1N5614 THRU 1N5622 GLASS PASSIVATED MEDIUM-SWITCHING JUNCTION RECTIFIER Reverse Voltage - 200 to 1000 Volts * D TE FEATURES DO-204AP ♦ High temperature metallurgically bonded construction ♦ 1.0 Ampere operation at TA= 55°C with no thermal runaway ♦ Typical IR less than 0.1µA ♦ Hermetically sealed package ♦ Capable of meeting environmental standards of MIL-S-19500 ♦ High temperature soldering guaranteed: 350°C/10 seconds, 0.375” (9.5mm) lead length, 5 lbs. (2.3kg) tension N TE PA 0.034 (0.86) 0.028 (0.71) DIA. Forward Current - 1.0. Ampere 1.0 (25.4) MIN. 0.240 (6.1) MAX. 0.150 (3.8) 0.100 (2.5) DIA. MECHANICAL DATA 1.0 (25.4) MIN. Dimensions in inches and (millimeters) *Brazed-lead assembly is covered by Patent No. 3,930,306 Case: JEDEC DO-204AP solid glass body Terminals: Solder plated axial leads, solderable per MIL-STD-750, Method 2026 Polarity: Color band denotes cathode end Mounting Position: Any Weight: 0.02 ounce, 0.56 gram MAXIMUM RATINGS AND ELECTRICAL CHARACTERISTICS Ratings at 25°C ambient temperature unless otherwise specified. * Maximum repetitive peak reverse voltage SYMBOLS 1N5614 1N5616 1N5618 1N5620 1N5622 UNITS VRRM 200 400 600 800 1000 Volts VRMS 140 280 420 560 700 Volts * Maximum DC blocking voltage VDC 200 400 600 800 1000 Volts * Minimum reverse breakdown voltage at 50µA VBR 220 440 660 880 1100 Volts Maximum average forward rectified current 0.375” (9.5mm) lead length at TA=55°C I(AV) 1.0 Amp * Peak forward surge current 8.3ms single half sine-wave superimposed on rated load (JEDEC Method) IFSM 50.0 Amps VF 1.2 Volts IR 0.5 25.0 1500 µA Maximum RMS voltage * Maximum instantaneous forward voltage at 1.0A * Maximum DC reverse current at rated DC blocking voltage TA=25°C TA=100°C TA=200°C * Maximum reverse recovery time (NOTE 1) trr Maximum junction capacitance (NOTE 2) CJ Typical thermal resistance (NOTE 3) * Operating junction temperature range * Storage temperature range 35 25 20 15 pF RΘJA 55.0 °C/W TJ -65 to +175 °C TSTG -65 to +200 °C NOTES: (1) Reverse recovery test conditions: IF=0.5A, IR=1.0A, Irr=0.25A (2) Measured at 1.0 MHz and applied reverse voltage of 12 Volts (3) Thermal resistance from junction to ambient at 0.375” (9.5mm) lead length P.C.B. mounted *JEDEC registered values 4/98 µs 2.0 45 RATINGS AND CHARACTERISTIC CURVES 1N5614 THRU 1N5622 FIG. 2 - MAXIMUM NON-REPETITIVE PEAK FORWARD SURGE CURRENT FIG. 1 - FORWARD CURRENT DERATING CURVE 50 60 HZ RESISTIVE OR INDUCTIVE LOAD 0.375" (9.5mm) LEAD LENGTH 0.75 PEAK FORWARD SURGE CURRENT, AMPERES AVERAGE FORWARD RECTIFIED CURRENT, AMPERES 1.0 0.5 0.25 0 25 50 75 100 125 150 40 30 20 10 0 175 TJ=TJ max. 8.3ms SINGLE HALF SINE-WAVE (JEDEC Method) 1 FIG. 3 - TYPICAL INSTANTANEOUS FORWARD CHARACTERISTICS 100 FIG. 4 - TYPICAL REVERSE CHARACTERISTICS 10 10 TJ=150°C INSTANTANEOUS REVERSE CURRENT, MICROAMPERES INSTANTANEOUS FORWARD CURRENT, AMPERES 10 NUMBER OF CYCLES AT 60 HZ AMBIENT TEMPERATURE, °C PULSE WIDTH=300µs 1% DUTY CYCLE 1 TJ=25°C 0.1 TJ=125°C 1 TJ=75°C 0.1 TJ= 25°C 0.01 0 20 40 60 80 PERCENT OF RATED PEAK REVERSE VOLTAGE, % 0.01 0.4 0.6 0.8 1.0 1.2 1.6 1.4 INSTANTANEOUS FORWARD VOLTAGE, VOLTS FIG. 5 - TYPICAL JUNCTION CAPACITANCE JUNCTION CAPACITANCE, pF 30 TJ=25°C f=1.0 MHz Vsig=50mVp-p 10 1 1 10 REVERSE VOLTAGE, VOLTS 100 100