MAXIM MAX4066ACEE

19-0439; Rev 1; 3/96
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
____________________________Features
♦ Pin Compatible with 74HC4066
♦ Guaranteed On-Resistance:
170Ω max (3V supply)
45Ω max (12V supply)
♦ Guaranteed Match Between Channels:
4Ω max (MAX4066)
2Ω max (MAX4066A)
♦ Guaranteed Low Leakage Currents:
1nA at +25°C (MAX4066)
100pA at +25°C (MAX4066A)
♦ Single-Supply Operation from +2.0V to +16V
♦ V+ to GND Signal Handling
♦ TTL/CMOS-Logic Compatible
♦ Low Power Consumption: 0.5µW
♦ Low Crosstalk: -86dB
♦ Low Off Isolation: -58dB
________________________Applications
♦ Low Distortion: 0.03%
♦ Wide Bandwidth: > 100MHz
Battery-Operated Equipment
______________Ordering Information
Audio and Video Signal Routing
Low-Voltage Data-Acquisition Systems
PART
TEMP. RANGE
Sample-and-Hold Circuits
MAX4066CPD
0°C to +70°C
14 Plastic DIP
Communication Circuits
MAX4066CSD
MAX4066CEE
MAX4066C/D
0°C to +70°C
0°C to +70°C
0°C to +70°C
14 Narrow SO
16 QSOP
Dice*
PIN-PACKAGE
Ordering Information continued at end of data sheet.
* Contact factory for dice specifications.
______________________________________________Pin Configurations/Truth Table
TOP VIEW
NO1 1
14 V+
COM1 2
13 IN1
NO2 3
12 IN4
COM2 4
IN2 5
MAX4066
MAX4066A
TRUTH TABLE
ON/OFF CONTROL
INPUT
NO1 1
16 V+
COM1 2
15 IN1
STATE OF
ANALOG SWITCH
N.C. 3
11 NO4
L
OFF
NO2 4
10 COM4
H
ON
COM2 5
14 IN4
MAX4066
MAX4066A
13 NO4
12 COM4
IN3 6
9
COM3
IN2 6
11 N.C.
GND 7
8
NO3
IN3 7
10 COM3
GND 8
9
NO3
DIP/SO
N.C. = NO INTERNAL CONNECTION
QSOP
________________________________________________________________ Maxim Integrated Products
1
For free samples & the latest literature: http://www.maxim-ic.com, or phone 1-800-998-8800
MAX4066/MAX4066A
_______________General Description
The MAX4066/MAX4066A quad, SPST, CMOS analog
switches are designed to provide superior performance
over the industry-standard devices. These new switches feature guaranteed operation from +2.0V to +16V
and are fully specified at 3V, 5V, and 12V. Both parts
offer 45Ω on-resistance and 2Ω channel-to-channel
matching at 12V, plus 4Ω flatness over the specified
signal range.
Each device is controlled by TTL/CMOS input levels
and can be used as a bilateral switch or multiplexer/
demultiplexer.
Low off leakage current (100pA for the MAX4066A) and
low power consumption (0.5µW) make the MAX4066/
MAX4066A ideal for battery-operated equipment. These
parts are also suitable for low-distortion audio applications. Both devices are available in 14-pin DIP and SO
packages, as well as a 16-pin QSOP. ESD protection is
greater than 2000V per Method 3015.7.
MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
ABSOLUTE MAXIMUM RATINGS
(Voltages referenced to GND)
V+ ...........................................................................-0.3V to +17V
VIN_, VCOM_, VNO (Note 1) ...........................-0.3V to (V + +0.3V)
Current (any terminal) .........................................................30mA
Peak Current (any terminal) ..............................................100mA
ESD per Method 3015.7 ..................................................>2000V
Continuous Power Dissipation (TA = +70°C)
Plastic DIP (derate 10.00mW/°C above +70°C) ............800mW
Narrow SO (derate 8.00mW/°C above +70°C) ..............640mW
QSOP (derate 9.52mW/°C above +70°C) ......................762mW
CERDIP (derate 9.09mW/°C above +70°C) ....................727mW
Operating Temperature Ranges
MAX4066C_ _/MAX4066AC_ _ .............................0°C to +70°C
MAX4066E_ _/MAX4066AE_ _...........................-40°C to +85°C
MAX4066MJD/MAX4066AMJD .......................-55°C to +125°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10sec) .............................+300°C
Note 1: Signals on NO_, COM_, or IN_ exceeding V+ or GND are clamped by internal diodes. Limit forward-diode current to
maximum current rating.
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS—Single +12V Supply
(V+ = 12V ±10%, GND = 0V, VINH = 4.0V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
UNITS
ANALOG SWITCH
Analog Signal Range
On-Resistance
On-Resistance Match
Between Channels (Note 4)
On-Resistance Flatness
(Note 5)
NO or NC Off Leakage
Current (Note 6)
COM Off Leakage Current
(Note 6)
COM On Leakage Current
(Note 6)
2
VCOM,
VNO
RON
∆RON
V+ = 12V,
ICOM = 2mA,
VNO = 10V
TA = +25°C
V+ = 12V,
ICOM = 2mA,
VNO = 10V
TA = +25°C
V+ = 12V,
RFLAT(ON) ICOM = 2mA,
VNO = 10V, 5V, 1V
INO(OFF)
V+ = 12V,
VCOM = 0V,
VNO = 10V
V+ = 12V,
ICOM(OFF) VCOM = 0V,
VNO = 10V
ICOM(ON)
0
(Note 3)
V+ = 12V,
VCOM = 10V,
VNO = 10V
TA = TMIN
to TMAX
V+
16
55
M
75
0.5
MAX4066A
0.5
TA = TMIN to TMAX
2
TA = TMIN to TMAX
TA = TMIN
to TMAX
TA = +25°C
TA = TMIN
to TMAX
TA = +25°C
TA = TMIN
to TMAX
4
2
4
-1
1
MAX4066A
-0.1
0.1
-6
6
-100
100
M
MAX4066
-1
1
MAX4066A
-0.1
0.1
-6
6
-100
100
C, E
M
Ω
Ω
6
MAX4066
C, E
Ω
6
TA = +25°C
TA = +25°C
45
C, E
MAX4066
V
MAX4066
-2
2
MAX4066A
-0.2
0.2
C, E
-12
12
M
-200
200
_______________________________________________________________________________________
nA
nA
nA
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
(V+ = 12V ±10%, GND = 0V, VINH = 4.0V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
(Note 2)
MAX
UNITS
LOGIC INPUT
Input Current with Input
Voltage High
IINH
IN = 5.0V, all others = 0.8V
-0.5
0.005
0.5
µA
Input Current with Input
Voltage Low
IINL
IN = 0.8V, all others = 5.0V
-0.5
0.005
0.5
µA
Turn-On Time
tON
VCOM = 10V, Figure 2
Turn-Off Time
tOFF
VCOM = 10V, Figure 2
On-Channel Bandwidth
BW
Signal = 0dbm, Figure 4,
50Ω in and out
TA = +25°C
100
Charge Injection
(Note 3)
VCTE
CL = 1.0nF, VGEN = 0V,
RGEN = 0Ω, Figure 3
TA = +25°C
1
Off Isolation (Note 7)
VISO
RL = 50Ω, CL = 5pF,
f = 1MHz, Figure 4
TA = +25°C
-58
dB
Crosstalk (Note 8)
VCT
RL = 50Ω, CL = 5pF,
f = 1MHz, Figure 5
TA = +25°C
-86
dB
DYNAMIC
NO Capacitance
C(OFF)
25
TA = +25°C
TA = TMIN to TMAX
100
150
TA = +25°C
15
TA = TMIN to TMAX
75
100
ns
ns
MHz
10
pC
f = 1MHz, Figure 6
TA = +25°C
9
pF
COM Off Capacitance
CCOM(OFF) f = 1MHz, Figure 6
TA = +25°C
9
pF
COM On Capacitance
CCOM(ON) f = 1MHz, Figure 6
TA = +25°C
22
pF
SUPPLY
Power-Supply Range
V
Supply Current
I+
Total Harmonic
Distortion
THD
VIN = 0V or V+,
all channels on or off
TA = TMIN to TMAX
TA = TMIN to TMAX
-1
0.001
0.03
1
µA
%
_______________________________________________________________________________________
3
MAX4066/MAX4066A
ELECTRICAL CHARACTERISTICS—Single +12V Supply (continued)
MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
ELECTRICAL CHARACTERISTICS—Single +5V Supply
(V+ = 5V ±10%, V- = 0V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
MIN
CONDITIONS
TYP
(Note 2)
MAX
UNITS
ANALOG SWITCH
Analog Signal Range
On-Resistance
On-Resistance Match
Between Channels (Note 4)
On-Resistance Flatness
(Notes 3, 5)
NO Off Leakage
Current (Note 6)
COM Off Leakage Current
(Note 6)
COM On Leakage Current
(Note 6)
VCOM,
VNO
RON
(Note 3)
V+ = 4.5V,
ICOM = -1.0mA,
VNO = 3.5V
0
TA = +25°C
TA = TMIN
to TMAX
V+ = 5V,
ICOM = -1.0mA,
VNO = 3V
TA = +25°C
V+ = 5V,
RFLAT(ON) ICOM = -1.0mA,
VNO = 1V, 3V
TA = +25°C
∆RON
INO(OFF)
V+ = 5.5V,
VCOM = 0V,
VNO = 4.5V
V+ = 5.5V,
ICOM(OFF) VCOM = 0V,
VNO = 4.5V
ICOM(ON)
V+ = 5.5V,
VCOM = 5V,
VNO = 4.5V
C, E
V+
45
75
52
100
M
0.3
TA = +25°C
TA = TMIN
to TMAX
TA = +25°C
TA = TMIN
to TMAX
4
4
6
-1
1
MAX4066A
-0.1
0.1
-6
6
-100
100
M
MAX4066
-1
1
MAX4066A
-0.1
0.1
-6
6
-100
100
C, E
M
Ω
8
MAX4066
C, E
Ω
12
TA = TMIN to TMAX
TA = TMIN
to TMAX
Ω
125
TA = TMIN to TMAX
TA = +25°C
V
MAX4066
-2
2
MAX4066A
-0.2
0.2
C, E
-12
12
M
-200
200
nA
nA
nA
DYNAMIC
TA = +25°C
Turn-On Time
tON
VNO = 3V
Turn-Off Time
tOFF
VNO = 3V
On-Channel
Bandwidth
BW
Signal = 0dBm,
50Ω in and out, Figure 4
Q
VGEN = 0V, RGEN = 0V,
CL = 1.0nF, Figure 3
I+
V+ = 5.5V, VIN = 0V or V+, all channels on or off
Charge Injection
(Note 3)
43
TA = TMIN to TMAX
125
175
TA = +25°C
18
TA = TMIN to TMAX
75
125
100
TA = +25°C
2
ns
ns
MHz
10
pC
1
µA
SUPPLY
Positive Supply Current
4
-1
_______________________________________________________________________________________
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
MAX4066/MAX4066A
ELECTRICAL CHARACTERISTICS—Single +3V Supply
(V+ = 2.7V to 3.3V ±10%, GND = 0V, VINH = 2.4V, VINL = 0.8V, TA = TMIN to TMAX, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
(Note 2)
MAX
UNITS
ANALOG SWITCH
Analog Signal Range
VCOM,
VNO
(Note 3)
0
V+
V+ = 3V,
ICOM = -1.0mA,
VNO = 1.5V
TA = +25°C
170
RON
TA = TMIN to TMAX
225
Turn-On Time (Note 3)
tON
V+ = 3V,
VNO or VNC = 1.5V
TA = +25°C
Turn-Off Time (Note 3)
tOFF
V+ = 3V,
VNO or VNC = 1.5V
TA = +25°C
Channel On-Resistance
V
Ω
DYNAMIC
Charge Injection (Note 3)
80
TA = TMIN to TMAX
28
TA = TMIN to TMAX
Q
CL = 1.0nF,
VGEN = 0V, RGEN = 0V
I+
V+ = 3.6V, VIN = 0V or V+, all channels on or off
185
230
150
200
TA = +25°C
ns
ns
2
10
pC
0.001
1
µA
SUPPLY
Positive Supply Current
-1
Note 2: The algebraic convention, where the most negative value is a minimum and the most positive value a maximum, is used in
this data sheet.
Note 3: Guaranteed by design.
Note 4: ∆RON = RON (max) - RON (min).
Note 5: Flatness is defined as the difference between the maximum and minimum value of on-resistance as measured over the
specified analog signal range.
Note 6: Leakage parameters are 100% tested at maximum-rated hot temperature and guaranteed by correlation at +25°C.
Note 7: Off Isolation = 20log10 (VCOM / VNO), VCOM = output, VNO = input to off switch.
Note 8: Between any two switches.
_______________________________________________________________________________________
5
__________________________________________Typical Operating Characteristics
(TA = +25°C, unless otherwise noted.)
ON-RESISTANCE vs. VCOM AND
TEMPERATURE
A
80
C
40
V- = 0V
B
60
A
MAX4066-03
10
V+ = 5.5V
VCOM = 0V
VNO = 4.5V
1
0.1
0.01
C
10
E
0
0.001
0
4
6
8
10
12
14
16
0
2
4
6
8
10
12
VCOM (V)
VCOM (V)
ON LEAKAGE CURRENT
vs. TEMPERATURE
CHARGE INJECTION
vs. VCOM
10
4
1
A
A: V+ = 12V
B: V+ = 5V
C: V+ = 3V
0.0001
-75 -50 -25
16
25 50 75
0
TEMPERATURE (°C)
100
V+ = 5.5V
10
1
VCTE (pC)
2
0.1
B
0
C
0.1
0.01
-2
0.01
0.001
-4
0.001
0.0001
-75 -50 -25
-6
25
0
50 75
TEMPERATURE (°C)
100 125
0
2
4
6
8
10
12
LOSS (dB)
ON
PHASE
0
-20
-40
-60
10
1
-40
-60
FREQUENCY (MHz)
10
0.1
V+ = 5V
INPUT = 0dBm
50Ω IN AND OUT
1
V+ = 12V
5Vp-p SIGNAL
600Ω IN AND OUT
40
20
-20
-30
25 50 75
0
TEMPERATURE (°C)
-25
100
THD (%)
OFF ISOLATION
60
PHASE (degrees)
MAX4066-07
ON RESPONSE
-50
0.0001
-75 -50
TOTAL HARMONIC
DISTORTION vs. FREQUENCY
FREQUENCY RESPONSE
-10
I+
VCOM (V)
0
100
100 125
SUPPLY CURRENT
vs. TEMPERATURE
6
MAX4066-04
100
14
MAX4066-08
2
MAX4066-05
0
MAX4066-06
D
20
6
MAX4066-02
30
20
40
V+ = 5V
B
100
I+ (µA)
RON (Ω)
100
A: TA = -55°C
B: TA = +25°C
C: TA = +85°C
D: TA = +125°C
D
50
RON (Ω)
120
60
MAX4066-01
A: V+ = 2.5V
B: V+ = 3.0V
C: V+ = 5V
D: V+ = 10V
E: V+ = 15V
OFF LEAKAGE CURRENT
vs. TEMPERATURE
OFF LEAKAGE (nA)
ON-RESISTANCE vs. VCOM
150
140
ON LEAKAGE (nA)
MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
300
0.01
10
100
1k
10k 20k
FREQUENCY (Hz)
_______________________________________________________________________________________
100 125
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
PIN
NAME
DIP/SO
QSOP
1, 3, 8, 11
1, 4, 9, 13
NO1–NO4
2, 4, 9, 10
2, 5, 10, 12
COM1–COM4
—
3, 11
N.C.
13, 5, 6, 12
15, 6, 7, 14
IN1–IN4
7
8
GND
14
16
V+
FUNCTION
Analog Switch Normally Open Terminal (bidirectional)
Analog Switch Common Terminal (bidirectional)
Not internally connected
Logic Control Inputs
Ground
Positive Supply Voltage
__________Applications Information
Overvoltage Protection
Proper power-supply sequencing is recommended for
all CMOS devices. Do not exceed the absolute maximum ratings, because stresses beyond the listed ratings may cause permanent damage to the devices.
Always sequence V+ on first, followed by the logic
inputs. If power-supply sequencing is not possible, add
two small signal diodes in series with supply pins for
overvoltage protection (Figure 1). Adding diodes
reduces the analog signal range to 1V below V+ and
1V above GND, but low switch resistance and low leakage characteristics are unaffected. Device operation is
unchanged, and the difference between V+ and GND
should not exceed 17V.
POSITIVE SUPPLY
MAX4066
MAX4066A
V+
NO
COM
Vg
Figure 1. Overvoltage Protection Using Two External Blocking
Diodes
_______________________________________________________________________________________
7
MAX4066/MAX4066A
______________________________________________________________Pin Description
MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
______________________________________________Test Circuits/Timing Diagrams
V+
MAX4066
MAX4066A
SWITCH
OUTPUT
V+
SWITCH
INPUT
V COM
NO
COM
VOUT
RL
300Ω
IN
LOGIC
INPUT
50%
0V
CL
35pF
t OFF
GND
LOGIC
INPUT
t R < 20ns
t F < 20ns
VINH
VOUT
SWITCH
OUTPUT
0V
0V
0.9 x V0UT
0.9 x VOUT
t ON
CL INCLUDES FIXTURE AND STRAY CAPACITANCE.
RL
RL + RON
VOUT = VCOM
(
)
Figure 2. Switching Time
MAX4066
MAX4066A
V+
∆VOUT
V+
RGEN
VOUT
NO
COM
VOUT
CL
V GEN
GND
IN
IN
OFF
ON
Q = (∆V OUT )(C L )
VIN
Figure 3. Charge Injection
8
_______________________________________________________________________________________
OFF
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
SIGNAL
GENERATOR 0dBm
MAX4066
MAX4066A
V+
10nF
COM
SIGNAL
GENERATOR 0dBm
V+
IN
COM
ANALYZER
VINL OR
VINH
VINL OR
VINH
NO
MAX4066
MAX4066A
V+
COM1
N01
IN1
IN2
50Ω
VINL OR
VINH
COM2
N02
ANALYZER
GND
V+
10nF
GND
RL
RL
Figure 4. Off Isolation/On-Channel Bandwidth
MAX4066
MAX4066A
V+
10nF
Figure 5. Crosstalk
V+
COM
IN
CAPACITANCE
METER
VINL OR
VINH
NO
f = 1MHz
GND
Figure 6. Channel Off/On Capacitance
_______________________________________________________________________________________
9
MAX4066/MAX4066A
____________________________________________________Test Circuits (continued)
MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
_Ordering Information (continued)
PART
TEMP. RANGE
___________________Chip Topography
PIN-PACKAGE
MAX4066EPD
-40°C to +85°C
14 Plastic DIP
MAX4066ESD
MAX4066MJD
MAX4066ACPD
-40°C to +85°C
-55°C to +125°C
0°C to +70°C
14 Narrow SO
14 CERDIP**
14 Plastic DIP
MAX4066ACSD
0°C to +70°C
14 Narrow SO
MAX4066ACEE
0°C to +70°C
16 QSOP
Dice*
MAX4066AC/D
0°C to +70°C
MAX4066AEPD
-40°C to +85°C
MAX4066AESD
-40°C to +85°C
14 Narrow SO
MAX4066AEEE
-40°C to +85°C
16 QSOP
MAX4066AMJD
-55°C to +125°C
14 CERDIP**
NO1
V+
IN1
IN4
COM1
14 Plastic DIP
NO2
NO4
COM2
COM4
* Contact factory for dice specifications.
** Contact factory for availability.
IN2
COM3
IN3
GND
NO3
0.065"
(1.65mm)
TRANSISTOR COUNT: 69
SUBSTRATE CONNECTED TO V+
10
______________________________________________________________________________________
0.108"
(2.74mm)
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
D
E
DIM
E1
A
A1
A2
A3
B
B1
C
D1
E
E1
e
eA
eB
L
A3
A A2
L A1
0° - 15°
C
e
B1
eA
B
eB
D1
Plastic DIP
PLASTIC
DUAL-IN-LINE
PACKAGE
(0.300 in.)
INCHES
MAX
MIN
0.200
–
–
0.015
0.175
0.125
0.080
0.055
0.022
0.016
0.065
0.045
0.012
0.008
0.080
0.005
0.325
0.300
0.310
0.240
–
0.100
–
0.300
0.400
–
0.150
0.115
PKG. DIM PINS
P
P
P
P
P
N
D
D
D
D
D
D
8
14
16
18
20
24
MILLIMETERS
MIN
MAX
–
5.08
0.38
–
3.18
4.45
1.40
2.03
0.41
0.56
1.14
1.65
0.20
0.30
0.13
2.03
7.62
8.26
6.10
7.87
2.54
–
7.62
–
–
10.16
2.92
3.81
INCHES
MIN
MAX
0.348 0.390
0.735 0.765
0.745 0.765
0.885 0.915
1.015 1.045
1.14 1.265
MILLIMETERS
MIN
MAX
8.84
9.91
18.67 19.43
18.92 19.43
22.48 23.24
25.78 26.54
28.96 32.13
21-0043A
DIM
D
0°-8°
A
0.101mm
0.004in.
e
B
A1
E
C
H
L
Narrow SO
SMALL-OUTLINE
PACKAGE
(0.150 in.)
A
A1
B
C
E
e
H
L
INCHES
MAX
MIN
0.069
0.053
0.010
0.004
0.019
0.014
0.010
0.007
0.157
0.150
0.050
0.244
0.228
0.050
0.016
DIM PINS
D
D
D
8
14
16
MILLIMETERS
MIN
MAX
1.35
1.75
0.10
0.25
0.35
0.49
0.19
0.25
3.80
4.00
1.27
5.80
6.20
0.40
1.27
INCHES
MILLIMETERS
MIN MAX
MIN
MAX
0.189 0.197 4.80
5.00
0.337 0.344 8.55
8.75
0.386 0.394 9.80 10.00
21-0041A
______________________________________________________________________________________
11
MAX4066/MAX4066A
________________________________________________________Package Information
MAX4066/MAX4066A
Low-Cost, Low-Voltage, Quad, SPST,
CMOS Analog Switches
___________________________________________Package Information (continued)
DIM
A
A1
A2
B
C
D
E
e
H
h
L
N
S
α
D
A
e
A1
B
S
E
INCHES
MILLIMETERS
MAX
MIN
MIN
MAX
0.068
0.061
1.55
1.73
0.004 0.0098 0.127
0.25
0.061
0.055
1.40
1.55
0.012
0.008
0.20
0.31
0.0075 0.0098
0.19
0.25
SEE VARIATIONS
0.157
0.150
3.81
3.99
0.25 BSC
0.635 BSC
0.244
0.230
5.84
6.20
0.016
0.010
0.25
0.41
0.035
0.016
0.41
0.89
SEE VARIATIONS
SEE VARIATIONS
8°
0°
0°
8°
H
h x 45°
α
A2
N
E
C
DIM PINS
D
S
D
S
D
S
D
S
16
16
20
20
24
24
28
28
INCHES
MILLIMETERS
MIN
MAX MIN
MAX
0.189 0.196 4.80
4.98
0.0020 0.0070 0.05
0.18
0.337 0.344 8.56
8.74
0.0500 0.0550 1.27
1.40
0.337 0.344 8.56
8.74
0.0250 0.0300 0.64
0.76
0.386 0.393 9.80
9.98
0.0250 0.0300 0.64
0.76
21-0055A
QSOP
QUARTER
SMALL-OUTLINE
PACKAGE
L
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
12 __________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 (408) 737-7600
© 1996 Maxim Integrated Products
Printed USA
is a registered trademark of Maxim Integrated Products.