LT1030 Quad Low Power Line Driver U DESCRIPTION FEATURES ■ ■ ■ ■ ■ ■ ■ ■ Low Operating Voltage ±5V to ±15V Supply Current: 500µA Zero Supply Current When Shut Down Outputs Can Be Driven ± 30V Output “Open” When Off (Three-State) Output Drive: 10mA Pinout Similar to 1488* Output of Several Devices Can Be Paralleled U APPLICATIONS ■ ■ ■ RS232 Driver Micropower Interface Level Translator The LT ® 1030 is an RS232 line driver that operates over a ±5V to ±15V range on low supply current and can be shut down to zero supply current. Outputs are fully protected from externally applied voltages of ±30V by current limiting. Since the output swings to within 200mV of the positive supply and 1V of the negative supply, power supply needs are minimized. A major advantage of the LT1030 is the high impedance output state when off or powered down, which allows several different drivers on the same bus. Our RS232 product line includes other high performance devices. The LT1039 is a triple low power driver/receiver with shutdown that can be powered from a 5V supply. The LT1080 is a 5V powered dual driver/receiver with on-chip ±9V power generator and shutdown. , LTC and LT are registered trademarks of Linear Technology Corporation. *Check compatability (some pins may be different). U TYPICAL APPLICATIONS Output Swing vs Output Current – 6V 1 LT1030 14 2 13 3 12 ON/OFF 4 (0V TO 5V)† 5 INPUT 6 OUTPUT 7 GND 11 INPUT OUTPUT 10 9 8 6V STROBE* INPUT OUTPUT NC INPUT OUTPUT *NO CONNECTION NEEDED WHEN NOT USED † 5V = ON OUTPUT VOLTAGE REFERRED TO SUPPLIES (V) RS232 Line Driver V+ –0.2 OUTPUT HIGH –0.4 1.2 1.0 OUTPUT LOW 0.8 0.6 0.4 0.2 V– 0 1 3 4 2 OUTPUT CURRENT (mA) 5 LT1030 • TA01 LT1030 • TA02 1 LT1030 W U U W W W Supply Voltage ...................................................... ±15V Logic Input Pins ............................................. V – to 25V On/Off Pin .................................................... GND to 12V Output (Forced) .............................. V – + 30V, V + – 30V Short-Circuit Duration (to ±30V) ..................... Indefinite Operating Temperature Range Commercial ............................................. 0°C to 70°C Guaranteed Functional by Design ....... – 25°C to 85°C Storage Temperature ............................ – 65°C to 150°C Lead Temperature (Soldering, 10 sec).................. 300°C U ABSOLUTE MAXIMUM RATINGS PACKAGE/ORDER INFORMATION ORDER PART NUMBER TOP VIEW V– (–15V TO –5V) ON/OFF (0V TO 5V) GND 1 V+ 14 (5V TO 15V) 2 13 STROBE 3 12 4 11 5 10 6 9 7 8 LT1030CN LT1030CS S PACKAGE 14-LEAD PLASTIC SO N PACKAGE 14-LEAD PDIP LT1030CJ CONSULT FACTORY TJMAX = 125°C, θJA = 90°C/ W (N) TJMAX = 125°C, θJA = 95°C/ W (S) Consult factory for Industrial and Military grade parts. ELECTRICAL CHARACTERISTICS (Supply Voltage = ±5 to ±15V) PARAMETER CONDITIONS Supply Current Power Supply Leakage Current VON/OFF ≥ 2.4V, IOUT = 0, All Outputs Low VON/OFF ≤ 0.4V VON/OFF ≤ 0.1V Load = 2mA Positive Negative VSUPPLY ± 5V to ±15V Operating or Shutdown Shutdown VS = 0V, VOUT = ±30V VS = ±15V, VOUT = ± 20V Operating or Shutdown Low Input (VOUT = High) High Input (VOUT = Low) VIN > 2.0V VIN < 0.8V 0 ≤ VIN ≤ 5V Output Voltage Swing Output Current Output Overload Voltage (Forced) Output Current Input Overload Voltage (Forced) Logic Input Levels Logic Input Current On/Off Pin Current Slew Rate The ● denotes specifications which apply over the full operating temperature range. MIN TYP MAX UNITS 1000 10 150 V + – 0.3V 500 1 10 V + – 0.1V V – + 0.9V 12 µA µA µA V V mA V µA µA V V V µA µA µA V/µS ● ● ● 5 V + – 30V 2 2 V– ● ● ● 2 ● –10 4 1.4 1.4 2 10 30 15 V – + 1.4V V – + 30V 100 100 15 0.8 20 20 65 30 Note 1: 3V applied to the Strobe pin will force all outputs low. Strobe pin input impedance is about 2k to ground. Leave open when not used. U U U PIN FUNCTIONS V –(Pin 1): Operates – 15V to – 2V. STROBE (Pin 13): Forces all outputs low. Drive with 3V. LOGIC INPUT (Pins 2, 5, 9, 12): Operate properly on TTL or CMOS levels. Output valid from (V – + 2V) ≤ VIN ≤ 15V. Connect to 5V when not used. V + (Pin 14): Positive supply 5V to 15V. OUTPUT (Pins 3, 6, 8, 11): Line drive outputs. ON/OFF (Pin 4): Shuts down entire circuit. Cannot be left open. For “normally on” operation, connect between 5V to 10V. GND (Pin 7): 2 Ground must be more positive than V –. 14 8 LT1030 1 7 1N4001 LT1030 • PF01 Note: As with other bipolar ICs, forward biasing the substrate diode can cause problems. The LT1030 will draw high current from V + to ground if the V – pin is open circuited or pulled above ground. If this is possible, connecting a diode from V – to ground will prevent the high current state. Any low cost diode can be used. LT1030 U W TYPICAL PERFORMANCE CHARACTERISTICS On Supply Current vs Temperature On Supply Current vs Supply Voltage 5.0 5.0 VSUPPLY = ±12V 4.5 100 3.0 2.5 2.0 1.5 1.0 3.5 SUPPLY CURRENT (µA) SUPPLY CURRENT (mA) 4.0 ALL OUTPUTS HIGH 3.5 ALL OUTPUTS HIGH 3.0 2.5 2.0 1.5 1.0 ALL OUTPUTS LOW 0.5 0 100 125 10 30 2.4 2.0 100 80 60 40 20 75 100 TEMPERATURE (°C) 125 5 10 1.4 MIN ON VOLTAGE 1.2 1.0 0.8 0.6 LT1030 • TPC05 SINKING 25 20 SOURCING 15 10 100 125 LT1332 • TPC06 25 –0.4 23 IOUT = 5mA 21 IOUT = 1mA 1.4 1.2 IOUT = –5mA 1.0 0.8 0.6 IOUT = –1mA SLEW RATE (V/µs) OUTPUT VOLTAGE REFERED TO SUPPLIES (V) 30 Slew Rate vs Temperature V+ –0.2 17 FALLING 15 13 RISING 11 9 0.2 7 100 125 VS = ±12V RL = 3K CL = 51pF VSLEW = ±8V 19 0.4 V– –75 –50 –25 0 25 50 75 TEMPERATURE (°C) 100 125 LT1030 • TPC06 Output Swing vs Temperature Current Limit vs Temperature 35 MAX OFF VOLTAGE (IOUT < 20µA) GND 25 50 75 –75 –50 –25 0 TEMPERATURE (°C) 15 ON/OFF PIN VOLTAGE (V) LT1030 • TPC04 5 25 50 75 –75 –50 –25 0 TEMPERATURE (°C) MAX OFF VOLTAGE (IOUT < 200µA) 1.6 0.2 –20 GND 0.01 50 1.8 0.4 0 25 RL = 3k 2.2 ON/OFF PIN VOLTAGE (V) ON/OFF PIN CURRENT (µA) OUTPUT LEAKAGE CURRENT (µA) OUTPUT FORCED TO 25V 125 Shutdown Voltage vs Temperature 120 OUTPUT FORCED TO –25V 75 100 TEMPERATURE (°C) LT1030 • TPC03 140 10 50 25 On/Off Pin Current vs Voltage VSUPPLY = ±12V 0.1 0.1 LT1030 • TPC02 Off Output Leakage vs Temperature 0 0 0.01 25 20 15 TOTAL SUPPLY VOLTAGE (V) LT1030 • TPC01 100 10 ALL OUTPUTS LOW 0.5 0 –75 –50 –25 0 25 50 75 TEMPERATURE (°C) OUTPUT CURRENT (mA) VSUPPLY = ±12V 4.5 4.0 SUPPLY CURRENT (mA) Off Supply Current vs Temperature 5 –75 –50 –25 0 25 50 75 TEMPERATURE (°C) LT1030 • TPC08 Information furnished by Linear Technology Corporation is believed to be accurate and reliable. However, no responsibility is assumed for its use. Linear Technology Corporation makes no representation that the interconnection of its circuits as described herein will not infringe on existing patent rights. 100 125 LT1030 • TPC09 3 LT1030 U W TYPICAL PERFORMANCE CHARACTERISTICS On-Off Response Time On-Off Response Time VS = ±12V RL = 3k CL = 51pF 10V 5V 0V 0V OUTPUT – 5V (VIN = 5V) – 10V OUTPUT (VIN = 0V) ON/OFF INPUT OUTPUT (VIN = 0V) OUTPUT (VIN = 5V) 5V 0V ON/OFF INPUT H = 100µs/DIV Output Waveforms VS = ±6V RL = 3k CL = 51pF 6V 4V 2V 0V 0V – 2V – 4V – 6V 5V 0V 10V OUTPUT 0V (VS = ±12V) –10V 5V INPUT 0V H = 100µs/DIV Output Waveform Driving Capacitive Load VIN = 5V VS = ±6V RL = 3k CL = 0.01µF 10V 5V OUTPUT 0V – 5V – 10V STROBE INPUT 5V 0V H = 10µs/DIV U PACKAGE DESCRIPTION H = 2µs/DIV Strobe Pin Response Time VS = ±6V RL = 3k CL = 0.01µF 6V 4V 2V 0V OUTPUT – 2V – 4V – 6V 5V INPUT 0V OUTPUT (VS = ±6V) RL = 3k CL = 51pF 5V 0V –5V H = 2µs/DIV Dimension in inches (millimeters) unless otherwise noted. N Package 14-Lead Plastic DIP 0.300 – 0.325 (7.620 – 8.255) 0.009 – 0.015 (0.229 – 0.381) +0.025 0.325 – 0.015 8.255 + 0.635 – 0.381 ( ) 0.130 ± 0.005 (3.302 ± 0.127) 0.045 – 0.065 (1.143 – 1.651) 0.015 (0.380) MIN 0.065 (1.651) TYP 0.125 (3.175) MIN 0.005 (0.125) MIN 0.100 ± 0.010 (2.540 ± 0.254) 0.008 – 0.010 (0.203 – 0.254) 0.018 ± 0.003 (0.457 ± 0.076) 1 2 9 8 5 6 7 3 4 N14 0695 *THESE DIMENSIONS DO NOT INCLUDE MOLD FLASH OR PROTRUSIONS. MOLD FLASH OR PROTRUSIONS SHALL NOT EXCEED 0.010 INCH (0.254mm) 14 13 0.337 – 0.344* (8.560 – 8.738) 12 11 10 9 8 0.228 – 0.244 (5.791 – 6.197) 0.004 – 0.010 (0.101 – 0.254) 0.053 – 0.069 (1.346 – 1.752) 0° – 8° TYP 0.014 – 0.019 0.016 – 0.050 (0.355 – 0.483) 0.406 – 1.270 *DIMENSION DOES NOT INCLUDE MOLD FLASH. MOLD FLASH SHALL NOT EXCEED 0.006" (0.152mm) PER SIDE **DIMENSION DOES NOT INCLUDE INTERLEAD FLASH. INTERLEAD FLASH SHALL NOT EXCEED 0.010" (0.254mm) PER SIDE 13 0.255 ± 0.015* (6.477 ± 0.381) S Package 14-Lead Plastic SO 0.010 – 0.020 × 45° (0.254 – 0.508) 14 0.770* (19.558) MAX 11 12 10 0.050 (1.270) TYP 0.150 – 0.157** (3.810 – 3.988) 1 2 3 4 5 6 7 S14 0695 RELATED PARTS PART NUMBER DESCRIPTION COMMENTS LT1180A Dual 5V RS232 Transceiver with Shutdown Shutdown Plus 10kV ESD LTC ® 1321 Programmable RS232/RS485 Transceiver Low Supply Current, High Speed Data Transmission LT1134A 4-Driver/4-Receiver RS232 Tranceiver Single 5V Supply, 10kV ESD Protection, 0.1µF Charge Pump Capacitor LTC1383 Micropower Dual 5V RS232 Transceiver Lowest Power 2-Driver/2-Receiver Solution 4 Linear Technology Corporation LT/GP 0895 2K • REV B PRINTED IN USA 1630 McCarthy Blvd., Milpitas, CA 95035-7487 (408) 432-1900 ● FAX: (408) 434-0507 ● TELEX: 499-3977 LINEAR TECHNOLOGY CORPORATION 1987