AD ADUC7121

Precision Analog Microcontroller, 12-Bit
Analog I/O, ARM7TDMI MCU
ADuC7121
FEATURES
Software-triggered in-circuit reprogrammability
On-chip peripherals
UART, 2 × I2C and SPI serial I/O
32-pin GPIO port
4× general-purpose timers
Wake-up and watchdog timers (WDT)
Power supply monitor
Vectored interrupt controller for FIQ and IRQ
8 priority levels for each interrupt type
Interrupt on edge or level external pin inputs
Power
Specified for 3 V operation
Active mode: 11 mA at 5 MHz, 40 mA at 41.78 MHz
Packages and temperature range
7 mm × 7 mm 108-ball CSP_BGA
Fully specified for –10°C to +95°C operation
Tools
Low cost QuickStart development system
Full third party support
Analog input/output
9-channel, 12-bit, 1 MSPS ADC
2 differential pairs with input PGA
7 general-purpose inputs (differential or single-ended)
Fully differential and single-ended modes
0 V to VREF analog input range
5 low noise current digital-to-analog converters (IDACs)
250 mA, 200 mA, 80 mA, 45 mA, 20 mA
4 × 12-bit voltage output DACs
On-chip voltage reference
On-chip temperature sensor
Microcontroller
ARM7TDMI core, 16-bit/32-bit RISC architecture
JTAG port supports code download and debug
Clocking options
Trimmed on-chip oscillator (±3%)
External watch crystal
External clock source up to 41.78 MHz
41.78 MHz PLL with programmable divider
Memory
126 kB flash/EE memory, 8 kB SRAM
In-circuit download, JTAG-based debug
APPLICATIONS
Optical modules—tunable laser
FUNCTIONAL BLOCK DIAGRAM
IDAC
IDAC
IDAC
IDAC
BUF
DAC
IDAC0 IDAC1 IDAC2 IDAC3 IDAC4
IDAC
BUF
DAC3
DAC
DAC2
BUF
DAC1
DAC
DAC0
BUF
PADC0N
AGND
DAC
AVDD 3.3V
PGA
PADC0P
ADuC7121
PGA
PLA
PADC1P
ADC4
ADC5
ADC6
1MSPS
12-BIT
SAR ADC
OSC
PLL
POR
PWM
WAKE-UP
TIMER
3× GP
TIMERS
8kB SRAM
(2k × 32-BIT)
LDO
WD
TIMER
VIC
126kB
FLASH
(63k ×
16-BIT)
ARM7
TDMI
UART
JTAG
GPIO
CONTROL
SPI
I2C × 2
ADC7
ADC8
ADC9
ADC10/AINCM
TEMPERATURE
SENSOR
INTERNAL
REFERENCE
IOGND
BUF
VREF_1.2
VREF_2.5
P0.0 TO P0.7
P1.0 TO P1.7
P2.0 TO P2.7
IOVDD
P3.0 TO P3.7
XTALI
XTALO
RST
TDO
TDI
TCK
TMS
TRST
09492-001
PADC1N
Figure 1.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2011 Analog Devices, Inc. All rights reserved.
ADuC7121
TABLE OF CONTENTS
Features .............................................................................................. 1
Other Analog Peripherals.............................................................. 41
Applications....................................................................................... 1
Digital-to-Analog Converters................................................... 41
Functional Block Diagram .............................................................. 1
LDO (Low Dropout Regulator)................................................ 43
Revision History ............................................................................... 3
Current Output DACs (IDAC)................................................. 43
General Description ......................................................................... 4
IDAC MMRs ............................................................................... 45
Specifications..................................................................................... 5
Oscillator and PLL—Power Control........................................ 46
Timing Specifications ................................................................ 10
Digital Peripherals.......................................................................... 50
Absolute Maximum Ratings.......................................................... 15
PWM General Overview........................................................... 50
ESD Caution................................................................................ 15
PWM Convert Start Control .................................................... 52
Pin Configuration and Function Descriptions........................... 16
General-Purpose Input/Output.................................................... 53
Terminology .................................................................................... 20
UART Serial Interface .................................................................... 58
ADC Specifications .................................................................... 20
Baud Rate Generation................................................................ 58
DAC Specifications..................................................................... 20
UART Register Definition......................................................... 58
2
Overview of the ARM7TDMI Core............................................. 21
I C Peripherals ................................................................................ 63
Thumb Mode (T)........................................................................ 21
Serial Clock Generation ............................................................ 63
Long Multiply (M)...................................................................... 21
I2C Bus Addresses....................................................................... 63
EmbeddedICE (I) ....................................................................... 21
I2C Registers ................................................................................ 64
Exceptions ................................................................................... 21
I2C Common Registers .............................................................. 72
ARM Registers ............................................................................ 22
Serial Peripheral Interface ............................................................. 73
Interrupt Latency........................................................................ 22
SPI MISO (Master In, Slave Out) Pin...................................... 73
Memory Organization ................................................................... 23
SPI MOSI (Master Out, Slave In) Pin...................................... 73
Memory Access........................................................................... 23
SPICLK (Serial Clock I/O) Pin................................................. 73
Flash/EE Memory....................................................................... 23
SPI Chip Select Input Pin .......................................................... 73
SRAM ........................................................................................... 23
Configuring External Pins for SPI Functionality................... 73
Memory Mapped Registers ....................................................... 23
SPI Registers................................................................................ 73
Complete MMR Listing............................................................. 24
Programmable Logic Array (PLA)............................................... 76
ADC Circuit Overview .................................................................. 27
PLA MMRs Interface................................................................. 77
ADC Transfer Function............................................................. 27
Interrupt System ............................................................................. 80
Temperature Sensor ................................................................... 29
Normal Interrupt Request (IRQ) ............................................. 80
Converter Operation.................................................................. 31
Fast Interrupt Request (FIQ) .................................................... 81
Driving the Analog Inputs ........................................................ 33
External Interrupts (IRQ0 to IRQ3) ........................................ 85
Band Gap Reference................................................................... 33
Timers .............................................................................................. 87
Power Supply Monitor ............................................................... 34
Timer0—Lifetime Timer........................................................... 87
Nonvolatile Flash/EE Memory ..................................................... 35
Timer1—General-Purpose Timer ........................................... 88
Flash/EE Memory Overview..................................................... 35
Timer2—Wake-Up Timer......................................................... 90
Flash/EE Memory....................................................................... 35
Timer3—Watchdog Timer........................................................ 91
Flash/EE Memory Security ....................................................... 35
Timer4—General-Purpose Timer ........................................... 93
Flash/EE Control Interface........................................................ 36
Outline Dimensions ....................................................................... 95
Execution Time from SRAM and FLASH/EE ........................ 39
Ordering Guide .......................................................................... 95
Reset and Remap ........................................................................ 39
Rev. 0 | Page 2 of 96
ADuC7121
REVISION HISTORY
1/11—Revision 0: Initial Version
Rev. 0 | Page 3 of 96
ADuC7121
GENERAL DESCRIPTION
The ADuC7121 is a fully integrated, 1 MSPS, 12-bit data acquisition system incorporating a high performance multichannel ADC,
16-bit/32-bit MCU, and Flash®/EE memory on a single chip.
The ADC consists of up to seven single-ended inputs and two
extra differential input pairs. The two differential pair inputs
can be routed through a programmable gain amplifier (PGA).
The ADC can operate in single-ended or differential input mode.
The ADC input voltage is 0 V to VREF. A low drift band gap reference, temperature sensor, and voltage comparator complete the
ADC peripheral set.
The ADuC7121 provides five current output digital-to-analog
converters (DACs). The current sources (five current DACs)
feature low noise and low drift high-side current output at
11-bit resolution. The five IDACs are as follows: IDAC0 with
250 mA full-scale (FS) output, IDAC1 with 200 mA FS output,
IDAC2 with 80 mA FS output, IDAC3 with 45 mA FS output,
and IDAC4 with 20 mA FS output.
The ADuC7121 also contains four voltage output digital-to-analog
converters (DACs). The DAC output range is programmable to one
of three voltage ranges.
The devices operate from an on-chip oscillator and a PLL
generating an internal high frequency clock of 41.78 MHz
(UCLK). This clock is routed through a programmable clock
divider from which the MCU core clock operating frequency
is generated. The microcontroller core is an ARM7TDMI®,
16-bit/32-bit RISC machine, which offers up to 41 MIPS peak
performance. Eight kB of SRAM and 126 kB of nonvolatile
Flash/EE memory are provided on chip. The ARM7TDMI core
views all memory and registers as a single linear array.
On-chip factory firmware supports in-circuit serial download
via the I2C serial interface port; nonintrusive emulation is also
supported via the JTAG interface. These features are incorporated
into a low cost QuickStart™ development system supporting this
MicroConverter® family.
The device operates from 3.0 V to 3.6 V, and it is specified over
an industrial temperature range of −10°C to +95°C. The IDACs
are powered from a separate 2 V input power supply. When
operating at 41.78 MHz, the power dissipation is typically
120 mW. The ADuC7121 is available in a 108-ball chip scale
package ball grid array [CSP_BGA].
Rev. 0 | Page 4 of 96
ADuC7121
SPECIFICATIONS
AVDD = IOVDD = 3.0 V to 3.6 V, PVDD = 2.0 V ± 5%, VREF = 2.5 V internal reference, fCORE = 41.78 MHz, TA = −10°C to +95°C, unless
otherwise noted.
Table 1.
Parameter
ADC CHANNEL SPECIFICATIONS
ADC Power-Up Time
DC Accuracy 1, 2
Resolution
Integral Nonlinearity
Min
Typ
Max
5
±0.6
±2
Bits
LSB
±0.5
+1.4/−0.99
LSB
2.5 V internal reference, guaranteed
monotonic
LSB
ADC input is a dc voltage
Internally unbuffered channels
DC Code Distribution
ENDPOINT ERRORS 5
Offset Error
All Channels Except IDACx
Channels
IDACx Channels Only
1
Offset Error Match
Gain Error
Gain Error Match
DYNAMIC PERFORMANCE
±1
±2
±1
Signal-to-Noise Ratio (SNR)
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
Channel-to-Channel Crosstalk
ANALOG INPUT
Input Voltage Ranges
Differential Mode
Single-Ended Mode
69
−78
−75
−80
±2
±5
1
0.15
Leakage Current
Input Capacitance
±0.2
20
20
±5
% of full
scale
LSB
LSB
LSB
dB
dB
dB
dB
VCM 6 ± VREF/2
0 to VREF
AVDD − 1.5
±1
Gain Error4
Gain Drift4
Offset4
Offset Drift4
PADC0x Compliant Range
20
0.15
1000
2
11
3
30
0.1
1
50
6
60
AVDD − 1.2
Rev. 0 | Page 5 of 96
2.5 V internal reference, not production tested
for PADC0 and PADC1 channels
LSB
V
V
V
μA
pF
pF
PADC0x INPUT
Full-Scale Input Range
Input Leakage at PADC0x4
Resolution
Test Conditions/Comments
Eight acquisition clocks and fADC/2
μs
12
Differential Nonlinearity 3, 4
Unit
μA
nA
Bits
%
ppm/°C
nA
pA/°C
V
fIN = 10 kHz sine wave, fSAMPLE = 1 MSPS,
internally unbuffered channels
Includes distortion and noise components
Measured on adjacent channels
See Table 38
Buffer bypassed
Buffer enabled
During ADC acquisition buffer bypassed
During ADC acquisition buffer enabled
28.3 kΩ resistor, PGA gain = 3, acquisition
time = 3.2 μs, pseudo differential mode
0.1% accuracy, 5 ppm external resistor for
current to voltage
PGA offset not included
ADuC7121
Parameter
PADC1 INPUT
Full-Scale Input Range
Input Leakage at PADC1x4
Resolution
Gain Error4
Gain Drift4
Offset4
Offset Drift4
PADC1x-Compliant Range
ON-CHIP VOLTAGE REFERENCE
Output Voltage
Accuracy 7
Reference Temperature Coefficient4
Power Supply Rejection Ratio
Output Impedance
Internal VREF Power-On Time
EXTERNAL REFERENCE INPUT
Input Voltage Range
IDAC CHANNEL SPECIFICATIONS
Voltage Compliance Range
Voltage Compliance Range, IDAC0
REFERENCE CURRENT GENERATOR
Reference Current
Temperature Coefficient
Short-Circuit Detection
Overheat Shutdown
RESOLUTION
FULL-SCALE OUTPUT
IDAC4
IDAC3
IDAC2
IDAC1
IDAC0
Integral Nonlinearity
Noise Current
Full-Scale Error
Full-Scale Error Drift
Zero-Scale Error
IDAC4 Channel
IDAC3 Channel
IDAC2 Channel
IDAC1 Channel
IDAC0 Channel
Settling Time
Signal Bandwidth
Min
Typ
Max
Unit
0.15
700
2
μA
nA
Bits
10.6
11
3
30
0.1
1
50
6
60
AVDD − 1.2
%
ppm/°C
nA
pA/°C
V
Test Conditions/Comments
53.5 kΩ resistor, PGA gain = 3
0.1% accuracy, 5 ppm external resistor for
current to voltage
PGA offset not included
0.47 μF from VREF to AGND
2.5
10
61
10
1
±5
30
V
mV
ppm/°C
dB
Ω
ms
TA = 25°C
TA = 25°C
1.2
AVDD
V
0.4
−0.2
1.6
+1.6 8
V
V
Output voltage compliance
For IDAC0 channel only, linearity not
guaranteed below 0 V
0.38
mA
25
1
135
ppm/°C
mA
°C
Using internal reference, 0.1% 5 ppm 3.16 kΩ
external resistor
Using internal reference
11
Bits
20
45
80
200
250
±2
20
±3
50
mA
mA
mA
mA
mA
LSB
μA
%
ppm/°C
±30
+42/−70
+70/−110
±240
±250
+580/−430
1
20
Rev. 0 | Page 6 of 96
μA
μA
μA
μA
μA
μA
ms
kHz
Junction temperature
Guaranteed monotonic
11-bit mode
RMS value, bandwidth 20 Hz to 10 MHz
VOUT = 1.6 V
Internal VREF, 5 ppm external resistor
Pull-down switch off, VOUT = 0 V
Output range 0.4 V to 1.6 V
Output range −0.2 V to +1.6 V
To 0.1%
ADuC7121
Parameter
LINE REGULATION
Min
Typ
IDAC4
IDAC3
IDAC2
IDAC1
IDAC0
LOAD REGULATION
10
22.5
40
100
750
IDAC4
IDAC3
IDAC2
IDAC1
IDAC0
ACPSRR4
10
22.5
40
100
750
Max
Test Conditions/Comments
Measured with full-scale current load on
current DACs
μA/V
μA/V
μA/V
μA/V
μA/V
Measured with full-scale current load on
current DACs
μA/V
μA/V
μA/V
μA/V
μA/V
% of
fullscale/V
% of
fullscale/V
0.75%
6%
PULL-DOWN
NMOS
Speed4
Voltage DAC (VDAC) CHANNEL
DC Accuracy 9
Resolution
Relative Accuracy
Differential Nonlinearity
Calculated Offset Error
Actual Offset Error
Gain Error 10
Gain Error Mismatch
Settling Time
4
PSRR
DC
1 kHz
10 kHz
100 kHz
DRIFT
Offset Drift4
Gain Error Drift4
SHORT-CIRCUIT CURRENT
ANALOG OUTPUTS
Output Range
DAC AC CHARACTERISTICS
Slew Rate
Voltage Output Settling Time
Digital-to-Analog Glitch Energy
Unit
100
10
12
±2
±0.2
±2
9
±0.15
0.1
10
±1
±0.8
mV
μs
Bits
LSB
LSB
mV
mV
%
%
μs
10 kHz, percentage of each current DAC fullscale current per volt
2.25 MHz, percentage of each current DAC
full-scale current per volt
Drain 40 mA
Triggered by PLA, draw the pin voltage to
10% of its original value
RL = 5 kΩ, CL = 100 pF
Buffered
Guaranteed monotonic
2.5 V internal reference
Measured at Code 0
% of full scale on DAC0
Buffered
−59
−57
−47
−19
−61
dB
dB
dB
dB
10
10
20
0.1
μV/°C
μV/°C
mA
VREF/AVDD − 0.1
2.49
10
±20
Buffer on
V/μs
μs
nV-sec
Rev. 0 | Page 7 of 96
1 LSB change at major carry (where maximum
number of bits simultaneously change in the
DACxDAT register)
ADuC7121
Parameter
TEMPERATURE SENSOR 11
Voltage Output at 25°C
Voltage Temperature Coefficient
Accuracy
Min
POWER SUPPLY MONITOR (PSM)
IOVDD Trip Point Selection
Power Supply Trip Point Accuracy
POWER-ON RESET
WATCHDOG TIMER (WDT)
Timeout Period
FLASH/EE MEMORY
Endurance 12
Data Retention 13
DIGITAL INPUTS
Logic 1 Input Current
Logic 0 Input Current
Input Capacitance
LOGIC INPUTS4
VINL, Input Low Voltage4
VINH, Input High Voltage4
LOGIC OUTPUTS
VOH, Output High Voltage
VOL, Output Low Voltage 14
CRYSTAL INPUTS (XCLKI AND XCLKO)
Logic Inputs, XCLKI Only
VINL, Input Low Voltage
VINH, Input High Voltage
XCLKI Input Capacitance
XCLKO Output Capacitance
INTERNAL OSCILLATOR
MCU CLOCK RATE
From 32 kHz Internal Oscillator
From 32 kHz External Crystal
Using an External Clock
START-UP TIME
At Power-On
From Pause/Nap Mode
From Sleep Mode
From Stop Mode
PROGRAMMABLE LOGIC ARRAY (PLA)
Pin Propagation Delay
Element Propagation Delay
POWER REQUIREMENTS 15, 16
Power Supply Voltage Range
AVDD to AGND and IOVDD to IOGND
Analog Power Supply Currents
AVDD Current
Typ
Max
Unit
707
−1.25
±3
mV
mV/°C
°C
2.79
3.07
±2.5
2.36
V
V
%
V
0
512
10,000
20
MCU in power-down or standby mode before
measurement
Two selectable trip points
Of the selected nominal trip point voltage
sec
Cycles
Years
±0.2
−40
10
Test Conditions/Comments
After user calibration
±1
−60
μA
μA
pF
0.8
V
V
TJ = 85°C
All digital inputs excluding XCLKI and XCLKO
VIH = VDD
VIL = 0 V; except TDI
All logic inputs excluding XCLKI
2.0
2.4
0.4
V
V
±3
V
V
pF
pF
kHz
%
41.78
kHz
MHz
MHz
1.1
1.7
20
20
32.768
326
41.78
0.05
70
24
3.06
1.58
1.7
ms
ns
μs
ms
ms
12
2.5
ns
ns
3.0
3.6
200
Clock divider (CD) = 7
CD = 0
TA = 95°C
Core clock (HCLK) = 41.78 MHz
CD = 0
CD = 7
From input pin to output pin
V
μA
Rev. 0 | Page 8 of 96
All digital outputs excluding XCLKO
ISOURCE = 1.6 mA
ISINK = 1.6 mA
ADC in idle mode
ADuC7121
Parameter
Digital Power Supply Current
IOVDD Current in Normal Mode
IOVDD Current in Pause Mode4
IOVDD Current in Sleep Mode4
Additional Power Supply Currents
ADC
IDAC
DAC
ESD TESTS
HBM Passed Up to
FICDM Passed Up to
Min
Typ
7
11
30
25
100
Max
Unit
Test Conditions/Comments
40
mA
mA
mA
mA
μA
Code executing from Flash/EE
CD = 7
CD = 3
CD = 0 (41.78 MHz clock)
CD = 0 (41.78 MHz clock)
TA = 25°C
2.7
21
250
mA
mA
μA
4
0.5
1
@1 MSPS
All current DACs (IDACs) on
per VDAC
2.5 V reference, TA = 25°C
kV
kV
All ADC channel specifications are guaranteed during normal MicroConverter core operation.
Apply to all ADC input channels.
3
Measured using the factory set default values in the ADC offset register (ADCOF) and gain coefficient register (ADCGN).
4
Not production tested but supported by design and/or characterization data on production release.
5
Measured using the factory set default values in ADCOF and ADCGN with an external AD845 op amp as an input buffer stage as shown in Figure 23. Based on external ADC
system components, the user may need to execute a system calibration to remove external endpoint errors and achieve these specifications (see the ADC section).
6
The input signal can be centered on any dc common-mode voltage (VCM) provided that this value is within the ADC voltage input range specified.
7
VREF calibration and trimming are performed under the following conditions: the core is operating in normal mode CD = 0, the ADC is on, the current DACs are on, and
all VDACs are on. VREF accuracy may vary under other operating conditions.
8
The PVDD_IDAC0 pad voltage must be at least 300 mV greater than the IDAC0 pad voltage. These voltages are measured via the PVDD0 and IDAC0 channels of the
ADC. This allows the IDAC0 pin to be pulled up to 1.7 V provided that this 300 mV differential voltage is maintained between the pads. This may require the
PVDD_IDAC0 being supplied with a voltage greater than 2.0 V. The 2.1 V maximum PVDD_IDACx rating must not be exceeded.
9
DAC linearity is calculated using a reduced code range of 100 to 3995.
10
DAC gain error is calculated using a reduced code range of 100 to internal 2.5 V VREF.
11
Die temperature.
12
Endurance is qualified as per JEDEC Standard 22 Method A117 and measured at −40°C, +25°C, +85°C, and +125°C.
13
Retention lifetime equivalent at junction temperature (TJ) = 85°C as per JEDEC Standard 22 Method A117. Retention lifetime derates with junction temperature.
14
Test carried out with a maximum of eight I/Os set to a low output level.
15
Power supply current consumption is measured in normal, pause, and sleep modes under the following conditions: normal mode using a 3.6 V supply, pause mode
using a 3.6 V supply, and sleep mode using 3.6 V supply.
16
IOVDD power supply current increases typically by 2 mA during a Flash/EE erase cycle.
2
Rev. 0 | Page 9 of 96
ADuC7121
TIMING SPECIFICATIONS
Table 2. I2C Timing in Fast Mode (400 kHz)
Parameter
tL
tH
tSHD
tDSU
tDHD
tRSU
tPSU
tBUF
tR
tF
tSUP
Description
SCL low pulse width
SCL high pulse width
Start condition hold time
Data setup time
Data hold time
Setup time for repeated start
Stop condition setup time
Bus-free time between a stop condition and a start condition
Rise time for both SCL and SDA
Fall time for both SCL and SDA
Pulse width of spike suppressed
Min
200
100
300
100
0
100
100
1.3
Slave
Max
Master
Typ
1360
1140
251,350
740
400
12.51350
400
300
300
50
Unit
ns
ns
ns
ns
ns
ns
ns
μs
ns
ns
ns
200
Table 3. I2C Timing in Standard Mode (100 kHz)
Parameter
tL
tH
tSHD
tDSU
tDHD
tRSU
tPSU
tBUF
tR
tF
Description
SCLx low pulse width
SCLx high pulse width
Start condition hold time
Data setup time
Data hold time
Setup time for repeated start
Stop condition setup time
Bus-free time between a stop condition and a start condition
Rise time for both SCLx and SDAx
Fall time for both SCLx and SDAx
tBUF
Slave
Max
Min
4.7
4.0
4.0
250
0
4.7
4.0
4.7
Unit
μs
ns
μs
ns
μs
μs
μs
μs
μs
ns
3.45
1
300
tSUP
tR
MSB
LSB
tDSU
tSHD
P
S
tF
tDHD
8
2 TO 7
tR
tRSU
tH
1
SCLx
MSB
tDSU
tDHD
tPSU
ACK
tL
9
tSUP
1
S(R)
REPEATED
START
STOP
START
CONDITION CONDITION
Figure 2. I2C-Compatible Interface Timing
Rev. 0 | Page 10 of 96
tF
09492-002
SDAx
ADuC7121
Table 4 SPI Master Mode Timing (Phase Mode = 1)
Parameter
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
Min
Typ
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
Max
25
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
SPICLK
(POLARITY = 0)
tSH
tSL
tSR
SPICLK
(POLARITY = 1)
tDAV
tDF
MOSI
MISO
MSB
MSB IN
tSF
tDR
BIT 6 TO BIT 1
BIT 6 TO BIT 1
tDSU
tDHD
Figure 3. SPI Master Mode Timing (Phase Mode = 1)
Rev. 0 | Page 11 of 96
LSB
LSB IN
09492-003
1
Description
SPICLK low pulse width
SPICLK high pulse width
Data output valid after SPICLK edge
Data input setup time before SPICLK edge 1
Data input hold time after SPICLK edge
Data output fall time
Data output rise time
SPICLK rise time
SPICLK fall time
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADuC7121
Table 5. SPI Master Mode Timing (Phase Mode = 0)
Parameter
tSL
tSH
tDAV
tDOSU
tDSU
tDHD
tDF
tDR
tSR
tSF
Min
Typ
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
25
75
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
SPICLK
(POLARITY = 0)
tSH
tSL
tSR
tSF
SPICLK
(POLARITY = 1)
tDAV
tDOSU
MOSI
MISO
tDF
MSB
tDR
BIT 6 TO BIT 1
MSB IN
BIT 6 TO BIT 1
LSB
LSB IN
tDSU
09492-004
1
Description
SPICLK low pulse width
SPICLK high pulse width
Data output valid after SPICLK edge
Data output setup before SPICLK edge
Data input setup time before SPICLK edge 1
Data input hold time after SPICLK edge
Data output fall time
Data output rise time
SPICLK rise time
SPICLK fall time
tDHD
Figure 4. SPI Master Mode Timing (Phase Mode = 0)
Rev. 0 | Page 12 of 96
ADuC7121
Table 6. SPI Slave Mode Timing (Phase Mode = 1)
Parameter
t CS
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
tSFS
2
Min
200
SPICLK low pulse width 2
SPICLK high pulse width2
Data output valid after SPICLK edge
Data input setup time before SPICLK edge
Data input hold time after SPICLK edge
Data output fall time
Data output rise time
SPICLK rise time
SPICLK fall time
CS high after SPICLK edge
Typ
Max
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
25
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
0
CS is the CS (SPI slave select input) function of the multifunction Pin F3.
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
CS
tSFS
tCS
SPICLK
(POLARITY = 0)
tSH
tSL
tSR
tSF
SPICLK
(POLARITY = 1)
tDAV
MISO
tDF
MSB
MOSI
MSB IN
tDR
BIT 6 TO BIT 1
BIT 6 TO BIT 1
tDSU
LSB
LSB IN
09492-005
1
Description
CS to the SPICLK edge 1
tDHD
Figure 5. SPI Slave Mode Timing (Phase Mode = 1)
Rev. 0 | Page 13 of 96
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ADuC7121
Table 7. SPI Slave Mode Timing (Phase Mode = 0)
Parameter
tCS
Description
CS to SPICLK edge 1
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
tDOCS
tSFS
SPICLK low pulse width 2
SPICLK high pulse width2
Data output valid after SPICLK edge
Data input setup time before SPICLK edge2
Data input hold time after SPICLK edge2
Data output fall time
Data output rise time
SPICLK rise time
SPICLK fall time
Data output valid after CS edge
CS high after SPICLK edge
2
Typ
Max
Unit
ns
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
25
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
25
0
CS is the CS (SPI slave select input) function of the multifunction Pin F3.
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
CS
tCS
tSFS
SPICLK
(POLARITY = 0)
tSH
tSL
tSF
tSR
SPICLK
(POLARITY = 1)
tDAV
tDOCS
tDF
MISO
MOSI
MSB
MSB IN
tDR
BIT 6 TO BIT 1
BIT 6 TO BIT 1
LSB
LSB IN
09492-006
1
Min
200
tDSU
tDHD
Figure 6. SPI Slave Mode Timing (Phase Mode = 0)
Rev. 0 | Page 14 of 96
ADuC7121
ABSOLUTE MAXIMUM RATINGS
AGND = 0 V, TA = 25°C, unless otherwise noted.
Table 8.
Parameter
AVDD to IOVDD
AGND to DGND
IOVDD to IOGND, AVDD to AGND
Digital Input Voltage to IOGND
Digital Output Voltage to IOGND
VREF_2.5 and VREF_1.2 to AGND
Analog Inputs to AGND
Analog Outputs to AGND
Operating Temperature Range, Industrial
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance
108-Ball CSP_BGA
Peak Solder Reflow Temperature
SnPb Assemblies (10 sec to 30 sec)
RoHS-Compliant Assemblies
(20 sec to 40 sec)
Rating
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +6 V
−0.3 V to +5.3 V
−0.3 V to IOVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−10°C to +95°C
−65°C to +150°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating can be applied at any one time.
ESD CAUTION
40°C/W
240°C
260°C
Rev. 0 | Page 15 of 96
ADuC7121
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
9 10 11 12
A
A
B
B
C
C
D
D
E
ADuC7121
F
G
TOP VIEW
G
H
H
J
J
K
K
L
L
M
M
1
2
3
4
5
6
7
8
9 10 11 12
09492-007
E
F
Figure 7. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
C12
D11
Mnemonic
RST
P0.0/SCL0/PLAI[5]
Type 1
I
I/O
E11
P0.1/SDA0/PLAI[4]
I/O
C3
P0.2/SPICLK/ADCBUSY/PLAO[13]
I/O
D3
P0.3/MISO/PLAO[12]/SYNC
I/O
E3
P0.4/MOSI/PLAI[11]/TRIP
I/O
F3
P0.5/CS/PLAI[10]/ADCCONVST
I/O
G3
P0.6/MRST/PLAI[2]
I/O
G10
P0.7/TRST/PLAI[3]
I/O
Description
Reset Input (Active Low).
General-Purpose Input and Output Port 0.0 (P0.0).
I2C Interface Serial Clock for I2C0 (SCL0).
Programmable Logic Array for Input Element 5 (PLAI[5]).
General-Purpose Input and Output Port 0.1 (P0.1).
I2C Interface Serial Data for I2C0 (SDA0).
Programmable Logic Array for Input Element 4 (PLAI[4]).
General-Purpose Input and Output Port 0.2 (P0.2).
SPI Clock (SPICLK).
Status of the ADC (ADCBUSY).
Programmable Logic Array for Output Element 13 (PLAO[13]).
General-Purpose Input and Output Port 0.3 (P0.3).
SPI Master In Slave Out (MISO).
Programmable Logic Array for Output Element 12 (PLAO[12]).
Synchronous Reset (SYNC). Input to reset synchronously the PWM counters using an
external source.
General-Purpose Input and Output Port 0.4 (P0.4).
SPI Master Out Slave In (MOSI).
Programmable Logic Array for Input Element 11 (PLAI[11]).
PWM Trip Interrupt (TRIP). The TRIP function of Pin E3 is the input that allows the PWM
trip interrupt to be triggered.
General-Purpose Input and Output Port 0.5 (P0.5).
SPI Slave Select Input (CS).
Programmable Logic Array for Input Element 10 (PLAI[10]).
ADC Conversions (ADCCONVST). The ADCCONVST function of Pin F3 initiates the ADC
conversions using the PLA or the timer output.
General-Purpose Input and Output Port 0.6 (P0.6).
Power On Reset Output (MRST).
Programmable Logic Array for Input Element 2 (PLAI[2]).
General-Purpose Input and Output Port 0.7 (P0.7).
JTAG Test Port Input, Test Reset (TRST). Debug and download access.
Programmable Logic Array for Input Element 3 (PLAI[3]).
Rev. 0 | Page 16 of 96
ADuC7121
Pin No.
C2
Mnemonic
P1.0/SIN/SCL1/PLAI[7]
Type 1
I/O
D2
P1.1/SOUT/SDA1/PLAI[6]
I/O
C10
P1.2/TDI/PLAO[15]
DI
D10
P1.3/TDO/PLAO[14]
DO
H3
P1.4/PWM1/ECLK/XCLK/PLAI[8]
I/O
J3
P1.5/PWM2/PLAI[9]
I/O
B3
P1.6/PLAO[5]
I/O
B2
P1.7/PLAO[4]
I/O
F11
P2.0/IRQ0/PLAI[13]
I/O
G11
P2.1/IRQ1/PLAI[12]
I/O
H11
P2.2/PLAI[1]
I/O
J11
P2.3/IRQ2/PLAI[14]
I/O
H10
P2.4/PWM5/PLAO[7]
I/O
J10
P2.5/PWM6/PLAO[6]
I/O
C1
P2.6/IRQ3/PLAI[15]
I/O
C9
C4
P2.7/PLAI[0]
P3.0/PLAO[0]
I/O
I/O
C11
P3.1/PLAO[1]
I/O
Description
General-Purpose Input and Output Port 1.0 (P1.0).
Serial Input, Receive Data, UART (SIN).
I2C Interface Serial Clock for I2C1 (SCL1).
Programmable Logic Array for Input Element 7 (PLAI[7]).
General-Purpose Input and Output Port 1.1 (P1.1).
Serial Output, Transmit Data, UART (SOUT).
I2C Interface Serial Data for I2C1 (SDA1).
Programmable Logic Array for Input Element 6 (PLAI[6]).
General-Purpose Input and Output Port 1.2 (P1.2).
JTAG Test Port Input, Test Data In (TDI). The TDI function of Pin C10 is for debug and
download access.
Programmable Logic Array for Output Element 15 (PLAO[15]).
General-Purpose Input and Output Port 1.3 (P1.3).
JTAG Test Port Output, Test Data Out (TDO). The TDO function of Pin D10 is for debug
and download access.
Programmable Logic Array for Output Element 14 (PLAO[14]).
General-Purpose Input and Output Port 1.4 (P1.4).
Pulse-Width Modulator 1 Output (PWM1).
Base System Clock Output (ECLK).
Base System Clock Input (XCLK).
Programmable Logic Array for Input Element 8 (PLAI[8]).
General-Purpose Input and Output Port 1.5 (P1.5).
Pulse-Width Modulator 2 Output (PWM2).
Programmable Logic Array for Input Element 9 (PLAI[9]).
General-Purpose Input and Output Port 1.6 (P1.6).
Programmable Logic Array for Output Element 5 (PLAO[5]).
General-Purpose Input and Output Port 1.7 (P1.7).
Programmable Logic Array for Output Element 4 (PLAO[4]).
General-Purpose Input and Output Port 2.0 (P2.0)/External Interrupt Request 0,
Active High.
Programmable Logic Array for Input Element 13 (PLAI[13]).
General-Purpose Input and Output Port 2.1 (P2.1)
External Interrupt Request 1, Active High (IRQ1).
Programmable Logic Array for Input Element 12 (PLAI[12]).
General-Purpose Input and Output Port 2.2 (P2.2).
Programmable Logic Array for Input Element 1 (PLAI[1]).
General-Purpose Input and Output Port 2.3 (P2.3).
External Interrupt Request 2, Active High (IRQ2).
Programmable Logic Array for Input Element 14 (PLAI[14]).
General-Purpose Input and Output Port 2.4 (P2.4).
Pulse-Width Modulator 5 Output (PWM5).
Programmable Logic Array for Output Element 7 (PLAO[7]).
General-Purpose Input and Output Port 2.5 (P2.5).
Pulse-Width Modulator 6 Output (PWM6).
Programmable Logic Array for Output Element 6 (PLAO[6]).
General-Purpose Input and Output Port 2.6 (P2.6).
External Interrupt Request 3, Active High (IRQ3).
Programmable Logic Array for Input Element 15 (PLAI[15]).
General-Purpose Input and Output Port 2.7 (P2.7).
General-Purpose Input and Output Port 3.0 (P3.0).
Programmable Logic Array for Output Element 0 (PLAO[0]).
General-Purpose Input and Output Port 3.1 (P3.1).
Programmable Logic Array for Output Element 1 (PLAO[1]).
Rev. 0 | Page 17 of 96
ADuC7121
Pin No.
D1
Mnemonic
P3.2/IRQ4/PWM3/PLAO[2]
Type 1
I/O
E1
P3.3/IRQ5/PWM4/PLAO[3]
I/O
E2
P3.4/PLAO[8]
I/O
F2
P3.5/PLAO[9]
I/O
D12
P3.6/PLAO[10]
I/O
E12
P3.7/BM/PLAO[11]
I/O
L8
L5
VREF_2.5
VREF_1.2
AI/O
AI/O
B8
K6
K7
L6
M5
L7
M8
K5
K4
M4
L4
K3
M3
M10
M9
L9
K9
K8
IREF
BUF_VREF1
BUF_VREF2
PADC0P
PADC0N
PADC1P
PADC1N
NC
NC
NC
NC
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10/AINCM
AI/O
AO
AO
AI
AI
AI
AI
NC
NC
NC
NC
AI
AI
AI
AI
AI
AI
AI
K1
K2
J2
L2
M2
L3
M11
L11
L10
K10
K11
K12
B5
C6
DAC0
DAC1
NC
NC
NC
NC
DAC2
NC
NC
NC
NC
DAC3
IDAC4
PVDD_IDAC4
AO
AO
NC
NC
NC
NC
AO
NC
NC
NC
NC
AO
AO
S
Description
General-Purpose Input and Output Port 3.2 (P3.2).
External Interrupt Request 4, Active High (IRQ4).
Pulse-Width Modulator 3 Output (PWM3).
Programmable Logic Array for Output Element 2 (PLAO[2]).
General-Purpose Input and Output Port 3.3 (P3.3).
External Interrupt Request 5, Active High (IRQ5).
Pulse-Width Modulator 4 Output (PWM4).
Programmable Logic Array for Output Element 3 (PLAO[3]).
General-Purpose Input and Output Port 3.4 (P3.4).
Programmable Logic Array for Output Element 8 (PLAO[8]).
General-Purpose Input and Output Port 3.5 (P3.5).
Programmable Logic Array for Output Element 9 (PLAO[9]).
General-Purpose Input and Output Port 3.6 (P3.6).
Programmable Logic Array for Output Element 10 (PLAO[10]).
General-Purpose Input and Output Port 3.7 (P3.7).
Programmable Logic Array for Output Element 11 (PLAO[11]).
2.5 V Reference Output and External 2.5 V Reference Input.
1.2 V Reference Output and External 1.2 V Reference Input. Cannot be used to source
current externally.
Generates Reference Current for IDACs. Set by the external resistor, REXT.
Buffered 2.5 V. The maximum load for BUF_VREF1 is 1.2 mA.
Buffered 2.5 V. The maximum load for BUF_VREF2 is 1.2 mA.
PGA Channel 0+.
PGA Channel 0−.
PGA Channel 1+.
PGA Channel 1−.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
Single-Ended or Differential Analog Input 4.
Single-Ended or Differential Analog Input 5.
Single-Ended or Differential Analog Input 6.
Single-Ended or Differential Analog Input 7.
Single-Ended or Differential Analog Input 8.
Single-Ended or Differential Analog Input 9.
Single-Ended or Differential Analog Input 10 (ADC10).
Common Mode (AINCM). The common-mode function of this pin is for pseudo
differential input.
12-Bit DAC0 Output.
12-Bit DAC1 Output.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
12-Bit DAC2 Output.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
No Connect. Do not connect to this pin.
12-Bit DAC3 Output.
IDAC4 Output. The maximum output for this pin is 20 mA.
2.0 V Power for IDAC4.
Rev. 0 | Page 18 of 96
ADuC7121
Pin No.
A6
A8
A7
C8
A5
C5
B4
A4
A1
A3
A2
B1
A12
A9
A11
A10
B12
B11
B10
B9
M1
M6
L1
M7
M12
B6
L12
C7
B7
Mnemonic
CDAMP_IDAC4
IDAC3
PVDD_IDAC3
CDAMP_IDAC3
IDAC2
PVDD_IDAC2
CDAMP_IDAC2
IDAC1
IDAC1
PVDD_IDAC1
PVDD_IDAC1
CDAMP_IDAC1
IDAC0
IDAC0
PVDD_IDAC0
PVDD_IDAC0
CDAMP_IDAC0
IDAC_TST
PGND
PGND
AGND
AGND
AVDD
AVDD
AGND
AGND
AVDD
AVDD
AVDD_IDAC
Type 1
AI
AO
S
AI
AO
S
AI
AO
AO
S
S
AI
AO
AO
S
S
AI
AI/O
S
S
S
S
S
S
S
S
S
S
S
G1
DVDD
S
G12
DVDD
S
F1
F12
H1
J1
H12
J12
G2
DGND
DGND
IOVDD
IOGND
IOVDD
IOGND
XTALO
S
S
S
S
S
S
DO
H2
XTALI
DI
F10
E10
TCK
TMS
DI
DI
1
Description
Damping Capacitor Pin for IDAC4.
IDAC3 Output. The maximum output for this pin is 45 mA.
2.0 V Power for IDAC3.
Damping Capacitor Pin for IDAC3.
IDAC2 Output. The maximum output for this pin is 80 mA.
2.0 V Power for the IDAC2.
Damping Capacitor for IDAC2.
IDAC1 Output. The maximum output is 200 mA.
IDAC1 Output. The maximum output is 200 mA.
Power for IDAC1.
Power for IDAC1.
Damping Capacitor for IDAC1.
IDAC0 Output. The maximum output is 250 mA.
IDAC0 Output. The maximum output is 250 mA.
Power for IDAC0.
Power for IDAC0.
Damping Capacitor Pin for IDAC0.
IDAC Test Purposes.
Power Ground.
Power Ground.
Analog Ground.
Analog Ground.
Analog Supply (3.3 V).
Analog Supply (3.3 V).
Analog Ground.
Analog Ground.
Analog Supply (3.3 V).
Analog Supply (3.3 V).
Output of 2.5 V LDO regulator for internal IDACs. A 470 nF capacitor to AGND must be
connected to this pin.
Output of 2.6 V On-Chip LDO Regulator. A 470 nF capacitor to DGND must be
connected to this pin.
Output of 2.6 V On-Chip LDO Regulator. A 470 nF capacitor to DGND must be
connected to this pin.
Digital Ground.
Digital Ground.
3.3 V GPIO Supply.
3.3 V GPIO Ground.
3.3 V GPIO Supply.
3.3 V GPIO Ground.
Crystal Oscillator Inverter Output. If an external crystal is not being used, this pin can
remain unconnected.
Crystal Oscillator Inverter Input and Internal Clock Generator Circuits Input. If an
external crystal is not being used, connect this pin to the DGND system ground.
JTAG Test Port Input, Test Clock. Debug and download access.
JTAG Test Port Input, Test Mode Select. Debug and download access.
A is analog, D is digital, I is input, O is output, and S is supply, NC is no connect.
Rev. 0 | Page 19 of 96
ADuC7121
TERMINOLOGY
ADC SPECIFICATIONS
Integral Nonlinearity
Integral nonlinearity (INL) is the maximum deviation of any
code from a straight line passing through the endpoints of the
ADC transfer function. The endpoints of the transfer function
are zero scale, a point ½ LSB below the first code transition, and
full scale, a point ½ LSB above the last code transition.
Differential Nonlinearity
Differential nonlinearity (DNL) is the difference between the
measured and the ideal 1 LSB change between any two adjacent
codes in the ADC.
Offset Error
Offset error is the deviation of the first code transition (0000 . . .
000) to (0000 . . . 001) from the ideal, that is, +½ LSB.
Gain Error
Gain error is the deviation of the last code transition from the
ideal AIN voltage (full scale − 1.5 LSB) after the offset error has
been adjusted out.
Signal to (Noise + Distortion) Ratio
Signal to (noise + distortion) ratio, or SINAD, is the measured
ratio of signal to (noise + distortion) at the output of the ADC.
The signal is the rms amplitude of the fundamental. Noise is the
rms sum of all nonfundamental signals up to half the sampling
frequency (fS/2), excluding dc.
The ratio is dependent on the number of quantization levels in
the digitization process: the more levels there are, the smaller
the quantization noise becomes.
The theoretical SINAD ratio for an ideal N-bit converter with a
sine wave input is given by
Signal to (Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion
Total harmonic distortion (THD) is the ratio of the rms sum of
the harmonics to the fundamental.
DAC SPECIFICATIONS
Relative Accuracy
Otherwise known as endpoint linearity, relative accuracy is a
measure of the maximum deviation from a straight line passing
through the endpoints of the DAC transfer function. It is
measured after adjusting for zero error and full-scale error.
Voltage Output Settling Time
This is the amount of time it takes the output to settle to within
a one LSB level for a full-scale input change.
Rev. 0 | Page 20 of 96
ADuC7121
OVERVIEW OF THE ARM7TDMI CORE
The ARM7™ core is a 32-bit reduced instruction set computer
(RISC). It uses a single 32-bit bus for instruction and data. The
length of the data can be 8 bits, 16 bits, or 32 bits. The length of
the instruction word is 32 bits.
The ARM7TDMI® is an ARM7 core with four additional
features, as follows:
•
•
•
•
EmbeddedICE provides integrated on-chip support for the core.
The EmbeddedICE module contains the breakpoint and watchpoint registers that allow code to be halted for debugging purposes.
These registers are controlled through the JTAG test port.
An ARM® instruction is 32 bits long. The ARM7TDMI processor
supports a second instruction set that has been compressed into
16 bits, called the Thumb® instruction set. Faster execution from
16-bit memory and greater code density can usually be achieved
by using the Thumb instruction set instead of the ARM instruction set, which makes the ARM7TDMI core particularly suitable
for embedded applications.
However, the Thumb mode has two limitations, as follows:
•
Thumb code typically requires more instructions for the
same job. As a result, ARM code is usually best for
maximizing the performance of time-critical code.
The Thumb instruction set does not include some of the
instructions needed for exception handling, which
automatically switches the core to ARM code for exception
handling.
See the ARM7TDMI user guide for details on the core
architecture, the programming model, and both the ARM
and ARM Thumb instruction sets.
The ARM7TDMI instruction set includes four extra instructions that perform 32-bit by 32-bit multiplication with a 64-bit
result, and 32-bit by 32-bit multiplication accumulation (MAC)
with a 64-bit result. These results are achieved in fewer cycles
than required on a standard ARM7 core.
EmbeddedICE (I)
T support for the thumb (16-bit) instruction set
D support for debug
M support for long multiplications
I includes the EmbeddedICE™ module to support
embedded system debugging
THUMB MODE (T)
•
LONG MULTIPLY (M)
When a breakpoint or watchpoint is encountered, the processor
halts and enters debug state. When in a debug state, the processor registers can be inspected, as well as the Flash/EE,
SRAM, and memory mapped registers.
EXCEPTIONS
ARM supports five types of exceptions and a privileged
processing mode for each type. The five types of exceptions are
•
•
•
•
•
Normal interrupt or IRQ. This is provided to service
general-purpose interrupt handling of internal and
external events.
Fast interrupt or FIQ. This is provided to service data
transfers or communication channels with low latency. FIQ
has priority over IRQ.
Memory abort.
Attempted execution of an undefined instruction.
Software interrupt instruction (SWI). This can be used to
make a call to an operating system.
Typically, the programmer defines interrupt as IRQ, but for
higher priority interrupt, that is, faster response time, the
programmer can define interrupt as FIQ.
Rev. 0 | Page 21 of 96
ADuC7121
ARM REGISTERS
INTERRUPT LATENCY
ARM7TDMI has a total of 37 registers: 31 general-purpose
registers and 6 status registers. Each operating mode has
dedicated banked registers.
The worst-case latency for a fast interrupt request (FIQ)
consists of the following:
•
When writing user level programs, 15 general-purpose 32-bit
registers (R0 to R14), the program counter (R15), and the current program status register (CPSR) are usable. The remaining
registers are used for system level programming and exception
handling only.
•
•
•
When an exception occurs, some of the standard registers are
replaced with registers specific to the exception mode. All exception modes have replacement banked registers for the stack
pointer (R13) and the link register (R14) as represented in
Figure 8. The fast interrupt mode has more registers (R8 to R12)
for fast interrupt processing. This means that the interrupt
processing can begin without the need to save or restore these
registers, thus saving critical time in the interrupt handling
process.
R0
At the end of this time, the ARM7TDMI executes the instruction at 0x1C (FIQ interrupt vector address). The maximum
total time is 50 processor cycles, which is just under 1.2 μs in
a system using a continuous 41.78 MHz processor clock.
The maximum interrupt request (IRQ) latency calculation is
similar, but must allow for the fact that FIQ has higher priority
and may delay entry into the IRQ handling routine for an
arbitrary length of time. This time can be reduced to 42 cycles if
the LDM command is not used. Some compilers have an option
to compile without using this command. Another option is to run
the part in Thumb mode wherein the time is reduced to 22 cycles.
USABLE IN USER MODE
R1
SYSTEM MODES ONLY
R2
R3
R4
The minimum latency for FIQ or IRQ interrupts is a total of
five cycles, which consist of the shortest time the request can
take through the synchronizer plus the time to enter the
exception mode.
R5
R6
R7
R8
R9
R10
R11
R12
R13
R14
R8_FIQ
R9_FIQ
R10_FIQ
R11_FIQ
R12_FIQ
R13_FIQ
R14_FIQ
R13_SVC
R14_SVC
R13_ABT
R14_ABT
R13_IRQ
R14_IRQ
Note that the ARM7TDMI always runs in ARM (32-bit) mode
when in privileged modes, for example, when executing
interrupt service routines.
R13_UND
R14_UND
R15 (PC)
USER MODE
SPSR_FIQ
FIQ
MODE
SPSR_SVC
SVC
MODE
SPSR_ABT
ABORT
MODE
SPSR_IRQ
IRQ
MODE
SPSR_UND
09492-008
CPSR
UNDEFINED
MODE
Figure 8. Register Organization
More information relative to the programmer’s model and the
ARM7TDMI core architecture can be found in the following
materials from ARM, Ltd.:
•
•
The longest time the request can take to pass through the
synchronizer.
The time for the longest instruction to complete (the
longest instruction is an LDM) that loads all the registers
including the PC.
The time for the data abort entry.
The time for FIQ entry.
ARM DDI 0029G, ARM7TDMI Technical Reference Manual
ARM DDI 0100, ARM Architecture Reference Manual
Rev. 0 | Page 22 of 96
ADuC7121
MEMORY ORGANIZATION
The ADuC7121 incorporates three separate blocks of memory:
8 kB of SRAM and two 64 kB of on-chip Flash/EE memory.
There are 126 kB of on-chip Flash/EE memory available to the
user, and the remaining 2 kB are reserved for the factoryconfigured boot page. These two blocks are mapped as shown
in Figure 9.
Note that by default, after a reset, the Flash/EE memory is mirrored
at Address 0x00000000. It is possible to remap the SRAM at
Address 0x00000000 by clearing Bit 0 of the REMAP MMR.
This remap function is described in more detail in the Flash/EE
Memory section.
0xFFFFFFFF
MMRs
0xFFFF0000
RESERVED
0x0009F800
FLASH/EE
0x00080000
RESERVED
FLASH/EE MEMORY
The 128 kB of Flash/EE are organized as two banks of 32k × 16
bits. In the first block, 31k × 16 bits is user space and 1k × 16
bits is reserved for the factory configured boot page. The page
size of this Flash/EE memory is 512 bytes.
The second 64 kB block is organized in a similar manner. It is
arranged in 32k × 16 bits, all of which is available as user space.
The 126 kB of Flash/EE are available to the user as code and
nonvolatile data memory. There is no distinction between data
and program because ARM code shares the same space. The real
width of the Flash/EE memory is 16 bits, meaning that in ARM
mode (32-bit instruction), two accesses to the Flash/EE are necessary for each instruction fetch. Therefore, it is recommended that
Thumb mode be used when executing from Flash/EE memory
for optimum access speed. The maximum access speed for the
Flash/EE memory is 41.78 MHz in Thumb mode and 20.89 MHz
in full ARM mode (see the Execution Time from SRAM and
FLASH/EE section).
SRAM
0x00041FFF
SRAM
0x00040000
The 8 kB of SRAM are available to the user, organized as 2k ×
32 bits, that is, 2k words. ARM code can run directly from SRAM
at 41.78 MHz, given that the SRAM array is configured as a 32-bit
wide memory array (see the Execution Time from SRAM and
FLASH/EE section).
RESERVED
REMAPPABLE MEMORY SPACE
(FLASH/EE OR SRAM)
0x00000000
09492-009
0x0001FFFF
Figure 9. Physical Memory Map
MEMORY MAPPED REGISTERS
MEMORY ACCESS
The ARM7 core sees memory as a linear array of 232 byte
locations where the different blocks of memory are mapped as
outlined in Figure 9.
The ADuC7121 memory organization is configured in little
endian format: the least significant byte is located in the lowest
byte address and the most significant byte is located in the
highest byte address.
BIT 0
BYTE 3
.
.
.
BYTE 2
.
.
.
BYTE 1
.
.
.
BYTE 0
.
.
.
B
A
9
8
7
6
5
4
0x00000004
3
2
1
0
0x00000000
0xFFFFFFFF
32 BITS
Figure 10. Little Endian Format
09492-010
BIT 31
The memory mapped register (MMR) space is mapped into the
upper two pages of the memory array and accessed by indirect
addressing through the ARM7 banked registers.
The MMR space provides an interface between the CPU and all
on-chip peripherals. All registers, except the core registers, reside
in the MMR area. All shaded locations shown in Figure 11 are
unoccupied or reserved locations and should not be accessed by
user software. Table 10 through Table 27 provide the complete
MMR memory maps.
The access time reading or writing an MMR depends on the
advanced microcontroller bus architecture (AMBA) bus used
to access the peripheral. The processor has two AMBA buses:
advanced high performance bus (AHB) used for system modules
and advanced peripheral bus (APB) used for a lower performance
peripheral. Access to the AHB is one cycle, and access to the
APB is two cycles. All peripherals on the ADuC7121 are on the
APB except the Flash/EE memory and the GPIOs.
Rev. 0 | Page 23 of 96
ADuC7121
Table 10. IRQ Base Address = 0xFFFF0000
0xFFFF0746
Address
0x0000
0x0004
0x0008
0x000C
0x0010
0x0014
0x001C
0x0020
0x0024
0x0028
0x002C
0x0030
0x0034
0x0038
0x003C
0x0100
0x0104
0x0108
0x010C
0x011C
0x013C
IDAC
0xFFFF0700
0xFFFF05DF
DAC
0xFFFF0580
0xFFFF0524
ADC
0xFFFF0500
0xFFFF0480
0xFFFF0448
0xFFFF0440
0xFFFF0418
0xFFFF0400
0xFFFF0394
0xFFFF0380
0xFFFF0370
0xFFFF0360
0xFFFF0350
0xFFFF0340
0xFFFF0334
0xFFFF0320
BANDGAP
REFERENCE
POWER SUPPLY
MONITOR
PLL AND
OSCILLATOR
CONTROL
GENERAL PURPOSE
TIMER 4
WATCHDOG
TIMER
WAKEUP
TIMER
GENERAL PURPOSE
TIMER
0xFFFF0FBC
PWM
0xFFFF0F80
0xFFFF0EA8
0xFFFF0E80
0xFFFF0E28
0xFFFF0E00
FLASH CONTROL
INTERFACE 1
FLASH CONTROL
INTERFACE 0
0xFFFF0D78
GPIO
0xFFFF0D00
0xFFFF0B54
PLA
0xFFFF0B00
0xFFFF0A14
SPI
0xFFFF0A00
0xFFFF0950
I2C0
TIMER 0
0xFFFF0880
0xFFFF0300
0xFFFF0240
0xFFFF0200
0xFFFF013C
0xFFFF0000
Address
0x0220
0x0230
0x0234
0xFFFF08D0
0xFFFF0318
REMAP AND
SYSTEM CONTROL
Byte
4
4
4
4
4
4
4
4
4
4
4
1
4
1
1
4
4
4
4
4
1
Access Type
R
R
R/W
R/W
W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
W
R/W
R
R
R/W
W
R
R/W
Cycle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Table 11. System Control Base Address = 0xFFFF0200
I2C1
0xFFFF0900
Name
REMAP
RSTSTA
RSTCLR
Byte
1
1
1
Access Type
R/W
R
W
Cycle
1
1
1
0xFFFF082C
UART0
Table 12. Timer Base Address = 0xFFFF0300
0xFFFF0800
09492-011
0xFFFF04A8
0xFFFFFFFF
Name
IRQSTA
IRQSIG
IRQEN
IRQCLR
SWICFG
IRQBASE
IRQVEC
IRQP0
IRQP1
IRQP2
IRQP3
IRQCONN
IRQCONE
IRQCLRE
IRQSTAN
FIQSTA
FIQSIG
FIQEN
FIQCLR
FIQVEC
FIQSTAN
INTERRUPT
CONTROLLER
Figure 11. Memory Mapped Registers
COMPLETE MMR LISTING
Note that the Access Type column corresponds to the access
time reading or writing an MMR, where R is read, W is write,
and R/W is read/write. It depends on the AMBA bus that is
used to access the peripheral. The processor has two AMBA
buses: the advanced high performance bus (AHB ) used for
system modules and the advanced peripheral bus (APB) used
for lower performance peripherals.
Address
0x0300
0x0304
0x0308
0x030C
0x0310
0x0314
0x0320
0x0324
0x0328
0x032C
0x0330
0x0340
0x0344
0x0348
0x034C
0x0360
0x0364
0x0368
0x036C
0x0380
0x0384
0x0388
0x038C
0x0390
Rev. 0 | Page 24 of 96
Name
T0LD
T0VAL0
T0VAL1
T0CON
T0CLRI
T0CAP
T1LD
T1VAL
T1CON
T1CLRI
T1CAP
T2LD
T2VAL
T2CON
T2CLRI
T3LD
T3VAL
T3CON
T3CLRI
T4LD
T4VAL
T4CON
T4CLRI
T4CAP
Byte
2
2
4
4
1
2
4
4
4
1
4
4
4
4
1
2
2
2
1
4
4
4
1
4
Access Type
R/W
R
R
R/W
W
R
R/W
R
R/W
W
R
R/W
R
R/W
W
R/W
R
R/W
W
R/W
R
R/W
W
R
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
ADuC7121
Table 13. PLL Base Address = 0xFFFF0400
Address
0x0404
0x0408
0x040C
0x0410
0x0414
0x0418
Name
POWKEY1
POWCON
POWKEY2
PLLKEY1
PLLCON
PLLKEY2
Byte
2
1
2
2
1
2
Access Type
W
R/W
W
W
R/W
W
Cycle
2
2
2
2
2
2
Table 14. PSM Base Address = 0xFFFF0440
Address
0x0440
Name
PSMCON
Byte
2
Access Type
R/W
Name
REFCON
Byte
1
Access Type
R/W
Table 16. ADC Base Address = 0xFFFF0500
Address
0x0500
0x0504
0x0508
0x050C
0x0510
0x0514
0x0518
0x051C
0x0520
Name
ADCCON
ADCCP
ADCCN
ADCSTA
ADCDAT
ADCRST
ADCGN
ADCOF
PGA_GN
Byte
4
1
1
1
4
1
2
2
2
Access Type
R/W
R/W
R/W
R
R
W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
Table 17. DAC Base Address = 0xFFFF0580
Address
0x0580
0x0584
0x0588
0x058C
0x05B0
0x05B4
0x05D8
0x05DC
Name
DAC0CON
DAC0DAT
DAC1CON
DAC1DAT
DAC2CON
DAC2DAT
DAC3CON
DAC3DAT
Byte
2
4
2
4
2
4
2
4
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
Table 18. IDAC Base Address = 0xFFFF0700
Address
0x0700
0x0704
0x0708
0x070C
0x0710
0x0714
0x0718
0x071C
0x0720
0x0724
0x0728
0x072C
0x0730
Name
IDAC0CON
IDAC0DAT
IDAC0BW
IDAC1CON
IDAC1DAT
IDAC1BW
IDAC2CON
IDAC2DAT
IDAC2BW
IDAC3CON
IDAC3DAT
IDAC3BW
IDAC4CON
Byte
2
4
1
2
4
1
2
4
1
2
4
1
2
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Address
0x0800
0x0804
Cycle
2
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
Name
IDAC4DAT
IDAC4BW
TSDCON
IDACSTA
IDAC0PULLDOWN
Byte
4
1
1
1
1
Access Type
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
Table 19. UART0 Base Address = 0xFFFF0800
Cycle
2
Table 15. Reference Base Address = 0xFFFF0480
Address
0x0480
Address
0x0734
0x0738
0x073C
0x0740
0x0744
0x0808
0x080C
0x0810
0x0814
0X082C
Name
COMTX
COMRX
COMDIV0
COMIEN0
COMDIV1
COMIID0
COMCON0
COMCON1
COMSTA0
COMDIV2
Byte
1
1
1
1
1
1
1
1
1
2
Access Type
W
R
R/W
R/W
R/W
R
R/W
R/W
R
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
Table 20. I2C0 Base Address = 0xFFFF0880
Address
0x0880
0x0884
0x0888
0x088C
0x0890
0x0894
0x0898
0x089C
0x08A0
0x08A4
0x08A8
0x08AC
0x08B0
0x08B4
0x08B8
0x08BC
0x08C0
0x08C4
0x08C8
0x08CC
Name
I2C0MCTL
I2C0MSTA
I2C0MRX
I2C0MTX
I2C0MCNT0
I2C0MCNT1
I2C0ADR0
I2C0ADR1
I2C0SBYTE
I2C0DIV
I2C0SCTL
I2C0SSTA
I2C0SRX
I2C0STX
I2C0ALT
I2C0ID0
I2C0ID1
I2C0ID2
I2C0ID3
I2C0FSTA
Byte
2
2
1
2
2
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
Access Type
R/W
R
R
W
R/W
R
R/W
R/W
R/W
R/W
R/W
R
R
W
R/W
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Table 21. I2C1 Base Address = 0xFFFF0900
Address
0x0900
0x0904
0x0908
0x090C
0x0910
0x0914
0x0918
0x091C
0x0920
Rev. 0 | Page 25 of 96
Name
I2C1MCTL
I2C1MSTA
I2C1MRX
I2C1MTX
I2C1MCNT0
I2C1MCNT1
I2C1ADR0
I2C1ADR1
I2C1SBYTE
Byte
2
2
1
2
2
1
1
1
1
Access Type
R/W
R
R
W
R/W
R
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
ADuC7121
Address
0x0924
0x0928
0x092C
0x0930
0x0934
0x0938
0x093C
0x0940
0x0944
0x0948
0x094C
Name
I2C1DIV
I2C1SCTL
I2C1SSTA
I2C1SRX
I2C1STX
I2C1ALT
I2C1ID0
I2C1ID1
I2C1ID2
I2C1ID3
I2C1FSTA
Byte
2
2
2
1
1
1
1
1
1
1
1
Access Type
R/W
R/W
R
R
W
R/W
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
2
Table 22. SPI Base Address = 0xFFFF0A00
Address
0x0A00
0x0A04
0x0A08
0x0A0C
0x0A10
Name
SPISTA
SPIRX
SPITX
SPIDIV
SPICON
Byte
2
1
1
1
2
Access Type
R
R
W
R/W
R/W
Cycle
2
2
2
2
2
Table 23. PLA Base Address = 0xFFFF0B00
Address
0x0B00
0x0B04
0x0B08
0x0B0C
0x0B10
0x0B14
0x0B18
0x0B1C
0x0B20
0x0B24
0x0B28
0x0B2C
0x0B30
0x0B34
0x0B38
0x0B3C
0x0B40
0x0B44
0x0B48
0x0B4C
0x0B50
0x0B54
Name
PLAELM0
PLAELM1
PLAELM2
PLAELM3
PLAELM4
PLAELM5
PLAELM6
PLAELM7
PLAELM8
PLAELM9
PLAELM10
PLAELM11
PLAELM12
PLAELM13
PLAELM14
PLAELM15
PLACLK
PLAIRQ
PLAADC
PLADIN
PLAOUT
PLALCK
Byte
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
2
4
4
4
1
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Table 24. GPIO Base Address = 0xFFFF0D00
Address
0x0D00
0x0D04
0x0D08
0x0D0C
0x0D20
0x0D24
Name
GP0CON
GP1CON
GP2CON
GP3CON
GP0DAT
GP0SET
Byte
4
4
4
4
4
1
Access Type
R/W
R/W
R/W
R/W
R/W
W
Cycle
1
1
1
1
1
1
Address
0x0D28
0x0D2C
0x0D30
0x0D34
0x0D38
0x0D3C
0x0D40
0x0D44
0x0D48
0x0D4C
0x0D50
0x0D54
0x0D58
0x0D5C
Name
GP0CLR
GP0PAR
GP1DAT
GP1SET
GP1CLR
GP1PAR
GP2DAT
GP2SET
GP2CLR
GP2PAR
GP3DAT
GP3SET
GP3CLR
GP3PAR
Byte
1
4
4
1
1
4
4
1
1
4
4
1
1
4
Access Type
W
R/W
R/W
W
W
R/W
R/W
W
W
R/W
R/W
W
W
R/W
Cycle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Table 25. Flash/EE Block 0 Base Address = 0xFFFF0E00
Address
0x0E00
0x0E04
0x0E08
0x0E0C
0x0E10
0x0E18
0x0E1C
0x0E20
Name
FEE0STA
FEE0MOD
FEE0CON
FEE0DAT
FEE0ADR
FEE0SGN
FEE0PRO
FEE0HID
Byte
1
1
1
2
2
3
4
4
Access Type
R
R/W
R/W
R/W
R/W
R
R/W
R/W
Cycle
1
1
1
1
1
1
1
1
Table 26. Flash/EE Block 1 Base Address = 0xFFFF0E80
Address
0x0E80
0x0E84
0x0E88
0x0E8C
0x0E90
0x0E98
0x0E9C
0x0EA0
Name
FEE1STA
FEE1MOD
FEE1CON
FEE1DAT
FEE1ADR
FEE1SGN
FEE1PRO
FEE1HID
Byte
1
1
1
2
2
3
4
4
Access Type
R
R/W
R/W
R/W
R/W
R
R/W
R/W
Cycle
1
1
1
1
1
1
1
1
Table 27. PWM Base Address= 0xFFFF0F80
Address
0x0F80
0x0F84
0x0F88
0x0F8C
0x0F90
0x0F94
0x0F98
0x0F9C
0x0FA0
0x0FA4
0x0FA8
0x0FAC
0x0FB0
0x0FB4
0x0FB8
Rev. 0 | Page 26 of 96
Name
PWMCON1
PWM1COM1
PWM1COM2
PWM1COM3
PWM1LEN
PWM2COM1
PWM2COM2
PWM2COM3
PWM2LEN
PWM3COM1
PWM3COM2
PWM3COM3
PWM3LEN
PWMCON2
PWMICLR
Byte
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
ADuC7121
ADC CIRCUIT OVERVIEW
The analog-to-digital converter (ADC) incorporates a fast,
multichannel, 12-bit ADC. It can operate from a 3.0 V to 3.6 V
supply and is capable of providing a throughput of up to 1 MSPS
when the clock source is 41.78 MHz. This block provides the
user with a multichannel multiplexer, a differential track-andhold, an on-chip reference, and an ADC.
The ADC consists of a 12-bit successive approximation converter
based around two capacitor DACs. Depending on the input
signal configuration, the ADC can operate in one of the
following three modes:
•
•
•
Fully differential mode, for small and balanced signals.
Single-ended mode, for any single-ended signals.
Pseudo differential mode, for any single-ended signals,
taking advantage of the common-mode rejection offered
by the pseudo differential input.
The converter accepts an analog input range of 0 V to VREF
when operating in single-ended mode or pseudo differential
mode. In fully differential mode, the input signal must be balanced
around a common-mode voltage (VCM) in the range of 0 V to
AVDD and with a maximum amplitude of 2 VREF (see Figure 12).
AVDD
VCM
VCM
2VREF
A voltage output from an on-chip band gap reference proportional to absolute temperature can also be routed through the
front-end ADC multiplexer, effectively creating an additional
ADC channel input. This facilitates an internal temperature sensor
channel, measuring die temperature to an accuracy of ±3°C.
The ADuC7121 is modified in a way that differentiates its ADC
structure from other devices in the ADuC702x family.
The PADC0x and PADC1x inputs connect to a PGA and allow for
a gain from 1 to 5 with 32 steps. The remaining channels can be
configured as single ended or differential. A buffer is provided
before the ADC for measuring internal channels.
ADC TRANSFER FUNCTION
Pseudo Differential and Single-Ended Modes
For both pseudo differential and single-ended modes, the input
range is 0 to VREF. In addition, the output coding is straight binary
in both pseudo differential and single-ended modes with
1 LSB = FS/4096, or 2.5 V/4096 = 0.61 mV, or 610 μV
when VREF = 2.5 V
The ideal code transitions occur midway between successive
integer LSB values (that is, 1/2 LSB, 3/2 LSBs, 5/2 LSBs, …,
FS − 3/2 LSBs). The ideal input/output transfer characteristic is
shown in Figure 13.
2VREF
1111 1111 1111
1111 1111 1101
Figure 12. Examples of Balanced Signals for Fully Differential Mode
A high precision, low drift, and factory calibrated 2.5 V reference
is provided on chip. An external reference can also be connected
as described in the Band Gap Reference section.
OUTPUT CODE
0
1111 1111 1110
2VREF
09492-012
VCM
1111 1111 1100
1LSB =
FS
4096
0000 0000 0011
0000 0000 0010
If the signal has not been deasserted by the time the ADC
conversion is complete, a second conversion begins automatically.
Rev. 0 | Page 27 of 96
0000 0000 0001
0000 0000 0000
0V 1LSB
+FS – 1LSB
VOLTAGE INPUT
Figure 13. ADC Transfer Function in Pseudo Differential Mode or
Single-Ended Mode
09492-013
Single or continuous conversion modes can be initiated in the
software. An external ADCCONVST pin, an output generated from
the on-chip PLA, a Timer0, or a Timer1 overflow can also be
used to generate a repetitive trigger for ADC conversions.
ADuC7121
Fully Differential Mode
The amplitude of the differential signal is the difference between
the signals applied to the VIN+ and VIN− inputs (that is, VIN+ −
VIN−). Therefore, the maximum amplitude of the differential
signal is −VREF to +VREF p-p (2 × VREF). This is regardless of the
common mode (CM). The common mode is the average of the
two signals (VIN+ + VIN−)/2, and is, therefore, the voltage that the
two inputs are centered on, which results in the span of each
input being CM ± VREF/2. This voltage must be set up externally,
and its range varies with VREF (see the Driving the Analog
Inputs section).
The output coding is twos complement in fully differential
mode with
1 LSB = 2 VREF/4096 or 2 × 2.5 V/4096 = 1.22 mV when
VREF = 2.5 V
The output result is ±11 bits, but this is shifted by one bit to the
right. This allows the result in ADCDAT to be declared as a
signed integer when writing C code. The designed code transitions occur midway between successive integer LSB values (that is,
1/2 LSB, 3/2 LSBs, 5/2 LSBs, …, FS − 3/2 LSBs). The ideal input/
output transfer characteristic is shown in Figure 14.
SIGN
BIT
0 1111 1111 1110
0 1111 1111 1100
1LSB =
2 × VREF
4096
OUTPUT CODE
0 1111 1111 1010
0 0000 0000 0001
1 1111 1111 1110
1 0000 0000 0100
09492-014
1 0000 0000 0010
Figure 14. ADC Transfer Function in Differential Mode
PADC0x/PADC1x Pins
The PADC0x and PADC1x pins are differential input channels
to the ADC that each have a programmable gain amplifier
(PGA ) on their front ends.
An external precision resistor converts the current to voltage and
the PGA then amplifies this voltage signal with gain up to 5 by
32 steps. The intention is to compensate the variation of the
detector diode responsivity and normalize optical power read
by the ADC. The external resistor is assumed 0.1% accuracy,
5 ppm. A 1 nF capacitor is shunted with the resistor to suppress
wideband noise. Select the resistor value such that the full-scale
voltage developed on the resistor is less than AVDD − 1.2 V, or
typically 1.8 V.
The PGA is designed to handle 10 mV minimum input. To
minimize noise, bypass the ADC input buffer.
The ADC needs to be placed in pseudo differential mode and
assumes that the negative input is close to ground.
All of the controls are independently set through register bits
for giving maximum flexibility to the user. Typically, users need
to take the following steps (using PADC0x as an example):
1.
2.
3.
4.
5.
6.
7.
8.
Select PADC0N and PADC0P as the PGA input.
Select the PGA output as a MUX input.
Enable the PADC0N pin buffer.
Disable the ADC input buffer.
Set the proper gain value for the PGA.
Bypass the buffer.
Set the ADC to pseudo differential mode.
Start the conversion.
Other Input Channels
ADuC7121 contains seven extra ADC input pins. These pins
can also be configured as differential input pairs or single-ended
inputs, or pseudo differential inputs. The buffer and ADC are
configured independently from the input channel selection. Note
that the input range of the ADC input buffer is from 0.15 V to
AVDD − 0.15 V; if the input signal range exceeds this range, the
input buffer must be bypassed.
The ADuC7121 provides two pins for each thermistor input.
The negative input removes the error of the ground difference.
When selecting the thermistor input, always bypass the negative
side buffer to ensure that the amplifier is not saturated. Configure
the ADC to work in positive pseudo differential mode.
0 0000 0000 0000
1 0000 0000 0000
0LSB
+VREF – 1LSB
–VREF + 1LSB
VOLTAGE INPUT (VIN+ – VIN–)
PADC0N is driven by a buffer to 0.15 V to keep the PGA from
saturation when the input current drops to zero. The buffer can
be disabled by setting the ADCCON Bit 14 so that the PADC0N
pin can be connected to the ground plane as well. This is the
same for the PADC1N pin.
Besides these external inputs, the ADC can also select internal
inputs to monitor three power supplies: IOVDD, PVDD_IDAC0,
and PVDD_IDAC1. The voltage of the five IDAC outputs can
also be monitored by the ADC by selecting the required
channel in Register ADCCP. These internal signals are singleended and can select AGND/PGND/IOGND as the negative
input of the ADC via the ADCCN register.
Note that when monitoring IDAC outputs or PVDD_IDAC0,
PVDD_IDAC1, or IOVDD_MON, the buffer must be enabled
to isolate interference from ADC sampling.
An on-chip diode can also be selected to provide chip temperature
monitoring. The ADC can also select VREF and AGND as inputs
for calibration purposes.
PGA and Input Buffer
The PGA is a one stage, positive gain amplifier that is able to
accept input from 0.1 V to AVDD − 1.2 V, and the output swing
should be at least 2.5 V. The gain of the PGA is from 1 to 5 with
32 linear steps. The PGA cannot be bypassed for the PADC0x
and PADC1x channels.
Rev. 0 | Page 28 of 96
ADuC7121
facilitating an internal temperature sensor channel that
measures die temperature.
The input level for PGA is limited to a maximum value of
AVDD − 1.2 V and minimum value of 0.1 V to ensure that the
amplifiers are not saturated. The input buffer is a rail-to-rail
buffer. It can accept signals from 0.15 to AVDD − 0.15 V. Both
the positive and negative input buffers can be bypassed independently by setting ADCCON Bits[15:14].
The internal temperature sensor is not designed for use as an
absolute ambient temperature calculator. It is intended for use as an
approximate indicator of the temperature of the ADuC7121 die.
The typical temperature coefficient is −0.707 mV/°C.
1250
Once configured via the ADC control and channel selection
registers, the ADC converts the analog input and provides a
12-bit result in the ADC data register.
1200
The top four bits are the sign bits, and the 12-bit result is placed
from Bit 27 to Bit 16, as shown in Figure 15. Again, note that, in
fully differential mode, the result is represented in twos complement format, and when in pseudo differential and single-ended
modes, the result is represented in straight binary format.
SIGN BITS
16 15
1100
1050
0
12-BIT ADC RESULT
1150
1000
–20
Figure 15. ADC Result Format
0
20
40
60
TEMPERATURE (°C)
Timing
80
100
09492-017
27
09492-015
31
ADCDAT (dB)
Typical Operation
Figure 17. ADC Output vs. Temperature
Figure 16 provides details of the ADC timing. Users control the
ADC clock speed and the number of acquisition clocks in the
ADCCON MMR. By default, the acquisition time is eight clocks
and the clock divider is two. The number of additional clocks
(such as bit trial or write) is set to 19, giving a sampling rate of
774 kSPS. For conversion on the temperature sensor, the ADC
acquisition time is automatically set to 16 clocks and the ADC
clock divider is set to 32. When using multiple channels, including
the temperature sensor, the timing settings revert back to the
user-defined settings after reading the temperature sensor channel.
ACQ
BIT TRIAL
WRITE
ADC MMR Interface
The ADC is controlled and configured via a number of MMRs
(see Table 28) that are described in detail in this section.
Table 28. ADC MMRs
Name
ADCCON
ADCCP
ADCCN
ADCSTA
ADC CLOCK
CONVSTART
ADCBUSY
ADCSTA = 0
ADCSTA = 1
ADC INTERRUPT
09492-016
DATA
ADCDAT
ADCDAT
Figure 16. ADC Timing
TEMPERATURE SENSOR
ADCRST
The ADuC7121 provides a voltage output from an on-chip
band gap reference proportional to absolute temperature. This
voltage output can also be routed through the front-end ADC
multiplexer (effectively, an additional ADC channel input),
ADCGN
ADCOF
PGA_GN
Rev. 0 | Page 29 of 96
Description
ADC control register. ADCCON allows the programmer to
enable the ADC peripheral, to select the mode of
operation of the ADC (either single-ended, pseudo
differential, or fully differential mode), and to select the
conversion type (see
Table 29).
ADC positive channel selection register.
ADC negative channel selection register.
ADC status register. ADCSTA indicates when an ADC
conversion result is ready. The ADCSTA register contains
only one bit, ADCREADY (Bit 0), representing the status
of the ADC. This bit is set at the end of an ADC
conversion generating an ADC interrupt. It is cleared
automatically by reading the ADCDAT MMR. When the
ADC is performing a conversion, the status of the ADC
can be read externally via the ADCBusy function of Pin C3.
This pin is high during a conversion. When the
conversion is finished, ADCBusy returns to low. This
information can be available on P0.2 (see the
General-Purpose Input/Output section) if enabled in the
GP0CON register.
ADC data result register. ADCDAT holds the 12-bit ADC
result, as shown in Figure 15.
ADC reset register. ADCRST resets all of the ADC
registers to their default values.
ADC gain calibration register for non-PGA channels.
ADC offset calibration register for all ADC channels.
Gain of PGA_PADC0 and PGA_PADC1.
ADuC7121
Table 29. ADCCON MMR Bit Designations (Address = 0xFFFF0500, Default Value = 0x00000A00)
Bit
31:16
15
Value
0
1
14
0
1
13:11
000
001
010
011
100
101
Description
These bits are reserved.
Positive ADC buffer bypass.
Set to 0 by the user to enable the positive ADC buffer.
Set to 1 by the user to bypass the positive ADC buffer.
Negative ADC buffer bypass.
Set to 0 by the user to enable the negative ADC buffer.
Set to 1 by the user to bypass the negative ADC buffer.
ADC clock speed.
fADC = fCORE Conversion = 19 ADC Clocks + Acquisition Time
000
fADC divide-by-1. This divider is provided to obtain a 1 MSPS ADC with an external clock of <41.78 MHz.
fADC divide-by-2 (default value).
fADC divide-by-4.
fADC divide-by-8.
fADC divide-by-16.
fADC divide-by-32.
ADC acquisition time (number of ADC clocks).
2 clocks.
4 clocks.
8 clocks (default value).
16 clocks.
32 clocks.
64 clocks.
Enable conversion.
Set by the user to 1 to enable conversion mode.
Cleared by the user to 0 to disable conversion mode.
Reserved. The user sets this bit to 0.
ADC power control.
Set by the user to 1 to place the ADC in normal mode. The ADC must be powered up for at least 5 μs
before it converts correctly.
Cleared by the user to 0 to place the ADC in power-down mode.
Conversion mode.
Single-ended mode.
Differential mode.
Pseudo differential mode.
Reserved.
Conversion type.
Enable the ADCCONVST function on Pin F3 as a conversion input.
001
010
011
100
101
110
Other
Enable Timer1 as a conversion input.
Enable Timer0 as a conversion input.
Single software conversion. Automatically set to 000 after conversion.
Continuous software conversion.
PLA conversion.
PWM conversion.
Reserved.
10:8
000
001
010
011
100
101
7
6
5
1
0
4:3
00
01
10
11
2:0
Rev. 0 | Page 30 of 96
ADuC7121
Table 30. ADCCP1 MMR Bit Designations
Table 32. ADCSTA MMR Bit Designations
Bit
7:5
4:0
Bit
0
Value
1
0
0
Value
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
10011
10100
10101
10110
10111
Others
1
Description
Reserved
Positive channel selection bits
PADC0P
PADC1P
Reserved
Reserved
Reserved
Reserved
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10/AINCM
Temperature sensor
DVDD_IDAC0
DVDD_IDAC1
DVDD_IDAC2
DVDD_IDAC3
DVDD_IDAC4
IOVDD_MON
Reserved
Reserved
VREF
AGND
Reserved
Table 33. ADCDAT MMR Bit Designations
Bit
27:16
Value
Description
Holds the ADC result (see Figure 15).
Table 34. ADCRST MMR Bit Designations
Bit
0
Value
1
Description
Set to 1 by the user to reset all the ADC
registers to their default values.
Table 35. PGA_GN MMR Bit Designations1
Bit
11:6
Value2
N/A
5:0
N/A
1
2
Description
Gain of PGA for PADC0 = 1 + 4 ×
(PGA_PADC0_GN/32).
Gain of PGA for PADC1 = 1 + 4 ×
(PGA_PADC1_GN/32).
PGA_PADC0_GN and PGA_PADC1_GN must be ≤ 32.
N/A means not applicable.
Table 36. ADCGN MMR Bit Designations
Bit
11:6
9:0
1
Value1
N/A
N/A
Description
These bits are reserved.
10-bit ADC gain calibration value for non-PGA
channels.
N/A means not applicable.
ADC channel availability depends on part model.
Table 31. ADCCN1 MMR Bit Designations
Bit
7:5
4:0
Value
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
Others
1
Description
Indicates that an ADC conversion is complete. It
is set automatically after an ADC conversion
completes.
Automatically cleared by reading the
ADCDAT MMR.
Description
Reserved
Negative channel selection bits
PADC0N
PADC1N
Reserved
Reserved
Reserved
Reserved
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10/AINCM
VREF
AGND
PGND
IOGND
Reserved
Table 37. ADCOF MMR Bit Designations
Bit
15:10
9:0
1
Value1
N/A
N/A
Description
These bits are reserved.
10-bit ADC offset calibration value.
N/A means not applicable.
CONVERTER OPERATION
The ADC incorporates a successive approximation (SAR)
architecture involving a charge sampled input stage. This
architecture is described for the three different modes of
operation: differential, pseudo differential, and single-ended.
Differential Mode
The ADuC7121 contains a successive approximation ADC
based on two capacitive DACs. Figure 18 and Figure 19 show
simplified schematics of the ADC in acquisition and conversion
phase, respectively. The ADC comprises control logic, a SAR, and
two capacitive DACs. In Figure 18 (the acquisition phase), SW3
is closed and SW1 and SW2 are in Position A. The comparator
is held in a balanced condition, and the sampling capacitor arrays
acquire the differential signal on the input.
ADC channel availability depends on part model.
Rev. 0 | Page 31 of 96
ADuC7121
CAPACITIVE
DAC
CAPACITIVE
DAC
CHANNEL+
AIN0
CS
B
COMPARATOR
A SW1
MUX
CHANNEL– A SW2
AIN11
CS
CHANNEL+
AIN0
SW3
CS
B
COMPARATOR
A SW1
CONTROL
LOGIC
MUX
AIN11
CS
CONTROL
LOGIC
SW3
CHANNEL–
CAPACITIVE
DAC
CAPACITIVE
DAC
Figure 18. ADC Acquisition Phase
Figure 21. ADC in Single-Ended Mode
When the ADC starts a conversion (see Figure 19), SW3 opens,
and SW1 and SW2 move to Position B, causing the comparator
to become unbalanced. Both inputs are disconnected as soon as
the conversion begins. The control logic and the charge redistribution DACs are used to add and subtract fixed amounts of charge
from the sampling capacitor arrays to return the comparator to
a balanced condition. When the comparator is rebalanced, the
conversion is complete.
Analog Input Structure
The control logic generates the ADC output code. The output
impedances of the sources driving the VIN+ input and the VIN−
input must be matched; otherwise, the two inputs have different
settling times, resulting in errors.
The C1 capacitors in Figure 22 are typically 4 pF and can be
primarily attributed to pin capacitance. The resistors are lumped
components made up of the on resistance of the switches. The
value of these resistors is typically about 100 Ω. The C2 capacitors
are the ADC sampling capacitors and have a capacitance of
16 pF typical.
CAPACITIVE
DAC
CHANNEL+
AIN0
CS
B
MUX
CHANNEL– A SW2
AIN11
CS
Figure 22 shows the equivalent circuit of the analog input structure
of the ADC. The four diodes provide ESD protection for the analog
inputs. Take care to ensure that the analog input signals never
exceed the supply rails by more than 300 mV. Voltage in excess
of 300 mV causes these diodes to become forward biased and to
start conducting into the substrate. These diodes can conduct
up to 10 mA without causing irreversible damage to the part.
COMPARATOR
A SW1
SW3
AVDD
CONTROL
LOGIC
D
B
CAPACITIVE
DAC
09492-019
C1
VREF
CS
B
A
AIN11
SW2
CS
SW3
CONTROL
LOGIC
VREF
CHANNEL–
CAPACITIVE
DAC
09492-020
B
VIN–
D
Figure 22. Equivalent Analog Input Circuit Conversion Phase: Switches Open,
Track Phase: Switches Closed
COMPARATOR
A SW1
MUX
R1 C2
09492-022
C1
CAPACITIVE
DAC
CHANNEL+
D
D
Pseudo Differential Mode
In pseudo differential mode, Channel− is linked to the VIN−
input of the ADuC7121, and SW2 switches between A
(Channel−) and B (VREF). The VIN− input must be connected to
ground or a low voltage. The input signal on VIN+ can then vary
from VIN− to VREF + VIN−. Note that VIN− must be chosen so that
VREF + VIN− does not exceed AVDD.
R1 C2
AVDD
Figure 19. ADC Conversion Phase
AIN0
09492-021
VREF
09492-018
B
For ac applications, removing high frequency components from
the analog input signal is recommended with an RC low-pass
filter on the relevant analog input pins. In applications where
harmonic distortion and signal-to-noise ratio are critical, drive
the analog input from a low impedance source. Large source
impedances significantly affect the ac performance of the ADC
and can necessitate the use of an input buffer amplifier. The choice
of the op amp is a function of the particular application. Figure 23
and Figure 24 give an example of an ADC front end.
Figure 20. ADC in Pseudo Differential Mode
ADuC7121
Single-Ended Mode
10Ω
Rev. 0 | Page 32 of 96
0.01µF
09492-023
ADC0
In single-ended mode, SW2 is always connected internally to
ground. The VIN− input pin can be floating. The input signal
range on VIN+ is 0 V to VREF.
Figure 23. Buffering Single-Ended/Pseudo Differential Input
ADuC7121
BAND GAP REFERENCE
ADuC7121
The ADuC7121 provides an on-chip band gap reference of 2.5 V
that can be used for the ADC and for the DAC. This 2.5 V reference is generated from a 1.2 V reference.
ADC0
ADC1
09492-024
VREF
Figure 24. Buffering Differential Inputs
When no amplifier is used to drive the analog input, limit the
source impedance to values lower than 1 kΩ. The maximum
source impedance depends on the amount of total harmonic
distortion (THD) that can be tolerated. The THD increases as
the source impedance increases and the performance degrades.
This internal reference also appears on the VREF pins (VREF_2.5
and VREF_1.2). When using the internal reference, a capacitor of
0.47 μF must be connected between each external VREF pin and
AGND to ensure stability and fast response during ADC
conversions. This reference can also be connected to the external
pin, BUF_VREF2, and used as a reference for other circuits in
the system.
The band gap reference also connects through buffers to the
BUF_VREF1 and the BUF_VREF2 pins. To damp the noise,
connect a minimum of 0.1 μF capacitor to these pins. The band
gap reference interface consists of an 8-bit REFCON MMR,
described in Table 39.
DRIVING THE ANALOG INPUTS
An internal or external reference can be used for the ADC.
In differential mode of operation, there are restrictions on
the common-mode input signal (VCM). These restrictions are
dependent on the reference value and supply voltage used
to ensure that the signal remains within the supply rails.
Table 38 gives some calculated VCM minimum and VCM
maximum values.
Table 38. VCM Ranges
AVDD
3.3 V
3.0 V
VREF
2.5 V
2.048 V
1.25 V
2.5 V
2.048 V
1.25 V
VCM Min
1.25 V
1.024 V
0.75 V
1.25 V
1.024 V
0.75 V
VCM Max
2.05 V
2.276 V
2.55 V
1.75 V
1.976 V
2.25 V
Signal Peak-to-Peak
2.5 V
2.048 V
1.25 V
2.5 V
2.048 V
1.25 V
Table 39. REFCON MMR Bit Designations (Address = 0xFFFF0480, Default Value = 0x01)
Bit
7:1
2
1
0
Description
Reserved.
BUF_VREF1/BUF_VREF2 is driven from the internal 2.5 V reference when set to 1.
Internal 2.5 V reference output enable.
Set by the user to connect the internal 2.5 V reference to the VREF_2.5 pin.
Cleared by the user to disconnect the reference from the VREF_2.5 pin. The VREF_2.5 pin should also be cleared to connect an external
reference source to it.
Internal 1.2 V reference output enable.
Set by the user to connect the internal 1.2 V reference to the VREF_1.2 pin.
Cleared by the user to disconnect the reference from the VREF_1.2 pin.
Rev. 0 | Page 33 of 96
ADuC7121
POWER SUPPLY MONITOR
The power supply monitor on the ADuC7121 indicates when
the IOVDD supply pin drops below one of two supply trip
points. The monitor function is controlled via the PSMCON
register. If enabled in the IRQEN or FIQEN register, the monitor
interrupts the core using the PSMI bit in the PSMCON MMR.
This bit is cleared immediately after CMP goes high. Note that
if the interrupt generated is exited before CMP goes high
(IOVDD supply voltage is above the trip point), no further
interrupts are generated until CMP returns high. The user
needs to ensure that the code execution remains within the ISR
until CMP returns high.
This monitor function allows the user to save working registers
to avoid possible data loss due to low supply or brownout conditions. It also ensures that normal code execution does not
resume until a safe supply level has been established.
The PSM does not operate correctly when using JTAG debug;
therefore, disable PSM while in JTAG debug mode.
Table 40. PSMCON MMR Bit Designations (Address = 0xFFFF0440, Default Value = 0x0008)
Bit
15:4
3
Name
Reserved
CMP
2
TP
1
PSMEN
0
PSMI
Description
These bits are reserved.
Comparator bit. This is a read-only bit that directly reflects the state of the comparator.
Read 1 indicates that the IOVDD supply is above its selected trip point or the PSM is in power-down mode.
Read 0 indicates the IOVDD supply is below its selected trip point. Set this bit before leaving the interrupt
service routine.
Trip point selection bit.
0 = 2.79 V.
1 = 3.07 V.
Power supply monitor enable bit.
Set to 1 by the user to enable the power supply monitor circuit.
Cleared to 0 by the user to disable the power supply monitor circuit.
Power supply monitor interrupt bit. This bit is set high by the MicroConverter if CMP is low, indicating low
I/O supply. The PSMI bit can be used to interrupt the processor. When CMP returns high, the PSMI bit can
be cleared by writing a 1 to this location. A write of 0 has no effect. There is no timeout delay. PSMI can be
cleared immediately after CMP goes high.
Rev. 0 | Page 34 of 96
ADuC7121
NONVOLATILE FLASH/EE MEMORY
FLASH/EE MEMORY OVERVIEW
The ADuC7121 incorporates Flash/EE memory technology on
chip to provide the user with nonvolatile, in circuit reprogrammable memory space.
Similar to EEPROM, flash memory can be programmed in system
at a byte level, although it must first be erased. The erase is
performed in page blocks. As a result, flash memory is often
(and more correctly) referred to as Flash/EE memory.
Overall, Flash/EE memory represents a step closer to the ideal
memory device that includes no volatility, in circuit programmability, high density, and low cost. Incorporated in the
ADuC7121, Flash/EE memory technology allows the user
to update program code space in circuit, without the need
to replace one time programmable (OTP) devices at remote
operating nodes.
industrial temperature range of –10° to +95°C. The results allow
the specification of a minimum endurance figure over a supply
temperature of 10,000 cycles.
Retention quantifies the ability of the Flash/EE memory to
retain its programmed data over time. Again, the parts are
qualified in accordance with the formal JEDEC Retention
Lifetime Specification A117 at a specific junction temperature
(TJ = 85°C). As part of this qualification procedure, the
Flash/EE memory is cycled to its specified endurance limit,
described previously, before data retention is characterized.
This means that the Flash/EE memory is guaranteed to retain
its data for its fully specified retention lifetime every time the
Flash/EE memory is reprogrammed. Note, too, that retention
lifetime, based on activation energy of 0.6 eV, derates with
TJ, as shown in Figure 25.
FLASH/EE MEMORY
600
RETENTION (Years)
The ADuC7121 contains two 64 kB arrays of Flash/EE memory.
In the first block, the lower 62 kB is available to the user and the
upper 2 kB of this Flash/EE memory array program contain
permanently embedded firmware, allowing in circuit serial download. The 2 kB of embedded firmware also contain a power-on
configuration routine that downloads factory calibrated coefficients
to the various calibrated peripherals (band gap references and
so forth). This 2 kB embedded firmware is hidden from user code.
It is not possible for the user to read, write, or erase this page.
Flash/EE Memory Reliability
The Flash/EE memory arrays on the ADuC7121 are fully
qualified for two key Flash/EE memory characteristics:
Flash/EE memory cycling endurance and Flash/EE memory
data retention.
Endurance quantifies the ability of the Flash/EE memory to be
cycled through many program, read, and erase cycles. A single
endurance cycle is composed of four independent, sequential
events, defined as follows:
1.
2.
3.
4.
Initial page erase sequence
Read/verify sequence a single Flash/EE
Byte program sequence memory
Second read/verify sequence endurance cycle
300
0
30
40
55
70
85
100
125
JUNCTION TEMPERATURE (°C)
135
150
09492-025
150
In the second block, all 64 kB of Flash/EE memory are available
to the user.
The 126 kB of Flash/EE memory can be programmed in circuit
using the serial download mode or the JTAG mode.
450
Figure 25. Flash/EE Memory Data Retention
Serial Downloading (In-Circuit Programming)
The ADuC7121 facilitates code download via the I2C serial
port. The ADuC7121 enters serial download mode after a reset
or power cycle if the BM function of the P3.7/BM/PLAO[11]
pin is pulled low through an external 1 kΩ resistor. This is
combined with the state of Address 0x00014 in the flash. If this
address is 0xFFFFFFFF and BM is pulled low, the part enters
download mode; if this address contains any other value, user
code is executed. When in serial download mode, the user can
download code to the full 126 kB of Flash/EE memory while the
device is in circuit in its target application hardware. A PC serial
download executable and hardware dongle are provided as part of
the development system for serial downloads via the I2C port.
JTAG Access
In reliability qualification, every half word (16-bit wide) location
of the three pages (top, middle, and bottom) in the Flash/EE
memory is cycled 10,000 times from 0x0000 to 0xFFFF.
As indicated in the Specifications section, the Flash/EE memory
endurance qualification is carried out in accordance with
JEDEC Retention Lifetime Specification A117 over the
The JTAG protocol uses the on-chip JTAG interface to facilitate
code download and debug.
FLASH/EE MEMORY SECURITY
The 126 kB of Flash/EE memory available to the user can be
read and write protected. Bit 31 of the FEE0PRO/FEE0HID MMR
protects the 126 kB from being read through JTAG and also in
I2C programming mode. The other 31 bits of this register protect
Rev. 0 | Page 35 of 96
ADuC7121
writing to the Flash/EE memory; each bit protects four pages, that
is, 2 kB. Write protection is activated for all access types. FEE1PRO
and FEE1HID similarly protect the second 64 kB block. All 32 bits
of this are used to protect four pages at a time.
FLASH/EE CONTROL INTERFACE
Three Levels of Protection
Name:
FEE0DAT
Protection can be set and removed by writing directly into the
FEExHID MMR. This protection does not remain after reset.
Address:
0xFFFF0E0C
Default value:
0xXXXX
Access:
Read and write
Protection can be set by writing into the FEExPRO MMR. It
takes effect only after a save protection command (0x0C) and
a reset. The FEExPRO MMR is protected by a key to avoid direct
access. The key is saved one time only and must be reentered to
modify FEExPRO. A mass erase sets the key back to 0xFFFF but
also erases all the user code.
FEE0DAT Register
FEE0DAT is a 16-bit data register.
FEE0ADR Register
FEE0ADR is a 16-bit address register.
The Flash/EE memory can be permanently protected by using
the FEEPRO MMR and a particular value of the 0xDEADDEAD
key. Entering the key again to modify the FEExPRO register is
not allowed.
Name:
FEE0ADR
Address:
0xFFFF0E10
Default value:
0x0000
Sequence to Write the Key to Protection Registers
Access:
Read and write
1.
2.
3.
4.
5.
Write the bit in FEExPRO corresponding to the page to be
protected.
Enable key protection by setting Bit 6 of FEExMOD (Bit 5
must equal 0).
Write a 32-bit key in FEExADR, FEExDAT.
Run the write key command 0x0C in FEExCON; wait for
the read to be successful by monitoring FEExSTA.
Reset the part.
To remove or modify the protection, the same sequence is used
with a modified value of FEExPRO. If the key chosen is the value
0xDEAD, then the memory protection cannot be removed. Only
a mass erase unprotects the part, but it also erases all user code.
The sequence to write the key is shown in the following example;
this protects writing Page 4 to Page 7 of the Flash/EE memory:
FEE0PRO=0xFFFFFFFD; //Protect Page 4 to Page 7
FEE0SGN Register
FEE0SGN is a 24-bit code signature.
Name:
FEE0SGN
Address:
0xFFFF0E18
Default value:
0xFFFFFF
Access:
Read only
FEE0PRO Register
FEE0PRO provides protection following subsequent reset MMR.
It requires a software key (see Table 41).
Name:
FEE0PRO
FEE0MOD=0x48;
//Write key enable
Address:
0xFFFF0E1C
FEE0ADR=0x1234;
//16-bit key value
Default value:
0x00000000
FEE0DAT=0x5678;
//16-bit key value
FEE0CON= 0x0C;
//Write key command
Access:
Read and write
Follow the same sequence to permanently protect the part with
FEExADR = 0xDEAD and FEExDAT = 0xDEAD.
FEE0HID Register
FEE0HID provides immediate protection MMR. It does not
require any software keys (see Table 41).
Name:
FEE0HID
Address:
0xFFFF0E20
Default value:
0xFFFFFFFF
Access:
Read and write.
Rev. 0 | Page 36 of 96
ADuC7121
Table 41. FEE0PRO and FEE0HID MMR Bit Designations
FEE1HID Register
Bit
31
FEE1HID provides immediate protection MMR. It does not
require any software keys (see Table 42).
30:0
Description
Read protection.
Cleared by the user to protect Block 0.
Set by the user to allow reading Block 0.
Write protection for Page 123 to Page 120, for Page 119
to Page 116, and for Page 0 to Page 3.
Cleared by the user to protect the pages in writing.
Set by the user to allow writing the pages.
Command Sequence for Executing a Mass Erase
FEE0DAT
FEE0ADR
FEE0MOD
FEE0CON
=
=
=
=
0x3CFF;
0xFFC3;
FEE0MOD|0x8; //Erase key enable
0x06;
//Mass erase command
Name:
FEEHID
Address:
0xFFFF0EA0
Default value:
0xFFFFFFFF
Access:
Read and write
Table 42. FEE1PRO and FEE1HID MMR Bit Designations
Bit
31
FEE1DAT Register
FEE1DAT is a 16-bit data register.
Name:
FEE1DAT
Address:
0xFFFF0E8C
Default value:
0xXXXX
Access:
Read and write
30
29:0
Description
Read protection.
Cleared by the user to protect Block 1.
Set by the user to allow reading Block 1.
Write protection for Page 127 to Page 120.
Cleared by the user to protect the pages in writing.
Set by the user to allow writing the pages.
Write protection for Page 119 to Page 116 and for Page 0
to Page 3.
Cleared by the user to protect the pages in writing.
Set by the user to allow writing the pages.
FEE0STA Register
FEE1ADR Register
FEE1ADR is a 16-bit address register.
Name:
FEE1ADR
Address:
0xFFFF0E90
Default value:
0x0000
Access:
Read and write
FEE1SGN is a 24-bit code signature.
FEE1SGN
Address:
0xFFFF0E98
Default value:
0xFFFFFF
Access:
Read only
FEE1PRO provides protection following subsequent reset MMR.
It requires a software key (see Table 42).
FEE1PRO
Address:
0xFFFF0E9C
Default value:
0x00000000
Access:
Read and write
Address:
0xFFFF0E00
Default value:
0x0000
Access:
Read and write
Name:
FEE1STA
Address:
0xFFFF0E80
Default value:
0x0000
Access:
Read and write
Table 43. FEExSTA MMR Bit Designations
FEE1PRO Register
Name:
FEE0STA
FEE1STA Register
FEE1SGN Register
Name:
Name:
Bit
15:6
5
4
3
2
Rev. 0 | Page 37 of 96
Description
Reserved.
Reserved.
Reserved.
Flash/EE interrupt status bit.
Set automatically when an interrupt occurs, that is,
when a command is complete and the Flash/EE
interrupt enable bit in the FEExMOD register is set.
Cleared when reading FEExSTA register.
Flash/EE controller busy.
Set automatically when the controller is busy.
Cleared automatically when the controller is not busy.
ADuC7121
Bit
1
0
Description
Command fail.
Set automatically when a command completes
unsuccessfully.
Cleared automatically when reading FEExSTA register.
Command complete.
Set by MicroConverter when a command is complete.
Cleared automatically when reading FEExSTA register.
FEE0MOD Register
Table 44. FEExMOD MMR Bit Designations
Bit
7:5
4
3
Name:
FEE0MOD
Address:
0xFFFF0E04
Default value:
0x80
Access:
Read and write
2
1:0
Description
Reserved. These bits are always set to 0 except when
writing keys. See the Sequence to Write the Key to
Protection Registers section for details.
Flash/EE interrupt enable.
Set by the user to enable the Flash/EE interrupt. The
interrupt occurs when a command is complete.
Cleared by the user to disable the Flash/EE interrupt.
Erase/write command protection.
Set by the user to enable the erase and write commands.
Cleared to protect the Flash/EE memory against
erase/write command.
Reserved. The user must set this bit to 0.
Flash/EE wait states. Both Flash/EE blocks must have the
same wait state value for any change to take effect.
FEE0CON Register
FEE1MOD Register
Name:
FEE1MOD
Address:
0xFFFF0E84
Default value:
0x80
Access:
Read and write
Name:
FEE0CON
Address:
0xFFFF0E08
Default value:
0x00
Access:
Read and write
FEE1CON Register
Name:
FEE1CON
Address:
0xFFFF0E88
Default value:
0x00
Access:
Read and write
Table 45. Command Codes in FEExCON
Code
0x00 1
0x011
0x021
0x031
Command
Null
Single read
Single write
Erase/write
0x041
Single verify
0x051
0x061
Single erase
Mass erase
0x07
0x08
0x09
0x0A
0x0B
0x0C
Reserved
Reserved
Reserved
Reserved
Signature
Protect
0x0D
0x0E
0x0F
Reserved
Reserved
Ping
1
Description
Idle state.
Load FEExDAT with the 16-bit data indexed by FEExADR.
Write FEExDAT at the address pointed by FEExADR. This operation takes 50 μs.
Erase the page indexed by FEExADR and write FEExDAT at the location pointed by FEExADR. This operation takes 20
ms.
Compare the contents of the location pointed by FEExADR to the data in FEExDAT. The result of the comparison is
returned in FEExSTA Bit 1.
Erase the page indexed by FEExADR.
Erase user space. The 2 kB of kernel are protected in Block 0. This operation takes 2.48 sec. To prevent accidental
execution, a command sequence is required to execute this instruction.
Reserved.
Reserved.
Reserved.
Reserved.
Gives a signature of the 64 kB of Flash/EE in the 24-bit FEExSIGN MMR. This operation takes 32,778 clock cycles.
This command can be run only once. The value of FEExPRO is saved and can be removed only with a mass erase (0x06)
or with the key.
Reserved.
Reserved.
No operation, interrupt generated.
The FEExCON register always reads 0x07 immediately after execution of any of these commands.
Rev. 0 | Page 38 of 96
ADuC7121
EXECUTION TIME FROM SRAM AND FLASH/EE
RESET AND REMAP
This section describes SRAM and Flash/EE access times during
execution for applications where execution time is critical.
The ARM exception vectors are situated at the bottom of the
memory array, from Address 0x00000000 to Address 0x00000020,
as shown in Figure 26.
Execution from SRAM
Fetching instructions from SRAM takes one clock cycle because
the access time of the SRAM is 2 ns and a clock cycle is 22 ns
minimum. However, if the instruction involves reading or
writing data to memory, one extra cycle must be added if the
data is in SRAM (or three cycles if the data is in Flash/EE), one
cycle to execute the instruction, and two cycles to retrieve the
32-bit data from Flash/EE. A control flow instruction, such as a
branch instruction, takes one cycle to fetch, but it also takes two
cycles to fill the pipeline with the new instructions.
In ARM mode, where instructions are 32 bits, two cycles are
needed to fetch any instruction when CD = 0. In Thumb mode,
where instructions are 16 bits, one cycle is needed to fetch any
instruction.
Timing is identical in both modes when executing instructions
that involve using the Flash/EE for data memory. If the instruction
to be executed is a control flow instruction, an extra cycle is
needed to decode the new address of the program counter and
then four cycles are needed to fill the pipeline. A data processing
instruction involving only core registers does not require any
extra clock cycles, but if it involves data in Flash/EE, one
additional clock cycle is needed to decode the address of the
data and two additional cycles are needed to obtain the 32-bit
data from Flash/EE. An extra cycle must also be added before
fetching another instruction. Data transfer instructions are
more complex and are summarized in Table 46.
Table 46. Execution Cycles in ARM/Thumb Mode
Dead
Time
1
1
N
1
1
N
0x0008FFFF
FLASH/EE
INTERRUPT
SERVICE ROUTINES
0x00080000
Data Access
2
1
2×N
2 × 20 μs
20 μs
2 × N × 20 μs
Dead
Time
1
1
N
1
1
N
SRAM
INTERRUPT
SERVICE ROUTINES
0x00040000
MIRROR SPACE
ARM EXCEPTION
VECTOR ADDRESSES
0x00000020
0x00000000
0x00000000
Figure 26. Remap for Exception Execution
By default and after any reset, the Flash/EE is mirrored at the
bottom of the memory array. The remap function allows the
programmer to mirror the SRAM at the bottom of the memory
array, facilitating execution of exception routines from SRAM
instead of from Flash/EE. This means exceptions are executed
twice as fast, with the exception being executed in ARM mode
(32 bits), and the SRAM being 32 bits wide instead of being
16-bit wide Flash/EE memory.
Remap Operation
When a reset occurs on the ADuC7121, execution starts automatically in factory programmed internal configuration code.
This kernel is hidden and cannot be accessed by user code.
If the ADuC7121 is in normal mode (the P3.7/BM/PLAO[11] pin
is high), it executes the power-on configuration routine of the
kernel and then jumps to the Reset Vector Address 0x00000000 to
execute the user’s reset exception routine. Because the Flash/EE is
mirrored at the bottom of the memory array at reset, the reset
interrupt routine must always be written in Flash/EE.
The remap is performed from Flash/EE by setting Bit 0 of the
remap register. Precautions must be taken to execute this
command from Flash/EE (above Address 0x00080020) and not
from the bottom of the array because this, the defined memory
space, is replaced by the SRAM.
With 1 < N ≤ 16, N is the number of bytes of data to load or
store in the multiple load/store instruction. The SWAP instruction
combines an LD and STR instruction with only one fetch,
giving a total of eight cycles plus 40 μs.
09492-026
Because the Flash/EE width is 16 bits and access time for 16-bit
words is 23 ns, execution from Flash/EE cannot be accomplished
in one cycle (as can be done from SRAM when the CD bit = 0). In
addition, some dead times are needed before accessing data for
any value of CD bits.
Fetch
Cycles
2/1
2/1
2/1
2/1
2/1
2/1
KERNEL
0x00041FFF
Execution from Flash/EE
Instructions
LD
LDH
LDM/PUSH
STR
STRH
STRM/POP
0xFFFFFFFF
This operation is reversible: the Flash/EE can be remapped at
Address 0x00000000 by clearing Bit 0 of the remap MMR.
Precaution must again be taken to execute the remap function
from outside the mirrored area. Any kind of reset remaps the
Flash/EE memory at the bottom of the array.
Rev. 0 | Page 39 of 96
ADuC7121
Reset Operation
There are four types of reset: external reset, power-on reset,
watchdog expiration, and software force. The RSTSTA register
indicates the source of the last reset and RSTCLR clears the
RSTSTA register. These registers can be used during a reset
exception service routine to identify the source of the reset.
If RSTSTA is null, the reset was external. Note that when
clearing RSTSTA, all bits that are currently set to 1 must be
cleared. Otherwise, a reset event occurs.
Table 47. Remap MMR Bit Designations (Address = 0xFFFF0220, Default Value = 0x00)
Bit
0
Name
Remap
Description
Remap bit.
Set by the user to remap the SRAM to Address 0x00000000.
Cleared automatically after reset to remap the Flash/EE memory to Address 0x00000000.
Table 48. RSTSTA MMR Bit Designations (Address = 0xFFFF0230, Default Value = 0x0X)
Bit
7:3
2
1
0
Description
Reserved.
Software reset.
Set by the user to force a software reset.
Cleared by setting the corresponding bit in RSTCLR.
Watchdog timeout.
Set automatically when a watchdog timeout occurs.
Cleared by setting the corresponding bit in RSTCLR.
Power-on reset.
Set automatically when a power-on reset occurs.
Cleared by setting the corresponding bit in RSTCLR.
Rev. 0 | Page 40 of 96
ADuC7121
OTHER ANALOG PERIPHERALS
(see Figure 27). The signal range is 0 V to AVDD. Note that the
DAC can also operate in interpolation mode.
DIGITAL-TO-ANALOG CONVERTERS
The ADuC7121 incorporates four buffered 12-bit voltage output
string digital-to-analog converters (DACs) on chip. Each DAC has
a rail-to-rail voltage output buffer capable of driving 5 kΩ/100 pF.
MMR Interfaces
Each DAC is independently configurable through a control
register and a data register. These two registers are identical for
the 12 DACs. Only DAC0CON and DAC0DAT are described in
detail in this section.
Each DAC has three selectable ranges: 0 V to VREF (internal
band gap 2.5 V reference), 0 V to AVDD, and 0 V to EXT_REF
AVDD
AVDD
EXT_REF
EXT_REF
+
INT_REF
DAC_REBUF
+
DAC_REBUF
SW_A0
–
SW_A12
–
SW_B11
SW_B0
STRING
DAC
STRING
DAC
......
SW_C11
SW_C0
SW_D0
SW_D11
DAC0
DAC_BUF
......
Figure 27. DAC Configuration
SW_B
SW_C
12
UCLK
DIV
16/32
INTERPOLATOR
STRING
DAC
DAC_BUF
DACOUT
12
16
HCLK
DATA_REG
TIMER1
Figure 28. DAC User Functionality
Rev. 0 | Page 41 of 96
DAC12
09492-027
DAC_BUF
09492-028
INT_REF
ADuC7121
Table 49 DACxCON Registers (Default Value = 0x100, Read/Write Access)
Name
DAC0CON
DAC1CON
DAC2CON
DAC3CON
Address
0xFFFF0580
0xFFFF0588
0xFFFF05B0
0xFFFF05D8
Table 50. DAC0CON MMR Bit Designations
Bit
15:9
8
7
6
Value
0
1
0
0
DACPD
DACBUF_LP
BYP
5
0
DACCLK
4
0
DACCLR
3
0
Mode
2
1:0
0
Rate
DACRNx
00
01
10
11
Name
Description
Reserved.
DAC power-down. Set by the user to set DACOUTx to tristate mode.
DAC buffer low power mode. Set by the user to place DAC_BUFF into a low power mode.
DAC bypass bit.
Set this bit to bypass the DAC buffer.
Cleared to buffer the DAC output.
DAC update rate.
Set by the user to update the DAC using Timer1.
Cleared by the user to update the DAC using HCLK (core clock).
DAC clear bit.
Set by the user to enable normal DAC operation.
Cleared by the user to reset data register of the DAC to 0.
Mode bit.
Set by the user to operate on DAC normal mode and turn off the interpolator clock source. Cleared by the
user to enable the interpolation mode.
Rate bit. Set by the user to enable the interpolation clock to HCLK/16. Cleared by the user to HCLK/32.
DAC range bits.
DAC range is from AGND to the internal reference.
EXT_REF DAC range is from AGND to the external reference. See the REFCON MMR in Table 39 for details.
EXT_REF DAC range is from AGND to the external reference. See the REFCON MMR in Table 39 for more
details.
AVDD and AGND.
Table 51. DACxDAT Registers (Default Value = 0x00000000, Read/Write Access)
Name
DAC0DAT
DAC1DAT
DAC2DAT
DAC3DAT
Address
0xFFFF0584
0xFFFF058C
0xFFFF05B4
0xFFFF05DC
Table 52. DACxDAT MMR Bit Designations
Bit
31:28
27:16
15:12
11:0
Description
Reserved.
12-bit data for DACx.
Extra bits for interpolation mode.
Reserved.
Rev. 0 | Page 42 of 96
ADuC7121
Using the DACs
AVDD
AVDD – 100mV
The on-chip DAC architecture consists of a resistor string DAC
followed by an output buffer amplifier. The functional equivalent
is shown in Figure 29.
AVDD
VREF
EXT_REF
R
100mV
DAC0
R
0x00000000
0x0FFF0000
09492-030
R
Figure 30. Endpoint Nonlinearities Due to Amplifier Saturation
R
09492-029
R
Figure 29. DAC Structure
As shown in Figure 29, the reference source for each DAC is userselectable in software. It can be either AVDD, VREF, or EXT_REF. In
0 V-to-AVDD mode, the DAC output transfer function spans from
0 V to the voltage at the AVDD pin. In 0 V-to-EXT_REF mode,
the DAC output transfer function spans from 0 V to the voltage at
the VREF_2.5 pin. In 0 V-to-VREF mode, the DAC output transfer
function spans from 0 V to the internal 2.5 V reference, VREF.
The DAC output buffer amplifier features a true rail-to-rail
output stage implementation. This means that, when unloaded,
each output is capable of swinging to within less than 5 mV of
both AVDD and ground. Moreover, the linearity specification of the
DAC (when driving a 5 kΩ resistive load to ground) is guaranteed
through the full transfer function except for Code 0 to Code 100,
and, in 0 V-to-AVDD mode only, Code 3995 to Code 4095.
Linearity degradation near ground and AVDD is caused by saturation of the output amplifier, and a general representation of its
effects (neglecting offset and gain error) is shown in Figure 30. The
dotted line in Figure 30 indicates the ideal transfer function, and
the solid line represents what the transfer function may look
like with endpoint nonlinearities due to saturation of the output
amplifier. Note that Figure 30 represents a transfer function in 0 Vto-AVDD mode only. In 0 V-to-VREF or 0 V-to-EXT_REF modes
(with VREF < AVDD or EXT_REF < AVDD), the lower nonlinearity
is similar. However, the upper portion of the transfer function
follows the ideal line right to the end (VREF in this case, not AVDD),
showing no signs of endpoint linearity errors.
The endpoint nonlinearities conceptually illustrated in Figure 30
worsen as a function of output loading. The ADuC7121 data sheet
specifications assume a 5 kΩ resistive load to ground at the DAC
output. As the output is forced to source or sink more current,
the nonlinear regions at the top or bottom (respectively) of
Figure 30 become larger. With larger current demands, this can
significantly limit output voltage swing.
LDO (LOW DROPOUT REGULATOR)
The ADuC7121 contains an integrated LDO, which generates
the core supply voltage (DVDD) of approximately 2.6 V from
the IOVDD supply. As the LDO is driven from IOVDD, the
IOVDD supply voltage needs to be greater than 2.7 V.
An external compensation capacitor (CT) of 0.47 μF with low
ESR must be placed very close to each of the DVDD pins. This
capacitor also acts as a storage tank of charge, and supplies an
instantaneous charge required by the core, particularly at the
positive edge of the core clock (HCLK).
The DVDD voltage generated by the LDO is solely for providing
a supply for the ADuC7121. Therefore, users should not use a
DVDD pin as the power supply pin for any other chip. In
addition, it is recommended that the IOVDD has excellent
power supply decoupling to help improve line regulation
performance of the LDO.
The DVDD pin has no reverse battery, current limit, or thermal
shutdown protection; therefore, it is essential that users of the
ADuC7121 do not short this pin to ground at any time during
normal operation or during board manufacture.
CURRENT OUTPUT DACs (IDAC)
The ADuC7121 provides five current output digital-to-analog
converters (DACs). The current sources (five current DACs)
feature low noise and low drift high-side current output with
11-bit resolution. The five IDACs are as follows: IDAC0 with
250 mA full-scale (FS) output, IDAC1 with 200 mA FS output,
IDAC2 with 80 mA FS output, IDAC3 with 45 mA FS output,
and IDAC4 with 20 mA FS output.
Rev. 0 | Page 43 of 96
ADuC7121
The reference current of each IDAC is generated by a precision
internal band gap voltage reference and an external precision
resistor, and as such, the gain error of each IDAC is impacted by
the accuracy of the external resistor. Connect the resistor to the
IREF pin. The noise of each IDAC is limited by its damping
capacitor, CDAMP, which is selected to band limit noise as well
as to meet the signal bandwidth. Connect CDAMP_IDACx to PGND.
An NMOS switch is provided to shut down the IDAC0 diode.
Note that the output current switches off while this switch is on.
When the switch is on, the IDAC0 pin is able to withstand −0.5 V.
At power-up or reset, IDAC0 is powered down by default and
its output is high impedance. When enabled, the IDAC0 output
current does not overshoot.
To reduce the heat dissipation on chip, a separate power supply
can be used. An internal LDO provides a stable 2.5 V supply for
all low current internal IDACs.
Precision Current Generation and Fault Protection
The reference current is generated either from an on-chip
precision band gap voltage source or from an external voltage
reference by default, which is applied to an external precision
resistor. This resistor is connected to the IREF pin. The band gap
is factory trimmed to obtain a precise initial value and low
temperature drift. The external resistor is an assumed 0.1%
accuracy with 5 ppm drift, and a 0.1 μF external capacitor is
required to bypass high frequency noise.
A fault detection block is included to stop problems from occurring
if too small a reference resistor is detected. By sending the developed reference current into an on-board resistor of half the
expected size of the external resistor, a fault signal is generated
if the resistor is less than half the expected value (to an accuracy
of about 20%). The external resistor value is calculated by REXT =
VREF/IREF, where IREF = 370.37 μA and VREF is the selected
reference voltage for the voltage-to-current circuit.
IDAC and Output Stage Fault Protection
All five IDACs use the same architecture to generate high-side
current whereby only the section that generates the reference
current is shared. A low current is generated first using a currentmode DAC, which is then mirrored up to give the large output
current that is desired. A thermal shutdown circuit protects the
chip from overheating. The IDACs are guaranteed monotonic
to within 11 bits of resolution.
The bandwidth limit is provided by a programmable internal
resistor and an external capacitor. This is to filter high frequency
noise. It is also used to generate a triangle wave from a square
wave input for the IDAC4 only.
The thermal shutdown circuit automatically shuts down all of
the output stages when the chip temperature exceeds a certain
threshold. The intention of the thermal shutdown is only for
protection in the case of a short on an IDAC output. The overheating of the chip from other causes also triggers a thermal
shutdown but only the IDAC output stage is automatically shut
down. It triggers an interrupt and sets the TSHUT bit in the
IDACSTA register to indicate the overheating of the chip.
In case the digital core malfunctions at a temperature lower
than the thermal shutdown trigger point, the circuit can still
shut down the IDAC, but a watchdog reset must be used to reset
the chip. The TSHUT bit retains its value after a software reset
or a watchdog reset. This bit can only be cleared by a power-on
reset, a hardware reset, or when 0 is written to the IDACSTA
register.
Rev. 0 | Page 44 of 96
ADuC7121
0.47µF
PVDD
CDAMP
3.3V
VOLTAGE
REFERENCE
2.5V
IDAC
LDO
BUF
BUF
IOUT
IREF
REXT
PGND
09492-031
PULL_DOWN
Figure 31.
IDAC MMRs
Table 53. IDAC Control Registers (Read and Write Access)
Name
IDAC0CON
IDAC1CON
IDAC2CON
IDAC3CON
IDAC4CON
TDSCON
IDAC0PULLDOWN
Address (Hex)
0xFFFF0700
0xFFFF070C
0xFFFF0718
0xFFFF0724
0xFFFF0730
0xFFFF073C
0xFFFF0744
Default Value
0x0010
0x0010
0x0010
0x0010
0x0010
0x00
0x00
Table 54. IDACxCON MMR Bit Designations
Bit
15:9
8:7
Name
Value
SFHMODE
00
01
6
5
MSBSHFEN
LSBSHFEN
10
11
0
0
Description
These bits are reserved.
Bit shuffling is a method of
increasing the ac precision of an
IDAC. Do not use in applications
where dc performance is
important.
Shuffle one increment at a time.
Shuffle based on an internal
counter.
Shuffle based on the input data.
Reserved.
MSB shuffle enable.
Set by the user to 1 to enable MSB
shuffling.
Set by the user to 0 to disable MSB
shuffling.
LSB shuffle enable.
Set by the user to 1 to enable LSB
shuffling.
Set by the user to 0 to disable LSB
shuffling.
Bit
4
Name
IDACPD
Value
1
3
IDACCLK
0
2
IDACCLR
0
1
Mode
0
0
Reserved
0
Description
IDAC power-down bit.
Set by the user to 1 to power
down the IDAC. IDAC output is
high impedance.
Set by the user to 0 to power up
the IDAC.
IDAC update rate.
Set by the user to update the IDAC
using Timer1.
Cleared by the user to update the
IDAC using HCLK (core clock).
IDAC clear bit.
Set by the user to enable normal
IDAC operation.
Cleared by the user to reset data
register of the IDAC to 0.
Mode bit. This bit must always be
cleared.
Set this bit to 0.
Table 55. TDSCON MMR Bit Designations
Bit
7:3
2
Value
0
Name
Reserved
DISLR
1
0
DISINT
0
0
DISSD
Rev. 0 | Page 45 of 96
Description
The user sets these bits to 0.
Disable low external resistance bit.
Set by the user to 0 to disable the
output current DACs if the external
resistance is lower than a trip point.
Disable thermal trigger interrupt.
Set by the user to 0 to generate an
interrupt if the temperature passes
the thermal shutdown point.
Set by the user to 0 to disable the
output current DACs when the
temperature passes a trip point.
ADuC7121
Table 56. IDAC0PULLDOWN MMR Bit Designations
Table 60. IDACxBW MMR Bit Designations
Bit
7:6
5
Bit
7:4
3:0
4
Value
0
0
Name
Reserved
Pulldown
PLA_PD_EN
3:0
PLA Source
Description
These bits are set to 0 by the user.
IDAC0 pull-down.
Set to 1 by the user to pull down
the IDAC0 pin as well as power
down the IDAC0.
Set to 0 by the user to disable the
pull-down.
PLA output trigger enable.
Set to 1 by the user to enable the
PLA output to trigger the IDAC0
pull-down.
Set to 0 by the user to disable this
feature.
PLA output source for PLA output
trigger enable.
Can select the output of any
element, 0 to 15, by programming
these bits with the corresponding
binary value.
Table 57. IDAC Data Registers (Default Value = 0x00000000,
Read and Write Access)
Name
IDAC0DAT
IDAC1DAT
IDAC2DAT
IDAC3DAT
IDAC4DAT
Address (Hex)
0xFFFF0704
0xFFFF0710
0xFFFF071C
0xFFFF0728
0xFFFF0734
Table 58. IDACxDAT MMR Bit Designations
Bit
31:28
27:16
15:0
Name
Reserved
Data
Reserved
Value
000
Description
These bits are reserved.
Data from IDACx.
These bits are reserved.
Table 59. IDAC Bandwidth Registers (Default Value = 0x00,
Read and Write Access)
Name
IDAC0BW
IDAC1BW
IDAC2BW
IDAC3BW
IDAC4BW
Address
0xFFFF0708
0xFFFF0714
0xFFFF0720
0xFFFF072C
0xFFFF0738
Name
Reserved
BW
Value
Description
The user sets these bits to 0.
Bandwidth control bits. Defines the
3 dB bandwidth of the RC low-pass
filter, assuming a 0.01 μF capacitor
on the CDAMP_IDACx pins of the
IDACx.
100 kHz.
28.7 kHz.
15 kHz.
7.8 kHz.
4 kHz.
2.2 kHz.
1.2 kHz.
Not defined.
000
001
010
011
100
101
110
Others
Table 61. IDAC Status Register (Default Value = 0x00, Read
and Write Access)
Name
IDACSTA
Address (Hex)
0xFFFF0740
Table 62. IDACSTA MMR Bit Designations
Bit
7:2
1
Value
0
Name
Reserved
TSHUT
0
0
EXTRESLOW
Description
These bits are set to 0 by the user.
Thermal shutdown error status bit.
Set to 1 by the core indicating a
thermal shutdown event.
Set to 0 by the core indicating the
IDACs are within operating
temperature.
External resistor short bit.
Set to 1 by the core indicating an
external resistor short.
Set to 0 by the core when
operating normally.
OSCILLATOR AND PLL—POWER CONTROL
The ADuC7121 integrates a 32.768 kHz oscillator, a clock divider,
and a PLL. The PLL locks onto a multiple (1275) of the internal
oscillator to provide a stable 41.78 MHz clock for the system.
The core can operate at this frequency, or at binary submultiples
of it, to allow for power saving. The default core clock is the PLL
clock divided by 8 (CD = 3) or 5.2 MHz. The core clock frequency
can be output on the XCLK pin as described in Figure 32. Note
that when the XCLK pin is used to output the core clock, the
output signal is not buffered and is not suitable for use as a
clock source to an external device without an external buffer.
A power-down mode is available on the ADuC7121.
Rev. 0 | Page 46 of 96
ADuC7121
The operating mode, clocking mode, and programmable clock
divider are controlled via two MMRs, PLLCON (see Table 65) and
POWCON (see Table 66). PLLCON controls the operating
mode of the clock system, and POWCON controls the core
clock frequency and the power-down mode.
Example Source Code
T2LD = 5;
TCON = 0x480;
while ((T2VAL == t2val_old) || (T2VAL > 3))
//ensures timer value loaded
WATCHDOG
TIMER
INT. 32kHz1
OSCILLATOR
XTALO
CRYSTAL
OSCILLATOR
IRQEN = 0x10;
//enable T2 interrupt
XTALI
PLLKEY1 = 0xAA;
TIMERS
PLLCON = 0x01;
AT POWER-UP
PLLKEY2 = 0x55;
OCLK 32.768kHz
41.78MHz
PLL
P1.4/XCLK
POWKEY1 = 0x01;
MDCLK
UCLK
I2C
CD
CORE
POWCON = 0x27;
// set core into nap mode
ANALOG
PERIPHERALS
POWKEY2 = 0xF4;
/2CD
External Clock Selection
132.768kHz ±3%
09492-032
HCLK
P1.4/ECLK
Figure 32. Clocking System
To switch to an external clock on P1.4 (of the
P1.4/PWM1/ECLK/XCLK/PLAI[8] pin), configure P1.4 in
Mode 2. The external clock can be up to 41.78 MHz.
Example Source Code
External Crystal Selection
To switch to an external crystal, use the following procedure:
T2LD = 5;
1.
TCON = 0x480;
2.
3.
4.
Enable the Timer2 interrupt and configure it for a timeout
period of >120 μs.
Follow the write sequence to the PLLCON register, setting
the MDCLK bits to 01 and clearing the OSEL bit.
Force the part into nap mode by writing the correct write
sequence to the POWCON register.
When the part is interrupted from nap mode by the Timer2
interrupt source, the clock source has switched to the
external clock.
In noisy environments, noise can couple to the external crystal
pins, and PLL may lose lock momentarily. A PLL interrupt is
provided in the interrupt controller. The core clock is immediately
halted, and this interrupt is serviced only when the lock is restored.
In case of crystal loss, the watchdog timer should be used. During
initialization, a test on the RSTSTA register can determine if the
reset came from the watchdog timer.
while ((T2VAL == t2val_old) || (T2VAL > 3))
//ensures timer value loaded
IRQEN = 0x10;
//enable T2 interrupt
PLLKEY1 = 0xAA;
PLLCON = 0x03; //Select external clock
PLLKEY2 = 0x55;
POWKEY1 = 0x01;
POWCON = 0x27; // Set Core into Nap mode
POWKEY2 = 0xF4;
Power Control System
A choice of operating modes is available on the ADuC7121.
Table 63 describes what part of the ADuC7121 is powered on in
the different modes and indicates the power-up time. Table 64
gives some typical values of the total current consumption (analog
+ digital supply currents) in the different modes, depending on
the clock divider bits. The ADC is turned off. Note that these
values also include current consumption of the regulator and other
parts on the test board on which these values were measured.
Rev. 0 | Page 47 of 96
ADuC7121
Table 63. Operating Modes
Mode
Active
Pause
Nap
Sleep
Stop
Core
On
Peripherals
On
On
PLL
On
On
On
XTAL/Timer2/Timer3
On
On
On
On
External IRQ
On
On
On
On
On
Start-Up/Power-On Time
66 ms at CD = 0
24 ns at CD = 0; 3.06 μs at CD = 7
24 ns at CD = 0; 3.06 μs at CD = 7
1.58 ms
1.7 ms
Table 64. Typical Current Consumption at 25°C
PC[2:0]
000
001
010
011
100
Mode
Active
Pause
Nap
Sleep
Stop
CD = 0
33.1
22.7
3.8
0.4
0.4
CD = 1
21.2
13.3
3.8
0.4
0.4
CD = 2
13.8
8.5
3.8
0.4
0.4
CD = 3
10
6.1
3.8
0.4
0.4
Rev. 0 | Page 48 of 96
CD = 4
8.1
4.9
3.8
0.4
0.4
CD = 5
7.2
4.3
3.8
0.4
0.4
CD = 6
6.7
4
3.8
0.4
0.4
CD = 7
6.45
3.85
3.8
0.4
0.4
ADuC7121
MMRs and Keys
POWKEYx Registers
To prevent accidental programming, a certain sequence must be
followed when writing in the PLLCON and POWCON registers
(see Table 67).
Name:
POWKEY1
Address:
0xFFFF0404
PLLKEYx Registers
Default value:
0x0000
Name:
PLLKEY1
Access:
Write only
Address:
0xFFFF0410
Default value:
0x0000
Name:
POWKEY2
Access:
Write only
Address:
0xFFFF040C
Default value:
0x0000
Access:
Write only
Name:
PLLKEY2
Address:
0xFFFF0418
Default value:
0x0000
Access:
Write only
POWCON Register
Name:
POWCON
Address:
0xFFFF0408
PLLCON Register
Default value:
0x0003
Name:
PLLCON
Access:
Read and write
Address:
0xFFFF0414
Default value:
0x21
Access:
Read and write
Table 66. POWCON MMR Bit Designations
Bit
7
6:4
Value
Name
OSEL
4:2
1:0
MDCLK
00
01
10
11
Description
Reserved.
32 kHz PLL input selection.
Set by the user to use the internal
32 kHz oscillator.
Set by default.
Cleared by the user to use the external
32 kHz crystal.
Reserved.
Clocking modes.
Reserved.
PLL. Default configuration.
Reserved.
External clock on the
P1.4/PWM1/ECLK/XCLK/PLAI[8] pin.
Name
PC
000
001
010
011
Table 65. PLLCON MMR Bit Designations
Bit
7:6
5
Value
100
Others
3
2:0
RSVD
CD
000
001
010
011
100
101
110
111
Description
Reserved.
Operating modes.
Active mode.
Pause mode.
Nap mode.
Sleep mode. IRQ0 to IRQ3 and Timer2
can wake up the ADuC7121.
Stop mode.
Reserved.
Reserved.
CPU clock divider bits.
41.779200 MHz.
20.889600 MHz.
10.444800 MHz.
5.222400 MHz.
2.611200 MHz.
1.305600 MHz.
654.800 kHz.
326.400 kHz.
Table 67. PLLCON and POWCON Write Sequence
PLLCON
PLLKEY1 = 0xAA
PLLCON = 0x01
PLLKEY2 = 0x55
Rev. 0 | Page 49 of 96
POWCON
POWKEY1 = 0x01
POWCON = user value
POWKEY2 = 0xF4
ADuC7121
DIGITAL PERIPHERALS
PWM GENERAL OVERVIEW
The ADuC7121 integrates a 6-channel PWM interface. The PWM
outputs can be configured to drive an H-bridge or can be used as
standard PWM outputs. On power-up, the PWM outputs default
to H-bridge mode. This ensures that the motor is turned off by
default. In standard PWM mode, the outputs are arranged as three
pairs of PWM pins. Users have control over the period of each
pair of outputs and over the duty cycle of each individual output.
In all modes, the PWMxCOMx MMRs control the point at
which the PWM outputs change state. An example of the first pair
of PWM outputs (PWM1 and PWM2) is shown in Figure 33.
The PWM clock is selectable via PWMCON1 with one of the
following values: UCLK divide-by-2, 4, 8, 16, 32, 64, 128, or
256. The length of a PWM period is defined by PWMxLEN.
The PWM waveforms are set by the count value of the 16-bit
timer and the compare registers contents as shown with the
PWM1 and PWM2 waveforms above.
The low-side waveform, PWM2, goes high when the timer
count reaches PWM1LEN, and it goes low when the timer
count reaches the value held in PWM1COM3 or when the
high-side waveform PWM1 goes low.
The high-side waveform, PWM1, goes high when the timer
count reaches the value held in PWM1COM1, and it goes low
when the timer count reaches the value held in PWM1COM2.
HIGH SIDE
(PWM1)
LOW SIDE
(PWM2)
PWM1COM3
PWM1COM2
09492-033
PWM1COM1
PWM1LEN
Figure 33. PWM Timing
Table 68. PWM MMRs
Name
PWMCON1
PWM1COM1
PWM1COM2
PWM1COM3
PWM1LEN
PWM2COM1
PWM2COM2
PWM2COM3
PWM2LEN
PWM3COM1
PWM3COM2
PWM3COM3
PWM3LEN
PWMCON2
PWMICLR
Function
PWM control
Compare Register 1 for PWM Output 1 and PWM Output 2
Compare Register 2 for PWM Output 1 and PWM Output 2
Compare Register 3 for PWM Output 1 and PWM Output 2
Frequency control for PWM Output 1 and PWM Output 2
Compare Register 1 for PWM Output 3 and PWM Output 4
Compare Register 2 for PWM Output 3 and PWM Output 4
Compare Register 3 for PWM Output 3 and PWM Output 4
Frequency control for PWM Output 3 and PWM Output 4
Compare Register 1 for PWM Output 5 and PWM Output 6
Compare Register 2 for PWM Output 5 and PWM Output 6
Compare Register 3 for PWM Output 5 and PWM Output 6
Frequency control for PWM Output 5 and PWM Output 6
PWM convert start control
PWM interrupt clear
Rev. 0 | Page 50 of 96
ADuC7121
Table 69. PWMCON1 MMR Bit Designations (Address = 0xFFFF0F80, Default Value = 0x0012)
Bit
15
14
Name
Reserved
SYNC
13
PWM6INV
12
PWM4NV
11
PWM2INV
10
PWMTRIP
9
ENA
8:6
PWMCP[2:0]
5
POINV
4
HOFF
3
LCOMP
2
DIR
1
HMODE
0
PWMEN
Description
This bit is reserved.
Enables PWM synchronization.
Set to 1 by the user so that all PWM counters are reset on the next clock edge after the detection of a high-to-low
transition on SYNC of the P0.3/MISO/PLAO[12]/SYNC pin.
Cleared by the user to ignore transitions on SYNC of the P0.3/MISO/PLAO[12]/SYNC pin.
Set to 1 by the user to invert PWM6.
Cleared by the user to use PWM6 in normal mode.
Set to 1 by the user to invert PWM4.
Cleared by the user to use PWM4 in normal mode.
Set to 1 by the user to invert PWM2.
Cleared by the user to use PWM2 in normal mode.
Set to 1 by the user to enable PWM trip interrupt. When the PWMTRIP input is low, the PWMEN bit is cleared and an
interrupt is generated.
Cleared by the user to disable the PWMTRIP interrupt.
If HOFF = 0 and HMODE = 1. If HOFF = 1 and HMODE = 1, see Table 70. If not in H-Bridge mode, this bit has no effect.
Set to 1 by the user to enable PWM outputs.
Cleared by the user to disable PWM outputs.
PWM clock prescaler bits. Sets the UCLK divider.
000 = UCLK divide-by-2.
001 = UCLK divide-by-4.
010 = UCLK divide-by-8.
011 = UCLK divide-by-16.
100 = UCLK divide-by-32.
101 = UCLK divide-by-64.
110 = UCLK divide-by-128.
111 = UCLK divide-by-256.
Set to 1 by the user to invert all PWM outputs.
Cleared by the user to use PWM outputs as normal.
High-side off.
Set to 1 by the user to force PWM1 and PWM3 outputs high. This also forces PWM2 and PWM4 low.
Cleared by the user to use the PWM outputs as normal.
Load compare registers.
Set to 1 by the user to load the internal compare registers with the values in PWMxCOMx on the next transition of the
PWM timer from 0x00 to 0x01.
Cleared by the user to use the values previously stored in the internal compare registers.
Direction control.
Set to 1 by the user to enable PWM1 and PWM2 as the output signals while PWM3 and PWM4 are held low.
Cleared by the user to enable PWM3 and PWM4 as the output signals while PWM1 and PWM2 are held low.
Enables H-bridge mode.
Set to 1 by the user to enable H-Bridge mode and Bits[5:2] of PWMCON1.
Cleared by the user to operate the PWMs in standard mode.
Set to 1 by the user to enable all PWM outputs.
Cleared by the user to disable all PWM outputs.
Rev. 0 | Page 51 of 96
ADuC7121
In H-bridge mode, HMODE = 1 and Table 69 determine the
PWM outputs, as listed in Table 70.
Table 72. PWMCON2 MMR Bit Designations (Address =
0xFFFF0FB4, Default Value = 0x00)
Table 70. PWM Output Selection
Bit
7
Name
CSEN
3:0
CSD3 to
CSD0
1
PWMCOM1 MMR
HOFF POINV
0
X1
1
X1
0
0
0
0
0
1
0
1
DIR
X1
X1
0
1
0
1
PWM1
1
1
0
HS1
HS1
1
PWM Outputs
PWM2 PWMR3
1
1
0
1
0
HS1
1
LS
0
LS1
1
1
HS1
PWM4
1
0
LS1
0
1
LS1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
HS is high side, LS is low side, X is a don’t care bit.
On power-up, PWMCON1 defaults to 0x12 (HOFF = 1 and
HMODE = 1). All GPIO pins associated with the PWM are
configured in PWM mode by default (see Table 71).
Table 71. Compare Register (Default Value = 0x0000, Access
is Read/Write)
Name
PWM1COM1
PWM1COM2
PWM1COM3
PWM2COM1
PWM2COM2
PWM2COM3
PWM3COM1
PWM3COM2
PWM3COM3
Address
0xFFFF0F84
0xFFFF0F88
0xFFFF0F8C
0xFFFF0F94
0xFFFF0F98
0xFFFF0F9C
0xFFFF0FA4
0xFFFF0FA8
0xFFFF0FAC
Default Value
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The PWM trip interrupt can be cleared by writing any value to
the PWMICLR MMR. Note that when using the PWM trip interrupt, users should make sure that the PWM interrupt has been
cleared before exiting the ISR. This prevents generation of multiple
interrupts.
When calculating the time from the convert start delay to the
start of an ADC conversion, the user needs to take account of
internal delays. The following example shows the case for a
delay of four clocks. One additional clock is required to pass the
convert start signal to the ADC logic. When the ADC logic
receives the convert start signal, an ADC conversion begins on
the next ADC clock edge (see Figure 34).
UCLOCK
PWM CONVERT START CONTROL
The PWM can be configured to generate an ADC convert start
signal after the active low side signal goes high. There is a programmable delay between when the low-side signal goes high and the
convert start signal is generated.
This is controlled via the PWMCON2 MMR. If the delay
selected is higher than the width of the PWM pulse, the
interrupt remains low.
Description
Set to 1 by the user to enable the PWM to
generate a convert start signal.
Cleared by the user to disable the PWM
convert start signal.
Convert start delay. Delays the convert start
signal by a number of clock pulses.
4 clock pulses.
8 clock pulses.
12 clock pulses.
16 clock pulses.
20 clock pulses.
24 clock pulses.
28 clock pulses.
32 clock pulses.
36 clock pulses.
40 clock pulses.
44 clock pulses.
48 clock pulses.
52 clock pulses.
56 clock pulses.
60 clock pulses.
64 clock pulses.
LOW SIDE
COUNT
PWM SIGNAL
TO CONVST
09492-034
ENA
0
X1
1
1
1
1
Value
SIGNAL PASSED
TO ADC LOGIC
Figure 34. ADC Conversion
Rev. 0 | Page 52 of 96
ADuC7121
GENERAL-PURPOSE INPUT/OUTPUT
The ADuC7121 provides 32 general-purpose, bidirectional
input/output (GPIO) pins. All I/O pins are 5 V tolerant,
meaning that the GPIOs support an input voltage of 5 V. In
general, many of the GPIO pins have multiple functions (see
Table 73). By default, the GPIO pins are configured in GPIO mode.
Name:
GP2CON
Address:
0xFFFF0D08
Default value:
0x00000000
All GPIO pins have an internal pull-up resistor (of about 100 kΩ)
and their drive capability is 1.6 mA. Note that a maximum of
20 GPIOs can drive 1.6 mA at the same time. The 32 GPIOs are
grouped into four ports: Port 0 to Port 3. Each port is controlled
by four or five MMRs, with x representing the port number.
Access:
Read and write
Name:
GP3CON
Address:
0xFFFF0D0C
Default value:
0x00000000
Access:
Read and write
GPxCON Registers
Name:
GP0CON
Address:
0xFFFF0D00
Default value:
0x11000000
Access:
Read and write
The input level of any GPIO can be read at any time in the
GPxDAT MMR, even when the pin is configured in a mode
other than GPIO. The PLA input is always active.
Name:
GP1CON
When the ADuC7121 device enters a power-saving mode, the
GPIO pins retain their state.
Address:
0xFFFF0D04
GPxCON is the Port x control register, and it selects the
function of each pin of Port x, as described in Table 73.
Default value:
0x00000000
Access:
Read and write
Rev. 0 | Page 53 of 96
ADuC7121
Table 73. GPIO Pin Function Designations
Port
0
1
2
3
1
Pin
P0.0
P0.1
P0.2
P0.3
P0.4
P0.5
00
GPIO
GPIO
GPIO
GPIO
GPIO
GPIO
Configuration (See GPxCON Table 74)
01
10
SCL0
SDA0
JTAG disabled
SPICLK
JTAG disabled ADCBUSY
MISO
SYNC (PWM)
MOSI
TRIP (PWM)
ADCCONVST
CS
11
PLAI[5]
PLAI[4]
PLAO[13]
PLAO[12]
PLAI[11]
PLAI[10]
P0.6
P0.7
GPIO
GPIO
MRST
TRST
PLAI[2]
PLAI[3]
P1.0
P1.1
P1.2 1
P1.31
P1.4
P1.5
P1.6
P1.7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
GPIO
GPIO
TDI (JTAG)
TDO (JTAG)
GPIO
GPIO
GPIO
GPIO
GPIO/IRQ0
GPIO/IRQ1
GPIO
GPIO/IRQ2
GPIO
GPIO
GPIO/IRQ3
GPIO
GPIO
GPIO
GPIO/IRQ4
GPIO/IRQ5
GPIO
GPIO
GPIO
GPIO/BM
SIN
SOUT
SCL1
SDA1
PWM1
PWM2
ECLK/XCLK
PWM5
PWM6
PWM3
PWM4
Reconfiguring these pins disables JTAG mode. Erase part to reenable JTAG access after changing default value.
Rev. 0 | Page 54 of 96
PLAI[7]
PLAI[6]
PLAO[15]
PLAO[14]
PLAI[8]
PLAI[9]
PLAO[5]
PLAO[4]
PLAI[13]
PLAI[12]
PLAI[1]
PLAI[14]
PLAO[7]
PLAO[6]
PLAI[15]
PLAI[0]
PLAO[0]
PLAO[1]
PLAO[2]
PLAO[3]
PLAO[8]
PLAO[9]
PLAO[10]
PLAO[11]
ADuC7121
Table 74. GPxCON MMR Bit Designations
Table 75. GPxPAR MMR Bit Designations
Bit
31:30
29:28
27:26
25:24
23:22
21:20
19:18
17:16
15:14
13:12
11:10
9:8
7:6
5:4
3:2
1:0
Bit
31:29
28
Description
Reserved
Select function of the Px.7 pin
Reserved
Select function of the Px.6 pin
Reserved
Select function of the Px.5 pin
Reserved
Select function of the Px.4 pin
Reserved
Select function of the Px.3 pin
Reserved
Select function of the Px.2 pin
Reserved
Select function of the Px.1 pin
Reserved
Select function of the Px.0 pin
27:25
24
23:21
20
19:17
16
15:13
12
11:9
8
7:5
4
3:1
0
GPxPAR Registers
The GPxPAR registers program the parameters for Port 0, Port 1,
Port 2, and Port 3. Note that the GPxDAT MMR must always be
written after changing the GPxPAR MMR.
Name:
GP0PAR
Address:
0xFFFF0D2C
Default value:
0x20000000
Access:
Read and write
Name:
GP1PAR
Address:
0xFFFF0D3C
Default value:
0x00000000
Access:
Read and write
Name:
GP2PAR
Address:
0xFFFF0D4C
Default value:
0x00000000
Access:
Read and write
Name:
GP3PAR
Address:
0xFFFF0D5C
Default value:
0x00222222
Access:
Read and write
Description
Reserved
Pull-up disable Px.7 pin
Set to 1 to enable the pull-up
Clear to 0 to disable the pull-up
Reserved
Pull-up disable Px.6 pin
Reserved
Pull-up disable Px.5 pin
Reserved
Pull-up disable Px.4 pin
Reserved
Pull-up disable Px.3 pin
Reserved
Pull-up disable Px.2 pin
Reserved
Pull-up disable Px.1 pin
Reserved
Pull-up disable Px.0 pin
GPxDAT Register
GPxDAT is a Port x configuration and data register. It configures
the direction of the GPIO pins of Port x, sets the output value
for the pins configured as output, and receives and stores the
input value of the pins configured as inputs.
Name:
GP0DAT
Address:
0xFFFF0D20
Default value:
0x000000XX
Access:
Read and write
Name:
GP1DAT
Address:
0xFFFF0D30
Default value:
0x000000XX
Access:
Read and write
Name:
GP2DAT
Address:
0xFFFF0D40
Default value:
0x000000XX
Access:
Read and write
Rev. 0 | Page 55 of 96
ADuC7121
Name:
GP3DAT
Table 77. GPxSET MMR Bit Designations
Address:
0xFFFF0D50
Default value:
0x000000XX
Bit
31: 24
23:16
Access:
Read and write
Description
Reserved.
Data Port x set bit.
Set to 1 by the user to set the bit on Port x; also sets
the corresponding bit in the GPxDAT MMR.
Cleared to 0 by user; does not affect the data out.
Reserved.
Table 76. GPxDAT MMR Bit Designations
15:0
Bit
31:24
GPxCLR Registers
Description
Direction of the data.
Set to 1 by the user to configure the GPIO pin as an
output.
Cleared to 0 by the user to configure the GPIO pin as
an input.
Port x data output.
Reflect the state of Port x pins at reset (read only).
Port x data input (read only).
The GPxCLR registers are data clear for Port x registers.
Name:
GP0CLR
Address:
0xFFFF0D28
Default value:
0x000000XX
Access:
Write only
The GPxSET registers provide a data set for the Port x registers.
Name:
GP1CLR
Name:
GP0SET
Address:
0xFFFF0D38
Address:
0xFFFF0D24
Default value:
0x000000XX
Default value:
0x000000XX
Access:
Write only
Access:
Write only
Name:
GP2CLR
23:16
15:8
7:0
GPxSET Registers
Name:
GP1SET
Address:
0xFFFF0D48
Address:
0xFFFF0D34
Default value:
0x000000XX
Default value:
0x000000XX
Access:
Write only
Access:
Write only
Name:
GP3CLR
Name:
GP2SET
Address:
0xFFFF0D58
Address:
0xFFFF0D44
Default value:
0x000000XX
Default value:
0x000000XX
Access:
Write only
Access:
Write only
Table 78. GPxCLR MMR Bit Designations
Name:
GP3SET
Bit
31:24
23:16
Address:
0xFFFF0D54
Default value:
0x000000XX
Access:
Write only
15:0
Description
Reserved.
Data Port x clear bit.
Set to 1 by the user to clear bit on Port x; also clears
the corresponding bit in the GPxDAT MMR.
Cleared to 0 by user; does not affect the data output.
Reserved.
GPxOCE Registers
Open-collector functionality is available on the following GPIO
pins: P1.7, P1.6, Port 2, and Port 3.
Rev. 0 | Page 56 of 96
ADuC7121
Table 79. GPxOCE MMR Bit Designations
Bit
31:8
7
6
5
4
3
2
1
0
Description
Reserved.
GPIO Px.7 open collector enable.
Set to 1 by the user to enable the open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.6 open collector enable.
Set to 1 by the user to enable the open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.5 open collector enable.
Set to 1 by the user to enable open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.4 open collector enable.
Set to 1 by the user to enable open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.3 open collector enable.
Set to 1 by the user to enable open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.2 open collector enable.
Set to 1 by the user to enable open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.1 open collector enable.
Set to 1 by the user to enable open collector.
Set to 0 by the user to disable the open collector.
GPIO Px.0 open collector enable.
Set to 1 by the user to enable open collector.
Set to 0 by the user to disable the open collector.
Rev. 0 | Page 57 of 96
ADuC7121
UART SERIAL INTERFACE
The ADuC7121 features a 16,450-compatible UART. The UART
is a full-duplex, universal, asynchronous receiver/transmitter. A
UART performs serial-to-parallel conversion on data characters
received from a peripheral device, and parallel-to-serial conversion on data characters received from the ARM7TDMI. The
UART features a fractional divider that facilitates high accuracy
baud rate generation. The UART functionality is available on
the P1.0/SIN/SCL1/PLAI[7] and P1.1/SOUT/SDA1/PLAI[6]
pins of the ADuC7121.
Calculation of the baud rate using fractional divider is as
follows:
Baud Rate =
M+
41.78 MHz
16 × DL × 2 × ( M +
41.78 MHz
N
=
2048 Baud Rate × 16 × DL × 2
For example, generation of 19,200 baud
The serial communication adopts an asynchronous protocol
that supports various word length, stop bits, and parity generation options selectable in the configuration register.
M+
41.78 MHz
N
=
2048 19200 × 16 × 67 × 2
BAUD RATE GENERATION
M+
N
= 1.015
2048
The ADuC7121 features two methods of generating the UART
baud rate: normal 450 UART baud rate generation and ADuC7121
fractional divider.
where:
M=1
N = 0.015 × 2048 = 30
Normal 450 UART Baud Rate Generation
The baud rate is a divided version of the core clock using the
value in COMDIV0 and COMDIV1 MMRs (16-bit value, DL).
The standard baud rate generator formula is
Baud rate =
41.78 MHz
(1)
16 × 2 × DL
Table 80. Baud Rate Using the Standard Baud Rate Generator
DL
0x88
0x44
0x0B
Actual Baud Rate
9600
19,200
118,691
% Error
0%
0%
3%
Fractional Divider
The fractional divider combined with the normal baud rate
generator allows the generating of a wider range of more
accurate baud rates.
/2
FBEN
/16DL
UART
/(M + N/2048)
09492-035
CORE
CLOCK
Baud Rate =
41.78 MHz
(
16 × 67 × 2 × 1 +
30
2048
)
where Baud Rate = 19,219 bps.
UART REGISTER DEFINITION
The UART interface consists of the following ten registers:
Table 80 lists common baud rate values.
Baud Rate
9600
19,200
115,200
N
)
2048
•
•
•
•
•
•
•
•
•
•
COMTX: 8-bit transmit register
COMRX: 8-bit receive register
COMDIV0: divisor latch (low byte)
COMDIV1: divisor latch (high byte)
COMCON0: line control register
COMCON1: line control register
COMSTA0: line status register
COMIEN0: interrupt enable register
COMIID0: interrupt identification register
COMDIV2: 16-bit fractional baud divide register
COMTX, COMRX, and COMDIV0 share the same address
location. COMTX and COMRX can be accessed when Bit 7 in
the COMCON0 register is cleared. COMDIV0 can be accessed
when Bit 7 of COMCON0 is set.
Figure 35. Baud Rate Generation Options
Rev. 0 | Page 58 of 96
ADuC7121
UART TX Register
UART Divisor Latch Register 1
Write to this 8-bit register to transmit data using the UART.
Name:
COMTX
This 8-bit register contains the most significant byte of the
divisor latch that controls the baud rate at which the UART
operates.
Address:
0xFFFF0800
Name:
COMDIV1
Access:
Write only
Address:
0xFFFF0804
UART RX Register
Default value:
0x00
This 8-bit register is read from to receive data transmitted using
the UART.
Access:
Read and write
Name:
COMRX
UART Control Register 0
Address:
0xFFFF0800
This 8-bit register controls the operation of the UART in
conjunction with COMCON1.
Default value:
0x00
Name:
COMCON0
Access:
Read only
Address:
0xFFFF080C
UART Divisor Latch Register 0
Default value:
0x00
This 8-bit register contains the least significant byte of the
divisor latch that controls the baud rate at which the UART
operates.
Access:
Read and write
Name:
COMDIV0
Address:
0xFFFF0800
Default value:
0x00
Access:
Read and write
Rev. 0 | Page 59 of 96
ADuC7121
Table 81. COMCON0 MMR Bit Designations
Bit
7
Name
DLAB
6
BRK
5
SP
4
EPS
3
PEN
2
STOP
1 to 0
WLS
Description
Divisor latch access.
Set by the user to enable access to COMDIV0 and COMDIV1 registers.
Cleared by the user to disable access to COMDIV0 and COMDIV1 and enable access to COMRX,
COMTX, and COMIEN0.
Set break.
Set by the user to force the transmit pin (SOUT) to 0.
Cleared to operate in normal mode.
Stick parity. Set by the user to force parity to defined values.
1 if EPS = 1 and PEN = 1.
0 if EPS = 0 and PEN = 1.
Even parity select bit.
Set for even parity.
Cleared for odd parity.
Parity enable bit.
Set by the user to transmit and check the parity bit.
Cleared by the user for no parity transmission or checking.
Stop bit.
Set by the user to transmit 1.5 stop bits if the word length is five bits, or two stop bits if the word
length is six, seven, or eight bits. The receiver checks the first stop bit only, regardless of the
number of stop bits selected.
Cleared by the user to generate one stop bit in the transmitted data.
Word length select.
00 = five bits.
01 = six bits.
10 = seven bits.
11 = eight bits.
UART Control Register 1
Table 82. COMCON1 MMR Bit Designations
This 8-bit register controls the operation of the UART in
conjunction with COMCON0.
Bit
7:5
4
Name:
COMCON1
Address:
0xFFFF0810
Default value:
0x00
Access:
Read and write
Name
LOOPBACK
3:2
1
RTS
0
DTR
Rev. 0 | Page 60 of 96
Description
Reserved bits. Not used.
Loopback. Set by the user to enable
loopback mode. In loopback mode, SOUT is
forced high.
Reserved bits. Not used.
Request to send.
Set by the user to force the RTS output to 0.
Cleared by the user to force the RTS output
to 1.
Data terminal ready.
Set by the user to force the DTR output to 0.
Cleared by the user to force the DTR output
to 1.
ADuC7121
UART Status Register 0
Name:
COMSTA0
Address:
0xFFFF0814
Default value:
0x60
Access:
Read only
Function:
This 8-bit read-only register reflects the current status on the UART.
Table 83. COMSTA0 MMR Bit Designations
Bit
7
6
Name
5
THRE
4
BI
3
FE
2
PE
1
OE
0
DR
TEMT
Description
Reserved.
COMTX and shift register empty status bit.
Set automatically if COMTX and the shift register are empty. This bit indicates that the data has
been transmitted, that is, no more data is present in the shift register.
Cleared automatically when writing to COMTX.
COMTX empty status bit.
Set automatically if COMTX is empty. COMTX can be written as soon as this bit is set; the previous
data might not have been transmitted yet and can still be present in the shift register.
Cleared automatically when writing to COMTX.
Break indicator.
Set when SIN of the P1.0/SIN/SCL1/PLAI[7] pin is held low for more than the maximum word
length.
Cleared automatically.
Framing error.
Set when the stop bit is invalid.
Cleared automatically.
Parity error.
Set when a parity error occurs.
Cleared automatically.
Overrun error.
Set automatically if data are overwritten before being read.
Cleared automatically.
Data ready.
Set automatically when COMRX is full.
Cleared by reading COMRX.
Rev. 0 | Page 61 of 96
ADuC7121
UART Interrupt Enable Register 0
Table 85. COMIID0 MMR Bit Designations
This 8-bit register enables and disables the individual UART
interrupt sources.
Name:
COMIEN0
Address:
0xFFFF0804
Default value:
0x00
Access:
Read and write
Table 84. COMIEN0 MMR Bit Designations
Bit
7 to 3
Name
2
ELSI
1
0
ETBEI
ERBFI
Description
Reserved. Not used.
Cleared by the user.
Receive pin (SIN) status interrupt enable
bit.
Set by the user to enable generation of
an interrupt if any of the COMSTA0[3:1]
register bits are set.
Cleared by the user.
Enable transmit buffer empty interrupt.
Set by the user to enable an interrupt
when the buffer is empty during a
transmission, that is, when COMSTA[5]
is set.
Cleared by the user.
Enable receive buffer full interrupt.
Set by the user to enable an interrupt
when the buffer is full during a
reception.
Cleared by the user.
Bits[2:1]
Status
Bits
00
11
Bit 0
NINT
1
0
1
10
0
2
01
0
3
00
0
4
Address:
0xFFFF0808
Default value:
0x01
Access:
Read only
Clearing
Operation
Read
COMSTA0
Read COMRX
Write data to
COMTX or
read COMIID0
Read
COMSTA1
register
This 16-bit register controls the operation of the fractional
divider for the ADuC7121.
Name:
COMDIV2
Address:
0xFFFF082C
Default value:
0x0000
Access:
Read and write
Table 86. COMDIV2 MMR Bit Designations
Bit
15
Name
FBEN
14:13
12:11
FBM[1:0]
10:0
FBN[10:0]
This 8-bit register reflects the source of the UART interrupt.
COMIID0
Definition
No interrupt
Receive line
status
interrupt
Receive
buffer full
interrupt
Transmit
buffer empty
interrupt
Modem
status
interrupt
UART Fractional Divider Register
UART Interrupt Identification Register 0
Name:
Priority
Rev. 0 | Page 62 of 96
Description
Fractional baud rate generator enable bit.
Set by the user to enable the fractional
baud rate generator.
Cleared by the user to generate the baud
rate using the standard 450 UART baud rate
generator.
Reserved.
M. If FBM = 0, M = 4. See Equation 2 for the
calculation of the baud rate using a
fractional divider and Table 80 for common
baud rate values.
N. See Equation 2 for the calculation of the
baud rate using a fractional divider and
Table 80 for common baud rate values.
ADuC7121
I2C PERIPHERALS
The ADuC7121 incorporates two I2C peripherals that may be
configured as a fully I2C-compatible bus master device or as a
fully I2C-compatible bus slave device. Both peripherals are
identical.
The two pins used for data transfer, SDA and SCL, are configured
in a wired-AND format that allows arbitration in a multimaster
system. These pins require external pull-up resistors. Typical
pull-up values are between 4.7 kΩ and 10 kΩ.
The address of the I2C bus peripheral in the I2C bus system is
programmed by the user. This ID can be modified any time a
transfer is not in progress. The user can configure the interface
to respond to four slave addresses.
2
The transfer sequence of an I C system consists of a master device
initiating a transfer by generating a start condition while the bus
is idle. The master transmits the slave device address and the
direction of the data transfer (R/W) during the initial address
transfer. If the master does not lose arbitration and the slave
acknowledges, the data transfer is initiated. This continues until
the master issues a stop condition and the bus becomes idle.
The I2C peripheral can only be configured as a master or slave
at any given time. The same I2C channel cannot simultaneously
support master and slave modes. The I2C interface on the
ADuC7121 includes the following features:
•
•
•
•
•
•
•
•
Support for repeated start conditions. In master mode, the
ADuC7121 can be programmed to generate a repeated
start. In slave mode, the ADuC7121 recognizes repeated
start conditions.
In master and slave modes, the device recognizes both
7-bit and 10-bit bus addresses.
In I2C Master mode, the ADuC7121 supports continuous
reads from a single slave up to 512 bytes in a single transfer
sequence.
Clock stretching is supported in both master and slave
modes.
In slave mode, the ADuC7121 can be programmed to
return a no acknowledge. This allows the validation of
checksum bytes at the end of I2C transfers.
Bus arbitration in master mode is supported.
Internal and external loopback modes are supported for
I2C hardware testing in loopback mode.
The transmit and receive circuits in both master and slave
mode contain 2-byte FIFOs. Status bits are available to the
user to control these FIFOs.
Configuring External Pins for I2C Functionality
The I2C pins of the ADuC7121 device are P0.0 and P0.1 for
I2C0, and P1.0 and P1.1 for I2C1. P0.0 and P1.0 are the I2C clock
signals, and P0.1 and P1.1 are the I2C data signals. For instance,
to configure the I2C0 pins (SCL0, SDA0), Bit 0 and Bit 4 of the
GP0CON register must be set to 1 to enable I2C mode. To
configure the I2C1 pins (SCL1, SDA1), Bit 1 and Bit 5 of the
GP1CON register must be set to 1 to enable I2C mode, as shown
in the
General-Purpose Input/Output section.
SERIAL CLOCK GENERATION
The I2C master in the system generates the serial clock for a
transfer. The master channel can be configured to operate in
fast mode (400 kHz) or standard mode (100 kHz). The bit rate
is defined in the I2CDIV MMR as follows:
f SERIAL CLOCK =
fUCLK
(2 + DIVH ) + (2 + DIVL)
where:
fUCLK = clock before the clock divider.
DIVH = the high period of the clock.
DIVL = the low period of the clock.
Thus, for 100 kHz operation
DIVH = DIVL = 0xCF
and for 400 kHz
DIVH = 0x28, DIVL = 0x3C
The I2CDIV register corresponds to DIVH:DIVL.
I2C BUS ADDRESSES
Slave Mode
In slave mode, the registers I2CxID0, I2CxID1, I2CxID2, and
I2CxID3 contain the device IDs. The device compares the four
I2CxIDx registers to the address byte received from the bus
master. To be correctly addressed, the 7 MSBs of either ID
register must be identical to that of the 7 MSBs of the first
received address byte. The LSB of the ID registers (the transfer
direction bit) is ignored in the process of address recognition.
The ADuC7121 also supports 10-bit addressing mode. When
Bit 1 of I2CxSCON (ADR10EN bit) is set to 1, then one 10-bit
address is supported in slave mode and is stored in registers
I2CxID0 and I2CxID1. The 10-bit address is derived as follows:
I2CxID0[0] is the read/write bit and is not part of the I2C address.
•
•
•
I2CxID0[7:1] = Address Bits[6:0].
I2CxID1[2:0] = Address Bits[9:7].
I2CxID1[7:3] must be set to 11110b.
Master Mode
In master mode, the I2CxADR0 register is programmed with
the I2C address of the device.
In 7-bit address mode, I2CxADR0[7:1] are set to the device
address. I2CxADR0[0] is the read/write bit.
In 10-bit address mode, the 10-bit address is created as follows:
•
•
•
Rev. 0 | Page 63 of 96
I2CxADR0[7:3] must be set to 11110b.
I2CxADR0[2:1] = Address Bits[9:8].
I2CxADR1[7:0] = Address Bits[7:0].
ADuC7121
•
I2CxADR0[0] is the read/write bit.
I2C REGISTERS
The I2C peripheral interfaces consists of a number of MMRs. These are described in the following section.
I2C Master Registers
I2C Master Control Register
This 16-bit MMR configures I2C peripheral in master mode.
Name:
I2C0MCTL, I2C1MCTL
Address:
0xFFFF0880, 0xFFFF0900
Default value:
0x0000, 0x0000
Access:
Read/write
Table 87. I2CxMCTL MMR Bit Designations
Bit
15:9
8
Name
7
I2CNACKENI
6
I2CALENI
5
I2CMTENI
4
I2CMRENI
3
I2CMSEN
2
I2CILEN
1
I2CBD
0
I2CMEN
I2CMCENI
Description
Reserved. These bits are reserved; do not write to these bits.
I2C transmission complete interrupt enable bit.
Set this bit to enable an interrupt on detecting a stop condition on the I2C bus.
Clear this interrupt source.
I2C no acknowledge received interrupt enable bit.
Set this bit to enable interrupts when the I2C master receives a no acknowledge.
Clear this interrupt source.
I2C arbitration lost interrupt enable bit.
Set this bit to enable interrupts when the I2C master has been unsuccessful in gaining control of the I2C bus.
Clear this interrupt source.
I2C transmit interrupt enable bit.
Set this bit to enable interrupts when the I2C master has transmitted a byte.
Clear this interrupt source.
I2C receive interrupt enable bit.
Set this bit to enable interrupts when the I2C master receives data.
Cleared by the user to disable interrupts when the I2C master is receiving data.
I2C master SCL stretch enable bit.
Set this bit to 1 to enable clock stretching. When SCL is low, setting this bit forces the device to hold SCL low until
I2CMSEN is cleared. If SCL is high, setting this bit forces the device to hold SCL low after the next falling edge.
Clear this bit to disable clock stretching.
I2C internal loopback enable.
Set this bit to enable loopback test mode. In this mode, the SCL and SDA signals are connected internally to their
respective input signals.
Cleared by the user to disable loopback mode.
I2C master back off disable bit.
Set this bit to allow the device to compete for control of the bus even if another device is currently driving a start
condition.
Clear this bit to back off until the I2C bus becomes free.
I2C master enable bit.
Set by the user to enable I2C master mode.
Clear this bit to disable I2C master mode.
Rev. 0 | Page 64 of 96
ADuC7121
I2C Master Status Register
This 16-bit MMR is I2C status register in master mode.
Name:
I2C0MSTA, I2C1MSTA
Address:
0xFFFF0884, 0xFFFF0904
Default value:
0x0000, 0x0000
Access:
Read only
Table 88 I2CxMSTA MMR Bit Designations
Bit
15:11
10
Name
9
I2CMRxFO
8
I2CMTC
7
I2CMNA
6
I2CMBUSY
5
I2CAL
4
I2CMNA
3
I2CMRXQ
2
I2CMTXQ
1:0
I2CMTFSTA
I2CBBUSY
Description
Reserved. These bits are reserved.
I2C bus busy status bit.
This bit is set to 1 when a start condition is detected on the I2C bus.
This bit is cleared when a stop condition is detected on the bus.
Master receiver (Rx) FIFO overflow.
This bit is set to 1 when a byte is written to the Rx FIFO when it is already full.
This bit is cleared in all other conditions.
I2C transmission complete status bit.
This bit is set to 1 when a transmission is complete between the master and the slave with which it was
communicating. If the I2CMCENI bit in I2CxMCTL is set, an interrupt is generated when the I2CMTC bit is set.
Clear this interrupt source.
I2C master no acknowledge data bit.
This bit is set to 1 when a no acknowledge condition is received by the master in response to a data write transfer. If
the I2CNACKENI bit in I2CxMCTL is set, an interrupt is generated when the I2CMNA bit is set.
This bit is cleared in all other conditions.
I2C master busy status bit.
Set to 1 when the master is busy processing a transaction.
Cleared if the master is ready or if another master device has control of the bus.
I2C arbitration lost status bit.
This bit is set to 1 when the I2C master is unsuccessful in gaining control of the I2C bus. If the I2CALENI bit in
I2CxMCTL is set, an interrupt is generated when the I2CAL bit is set.
This bit is cleared in all other conditions.
I2C master no acknowledge address bit.
This bit is set to 1 when a no acknowledge condition is received by the master in response to an address. If the
I2CNACKENI bit in I2CxMCTL is set, an interrupt is generated when the I2CMNA bit is set.
This bit is cleared in all other conditions.
I2C master receive request bit.
This bit is set to 1 when data enters the Rx FIFO. If the I2CMRENI in I2CxMCTL is set, an interrupt is generated.
This bit is cleared in all other conditions.
I2C master transmit request bit.
This bit goes high if the transmitter (Tx) FIFO is empty or only contains one byte and the master has transmitted an
address + write. If the I2CMTENI bit in I2CxMCTL is set, an interrupt is generated when the I2CMTXQ bit is set.
This bit is cleared in all other conditions.
I2C master Tx FIFO status bits.
00 = I2C master Tx FIFO empty.
01 = one byte in master Tx FIFO.
10 = one byte in master Tx FIFO.
11 = I2C master Tx FIFO full.
Rev. 0 | Page 65 of 96
ADuC7121
I2C Master Receive Registers
I2C Address 0 Registers
This 8-bit MMR is the I2C master receive register.
This 8-bit MMR holds the 7-bit slave address + the read/write
bit when the master begins communicating with a slave.
Name:
I2C0MRX, I2C1MRX
Address:
0xFFFF0888, 0xFFFF0908
Default value:
0x00
Access:
Read only
I2C Master Transmit Registers
Name:
I2C0ADR0, I2C1ADR0
Address:
0xFFFF0898, 0xFFFF0918
Default value:
0x00
Access:
Read and write
This 8-bit MMR is the I2C master transmit register.
Table 90. I2CxADR0 MMR in 7-Bit Address Mode
Name:
I2C0MTX, I2C1MTX
Bit
7:1
Name
I2CADR
Address:
0xFFFF088C, 0xFFFF090C
0
R/W
Default value:
0x00
Access:
Write only
Description
These bits contain the 7-bit address of the
required slave device.
Bit 0 is the read/write bit.
When this bit = 1, a read sequence is
requested.
When this bit = 0, a write sequence is
requested.
I2C Master Read Count Registers
This 16-bit MMR holds the required number of bytes when the
master begins a read sequence from a slave device.
Name:
I2C0MCNT0, I2C1MCNT0
Address:
0xFFFF0890, 0xFFFF0910
Default value:
0x0000
Access:
Read and write
Table 89. I2CxMCNT0 MMR Bit Descriptions
Bit
15:9
8
Name
I2CRECNT
Description
Reserved.
Set this bit if greater than 256 bytes are
required from the slave.
Clear this bit when reading 256 bytes or less.
These 8 bits hold the number of bytes
required during a slave read sequence,
minus 1. If only a single byte is required, set
these bits to 0.
Table 91. I2CxADR0 MMR in 10-Bit Address Mode
Bit
7:3
Name
2:1
I2CMADR
0
R/W
Description
These bits must be set to [11110b] in 10-bit
address mode.
These bits contain ADDR[9:8] in 10-bit
addressing mode.
Read/write bit.
When this bit = 1, a read sequence is
requested.
When this bit = 0, a write sequence is
requested.
I2C Address 1 Register
This 8-bit MMR is used in 10-bit addressing mode only. This
register contains the least significant byte of the address.
Name:
I2C0ADR1, I2C1ADR1
Address:
0xFFFF089C, 0xFFFF091C
Default value:
0x00
I2C Master Current Read Count Registers
Access:
Read and write
This 8-bit MMR holds the number of bytes received so far
during a read sequence with a slave device.
Table 92. I2CxADR1 MMR in 10-Bit Address Mode
7:0
I2CRCNT
Name:
I2C0MCNT1, I2C1MCNT1
Address:
0xFFFF0894, 0xFFFF0914
Default value:
0x00
Access:
Read only
Bit
7:0
Rev. 0 | Page 66 of 96
Name
I2CLADR
Description
These bits contain ADDR[7:0] in 10-bit
addressing mode.
ADuC7121
I2C Master Clock Control Register
This MMR controls the frequency of the I2C clock generated by
the master on to the SCL pin.
I2C Slave Registers
I2C Slave Control Register
This 16-bit MMR configures the I2C peripheral in slave mode.
Name:
I2C0DIV, I2C1DIV
Name:
I2C0SCTL, I2C1SCTL
Address:
0xFFFF08A4, 0xFFFF0924
Address:
0xFFFF08A8, 0xFFFF0928
Default value:
0x1F1F
Default value:
0x0000
Access:
Read and write
Access:
Read and write
Table 93. I2CxDIV MMR
Bit
15:8
Name
DIVH
7:0
DIVL
Description
These bits control the duration of the high
period of SCL.
These bits control the duration of the low period
of SCL.
Rev. 0 | Page 67 of 96
ADuC7121
Preliminary Technical Data
Table 94. I2CxSCTL MMR Bit Designations
Bit
15:11
10
Name
9
I2CSRXENI
8
I2CSSENI
7
I2CNACKEN
6
I2CSSEN
5
I2CSETEN
4
I2CGCCLR
3
I2CHGCEN
2
I2CGCEN
1
0
Reserved
I2CSEN
I2CSTXENI
Description
Reserved bits.
Slave transmit interrupt enable bit.
Set this bit to enable an interrupt after a slave transmits a byte.
Clear this interrupt source.
Slave receive interrupt enable bit.
Set this bit to enable an interrupt after the slave receives data.
Clear this interrupt source.
I2C stop condition detected interrupt enable bit.
Set this bit to enable an interrupt on detecting a stop condition on the I2C bus.
Clear this interrupt source.
I2C no acknowledge enable bit.
Set this bit to no acknowledge the next byte in the transmission sequence.
Clear this bit to let the hardware control the acknowledge/no acknowledge sequence.
I2C slave SCL stretch enable bit.
Set this bit to 1 to enable clock stretching. When SCL is low, setting this bit forces the device to hold SCL low until
I2CSSEN is cleared. If SCL is high, setting this bit forces the device to hold SCL low after the next falling edge.
Clear this bit to disable clock stretching.
I2C early transmit interrupt enable bit.
Setting this bit enables a transmit request interrupt just after the positive edge of SCL during the read bit
transmission.
Clear this bit to enable a transmit request interrupt just after the negative edge of SCL during the read bit
transmission.
I2C general call status and ID clear bit.
Writing a 1 to this bit clears the general call status and ID bits in the I2CxSSTA register.
Clear this bit at all other times.
I2C hardware general call enable. Hardware general call enable. When this bit and Bit 2 are set, and having received a
general call (Address 0x00) and a data byte, the device checks the contents of the I2CALT against the receive register.
If the contents match, the device has received a hardware general call. This is used if a device needs urgent attention
from a master device without knowing which master it needs to turn to. This is a “to whom it may concern” call. The
ADuC7121 watches for these addresses. The device that requires attention embeds its own address into the
message. All masters listen, and the one that can handle the device contacts its slave and acts appropriately. The LSB
of the I2CxALT register should always be written to 1, as per the I2C January 2000 bus specification.
Set this bit and I2CGCEN to enable hardware general call recognition in slave mode.
Clear to disable recognition of hardware general call commands.
I2C general call enable. Set this bit to enable the slave device to acknowledge an I2C general call, Address 0x00
(write). The device then recognizes a data bit. If it receives a 0x06 (reset and write programmable part of the slave
address by hardware) as the data byte, the I2C interface resets as per the I2C January 2000 bus specification. This
command can be used to reset an entire I2C system. If it receives a 0x04 (write programmable part of the slave
address by hardware) as the data byte, the general call interrupt status bit sets on any general call. The user must
take corrective action by reprogramming the device address.
Set this bit to allow the slave acknowledge I2C general call commands.
Clear to disable recognition of general call commands.
Always set this bit to 0.
I2C slave enable bit.
Set by the user to enable I2C slave mode.
Clear to disable I2C slave mode.
Rev. 0 | Page 68 of 96
ADuC7121
I2C Slave Status Registers
These 16-bit MMRs are the I2C status registers in slave mode.
Name:
I2C0SSTA, I2C1SSTA
Address:
0xFFFF08AC, 0xFFFF092C
Default value:
0x0000, 0x0000
Access:
Read and write
Table 95. I2CxSSTA MMR Bit Designations
Bit
15
14
Name
13
I2CREPS
12:11
I2CID[1:0]
10
I2CSS
9:8
I2CGCID[1:0]
7
I2CGC
6
I2CSBUSY
5
I2CSNA
I2CSTA
Description
Reserved bit.
This bit is set to 1 if:
A start condition followed by a matching address is detected.
A start byte (0x01) is received.
General calls are enabled and a general call code of (0x00) is received.
This bit is cleared on receiving a stop condition.
This bit is set to 1 if a repeated start condition is detected.
This bit is cleared on receiving a stop condition.
I2C address matching register. These bits indicate which I2CxIDx register matches the received address.
[00] = Received address matches I2CxID0.
[01] = Received address matches I2CxID1.
[10] = Received address matches I2CxID2.
[11] = Received address matches I2CxID3.
I2C stop condition after start detected bit.
This bit is set to 1 when a stop condition is detected after a previous start and matching address. When the I2CSSENI
bit in I2CxSCTL is set, an interrupt is generated.
This bit is cleared by reading this register.
I2C general call ID bits.
[00] = no general call received.
[01] = general call reset and program address.
[10] = general program address.
[11] = general call matching alternative ID.
Clear these bits by writing a 1 to the I2CGCCLR bit in I2CxSCTL. Note that these bits are not cleared by a general call
reset command.
I2C general call status bit.
This bit is set to 1 if the slave receives a general call command of any type. If the command received was a reset
command, all registers return to their default state. If the command received was a hardware general call, the Rx
FIFO holds the second byte of the command and this can be compared with the I2CxALT register.
Clear this bit by writing a 1 to the I2CGCCLR bit in I2CxSCTL.
I2C slave busy status bit.
Set to 1 when the slave receives a start condition.
Cleared by hardware under the following conditions:
The received address does not match any of the I2CxIDx registers.
The slave device receives a stop condition.
A repeated start address does not match any of the I2CxIDx registers.
I2C slave no acknowledge data bit.
This bit sets to 1 when the slave responds to a bus address with a no acknowledge. This bit is asserted under the
following conditions:
If no acknowledge was returned because there was no data in the Tx FIFO.
If the I2CNACKEN bit was set in the I2CxSCTL register.
This bit is cleared in all other conditions.
Rev. 0 | Page 69 of 96
ADuC7121
Bit
4
Name
I2CSRxFO
3
I2CSRXQ
2
I2CSTXQ
1
I2CSTFE
0
I2CETSTA
Description
Slave Rx FIFO overflow.
This bit is set to 1 when a byte is written to the Rx FIFO when it is already full.
This bit is cleared in all other conditions.
I2C slave receive request bit.
This bit is set to 1 when the Rx FIFO of the slave is not empty. This bit causes an interrupt to occur if the I2CSRXENI
bit in I2CxSCTL is set.
The Rx FIFO must be read or flushed to clear this bit.
I2C slave transmit request bit.
This bit is set to 1 when the slave receives a matching address followed by a read.
If the I2CSETEN bit in I2CxSCTL is = 0, this bit goes high just after the negative edge of SCL during the read bit
transmission.
If the I2CSETEN bit in I2CxSCTL is = 1, this bit goes high just after the positive edge of SCL during the read bit
transmission. This bit causes an interrupt to occur if the I2CSTXENI bit in I2CxSCTL is set.
This bit is cleared in all other conditions.
I2C slave FIFO underflow status bit.
This bit is high if the Tx FIFO is empty when a master requests data from the slave. This bit asserts at the rising edge
of SCL during the read bit.
This bit clears in all other conditions.
I2C slave early transmit FIFO status bit.
If the I2CSETEN bit in I2CxSCTL is = 0, this bit goes high if the slave Tx FIFO is empty.
If the I2CSETEN bit in I2CxSCTL is = 1, this bit goes high just after the positive edge of SCL during the write bit
transmission. This bit asserts once only for a transfer.
This bit is cleared after being read.
Rev. 0 | Page 70 of 96
ADuC7121
I2C Slave Receive Registers
Name:
I2C0ID2
Address:
0xFFFF08C4
Default value:
0x00
Access:
Read and write
Name:
I2C0ID3
I2C Slave Transmit Registers
Address:
0xFFFF08C8
This 8-bit MMR is the I2C slave transmit register.
Default value:
0x00
Name:
I2C0STX, I2C1STX
Access:
Read and write
Address:
0xFFFF08B4, 0xFFFF0934
Default value:
0x00
Name:
I2C1ID0
Access:
Write only
Address:
0xFFFF093C
Default value:
0x00
Access:
Read and write
Name:
I2C1ID1
Address:
0xFFFF0940
Default value:
0x00
Access:
Read and write
Name:
I2C1ID2
Address:
0xFFFF0944
2
This 8-bit MMR is the I C slave receive register.
Name:
I2C0SRX, I2C1SRX
Address:
0xFFFF08B0, 0xFFFF0930
Default value:
0x00
Access:
Read only
I2C Hardware General Call Recognition Registers
This 8-bit MMR is used with hardware general calls when
I2CxSCTL bit 3 is set to 1. This register is used in cases where a
master is unable to generate an address for a slave, and instead,
the slave must generate the address for the master.
Name:
I2C0ALT, I2C1ALT
Address:
0xFFFF08B8, 0xFFFF0938
Default value:
0x00
Access:
Read and write
I2C Slave Device ID Registers
I2C0IDx Registers
Default value:
0x00
These eight I2C0IDx 8-bit MMRs are programmed with I2C bus
IDs of the slave. See the section I2C Bus Addresses for further
details.
Access:
Read and write
Name:
I2C0ID0
Name:
I2C1ID3
Address:
0xFFFF08BC
Address:
0xFFFF0948
Default value:
0x00
Default value:
0x00
Access:
Read and write
Access:
Read and write
Name:
I2C0ID1
Address:
0xFFFF08C0
Default value:
0x00
Access:
Read and write
Rev. 0 | Page 71 of 96
ADuC7121
I2C COMMON REGISTERS
Table 96. I2CxFSTA MMR Bit Designations
2
I C FIFO Status Registers
These 16-bit MMRs contain the status of the Rx/Tx FIFOs in
both master and slave modes.
Name:
I2C0FSTA
Address:
0xFFFF08CC
Default value:
0x0000
Access:
Read and write
Name:
I2C1FSTA
Address:
0xFFFF094C
Default value:
0x0000
Access:
Read and write
Bit
15:10
9
8
7:6
Name
5:4
I2CMTXSTA
3:2
I2CSRXSTA
1:0
I2CSTXSTA
Rev. 0 | Page 72 of 96
I2CFMTX
I2CFSTX
I2CMRXSTA
Description
Reserved bits.
Set this bit to 1 to flush the master Tx FIFO.
Set this bit to 1 to flush the slave Tx FIFO.
I2C master receive FIFO status bits.
[00] = FIFO empty.
[01] = byte written to FIFO.
[10] = one byte in FIFO.
[11] = FIFO full.
I2C master transmit FIFO status bits.
[00] = FIFO empty.
[01] = byte written to FIFO.
[10] = one byte in FIFO.
[11] = FIFO full.
I2C slave receive FIFO status bits.
[00] = FIFO empty.
[01] = byte written to FIFO.
[10] = one byte in FIFO.
[11] = FIFO full.
I2C slave transmit FIFO status bits.
[00] = FIFO empty.
[01] = byte written to FIFO.
[10] = one byte in FIFO.
[11] = FIFO full.
ADuC7121
SERIAL PERIPHERAL INTERFACE
important that the polarity and phase are configured the same
for the master and slave devices.
The ADuC7121 integrates a complete hardware serial peripheral interface (SPI) on-chip. SPI is an industry standard,
synchronous serial interface that allows eight bits of data to
be synchronously transmitted and simultaneously received,
that is, full duplex up to a maximum bit rate of 20 Mbps.
SPI CHIP SELECT INPUT PIN
The SPI port can be configured for master or slave operation
and typically consists of four pins: P0.3/MISO/PLAO[12]/SYNC,
P0.4/MOSI/PLAI[11]/TRIP, P0.2/SPICLK/ADCBUSY/PLAO[13],
and P0.5/CS/PLAI[10]/ ADCCONVST.
SPI MISO (MASTER IN, SLAVE OUT) PIN
MISO on the P0.3/MISO/PLAO[12]/SYNC pin is configured as
an input line in master mode and an output line in slave mode.
Connect the MISO line on the master (data in) to the MISO line
in the slave device (data out). The data is transferred as byte
wide (8-bit) serial data, MSB first.
In SPI master mode, CS is an active low output signal. It asserts
itself automatically at the beginning of a transfer and deasserts
itself upon completion.
CONFIGURING EXTERNAL PINS FOR SPI
FUNCTIONALITY
The SPI pins of the ADuC7121 device are P0.2 to P0.5.
•
SPI MOSI (MASTER OUT, SLAVE IN) PIN
MOSI on the P0.4/MOSI/PLAI[11]/TRIP pin is configured as
an output line in master mode and an input line in slave mode.
The MOSI line on the master (data out) should be connected to
the MOSI line in the slave device (data in). The data is transferred
as byte wide (8-bit) serial data, MSB first.
SPICLK (SERIAL CLOCK I/O) PIN
The master serial clock (SPICLK) synchronizes the data being
transmitted and received through the MOSI SPICLK period.
Therefore, a byte is transmitted/received after eight SPICLK
periods. The P0.2/SPICLK/ADCBUSY/PLAO[13] pin is configured
as an output in master mode and as an input in slave mode.
In master mode, the polarity and phase of the clock are controlled
by the SPICON register, and the bit rate is defined in the SPIDIV
register as follows:
f SERIAL CLOCK =
In SPI slave mode, a transfer is initiated by the assertion of CS
on the P0.5/CS/PLAI[10]/ADCCONVST pin. CS is an active low
input signal. The SPI port then transmits and receives 8-bit data
until the transfer is concluded by deassertion of CS. In slave
mode, CS is always an input.
•
•
•
P0.5/CS/PLAI[10]/ADCCONVST is the slave chip select pin. In
slave mode, this pin is an input and must be driven low by
the master. In master mode, this pin is an output and goes
low at the beginning of a transfer and high at the end of a
transfer.
P0.2/SPICLK/ADCBUSY/PLAO[13] is the SPICLK pin.
P0.3/MISO/PLAO[12]/SYNC is the master in, slave out pin.
P0.4/MOSI/PLAI[11]/TRIP is the master out, slave in pin.
To configure P0.2 to P0.5 for SPI mode, see the
General-Purpose Input/Output section.
SPI REGISTERS
The following MMR registers control the SPI interface: SPISTA,
SPIRX, SPITX, SPIDIV, and SPICON.
SPI Status Register
This 32-bit MMR contains the status of the SPI interface in both
master and slave modes.
f UCLK
2 × (1 + SPIDIV)
The maximum speed of the SPI clock is independent on the
clock divider bits.
In slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 10 Mbps.
Name:
SPISTA
Address:
0xFFFF0A00
Default value:
0x0000
Access:
Read only
In both master and slave modes, data is transmitted on one edge
of the SPICLK signal and sampled on the other. Therefore, it is
Rev. 0 | Page 73 of 96
ADuC7121
Table 97. SPISTA MMR Bit Designations
Bit
15:12
11
Name
10:8
SPIRXFSTA[2:0]
7
SPIFOF
6
SPIRXIRQ
5
SPITXIRQ
4
SPITXUF
3:1
SPITXFSTA[2:0]
0
SPIISTA
SPIREX
Description
Reserved bits.
SPI Rx FIFO excess bytes present. This bit is set when there are more bytes in the Rx FIFO than indicated in the
SPIMDE bits in SPICON.
This bit is cleared when the number of bytes in the FIFO is equal or less than the number in SPIMDE.
SPI Rx FIFO status bits.
[000] = Rx FIFO is empty.
[001] = one valid byte in the FIFO.
[010] = two valid bytes in the FIFO.
[011] = three valid bytes in the FIFO.
[100] = four valid bytes in the FIFO.
SPI Rx FIFO overflow status bit.
Set when the Rx FIFO was already full when new data was loaded to the FIFO. This bit generates an interrupt
except when SPIRFLH is set in SPICON.
Cleared when the SPISTA register is read.
SPI Rx IRQ status bit.
Set when a receive interrupt occurs. This bit is set when SPITMDE in SPICON is cleared and the required
number of bytes have been received.
Cleared when the SPISTA register is read.
SPI Tx IRQ status bit.
Set when a transmit interrupt occurs. This bit is set when SPITMDE in SPICON is set and the required number
of bytes have been transmitted.
Cleared when the SPISTA register is read.
SPI Tx FIFO underflow.
This bit is set when a transmit is initiated without any valid data in the Tx FIFO. This bit generates an interrupt
except when SPITFLH is set in SPICON.
Cleared when the SPISTA register is read.
SPI Tx FIFO status bits.
[000] = Tx FIFO is empty.
[001] = one valid byte in the FIFO.
[010] = two valid bytes in the FIFO.
[011] = three valid bytes in the FIFO.
[100] = four valid bytes in the FIFO.
SPI interrupt status bit.
Set to 1 when an SPI based interrupt occurs.
Cleared after reading SPISTA.
SPIRX Register
SPIDIV Register
This 8-bit MMR is the SPI receive register.
This 8-bit MMR is the SPI baud rate selection register.
Name:
SPIRX
Name:
SPIDIV
Address:
0xFFFF0A04
Address:
0xFFFF0A0C
Default value:
0x00
Default value:
0x00
Access:
Read only
Access:
Read and write
SPITX Register
SPI Control Register
This 8-bit MMR is the SPI transmit register.
This 16-bit MMR configures the SPI peripheral in both master
and slave modes.
Name:
SPITX
Address:
0xFFFF0A08
Default value:
0x00
Access:
Write only
Name:
SPICON
Address:
0xFFFF0A10
Default value:
0x0000
Access:
Read and write
Rev. 0 | Page 74 of 96
ADuC7121
Table 98. SPICON MMR Bit Designations
Bit
15:14
Name
SPIMDE
13
SPITFLH
12
SPIRFLH
11
SPICONT
10
SPILP
9
SPIOEN
8
SPIROW
7
SPIZEN
6
SPITMDE
5
SPILF
4
SPIWOM
3
SPICPO
2
SPICPH
1
SPIMEN
0
SPIEN
Description
SPI IRQ mode bits. These bits configure when the Tx/Rx interrupts occur in a transfer.
[00] = Tx interrupt occurs when one byte has been transferred. Rx interrupt occurs when one or more bytes have been
received into the FIFO.
[01] = Tx interrupt occurs when two bytes has been transferred. Rx interrupt occurs when two or more bytes have been
received into the FIFO.
[10] = Tx interrupt occurs when three bytes has been transferred. Rx interrupt occurs when three or more bytes have
been received into the FIFO.
[11] = Tx interrupt occurs when four bytes has been transferred. Rx interrupt occurs when the Rx FIFO is full, or four
bytes present.
SPI Tx FIFO flush enable bit.
Set this bit to flush the Tx FIFO. This bit does not clear itself and should be toggled if a single flush is required. If this bit
is left high, then either the last transmitted value or 0x00 is transmitted depending on the SPIZEN bit. Any writes to the
Tx FIFO are ignored while this bit is set.
Clear this bit to disable Tx FIFO flushing.
SPI Rx FIFO flush enable bit.
Set this bit to flush the Rx FIFO. This bit does not clear itself and should be toggled if a single flush is required. If this bit
is set, all incoming data is ignored and no interrupts are generated. If this bit is set and SPITMDE = 0, a read of the Rx
FIFO initiates a transfer.
Clear this bit to disable Rx FIFO flushing.
Continuous transfer enable.
Set by the user to enable continuous transfer. In master mode, the transfer continues until no valid data is available in
the Tx register. The P0.5/CS/PLAI[10]/ADCCONVST pin is asserted and remains asserted for the duration of each 8-bit serial
transfer until Tx is empty.
Cleared by the user to disable continuous transfer. Each transfer consists of a single 8-bit serial transfer. If valid data
exists in the SPITX register, then a new transfer is initiated after a stall period of one serial clock cycle.
Loopback enable bit.
Set by the user to connect MISO to MOSI and test software.
Cleared by the user to be in normal mode.
Slave MISO output enable bit.
Set this bit for normal operation of MISO.
Clear this bit to disable the output driver on the MISO pin. The MISO pin is open drain when this bit is clear.
SPIRX overflow overwrite enable.
Set by the user, the valid data in the Rx register is overwritten by the new serial byte that is received.
Cleared by the user, the new serial byte that is received is discarded.
SPI transmits zeros when Tx FIFO is empty.
Set this bit to transmit 0x00 when there is no valid data in the Tx FIFO.
Clear this bit to transmit the last transmitted value when there is no valid data in the Tx FIFO.
SPI transfer and interrupt mode.
Set by the user to initiate a transfer with a write to the SPITX register. Interrupt occurs only when Tx is empty.
Cleared by the user to initiate a transfer with a read of the SPIRX register. Interrupt occurs only when Rx is full.
LSB first transfer enable bit.
Set by the user, the LSB is transmitted first.
Cleared by the user, the MSB is transmitted first.
SPI wired or mode enable bit.
Set to 1 to enable open-drain data output enable. External pull-ups are required on data output pins.
Clear for normal output levels.
Serial clock polarity mode bit.
Set by the user, the serial clock idles high.
Cleared by the user, the serial clock idles low.
Serial clock phase mode bit.
Set by the user, the serial clock pulses at the beginning of each serial bit transfer.
Cleared by the user, the serial clock pulses at the end of each serial bit transfer.
Master mode enable bit.
Set by the user to enable master mode.
Cleared by the user to enable slave mode.
SPI enable bit.
Set by the user to enable the SPI.
Cleared by the user to disable the SPI.
Rev. 0 | Page 75 of 96
ADuC7121
PROGRAMMABLE LOGIC ARRAY (PLA)
The ADuC7121 integrates a fully programmable logic array (PLA)
that consists of two independent but interconnected PLA blocks.
Each block consists of eight PLA elements, giving each part a
total of 16 PLA elements.
Each PLA element contains a dual input lookup table that can
be configured to generate any logic output function based on
two inputs and a flip-flop. This is represented in Figure 36.
0
2
4
A
The PLA is configured via a set of user MMRs. The output(s)
of the PLA can be routed to the internal interrupt system, to
the ADCCONVST signal of the ADC, to an MMR, or to any of the
16 PLA output pins.
The two blocks can be interconnected as follows:
LOOKUP
TABLE
3
to be configured in the GPxCON register as PLA pins before using
the PLA. Note that the comparator output is also included as
one of the 16 input pins, and that the JTAG TDI and TDO pins
are included as PLA outputs. If you want to use JTAG programming or debugging, then you cannot use the JTAG TDI and
TDO pins as PLA outputs.
B
•
1
09492-036
•
Output of Element 15 (Block 1) can be fed to Input 0 of
Mux 0 of Element 0 (Block 0).
Output of Element 7 (Block 0) can be fed to the Input 0 of
Mux 0 of Element 8 (Block 1).
Figure 36. PLA Element
In total, 32 GPIO pins are available on each ADuC7121 for the
PLA. These include 16 input pins and 16 output pins, which need
Table 99. Element Input/Output
Element
0
1
2
3
4
5
6
7
PLA Block 0
Input
P2.7
P2.2
P0.6
P0.7
P0.1
P0.0
P1.1
P1.0
Output
P3.0
P3.1
P3.2
P3.3
P1.7
P1.6
P2.5
P2.4
Element
8
9
10
11
12
13
14
15
Rev. 0 | Page 76 of 96
PLA Block 1
Input
P1.4
P1.5
P0.5
P0.4
P2.1
P2.0
P2.3
P2.6
Output
P3.4
P3.5
P3.6
P3.7
P0.3
P0.2
P1.3
P1.2
ADuC7121
PLA MMRS INTERFACE
Table 101. PLAELMx MMR Bit Descriptions
The PLA peripheral interface consists of the 21 MMRs
described in the following sections.
PLAELMx Registers
PLAELMx are Element 0 to Element 15 control registers. They
configure the input and output mux of each element, select the
function in the look-up table, and bypass/use the flip-flop. See
Table 101 and Table 104.
Table 100. PLAELMx MMR Addresses (Default Value =
0x0000, Access is Read/Write)
Name
PLAELM0
PLAELM1
PLAELM2
PLAELM3
PLAELM4
PLAELM5
PLAELM6
PLAELM7
PLAELM8
PLAELM9
PLAELM10
PLAELM11
PLAELM12
PLAELM13
PLAELM14
PLAELM15
Bit
31:11
10:9
8:7
6
Value
5
Address
0xFFFF0B00
0xFFFF0B04
0xFFFF0B08
0xFFFF0B0C
0xFFFF0B10
0xFFFF0B14
0xFFFF0B18
0xFFFF0B1C
0xFFFF0B20
0xFFFF0B24
0xFFFF0B28
0xFFFF0B2C
0xFFFF0B30
0xFFFF0B34
0xFFFF0B38
0xFFFF0B3C
4:1
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
0
Description
Reserved.
Mux 0 control (see Table 104).
Mux 1 control (see Table 104).
Mux 2 control.
Set by the user to select the output of Mux 0.
Cleared by the user to select the bit value from
PLADIN.
Mux 3 control.
Set by the user to select the input pin of the
particular element.
Cleared by the user to select the output of Mux 1.
Look up table control.
0.
NOR.
B AND NOT A.
NOT A.
A AND NOT B.
NOT B.
EXOR.
NAND.
AND.
EXNOR.
B.
NOT A OR B.
A.
A OR NOT B.
OR.
1.
Mux 4 control.
Set by the user to bypass the flip-flop.
Cleared by the user to select the flip-flop
(cleared by default).
Table 102. Feedback Configuration
Bit
10:9
8:7
Value
00
01
10
11
00
01
10
11
PLAELM0
Element 15
Element 2
Element 4
Element 6
Element 1
Element 3
Element 5
Element 7
PLAELM1 to PLAELM7
Element 0
Element 2
Element 4
Element 6
Element 1
Element 3
Element 5
Element 7
Rev. 0 | Page 77 of 96
PLAELM8
Element 7
Element 10
Element 12
Element 14
Element 9
Element 11
Element 13
Element 15
PLAELM9 to PLAELM15
Element 8
Element 10
Element 12
Element 14
Element 9
Element 11
Element 13
Element 15
ADuC7121
PLACLK Register
PLACLK is the clock selection for the flip-flops of Block 0 and
Block 1. The maximum frequency when using the GPIO pins as
the clock input for the PLA blocks is 41.78 MHz.
Name:
PLACLK
Address:
0xFFFF0B40
Default value:
0x00
Access:
Read and write
Bit
11:8
Value
Description
PLA IRQ1 source.
PLA Element 0.
PLA Element 1.
PLA Element 15.
Reserved.
PLA IRQ0 enable bit.
Set by the user to enable IRQ0 output from
the PLA.
Cleared by the user to disable IRQ0 output
from the PLA.
PLA IRQ0 source.
PLA Element 0.
PLA Element 1.
PLA Element 15.
0000
0001
1111
7:5
4
3:0
0000
0001
1111
Table 103. PLACLK MMR Bit Descriptions
Bit
7
6:4
Value
000
001
010
011
100
101
Other
3
2:0
000
001
010
011
100
101
Other
Description
Reserved.
Block 1 clock source selection.
GPIO clock on P0.5 of the P0.5/CS/PLAI[10]/
ADCCONVST pin.
PLAADC Register
PLAADC is the PLA source for the ADC start conversion signal.
GPIO clock on P0.0 of the P0.0/SCL0/PLAI[5] pin.
GPIO clock on the P0.7 of the P0.7/TRST/PLAI[3] pin.
HCLK (core clock).
OCLK (32.768 kHz external crystal).
Timer1 overflow.
Reserved.
Reserved.
Block 0 clock source selection.
GPIO clock on P0.5. on P0.5 of the P0.5/CS/
PLAI[10]/ADCCONVST pin.
GPIO clock on P0.0 of the P0.0/SCL0/PLAI[5] pin.
GPIO clock on P0.7 of the P0.7/TRST/PLAI[3] pin.
HCLK (core clock).
OCLK (32.768 kHz external crystal).
Timer1 overflow.
Reserved.
Name:
PLAADC
Address:
0xFFFF0B48
Default value:
0x00000000
Access:
Read and write
Table 105. PLAADC MMR Bit Descriptions
Bit
31:5
4
Value
Description
Reserved.
ADC start conversion enable bit.
Set by the user to enable an ADC start
conversion from the PLA.
Cleared by the user to disable an ADC start
conversion from the PLA.
ADC start conversion source.
PLA Element 0.
PLA Element 1.
PLA Element 15.
3:0
0000
0001
1111
PLAIRQ Register
PLAIRQ enables IRQ0 and/or IRQ1 and selects the source
of the normal interrupt request IRQ (IRQ).
PLADIN Register
Name:
PLAIRQ
Address:
0xFFFF0B44
Default value:
0x0000
Access:
Read and write
PLADIN is a data input MMR for PLA.
Name:
PLADIN
Address:
0xFFFF0B4C
Default value:
0x00000000
Table 104. PLAIRQ MMR Bit Descriptions
Access:
Read and write
Bit
15:13
12
Table 106. PLADIN MMR Bit Descriptions
Value
Description
Reserved.
PLA IRQ1 enable bit.
Set by the user to enable IRQ1 output from
the PLA.
Cleared by the user to disable IRQ1 output
from the PLA.
Bit
31:16
15:0
Rev. 0 | Page 78 of 96
Description
Reserved.
Input bit from Element 15 to Element 0.
ADuC7121
PLADOUT Register
PLALCK Register
PLADOUT is a data output MMR for PLA. This register is
always updated.
Name:
PLADOUT
PLALCK is a PLA lock option. Bit 0 is written only once. When
set, it does not allow modifying any of the PLA MMRs, except
PLADIN. A PLA tool is provided in the development system to
easily configure the PLA.
Address:
0xFFFF0B50
Name:
PLALCK
Default value:
0x00000000
Address:
0xFFFF0B54
Access:
Read only
Default value:
0x00
Access:
Write only
Table 107. PLADOUT MMR Bit Descriptions
Bit
31:16
15:0
Description
Reserved.
Output bit from Element 15 to Element 0.
Rev. 0 | Page 79 of 96
ADuC7121
INTERRUPT SYSTEM
Table 108. IRQ/FIQ MMRs Bit Designations
Bit
0
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Description
All interrupts OR’ed (FIQ only)
Software interrupt
Timer0
Timer1
Timer2 or wake-up timer
Timer3 or watchdog timer
Timer4
IDAC fault
PSM
Undefined
Flash Control 0
Flash Control 1
ADC
UART
SPI
I2C0 Master IRQ
I2C0 Slave IRQ
I2C1 Master IRQ
I2C1 Slave IRQ
XIRQ0 (GPIO IRQ0 )
XIRQ1 (GPIO IRQ1)
XIRQ2 (GPIO IRQ2 )
XIRQ3 (GPIO IRQ3)
PWM
XIRQ4 (GPIO IRQ4 )
XIRQ5 (GPIO IRQ5)
PLA IRQ0
PLA IRQ1
Comments
This bit is set if any FIQ is active
User programmable interrupt source
General-Purpose Timer0
General-Purpose Timer1
General-Purpose Timer2 or wake-up timer
General-Purpose Timer3 or watchdog timer
General-Purpose Timer4
IDAC fault IRQ
Power supply monitor
This bit is not used
Flash controller for Block 0 interrupt
Flash controller for Block 1 interrupt
ADC interrupt source bit
UART interrupt source bit
SPI interrupt source bit
I2C master interrupt source bit
I2C slave interrupt source bit
I2C master interrupt source bit
I2C slave interrupt source bit
External Interrupt 0
External Interrupt 1
External Interrupt 2
External Interrupt 3
PWM trip interrupt source bit
External Interrupt 4
External Interrupt 5
PLA Block 0 IRQ bit
PLA Block 1 IRQ bit
Upon entering the interrupt service routine (ISR), immediately
save IRQSTA/FIQSTA to ensure that all valid interrupt sources
are serviced.
There are 27 interrupt sources on the ADuC7121 that are controlled by the interrupt controller. All interrupts are generated
from the on-chip peripherals, except for the software interrupt
(SWI), which is programmable by the user. The ARM7TDMI
CPU core recognizes interrupts as one of two types only: a
normal interrupt request (IRQ) and a fast interrupt request
(FIQ). All the interrupts can be masked separately.
NORMAL INTERRUPT REQUEST (IRQ)
The control and configuration of the interrupt system is managed
through a number of interrupt related registers. The bits in each
IRQ and FIQ register represent the same interrupt source as
described in Table 108.
All 32 bits are logically OR’ed to create a single IRQ signal to the
ARM7TDMI core. The four 32-bit registers dedicated to IRQ
follow.
The ADuC7121 contains a vectored interrupt controller (VIC)
that supports nested interrupts up to eight levels. The VIC also
allows the programmer to assign priority levels to all interrupt
sources. Interrupt nesting needs to be enabled by setting the
ENIRQN bit in the IRQCONN register. A number of extra
MMRs are used when the full-vectored interrupt controller is
enabled.
The normal interrupt request (IRQ) is the exception signal
to enter the IRQ mode of the processor. It services generalpurpose interrupt handling of internal and external events.
IRQSIG Register
IRQSIG reflects the status of the different IRQ sources. If a
peripheral generates an IRQ signal, the corresponding bit in
the IRQSIG is set; otherwise, it is cleared. The IRQSIG bits clear
when the interrupt in the particular peripheral is cleared. All
IRQ sources can be masked in the IRQEN MMR. IRQSIG is a
read-only register. Do not use this register in an interrupt service
routine for determining the source of an IRQ exception; use
only IRQSTA for this purpose.
Rev. 0 | Page 80 of 96
ADuC7121
Name:
IRQSIG
Name:
IRQSTA
Address:
0xFFFF0004
Address:
0xFFFF0000
Default value:
0x00000000
Default value:
0x00000000
Access:
Read only
Access:
Read only
IRQEN Register
IRQEN provides the value of the current enable mask. When
a bit is set to 1, the corresponding source request is enabled
to create an IRQ exception. When a bit is set to 0, the corresponding source request is disabled or masked, which does not
create an IRQ exception. The IRQEN register cannot be used to
disable an interrupt.
Name:
IRQEN
Address:
0xFFFF0008
Default value:
0x00000000
Access:
Read and write
IRQCLR is a write-only register that allows the IRQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the IRQEN register without
affecting the remaining bits. The pair of registers, IRQEN and
IRQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
Use this register to disable an interrupt source only when:
•
The device is in the interrupt sources interrupt service
routine.
The peripheral is temporarily disabled by its own control
register.
Do not use the IRQCLR to disable an IRQ source if that IRQ
source has an interrupt pending or could have an interrupt
pending.
Name:
IRQCLR
Address:
0xFFFF000C
Default value:
0x00000000
Access:
Write only
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface and provides the
second level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
Bit 31 to Bit 1 of FIQSTA are logically OR’ed to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
IRQCLR Register
•
FAST INTERRUPT REQUEST (FIQ)
The logic for FIQEN and FIQCLR does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN clears, as a side effect, the same bit in IRQEN. Likewise,
a bit set to 1 in IRQEN clears, as a side effect, the same bit in
FIQEN. An interrupt source can be disabled in both IRQEN
and FIQEN masks.
FIQSIG Register
FIQSIG reflects the status of the different FIQ sources. If a
peripheral generates an FIQ signal the corresponding bit in
the FIQSIG is set, otherwise it is cleared. The FIQSIG bits are
cleared when the interrupt in the particular peripheral is
cleared. All FIQ sources can be masked in the FIQEN MMR.
FIQSIG is read only.
Name:
FIQSIG
Address:
0xFFFF0104
Default value:
0x00000000
Access:
Read only
FIQEN Register
FIQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled
to create an FIQ exception. When a bit is set to 0, the corresponding source request is disabled or masked, which does not
create an FIQ exception. The FIQEN register cannot be used to
disable an interrupt.
IRQSTA Register
IRQSTA is a read-only register that provides the current enabled
IRQ source status (effectively a logic AND of the IRQSIG and
IRQEN bits). When set to 1, that source generates an active IRQ
request to the ARM7TDMI core. There is no priority encoder
or interrupt vector generation. This function is implemented in
software in a common interrupt handler routine.
FIQEN Register
Name:
FIQEN
Address:
0xFFFF0108
Default value:
0x00000000
Access:
Read and write
Rev. 0 | Page 81 of 96
ADuC7121
FIQCLR
Table 109. SWICFG MMR Bit Designations
FIQCLR is a write-only register that allows the FIQEN register
to clear to mask an interrupt source. Each bit that is set to 1
clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
Bit
31:3
2
1
Use this register to disable an interrupt source only when:
•
The device is in the interrupt sources interrupt service
routine.
The peripheral is temporarily disabled by its own control
register.
0
Any interrupt signal must be active for at least the minimum
interrupt latency time, to be detected by the interrupt controller
and to be detected by the user in the IRQSTA/FIQSTA register.
PROGRAMMABLE PRIORITY
PER INTERRUPT (IRQP0/IRQP1/IRQP2)
Do not use this register to disable an FIQ source if that FIQ
source has an interrupt pending or could have an interrupt
pending.
IRQ_SOURCE
FIQCLR Register
Name:
FIQCLR
Address:
0xFFFF010C
Default value:
0x00000000
Access:
Write only
FIQ_SOURCE
INTERNAL
ARBITER
LOGIC
POINTER TO
FUNCTION
(IRQVEC)
INTERRUPT VECTOR
BIT 31 TO BIT 22 TO BIT 7
BIT 23
(IRQBASE)
UNUSED
FIQSTA
FIQSTA is a read-only register that provides the current enabled
FIQ source status (effectively a logic AND of the FIQSIG and
FIQEN bits). When set to 1, that source generates an active FIQ
request to the ARM7TDMI core. There is no priority encoder
or interrupt vector generation. This function is implemented in
software in a common interrupt handler routine.
BIT 6 TO BIT 1 TO
BIT 2
BIT 0
HIGHEST
LSB
PRIORITY
ACTIVE IRQ
09492-037
•
Description
Reserved.
Programmed Interrupt FIQ. Setting/clearing this bit
corresponds to setting/clearing Bit 1 of FIQSTA and
FIQSIG.
Programmed Interrupt IRQ1. Setting or clearing this bit
corresponds to setting or clearing Bit 1 of IRQSTA and
IRQSIG.
Reserved.
Figure 37. Interrupt Structure
Vectored Interrupt Controller (VIC)
Name:
FIQSTA
Address:
0xFFFF0100
The ADuC7121 incorporates an enhanced interrupt control
system or vectored interrupt controller. The vectored interrupt
controller for IRQ interrupt sources is enabled by setting Bit 0
of the IRQCONN register. Similarly, Bit 1 of IRQCONN enables
the vectored interrupt controller for the FIQ interrupt sources.
The vectored interrupt controller provides the following
enhancements to the standard IRQ/FIQ interrupts:
Default value:
0x00000000
•
Access:
Read only
FIQSTA Register
Programmed Interrupts
Because the programmed interrupts are not maskable, they are
controlled by another register (SWICFG) that writes into both
IRQSTA and IRQSIG registers and/or the FIQSTA and FIQSIG
registers at the same time.
The 32-bit register dedicated to software interrupt is SWICFG
described in Table 109. This MMR allows the control of a
programmed source interrupt.
•
•
Rev. 0 | Page 82 of 96
Vectored interrupts—allows a user to define separate
interrupt service routine addresses for every interrupt
source. This is achieved by using the IRQBASE and
IRQVEC registers.
IRQ/FIQ interrupts—can be nested up to eight levels
depending on the priority settings. An FIQ still has a higher
priority than an IRQ. Therefore, if the VIC is enabled for both
the FIQ and IRQ and prioritization is maximized, it is
possible to have 16 separate interrupt levels.
Programmable interrupt priorities—using the IRQP0 to
IRQP3 registers, an interrupt source can be assigned an
interrupt priority level value between 0 and 7.
ADuC7121
VIC MMRs
Table 112. IRQP0 MMR Bit Designations
IRQBASE Register
Bit
31
30:28
Name
Reserved
IDAC_Fault
27
26:24
Reserved
T4PI
23
22:20
Reserved
T3PI
19
18:16
Reserved
T2PI
15
14:12
Reserved
T1PI
11
10:8
Reserved
T0PI
7
6:4
Reserved
SWINTP
3:0
Reserved
The vector base register, IRQBASE, is used to point to the start
address of memory used to store 32 pointer addresses. These
pointer addresses are the addresses of the individual interrupt
service routines.
Name:
IRQBASE
Address:
0xFFFF0014
Default value:
0x00000000
Access:
Read and write
Table 110. IRQBASE MMR Bit Designations
Bit
31:16
15:0
Type
Read only
Read and write
Initial Value
Reserved
0
Description
Always read as 0
Vector base address
IRQVEC Register
The IRQ interrupt vector register, IRQVEC points to a memory
address containing a pointer to the interrupt service routine of
the currently active IRQ. Read this register only when an IRQ
occurs and IRQ interrupt nesting has been enabled by setting
Bit 0 of the IRQCONN register.
Name:
IRQVEC
Address:
0xFFFF001C
Default value:
0x00000000
Access:
Read and write
Description
Reserved bit.
A priority level of 0 to 7 can be set for an
IDAC fault interrupt.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer4.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer3.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer2.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer1.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer0.
Reserved bit.
A priority level of 0 to 7 can be set for the
software interrupt source.
Reserved bit.
IRQP1 Register
Name:
IRQP1
Address:
0xFFFF0024
Default value:
0x00000000
Access:
Read and write
Table 113. IRQP1 MMR Bit Designations
Table 111. IRQVEC MMR Bit Designations
Bit
31:23
22:7
6:2
Type
Read only
Read and
write
Read only
1:0
Reserved
Initial
Value
0
0
0
0
Description
Always read as 0.
IRQBASE register value.
Highest priority source. This is a
value between 0 and 27
representing the possible
interrupt sources. For example, if
the highest currently active IRQ is
Timer2, these bits are [00100].
Reserved bits.
Priority Registers
IRQP0 Register
Name:
IRQP0
Address:
0xFFFF0020
Default value:
0x00000000
Access:
Read and write
Bit
31
30:28
Name
Reserved
I2C0MPI
27
26:24
23
22:20
19
18:16
Reserved
SPIPI
Reserved
UARTPI
Reserved
ADCPI
15
14:12
Reserved
Flash1PI
11
10:8
Reserved
Flash0PI
7:3
2:0
Reserved
PSMPI
Rev. 0 | Page 83 of 96
Description
Reserved bit.
A priority level of 0 to 7 can be set for I2C 0
master.
Reserved bit.
A priority level of 0 to 7 can be set for SPI.
Reserved bit.
A priority level of 0 to 7 can be set for UART.
Reserved bit.
A priority level of 0 to 7 can be set for the
ADC interrupt source.
Reserved bit.
A priority level of 0 to 7 can be set for the
Flash block 1 controller interrupt source.
Reserved bit.
A priority level of 0 to 7 can be set for the
Flash Block 0 controller interrupt source.
Reserved bits.
A priority level of 0 to 7 can be set for the
power supply monitor interrupt source.
ADuC7121
IRQP2 Register
IRQCONN Register
Name:
IRQP2
Address:
0xFFFF0028
Default value:
0x00000000
The IRQCONN register is the IRQ and FIQ control register. It
contains two active bits. The first to enable nesting and prioritization of IRQ interrupts the other to enable nesting and prioritization
of FIQ interrupts.
Access:
Read and write
If these bits are cleared, then FIQs and IRQs can still be used,
but it is not possible to nest IRQs or FIQs, nor is it possible to
set an interrupt source priority level. In this default state, an
FIQ does have a higher priority than an IRQ.
Table 114. IRQP2 MMR Bit Designations
Bit
31
30:28
27
26:24
23
22:20
19
18:16
15
14:12
11
10:8
Name
Reserved
PWMPI
Reserved
IRQ3PI
Reserved
IRQ2PI
Reserved
IRQ1PI
Reserved
IRQ0PI
Reserved
I2C1SPI
7
6:4
Reserved
I2C1MPI
3
2:0
Reserved
I2C0SPI
Description
Reserved bit.
A priority level of 0 to 7 can be set for PWM.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ3.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ2.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ1.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ0.
Reserved bit.
A priority level of 0 to 7 can be set for I2C1
slave.
Reserved bit.
A priority level of 0 to 7 can be set for I2C1
master.
Reserved bit.
A priority level of 0 to 7 can be set for I2C0
slave.
IRQP3 Register
Name:
IRQP3
Address:
0xFFFF002C
Default value:
0x00000000
Access:
Read and write
Name:
IRQCONN
Address:
0xFFFF0030
Default value:
0x00000000
Access:
Read and write
Table 115. IRQCONN MMR Bit Designations
Bit
31:2
Name
Reserved
1
ENFIQN
0
ENIRQN
Description
These bits are reserved and should not be
written to.
Setting this bit to 1 enables nesting of FIQ
interrupts. Clearing this bit means no nesting
or prioritization of FIQs is allowed.
Setting this bit to 1 enables nesting of IRQ
interrupts. Clearing this bit means no nesting
or prioritization of IRQs is allowed.
IRQSTAN Register
If IRQCONN.0 is asserted and IRQVEC is read then one of
these bits is asserted. The bit that asserts depends on the
priority of the IRQ. If the IRQ is of Priority 0 then Bit 0 asserts,
Priority 1 then Bit 1 asserts, and so forth. When a bit is set in
this register, all interrupts of that priority and lower are blocked.
To clear a bit in this register, all bits of a higher priority must be
cleared first. It is only possible to clear one bit at a time. For
example, if this register is set to 0x09 then writing 0xFF changes
the register to 0x08, and writing 0xFF a second time changes
the register to 0x00.
IRQP3 MMR Bit Designations
Bit
31:15
14:12
11
10:8
7
6:4
3
2:0
Name
Reserved
PLA1PI
Reserved
PLA0PI
Reserved
IRQ5PI
Reserved
IRQ4PI
Description
Reserved bit.
A priority level of 0 to 7 can be set for PLA0.
Reserved bit.
A priority level of 0 to 7 can be set for PLA0.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ5.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ4.
Name:
IRQSTAN
Address:
0xFFFF003C
Default value:
0x00000000
Access:
Read and write
Table 116. IRQSTAN MMR Bit Designations
Bit
31:8
7:0
Rev. 0 | Page 84 of 96
Name
Reserved
Description
These bits are reserved and should not be
written to.
Setting this bit to 1 enables nesting of FIQ
interrupts.
Clearing this bit means no nesting or
prioritization of FIQs is allowed.
ADuC7121
FIQVEC Register
The FIQ interrupt vector register, FIQVEC points to a memory
address containing a pointer to the interrupt service routine of
the currently active FIQ. Read this register only when an FIQ
occurs and FIQ interrupt nesting has been enabled by setting
Bit 1 of the IRQCONN register.
example if this register is set to 0x09 then writing 0xFF changes
the register to 0x08, and writing 0xFF a second time changes
the register to 0x00.
Name:
FIQSTAN
Address:
0xFFFF013C
Name:
FIQVEC
Default value:
0x00000000
Address:
0xFFFF011C
Access:
Read and write
Default value:
0x00000000
Table 118. FIQSTAN MMR Bit Designations
Access:
Read only
Bit
31:8
Name
Reserved
Table 117. FIQVEC MMR Bit Designations
Bit
31:23
22:7
Type
Read only
Read and
write
6:2
1:0
Initial
Value
0
0
0
Reserved
0
7:0
Description
Always read as 0.
IRQBASE register value.
Description
These bits are reserved and should not be
written to.
Setting this bit to 1 enables nesting of FIQ
interrupts. Clearing this bit means no nesting
or prioritization of FIQs is allowed.
EXTERNAL INTERRUPTS (IRQ0 TO IRQ3)
Highest priority source. This is a
value between 0 and 27
representing the possible
interrupt sources. For example, if
the highest currently active FIQ is
Timer2, then these bits are
[00100].
Reserved bits.
The ADuC7121 provides up to six external interrupt sources.
These external interrupts can be individually configured as level
or rising/falling edge triggered.
To enable the external interrupt source, first, the appropriate bit
must be set in the FIQEN or IRQEN register. To select the
required edge or level to trigger on, the IRQCONE register
must be appropriately configured.
To properly clear an edge based external IRQ interrupt, set the
appropriate bit in the IRQCLRE register.
FIQSTAN Register
If IRQCONN.1 is asserted and FIQVEC is read, then one of
these bits assert. The bit that asserts depends on the priority of
the FIQ. If the FIQ is of Priority 0, then Bit 0 asserts; if Priority 1,
then Bit 1 asserts, and so forth.
Name:
IRQCONE
Address:
0xFFFF0034
When a bit is set in this register, all interrupts of that priority
and lower are blocked.
Default value:
0x00000000
Access:
Read and write
To clear a bit in this register, all bits of a higher priority must be
cleared first. It is only possible to clear one bit at a time. For
IRQCONE Register
Table 119. IRQCONEMMR Bit Designations
Bit
31:12
11:10
9:8
7:6
Value
11
10
01
00
11
10
01
00
11
10
01
00
Name
Reserved
IRQ5SRC[1:0]
IRQ4SRC[1:0]
IRQ3SRC[1:0]
Description
These bits are reserved and should not be written to.
External IRQ5 triggers on falling edge.
External IRQ5 triggers on rising edge.
External IRQ5 triggers on low level.
External IRQ5 triggers on high level.
External IRQ4 triggers on falling edge.
External IRQ4 triggers on rising edge.
External IRQ4 triggers on low level.
External IRQ4 triggers on high level.
External IRQ3 triggers on falling edge.
External IRQ3 triggers on rising edge.
External IRQ3 triggers on low level.
External IRQ3 triggers on high level.
Rev. 0 | Page 85 of 96
ADuC7121
Bit
5:4
3:2
1:0
Value
11
10
01
00
11
10
01
00
11
10
01
00
Name
IRQ2SRC[1:0]
IRQ1SRC[1:0]
IRQ0SRC[1:0]
Description
External IRQ2 triggers on falling edge.
External IRQ2 triggers on rising edge.
External IRQ2 triggers on low level.
External IRQ2 triggers on high level.
External IRQ1 triggers on falling edge.
External IRQ1 triggers on rising edge.
External IRQ1 triggers on low level.
External IRQ1 triggers on high level.
External IRQ0 triggers on falling edge.
External IRQ0 triggers on rising edge.
External IRQ0 triggers on low level.
External IRQ0 triggers on high level.
IRQCLRE Register
Table 120. IRQCLRE MMR Bit Designations
Name:
IRQCLRE
Bit
31:25
Name
Reserved
Address:
0xFFFF0038
Default value:
0x00000000
24
IRQ5CLRI
Access:
Read and write
24
IRQ4CLRI
23
22
Reserved
IRQ3CLRI
21
IRQ2CLRI
20
IRQ1CLRI
19
IRQ0CLRI
18:0
Reserved
Rev. 0 | Page 86 of 96
Description
These bits are reserved and should not be
written to.
A 1 must be written to this bit in the IRQ5
interrupt service routine to clear an edge
triggered IRQ5 interrupt.
A 1 must be written to this bit in the IRQ4
interrupt service routine to clear an edge
triggered IRQ4 interrupt.
This bit is reserved.
A 1 must be written to this bit in the IRQ3
interrupt service routine to clear an edge
triggered IRQ3 interrupt.
A 1 must be written to this bit in the IRQ2
interrupt service routine to clear an edge
triggered IRQ2 interrupt.
A 1 must be written to this bit in the IRQ1
interrupt service routine to clear an edge
triggered IRQ1 interrupt.
A 1 must be written to this bit in the IRQO
interrupt service routine to clear an edge
triggered IRQ0 interrupt.
These bits are reserved and should not be
written to.
ADuC7121
TIMERS
The ADuC7121 has five general purpose timers/counters.
•
•
•
•
•
In 48-bit mode, Timer0 counts up from zero. The current
counter value can be read from T0VAL0 and T0VAL1.
Timer0
Timer1
Timer2 or wake-up timer
Timer3 or watchdog timer
Timer4
The five timers in their normal mode of operation can be either
free-running or periodic.
In free-running mode, the counter decrements/increments
from the maximum/minimum value until zero scale/full scale
and starts again at the maximum/minimum value.
In periodic mode, the counter decrements/increments from the
value in the load register (TxLD MMR) until zero scale/full
scale and starts again at the value stored in the load register.
The value of a counter can be read at any time by accessing its
value register (TxVAL). Timers are started by writing in the
control register of the corresponding timer (TxCON).
In normal mode, an IRQ is generated each time the value of the
counter reaches zero if counting down or full scale if counting
up. An IRQ can be cleared by writing any value to the clear
register of the particular timer (TxCLRI).
In 16-bit mode, Timer0 can count up or count down. A 16-bit
value can be written to T0LD that is loaded into the counter. The
current counter value can be read from T0VAL0. Timer0 has a
capture register (T0CAP) that can be triggered by a selected IRQ’s
source initial assertion. When triggered, the current timer value is
copied to T0CAP, and the timer keeps running. This feature can be
used to determine the assertion of an event with more accuracy
than by servicing an interrupt alone.
Timer0 reloads the value from T0LD either when TIMER0
overflows or immediately when T0ICLR is written.
Timer0 interface consists of six MMRs as listed in Table 122.
Table 122. Timer0 Interface MMRs
Name
T0LD
T0CAP
T0VAL0/T0VAL1
Table 121. Event Selection (ES) Numbers
ES
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
Interrupt No.
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Name
RTOS timer (Timer0)
GP Timer0 (Timer1)
Wake-up timer (Timer2)
Watchdog timer (Timer3)
GP Timer4 (Timer4)
IDAC Fault IRQ
Power supply monitor
Undefined
Flash Block 0
Flash Block 1
ADC
UART
SPI
I2C0 master
I2C0 slave
I2C1 master
I2C1 slave
External IRQ0
T0ICLR
T0CON
Description
16-bit register that holds the 16-bit value
loaded into the counter. Available only in
16-bit mode.
16-bit register that holds the 16-bit value
captured by an enabled IRQ event. Available
only in 16-bit mode.
TOVAL0 is a 16-bit register that holds the 16
least significant bits (LSBs).
T0VAL1 is a 32-bit register that holds the 32
most significant bits (MSBs).
T0VAL0 and T0VAL1 are read only. In 16-bit
mode, 16-bit T0VAL0 is used. In 48-bit mode,
both 16-bit T0VAL0 and 32-bit T0VAL1 are used.
8-bit register. Writing any value to this register
clears the interrupt. Available only in 16-bit
mode.
Configuration MMR.
Timer0 Value Registers
T0VAL0 and T0VAL1 are 16-bit and 32-bit registers that hold
the 16 least significant bits and 32 most significant bits, respectively.
T0VAL0 and T0VAL1 are read-only registers. In 16-bit mode,
16-bit T0VAL0 is used. In 48-bit mode, both 16-bit T0VAL0
and 32-bit T0VAL1 are used.
Name:
T0VAL0
Address:
0xFFFF0304
Default value:
0x0000
TIMER0—LIFETIME TIMER
Access:
Read only
Timer0 is a general-purpose, 48-bit count up, or a 16-bit count
up/down timer with a programmable prescaler. Timer0 is
clocked from the core clock, with a prescaler of 1, 16, 256, or
32,768. This gives a minimum resolution of 22 ns when the core
is operating at 41.78 MHz and with a prescaler of one. Timer0
can also be clocked from the undivided core clock, internal
32 kHz oscillator or external 32 kHz crystal.
Name:
T0VAL1
Address:
0xFFFF0308
Default value:
0x00000000
Access:
Read only
Rev. 0 | Page 87 of 96
ADuC7121
Timer0 Capture Register
This is a 16-bit register that holds the 16-bit value captured by
an enabled IRQ event; available in 16-bit mode only.
Name:
T0CAP
Address:
0xFFFF0314
Default value:
0x0000
Access:
Read only
Address:
0xFFFF030C
Default value:
0x00000000
Access:
Read and write
0000
0100
1000
1111
Description
Prescaler.
Source clock divide-by-1 (default).
Source clock divide-by-16.
Source clock divide-by-256.
Source clock divide-by-32,768.
T0LD is a 16-bit register that holds the 16-bit value that is
loaded into the counter; available only in 16-bit mode.
This 17-bit MMR configures the mode of operation of Timer0.
T0CON
Value
Timer0 Load Registers
Timer0 Control Register
Name:
Bit
3:0
Name:
T0LD
Address:
0xFFFF0300
Default value:
0x00
Access:
Read and write
Timer0 Clear Register
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload) Timer0.
Table 123. T0CON MMR Bit Designations
Bit
31:18
17
Value
16:12
11
10:9
00
01
10
11
8
7
6
5
4
0
1
Description
Reserved.
Event select bit.
Set by the user to enable time capture of an
event.
Cleared by the user to disable time capture of
an event.
Event select range, 0 to 16. The events are
described in the introduction to the Timers
section.
Reserved.
Clock select.
Internal 32 kHz oscillator.
UCLK.
External 32 kHz crystal.
HCLK.
Count up. Available in 16-bit mode only.
Set by the user for Timer0 to count up.
Cleared by the user for Timer0 to count down
(default).
Timer0 enable bit.
Set by the user to enable Timer0.
Cleared by the user to disable Timer0
(default).
Timer0 mode.
Set by the user to operate in periodic mode.
Cleared by the user to operate in free-running
mode (default).
Reserved.
Timer0 mode of operation.
16-bit operation (default).
48-bit operation.
Name:
T0CLRI
Address:
0xFFFF0310
Default value:
0x00
Access:
Write only
TIMER1—GENERAL-PURPOSE TIMER
Timer1 is a 32-bit general-purpose timer, count down or count
up, with a programmable prescaler. The prescaler source can be
from the 32 kHz internal oscillator, the 32 kHz external crystal,
the core clock, or from the undivided PLL clock output. This
source can be scaled by a factor of 1, 16, 256, or 32,768. This gives
a minimum resolution of 22 ns when operating at CD zero, the
core is operating at 41.78 MHz, and with a prescaler of one.
The counter can be formatted as a standard 32-bit value or as
hours:minutes:seconds:hundreths.
Timer1 has a capture register (T1CAP) that can be triggered by
a source initial assertion of a selected IRQ. When triggered, the
current timer value is copied to T1CAP, and the timer keeps
running. This feature can be used to determine the assertion of
an event with increased accuracy. Timer1 interface consists of
five MMRs as shown in Table 124.
If the part is in a low power mode and Timer1 is clocked from
the GPIO or low power oscillator source, then Timer1
continues to operate.
Timer1 reloads the value from T1LD either when Timer1
overflows or immediately when T1ICLR is written.
Rev. 0 | Page 88 of 96
ADuC7121
Table 124. Timer1 Interface Registers
Timer1 Control Register
Register
T1LD
This 32-bit MMR configures the mode of operation of Timer1.
T1VAL
T1CAP
T1CLRI
T1CON
Description
32-bit register. Holds 32-bit unsigned integers. This
register is read only.
32-bit register. Holds 32-bit unsigned integers.
32-bit register; Holds 32-bit unsigned integers. This
register is read only.
8-bit register. Writing any value to this register clears
the Timer1 interrupt.
Configuration MMR.
Address:
0xFFFF0320
Default value:
0x00000000
Access:
Read and write
Address:
0xFFFF0328
Default value:
0x00000000
Access:
Read and write
Bit
31:24
23
22:20
19
18
17
T1LD is a 32-bit register that holds the 32-bit value that is
loaded into the counter.
T1LD
T1CON
Table 125. T1CON MMR Bit Designations
Timer1 Load Registers
Name:
Name:
Timer1 Clear Register
Value
16:12
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload) Timer1.
11:9
Name:
T1CLRI
Address:
0xFFFF032C
Default value:
0x00
Access:
Write only
000
001
010
011
8
Timer1 Value Register
T1VAL is a 32-bit register that holds the current value of
Timer1.
Name:
T1VAL
Address:
0xFFFF0324
Default value:
0x00000000
Access:
Read only
7
6
5:4
00
01
10
11
Timer1 Capture Register
This is a 32-bit register that holds the 32-bit value captured by
an enabled IRQ event.
Name:
T1CAP
Address:
0xFFFF0330
Default value:
0x0000
Access:
Read only
3:0
0000
0100
1000
1111
Rev. 0 | Page 89 of 96
Description
8-bit postscaler.
Enable write to postscaler.
Reserved.
Postscaler compare flag.
T1 interrupt generation selection flag.
Event select bit.
Set by the user to enable time capture of an event.
Cleared by the user to disable time capture of
an event.
Event select range, 0 to 16. The events are as
described in the introduction to the Timers
section.
Clock select.
Internal 32 kHz oscillator (default).
Core clock.
UCLK.
P0.6. of the P0.6/MRST/PLAI[2] pin.
Count up.
Set by the user for Timer1 to count up.
Cleared by the user for Timer1 to count down
(default).
Timer1 enable bit.
Set by the user to enable Timer1.
Cleared by the user to disable Timer1 (default).
Timer1 mode.
Set by the user to operate in periodic mode.
Cleared by the user to operate in free-running
mode (default).
Format.
Binary (default).
Reserved.
Hr:Min:Sec:Hundredths: 23 hours to 0 hour.
Hr:Min:Sec:Hundredths: 255 hours to 0 hour.
Prescaler.
Source clock divide-by-1 (default).
Source clock divide-by-16.
Source clock divide-by-256.
Source clock divide-by-32,768.
ADuC7121
TIMER2—WAKE-UP TIMER
Timer2 Value Register
Timer2 is a 32-bit wake-up timer, count down or count up, with
a programmable prescaler. The prescaler is clocked directly from
one of four clock sources, namely, the core clock (default selection),
the internal 32.768 kHz oscillator, the external 32.768 kHz
watch crystal, or the PLL undivided clock. The selected clock
source can be scaled by a factor of 1, 16, 256, or 32,768. The
wake-up timer continues to run when the core clock is disabled.
This gives a minimum resolution of 22 ns when the core is
operating at 41.78 MHz and with a prescaler of 1. Capture of
the current timer value is enabled if the Timer2 interrupt is
enabled via IRQEN[4].
T2VAL is a 32-bit register that holds the current value of Timer2.
The counter can be formatted as a plain 32-bit value or as
Hours:Minutes:Seconds:Hundreths.
Name:
T2CON
Address:
0xFFFF0348
Default value:
0x00000000
Access:
Read and write
Timer2 reloads the value from T2LD either when Timer2 overflows or immediately when T2CLRI is written. The Timer2
interface consists of four MMRs, as shown in Table 126.
Name:
T2VAL
Address:
0xFFFF0344
Default value:
0x00000000
Access:
Read only
Timer2 Control Register
This 32-bit MMR configures the mode of operation for Timer2.
Table 126. Timer2 Interface Registers
Register
T2LD
T2VAL
T2CLRI
T2CON
Description
32-bit register. Holds 32-bit unsigned integers.
32-bit register. Holds 32-bit unsigned integers.
This register is read only.
8-bit register. Writing any value to this register clears
the Timer2 interrupt.
Configuration MMR.
Table 127. T2CON MMR Bit Designations
Bit
31:11
10:9
00
01
10
11
Timer2 Load Registers
T2LD is a 32-bit register, which holds the 32 bit value that is
loaded into the counter.
Name:
T2LD
Address:
0xFFFF0340
Default value:
0x00000000
Access:
Read and write
Value
8
7
6
Timer2 Clear Register
This 8-bit write-only MMR is written (with any value) by the
user code to refresh (reload) Timer2.
Name:
T2CLRI
Address:
0xFFFF034C
Default value:
0x00
Access:
Write only
5:4
00
01
10
11
3:0
0000
0100
1000
1111
Rev. 0 | Page 90 of 96
Description
Reserved.
Clock source select.
Internal 32.768 kHz oscillator (default).
Core clock.
External 32.768kHz watch crystal.
UCLK.
Count up.
Set by the user for Timer2 to count up.
Cleared by the user for Timer2 to count down
(default).
Timer2 enable bit.
Set by the user to enable Timer2.
Cleared by the user to disable Timer2 (default).
Timer2 mode.
Set by the user to operate in periodic mode.
Cleared by the user to operate in free-running
mode (default).
Format.
Binary (default).
Reserved.
Hr:Min:Sec:Hundredths: 23 hours to 0 hour.
Hr:Min:Sec:Hundredths: 255 hours to 0 hour.
Prescaler.
Source clock divide-by-1 (default).
Source clock divide-by-16.
Source clock divide-by-256. (Use this setting in
conjunction with Timer2 Format 1,0 and
Format 1,1.)
Source clock divide-by-32,768.
ADuC7121
Timer3 Interface
TIMER3—WATCHDOG TIMER
Timer3 interface consists of four MMRS as shown in Table 128.
16-BIT LOAD
Table 128. Timer3 Interface Registers
PRESCALER
1, 16, OR 256
16-BIT
UP/DOWN
COUNTER
Register
T3CON
T3LD
TIMER3IRQ
09492-038
LOW POWER
32.768kHz
WATCHDOG
RESET
TIMER3 VALUE
T3VAL
Figure 38. Timer3 Block Diagram
Description
The configuration MMR.
6-bit register (Bit 0 to Bit15); holds 16-bit unsigned
integers.
6-bit register (Bit 0 to Bit 15); holds 16-bit unsigned
integers. This register is read only.
8-bit register. Writing any value to this register clears
the Timer3 interrupt in normal mode or resets a new
timeout period in watchdog mode.
Timer3 has two modes of operation: normal mode and watchdog
mode. The watchdog timer is used to recover from an illegal
software state. When enabled, it requires periodic servicing to
prevent it from forcing a reset of the processor.
T3CLRI
Timer3 reloads the value from T3LD either when Timer3
overflows or immediately when T3CLRI is written.
This 16-bit MMR holds the Timer3 reload value.
Timer3 Load Register
Name:
T3LD
Address:
0xFFFF0360
Default value:
0x3BF8
Access:
Read and write
Normal Mode
The Timer3 in normal mode is identical to Timer0 in 16-bit
mode of operation, except for the clock source. The clock source
is the 32.768 kHz oscillator and can be scaled by a factor of 1,
16, or 256. Timer3 also features a capture facility that allows
capture of the current timer value if the Timer2 interrupt is
enabled via IRQEN[5].
Timer3 Value Register
Watchdog Mode
This 16-bit, read-only MMR holds the current Timer3 count value.
Watchdog mode is entered by setting T3CON[5]. Timer3 decrements from the timeout value present in the T3LD register until
0. The maximum timeout is 512 seconds, using the maximum
prescaler divide-by-256 and full scale in T3LD.
Name:
T3VAL
Address:
0xFFFF0364
Default value:
0x3BF8
Access:
Read only
User software should only configure a minimum timeout
period of 30 milliseconds. This is to avoid any conflict with
Flash/EE memory page erase cycles, requiring 20 ms to
complete a single page erase cycle and kernel execution.
Timer3 Clear Register
If T3VAL reaches 0, a reset or an interrupt occurs, depending
on T3CON[1]. To avoid a reset or an interrupt event, any value
must be written to T3ICLR before T3VAL reaches zero. This
reloads the counter with T3LD and begins a new timeout
period.
Once watchdog mode is entered, T3LD and T3CON are write
protected. These two registers cannot be modified until a poweron reset event resets the watchdog timer. After any other reset
event, the watchdog timer continues to count. The watchdog
timer should be configured in the initial lines of user code to
avoid an infinite loop of watchdog resets.
Timer3 is automatically halted during JTAG debug access and
only recommences counting once JTAG has relinquished control
of the ARM7 core. By default, Timer3 continues to count during
power-down. This can be disabled by setting Bit 0 in T3CON. It is
recommended that the default value is used, that is, the watchdog
timer continues to count during power-down.
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload) Timer3 in watchdog mode to prevent a
watchdog timer reset event.
Name:
T3CLRI
Address:
0xFFFF036C
Default value:
0x0000
Access:
Write only
Timer3 Control Register
The 16-bit MMR configures the mode of operation of Timer3
and is described in detail in Table 129.
Name:
T3CON
Address:
0xFFFF0368
Default value:
0x00
Access:
Read and write one time only
Rev. 0 | Page 91 of 96
ADuC7121
Table 129. T3CON MMR Bit Designations
Secure Clear Bit (Watchdog Mode Only)
Bit
16:9
The secure clear bit is provided for a higher level of protection.
When set, a specific sequential value must be written to T3CLRI
to avoid a watchdog reset. The value is a sequence generated by
the 8-bit linear feedback shift register (LFSR) polynomial = X8 +
X6 + X5 + X + 1.
8
7
6
5
4
3:2
00
01
10
11
1
0
Description
These bits are reserved and should be written as
0s by user code.
Count up/down enable.
Set by user code to configure Timer3 to count up.
Cleared by user code to configure Timer3 to
count down.
Timer3 enable.
Set by user code to enable Timer3.
Cleared by user code to disable Timer3.
Timer3 operating mode.
Set by user code to configure Timer3 to operate
in periodic mode.
Cleared by user to configure Timer3 to operate in
free-running mode.
Watchdog timer mode enable.
Set by user code to enable watchdog mode.
Cleared by user code to disable watchdog mode.
Secure clear bit.
Set by the user to use the secure clear option.
Cleared by the user to disable the secure clear
option by default.
Timer3 Clock(32.768 kHz) prescaler.
Source clock divide-by-1 (default).
Reserved.
Reserved.
Reserved.
Watchdog timer IRQ enable.
Set by user code to produce an IRQ instead of a
reset when the watchdog reaches 0.
Cleared by user code to disable the IRQ option.
PD_OFF.
Set by user code to stop Timer3 when the
peripherals are powered down via Bit 4 in the
POWCON MMR.
Cleared by user code to enable Timer3 when the
peripherals are powered down via Bit 4 in the
POWCON MMR.
Q
D
7
Q
D
6
Q
D
5
The initial value or seed is written to T3CLRI before entering
watchdog mode. After entering watchdog mode, a write to
T3CLRI must match this expected value. If it matches, the LFSR
is advanced to the next state when the counter reload happens.
If it fails to match the expected state, reset is immediately
generated, even if the count has not yet expired.
Because of the properties of the polynomial, do not use the
value, 0x00, as an initial seed. Value 0x00 is always guaranteed
to force an immediate reset. The value of the LFSR cannot be
read; it must be tracked/generated in software.
Example of a sequence:
1.
Enter initial seed, 0xAA, in T3CLRI before starting Timer3
in watchdog mode.
Enter 0xAA in T3CLRI; Timer3 is reloaded.
Enter 0x37 in T3CLRI; Timer3 is reloaded.
Enter 0x6E in T3CLRI; Timer3 is reloaded.
Enter 0x66. 0xDC was expected; the watchdog resets
the chip.
2.
3.
4.
5.
Q
D
4
Q
D
3
Q
D
2
Q
D
1
Q
D
0
09492-039
Value
CLOCK
Figure 39. 8-Bit LFSR
Rev. 0 | Page 92 of 96
ADuC7121
TIMER4—GENERAL-PURPOSE TIMER
Timer4 Clear Register
Timer4 is a 32-bit general-purpose timer, count down or count
up, with a programmable prescaler. The prescaler source can be
the 32 kHz oscillator, the core clock, or PLL undivided output. This
source can be scaled by a factor of 1, 16, 256, or 32,768. This
gives a minimum resolution of 42 ns when operating at CD
zero, the core is operating at 41.78 MHz, and with a prescaler of 1
(ignoring external GPIO).
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload) Timer4.
Name:
T4CLRI
Address:
0xFFFF038C
Default value:
0x00
The counter can be formatted as a standard 32-bit value or as
hours:minutes:seconds:hundreths.
Access:
Write only
Timer4 has a capture register (T4CAP), which can be triggered
by a selected IRQ’s source initial assertion. Once triggered, the
current timer value is copied to T4CAP, and the timer keeps
running. This feature can be used to determine the assertion of
an event with increased accuracy.
Timer4Value Register
Name:
T4VAL
Timer4 interface consists of five MMRS.
Address:
0xFFFF0384
Default value:
0x00000000
Access:
Read only
•
T4LD, T4VAL and T4CAP are 32-bit registers and hold 32bit unsigned integers. T4VAL and T4CAP are read only.
•
T4ICLR is an 8-bit register. Writing any value to this
register clears the Timer1 interrupt.
•
T4CON is the configuration MMR.
•
Note that if the part is in a low power mode, and Timer4 is
clocked from the GPIO or oscillator source then, Timer4
continues to operate.
T4VAL is a 32-bit register that holds the current value of
Timer4.
Timer4 Capture Register
This is a 32-bit register that holds the 32-bit value captured by
an enabled IRQ event.
Name:
T4CAP
Timer4 reloads the value from T4LD either when Timer4
overflows, or immediately when T4ICLR is written.
Address:
0xFFFF0390
Timer4 Load Registers
Default value:
0x00000000
T4LD is a 32-bit register, which holds the 32-bit value that is
loaded into the counter.
Access:
Read only
Name:
T4LD
Address:
0xFFFF0380
Default value:
0x00000000
Access:
Read and write
Timer4 Control Register
This 32-bit MMR configures the mode of operation of Timer4.
Name:
T4CON
Address:
0xFFFF0388
Default value:
0x0000
Access:
Read and write
Rev. 0 | Page 93 of 96
ADuC7121
Table 130. T4CON MMR Bit Designations
Bit
31:18
17
Value
16:12
11:9
000
001
010
011
8
7
6
5:4
00
01
10
11
3:0
0000
0100
1000
1111
Description
Reserved. Set by the user to 0.
Event select bit.
Set by the user to enable time capture of an event.
Cleared by the user to disable time capture of an event.
Event select range, 0 to 31. The events are described in the introduction to the Timers section.
Clock select.
32.768 kHz oscillator.
HCLK (core clock).
UCLK.
UCLK.
Count up.
Set by the user for Timer4 to count up.
Cleared by the user for Timer4 to count down (default).
Timer4 enable bit.
Set by the user to enable Timer4.
Cleared by the user to disable Timer4 (default).
Timer4 mode.
Set by the user to operate in periodic mode.
Cleared by the user to operate in free-running mode (default).
Format.
Binary (default).
Reserved.
Hr:Min:Sec:Hundredths: 23 hours to 0 hour.
Hr:Min:Sec:Hundredths: 255 hours to 0 hour.
Prescaler.
Source clock divide-by-1 (default).
Source clock divide-by-16.
Source clock divide-by-256.
Source clock divide-by-32,768.
Rev. 0 | Page 94 of 96
ADuC7121
OUTLINE DIMENSIONS
A1 BALL
CORNER
7.10
7.00 SQ
6.90
12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
BALL A1
PAD CORNER
5.50
BSC SQ
0.50
BSC
BOTTOM VIEW
TOP VIEW
DETAIL A
*1.40 MAX
*1.11 MAX
DETAIL A
0.15 MIN
COPLANARITY
0.08
SEATING
PLANE
*COMPLIANT WITH JEDEC STANDARDS MO-195-BD WITH
EXCEPTION TO PACKAGE HEIGHT AND THICKNESS.
090408-A
0.35
0.30
0.25
BALL DIAMETER
Figure 40. 108-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-108-4)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
ADuC7121BBCZ
ADuC7121BBCZ-RL
EVAL-ADuC7121QSPZ
1
Temperature Range
−10°C to +95°C
−10°C to +95°C
Package Description
108-Ball CSP_BGA
108-Ball CSP_BGA, 13” Tape and Reel
ADuC7121 QuickStart Development System
Z = RoHS Compliant Part.
Rev. 0 | Page 95 of 96
Package Option
BC-108-4
BC-108-4
ADuC7121
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D09492-0-1/11(0)
Rev. 0 | Page 96 of 96