AD AD8324JRQ

3.3 V Upstream
Cable Line Driver
AD8324
FEATURES
FUNCTIONAL BLOCK DIAGRAM
BYP
VIN+
VOUT+
DIFF
OR SINGLE
INPUT
AMP
VIN–
VERNIER
ATTENUATION
CORE
OUTPUT
STAGE
VOUT–
ZIN (SINGLE) = 550Ω
ZIN (DIFF) = 1100Ω
ZOUT DIFF =
75Ω
8
DECODE
8
AD8324
POWERDOWN LOGIC
RAMP
DATA LATCH
8
APPLICATIONS
GND
DOCSIS 2.0 and Euro-DOCSIS cable modems
CATV set-top boxes
CATV telephony modems
Coaxial and twisted pair line drivers
–40
GENERAL DESCRIPTION
–50
DATEN
DATA CLK
04339-0-001
SHIFT
REGISTER
TXEN
SLEEP
Figure 1. Functional Block Diagram
1
DISTORTION (dBc)
The AD8324 is a low cost amplifier designed for coaxial line
driving. The features and specifications make the AD8324
ideally suited for DOCSIS 2.0 and Euro-DOCSIS applications.
The gain of the AD8324 is digitally controlled. An 8-bit serial
word determines the desired output gain over a 59 dB range,
resulting in gain changes of 1 dB/LSB.
VOUT = 61dBmV @ DEC 60
THIRD HARMONIC
–60
VOUT = 61dBmV @ DEC 60
SECOND HARMONIC
–70
The AD8324 accepts a differential or single-ended input signal.
The output is specified for driving a 75 Ω load through a 1:1
transformer.
04339-0-002
Supports DOCSIS 2.0 and Euro-DOCSIS standards for
reverse path transmission systems
Gain programmable in 1 dB steps over a 59 dB range
Low distortion at 61 dBmV output:
–59 dBc SFDR at 21 MHz
–54 dBc SFDR at 65 MHz
Output noise level @ minimum gain 1.3 nV/√Hz
Maintains 75 Ω output impedance in TX-enable and
Transmit-disable condition
Upper bandwidth: 100 MHz (full gain range)
3.3 V supply operation
Supports SPI® interfaces
–80
5
15
25
35
45
FREQUENCY (MHz)
55
65
Figure 2. Worst Harmonic Distortion vs. Frequency
Distortion performance of –54 dBc is achieved with an output
level up to 61 dBmV at 65 MHz bandwidth.
This device has a sleep mode function that reduces the quiescent current to 30 μA and a full power-down function that
reduces power-down current to 2.5 mA.
The AD8324 is packaged in a low cost 20-lead LFCSP package
and a 20-lead QSOP package. The AD8324 operates from a
single 3.3 V supply.
1
Patent pending.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
© 2005 Analog Devices, Inc. All rights reserved.
AD8324
TABLE OF CONTENTS
Specifications..................................................................................... 3
RAMP Pin and BYP Pin Features ............................................ 11
Logic Inputs (TTL/CMOS Compatible Logic)......................... 4
Power Saving Features ............................................................... 12
Timing Requirements .................................................................. 4
Distortion, Adjacent Channel Power, and DOCSIS .............. 12
Absolute Maximum Ratings............................................................ 5
Utilizing Diplex Filters............................................................... 12
Thermal Resistance ...................................................................... 5
Noise and DOCSIS..................................................................... 12
ESD Caution.................................................................................. 5
Evaluation Board Features and Operation.............................. 13
Pin Configurations and Functional Descriptions ........................ 6
Differential Signal Source ......................................................... 13
Typical Performance Characteristics ............................................. 7
Differential Signal from Single-Ended Source ....................... 13
Applications..................................................................................... 10
Single-Ended Source.................................................................. 13
General Applications.................................................................. 10
Overshoot on PC Printer Ports ................................................ 14
Circuit Description..................................................................... 10
Installing Visual Basic Control Software................................. 14
Gain Programming for the AD8324 ........................................ 10
Running AD8324 Software ....................................................... 14
Input Bias, Impedance, and Termination................................ 10
Controlling Gain/Attenuation of the AD8324 ....................... 14
Output Bias, Impedance, and Termination............................. 10
Transmit Enable and Sleep Mode............................................. 14
Power Supply............................................................................... 11
Memory Functions..................................................................... 14
Signal Integrity Layout Considerations ................................... 11
Outline Dimensions ....................................................................... 16
Initial Power-Up ......................................................................... 11
Ordering Guide .......................................................................... 16
REVISION HISTORY
7/05—Rev. 0 to Rev. A
Updated Absolute Maximum Ratings Page ...................................5
Updated Outline Dimensions ....................................................... 16
Changes to Ordering Guide .......................................................... 16
Revision 0: Initial Version
Rev. A | Page 2 of 16
AD8324
SPECIFICATIONS
TA = 25°C, VCC = 3.3 V, RL = RIN = 75 Ω, VIN (Differential) = 27.5 dBmV, unless otherwise noted. The AD8324 is characterized using a 1:1
transformer 1 at the device output.
Table 1.
Parameter
Conditions
Min
Typ
Max
Unit
INPUT CHARACTERISTICS
Specified AC Voltage
Input Resistance
Output = 61 dBmV, Max Gain
Single-Ended Input
Differential Input
27.5
550
1100
2
Input Capacitance
dBmV
Ω
Ω
pF
GAIN CONTROL INTERFACE
Voltage Gain Range
Max Gain
Min Gain
Output Step Size 2
Output Step Size Temperature Coefficient
TA = –40°C to +85°C
59.0
33.5
–25.5
1.0
±0.004
All Gain Codes (1–60 Decimal Codes)
f = 65 MHz
Max Gain, f = 10 MHz, Output Referred
Min Gain, f = 10 MHz, Input Referred
100
1.7
21
3.7
Gain Code = 60 Dec
Gain Code = 1 Dec
58
32.5
–26.5
0.6
60
34.5
–24.5
1.4
dB
dB
dB
dB/LSB
dB/°C
OUTPUT CHARACTERISTICS
Bandwidth (–3 dB)
Bandwidth Roll-Off
1 dB Compression Point 3
Output Noise2
Max Gain
Min Gain
Transmit Disable
Noise Figure2
Max Gain
Differential Output Impedance
19.6
2.1
MHz
dB
dBm
dBm
f = 10 MHz
f = 10 MHz
f = 10 MHz
157
1.3
1.1
166
1.5
1.2
nV/√Hz
nV/√Hz
nV/√Hz
f = 10 MHz
TX Enable and TX Disable
15.5
75 ± 30% 4
16.0
dB
Ω
f = 33 MHz, VOUT = 61 dBmV @ Max Gain
f = 65 MHz, VOUT = 61 dBmV @ Max Gain
f = 21 MHz, VOUT = 61 dBmV @ Max Gain
f = 65 MHz, VOUT = 61 dBmV @ Max Gain
Max Gain, f = 65 MHz
–66
–58
–59
–54
–61
–75
–60
–53
–57.5
–52.5
–58
–70
dBc
dBc
dBc
dBc
dBc
dB
Max Gain, VIN = 0
Max Gain, VIN = 0
Equivalent Output = 31 dBmV
Equivalent Output = 61 dBmV
2.5
3.8
2.5
27
6
71
μs
μs
mV p-p
mV p-p
Min to Max Gain
Max Gain, VIN = 27.5 dBmV
60
30
OVERALL PERFORMANCE
Second-Order Harmonic Distortion5, 3
Third-Order Harmonic Distortion 5 , 3
ACPR 2, 6
Isolation (Transmit Disable)2
POWER CONTROL
TX Enable Settling Time
TX Disable Settling Time
Output Switching Transients3
Output Settling
Due to Gain Change
Due to Input Step Change
ns
ns
POWER SUPPLY
Operating Range
Quiescent Current
OPERATING TEMPERATURE RANGE
Max Gain
Min Gain
Transmit Disable (TXEN = 0)
SLEEP Mode (Power-Down)
3.13
195
25
1
3.3
207
39
2.5
30
3.47
235
50
4
500
V
mA
mA
mA
μA
LFCSP
–40
+85
°C
QSOP
–25
+70
°C
1
TOKO 458PT-1556 used for above specifications. Typical insertion loss of 0.5 dB @ 10 MHz.
Guaranteed by design and characterization to ±6 sigma for TA = 25°C.
3
Guaranteed by design and characterization to ±3 sigma for TA = 25°C.
4
Measured through a 1:1 transformer.
5
Specification is worst case over all gain codes.
6
VIN = 27.5 dBmV, QPSK modulation, 160 kSPS symbol rate.
2
Rev. A | Page 3 of 16
AD8324
LOGIC INPUTS (TTL/CMOS COMPATIBLE LOGIC)
DATEN, CLK, SDATA, TXEN, SLEEP, VCC = 3.3 V, unless otherwise noted.
Table 2.
Parameter
Logic 1 Voltage
Logic 0 Voltage
Logic 1 Current (VINH = 3.3 V), CLK, SDATA, DATEN
Logic 0 Current (VINL = 0 V), CLK, SDATA, DATEN
Logic 1 Current (VINH = 3.3 V), TXEN
Logic 0 Current (VINL = 0 V), TXEN
Logic 1 Current (VINH = 3.3 V), SLEEP
Logic 0 Current (VINL = 0 V), SLEEP
Min
2.1
0
0
−600
50
−250
50
−250
Typ
Max
3.3
0.8
20
−100
190
−30
190
−30
Unit
V
V
nA
nA
μA
μA
μA
μA
Min
16.0
32.0
5.0
15.0
5.0
3.0
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
TIMING REQUIREMENTS
VCC = 3.3 V, tR = tF = 4 ns, fCLK = 8 MHz, unless otherwise noted.
Table 3.
Parameter
Clock Pulse Width (tWH)
Clock Period (tC)
Setup Time SDATA vs. Clock (tDS)
Setup Time DATEN vs. Clock (tES)
Hold Time SDATA vs. Clock (tDH)
Hold Time DATEN vs. Clock (tEH)
Input Rise and Fall Times, SDATA, DATEN, Clock (tR, tF)
10
tDS
SDATA
VALID DATA BIT
VALID DATA WORD G1
MSB . . . LSB
VALID DATA WORD G2
tC
tVUH
SDATA
MSB
MSB-1
MSB-2
CLK
tES
tEH
tDS
tDH
8 CLOCK CYCLES
GAIN TRANSFER (G1)
GAIN TRANSFER (G2)
04339-0-004
DATEN
CLK
tOFF
TXEN
Figure 4. SDATA Timng
tGS
SIGNAL AMPLITUDE (p-p)
04339-0-0030
tCN
ANALOG
OUTPUT
Figure 3. Serial Interface Timing
Rev. A | Page 4 of 16
AD8324
ABSOLUTE MAXIMUM RATINGS
Table 4. AD8324 Stress Ratings
Parameter
Supply Voltage VCC
Input Voltage
VIN+, VIN–
DATEN, SDATA, CLK, SLEEP, TXEN
Internal Power Dissipation
QSOP, LFCSP
Operating Temperature Range
LFCSP
QSOP
Storage Temperature Range
Lead Temperature (Soldering, 60 sec)
Rating
3.63 V
1.5 V p-p
–0.5 V to +3.63 V
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
776 mW
THERMAL RESISTANCE
–40°C to +85°C
–25°C to +70°C
–65°C to +150°C
300°C
Table 5. Thermal Resistance Ratings
Model
AD8324JRQ
AD8324ACP
1
2
θJA
83.2 1
30.4 2
Unit
°C/W
°C/W
Thermal resistance measured on SEMI standard 4-layer board.
Thermal resistance measured on SEMI standard 4-layer board, paddle
soldered to board.
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. A | Page 5 of 16
AD8324
20 19 18 17 16
VCC
GND 3
18
TXEN
GND 4
17
RAMP
4
5
13 VOUT–
12 BYP
11 NC
6
7
8
9
10
AD8324
VOUT+
TOP VIEW
VIN– 6 (Not to Scale) 15 VOUT–
5
16
GND 7
14
BYP
DATEN 8
13
NC
SDATA 9
12
SLEEP
CLK 10
11
GND
NC = NO CONNECT
Figure 5. 20-Lead LFCSP
04339-0-005
VIN–
GND
TOP VIEW
(Not to Scale)
VIN+
04339-0-006
3
14 VOUT+
SLEEP
VIN+
AD8324
GND
2
CLK
GND
15 RAMP
SDATA
1
DATEN
GND
VCC
GND
19
GND
20
VCC 2
GND
GND 1
VCC
TXEN
PIN CONFIGURATIONS AND FUNCTIONAL DESCRIPTIONS
Figure 6. 20-Lead QSOP
Table 6. Pin Function Descriptions
Pin No.
20-Lead
LFCSP
1, 2, 5, 9,
18, 19
17, 20
3
Pin No.
20-Lead
QSOP
1, 3, 4, 7,
11, 20
2, 19
5
4
6
6
8
VIN–
DATEN
7
9
SDATA
8
10
CLK
10
12
SLEEP
12
13
14
15
16
14
15
16
17
18
BYP
VOUT–
VOUT+
RAMP
TXEN
Mnemonic
GND
Description
Common External Ground Reference.
VCC
VIN+
Common Positive External Supply Voltage.
Noninverting Input. DC-biased to approximately VCC/2. Should be ac-coupled with a 0.1 μF
capacitor.
Inverting Input. DC-biased to approximately VCC/2. Should be ac-coupled with a 0.1 μF capacitor.
Data Enable Low Input. This port controls the 8-bit parallel data latch and shift register. A
Logic 0-to-1 transition transfers the latched data to the attenuator core (updates the gain) and
simultaneously inhibits serial data transfer into the register. A 1-to-0 transition inhibits the data
latch (holds the previous and simultaneously enables the register for serial data load).
Serial Data Input. This digital input allows an 8-bit serial (gain) word to be loaded into the internal
register with the MSB (most significant bit) first.
Clock Input. The clock port controls the serial attenuator data transfer rate to the 8-bit masterslave shift register. Logic 0-to-1 transition latches the data bit, and a 1-to-0 transfers the data bit
to the slave. This requires the input serial data-word to be valid at or before this clock transition.
Low Power Sleep Mode. In the sleep mode, the AD8324’s supply current is reduced to 30 μA. A
Logic 0 powers down the part (high ZOUT state), and a Logic 1 powers up the part.
Internal Bypass. This pin must be externally decoupled (0.1 μF capacitor).
Negative Output Signal. Must be biased to VCC. See Figure 23.
Positive Output Signal. Must be biased to VCC. See Figure 23.
External RAMP Capacitor (Optional).
Logic 0 disables forward transmission. Logic 1 enables forward transmission.
Rev. A | Page 6 of 16
AD8324
TYPICAL PERFORMANCE CHARACTERISTICS
–40
–40
VOUT = 62dBmV @ DEC 60
VOUT = 61dBmV @ DEC 60
–50
DISTORTION (dBc)
VOUT = 62dBmV @ DEC 60
VOUT = 61dBmV @ DEC 60
–60
–60
VOUT = 60dBmV @ DEC 60
–70
04339-0-007
–70
VOUT = 60dBmV @ DEC 60
–80
5
15
25
35
45
FREQUENCY (MHz)
55
04339-0-010
DISTORTION (dBc)
–50
–80
65
5
Figure 7. Second-Order Harmonic Distortion vs. Frequency
for Various Output Powers
15
25
35
45
FREQUENCY (MHz)
55
65
Figure 10. Third-Order Harmonic Distortion vs. Frequency
for Various Output Powers
–40
–40
VOUT = 61dBmV @ DEC 60
VOUT = 61dBmV @ DEC 60
TA = +25°C
TA = +85°C
–50
DISTORTION (dBc)
TA = –40°C
–60
TA = +25°C
–70
TA = –40°C
–60
04339-0-008
–70
TA = +85°C
–80
5
15
25
35
45
55
04339-0-011
DISTORTION (dBc)
–50
–80
65
5
15
FREQUENCY (MHz)
Figure 8. LFSCP Second-Order Harmonic Distortion
vs. Frequency vs. Temperature
55
65
Figure 11. LFCSP Third-Order Harmonic Distortion
vs. Frequency vs. Temperature
–40
–40
VOUT = 61dBmV @ DEC 60
VOUT = 61dBmV @ DEC 60
TA = +25°C
TA = +70°C
–50
DISTORTION (dBc)
–50
TA = +25°C
TA = –25°C
–60
–70
TA = –25°C
–60
TA = +70°C
–80
5
15
25
35
45
55
04339-0-012
–70
04339-0-009
DISTORTION (dBc)
25
35
45
FREQUENCY (MHz)
–80
65
5
FREQUENCY (MHz)
Figure 9. QSOP Second-Order Harmonic Distortion
vs. Frequency vs. Temperature
15
25
35
45
FREQUENCY (MHz)
55
Figure 12. QSOP Third-Order Harmonic Distortion
vs. Frequency vs. Temperature
Rev. A | Page 7 of 16
65
AD8324
0
60
CH PWR
12dBm
WORST ACP –61dBc
VOUT = 57dBmV/TONE
@ MAX GAIN
50
–20
40
–30
30
–40
20
VOUT (dBmV)
–50
–60
–70
10
0
–10
CU1
C0
C0
–90
–20
CU1
04339-0-013
–80
CL1
CL1
–100
CENTER 21 MHz
100 kHz/DIV
04339-0-016
POUT (dBm)
–10
–30
–40
41.6
SPAN 1 MHz
Figure 13. Adjacent Channel Power
41.7
41.8
41.9 42.0 42.1
42.2
FREQUENCY (MHz)
42.3
42.4
42.5
Figure 16. Two-Tone Intermodulation Distortion
40
0
TXEN = 0
VIN = 27.5dBmV
–10
30
DEC60
–20
DEC54
–30
GAIN (dB)
0
ISOLATION (dB)
DEC48
10
DEC42
DEC36
DEC30
–10
DEC24
–50
–60
–70
DEC18
DEC12
–80
–30
DEC 1 TO DEC 6
–40
0.1
1
10
FREQUENCY (MHz)
MAX GAIN
04339-0-014
–20
–40
100
04339-0-017
20
–90
MIN GAIN
–100
1000
100
10
FREQUENCY (MHz)
0
Figure 14. AC Response
1000
Figure 17. Isolation in Transmit Disable Mode vs. Frequency
1.4
2.0
1.5
1.2
1.0
GAIN ERROR (dB)
1.3
1.1
1.0
0.9
0.8
0.5
f = 5MHz
0
f = 10MHz
f = 42MHz
–0.5
–1.0
0.7
0.6
0
6
12
18
24
30
36
42
48
54
f = 65MHz
–1.5
04339-0-018
04339-0-015
OUTPUT STEP SIZE (dB)
f = 10MHz
–2.0
60
0
GAIN CONTROL (Decimal Code)
6
12
18
24
30
36
42
48
GAIN CONTROL (Decimal Code)
Figure 15. Output Step Size vs. Gain Control
Figure 18. Gain Error vs. Gain Control
Rev. A | Page 8 of 16
54
60
180
110
TXEN = 1
140
120
100
80
60
40
20
0
0
6
12
18
24
30
36
42
48
54
100
90
80
70
60
50
DOCSIS 2.0 BETWEEN BURST
TRANSIENT SPECIFICATION
40
30
AD8324
20
04339-0-021
160
BETWEEN BURSTS TRANSIENTS (mV p-p)
f = 10MHz
04339-0-019
OUTPUT REFERRED VOLTAGE NOISE (nV/ Hz)
AD8324
10
0
60
0
6
GAIN CONTROL (Decimal Code)
12
18
24
30
36
42
48
54
60
GAIN CONTROL (Decimal Code)
Figure 19. Output Referred Voltage Noise vs. Gain Control
Figure 21. Between Burst Transient vs. Gain Control
TA = 25°C
190
3.3V
170
0.1μF
10μF
150
18.7Ω
130
VCC
VIN+
110
OUT+
1:1
AD8324
39.5Ω
75Ω
RL
90
50
30
0
6
12
18
24
30
36
42
48
54
1/2 VIN
1/2 VIN
VIN–
OUT–
BYP GND
0.1μF
0.1μF
60
GAIN CONTROL (Decimal Code)
Figure 22. Typical Characterization Circuit
Figure 20. Supply Current vs. Gain Control
Rev. A | Page 9 of 16
04339-0-022
18.7Ω
70
04339-0-020
QUIESCENT SUPPLY CURRENT (mA)
210
AD8324
APPLICATIONS
GENERAL APPLICATIONS
The AD8324 is primarily intended for use as the upstream
power amplifier (PA) in DOCSIS (data over cable service
interface specification) certified cable modems and CATV settop boxes. The upstream signal is either a QPSK or QAM signal
generated by a DSP, a dedicated QPSK/QAM modulator, or a
DAC. In all cases, the signal must be low-pass filtered before
being applied to the PA in order to filter out-of-band noise and
higher order harmonics from the amplified signal.
Due to the varying distances between the cable modem and the
head-end, the upstream PA must be capable of varying the
output power by applying gain or attenuation. The ability to
vary the output power of the AD8324 ensures that the signal
from the cable modem will have the proper level once it arrives
at the head-end. The upstream signal path commonly includes a
diplexer and cable splitters. The AD8324 has been designed to
overcome losses associated with these passive components in
the upstream cable path.
CIRCUIT DESCRIPTION
The AD8324 is composed of three analog functions in the
transmit-enable mode. The input amplifier (preamp) can be
used in a single-ended or differential configuration. If the input
is used in the differential configuration, the input signals should
be 180 degrees out of phase and of equal amplitude. A vernier is
used in the input stage for controlling the fine 1 dB gain steps.
This stage then drives a DAC, which provides the bulk of the
AD8324’s attenuation. The signals in the preamp and DAC
blocks are differential to improve the PSRR and linearity. A
differential current is fed from the DAC into the output stage.
The output stage maintains 75 Ω differential output impedance
in all power modes.
GAIN PROGRAMMING FOR THE AD8324
The AD8324 features a serial peripheral interface (SPI) for
programming the gain code settings. The SPI interface consists
of three digital data lines: CLK, DATEN, and SDATA. The
DATEN pin should be held low while the AD8324 is being
programmed. The SDATA pin accepts the serial data stream for
programming the AD8324 gain code. The CLK pin accepts the
clock signal to latch in the data from the SDATA line.
The AD8324 utilizes a 6-bit shift register for clocking in the
data. The shift register is designed to be programmed MSB first.
The timing interface for programming the AD8324 can be seen
in Table 2, Table 3, Figure 3, and Figure 4. While the DATEN
pin is held low, the serial bits on the SDATA line are shifted into
the register on the rising edge of the CLK pin.
For existing software that uses 8-bits to program the cable
driver, the 2 MSBs will be ignored. This allows the AD8324 to
be compatible with some existing system designs.
The AD8324 recognizes gain codes 1 through 60 (all gain codes
are in decimal, unless otherwise noted). When the AD8324 is
programmed with 61 to 63, it will internally default to max gain
(gain code 60). If the programmed gain code is above 63, the
AD8324 will recognize only the 6 LSBs. For example, gain code
75 (01001011 binary) will be interpreted as gain code 11
(001011 binary) since the 2 MSBs are ignored.
The programming range of the AD8324 is from –25.5 dB (gain
code 1) to +33.5 dB (gain code 60). The 60 dB gain range is
linear with a 1 dB change in a 1 LSB change in gain code.
Figure 15 illustrates the gain step size of the AD8324 versus gain
code. The AD8324 was characterized with a differential input
signal and a TOKO 458PT-1457 1:1 transformer at the output.
INPUT BIAS, IMPEDANCE, AND TERMINATION
The VIN+ and VIN– inputs have a dc bias level of VCC/2; therefore
the input signal should be ac-coupled as seen in the typical
application circuit (Figure 23). The differential input impedance
of the AD8324 is approximately 1.1 kΩ, while the single-ended
input is 550 Ω. The high input impedance of the AD8324 allows
flexibility in termination and properly matching filter networks.
The AD8324 will exhibit optimum performance when driven
with a pure differential signal.
OUTPUT BIAS, IMPEDANCE, AND TERMINATION.
The output stage of the AD8324 requires a bias of 3.3 V. The
3.3 V power supply should be connected to the center tap of the
output transformer. Also, the VCC that is being applied to the
center tap of the transformer should be decoupled as seen in the
typical application circuit (Figure 23).
The output impedance of the AD8324 is 75 Ω, regardless of
whether the amplifier is in transmit enable, transmit disable, or
sleep mode. This, when combined with a 1:1 voltage ratio transformer, eliminates the need for external back termination
resistors. If the output signal is being evaluated using standard
50 Ω test equipment, a minimum loss 75 Ω to 50 Ω pad must
be used to provide the test circuit with the proper impedance
match. The AD8324 evaluation board provides a convenient
means to implement a matching attenuator. Soldering a 43.3 Ω
resistor in the R15 placeholder and an 86.6 Ω resistor in the R16
place-holder will allow testing on a 50 Ω system. When using a
matching attenuator, it should be noted that there will be 5.7 dB
of power loss (7.5 dB voltage) through the network.
Rev. A | Page 10 of 16
AD8324
VCC
10μF
AD8324-JRQ
1
2
0.1μF
3
VIN+
4
5
ZIN = 150Ω
174Ω
6
7
8
VIN–
9
0.1μF
10
GND
GND
VCC
VCC
GND
TXEN
GND
RAMP
VIN+
VOUT+
VIN–
VOUT–
GND
BYP
DATEN
NC
SDATA
SLEEP
GND
CLK
20
19
18
0.1μF
17
TO DIPLEXER
ZIN = 75Ω
1:1
16
15
TOKO 458PT-1556
14
13
0.1μF
12
11
1kΩ
DATEN
1kΩ
SDATA
1kΩ
CLK
04339-0-023
1kΩ
TXEN
1kΩ
SLEEP
Figure 23. Typical Application Circuit
Table 7. Adjacent Channel Power
Channel Symbol Rate (kSym/s)
160
320
640
1280
2560
5120
160
–63
–63
–64
–67
–70
–72
320
–64
–64
–64
–65
–67
–70
POWER SUPPLY
The 3.3 V supply should be delivered to each of the VCC pins via
a low impedance power bus. This ensures that each pin is at the
same potential. The power bus should be decoupled to ground
using a 10 μF tantalum capacitor located close to the AD8324.
In addition to the 10 μF capacitor, VCC pins should be decoupled
to ground with ceramic chip capacitors located close to the pins.
The bypass pin, labeled BYP, should also be decoupled. The
PCB should have a low impedance ground plane covering all
unused portions of the board, except in areas of the board
where input and output traces are in close proximity to the
AD8324 and the output transformer. All AD8324 ground pins
must be connected to the ground plane to ensure proper
grounding of all internal nodes.
Adjacent Channel Symbol Rate (kSym/s)
640
1280
2560
–68
–71
–72
–66
–70
–72
–65
–67
–71
–65
–66
–68
–66
–66
–67
–67
–67
–64
5120
–66
–67
–67
–67
–65
–64
input and output traces should be adequately spaced to
minimize coupling (crosstalk) through the board. Following
these guide-lines will optimize the overall performance of the
AD8324 in all applications.
INITIAL POWER-UP
When the supply voltage is first applied to the AD8324, the gain
of the amplifier is initially set to gain code 1. As power is first
applied to the amplifier, the TXEN pin should be held low
(Logic 0) to prevent forward signal transmission. After power
has been applied to the amplifier, the gain can be set to the
desired level by following the procedure provided in the Gain
Programming for the AD8324 section. The TXEN pin can then
be brought from Logic 0 to Logic 1, enabling forward signal
transmission at the desired gain level.
SIGNAL INTEGRITY LAYOUT CONSIDERATIONS
RAMP PIN AND BYP PIN FEATURES
Careful attention to printed circuit board layout details will
prevent problems due to board parasitics. Proper RF design
techniques are mandatory. The differential input and output
traces should be kept as short as possible. Keeping the traces
short will minimize parasitic capacitance and inductance, which
is most critical between the outputs of the AD8324 and the 1:1
output transformer. It is also critical that all differential signal
paths be symmetrical in length and width. In addition, the
The RAMP pin (Pin 15) is used to control the length of the burst
on and off transients. By default, leaving the RAMP pin
unconnected will result in a transient that is fully compliant with
DOCSIS 2.0 Section 6.2.21.2, Spurious Emissions During Burst
On/Off Transients. DOCSIS requires that all between burst
transients must be dissipated no faster than 2 μs. Adding
capacitance to the RAMP pin will slow the dissipation even more.
Rev. A | Page 11 of 16
AD8324
The BYP pin is used to decouple the output stage to ground.
Typically, for normal DOCSIS operation, the BYP pin should be
decoupled to ground with a 0.1 μF capacitor. However, in
applications that may require transient on/off times faster than
2 μs, smaller capacitors may be used, but it should be noted that
the BYP pin should always be decoupled to ground.
POWER SAVING FEATURES
The AD8324 incorporates three distinct methods of reducing
power consumption: transmit disable and sleep modes for
between-burst and shutdown modes, as well as gain dependent
quiescent current for transmit enable mode.
The asynchronous TXEN pin is used to place the AD8324 into
between-burst mode. In this reduced current state, the 75 Ω
output impedance is maintained. Applying Logic 0 to the TXEN
pin deactivates the on-chip amplifier, providing a 98.8% reduction in consumed power. For 3.3 V operation, the supply
current is typically reduced from 207 mA to 2.5 mA. In this
mode of operation, between-burst noise is minimized and high
input to output isolation is achieved. In addition to the TXEN
pin, the AD8324 also incorporates an asynchronous SLEEP pin,
which may be used to further reduce the supply current to
approximately 30 μA. Applying Logic 0 to the SLEEP pin places
the amplifier into SLEEP mode. Transitioning into or out of
SLEEP mode may result in a transient voltage at the output of
the amplifier.
In addition to the sleep and transmit disable functions, the
AD8324 provides yet another means of reducing system power
consumption. While in the transmit enable state, the AD8324
incorporates supply current scaling, which allows for lower
power consumption at lower gain codes. Figure 20 shows the
typical relationship between supply current and gain code.
DISTORTION, ADJACENT CHANNEL POWER, AND
DOCSIS
To deliver the DOCSIS required 58 dBmV of QPSK signal and
55 dBmV of 16 QAM signal, the PA is required to deliver up to
61 dBmV. This added power is required to compensate for
losses associated with the diplex filter or other passive components that may be included in the upstream path of cable
modems or set-top boxes. It should be noted that the AD8324
was characterized with a differential input signal. Figures 7 to
10 show the AD8324 second and third harmonic distortion
performance versus the fundamental frequency for various
output power levels. These figures are useful for determining
the in-band harmonic levels from 5 MHz to 65 MHz.
Harmonics higher in frequency (above 42 MHz for DOCSIS
and above 65 MHz for Euro-DOCSIS) will be sharply
attenuated by the low-pass filter function of the diplexer.
Another measure of signal integrity is adjacent channel power,
commonly referred to as ACP. DOCSIS 2.0, section 6.2.21.1.1
states, “Spurious emissions from a transmitted carrier may
occur in an adjacent channel that could be occupied by a carrier
of the same or different symbol rates.” Figure 13 shows the
typical ACP for a 61 dBmV (approximately 12 dBm) QPSK
signal taken at the output of the AD8324 evaluation board. The
transmit channel width and adjacent channel width in Figure 13
correspond to the symbol rates of 160 kSym/s. Table 7 shows
the ACP results for the AD8324 driving a QPSK, 61 dBmV
signal for all conditions in DOCSIS Table 6-9, Adjacent
Channel Spurious Emissions.
UTILIZING DIPLEX FILTERS
The AD8324 was designed to drive 61 dBmV without any
external filtering and still meet DOCSIS spurious emissions and
distortion requirements. However, in most upstream CATV
applications, a diplex filter is used to separate the upstream and
downstream signal paths from one another. The diplex filter
does have insertion loss that the upstream driver needs to overcome, but it also provides a low-pass filter. The addition of this
low-pass filter to the signal chain can greatly attenuate second
harmonic products of channels above 21 MHz and third
harmonic products of channels at or above 14 MHz up for
diplexers with a 42 MHz upstream cutoff. Similar performance
gains can be achieved using European-specified diplexers to
filter second harmonics for channels above 33 MHz and third
harmonics for channels above 22 MHz (65 MHz upstream
cutoff). This filtering allows the AD8324 to drive up to
63 dBmV of QPSK (this level can vary by application and
modulation type).
NOISE AND DOCSIS
At minimum gain, the AD8324 output noise spectral density is
1.3 nV/√Hz measured at 10 MHz. DOCSIS Table 6-10,
Spurious Emissions in 5 MHz to 42 MHz, specifies the output
noise for various symbol rates. The calculated noise power in
dBmV for 160 kSym/s is
20 × log [√(1.3 nV/√Hz)2 × 160 kHz] + 60 = –65.7 dBmV
Comparing the computed noise power of –65.7 dBmV to the
+8 dBmV signal yields –73.7 dBc, which meets the required
level set forth in DOCSIS Table 6-10. As the AD8324 gain is
increased above this minimum value, the output signal
increases at a faster rate than the noise, resulting in a signal-tonoise ratio that improves with gain. In transmit disable mode,
the output noise spectral density is 1.1 nV/√Hz, which results in
–67 dBmV when computed over 160 kSym/s. The noise power
was measured directly at the AD8324AR-EVAL’s output.
Rev. A | Page 12 of 16
AD8324
EVALUATION BOARD FEATURES AND OPERATION
DIFFERENTIAL SIGNAL SOURCE
Typical applications for the AD8324 use a differential input
signal from a modulator or a DAC. Refer to Table 8 for
common values of R4, or calculate other input configurations
using the equation in Figure 24. This circuit configuration will
give optimal distortion results due to the symmetric input
signals. It should be noted that this is the configuration that was
used to characterize the AD8324.
R4 =
ZIN × 1100Ω
1100Ω – ZIN
VIN+
ZIN
AD8324
VIN+
ZIN
VIN–
AD8324
R4
Figure 25. Single-to-Differential Circuit
SINGLE-ENDED SOURCE
Although the AD8324 was designed to have optimal DOCSIS
performance when used with a differential input signal, the
AD8324 may also be used as a single-ended receiver, or as an IF
digitally controlled amplifier. However, as with the single-ended
to differential configuration noted previously, even order
harmonic distortion will be slightly degraded.
When operating the AD8324 in a single-ended input mode,
terminate the part as illustrated in Figure 26. On the AD8324
evaluation boards, this termination method requires the
removal and shorting of R2 and R3, the removal of R4, as well
as the addition of 86.6 Ω at R1 and 40.2 Ω at R17 for 75 Ω
termination. Table 8 shows the correct values for R11 and R12
for some common input configurations. Other input impedance
configurations may be accommodated using the equations in
Figure 26.
04339-0-024
R4
ZIN × 1100Ω
1100Ω – ZIN
04339-0-025
The AD8324 evaluation board and control software can be used
to control the AD8324 upstream cable driver via the parallel
port of a personal computer. A standard printer cable connected
to the parallel port of the PC is used to feed all the necessary
data to the AD8324 using the Windows® based control software.
This package provides a means of controlling the gain and the
power mode of the AD8324. With this evaluation kit, the
AD8324 can be evaluated in either a single-ended or differential
input configuration. A schematic of the evaluation board is
provided in Figure 29.
R4 =
R1 =
Figure 24. Differential Circuit
ZIN × 550
550 – ZIN
R17 =
ZIN × R1
R1 – ZIN
VIN+
R1
AD8324
ZIN
The default configuration of the evaluation board implements a
differential signal drive from a single-ended signal source. This
configuration uses a 1:1 balun transformer to approximate a
differential signal. Because of the non-ideal nature of real
transformers, the differential signal is not purely equal and
opposite in amplitude. Although this circuit slightly sacrifices
even order harmonic distortion due to asymmetry, it does
provide a convenient way to evaluate the AD8324 with a singleended source. The AD8324 evaluation board is populated with
a TOKO 617DB-A0070 1:1 for this purpose (T1).
Table 8. Common Matching Resistors
Table 8 provides typical R4 values for common input
configurations. R16 must be removed, and R2 and R3 should be
shorted. Other input impedances may be calculated using the
equation in Figure 25. Refer to Figure 29 for an evaluation
board schematic. To use the transformer for converting a single
ended source into a differential signal, the input signal must be
applied to VIN+.
ZIN (Ω)
50
75
R17
04339-0-026
DIFFERENTIAL SIGNAL FROM
SINGLE-ENDED SOURCE
Figure 26. Single-Ended Circuit
ZIN (Ω)
50
75
100
150
Rev. A | Page 13 of 16
Differential Input Termination
R2/R3 (Ω)
R4 (Ω)
Open
52.3
Open
80.6
Open
110
Open
174
Single-Ended Input Termination
R2/R3 (Ω)
R4 (Ω)
0/0
Open
0/0
Open
R1/R17 (Ω)
Open/Open
Open/Open
Open/Open
Open/Open
R1/R17 (Ω)
54.9/26.1
86.6/40.2
AD8324
OVERSHOOT ON PC PRINTER PORTS
The data lines on some PC parallel printer ports have excessive
overshoot, which may cause communications problems when
presented to the CLK pin of the AD8324. The evaluation board
was designed to accommodate a series resistor and shunt
capacitor (R9 and C5 in Figure 29) to filter the CLK signal if
required. For parallel ports with logic levels above 3.3 V, R9 and
C5 may be used as an attenuator.
CONTROLLING GAIN/ATTENUATION
OF THE AD8324
The slide bar controls the gain/attenuation of the AD8324,
which is displayed in dB and in V/V. The gain scales 1 dB per
LSB. The gain code from the position of the slide bar is
displayed in decimal, binary, and hexadecimal (Figure 28).
INSTALLING VISUAL BASIC CONTROL SOFTWARE
Install the CabDrive_24 software by running the setup.exe file
on disk one of the AD8324 evaluation software. Follow the onscreen directions and insert disk two when prompted. Choose
the installation directory and then select the icon in the upper
left to complete the installation.
RUNNING AD8324 SOFTWARE
04339-0-028
To load the control software, go to START, PROGRAMS,
CABDRIVE_24 or select the AD8324.exe file from the installed
directory. Once loaded, select the proper parallel port to
communicate with the AD8324 (Figure 27).
Figure 28. Control Software Interface
04339-0-027
TRANSMIT ENABLE AND SLEEP MODE
Figure 27. Parallel Port Selection
The Transmit Enable and Transmit Disable buttons select the
mode of operation of the AD8324 by asserting logic levels on
the asynchronous TXEN pin. The Transmit Disable button
applies Logic 0 to the TXEN pin, disabling forward transmission. The Transmit Enable button applies Logic 1 to the TXEN
pin, enabling the AD8324 for forward transmission. Checking
the Enable SLEEP Mode checkbox applies Logic 0 to the asynchronous SLEEP pin, setting the AD8324 for SLEEP mode.
MEMORY FUNCTIONS
The Memory section of the software provides a way to alternate
between two gain settings. The X–>M1 button stores the
current value of the gain slide bar into memory, while the RM1
button recalls the stored value, returning the gain slide bar to
the stored level. The same applies to the X–>M2 and RM2
buttons.
Rev. A | Page 14 of 16
AD8324
TP9A
3 T1A 1
R1A
OPEN
2
6
4
TOKO1
VIN–_A
R3A
OPEN
R17A
OPEN
R4A
73.4Ω
VCC1
C2A
0.1μF
1
3
R5A
1kΩ
R6A
0Ω
2
C3A
OPEN
4
5
6
7
8
9
TP2A
P1 3
R7A
1kΩ
10
R8A
0Ω
AD8324
GND
GND
VCC
VCC
GND
TXEN
GND
RAMP
VIN+
VOUT+
VIN–
VOUT–
GND
BYP
DATAEN
SDATA
CLK
C8A
10μF
C9A
OPEN
DUT1
2
TP1A
P1
C1A
0.1μF
R2A
OPEN
VIN+_A
NC
SLEEP
GND
20
19
18
17
C10A
0.1μF
C11A
OPEN
16
15
1 T2A
14
13
12
11
C12A
0.1μF
VCC1
2
R15A
0Ω
6
4
3
TOKOB5F
CABLE_0A
R16A
OPEN
C13A
0.1μF
C4A
OPEN
P1 19
P1 20
TP3A
P1
5
R9A
1kΩ
P1 21
R10A
0Ω
P1 22
P1 23
C5A
OPEN
P1 24
P1 25
TP4A
P1
6
R11A
1kΩ
P1 26
R12A
0Ω
P1 27
TP10A
C6A
OPEN
TP11A
TP12A
TP5A
R13A
1kΩ
P1
P1 28
P1 29
P1 30
TP_AGND1 TP_VCC1
AGND1
VCC1
R14A
0Ω
P1 31
7
04339-0-029
C7A
OPEN
P1 16
Figure 29. AD8324 Evaluation Board Schematic
Rev. A | Page 15 of 16
AD8324
OUTLINE DIMENSIONS
0.60
MAX
4.00
BSC SQ
0.60
MAX
PIN 1
INDICATOR
TOP
VIEW
20 1
16
15
2.25
2.10 SQ
1.95
3.75
BCS SQ
0.75
0.55
0.35
11
10
5
0.30
0.23
0.18
0.05 MAX
0.02 NOM
0.20
REF
6
0.25 MIN
0.80 MAX
0.65 TYP
12° MAX
1.00
0.85
0.80
SEATING
0.50
PLANE
BSC
PIN 1
INDICATOR
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VGGD-1
Figure 30. 20-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
4 mm × 4 mm Body, Very Thin Quad (CP-20-1)
Dimensions shown in millimeters
0.341
BSC
20
11
0.154
BSC
1
0.236
BSC
10
PIN 1
0.065
0.049
0.010
0.004
0.069
0.053
0.025
BSC
0.012
0.008
SEATING
PLANE
COPLANARITY
0.004
0.010
0.006
8°
0°
0.050
0.016
COMPLIANT TO JEDEC STANDARDS MO-137-AD
Figure 31. 20-Lead Shrink Small Outline Package [QSOP] (RQ-20)
Dimensions shown in inches
ORDERING GUIDE
Model
AD8324JRQ
AD8324JRQ-REEL
AD8324JRQ-REEL7
AD8324JRQZ 1
AD8324JRQZ-REEL1
AD8324JRQZ-REEL71
AD8324ACP
AD8324ACP-REEL7
AD8324ACPZ1
AD8324ACPZ-REEL71
AD8324JRQ-EVAL
AD8324ACP-EVAL
1
Temperature Range
–25°C to +70°C
–25°C to +70°C
–25°C to +70°C
–25°C to +70°C
–25°C to +70°C
–25°C to +70°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
–40°C to +85°C
Package Description
20-Lead QSOP
20-Lead QSOP
20-Lead QSOP
20-Lead QSOP
20-Lead QSOP
20-Lead QSOP
20-Lead LFCSP_VQ
20-Lead LFCSP_VQ
20-Lead LFCSP_VQ
20-Lead LFCSP_VQ
Evaluation Board
Evaluation Board
Z = Pb-free part.
© 2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
C04339–0–7/05(A)
Rev. A | Page 16 of 16
Package Option
RQ-20
RQ-20
RQ-20
RQ-20
RQ-20
RQ-20
CP-20-1
CP-20-1
CP-20-1
CP-20-1