Low Power, Low Cost 2.5 V Reference AD680 GENERAL DESCRIPTION The AD680 is a band gap voltage reference that provides a fixed 2.5 V output from inputs between 4.5 V and 36 V. The architecture of the AD680 enables the reference to be operated at a very low quiescent current while still realizing excellent dc characteristics and noise performance. Trimming of the high stability thin-film resistors is performed for initial accuracy and temperature coefficient, resulting in low errors over temperature. The precision dc characteristics of the AD680 make it ideal for use as a reference for DACs that require an external precision reference. The device is also ideal for ADCs and, in general, can offer better performance than the standard on-chip references. Based upon its low quiescent current, which rivals that of many incomplete 2-terminal references, the AD680 is recommended for low power applications, such as hand-held, battery-operated equipment. A temperature output pin is provided on the 8-lead package versions of the AD680. The temperature output pin provides an output voltage that varies linearly with temperature and allows the AD680 to be configured as a temperature transducer while providing a stable 2.5 V output. The AD680 is available in five grades. The AD680AN is specified for operation from −40°C to +85°C, while the AD680JN is specified for 0°C to 70°C operation. Both the AD680AN and AD680JN are available in 8-lead PDIP packages. The AD680AR is specified for operation from −40°C to +85°C, while the AD680JR is specified for 0°C to 70°C operation. Both are available in 8-lead SOIC packages. The AD680JT is specified for 0°C to 70°C operation and is available in a 3-pin TO-92 package. CONNECTION DIAGRAMS TP* 1 +VIN 2 AD680 8 TP* 7 TP* 6 VOUT TOP VIEW (Not to Scale) 5 NC GND 4 TEMP 3 NC = NO CONNECT * TP DENOTES FACTORY TEST POINT. NO CONNECTIONS SHOULD BE MADE TO THESE PINS. 00813-003 Low quiescent current at 250 μA max Laser trimmed to high accuracy 2.5 V ± 5 mV max (AN, AR grades) Trimmed temperature coefficient 20 ppm/°C max (AN, AR grades) Low noise at 8 μV p-p from 0.1 Hz to 10 Hz 250 nV/√Hz wideband Temperature output pin (N, R packages) Available in three package styles 8-lead PDIP, 8-lead SOIC, and 3-pin TO-92 Figure 1. 8-Lead PDIP and 8-Lead SOIC Pin Configuration AD680 BOTTOM VIEW (Not to Scale) 3 2 1 +VIN VOUT GND 00813-004 FEATURES Figure 2. Connection Diagram TO-92 PRODUCT HIGHLIGHTS 1. High Accuracy. The AD680 band gap reference operates on a very low quiescent current which rivals that of many 2-terminal references. This makes the complete, higher accuracy AD680 ideal for use in power-sensitive applications. 2. Low Errors. Laser trimming of both initial accuracy and temperature coefficients results in low errors over temperature without the use of external components. The AD680AN and AD680AR have a maximum variation of 6.25 mV between −40°C and +85°C. 3. Low Noise. The AD680 noise is low, typically 8 μV p-p from 0.1 Hz to 10 Hz. Spectral density is also low, typically 250 nV/√Hz. 4. Temperature Transducer. The temperature output pin on the 8-lead package versions enables the AD680 to be configured as a temperature transducer. 5. Low Cost. PDIP packaging provides machine insertability, while SOIC packaging provides surface-mount capability. TO-92 packaging offers a cost-effective alternative to 2-terminal references, offering a complete solution in the same package in which 2-terminal references are usually found. Rev. H Information furnished by Analog Devices is believed to be accurate and reliable. However, no responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other rights of third parties that may result from its use. Specifications subject to change without notice. No license is granted by implication or otherwise under any patent or patent rights of Analog Devices. Trademarks and registered trademarks are the property of their respective owners. One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A. Tel: 781.329.4700 www.analog.com Fax: 781.461.3113 ©2005 Analog Devices, Inc. All rights reserved. AD680 TABLE OF CONTENTS Specifications..................................................................................... 3 Load Regulation ............................................................................8 Absolute Maximum Ratings............................................................ 4 Temperature Performance............................................................8 Output Protection ........................................................................ 4 Temperature Output Pin ..............................................................9 ESD Caution.................................................................................. 4 Differential Temperature Transducer .........................................9 Pin Configuration and Connection Diagram............................... 5 Low Power, Low Voltage Reference for Data Converters ........9 Theory of Operation ........................................................................ 6 4.5 V Reference from a 5 V Supply .......................................... 10 Applying the AD680 .................................................................... 6 Voltage Regulator for Portable Equipment ............................. 10 Noise Performance ....................................................................... 6 Outline Dimensions ....................................................................... 11 Turn-on Time................................................................................ 7 Ordering Guide .......................................................................... 12 Dynamic Performance................................................................. 7 REVISION HISTORY 8/05—Rev. G to Rev. H Changes to Ordering Guide ..........................................................11 12/04—Rev. F to Rev. G Updated Format ................................................................. Universal Changes to Ordering Guide ..........................................................11 5/04—Rev. E to Rev. F Changes to ORDERING GUIDE ...................................................3 5/03—Rev. D to Rev. E Changes to ORDERING GUIDE ...................................................3 Added ESD Caution ..........................................................................3 Changes to Figure 20.........................................................................7 Updated OUTLINE DIMENSIONS ...............................................8 7/01—Rev. C to Rev. D Changes to SPECIFICATIONS........................................................2 Changes to ORDERING GUIDE ....................................................3 Table I added ......................................................................................6 Rev. H | Page 2 of 12 AD680 SPECIFICATIONS TA = 25°C, VIN = 5 V, unless otherwise noted. Specifications in boldface are tested on all production units at final electrical test. Results from these tests are used to calculate outgoing quality levels. All minimum and maximum specifications are guaranteed. Table 1. Parameter OUTPUT VOLTAGE Output Voltage, VO Initial Accuracy, VOERR OUTPUT VOLTAGE DRIFT 1 0°C to 70°C −40°C to +85°C LINE REGULATION 4.5 V ≤ +VIN ≤ 15 V (@ TMIN to TMAX) 15 V ≤ +VIN ≤ 36 V (@ TMIN to TMAX) LOAD REGULATION 0 < IOUT < 10 mA (@ TMIN to TMAX) QUIESCENT CURRENT (@ TMIN to TMAX) POWER DISSIPATION OUTPUT NOISE 0.1 Hz to 10 Hz Spectral Density, 100 Hz CAPACITIVE LOAD LONG-TERM STABILITY SHORT-CIRCUIT CURRENT TO GROUND TEMPERATURE PIN Voltage Output @ 25°C Temperature Sensitivity Output Current Output Resistance TEMPERATURE RANGE Specified Performance Operating Performance 2 1 2 AD680AN/AD680AR Min Typ Max AD680JN/AD680JR Min Typ Max 2.495 −5 −0.20 2.490 −10 −0.40 2.500 2.505 +5 +0.20 10 20 2.500 2.510 +10 +0.40 10 25 25 40 40 40 40 80 80 195 1 8 250 540 596 2 −5 100 100 250 280 1.25 80 80 195 10 8 250 1 50 2.510 +10 +0.40 V mV % 10 25 30 ppm/°C ppm/°C 40 40 40 40 μV/V μV/V μV/V μV/V 100 100 250 280 1.25 μV/mA μV/mA μA μA mW 10 μV p-p nV/√Hz nF ppm/1,000 hr mA 100 100 250 280 1.25 80 80 195 10 8 250 1 660 540 +5 −5 596 2 50 25 25 50 50 660 mV mV/°C μA kΩ +5 12 +85 +85 0 −40 70 +85 Unit 2.500 50 25 25 12 −40 −40 2.490 −10 −0.40 AD680JT Typ Max 40 40 40 40 50 25 25 Min 0 −40 70 +85 °C °C Maximum output voltage drift is guaranteed for all packages. The operating temperature range is defined as the temperature extremes at which the device will still function. Parts may deviate from their specified performance outside their specified temperature range. Rev. H | Page 3 of 12 AD680 ABSOLUTE MAXIMUM RATINGS Table 2. Parameter VIN to Ground Power Dissipation (25°C) Storage Temperature Lead Temperature (Soldering, 10 sec) Package Thermal Resistance θJA (All Packages) Rating 36 V 500 mW −65°C to +125°C 300°C 120°C/W Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the device at these or any other conditions above those indicated in the operational section of this specification is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. OUTPUT PROTECTION Output safe for indefinite short to GND and momentary short to −VIN. ESD CAUTION ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on the human body and test equipment and can discharge without detection. Although this product features proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degradation or loss of functionality. Rev. H | Page 4 of 12 AD680 PIN CONFIGURATIONS AND FUNCTION DESCRIPTIONS TP* 1 8 TP* AD680 7 TP* TOP VIEW (Not to Scale) 6 VOUT 5 NC +VIN 2 TEMP 3 GND 4 00813-003 NC = NO CONNECT * TP DENOTES FACTORY TEST POINT. NO CONNECTIONS SHOULD BE MADE TO THESE PINS. Figure 3. 8-Lead PDIP and 8-Lead SOIC Pin Configuration AD680 BOTTOM VIEW (Not to Scale) 2 1 00813-004 3 +VIN VOUT GND Figure 4. Connection Diagram Table 3. Pin Function Descriptions Pin No. 1, 7, 8 2 3 4 5 6 Mnemonic TP +VIN TEMP GND NC VOUT Descriptions Test Point. A factory test point. No connections are made to these pins. Input Voltage. Temperature Output. Ground. No Connect. Output Voltage. Rev. H | Page 5 of 12 AD680 THEORY OF OPERATION Band gap references are the high performance solution for low supply voltage operation. A typical precision band gap consists of a reference core and buffer amplifier. Based on a new, patented band gap reference design (Figure 5), the AD680 merges the amplifier and the core band gap function to produce a compact, complete precision reference. Central to the device is a high gain amplifier with an intentionally large proportional to absolute temperature (PTAT) input offset. This offset is controlled by the area ratio of the amplifier input pair, Q1 and Q2, and is developed across Resistor R1. Transistor Q12’s base emitter voltage has a complementary to absolute temperature (CTAT) characteristic. Resistor R2 and the parallel combination of Resistor R3 and Resistor R4 “multiply” the PTAT voltage across the R1 resistor. Trimming the R3 and R4 resistors to the proper ratio produces a temperature invariant of 2.5 V at the output. The result is an accurate, stable output voltage accomplished with a minimum number of components. +VIN Reference outputs are frequently required to handle fast transients caused by input switching networks, commonly found in ADCs and measurement instrumentation equipment. Many of the dynamic problems associated with this situation can be minimized with a few simple techniques. Using a series resistor between the reference output and the load tends to “decouple” the reference output from the transient source, or a relatively large capacitor connected from the reference output to ground can serve as a charge storage element to absorb and deliver charge as required by the dynamic load. A 50 nF capacitor is recommended for the AD680 in this case; this is large enough to store the required charge, but small enough not to disrupt the stability of the reference. The 8-lead PDIP and 8-lead SOIC packaged versions of the AD680 also provide a temperature output pin. The voltage on this pin is nominally 596 mV at 25°C. This pin provides an output linearly proportional to temperature with a characteristic of 2 mV/°C. NOISE PERFORMANCE Q9 The noise generated by the AD680 is typically less than 8 μV p-p over the 0.1 Hz to 10 Hz band. Figure 6 shows the 0.1 Hz to 10 Hz noise of a typical AD680. The noise measurement is made with a band-pass filter made of a 1-pole high-pass filter, with a corner frequency at 0.1 Hz, and a 2-pole low-pass filter, with a corner frequency at 12.6 Hz, to create a filter with a 9.922 Hz bandwidth. Q8 Q11 Q3 Q4 VOUT Q5 Q1 1× R1 Q2 R5 R3 8× C1 R2 Q10 1s Q12 100 90 Q6 Q7 TEMP R4 R7 GND 00813-005 R6 5μV Figure 5. Schematic Diagram APPLYING THE AD680 The AD680 is simple to use in virtually all precision reference applications. When power is applied to +VIN and the GND pin is tied to ground, VOUT provides a 2.5 V output. The AD680 typically requires less than 250 μA of current when operating from a supply of 4.5 V to 36 V. To operate the AD680, the +VIN pin must be bypassed to the GND pin with a 0.1 μF capacitor tied as close to the AD680 as possible. Although the ground current for the AD680 is small, typically 195 μA, a direct connection should be made between the AD680 GND pin and the system ground plane. 10 00813-006 0% Figure 6. 0.1 Hz to 10 Hz Noise Noise in a 300 kHz bandwidth is approximately 800 μV p-p. Figure 7 shows the broadband noise of a typical AD680. Rev. H | Page 6 of 12 AD680 500μV In some applications, a varying load may be both resistive and capacitive in nature, or the load may be connected to the AD680 by a long capacitive cable. 50μs 100 90 +VIN 500μV 0.1μF AD680 VOUT VOUT 10 VL 00813-007 0% VOUT 0V 00813-009 249Ω Figure 9. Transient Load Test Circuit Figure 7. Broadband Noise at 300 kHz TURN-ON TIME 2V Upon application of power (cold start), the time required for the output voltage to reach its final value within a specified error band is defined as the turn-on settling time. Two components normally associated with this are the time for the active circuits to settle, and the time for the thermal gradients on the chip to stabilize. The turn-on settling time of the AD680 is about 20 μs to within 0.025% of its final value, as shown in Figure 8. VIN 1mV 5μs VL 90 VOUT 10 10μs 0% 00813-010 5V 50mV 100 100 90 Figure 10. Large Scale Transient Response VOUT 2V 10 5mV 5μs 100 VIN 90 00813-008 0% Figure 8. Turn-On Settling Time VOUT 10 0% 00813-011 The AD680 thermal settling characteristic benefits from its compact design. Once initial turn-on is achieved, the output linearly approaches its final value; the output is typically within 0.01% of its final value after 25 ms. DYNAMIC PERFORMANCE The output stage of the amplifier is designed to provide the AD680 with static and dynamic load regulation superior to less complete references. Figure 9 to Figure 11 display the characteristics of the AD680 output amplifier driving a 0 mA to 10 mA load. Longer settling times result if the reference is forced to sink any transient current. Rev. H | Page 7 of 12 Figure 11. Fine Scale Settling for Transient Load AD680 +VIN AD680 VOUT CL 1000pF VL The AD680 is designed for reference applications where temperature performance is important. Extensive temperature testing and characterization ensure that the device’s performance is maintained over the specified temperature range. VOUT 249Ω VOUT 0V 00813-012 0.1μF TEMPERATURE PERFORMANCE Figure 12. Capacitive Load Transient Response Test Circuit Figure 13 displays the output amplifier characteristics driving a 1,000 pF, 0 mA to 10 mA load. 2V 5mV 5μs 100 VL 90 Some confusion exists in the area of defining and specifying reference voltage error over temperature. Historically, references have been characterized using a maximum deviation per degree centigrade, that is, ppm/°C. However, because of nonlinearities in temperature characteristics that originated in standard Zener references (such as “S” type characteristics), most manufacturers now use a maximum limit error band approach to specify devices. This technique involves measuring the output at three or more different temperatures to specify an output voltage error band. 2.501 SLOPE = TC VOLTS (V) VOUT = VMAX – VMIN (TMAX – TMIN) × 2.5V × 10–6 = 2.501 – 2.498 (85°C – (–40°C)) × 2.5V × 10–6 2.500 = 9.6ppm/°C 2.499 10 2.498 Figure 13. Output Response with Capacitive Load –50 LOAD REGULATION 1mV 80 100 Figure 15 shows a typical output voltage drift for the AD680AN/ AD680AR and illustrates the test methodology. The box in Figure 15 is bounded on the left and right sides by the operating temperature extremes, and on the top and bottom by the maximum and minimum output voltages measured over the operating temperature range. 100μs 100 VL –10 0 20 40 60 TEMPERATURE (°C) Figure 15. Typical AD680AN/AD680AR Temperature Drift Figure 14 depicts the load regulation characteristics of the AD680. 1V –30 90 The maximum height of the box for the appropriate temperature range and device grade is shown in Table 4. Duplication of these results requires a combination of high accuracy and stable temperature control in a test system. Evaluation of the AD680 will produce a curve similar to that in Figure 15, but output readings could vary depending upon the test equipment used. VOUT 10 00813-014 0% Table 4. Maximum Output Change in mV Figure 14. Typical Load Regulation Characteristics Device Grade AD680JN/AD680JR AD680JT AD680AN Rev. H | Page 8 of 12 Maximum Output Change (mV) 0°C to 70°C −40°C to +85°C 4.375 Not applicable 5.250 Not applicable Not applicable 6.250 00813-015 00813-013 0% AD680 TEMPERATURE OUTPUT PIN The 8-lead package versions of the AD680 provide a temperature output pin on Pin 3 of each device. The output of Pin 3 (TEMP) is a voltage that varies linearly with temperature. VTEMP at 25°C is 596 mV, and the temperature coefficient is 2 mV/°C. Figure 16 shows the output of this pin over temperature. The temperature pin has an output resistance of 12 kΩ and is capable of sinking or sourcing currents of up to 5 μA without disturbing the reference output. This enables the TEMP pin to be buffered by many inexpensive operational amplifiers that have bias currents below this value. 760 680 640 600 520 00813-016 440 –50 –40 –30 –20 –10 0 10 20 30 40 TEMPERATURE (°C) 50 60 70 80 The AD7701 is an ADC that is well-suited for the AD680. Figure 18 shows the AD680 used as the reference for this converter. The AD7701 is a 16-bit ADC with on-chip digital filtering intended for the measurement of wide dynamic range and low frequency signals, such as those representing chemical, physical, or biological processes. It contains a charge balancing (Σ–Δ) ADC, a calibration microcontroller with on-chip static RAM, a clock oscillator, and a serial communications port. This entire circuit runs on ±5 V supplies. The power dissipation of the AD7701 is typically 25 mW and, when combined with the power dissipation of the AD680 (1 mW), the entire circuit consumes just 26 mW of power. 560 480 The AD680 has a number of features that make it ideally suited for use with ADCs and DACs. The low supply voltage required makes it possible to use the AD680 with today’s converters that run on 5 V supplies without having to add a higher supply voltage for the reference. The low quiescent current (195 μA), combined with the completeness and accuracy of the AD680, make it ideal for low power applications, such as hand-held, battery-operated meters. +5V ANALOG SUPPLY 90 0.1μF 10μF AD7701 AVDD Figure 16. TEMP Pin Transfer Characteristics VIN DIFFERENTIAL TEMPERATURE TRANSDUCER Figure 17 shows a differential temperature transducer that can be used to measure temperature changes in the environment of the AD680. This circuit operates from a 5 V supply. The temperature-dependent voltage from the TEMP pin of the AD680 is amplified by a factor of 5 to provide wider full-scale range and more current sourcing capability. An exact gain of 5 can be achieved by adjusting the trim potentiometer until the output varies by 10 mV/°C. To minimize resistance changes with temperature, use resistors with low temperature coefficients, such as metal film resistors. VOUT 0.1μF DRDY CS SCLK RANGE SELECT BP/UP CALIBRATE CAL ANALOG INPUT AIN ANALOG GND AGND TEMP 3 AD680 3 + 6 ΔVOUT = 10mV/°C ΔT SERIAL DATA CLKOUT SC1 0.1μF DVSS 10μF Figure 18. Low Power, Low Voltage Supply Reference for the AD7701 16-Bit ADC 4 4 RF 6.98kΩ 1% RBP 100Ω 00813-017 RB 1.69kΩ 1% 0.1μF SERIAL CLOCK CLKIN DGND –5V ANALOG SUPPLY READ (TRANSMIT) 7 OP90 2 – GND SDATA DATA READY SC2 0.1μF AVSS 5V 0.1μF MODE GND VIN 0.1μF SLEEP VREF AD680 5V 2 DVDD Figure 17. Differential Temperature Transducer Rev. H | Page 9 of 12 00813-018 TEMP PIN VOLTAGE (mV) 720 LOW POWER, LOW VOLTAGE REFERENCE FOR DATA CONVERTERS AD680 4.5 V REFERENCE FROM A 5 V SUPPLY The AD680 can be used to provide a low power, 4.5 V reference, as shown in Figure 19. In addition to the AD680, the circuit uses a low power op amp and a transistor in a feedback configuration that provides a regulated 4.5 V output for a power supply voltage as low as 4.7 V. The high quality tantalum 10 μF capacitor (C1) in parallel with the ceramic 0.1 μF capacitor (C2) and the 3.9 Ω resistor (R5) ensure a low output impedance up to approximately 50 MHz (see Figure 19). 4.7V TO 15V CC 3.3μF 2N2907A VIN VOUT AD680 GND –IN 7 3 V+ OUT OP90 2 4 6 V– CF 0.1μF R4 3.57kΩ + C1 10μF C2 0.1μF CHARGER INPUT R5 3.9Ω 0.1μF R3 510kΩ 2 R2 2.5kΩ 1% R1 2kΩ 1% 00813-019 0.1μF +IN The AD680 is ideal for providing a stable, low cost, low power reference voltage in portable equipment power supplies. Figure 20 shows how the AD680 can be used in a voltage regulator that not only has low output noise (as compared to a switch mode design) and low power, but it also has a very fast recovery after current surges. Some caution should be taken in the selection of the output capacitors. Too high an ESR (effective series resistance) could endanger the stability of the circuit. A solid tantalum capacitor, 16 V or higher, and an aluminum electrolytic capacitor, 10 V or higher, are recommended for C1 and C2, respectively. Also, the path from the ground side of C1 and C2 to the ground side of R1 should be kept as short as possible. 6V + LEAD-ACID BATTERY Figure 19. 4.5 V Reference Running from a Single 5 V Supply VIN VOUT 6 AD680 TEMP 3 GND 2 – 7 OP777 3 + 6 IRF9530 4 4 R2 402kΩ 1% R1 402kΩ 1% + C1 + 68μF TANT Figure 20. Voltage Regulator for Portable Equipment Rev. H | Page 10 of 12 C2 1000μF ELECT 00813-020 R3 1kΩ VOLTAGE REGULATOR FOR PORTABLE EQUIPMENT AD680 OUTLINE DIMENSIONS 0.400 (10.16) 0.365 (9.27) 0.355 (9.02) 8 5 1 5.00 (0.1968) 4.80 (0.1890) 8 4.00 (0.1574) 3.80 (0.1497) 1 0.25 (0.0098) 0.10 (0.0040) 0.325 (8.26) 0.310 (7.87) 0.300 (7.62) PIN 1 0.100 (2.54) BSC 5 6.20 (0.2440) 4 5.80 (0.2284) 1.27 (0.0500) BSC 4 0.280 (7.11) 0.250 (6.35) 0.240 (6.10) 1.75 (0.0688) 1.35 (0.0532) 0.51 (0.0201) COPLANARITY SEATING 0.31 (0.0122) 0.10 PLANE 0.50 (0.0196) × 45° 0.25 (0.0099) 8° 0.25 (0.0098) 0° 1.27 (0.0500) 0.40 (0.0157) 0.17 (0.0067) 0.015 (0.38) GAUGE PLANE SEATING PLANE 0.005 (0.13) MIN 0.430 (10.92) MAX COMPLIANT TO JEDEC STANDARDS MS-001-BA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF INCH EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN. CORNER LEADS MAY BE CONFIGURED AS WHOLE OR HALF LEADS. Figure 22. 8-Lead Plastic Dual In-Line Package [PDIP] Narrow Body (N-8) Dimensions shown in inches and (millimeters) 0.050 (1.27) MAX 0.019 (0.482) SQ 0.016 (0.407) 0.165 (4.19) 0.125 (3.18) 0.055 (1.40) 0.045 (1.15) 3 2 0.105 (2.66) 0.095 (2.42) 0.135 (3.43) MIN 0.014 (0.36) 0.010 (0.25) 0.008 (0.20) 0.070 (1.78) 0.060 (1.52) 0.045 (1.14) Figure 21. 8-Lead Standard Small Outline Package [SOIC] Narrow Body (R-8) Dimensions show in millimeters and (inches) 0.205 (5.21) 0.175 (4.45) 0.195 (4.95) 0.130 (3.30) 0.115 (2.92) 0.015 (0.38) MIN 0.022 (0.56) 0.018 (0.46) 0.014 (0.36) COMPLIANT TO JEDEC STANDARDS MS-012AA CONTROLLING DIMENSIONS ARE IN MILLIMETERS; INCH DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF MILLIMETER EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN 0.210 (5.33) 0.170 (4.32) 0.060 (1.52) MAX 0.210 (5.33) MAX 0.150 (3.81) 0.130 (3.30) 0.115 (2.92) 1 0.115 (2.92) 0.080 (2.03) 0.500 (12.70) MIN 0.115 (2.92) 0.080 (2.03) SEATING PLANE BOTTOM VIEW COMPLIANT TO JEDEC STANDARDS TO-226AA CONTROLLING DIMENSIONS ARE IN INCHES; MILLIMETER DIMENSIONS (IN PARENTHESES) ARE ROUNDED-OFF EQUIVALENTS FOR REFERENCE ONLY AND ARE NOT APPROPRIATE FOR USE IN DESIGN Figure 23. 3-Pin Plastic Header-Style Package [TO-92] (T-3) Dimensions shown in inches and (millimeters) Rev. H | Page 11 of 12 AD680 ORDERING GUIDE Model AD680AR AD680AR-REEL AD680AR-REEL7 AD680ARZ 1 AD680ARZ-REEL71 AD680JR AD680JR-REEL7 AD680JRZ1 AD680JRZ-REEL71 AD680AN AD680ANZ1 AD680JN AD680JNZ1 AD680JT AD680JTZ1 1 Output Voltage VO (V) 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 2.5 Initial Accuracy (mV) (%) 5 0.20 5 0.20 5 0.20 5 0.20 5 0.20 10 0.40 10 0.40 10 0.40 10 0.40 5 0.20 5 0.20 10 0.40 10 0.40 10 0.40 10 0.40 Temperature Coefficient (ppm/°C) 20 20 20 20 20 25 25 25 25 20 20 25 25 30 30 Package Description SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC SOIC PDIP PDIP PDIP PDIP TO-92 TO-92 Z = Pb-free part. ©2005 Analog Devices, Inc. All rights reserved. Trademarks and registered trademarks are the property of their respective owners. C00813–0–8/05(H) Rev. H | Page 12 of 12 Package Option R-8 R-8 R-8 R-8 R-8 R-8 R-8 R-8 R-8 N-8 N-8 N-8 N-8 T-3 T-3 Parts per Reel 2,500 1,000 1,000 1,000 1,000 Temperature Range (°C) −40 to +85 −40 to +85 −40 to +85 −40 to +85 −40 to +85 0 to 70 0 to 70 0 to 70 0 to 70 −40 to +85 −40 to +85 0 to 70 0 to 70 0 to 70 0 to 70