AZM AZ100EL16D+

ARIZONA MICROTEK, INC.
AZ10EL16
AZ100EL16
ECL/PECL Differential Receiver
FEATURES
•
•
•
•
•
PACKAGE AVAILABILITY
RoHS Compliant / Lead (Pb) Free Package
Available
250ps Propagation Delay
High Bandwidth Output Transitions
75kΩ Internal Input Pulldown Resistors
Direct Replacement for ON Semiconductor
MC10EL16 & MC100EL16
PACKAGE
PART NUMBER
MARKING
NOTES
AZM10
EL16
AZM100
EL16
SOIC 8
AZ10EL16D
SOIC 8
AZ100EL16D
SOIC 8 RoHS
Compliant /
Lead (Pb) Free
AZ100EL16D+
AZM100+
EL16
1,2
TSSOP 8
AZ10EL16T
AZT16T
1,2
AZ100EL16T
AZH16T
1,2
TSSOP 8
1
2
1,2
1,2
Add R1 at end of part number for 7 inch (1K parts), R2 for 13 inch (2.5K
parts) Tape & Reel.
Date code format: “Y” or “YY” for year followed by “WW” for week on
underside of part.
DESCRIPTION
The AZ10/100EL16 is a differential receiver. The device is functionally equivalent to the E116 device with
higher performance capabilities. With output transition times significantly faster than the E116, the EL16 is ideally
suited for interfacing with high frequency sources.
The EL16 provides a VBB output for either single-ended use or a DC bias reference for AC coupling to the
device. For single-ended input applications, the VBB reference should be connected to one side of the D/D
¯ differential
input pair. The input signal is then fed to the other D/D
¯ input. The VBB pin can support 1.0mA sink/source current.
When used, the VBB pin should be bypassed to ground via a 0.01μF capacitor.
Under open input conditions (pulled to VEE) internal input clamps will force the Q output LOW.
NOTE: Specifications in the ECL/PECL tables are valid when thermal equilibrium is established.
LOGIC DIAGRAM AND PINOUT ASSIGNMENT
PIN DESCRIPTION
PIN
D, D
¯
Q, Q
¯
VBB
VCC
VEE
NC
FUNCTION
Data Inputs
Data Outputs
Reference Voltage Output
Positive Supply
Negative Supply
No Connect
NC
1
8
VCC
D
2
7
Q
D
3
6
Q
VBB
4
5
VEE
1630 S. STAPLEY DR., SUITE 127 • MESA, ARIZONA 85204 • USA • (480) 962-5881 • FAX (480) 890-2541
www.azmicrotek.com
AZ10EL16
AZ100EL16
Absolute Maximum Ratings are those values beyond which device life may be impaired.
Symbol
VCC
VI
VEE
VI
Characteristic
PECL Power Supply (VEE = 0V)
PECL Input Voltage
(VEE = 0V)
ECL Power Supply
(VCC = 0V)
ECL Input Voltage
(VCC = 0V)
Output Current
--- Continuous
--- Surge
Operating Temperature Range
Storage Temperature Range
IOUT
TA
TSTG
Rating
0 to +8.0
0 to +6.0
-8.0 to 0
-6.0 to 0
50
100
-40 to +85
-65 to +150
Unit
Vdc
Vdc
Vdc
Vdc
mA
°C
°C
10K ECL DC Characteristics (VEE = -4.75V to -5.5V, VCC = GND)
Symbol
Characteristic
1
Min
-1080
-1950
-1230
-1950
-1430
-40°C
Typ
Max
-890
-1650
-890
-1500
-1300
150
VOH
Output HIGH Voltage
VOL
Output LOW Voltage1
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
VBB
Reference Voltage
Input HIGH Current
IIH
Input LOW Current
0.5
IIL
IEE
Power Supply Current
18
22
1.
Each output is terminated through a 50Ω resistor to VCC – 2V.
Min
-1020
-1950
-1170
-1950
-1380
0°C
Typ
Max
-840
-1630
-840
-1480
-1270
150
0.5
Min
-980
-1950
-1130
-1950
-1350
25°C
Typ
Max
-810
-1630
-810
-1480
-1250
150
0.5
18
22
Min
-910
-1950
-1060
-1950
-1310
85°C
Typ
Max
-720
-1595
-720
-1445
-1190
150
0.5
18
22
18
22
Unit
mV
mV
mV
mV
mV
μA
μA
mA
10K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol
Characteristic
1,2
Min
3920
3050
3770
3050
3570
-40°C
Typ
Max
4110
3350
4110
3500
3700
150
Min
3980
3050
3830
3050
3620
0°C
Typ
Max
4160
3370
4160
3520
3730
150
Min
4020
3050
3870
3050
3650
VOH
Output HIGH Voltage
VOL
Output LOW Voltage1,2
VIH
Input HIGH Voltage1
VIL
Input LOW Voltage1
VBB
Reference Voltage1
IIH
Input HIGH Current
Input LOW Current
0.5
0.5
0.5
IIL
IEE
Power Supply Current
18
22
18
22
1.
For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2.
Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
Max
4190
3370
4190
3520
3750
150
Min
4090
3050
3940
3050
3690
85°C
Typ
Max
4280
3405
4280
3555
3810
150
0.5
18
22
18
22
Unit
mV
mV
mV
mV
mV
μA
μA
mA
100K ECL DC Characteristics (VEE = -4.2V to -5.5V, VCC = GND)
Symbol
Characteristic
1
Min
-1085
-1830
-1165
-1810
-1380
-40°C
Typ
-1005
-1695
Max
-880
-1555
-880
-1475
-1260
150
VOH
Output HIGH Voltage
VOL
Output LOW Voltage1
VIH
Input HIGH Voltage
VIL
Input LOW Voltage
VBB
Reference Voltage
Input HIGH Current
IIH
Input LOW Current
0.5
IIL
IEE
Power Supply Current
18
22
1.
Each output is terminated through a 50Ω resistor to VCC – 2V.
May 2007 * REV - 3
Min
-1025
-1810
-1165
-1810
-1380
0°C
Typ
-955
-1705
Max
-880
-1620
-880
-1475
-1260
150
0.5
Min
-1025
-1810
-1165
-1810
-1380
25°C
Typ
-955
-1705
Max
-880
-1620
-880
-1475
-1260
150
0.5
18
www.azmicrotek.com
2
22
Min
-1025
-1810
-1165
-1810
-1380
85°C
Typ
-955
-1705
Max
-880
-1620
-880
-1475
-1260
150
0.5
18
22
21
26
Unit
mV
mV
mV
mV
mV
μA
μA
mA
AZ10EL16
AZ100EL16
100K PECL DC Characteristics (VEE = GND, VCC = +5.0V)
Symbol
Characteristic
1,2
Min
3915
3170
3835
3190
3620
-40°C
Typ
3995
3305
Max
4120
3445
4120
3525
3740
150
Min
3975
3190
3835
3190
3620
0°C
Typ
4045
3295
Max
4120
3380
4120
3525
3740
150
Min
3975
3190
3835
3190
3620
VOH
Output HIGH Voltage
VOL
Output LOW Voltage1,2
VIH
Input HIGH Voltage1
VIL
Input LOW Voltage1
VBB
Reference Voltage1
IIH
Input HIGH Current
Input LOW Current
0.5
0.5
0.5
IIL
IEE
Power Supply Current
18
22
18
22
1.
For supply voltages other that 5.0V, use the ECL table values and ADD supply voltage value.
2.
Each output is terminated through a 50Ω resistor to VCC – 2V.
25°C
Typ
4045
3295
Max
4120
3380
4120
3525
3740
150
Min
3975
3190
3835
3190
3620
85°C
Typ
4045
3295
Max
4120
3380
4120
3525
3740
150
0.5
18
22
21
26
Unit
mV
mV
mV
mV
mV
μA
μA
mA
AC Characteristics (VEE =10E(-4.75V to -5.5V), 100E(-4.2V to -5.5V); VCC=GND or VEE =GND; VCC =10E(+4.75V to +5.5V),
100E(+4.2V to +5.5V) )
Symbol
Characteristic
VPP (AC)
Propagation Delay
to Output
(Diff)
(SE)
Duty Cycle Skew 1
(Diff)
Minimum Input Swing2
VCMR
Common Mode Range3
tPLH / tPHL
tSKEW
Min
-40°C
Typ
Max
Min
0°C
Typ
Max
Min
25°C
Typ
Max
Min
85°C
Typ
Max
125
75
250
250
375
425
175
125
250
250
325
375
175
125
250
250
325
375
205
155
280
280
355
405
5
20
5
20
5
20
VCC –
0.4
150
VCC –
2.0
5
150
VCC –
2.0
VCC –
0.4
150
VCC –
2.0
VCC –
0.4
150
VCC –
2.0
Unit
ps
ps
mV
VCC –
0.4
V
Output Rise/Fall Times
tr / t f
100
350
100
350
100
350
100
350
ps
Q (20% - 80%)
1.
Duty cycle skew is the difference between a tPLH and tPHL propagation delay through a device.
2.
VPP is the minimum peak-to-peak differential input swing for which AC parameters are guaranteed. The device has a DC gain of ≈ 40.
3.
The VCMR range is referenced to the most positive side of the differential input signal. Normal operation is obtained if the HIGH level falls within the
specified range and the peak-to-peak voltage lies between VPP (min) and 1V.
May 2007 * REV - 3
www.azmicrotek.com
3
AZ10EL16
AZ100EL16
PACKAGE DIAGRAM
SOIC 8
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
May 2007 * REV - 3
DIM
A
A1
A2
A3
bp
c
D
E
e
HE
L
Lp
Q
v
w
y
Z
θ
www.azmicrotek.com
4
MILLIMETERS
MIN
MAX
1.75
0.10
0.25
1.25
1.45
0.25
0.36
0.49
0.19
0.25
4.8
5.0
3.8
4.0
1.27
5.80
6.20
1.05
0.40
1.00
0.60
0.70
0.25
0.25
0.10
0.30
0.70
8O
0O
INCHES
MIN
MAX
0.069
0.004
0.010
0.049
0.057
0.01
0.014
0.019
0.0075
0.0100
0.19
0.20
0.15
0.16
0.050
0.228
0.244
0.041
0.016
0.039
0.024
0.028
0.01
0.01
0.004
0.012
0.028
0O
8O
AZ10EL16
AZ100EL16
PACKAGE DIAGRAM
TSSOP 8
DIM
A
A1
A2
A3
bp
c
D
E
e
HE
L
Lp
v
w
y
Z
θ
NOTES:
1.
DIMENSIONS D AND E DO NOT
INCLUDE MOLD PROTRUSION.
2.
MAXIMUM MOLD PROTRUSION
FOR D IS 0.15mm.
3.
MAXIMUM MOLD PROTRUSION
FOR E IS 0.25mm.
May 2007 * REV - 3
www.azmicrotek.com
5
MILLIMETERS
MIN
MAX
1.10
0.05
0.15
0.80
0.95
0.25
0.25
0.45
0.15
0.28
2.90
3.10
2.90
3.10
0.65
4.70
5.10
0.94
0.40
0.70
0.10
0.10
0.10
0.35
0.70
6O
0O
AZ10EL16
AZ100EL16
Arizona Microtek, Inc. reserves the right to change circuitry and specifications at any time without prior notice. Arizona Microtek, Inc. makes no
warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does Arizona Microtek, Inc. assume
any liability arising out of the application or use of any product or circuit and specifically disclaims any and all liability, including without
limitation special, consequential or incidental damages. Arizona Microtek, Inc. does not convey any license rights nor the rights of others.
Arizona Microtek, Inc. products are not designed, intended or authorized for use as components in systems intended to support or sustain life, or
for any other application in which the failure of the Arizona Microtek, Inc. product could create a situation where personal injury or death may
occur. Should Buyer purchase or use Arizona Microtek, Inc. products for any such unintended or unauthorized application, Buyer shall indemnify
and hold Arizona Microtek, Inc. and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages,
and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such
unintended or unauthorized use, even if such claim alleges that Arizona Microtek, Inc. was negligent regarding the design or manufacture of the
part.
May 2007 * REV - 3
www.azmicrotek.com
6