GAMEWELL-FCI B501

ASD-LS
ANALOG ADDRESSABLE LASER
SMOKE SENSOR
DESCRIPTION
The FCI Model ASD-LS low profile laser smoke sensor
adds another new dimension to analog addressable fire detection. It incorporates laser smoke detection technology that
provides unsurpassed sensitivity and response to maximize
detection. This makes the sensor ultra-sensitive to smoke, as
much as 100 times more sensitive than conventional photoelectric smoke detection technology.
An innovative laser diode and precision optics design combine with an array of integral software tools to make the
quickest possible decision in the event of a genuine fire. The
sensor can swiftly sense smoldering fires, but yet can sense
the smallest particles of combustion, providing a faster response to flaming fires.
The early warning capability of the ASD-LS is comparable
to that of aspiration technology, while unlike aspirating systems, the ASD-LS can pin-point the location of the fire.
The sensor is continually monitored to measure any change
in its sensitivity due to the environment (dirt, temperature,
transient smoke, humidity, etc.). Patented algorithms distinguish between particles of dust and smoke. The focused
beam of the laser light source minimizes reflection from accumulated dust in the optical chamber, effectively minimizing problems caused by dust build-up. The software
performs its own independent analyses of the sensor signal.
These analyses include dust spike rejection, drift compensation, smoothing, multi-sensor, pre-alarm decision and alarm
decision. In the event of spikes in the signal, the sensor will
check the output of adjacent sensors for any appreciable signal to determine if the spike is caused by a fast flaming fire.
The sensor is of plug-in construction and is directly interchangeable in the same base with the FCI ASD/ATD/Acclimate Series low-profile sensors. A wide variety of bases,
with sounder, relay, etc. is available. Remote LED annunciator capability is also available as an optional accessory.
The ASD-LS sensor is Listed for use inside ducts up to a
velocity of 4,000 FPM.
An optional isolator base, Model B224BI, is also available.
Installation of two of these isolator bases allows Style 7 operation for sensors located electrically between the bases.
•
•
•
•
•
•
•
•
•
•
•
•
FEATURES
Compatible with FCI Analog
Addressable Control Panels
High Sensitivity for Both Smoldering
and Fast Flaming Fires
Patented Algorithms Ignore Transient
Smoke and Dust Particles
Low Profile Construction
Easy Plug-in of the Head to Base
Built-in Signal Processing
Built-in Tamper-Resistant Feature
Remote Test Feature (From the Panel)
Built-in Test Switch
360o View Angle of Dual Alarm LEDs
Optional Bases for Auxiliary Functions
Maximum Air Velocity 4,000 FPM
TECHNICAL SPECIFICATIONS
Sensitivity
Operating voltage
Standby current
Alarm current (max.)
Operating/Installation Temperature
Operating humidity
Dimensions
Weight
.02 - 0.8%/ft.
15-32 VDC
.00033 amp.
.0065 amp.
32 to 100o F (0 to 38o C)
10% to 93% relative humidity (non condensing)
1.7" H x 6.2" Dia. (4.3 x 15 cm) (In standard base)
5 oz. (142 gm.)
Specifications are provided for information only, are not intended to be used for installation purposes, and are believed to be accurate. However, no responsibility is assumed
by Gamewell-FCI for their use. Specifications subject to change without notice.
© 2006 All Rights Reserved
GAMEWELL-FCI
12 Clintonville Road, Northford, CT 06472 - Tel: (203) 484-7161 Fax: (203) 484-7118
www.gamewell-fci.com
An ISO 9001 Certified Company
9020-0525 Rev. B
MAINTENANCE
INSTALLATION
Place the sensor into the sensor base. Turn the sensor
clockwise until the sensor locks into place.
To use the tamper-proof feature, break the smaller tab
on the base as shown in the installation instructions. Install the sensor. To remove the sensor from the base
when using the tamper-proof feature, insert the blade of
a small screwdriver into the hole on the side of the base
and push the plastic lever away from the detector head.
This will allow the sensor to be rotated counterclockwise for removal. NOTE: The decorative ring must be
removed in order to remove the head when using the
tamper-proof feature.
Refer to NFPA 72, Chapter 5-3 “Smoke Sensing Fire
Detectors” for spacing, location of sensors and other
guidelines.
Cleaning programs should be adapted to the individual environment in conformance with the National Fire
Alarm Code, NFPA 72. We recommend, at the least, an
annual cleaning of the unit. The sensor screen and cover
assembly can be removed, revealing the sensing chamber. A vacuum cleaner can be used to remove dust from
the screen, cover and sensing chamber. For the complete procedure, refer to the Installation and Maintenance Instructions furnished with each sensor.
TESTING
Sensors may be tested locally in the following ways:
• A. Place a test magnet against the sensor housing
per the instructions. The sensor should go into
alarm within 30 seconds.
• B. Aerosol Generator - The Gemini Model 501
aerosol generator may be used to perform a
functional test. This test should be performed
immediately following the magnet test. Magnet
test initiates an approximately ten minute period
when the detector's signal processing software
routines are not active. Failure to first perform the
magnet test will introduce a time delay before the
detector alarms. Follow instructions in the
generator instruction manual.
AGENCY APPROVALS
UL (Std 268)
Factory Mutual
S1913
Pending
ORDERING INFORMATION
2 of 2
Part No.
110-90039
110-90005
110-90004
Model
ASD-LS
ADB-FL
B224RB
Description
Low Profile Analog Laser Sensor
Standard plug-in sensor base with flange and decorative ring
Plug-in sensor base with auxiliary relay, SPDT,
rated 2 amps. @ 30 VDC (resistive)
110-90006
130-90037
110-31A60
138-01005
119-9010N
B224BI
B501BHT
B501
RA-400Z
Plug-in sensor isolator base for Style 7 operation
Plug-in sensor base with temporal pattern sounder
Plug-in sensor base w/o flange
Remote alarm indicator
Detector sensitivity test kit.
9020-0525Rev. B