AD AD9552

Oscillator Frequency Upconverter
AD9552
FEATURES
GENERAL DESCRIPTION
Converts a low frequency input reference signal to a high
frequency output signal
Input frequencies from 6.6 MHz to 112.5 MHz
Output frequencies up to 900 MHz
Preset pin programmable frequency translation ratios
Arbitrary frequency translation ratios via SPI port
On-chip VCO
Accepts a crystal resonator and/or an external oscillator
as a reference frequency source
Secondary output (either integer-related to the primary
output or a copy of the reference input)
RMS jitter: <0.5 ps
SPI-compatible, 3-wire programming interface
Single supply (3.3 V)
Very low power: <400 mW (under most conditions)
Small package size (5 mm × 5 mm)
The AD9552 is a fractional-N phase locked loop (PLL) based
clock generator designed specifically to replace high frequency
crystal oscillators and resonators. The device employs a sigmadelta (Σ-Δ) modulator (SDM) to accommodate fractional
frequency synthesis. The user supplies an input reference signal
by connecting a single-ended clock signal directly to the REF
pin or by connecting a crystal resonator across the XTAL pins.
APPLICATIONS
The AD9552 is specified to operate over the extended industrial
temperature range of −40°C to +85°C.
The AD9552 is pin programmable, providing one of 64 standard
output frequencies based on one of eight common input
frequencies. The device also has a 3-wire SPI interface, enabling
the user to program custom input-to-output frequency ratios.
The AD9552 relies on an external capacitor to complete the loop
filter of the PLL. The output is compatible with LVPECL, LVDS,
or single-ended CMOS logic levels, although the AD9552 is
implemented in a strictly CMOS process.
Cost effective replacement of high frequency VCXO, OCXO,
and SAW resonators
Extremely flexible frequency translation with low jitter for
SONET/SDH (including FEC), 10 Gb Ethernet, Fibre
Channel, and DRFI/DOCSIS
High-definition video frequency translation
Wireless infrastructure
Test and measurement (including handheld devices)
BASIC BLOCK DIAGRAM
AD9552
REF
XTAL
INPUT
FREQUENCY
SOURCE
SELECTOR
OUT2
PLL
OUTPUT
CIRCUITRY
OUT1
07806-001
PIN-DEFINED AND SERIAL PROGRAMMING
Figure 1.
Rev. C
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2009–2010 Analog Devices, Inc. All rights reserved.
AD9552
TABLE OF CONTENTS
Features .............................................................................................. 1
Preset Frequency Ratios ............................................................ 13
Applications ....................................................................................... 1
Component Blocks ..................................................................... 15
General Description ......................................................................... 1
Part Initialization and Automatic Power-On Reset ............... 17
Basic Block Diagram ........................................................................ 1
Output/Input Frequency Relationship .................................... 17
Revision History ............................................................................... 2
Calculating Divider Values ....................................................... 17
Specifications..................................................................................... 3
Low Dropout (LDO) Regulators .............................................. 18
Crystal Input Characteristics ...................................................... 4
Applications Information .............................................................. 19
Output Characteristics ................................................................. 4
Thermal Performance ................................................................ 19
Jitter Characteristics ..................................................................... 5
Serial Control Port ......................................................................... 20
Serial Control Port ....................................................................... 6
Serial Control Port Pin Descriptions ....................................... 20
Serial Control Port Timing ......................................................... 6
Operation of the Serial Control Port ....................................... 20
Absolute Maximum Ratings............................................................ 7
Instruction Word (16 Bits) ........................................................ 21
ESD Caution .................................................................................. 7
MSB/LSB First Transfers ........................................................... 21
Pin Configuration and Function Descriptions ............................. 8
Register Map ................................................................................... 23
Typical Performance Characteristics ............................................. 9
Register Map Descriptions ........................................................ 24
Input/Output Termination Recommendations .......................... 12
Outline Dimensions ....................................................................... 30
Theory of Operation ...................................................................... 13
Ordering Guide .......................................................................... 30
REVISION HISTORY
7/10—Rev. B to Rev. C
Changed Crystal Load Capacitance to 15 pF............. Throughout
Added Conditions Statement to Specifications Section, Supply
Voltage Specifications, and Input Voltage Specifications ............ 3
Reformatted Specifications Section (Renumbered Sequentially)..... 3
Added Input/Output Termination Recommendations Section,
Figure 17, and Figure 18 (Renumbered Sequentially) ............... 13
Moved Preset Frequency Ratios Section ..................................... 13
Changes to Component Blocks Section ...................................... 15
Added Part Initialization and Automatic Power-On
Reset Section ................................................................................... 17
4/10—Rev. A to Rev. B
Changes to Preset Frequency Ratios Section .............................. 12
Moved Table 15 and Changes to Table 15 ................................... 13
Changes to Figure 17 ...................................................................... 14
Changes to PLL Section, Output Dividers Section, and
Input-to-OUT2 Option Section ............................................... 15
Changes to Output/Input Frequency Relationship Section ...... 16
Changes to Table 22 ....................................................................... 23
Changes to Table 26 ....................................................................... 26
9/09—Rev. 0 to Rev. A
Changes to Table 4.............................................................................3
Changes to Table 5.............................................................................4
Added Table 6; Renumbered Sequentially .....................................4
Changes to Figure 5 ...........................................................................9
Changes to PLL Section ................................................................. 14
Changes to Table 22 ....................................................................... 21
Changes to Table 25 ....................................................................... 24
7/09—Revision 0: Initial Version
Rev. C | Page 2 of 32
AD9552
SPECIFICATIONS
Minimum (min) and maximum (max) values apply for the full range of supply voltage and operating temperature variations. Typical (typ)
values apply for VDD = 3.3 V; TA = 25°C, unless otherwise noted.
Table 1.
Parameter
SUPPLY VOLTAGE
POWER CONSUMPTION
Total Current
VDD Current By Pin
Pin 7
Pin 18
Pin 21
Pin 28
LVPECL Output Driver
LOGIC INPUT PINS
INPUT CHARACTERISTICS 1
Logic 1 Voltage, VIH
Logic 0 Voltage, VIL
Logic 1 Current, IIH
Logic 0 Current, IIL
LOGIC OUTPUT PINS
Output Characteristics
Output Voltage High, VOH
Output Voltage Low, VOL
RESET PIN
Input Characteristics 2
Input Voltage High, VIH
Input Voltage Low, VIL
Input Current High, IINH
Input Current Low, IINL
Minimum Pulse Width High
REFERENCE CLOCK
INPUT CHARACTERISTICS
Frequency Range
Min
3.135
Typ
3.30
Max
3.465
Unit
V
Test Conditions/Comments
Pin 7, Pin 18, Pin 21, Pin 28
149
169
mA
At maximum output frequency with both output channels active
2
77
35
35
36
3
86
41
41
41
mA
mA
mA
mA
mA
1.0
V
For the CMOS inputs, a static Logic 1 results from either a pull-up
resistor or no connection
0.8
3
17
V
μA
μA
0.4
V
V
2.7
1.8
2
V
V
μA
μA
ns
7.94
6.57
MHz
MHz
0.3
31
1.3
12.5
43
900 MHz with 100 Ω termination between both pins of the output
driver
93.06
71.28
112.5
MHz
MHz
MHz
86.17
MHz
N3 = 255; 2× frequency multiplier enabled; valid for all VCO bands
N 3 = 255; 2× frequency multiplier enabled; fVCO = 3.35 GHz, which constrains the frequency at OUT1 to be an integer sub-multiple of 3.35 GHz
(that is, fOUT1 = 3.35 ÷ M GHz, where M is the product of the P0 and P1
output divider values)
SDM4 disabled; N3 = 365; valid for all VCO bands
SDM4 enabled; N3 = 476; valid for all VCO bands
SDM 4 disabled; N3 = 36 5 ; fVCO = 4.05 GHz, which constrains the
frequency at OUT1 to be an integer sub-multiple of 4.05 GHz (that is,
fOUT1 = 4.05÷M GHz, where M is the product of the P0 and P1 output
divider values)
SDM4 enabled; N3 = 47 6 ; fVCO = 4.05 GHz, which constrains the frequency
at OUT1 to be an integer sub-multiple of 4.05 GHz (that is, fOUT1 =
4.05÷M GHz, where M is the product of the P0 and P1 output divider
values)
Rev. C | Page 3 of 32
AD9552
Parameter
Input Capacitance
Input Resistance
Duty Cycle
Input Voltage
Input High Voltage, VIH
Input Low Voltage, VIL
Input Threshold Voltage
Min
40
Max
60
0.52
Unit
pF
kΩ
%
1.0
V
V
V
4050
3350
45
MHz
MHz
MHz/V
140
ppm
μs
1.62
VCO CHARACTERISTICS
Frequency Range
Upper Bound
Lower Bound
VCO Gain
VCO Tracking Range
VCO Calibration Time
Typ
3
130
±300
Test Conditions/Comments
When ac coupling to the input receiver, the user must dc bias the input
to 1 V
fPFD 7 = 77.76 MHz; time between completion of the VCO calibration
command (the rising edge of CS (Pin 12)) to the rising edge of LOCKED
(Pin 20).
1
The A[2:0], Y[5:0], and OUTSEL pins have 100 kΩ internal pull-up resistors.
The RESET pin has a 100 kΩ internal pull-up resistor, so the default state of the device is reset.
N is the integer part of the feedback divider.
4
Sigma-delta modulator.
5
The minimum allowable feedback divider value with the SDM disabled.
6
The minimum allowable feedback divider value with the SDM enabled.
7
The frequency at the input to the phase-frequency detector.
2
3
CRYSTAL INPUT CHARACTERISTICS
Table 2.
Parameter
CRYSTAL FREQUENCY
Range
Tolerance
CRYSTAL MOTIONAL RESISTANCE
CRYSTAL LOAD CAPACITANCE
Min
Typ
Max
Unit
10
26
52
20
100
MHz
ppm
Ω
pF
15
Test Conditions/Comments
Using a crystal with a specified load capacitance other than
15 pF (8 pF to 24 pF) is possible, but necessitates using the
SPI port to configure the AD9552 crystal input capacitance.
OUTPUT CHARACTERISTICS
Table 3.
Parameter
LVPECL MODE
Differential Output Voltage Swing
Common-Mode Output Voltage
Frequency Range
Duty Cycle
Rise/Fall Time 1 (20% to 80%)
Min
Typ
Max
Unit
Test Conditions/Comments
690
VDD − 1.77
0
40
765
VDD − 1.66
889
VDD − 1.20
900
60
305
mV
V
MHz
%
ps
Output driver static
Output driver static
255
Rev. C | Page 4 of 32
Up to 805 MHz output frequency
100 Ω termination between both pins of
the output driver
AD9552
Parameter
LVDS MODE
Differential Output Voltage Swing
Balanced, VOD
Min
Typ
247
Unbalanced, ΔVOD
Offset Voltage
Common Mode, VOS
Common-Mode Difference, ΔVOS
1.125
Short-Circuit Output Current
Frequency Range
Duty Cycle
Rise/Fall Time1 (20% to 80%)
0
40
17
285
Max
Unit
Test Conditions/Comments
454
mV
25
mV
Voltage swing between output pins;
output driver static
Absolute difference between voltage
swing of normal pin and inverted pin;
output driver static
1.375
25
V
mV
24
900
60
355
mA
MHz
%
ps
CMOS MODE
Output Voltage High, VOH
IOH = 10 mA
IOH = 1 mA
Output Voltage Low, VOL
IOL = 10 mA
IOL = 1 mA
Frequency Range
Duty Cycle
Rise/Fall Time1 (20% to 80%)
1
Output driver static
Voltage difference between output pins;
output driver static
Up to 805 MHz output frequency
100 Ω termination between both pins of
the output driver
Output driver static; standard drive
strength setting
2.8
2.8
V
V
Output driver static; standard drive
strength setting
0
45
500
0.5
0.3
200
V
V
MHz
55
745
%
ps
3.3 V CMOS; standard drive strength
setting
At maximum output frequency
3.3 V CMOS; standard drive strength
setting; 15 pF load
The listed values are for the slower edge (rise or fall).
JITTER CHARACTERISTICS
Table 4.
Parameter
JITTER GENERATION
12 kHz to 20 MHz
50 kHz to 80 MHz
4 MHz to 80 MHz
JITTER TRANSFER BANDWIDTH
JITTER TRANSFER PEAKING
Min
Typ
0.64
0.70
0.47
0.50
0.11
0.12
100
0.3
Max
Unit
ps rms
ps rms
ps rms
ps rms
ps rms
ps rms
kHz
dB
Rev. C | Page 5 of 32
Test Conditions/Comments
Input = 19.44 MHz crystal resonator
fOUT = 622.08 MHz (integer mode)
fOUT = 625 MHz (fractional mode)
fOUT = 622.08 MHz (integer mode)
fOUT = 625 MHz (fractional mode)
fOUT = 622.08 MHz (integer mode)
fOUT = 625 MHz (fractional mode)
See the Typical Performance Characteristics section
See the Typical Performance Characteristics section
AD9552
SERIAL CONTROL PORT
Table 5.
Parameter
CS
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SCLK
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
SDIO
Input
Input Logic 1 Voltage
Input Logic 0 Voltage
Input Logic 1 Current
Input Logic 0 Current
Input Capacitance
Output
Output Logic 1 Voltage
Output Logic 0 Voltage
Min
Typ
Max
1.6
0.5
0.03
2
2
1.6
0.5
2
0.03
2
1.6
0.5
1
1
2
2.8
0.3
Unit
V
V
μA
μA
pF
V
V
μA
μA
pF
V
V
μA
μA
pF
V
V
SERIAL CONTROL PORT TIMING
Table 6.
Parameter
SCLK
Clock Rate, 1/tCLK
Pulse Width High, tHIGH
Pulse Width Low, tLOW
SDIO to SCLK Setup, tDS
SCLK to SDIO Hold, tDH
SCLK to Valid SDIO, tDV
CS to SCLK Setup (tS) and Hold (tH)
CS Minimum Pulse Width High
Limit
Unit
50
3
3
4
0
13
0
6.4
MHz max
ns min
ns min
ns min
ns min
ns max
ns min
ns min
Rev. C | Page 6 of 32
Test Conditions/Comments
1 mA load current
1 mA load current
AD9552
ABSOLUTE MAXIMUM RATINGS
ESD CAUTION
Table 7.
Parameter
Supply Voltage (VDD)
Maximum Digital Input Voltage
Storage Temperature
Operating Temperature Range
Lead Temperature (Soldering, 10 sec)
Junction Temperature
Rating
3.6 V
−0.5 V to VDD + 0.5 V
−65°C to +150°C
−40°C to +85°C
300°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Rev. C | Page 7 of 32
AD9552
32
31
30
29
28
27
26
25
Y3
Y2
Y1
Y0
VDD
OUT1
OUT1
GND
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
1
2
3
4
5
6
7
8
PIN 1
INDICATOR
AD9552
TOP VIEW
(Not to Scale)
24
23
22
21
20
19
18
17
GND
OUT2
OUT2
VDD
LOCKED
LDO
VDD
LDO
NOTES
1. EXPOSED DIE PAD MUST BE
CONNECTED TO GND.
07806-002
XTAL
XTAL
REF
CS
SCLK
SDIO
OUTSEL
FILTER
9
10
11
12
13
14
15
16
Y4
Y5
A0
A1
A2
RESET
VDD
LDO
Figure 2. Pin Configuration
Table 8. Pin Function Descriptions
Pin No.
29, 30, 31,
32, 1, 2
Mnemonic
Y0, Y1, Y2, Y3, Y4,
Y5
Type1
I
3, 4, 5
A0, A1, A2
I
6
RESET
I
7, 18, 21, 28
8, 17, 19
VDD
LDO
P
P/O
9, 10
11
XTAL
REF
I
I
12
13
14
15
CS
SCLK
SDIO
OUTSEL
I
I
I/O
I
16
20
26, 22
27, 23
24, 25
EP
FILTER
LOCKED
OUT1, OUT2
OUT1, OUT2
GND
Exposed Die Pad
I/O
O
O
O
P
1
Description
Control Pins. These pins select preset values for the PLL feedback divider and the OUT1
dividers based on the input reference frequency selected via the A[0:2] pins and have
internal 100 kΩ pull-up resistors.
Control Pins. These pins select the input reference frequency and have internal 100 kΩ pullup resistors.
Digital Input, Active High. Resets internal logic to default states. This pin has an internal
100 kΩ pull-up resistor, so the default state of the device is reset.
Power Supply Connection: 3.3 V Analog Supply.
LDO Decoupling Pins. Connect a 0.47 μF decoupling capacitor from each of these pins to
ground.
Crystal Resonator Input. Connect a crystal resonator across these pins.
Reference Clock Input. Connect this pin to an active clock input signal, or connect it to VDD
when using a crystal resonator across the XTAL pins.
Digital Input, Active Low, Chip Select.
Serial Data Clock.
Digital Serial Data Input/Output.
Logic 0 selects LVDS and Logic 1 selects LVPECL-compatible levels for both OUT1 and OUT2
when the outputs are not under SPI port control. Can be overridden via the programming
registers. This pin has an internal 100 kΩ pull-up resistor.
Loop Filter Node for the PLL. Connect an external 12 nF capacitor from this pin to Pin 17 (LDO).
Active High Locked Status Indicator for the PLL.
Complementary Square Wave Clocking Outputs.
Square Wave Clocking Outputs.
Analog Ground.
The exposed die pad must be connected to GND.
I = input, I/O = input/output, O = output, P = power, P/O = power/output.
Rev. C | Page 8 of 32
AD9552
TYPICAL PERFORMANCE CHARACTERISTICS
–30
–40
–50
–50
–60
–70
–60
–70
–80
–90
–100
–110
–120
–130
–140
–80
–90
–100
–110
–120
–130
–140
–150
–150
–160
–170
–180
100
–160
–170
–180
100
10k
100k
1M
FREQUENCY (Hz)
10M
100M
Figure 3. Phase Noise, Fractional-N, Pin Programmed
(fXTAL = 19.44 MHz, fOUT1 = 625 MHz)
CARRIER 624.999995MHz
0.4057dBm
–50
–50
–60
–70
–60
–70
PHASE NOISE (dB)
–30
–40
–80
–90
–100
–110
–120
–130
–140
–130
–140
–160
–170
–180
100
100M
Figure 4. Phase Noise, Fractional-N, Pin Programmed
(fREF = 19.44 MHz, fOUT1 = 625 MHz)
30
SUPPLY CURRENT (mA)
JITTER TRANSFER
–10
10M
100M
JITTER PEAKING
0
–30
–1
–40
–2
25
20
LVDS (STRONG)
15
10
–3
1k
10k
10k
LVPECL
LVDS (WEAK)
100k
100k
1M
FREQUENCY OFFSET (Hz)
10M
5
100
1k
FREQUENCY (MHz)
Figure 5. Jitter Transfer and Jitter Peaking
Figure 8. Supply Current vs. Output Frequency,
LVPECL and LVDS (15 pF Load)
Rev. C | Page 9 of 32
07806-019
1
07806-018
JITTER TRANSFER (dB)
10k
100k
1M
FREQUENCY (Hz)
35
0
–60
1k
1k
Figure 7. Phase Noise, Integer, SDM Off
(fREF = 19.44 MHz, fOUT1 = 622.08 MHz)
10
–50
0.3798dBm
–110
–120
–150
–20
100M
–100
–160
–170
–180
100
10M
10M
–80
–90
–150
10k
100k
1M
FREQUENCY (Hz)
10k
100k
1M
FREQUENCY (Hz)
CARRIER 622.079986MHz
–20
–30
–40
1k
1k
Figure 6. Phase Noise, Integer, SDM Off
(fXTAL = 19.44 MHz, fOUT1 = 622.08 MHz)
07806-015
PHASE NOISE (dB)
–20
0.5831dBm
07806-016
PHASE NOISE (dB)
–30
–40
1k
CARRIER 622.068199MHz
–20
07806-014
PHASE NOISE (dB)
0.4009dBm
07806-017
CARRIER 624.988784MHz
–20
AD9552
1.6
25
LVPECL
1.4
AMPLITUDE (V p-p)
15
10
1.2
LVDS (STRONG)
1.0
0.8
LVDS (WEAK)
5
0.6
0
50
100
150
FREQUENCY (MHz)
200
250
0.4
07806-020
0
0
Figure 9. Supply Current vs. Output Frequency,
CMOS (15 pF Load)
200
400
600
FREQUENCY (MHz)
800
1000
07806-023
SUPPLY CURRENT (mA)
20
Figure 12. Peak-to-Peak Output Voltage vs. Frequency,
LVPECL and LVDS (15 pF Load)
4.0
60
3.5
5pF
10pF
DUTY CYCLE (%)
AMPLITUDE (V p-p)
3.0
2.5
20pF
2.0
1.5
55
1.0
0
100
200
300
FREQUENCY (MHz)
400
500
07806-021
0
50
100
200
300
400
500
600
700
FREQUENCY (MHz)
800
900
1000
Figure 13. Duty Cycle vs. Output Frequency,
LVPECL and LVDS (15 pF Load)
Figure 10. Peak-to-Peak Output Voltage vs. Frequency,
CMOS
55
200mV/DIV
5pF
10pF
20pF
53
52
50
0
100
200
FREQUENCY (MHz)
300
500ps/DIV
Figure 11. Duty Cycle vs. Output Frequency, CMOS
Figure 14. Typical Output Waveform, LVPECL (805 MHz)
Rev. C | Page 10 of 32
07806-025
51
07806-022
DUTY CYCLE (%)
54
07806-024
LVDS (WEAK)
LVDS (STRONG)
LVPECL
0.5
1.25ns/DIV
Figure 15. Typical Output Waveform, LVDS
(805 MHz, 3.5 mA Drive Current)
Figure 16. Typical Output Waveform, CMOS
(250 MHz, 15 pF Load)
Rev. C | Page 11 of 32
07806-027
500mV/DIV
500ps/DIV
07806-026
100mV/DIV
AD9552
AD9552
INPUT/OUTPUT TERMINATION RECOMMENDATIONS
0.1µF
AD9552
3.3V
DIFFERENTIAL
OUTPUT
(LVDS OR
LVPECL MODE)
DOWNSTREAM
DEVICE
07806-028
0.1µF
Figure 17. AC-Coupled LVDS or LVPECL Output Driver
DOWNSTREAM
DEVICE
Figure 18. DC-Coupled LVDS or LVPECL Output Driver
Rev. C | Page 12 of 32
07806-029
HIGH
IMPEDANCE
INPUT
100Ω
AD9552
100Ω
3.3V
DIFFERENTIAL
OUTPUT
(LVDS OR
LVPECL MODE)
AD9552
THEORY OF OPERATION
LOCKED
DETECTOR
FILTER
AD9552
LOCK
DETECT
2
REFA
XTAL
2×
PFD
Y5:0
VCO
P0
P1
2
OUT1
N1
4 OR 5
Σ-Δ
MODULATOR
3
REGISTER BANK
N
MOD,
FRAC
3
6
PRECONFIGURED
DIVIDER VALUES
N, MOD, FRAC, P0, P1
P0, P1
07806-006
A2:0
1 TO 63
N = 4N1 + N0
XTAL
SERIAL
PORT
4 TO 11
CHARGE
PUMP
TUNING
CONTROL
OUT2
3350MHz TO
4050MHz
Figure 19. Detailed Block Diagram
PRESET FREQUENCY RATIOS
The frequency selection pins (A[2:0] and Y[5:0]) allow the user
to hardwire the device for preset input and output divider values
based on the pin logic states (see Figure 19). The pins decode
ground or open connections as Logic 0 or Logic 1, respectively.
Use the serial I/O port to change the divider values from the
preset values provided by the A[2:0] and Y[5:0] pins.
The A[2:0] pins select one of eight input reference frequencies
(see Table 9). The user supplies the input reference frequency by
connecting a single-ended clock signal to the REF pin or a crystal
resonator across the XTAL pins. If the A[2:0] pins select 10 MHz,
12 MHz, 12.8 MHz, or 16 MHz, the input frequency to the AD9552
doubles internally. Alternatively, if Register 0x1D[2] is set to 1,
the input frequency doubles.
Table 9. Input Reference Frequency Selection Pins
A2
0
0
0
0
1
1
1
1
A1
0
0
1
1
0
0
1
1
A0
0
1
0
1
0
1
0
1
Reference Frequency (MHz)
10.00
12.00
12.80
16.00
19.20
19.44
20.00
26.00
The Y[5:0] pins select the appropriate feedback and output dividers
to synthesize the output frequencies (see Table 10). The output
frequencies provided in Table 10 are exact; that is, the number of
decimal places displayed is sufficient to maintain full precision.
Where a decimal representation is not practical, a fractional
multiplier is used.
The VCO and output frequency shift in frequency by a ratio of the
reference frequency used vs. the frequency specified in Table 9.
Note that the VCO frequency must stay within the minimum and
maximum range specified in Table 1. Typically, the selection of
the VCO frequency band, as well as the gain adjustment, by the
external pin strap occurs as part of the device’s automatic VCO
calibration process, which initiates at power up (or reset). If the
user changes the VCO frequency band via the SPI interface,
however, a forced VCO calibration should be initiated by first
enabling SPI control of the VCO calibration (Register 0x0E[2] = 1)
and then writing a 1 to the calibrate VCO bit (Register 0x0E[7]).
Rev. C | Page 13 of 32
AD9552
Table 10. Output Frequency Selection Pins
Y5
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Y4
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
1
1
1
1
1
1
Y3
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
0
0
1
1
1
1
1
1
1
1
0
0
0
0
0
0
Y2
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
1
1
0
0
0
0
1
1
Y1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
1
1
0
0
Y0
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
0
1
VCO Frequency (MHz)
3732.48
3888
3840
3932.16
3750
3733.296
3560.439
3564
3732.48
3932.16
4000
3825
3840
4000
3724
3732.48
3750
3825
3867.188
3944.531
3999.086
4015.959
4023.878
3554.742
3932.16
4000
3732.48
3840
4000
3471.4
3718.75
3763.2
3984.375
3732.48
3748.229
3750
3763.978
3779.927
3840
3849.12
3867.188
3944.531
3961.105
3999.086
4014.769
4015.959
4017.857
4025.032
4032.976
3452.846
3467.415
3468.75
3481.996
3521.903
Rev. C | Page 14 of 32
Output (MHz)
51.84
54
60
61.44
62.5
66.666
74.17582
74.25
77.76
98.304
100
106.25
120
125
133
155.52
156.25
159.375
161.1328125
10518.75/64
155.52 × (15/14)
155.52 × (255/237)
167.6616
177.7371
245.76
250
311.04
320
400
433.925
531.25
537.6
569.1964
622.08
624.7048
625
622.08 × (239/237)
629.9878
640
641.52
625 × (66/64)
657.421875
657.421875 × (239/238)
622.08 × (15/14)
669.1281
622.08 × (255/237)
625 × (15/14)
670.8386
622.08 × (255/236)
625 × (66/64) × (15/14)
625 × (255/237) × (66/64)
693.75
622.08 × (253/226)
657.421875 × (255/238)
AD9552
Y5
1
1
1
1
1
1
1
1
1
1
Y4
1
1
1
1
1
1
1
1
1
1
Y3
0
0
1
1
1
1
1
1
1
1
Y2
1
1
0
0
0
0
1
1
1
1
Y1
1
1
0
0
1
1
0
0
1
1
Y0
0
1
0
1
0
1
0
1
0
1
VCO Frequency (MHz)
3536.763
3582.686
3593.75
3598.672
3740.355
3750
3888
3897.843
3906.25
4028.32
Output (MHz)
657.421875 × (255/237)
716.5372
718.75
719.7344
748.0709
750
777.6
779.5686
781.25
625 × (10/8) × (66/64)
COMPONENT BLOCKS
Reference Monitor
Input Reference
The REF input includes a monitor circuit that detects signal
presence at the REF input. If the device detects a clock signal on
the REF pin, it automatically selects the REF input as the input
reference source and shuts down the crystal oscillator. This automatic preference for a REF input signal is the default mode of
operation. However, the user can override the default setting via
Register 0x1D[0]. Setting this bit forces the device to override the
signal detector associated with the REF input and activates the
crystal oscillator (whether or not a REF input signal is present).
The AD9552 offers the following input reference options:
Crystal resonator connected directly across the XTAL pins
CMOS-compatible, single-ended clock source connected
directly to the REF pin
In the case of a crystal resonator, the AD9552 expects a crystal
with a specified load capacitance of 15 pF (default). The
AD9552 provides the load capacitance internally. The internal
load capacitance consists of a fixed component of 13 pF and a
variable (programmable) component of 0 pF to 15.75 pF.
After applying power to the AD9552 (or after a device reset),
the programmable component assumes a value of 2 pF. This
establishes the default load capacitance of 15 pF.
To accommodate crystals with a specified load capacitance other
than 15 pF (8 pF to 23.75 pF), the user can adjust the programmable capacitance in 0.25 pF increments via Register 0x1B[5:0].
Note that when the user sets Register 0x1B[7] to 0 (enabling SPI
control of the XTAL tuning capacitors), the variable capacitance
changes from 2 pF (its power-up value) to 15.75 pF due to the
default value of Register 0x1B[5:0]. This causes the crystal load
capacitance to be 23.75 pF until the user overwrites the default
contents of Register 0x1B[5:0].
A noncomprehensive, alphabetical list of crystal manufacturers
includes the following:
•
•
•
•
•
•
AVX/Kyocera
ECS
Epson Toyocom
Fox Electronics
NDK
Siward
2× Frequency Multiplier
The 2× frequency multiplier provides the option to double
the frequency delivered by either the REF or XTAL input. This
allows the user to take advantage of a higher frequency delivered to the PLL, which allows for greater separation between
the frequency generated by the PLL and the associated reference
spur. However, increased reference spur separation comes at the
expense of the harmonic spurs introduced by the frequency
multiplier. As such, beneficial use of the frequency multiplier
is application specific.
PLL
The PLL consists of a phase/frequency detector (PFD), a
partially integrated analog loop filter (see Figure 20), an
integrated voltage-controlled oscillator (VCO), and a
feedback divider with an optional third-order SDM that
allows for fractional divide ratios. The PLL produces a
nominal 3.7 GHz signal that is phase-locked to the input
reference signal.
The loop bandwidth of the PLL is nominally 50 kHz. The PFD of
the PLL drives a charge pump that automatically changes current
proportionately to the feedback divider value. This increase or
decrease in current maintains a constant loop bandwidth with
changes in the input reference or the output frequency.
The AD9552 evaluation board functions with the NDK
NX3225SA crystal or with the Siward 571200-A258-001 crystal.
Although these crystals meet the load capacitance and motional
resistance requirements of the AD9552 according to their data
sheets, Analog Devices, Inc., does not guarantee their operation
with the AD9552, nor does Analog Devices endorse one supplier
of crystals over another.
FROM
CHARGE
PUMP
Rev. C | Page 15 of 32
1.25kΩ
2.5kΩ
105pF
1.25kΩ
15pF
2.5kΩ
15pF
20pF
TO
VCO
16
07806-004
•
•
EXTERNAL
LOOP FILTER
CAPACITOR
Figure 20. Internal Loop Filter
AD9552
The gain of the PLL is proportional to the current delivered
by the charge pump. The user can override the default charge
pump current setting, and, thereby, the PLL gain, by using
Register 0x0A[7:0].
The PLL has a VCO with 128 frequency bands spanning a range
of 3350 MHz to 4050 MHz (3700 MHz nominal). However, the
actual operating frequency within a particular band depends on
the control voltage that appears on the loop filter capacitor. The
control voltage causes the VCO output frequency to vary linearly
within the selected band. This frequency variability allows the
control loop of the PLL to synchronize the VCO output signal
with the reference signal applied to the PFD. Typically, selection
of the VCO frequency band (as well as gain adjustment) occurs
automatically as part of the device’s automatic VCO calibration
process, which initiates at power up (or reset). Alternatively, the
user can force VCO calibration by first enabling SPI control of
VCO calibration (Register 0x0E[2] = 1) and then writing a 1 to
the calibrate VCO bit (Register 0x0E[7]). To facilitate system
debugging, the user can override the VCO band setting by first
enabling SPI control of VCO band (Register 0x0E[0] = 1) and
then writing the desired value to Register 0x10[7:1].
The PLL has a feedback divider coupled with a third-order
SDM that enables the PLL to provide integer-plus-fractional
frequency upconversion. The integer factor, N, is variable via
an 8-bit programming register. The range of N is from NMIN to
255, where NMIN is 36 or 47 depending on whether the SDM is
disabled or enabled, respectively. The SDM in the feedback path
allows for a fractional divide value that takes the form of N +
F/M, where N is the integer part (eight bits), M is the modulus
(20 bits), and F is the fractional part (20 bits), with all three
parameters being positive integers.
The feedback SDM gives the AD9552 the ability to support a
wide range of output frequencies with exact frequency ratios
relative to the input reference.
PLL Locked Indicator
The PLL provides a status indicator that appears at an external
pin (LOCKED). The indicator shows when the PLL has acquired
a locked condition.
Output Dividers
Two integer dividers exist in the output chain. The first divider (P0)
yields an integer submultiple of the VCO frequency. The second
divider (P1) establishes the frequency at OUT1 as an integer
submultiple of the output frequency of the P0 divider.
Input-to-OUT2 Option
By default, OUT2 delivers an output frequency that is the same
frequency as OUT1. However, the user has the option of making
OUT2 a replica of the input frequency (REF or XTAL) by
programming Register 33[3] = 1.
Output Drivers
The user has control over the following output driver parameters
via the programming registers:
•
•
•
•
Logic family and pin functionality
Polarity (for CMOS family only)
Drive current
Power-down
The logic families are LVDS, LVPECL, and CMOS. Selection of
the logic family is via the mode control bits in the OUT1 driver
control register (Register 0x32[5:3]) and the OUT2 driver control
register (Register 0x34[5:3]), as detailed in Table 11. Regardless
of the selected logic family, each output driver uses two pins:
OUT1 and OUT1 are used by one driver, and OUT2 and OUT2
are used by the other. This enables support of the differential
signals associated with the LVDS and LVPECL logic families.
CMOS, on the other hand, is a single-ended signal requiring
only one output pin, but both output pins are available for
optional provision of a dual, single-ended CMOS output clock.
Refer to the first entry (CMOS (both pins)) in Table 11.
Table 11. Output Channel Logic Family and Pin Functionality
Mode
Control Bits[2:0]
000
001
010
011
100
101
110
111
Logic Family and Pin Functionality
CMOS (both pins)
CMOS (positive pin), tristate (negative pin)
Tristate (positive pin), CMOS (negative pin)
Tristate (both pins)
LVDS
LVPECL
Undefined
Undefined
If the mode bits indicate the CMOS logic family, the user has
control of the logic polarity associated with each CMOS output
pin via the OUT1 and OUT2 driver control registers.
If the mode bits indicate the CMOS or LVDS logic family, the
user can select whether the output driver uses weak or strong
drive capability via the OUT1 and OUT2 driver control registers.
In the case of the CMOS family, the strong setting allows for
driving increased capacitive loads. In the case of the LVDS
family, the nominal weak and strong drive currents are 3.5 mA
and 7 mA, respectively.
The OUT1 and OUT2 driver control registers also have a powerdown bit to enable/disable the output drivers. The power-down
function is independent of the logic family selection.
Note that, unless the user programs the device to allow SPI port
control of the output drivers, the drivers default to LVPECL or
LVDS, depending on the logic level on the OUTSEL pin (Pin 15).
For OUTSEL = 0, both outputs are LVDS. For OUTSEL = 1, both
outputs are LVPECL. In the pin-selected LVDS mode, the user
can still control the drive strength, using the SPI port.
Rev. C | Page 16 of 32
AD9552
PART INITIALIZATION AND AUTOMATIC POWERON RESET
The frequency at the input to the PFD (fPFD) is calculated as
follows:
fPFD = K × fREF
The AD9552 has an internal power-on reset circuit. At power-up,
internal logic relies on the internal reference monitor to select
either the crystal oscillator or the reference input and then
initiates VCO calibration using whichever is found. If both are
present, the external reference path is chosen.
The operating range of the VCO (3.35 GHz ≤ fVCO ≤ 4.05 GHz)
places the following constraint on fPFD:
VCO calibration is required in order for the device to lock. If
the input reference signal is not present, VCO calibration waits
until a valid input reference is present. As soon as an input
reference signal is present, VCO calibration starts.
CALCULATING DIVIDER VALUES
If the user wishes to use the crystal oscillator input even if the
reference input is present, the user needs to set Bit 0 (use crystal
resonator) in Register 0x1D.
Any change to the preset frequency selection pins or the PLL
divide ratios requires the user to recalibrate the VCO.
OUTPUT/INPUT FREQUENCY RELATIONSHIP
The frequency at OUT1 and OUT2 is a function of the PLL
feedback divider values (N, FRAC, and MOD) and the output
divider values (P0 and P1). The equations that define the
frequency at OUT1 and OUT2 (fOUT1 and fOUT2, respectively)
are as follows.
⎛
N+
f OUT 1 = f REF ⎜⎜ K ×
P0 P1
⎝
FRAC
MOD
⎛ 3350
⎜
⎜ N + FRAC
MOD
⎝
⎞
⎟ MHz
⎟
⎠
This section provides a three-step procedure for calculating the
divider values when given a specific fOUT1/fREF ratio (fREF is the
frequency of either the REF input signal source or the external
crystal resonator). The computation process is described in
general terms, but a specific example is provided for clarity.
The example is based on a frequency control pin setting of
A[2:0] = 111 (see Table 9) and Y[5:0] = 101000 (see Table 10),
yielding the following:
fREF = 26 MHz
fOUT1 = 625 × (66/64) MHz
1.
Determine the output divide factor (ODF).
Note that the VCO frequency (fVCO) spans 3350 MHz to
4050 MHz. The ratio, fVCO/fOUT1, indicates the required ODF.
Given the specified value of fOUT1 (~644.53 MHz) and the
range of fVCO, the ODF spans a range of 5.2 to 6.3. The ODF
must be an integer, which means that ODF = 6 (because 6
is the only integer between 5.2 and 6.3).
⎞
⎟
⎟
⎠
fOUT2 = fOUT1
where:
fREF is the input reference or crystal resonator frequency.
K is the input mode scale factor.
N is the integer feedback divider value.
FRAC and MOD are the fractional feedback divider values.
P0 and P1 are the OUT1 divider values.
⎞
⎛
⎟ MHz ≤ f PFD ≤ ⎜ 4050
⎟
⎜ N + FRAC
MOD
⎠
⎝
2.
The numerator of the fOUT1 equation contains the feedback division
factor, which has an integer part (N) due to an integer divider
along with an optional fractional part (FRAC/MOD) associated
with the feedback SDM.
The following constraints apply:
N MIN ∈ {36 , 47}
N ∈ {N MIN , N MIN + 1,L, 255}
FRAC ∈ {0, 1, L, 1,048,575}
Determine suitable values for P0 and P1.
The ODF is the product of the two output dividers, so
ODF = P0P1. It has already been determined that ODF = 6
for the given example. Therefore, P0P1 = 6 with the constraints
that P0 and P1 are both integers and that 4 ≤ P0 ≤ 11 (see
the Output/Input Frequency Relationship section). These
constraints lead to the single solution: P0 = 6 and P1 = 1.
Although this particular example yields a single solution
for the output divider values with fOUT1 ≈ 644.53 MHz, some
fOUT1 frequencies result in multiple ODFs rather than just
one. For example, if fOUT1 = 100 MHz the ODF ranges from
34 to 40. This leads to an assortment of possible values for
P0 and P1, as shown in Table 12.
Table 12. Combinations for P0 and P1
MOD ∈ {1, 2 , L, 1,048,575}
K ∈ {1, 2}
P0 ∈{4 , 5,L,11}
P1 ∈{1, 2,L, 63}
Note that NMIN and K can each be one of two values. The value
of NMIN depends on the state of the SDM. NMIN = 36 when the
SDM is disabled or NMIN = 47 when it is enabled. The value of K
depends on the 2× frequency multiplier. K = 1 when the 2×
frequency multiplier is bypassed, or K = 2 when it is enabled.
Rev. C | Page 17 of 32
P0
4
4
5
5
6
7
8
9
10
P1
9
10
7
8
6
5
5
4
4
ODF (P0 × P1)
36
40
35
40
36
35
40
36
40
AD9552
The P0 and P1 combinations listed in Table 12 are all equally
valid. However, note that they yield only three valid ODF
values (35, 36, and 40) from the original range of 34 to 40.
3.
Determine the feedback divider values for the PLL.
In the example, N = 148 and R/Y = 1228/1664, which reduces
to R/Y = 307/416. These values of N, R, and Y constitute the
following respective feedback divider values:
N = 148, FRAC = 307, and MOD = 416.
Repeat this step for each ODF when multiple ODFs exist
(for example, 35, 36, and 40 in the case of Table 12).
The only caveat is that N and MOD must meet the constraints
given in the Output/Input Frequency Relationship section.
To calculate the feedback divider values for a given ODF,
use the following equation:
In the example, FRAC is nonzero, so the division value is an
integer plus the fractional component, FRAC/MOD. This
implies that the feedback SDM is necessary as part of the
feedback divider. If FRAC = 0, the feedback division factor
is an integer and the SDM is not required (it can be bypassed).
⎛ f OUT 1
⎜
⎜ f
⎝ REF
⎞
X
⎟ × ODF =
⎟
Y
⎠
Note that the left side of the equation contains variables with
known quantities. Furthermore, the values are necessarily
rational, so the left side is expressible as a ratio of two integers, X and Y. Following is an example equation.
⎛
⎡ 66 ⎤ ⎞
⎜ 625⎢ ⎥ ⎟
⎣ 64 ⎦ ⎟ × 6 = 625(66)(6) = 247,500 = X
⎜
⎜ 26 ⎟
Y
26(64)
1664
⎟
⎜
⎠
⎝
In the context of the AD9552, X/Y is always an improper
fraction. Therefore, it is expressible as the sum of an integer,
N, and the proper fraction, R/Y (R and Y are integers).
X
R
=N+
Y
Y
247,500
R
=N+
1664
Y
This particular example yields N = 148, Y = 1664, and
R = 1228. To arrive at this result, use long division to convert
the improper fraction, X/Y, to an integer (N) and a proper
fraction (R/Y). Note that dividing Y into X by means of
long division yields an integer, N, and a remainder, R. The
proper fraction has a numerator (R, the remainder) and a
denominator (Y, the divisor), as shown in Figure 21.
X
R
=N+
Y
Y
Δf =
f PFD
MOD
Because the SDM is in the feedback path of the PLL, these spurs
appear in the output signal as spurious components offset by Δf
from fOUT1. Therefore, a small MOD value pro-duces relatively
large spurs with relatively large frequency offsets from fOUT1,
whereas a large MOD value produces smaller spurs but more
closely spaced to fOUT1. Clearly, the value of MOD has a direct
impact on the spurious content (that is, jitter) at OUT1.
Generally, the largest possible MOD value yields the smallest spurs.
Thus, it is desirable to scale MOD and FRAC by the integer part
of 220 divided by the value of MOD obtained previously. In the
example, the value of MOD is 416, yield-ing a scale factor of 2520
(the integer part of 220/416). A scale factor of 2520 leads to FRAC
= 307 × 2520 = 773,640 and MOD = 416 × 2520 = 1,048,320.
LOW DROPOUT (LDO) REGULATORS
07806-005
N
Y X
–NY
R
Although the feedback divider values obtained in this way
provide the proper feedback divide ratio to synthesize the exact
output frequency, they may not yield optimal jitter performance
at the final output. One reason for this is that the value of MOD
defines the period of the SDM, which has a direct impact on the
spurious output of the SDM. Specifically, in the spectral band
from dc to fPFD, the SDM exhibits spurs at intervals of fPFD/
MOD. Thus, the spectral separation (Δf) of the spurs associated
with the feedback SDM is
Figure 21. Example Long Division
It is imperative that long division be used to obtain the correct
results. Avoid the use of a calculator or math program, because
these do not always yield correct results due to internal rounding
and/or truncation. Some calculators or math programs may be up
to the task if they can handle very large integer operations, but such
are not common.
The AD9552 is powered from a single 3.3 V supply and contains
on-chip LDO regulators for each function to eliminate the need
for external LDOs. To ensure optimal performance, each LDO
output should have a 0.47 μF capacitor connected between its
access pin and ground, and this capacitor should be kept as
close to the device as possible.
Rev. C | Page 18 of 32
AD9552
APPLICATIONS INFORMATION
THERMAL PERFORMANCE
Table 13. Thermal Parameters for the 32-Lead LFCSP Package
Symbol
θJA
θJMA
θJMA
θJB
θJC
ΨJT
1
2
Thermal Characteristic Using a JEDEC51-7 Plus JEDEC51-5 2S2P Test Board 1
Junction-to-ambient thermal resistance, 0.0 m/sec airflow per JEDEC JESD51-2 (still air)
Junction-to-ambient thermal resistance, 1.0 m/sec airflow per JEDEC JESD51-6 (moving air)
Junction-to-ambient thermal resistance, 2.5 m/sec airflow per JEDEC JESD51-6 (moving air)
Junction-to-board thermal resistance, 1.0 m/sec airflow per JEDEC JESD51-8 (moving air)
Junction-to-case thermal resistance (die-to-heat sink) per MIL-Std 883, Method 1012.1
Junction-to-top-of-package characterization parameter, 0 m/sec airflow per JEDEC JESD51-2 (still air)
Value 2
40.5
35.4
31.8
23.3
4.2
0.4
Unit
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
The exposed pad on the bottom of the package must be soldered to ground to achieve the specified thermal performance.
Results are from simulations. The PCB is a JEDEC multilayer type. Thermal performance for actual applications requires careful inspection of the conditions in the
application to determine whether they are similar to those assumed in these calculations.
The AD9552 is specified for a case temperature (TCASE). To
ensure that TCASE is not exceeded, an airflow source can be used.
Use the following equation to determine the junction temperature on the application PCB:
TJ = TCASE + (ΨJT × PD)
where:
TJ is the junction temperature (°C).
TCASE is the case temperature (°C) measured by the customer
at the top center of the package.
ΨJT is the value indicated in Table 13.
PD is the power dissipation (see the Specifications section).
Values of θJA are provided for package comparison and PCB design
considerations. θJA can be used for a first-order approximation
of TJ using the following equation:
TJ = TA + (θJA × PD)
where TA is the ambient temperature (°C).
Values of θJC are provided for package comparison and PCB
design considerations when an external heat sink is required.
Values of θJB are provided for package comparison and PCB
design considerations.
Rev. C | Page 19 of 32
AD9552
SERIAL CONTROL PORT
The AD9552 serial control port is a flexible, synchronous, serial
communications port that allows an easy interface to many
industry-standard microcontrollers and microprocessors. Single
or multiple byte transfers are supported, as well as MSB first or
LSB first transfer formats. The AD9552 serial control port is
configured for a single bidirectional I/O pin (SDIO only).
The serial control port has two types of registers: read-only and
buffered. Read-only registers are nonbuffered and ignore write
commands. All writable registers are buffered (also referred to
as mirrored) and require an I/O update to transfer the new values
from a temporary buffer on the chip to the actual register. To
invoke an I/O update, write a 1 to the I/O update bit found in
Register 0x05[0]. Because any number of bytes of data can
be changed before issuing an update command, the update
simultaneously enables all register changes occurring since
any previous update.
SERIAL CONTROL PORT PIN DESCRIPTIONS
SCLK (serial data clock) is the serial shift clock. This pin is an
input. SCLK is used to synchronize serial control port reads and
writes. Write data bits are registered on the rising edge of this
clock, and read data bits are registered on the falling edge. This
pin is internally pulled down by a 30 kΩ resistor to ground.
SDIO (digital serial data input/output) is a dual-purpose pin
that acts as input only or as an input/output. The AD9552
defaults to bidirectional pins for I/O.
CS (chip select bar) is an active low control that gates the read and
write cycles. When CS is high, SDIO is in a high impedance state.
This pin is internally pulled up by a 100 kΩ resistor to 3.3 V. It
should not be left floating. See the Operation of the Serial Control
Port section on the use of the CS pin in a communication cycle.
13
AD9552
SDIO
14
SERIAL
CONTROL
PORT
CS
12
Table 14. Byte Transfer Count
W1
0
0
1
1
W0
0
1
0
1
Bytes to Transfer
(Excluding the 2-Byte Instruction)
1
2
3
Streaming mode
In the streaming mode (Bits[W1:W0] = 11), any number of data
bytes can be transferred in a continuous stream. The register
address is automatically incremented or decremented (see the
MSB/LSB First Transfers section). CS must be raised at the end
of the last byte to be transferred, thereby ending the stream mode.
Communication Cycle—Instruction Plus Data
There are two parts to a communication cycle with the AD9552.
The first part writes a 16-bit instruction word into the AD9552,
coincident with the first 16 SCLK rising edges. The instruction
word provides the AD9552 serial control port with information
regarding the data transfer, which is the second part of the
communication cycle. The instruction word defines whether
the upcoming data transfer is a read or a write, the number of
bytes in the data transfer, and the starting register address for
the first byte of the data transfer.
Write
If the instruction word is for a write operation (Bit I15 = 0), the
second part is the transfer of data into the serial control port
buffer of the AD9552. The length of the transfer (1, 2, or 3 bytes;
or streaming mode) is indicated by two bits (Bits[W1:W0]) in
the instruction byte. The length of the transfer indicated by
(Bits[W1:W0]) does not include the 2-byte instruction. CS can
be raised after each sequence of eight bits to stall the bus (except
after the last byte, where it ends the cycle). When the bus is stalled,
the serial transfer resumes when CS is lowered. Stalling on nonbyte
boundaries resets the serial control port.
07806-006
SCLK
the serial control port state machine enters a wait state until all
data has been sent. If the system controller decides to abort before
the complete transfer of all the data, the state machine must be reset
either by completing the remaining transfer or by returning the
CS line low for at least one complete SCLK cycle (but fewer than
eight SCLK cycles). A rising edge on the CS pin on a nonbyte
boundary terminates the serial transfer and flushes the buffer.
Figure 22. Serial Control Port
OPERATION OF THE SERIAL CONTROL PORT
Framing a Communication Cycle with CS
The CS line gates the communication cycle (a write or a read operation). CS must be brought low to initiate a communication cycle.
The CS stall high function is supported in modes where three
or fewer bytes of data (plus instruction data) are transferred.
Bits[W1:W0] must be set to 00, 01, or 10 (see Table 14). In these
modes, CS may temporarily return high on any byte boundary,
allowing time for the system controller to process the next byte.
CS can go high on byte boundaries only and can go high during
either part (instruction or data) of the transfer. During this period,
Read
If the instruction word is for a read operation (Bit I15 = 1), the
next N × 8 SCLK cycles clock out the data from the address
specified in the instruction word, where N is 1, 2, 3, or 4, as
determined by Bits[W1:W0]. In this case, 4 is used for streaming
mode, where four or more words are transferred per read. The
data read back is valid on the falling edge of SCLK.
The default mode of the AD9552 serial control port is bidirectional mode, and the data read back appears on the SDIO pin.
Rev. C | Page 20 of 32
AD9552
SDIO
14
CS
SERIAL
CONTROL
PORT
12
REGISTER
UPDATE
EXECUTE AN
INPUT/OUTPUT
UPDATE
MSB/LSB FIRST TRANSFERS
The AD9552 instruction word and byte data can be MSB first or
LSB first. The default for the AD9552 is MSB first. The LSB first
mode can be set by writing a 1 to Register 0x00[6] and requires
that an I/O update be executed. Immediately after the LSB first
bit is set, all serial control port operations are changed to LSB
first order.
AD9552
CORE
When MSB first mode is active, the instruction and data bytes
must be written from MSB to LSB. Multibyte data transfers in
MSB first format start with an instruction byte that includes the
register address of the most significant data byte. Subsequent
data bytes must follow in order from high address to low address.
In MSB first mode, the serial control port internal address generator decrements for each data byte of the multibyte transfer cycle.
07806-007
13
CONTROL REGISTERS
SCLK
REGISTER BUFFERS
By default, a read request reads the register value that is currently
in use by the AD9552. However, setting Register 0x04[0] = 1
causes the buffered registers to be read instead. The buffered
registers are the ones that take effect during the next I/O update.
Figure 23. Relationship Between the Serial Control Port Register Buffers and
the Control Registers
The AD9552 uses Register 0x00 to Register 0x34. Although the
AD9552 serial control port allows both 8-bit and 16-bit instructions, the 8-bit instruction mode provides access to five address
bits (Address Bits[A4:A0]) only, which restricts its use to Address
Space 0x00 to Address Space 0x01. The AD9552 defaults to 16-bit
instruction mode on power-up, and the 8-bit instruction mode
is not supported.
When LSB first = 1 (LSB first), the instruction and data bytes
must be written from LSB to MSB. Multibyte data transfers
in LSB first format start with an instruction byte that includes
the register address of the least significant data byte followed
by multiple data bytes. The serial control port internal byte
address generator increments for each data byte of the multibyte
transfer cycle.
INSTRUCTION WORD (16 BITS)
The AD9552 serial control port register address decrements from
the register address just written toward 0x00 for multibyte I/O
operations if the MSB first mode is active (default). If the LSB
first mode is active, the serial control port register address
increments from the address just written toward 0x34 for
multibyte I/O operations.
The MSB of the instruction word (see Table 15) is R/W, which
indicates whether the instruction is a read or a write. The next
two bits, W1 and W0, are the transfer length in bytes. The final
13 bits are the address bits (Address Bits[A12:A0]) at which the
read or write operation is to begin.
For a write, the instruction word is followed by the number of
bytes of data indicated by Bits[W1:W0], which is interpreted
according to Table 14.
Unused addresses are not skipped during multibyte I/O operations.
The user should write the default value to a reserved register and
should write only zeros to unmapped registers. Note that it is more
efficient to issue a new write command than to write the default
value to more than two consecutive reserved (or unmapped)
registers.
Address Bits[A12:A0] select the address within the register map
that is written to or read from during the data transfer portion
of the communication cycle. The AD9552 uses all of the 13-bit
address space. For multibyte transfers, this address is the starting
byte address.
Table 15. Serial Control Port, 16-Bit Instruction Word, MSB First
MSB
I15
R/W
I14
W1
I13
W0
I12
A12
I11
A11
I10
A10
I9
A9
I8
A8
I7
A7
I6
A6
I5
A5
Table 16. Definition of Terms Used in Serial Control Port Timing Diagrams
Parameter
tCLK
tDV
tDS
tDH
tS
tH
tHIGH
tLOW
Description
Period of SCLK
Read data valid time (time from falling edge of SCLK to valid data on SDIO)
Setup time between data and rising edge of SCLK
Hold time between data and rising edge of SCLK
Setup time between CS and SCLK
Hold time between CS and SCLK
Minimum period that SCLK should be in a logic high state
Minimum period that SCLK should be in a logic low state
Rev. C | Page 21 of 32
I4
A4
I3
A3
I2
A2
I1
A1
LSB
I0
A0
AD9552
CS
SCLK DON'T CARE
R/W W1 W0 A12 A11 A10 A9 A8 A7
A6 A5
A4 A3 A2
A1 A0
D7 D6 D5 D4 D3
16-BIT INSTRUCTION HEADER
D2 D1
D0
D7
REGISTER (N) DATA
D6 D5
D4 D3 D2
D1 D0
DON'T CARE
REGISTER (N – 1) DATA
07806-008
SDIO DON'T CARE
DON'T CARE
Figure 24. Serial Control Port Write—MSB First, 16-Bit Instruction, Two Bytes Data
CS
SCLK
SDIO
DON'T CARE
R/W W1 W0 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0
16-BIT INSTRUCTION HEADER
REGISTER (N) DATA
REGISTER (N – 1) DATA
REGISTER (N – 2) DATA
REGISTER (N – 3) DATA
07806-009
DON'T CARE
Figure 25. Serial Control Port Read—MSB First, 16-Bit Instruction, Four Bytes Data
tHIGH
tDS
tS
tDH
tH
tCLK
tLOW
CS
DON'T CARE
SDIO
DON'T CARE
DON'T CARE
R/W
W1
W0
A12
A11
A10
A9
A8
A7
A6
A5
D4
D3
D2
D1
D0
DON'T CARE
07806-010
SCLK
Figure 26. Serial Control Port Write—MSB First, 16-Bit Instruction, Timing Measurements
CS
SCLK
SDIO
DATA BIT N
07806-011
tDV
DATA BIT N – 1
Figure 27. Timing Diagram for Serial Control Port Register Read
CS
SCLK DON'T CARE
A4
A5 A6 A7
A8 A9 A10 A11 A12 W0 W1 R/W D0 D1 D2 D3 D4
16-BIT INSTRUCTION HEADER
D5 D6
D7 D0
REGISTER (N) DATA
D1 D2
D3 D4 D5
D6
REGISTER (N + 1) DATA
Figure 28. Serial Control Port Write—LSB First, 16-Bit Instruction, Two Bytes Data
tS
tH
CS
tCLK
tHIGH
SCLK
tLOW
tDS
tDH
SDIO
BIT N
BIT N + 1
Figure 29. Serial Control Port Timing—Write
Rev. C | Page 22 of 32
D7
DON'T CARE
07806-012
A0 A1 A2 A3
07806-013
SDIO DON'T CARE
DON'T CARE
AD9552
REGISTER MAP
A bit that is labeled “aclr” is an active high, autoclearing bit. When set to a Logic 1 state, the control logic automatically returns it to a
Logic 0 state upon completion of the indicated task.
Table 17. Register Map
Addr.
(Hex)
0x00
0x04
0x05
0x0A
0x0B
0x0C
0x0D
0x0E
0x0F
Register
Name
Serial port
control
Readback
control
I/O update
PLL charge
pump and
PFD
control
PLL charge
pump and
PFD
control
PLL charge
pump and
PFD
control
PLL charge
pump and
PFD
control
VCO
control
0x11
VCO
control
VCO
control
PLL control
0x12
0x13
0x14
PLL control
PLL control
PLL control
0x15
0x16
0x17
0x18
0x19
PLL control
PLL control
PLL control
PLL control
PLL control
0x1A
Input
receiver and
band gap
0x1B
XTAL
tuning
control
0x10
(MSB) Bit 7
0
Bit 6
LSB first
Bit 4
1
Bit 3
1
Bit 2
Soft reset
Bit 1
LSB first
Unused
Bit 5
Soft reset
(aclr)
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
Unused
(LSB)
Bit 0
0
Readback
control
I/O update
(aclr)
Charge pump current control[7:0]
(3.5 μA granularity, ~900 μA full scale)
Enable SPI
control of
charge
pump
current
Unused
Enable SPI
control of
antibacklash
period
CP offset
current
polarity
Antibacklash control[1:0]
Calibrate
VCO (aclr)
Enable
ALC
0x00
0x80
Enable CP
mode
control
PFD
feedback
input edge
control
PFD
reference
input edge
control
Force VCO
to
midpoint
frequency
0x30
CP offset current[1:0]
Enable CP
offset
current
control
Unused
Reserved
Reserved
Reserved
0x00
Unused
Unused
0x00
Enable SPI
control of
VCO
calibration
Boost VCO
supply
PLL lock
detector
powerdown
Enable SPI
control of
VCO band
setting
Unused
0x70
Unused
0x80
Reset PLL
0x80
0x00
0x00
Unused
Unused
ALC threshold[2:0]
Unused
VCO band control[6:0]
N[7:0] (SDM integer part)
MOD[19:12] (SDM modulus)
MOD[11:4] (SDM modulus)
MOD[3:0] (SDM modulus)
Enable SPI
Bypass
SDM
control of
output
frequency
FRAC[19:12] (SDM fractional part)
FRAC[11:4] (SDM fractional part)
FRAC[3:0] (SDM fractional part)
Unused
Unused
P1 divider[4:0]
Enable SPI
Unused
Unused
control
of OUT1
dividers
Receiver
Band gap voltage adjust[4:0]
reset (aclr)
(00000 = maximum, 11111 = minimum)
Unused
0x00
CP mode[1:0]
VCO level control[5:0]
Disable SPI
control of
XTAL tuning
capacitance
Default
0x18
0x00
Disable SDM
Unused
P0 divider[2:0]
P1 divider[5]
Unused
Enable SPI
control of
band gap
voltage
XTAL tuning capacitor control[5:0]
(0.25 pF per bit, inverted binary coding)
Rev. C | Page 23 of 32
0x80
0x20
0x00
0x01
0x00
0x20
0x00
0x80
AD9552
Addr.
(Hex)
0x1C
0x1D
Register
Name
XTAL
control
XTAL
control
(MSB) Bit 7
Unused
Bit 6
Unused
Bit 5
Unused
Bit 4
Unused
Bit 3
Unused
Bit 2
Unused
Unused
Unused
Unused
Unused
Unused
Select 2×
Unused
frequency
multiplier
OUT1 CMOS polarity[1:0]
0x32
OUT1
driver
control
OUT1 drive
strength
OUT1
powerdown
0x33
Select OUT2
source
OUT2
driver
control
Unused
Unused
OUT2 drive
strength
OUT2
powerdown
0x34
OUT1 mode control[2:0]
Unused
Unused
OUT2
source
OUT2 mode control[2:0]
Unused
Bit 1
Unused
Unused
OUT2 CMOS polarity[1:0]
(LSB)
Bit 0
Unused
Default
0x00
Use crystal
resonator
0x00
Enable SPI
control of
OUT1
driver
control
Unused
0xA8
Enable SPI
control of
OUT2
driver
control
0xA8
0x00
REGISTER MAP DESCRIPTIONS
Control bit functions are active high unless stated otherwise. Register address values are always hexadecimal unless otherwise indicated.
Serial Port Control (Register 0x00 to Register 0x05)
Table 18.
Address
0x00
0x04
0x05
Bit
7
6
Bit Name
Unused
LSB first
5
4
Soft reset
Unused
[3:0]
[7:1]
0
Unused
Unused
Readback control
[7:1]
0
Unused
I/O update
Description
Forced to Logic 0 internally, which enables 3-wire mode only.
Bit order for SPI port.
0 = most significant bit and byte first (default).
1 = least significant bit and byte first.
Software initiated reset (register values set to default). This is an autoclearing bit.
Forced to Logic 1 internally, which enables 16-bit mode (the only mode supported by
the device).
Mirrored version of the contents of Register 0x00[7:4] (that is, Bits[3:0] = Bits[7:4]).
Unused.
For buffered registers, serial port readback reads from actual (active) registers instead of
from the buffer.
0 = reads values currently applied to the internal logic of the device (default).
1 = reads buffered values that take effect on next assertion of I/O update.
Unused.
Writing a 1 to this bit transfers the data in the serial I/O buffer registers to the internal
control registers of the device. This is an autoclearing bit.
Rev. C | Page 24 of 32
AD9552
PLL Charge Pump and PFD Control (Register 0x0A to Register 0x0D)
Table 19.
Address
0x0A
Bit
[7:0]
Bit Name
Charge pump current control
0x0B
7
Enable SPI control of charge
pump current
6
Enable SPI control of
antibacklash period
[5:4]
CP mode
3
Enable CP mode control
2
PFD feedback input edge control
1
PFD reference input edge control
0
Force VCO to midpoint frequency
7
6
Unused
CP offset current polarity
[5:4]
CP offset current
3
Enable CP offset current control
2:0
[7:6]
Reserved
Antibacklash control
[5:1]
0
Unused
PLL lock detector power-down
0x0C
0x0D
Description
These bits set the magnitude of the PLL charge pump current. The granularity is
~3.5 μA with a full-scale magnitude of ~900 μA. Register 0x0A is ineffective unless
Register 0x0B[7] = 1. Default is 0x80, or ~448 μA.
Controls functionality of Register 0x0A.
0 = the device automatically controls the charge pump current (default).
1 = charge pump current defined by Register 0x0A.
Controls functionality of Register 0x0D[7:6].
0 = the device automatically controls the antibacklash period (default).
1 = antibacklash period defined by Register 0x0D[7:6].
Controls the mode of the PLL charge pump.
00 = tristate.
01 = pump up.
10 = pump down.
11 = normal (default).
Controls functionality of Bits[5:4] (CP mode).
0 = the device automatically controls the charge pump mode (default).
1 = charge pump mode is defined by Bits[5:4].
Selects the polarity of the active edge of the PLL’s feedback input.
0 = positive edge (default).
1 = negative edge.
Selects the polarity of the active edge of the PLL’s reference input.
0 = positive edge (default).
1 = negative edge.
Selects VCO control voltage functionality.
0 = normal VCO operation (default).
1 = force VCO control voltage to midscale.
Unused.
Selects the polarity of the charge pump offset current of the PLL. This bit is ineffective
unless Bit 3 = 1.
0 = pump up (default).
1 = pump down.
Controls the magnitude of the charge pump offset current of the PLL as a fraction of
the value in Register 0x0A. This bit is ineffective unless Bit 3 = 1.
00 = 1/2 (default).
01 = 1/4.
10 = 1/8.
11 = 1/16.
Controls functionality of Bits[6:4].
0 = the device automatically controls charge pump offset current (default).
1 = charge pump offset current defined by Bits[6:4].
Controls the PFD antibacklash period of the PLL. These bits are ineffective unless
Register 0x0B[6] = 1.
00 = minimum (default).
01 = low.
10 = high.
11 = maximum.
Unused.
Controls power-down of the PLL lock detector.
0 = lock detector active (default).
1 = lock detector powered down.
Rev. C | Page 25 of 32
AD9552
VCO Control (Register 0x0E to Register 0x10)
Table 20.
Address
0x0E
Bit
7
6
Bit Name
Calibrate VCO
Enable ALC
[5:3]
ALC threshold
2
Enable SPI control of VCO
calibration
1
Boost VCO supply
0
Enable SPI control of VCO band
setting
0x0F
[7:2]
VCO level control
0x10
[1:0]
[7:1]
Unused
VCO band control
0
Unused
Description
Initiates VCO calibration (this is an autoclearing bit). This bit is ineffective unless Bit 2 = 1.
Enables automatic level control (ALC) of the VCO.
0 = Register 0x0F[7:2] defines the VCO level.
1 = the device automatically controls the VCO level (default).
Controls the VCO ALC threshold detector level from minimum (000) to maximum
(111).
The default is 110.
Enables functionality of Bit 7.
0 = the device automatically performs VCO calibration (default).
1 = Bit 7 controls VCO calibration.
Selects VCO supply voltage.
0 = normal supply voltage (default).
1 = increase supply voltage by 100 mV.
Controls VCO band setting functionality.
0 = the device automatically selects the VCO band (default).
1 = VCO band defined by Register 0x10[7:1].
Controls the VCO amplitude from minimum (00 0000) to maximum (11 1111). The
default is 10 0000.
These bits are ineffective unless 0x0E[6] = 0.
Unused.
Controls the VCO frequency band from minimum (000 0000) to maximum (111 1111).
The default is 100 0000.
Unused.
PLL Control (Register 0x11 to Register 0x19)
Table 21.
Address
0x11
Bit
[7:0]
Bit Name
N
0x12
0x13
0x14
[7:0]
[7:0]
[7:4]
MOD
MOD
MOD
3
Enable SPI control of
output frequency
2
Bypass SDM
1
Disable SDM
0
Reset PLL
[7:0]
[7:0]
[7:4]
FRAC
FRAC
FRAC
[3:1]
0
Unused
P1 divider
0x15
0x16
0x17
Description
The 8-bit integer divide value for the SDM. Default is 0x00.
Note that operational limitations impose a lower boundary of 64 (0x40) on N.
Bits[19:12] of the 20-bit modulus of the SDM.
Bits[11:4] of the 20-bit modulus of the SDM.
Bits[3:0] of the 20-bit modulus of the SDM.
Default is MOD = 1000 0000 0000 0000 0000 (524,288).
Controls output frequency functionality.
0 = output frequency defined by the Y[3:0] pins (default).
1 = contents of Register 0x11 to Register 0x17 define output frequency via N, MOD, and FRAC.
Controls bypassing of the SDM.
0 = allow integer-plus-fractional division (default).
1 = allow only integer division.
Controls the SDM internal clocks.
0 = normal operation (SDM clocks active) (default).
1 = SDM disabled (SDM clocks stopped).
Controls initialization of the PLL.
0 = normal operation (default).
1 = resets the counters and logic associated with the PLL but does not affect the output dividers.
Bits[19:12] of the 20-bit fractional part of the SDM.
Bits[11:4] of the 20-bit fractional part of the SDM.
Bits[3:0] of the 20-bit fractional part of the SDM.
Default is FRAC = 0010 0000 0000 0000 0000 (131,072).
Write zeros to these bits when programming this register.
Bit 5 of the 6-bit P1 divider for OUT1.
Rev. C | Page 26 of 32
AD9552
Address
0x18
0x19
Bit
[7:3]
Bit Name
P1 divider
[2:0]
P0 divider
7
Enable SPI control of
OUT1 dividers
[6:0]
Unused
Description
Bits[4:0] of the 6-bit P1 divider for OUT1 (1 ≤ P1 ≤ 63). Do not set these bits to 000000. Default is
P1 = 10 0000 (32). The P1 bits are ineffective unless Register 0x19[7] = 1.
The 3-bit P0 divider for OUT1. The P0 divide value is as follows:
000 = 4 (default).
001 = 5.
010 = 6.
011 = 7.
100 = 8.
101 = 9.
110 = 10.
111 = 11.
The P0 bits are ineffective unless Register 0x19[7] = 1.
Controls functionality of OUT1 dividers.
0 = OUT1 dividers defined by the Y[5:0] pins (default).
1 = contents of Register 0x17 and Register 0x18 define OUT1 dividers (P0 and P1).
Unused.
Input Receiver and Band Gap Control (Register 0x1A)
Table 22.
Address
0x1A
Bit
7
Bit Name
Receiver reset
[6:2]
Band gap voltage adjust
1
0
Unused
Enable SPI control of band gap
voltage
Description
Input receiver reset control. This is an autoclearing bit.
0 = normal operation (default).
1 = reset input receiver logic.
Controls the band gap voltage setting from minimum (0 0000) to maximum (1 1111).
Default is 0 0000.
Unused.
Enables functionality of Bits[6:2].
0 = the device automatically selects receiver band gap voltage (default).
1 = Bits[6:2] define the receiver band gap voltage.
XTAL Control (Register 0x1B to Register 0x1D)
Table 23.
Address
0x1B
0x1C
0x1D
Bit
7
Bit Name
Disable SPI control of XTAL
tuning capacitance
6
[5:0]
Unused
XTAL tuning capacitor control
[7:0]
[7:3]
2
Unused
Unused
Select 2× frequency multiplier
1
0
Unused
Use crystal resonator
Description
Disables functionality of Bits[5:0].
0 = tuning capacitance defined by Bits[5:0].
1 = the device automatically selects XTAL tuning capacitance (default).
Unused.
Capacitance value coded as inverted binary (0.25 pF per bit); that is, 111111 is 0 pF,
111110 is 0.25 pF, and so on. The default value, 000000, is 15.75 pF.
Unused.
Unused.
Select/bypass the 2× frequency multiplier.
0 = bypassed (default).
1 = selected.
Unused.
Automatic external reference select override.
0 = the device automatically selects the external reference path if an external
reference signal is present (default).
1 = the device uses the crystal resonator input whether or not an external reference
signal is present.
Rev. C | Page 27 of 32
AD9552
OUT1 Driver Control (Register 0x32)
Table 24.
Address
0x32
Bit
7
Bit Name
OUT1 drive strength
6
OUT1 power-down
[5:3]
OUT1 mode control
[2:1]
OUT1 CMOS polarity
0
Enable SPI control of OUT1
driver control
Description
Controls the output drive capability of the OUT1 driver.
0 = weak.
1 = strong (default).
Controls power-down functionality of the OUT1 driver.
0 = OUT1 active (default).
1 = OUT1 powered down.
OUT1 driver mode selection.
000 = CMOS, both pins active.
001 = CMOS, positive pin active, negative pin tristate.
010 = CMOS, positive pin tristate, negative pin active.
011 = CMOS, both pins tristate.
100 = LVDS.
101 = LVPECL (default).
110 = not used.
111 = not used.
Selects the polarity of the OUT1 pins in CMOS mode.
00 = positive pin logic is true = 1, false = 0/negative pin logic is true = 0, false = 1 (default).
01 = positive pin logic is true = 1, false = 0/negative pin logic is true = 1, false = 0.
10 = positive pin logic is true = 0, false = 1/negative pin logic is true = 0, false = 1.
11 = positive pin logic is true = 0, false = 1/negative pin logic is true = 1, false = 0.
These bits are ineffective unless Bits[5:3] select CMOS mode.
Controls OUT1 driver functionality.
0 = OUT1 is LVDS or LVPECL, per the OUTSEL pin (Pin 15) (default).
1 = OUT1 functionality defined by Bits[7:1].
Select OUT2 Source Control (Register 0x33)
Table 25.
Address
0x33
Bit
[7:4]
3
Bit Name
Unused
OUT2 source
[2:0]
Unused
Description
Unused.
Selects the signal source for OUT2.
0 = source for OUT2 is the output of the P1 divider (default).
1 = source for OUT2 is the input reference (REF or XTAL).
Unused.
Rev. C | Page 28 of 32
AD9552
OUT2 Driver Control (Register 0x34)
Table 26.
Address
0x34
Bit
7
Bit Name
OUT2 drive strength
6
OUT2 power-down
[5:3]
OUT2 mode control
[2:1]
OUT2 CMOS polarity
0
Enable SPI control of OUT2
driver control
Description
Controls the output drive capability of the OUT2 driver.
0 = weak.
1 = strong (default).
Controls power-down functionality of the OUT2 driver.
0 = OUT2 active (default).
1 = OUT2 powered down.
OUT2 driver mode selection.
000 = CMOS, both pins active.
001 = CMOS, positive pin active, negative pin tristate.
010 = CMOS, positive pin tristate, negative pin active.
011 = CMOS, both pins tristate.
100 = LVDS.
101 = LVPECL (default).
110 = not used.
111 = not used.
Selects the polarity of the OUT2 pins in CMOS mode.
00 = positive pin logic is true = 1, false = 0/negative pin logic is true = 0, false = 1 (default).
01 = positive pin logic is true = 1, false = 0/negative pin logic is true = 1, false = 0.
10 = positive pin logic is true = 0, false = 1/negative pin logic is true = 0, false = 1.
11 = positive pin logic is true = 0, false = 1/negative pin logic is true = 1, false = 0.
These bits are ineffective unless Bits[5:3] select CMOS mode.
Controls OUT2 driver functionality.
0 = OUT2 is LVDS or LVPECL, per the OUTSEL pin (Pin 15) (default).
1 = OUT2 functionality defined by Bits[7:1].
Rev. C | Page 29 of 32
AD9552
OUTLINE DIMENSIONS
0.60 MAX
5.00
BSC SQ
0.60 MAX
PIN 1
INDICATOR
0.50
BSC
4.75
BSC SQ
0.50
0.40
0.30
12° MAX
17
16
0.80 MAX
0.65 TYP
0.30
0.23
0.18
3.25
3.10 SQ
2.95
EXPOSED
PAD
(BOTTOM VIEW)
9
8
0.25 MIN
3.50 REF
0.05 MAX
0.02 NOM
SEATING
PLANE
1
0.20 REF
COPLANARITY
0.08
FOR PROPER CONNECTION OF
THE EXPOSED PAD, REFER TO
THE PIN CONFIGURATION AND
FUNCTION DESCRIPTIONS
SECTION OF THIS DATA SHEET.
COMPLIANT TO JEDEC STANDARDS MO-220-VHHD-2
011708-A
TOP
VIEW
1.00
0.85
0.80
PIN 1
INDICATOR
32
25
24
Figure 30. 32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
5 mm × 5 mm Body, Very Thin Quad
(CP-32-2)
Dimensions shown in millimeters
ORDERING GUIDE
Model 1
AD9552BCPZ
AD9552BCPZ-REEL7
AD9552/PCBZ 1
Temperature Range
−40°C to +85°C
−40°C to +85°C
Package Description
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
32-Lead Lead Frame Chip Scale Package [LFCSP_VQ]
Evaluation Board
Z = RoHS Compliant Part.
Rev. C | Page 30 of 32
Package Option
CP-32-2
CP-32-2
AD9552
NOTES
Rev. C | Page 31 of 32
AD9552
NOTES
©2009–2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D07806-0-7/10(C)
Rev. C | Page 32 of 32