage Current Quiescent Supply Current Min. Max. 1.6 2.3 to 2.7 2.3 to 2.7 2.3 to 2.7 VOLV V OHV Unit Max. 1.6 V 0.7 IO=-100 µA VCC-0.2 VCC-0.2 IO=-6 mA 2.0 2.0 I O=-12 mA 1.8 1.8 I O=-18 mA 1.7 1.7 V IO=100 µA 0.2 0.2 I O=12 mA 0.4 0.4 I O=18 mA 0.6 0.6 V I = 0 to 3.6V ±5 ±5 2.3 VI = 0.7V 45 45 VI = 1.7V -45 -45 V µA µA 0 VI or VO = 0 to 3.6V 10 10 µA 2.3 to 2.7 VI = VIH or VIL VO = 0 to 3.6V ± 10 ± 10 µA V I = VCC or GND 20 20 VI or VO = VCC to 3.6V ± 20 ± 20 2.3 to 2.7 Parameter Dynamic Low Voltage Quiet Output (note 1, 3) Dynamic Low Voltage Quiet Output (note 1, 3) Dynamic High Voltage Quiet Output (note 2, 3) 2.5 2.5 3.3 2.5 3.3 Value TA = 25 °C V CC (V) 3.3 µA (Ta = 25°C, Input tr = tf = 2.0ns, CL = 30pF, RL = 500Ω) Test Conditi on VOLP Min. 0.7 DYNAMIC SWITCHING CHARACTERISTICS Symbol -55 to 125 °C 2.3 to 2.7 2.3 II -40 to 85 °C VCC (V) 2.3 VOL Value Min. Typ. VIL = 0V VIH = VCC 0.6 VIL = 0V VIH = VCC -0.6 VIL = 0V VIH = VCC 0.8 -0.8 1.9 2.2 Unit Max. V V V 1) Number of outputs defined as ”n”. Measured with ”n-1” outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the LOW state. 2) Number of outputs defined as ”n”. Measured with ”n-1” outputs switching from HIGH to LOW or LOW to HIGH. The remaining output is measured in the HIGH state. 3) Parameters guaranteed by design. 5/10 74VCXH16245 AC ELECTRICAL CHARACTERISTICS (CL = 30pF, RL = 500Ω, Input tr = tf = 2.0ns) Test Condition Symbol Parameter tPLH tPHL Propagation Delay Time tPZL tPZH Output Enable Time tPLZ tPHZ Output Disable Time tOSLH tOSHL Output To Output Skew Time (note1, 2) -40 to 85 °C VCC (V) 2.3 3.0 2.3 3.0 2.3 3.0 2.3 3.0 Value to 2.7 to 3.6 to 2.7 to 3.6 to 2.7 to 3.6 to 2.7 to 3.6 -55 to 125 °C Min. Max. Min. Max. 1.0 0.8 1.0 0.8 1.0 0.8 3.2 2.5 4.9 3.8 4.2 3.7 0.5 0.5 1.0 0.8 1.0 0.8 1.0 0.8 3.8 3.1 5.6 4.4 4.8 4.3 0.5 0.5 Unit ns ns ns ns 1) Skew is defined as the absolute value of the difference between the actual propagation delay for any two outputs of the same device switching in the same direction, either HIGH or LOW (tOSLH = | tPLHm - tPLHn|, tOSHL = | tPHLm - tPHLn|) 2) Parameter guaranteed by design CAPACITIVE CHARACTERISTICS Test Condition Symbol Parameter TA = 25 °C VCC (V) Min. Typ. Unit Max. 2.5 or 3.3 VIN = 0 or VCC 4 pF COUT Output Capacitance 2.5 or 3.3 VIN = 0 or VCC 8 pF C PD Power Dissipation Capacitance (note 1) 2.5 or 3.3 fIN = 10MHz VIN = 0 or VCC 36 pF CIN Input Capacitance Value 1) CPD is defined as the value of the IC’s internal equivalent capacitance which is calculated from the operating current consumption without load. (Refer to Test Circuit). Average operating current can be obtained by the following equation. ICC(opr) = CPD x VCC x fIN + ICC/16 (per circuit) 6/10 74VCXH16245 TEST CIRCUIT TEST SWITCH tPLH, tPHL Open tPZL, tPLZ (VCC = 3.0 to 3.6V) 6V tPZL, tPLZ (V CC = 2.3 to 2.7V) tPZH, tPHZ 2V CC GND CL = 30 pF or equivalent (includes jig and probe capacitance) RL = R1 = 500Ω or equivalent RT = ZOUT of pulse generator (typically 50Ω) WAVEFORM SYMBOL VALUES VCC Symbol VIH 3.0 to3.6V 2.3 to 2.7V 2.7V VCC VM 1.5V VCC/2 VX VOL + 0.3V VOL + 0.15V VY VOH - 0.3V VOH - 0.15V 7/10 74VCXH16245 WAVEFORM 1: PROPAGATION DELAYS (f=1MHz; 50% duty cycle) WAVEFORM 2: OUTPUT ENABLE AND DISABLE TIME (f=1MHz; 50% duty cycle) 8/10 74VCXH16245 TSSOP48 MECHANICAL DATA mm. inch DIM. MIN. TYP MAX. A MIN. TYP. 1.2 A1 0.05 0.047 0.15 A2 MAX. 0.002 0.006 0.9 0.035 b 0.17 0.27 0.0067 0.011 c 0.09 0.20 0.0035 0.0079 D 12.4 12.6 0.408 0.496 E 8.1 BSC E1 6.0 0.318 BSC 6.2 e 0.236 0.5 BSC 0.244 0.0197 BSC K 0° 8° 0° 8° L 0.50 0.75 0.020 0.030 A A2 A1 b K e L E c D E1 PIN 1 IDENTIFICATION 1 7065588C 9/10 74VCXH16245 Information furnished is believed to be accurate and reliable. However, STMicroelectronics assumes no responsibility for the consequences of use of such information nor for any infringement of patents or other rights of third parties which may result from its use. No license is granted by implication or otherwise under any patent or patent rights of STMicroelectronics. Specifications mentioned in this publication are subject to change without notice. This publication supersedes and replaces all information previously supplied. STMicroelectronics products are not authorized for use as critical components in life support devices or systems without express written approval of STMicroelectronics. The ST logo is a registered trademark of STMicroelectronics 2002 STMicroelectronics - Printed in Italy - All Rights Reserved STMicroelectronics GROUP OF COMPANIES Australia - Brazil - Canada - China - Finland - France - Germany - Hong Kong - India - Israel - Italy - Japan - Malaysia - Malta - Morocco Singapore - Spain - Sweden - Switzerland - United Kingdom - United States. http://www.st.com 10/10