AD ADUC7122

Preliminary Technical Data
Precision Analog Microcontroller, 12-Bit
Analog I/O, ARM7TDMI® MCU
ADuC7122
FEATURES
Software-triggered in-circuit reprogrammability
On-chip peripherals
UART, 2 × I2C and SPI serial I/O
32-pin GPIO port
4× general-purpose timers
Wake-up and watchdog timers (WDT)
Power supply monitor
Vectored interrupt controller for FIQ and IRQ
8 Priority levels for each interrupt type
Interrupt on edge or level external pin inputs
Power
Specified for 3 V operation
Active mode: 11 mA at 5 MHz, 40 mA at 41.78 MHz
Packages and temperature range
7 mm × 7mm 108-ball BGA
Fully specified for −10°C to +95°C operation
Tools
Low cost QuickStart™ development system
Full third-party support
Analog I/O
13 external channel, 12-bit, 1 MSPS ADC
2 channels with programmable gain
PGA (1 to 5) input range
IOVDD power monitor channel
On-chip temperature monitor
11 general-purpose inputs
Fully differential and single-ended modes
0 V to VREF analog input range
12 × 12-bit voltage output DACs
On-chip voltage reference: 1.2 V/2.5 V
Buffered output reference sources for use with external
circuits
Microcontroller
ARM7TDMI core, 16-bit/32-bit RISC architecture
JTAG port supports code download and debug
Clocking options
Trimmed on-chip oscillator (±3%)
External watch crystal
External clock source up to 41.78 MHz
41.78 MHz PLL with programmable divider
Memory
126 kB Flash/EE memory, 8 kB SRAM
In-circuit download, JTAG-based debug
APPLICATIONS
Optical networking, industrial control, and automation
systems
Smart sensors, precision instrumentation, base station
systems
FUNCTIONAL BLOCK DIAGRAM
Figure 1.
Rev. PrA
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113
©2010 Analog Devices, Inc. All rights reserved.
ADuC7122
Preliminary Technical Data
TABLE OF CONTENTS
Features .............................................................................................. 1 DAC.............................................................................................. 40 Applications ....................................................................................... 1 LDO (Low Dropout Regulator) ................................................ 42 Functional Block Diagram .............................................................. 1 Oscillator and PLL—Power Control ............................................ 43 Specifications..................................................................................... 3 External Crystal Selection ......................................................... 43 Timing Specifications .................................................................. 7 External Clock Selection ........................................................... 43 Absolute Maximum Ratings.......................................................... 12 Power Control System ............................................................... 44 ESD Caution ................................................................................ 12 MMRs and Keys ......................................................................... 45 Pin Configuration and Function Descriptions ........................... 13 Digital Peripherals .......................................................................... 46 Terminology .................................................................................... 17 PWM General Overview ........................................................... 46 ADC Specifications .................................................................... 17 PWM Convert Start Control .................................................... 48 DAC Specifications..................................................................... 17 General-Purpose I/O ..................................................................... 49 Overview of the ARM7TDMI Core ............................................. 18 UART Serial Interface .................................................................... 52 Thumb Mode (T)........................................................................ 18 Baud Rate Generation ................................................................ 52 Long Multiply (M) ...................................................................... 18 UART Register Definition ......................................................... 52 EmbeddedICE (I) ....................................................................... 18 I C ..................................................................................................... 57 Exceptions ................................................................................... 18 Serial Clock Generation ............................................................ 57 ARM Registers ............................................................................ 18 I2C Bus Addresses ....................................................................... 57 Interrupt Latency ........................................................................ 19 I2C Registers ................................................................................ 58 Memory Organization ................................................................... 20 I2C Common registers ............................................................... 66 Flash/EE Memory ....................................................................... 20 Serial Peripheral Interface ............................................................. 67 SRAM ........................................................................................... 20 SPIMISO (Master In, Slave Out) Pin ....................................... 67 Memory Mapped Registers ....................................................... 20 SPIMOSI (Master Out, Slave In) Pin ....................................... 67 Complete MMR Listing ............................................................. 21 SPICLk (Serial Clock I/O) Pin ................................................. 67 ADC Circuit Overview .................................................................. 25 SPI Chip Select (SPI CS Input) Pin .......................................... 67 ADC Transfer Function ............................................................. 26 Configuring External pins for SPI functionality .................... 67 Typical Operation ....................................................................... 27 SPI Registers ................................................................................ 68 Temperature Sensor ................................................................... 28 Programmable Logic Array (PLA) ............................................... 71 Converter Operation .................................................................. 31 Interrupt System ......................................................................... 73 Driving the Analog Inputs ........................................................ 32 IRQ ............................................................................................... 74 Band Gap Reference ................................................................... 33 Fast Interrupt Request (FIQ) .................................................... 74 Power Supply Monitor ............................................................... 33 Timers .......................................................................................... 80 Nonvolatile Flash/EE Memory ..................................................... 34 Timer0—Lifetime Timer ........................................................... 80 Flash/EE Memory Overview..................................................... 34 Timer1—General-Purpose Timer ........................................... 82 Flash/EE Memory ....................................................................... 34 Timer2—Wake-Up Timer ......................................................... 84 Flash/EE Memory Security ....................................................... 35 Timer3—Watchdog Timer ........................................................ 86 Flash/EE Control Interface........................................................ 35 Timer4—General-Purpose Timer ........................................... 88 Execution Time from SRAM and FLASH/EE ........................ 38 Outline Dimensions ....................................................................... 90 Reset and Remap ........................................................................ 39 Ordering Guide .......................................................................... 90 2
Other Analog Peripherals .............................................................. 40 Rev. PrA | Page 2 of 92
Preliminary Technical Data
ADuC7122
SPECIFICATIONS
AVDD = IOVDD = 3.0 V to 3.6 V, ±5%, VREF = 2.5 V internal reference, fCORE = 41.78 MHz, TA = −10°C to +95°C, unless otherwise noted.
Table 1.
Parameter
ADC CHANNEL SPECIFICATIONS
ADC Power-Up Time
DC Accuracy1, 2
Resolution
Integral Nonlinearity
Min
Max
5
Unit
Bits
LSB
±0.6
±2
±0.5
1
+1..4/−0.99
LSB
LSB
±2
±1
±2
±1
±5
LSB
LSB
LSB
LSB
±5
69
−78
−75
−80
dB
dB
dB
dB
VCM6 ± VREF/2
0 to VREF
AVdd-1.5
0.15
±0.2
20
20
20
0.15
1000
2
11
3
30
0.1
Test Conditions/Comments
Eight acquisition clocks and fADC/2
μs
12
Differential Nonlinearity3, 4
DC Code Distribution
ENDPOINT ERRORS5
Offset Error
Offset Error Match
Gain Error
Gain Error Match
DYNAMIC PERFORMANCE
Signal-to-Noise Ratio (SNR)
Total Harmonic Distortion (THD)
Peak Harmonic or Spurious Noise
Channel-to-Channel Crosstalk
ANALOG INPUT
Input Voltage Ranges
Differential Mode
Single-Ended Mode
Single-Ended Mode
Leakage Current
Input Capacitance
Input Capacitance
PADC0 Input
Full Scale Input Range
Input Leakage at PADC0P4
Resolution
Gain Error4
Gain Drift4
Offset4
Offset Drift4
PADC0P Compliant Range
PADC1 Input
Full Scale Input Range
Input Leakage at PADC1P4
Resolution
Gain Error4
Gain Drift4
Offset4
Offset Drift4
PADC1P Compliant Range
ON-CHIP VOLTAGE REFERENCE
Output Voltage
Accuracy7
Reference Temperature Coefficient4
Typ
1
50
6
60
AVdd-1.2
V
V
V
μA
pF
pF
μA
nA
Bits
%
ppm/°C
nA
pA/°C
V
2.5 V internal reference, not production tested
for PADC0/PADC1 channels
2.5 V internal reference, gauranteed monotonic
ADC input is a dc voltage
Internally unbuffered channels
fIN = 10 kHz sine wave, fSAMPLE = 1 MSPS internally
unbuffered channels
Includes distortion and noise components
Measured on adjacent channels
See Table 35 and Table 36
Buffer bypassed
Buffer enabled
During ADC acquisition buffer bypassed
During ADC acquisition buffer enabled
28.3 kΩ resistor, PGA gain = 3
0.1% accuracy, 5 ppm external resistor for I to V
PGA offset not included
53.5 kΩ resistor, PGA gain = 3
10.6
0.15
700
2
1
50
6
60
AVdd-1.2
μA
nA
Bits
%
ppm/°C
nA
pA/°C
V
±5
30
V
mV
ppm/°C
11
3
30
0.1
0.1% accuracy, 5 ppm external resistor for I to V
PGA offset not included
0.47 μF from VREF to AGND
2.5
10
Rev. PrA | Page 3 of 92
TA = 25°C
ADuC7122
Parameter
Power Supply Rejection Ratio
Output Impedance
Internal VREF Power-On Time
EXTERNAL REFERENCE INPUT
Input Voltage Range
External reference input Leakage
current
DAC CHANNEL SPECIFICATIONS
DC Accuracy8
Resolution
Relative Accuracy
Differential Nonlinearity
Calculated Offset Error
Actual Offset Error
Gain Error9
Gain Error Mismatch
Settling Time
PSRR4
DC
1kHz
10 kHz
100 kHz
OFFSET DRIFT4
GAIN ERROR DRIFT4
SHORT CIRCUIT CURRENT
ANALOG OUTPUTS
Output Range
Preliminary Technical Data
Min
Typ
61
10
1
1.2
Max
AVDD
TBD
Unit
dB
Ω
ms
TA = 25°C
V
μA
RL = 5 kΩ, CL = 100 pF
Buffered
12
±2
±0.2
±2
9
±0.15
0.1
10
±1
±0.8
Bits
LSB
LSB
mV
mV
%
%
μs
Guaranteed monotonic
2.5 V internal reference
Measured at Code 0
% of full scale on DAC0
Buffered
−59
−57
−47
−19
-61
10
10
20
0.1
dB
dB
dB
dB
μV/°C
μV/°C
mA
Buffer on
VREF/AVDD −
0.1
DAC AC CHARACTERISTICS
Slew Rate
Voltage Output Settling Time
Digital-to-Analog Glitch Energy
2.49
10
±20
V/μs
μs
nV-sec
TEMPERATURE SENSOR10
Voltage Output at 25°C
Voltage TC
Accuracy
707
−1.25
±3
mV
mV/°C
°C
2.79
3.07
±2.5
2.36
V
V
%
V
POWER SUPPLY MONITOR (PSM)
IOVDD Trip Point Selection
Power Supply Trip Point Accuracy
POWER-ON RESET
WATCHDOG TIMER (WDT)
Timeout Period
FLASH/EE MEMORY
Endurance11
Data Retention12
DIGITAL INPUTS
Logic 1 Input Current
Logic 0 Input Current
Input Capacitance
Test Conditions/Comments
0
512
10,000
20
±1
−60
MCU in power-down or standby mode before
measurement
Two selectable trip points
Of the selected nominal trip point voltage
sec
cycles
years
±0.2
−40
10
1 LSB change at major carry (where maximum
number of bits simultaneously change in the
DACxDAT register)
μA
μA
pF
Rev. PrA | Page 4 of 92
TJ = 85°C
All digital inputs excluding XCLKI and XTALO
VIH = VDD or VIH = 5 V
VIL = 0 V; except TDI
Preliminary Technical Data
Parameter
LOGIC INPUTS4
VINL, Input Low Voltage4
VINH, Input High Voltage4
LOGIC OUTPUTS
VOH, Output High Voltage
VOL, Output Low Voltage13
CRYSTAL INPUTS XTALI and XTALO
Logic Inputs, XTALI Only
VINL, Input Low Voltage
VINH, Input High Voltage
XTALI Input Capacitance
XTALO Output Capacitance
INTERNAL OSCILLATOR
MCU CLOCK RATE
From 32 kHz Internal Oscillator
From 32 kHz External Crystal
Using an External Clock
START-UP TIME
At Power-On
From Pause/Nap Mode
From Sleep Mode
From Stop Mode
PROGRAMMABLE LOGIC ARRAY (PLA)
Pin Propagation Delay
Element Propagation Delay
POWER REQUIREMENTS14, 15
Power Supply Voltage Range
AVDD to AGND and IOVDD to IOGND
Analog Power Supply Currents
AVDD Current
Digital Power Supply Current
IOVDD Current in Normal Mode
IOVDD Current in Pause Mode4
IOVDD Current in Sleep Mode4
Additional Power Supply Currents
ADC
DAC
Min
ADuC7122
Typ
Max
Unit
0.8
V
V
2.0
2.4
0.4
V
V
±3
V
V
pF
pF
kHz
%
41.78
kHz
MHz
MHz
1.1
1.7
20
20
32.768
326
41.78
0.05
70
24
3.06
1.58
1.7
ms
ns
μs
ms
ms
12
2.5
ns
ns
2.7
3.6
Test Conditions/Comments
All logic inputs excluding XTALI
All digital outputs excluding XTALO
ISOURCE = 1.6 mA
ISINK = 1.6 mA
CD = 7
CD = 0
TA = 95°C
Core clock = 41.78 MHz
CD = 0
CD = 7
From input pin to output pin
V
200
μA
ADC in idle mode
7
11
30
25
100
mA
mA
mA
mA
μA
Code executing from Flash/EE
CD = 7
CD = 3
CD = 0 (41.78 MHz clock)
CD = 0 (41.78 MHz clock)
TA = 85°C
mA
mA
μA
At 1 MSPS
At 62.5 kSPS
Per DAC
2.7
0.7
250
40
Rev. PrA | Page 5 of 92
ADuC7122
Parameter
ESD TESTS
HBM Passed Up to
FCIDM Passed Up to
Preliminary Technical Data
Min
Typ
Max
Unit
4
0.5
kV
kV
1
Test Conditions/Comments
2.5 V reference, TA = 25°C
All ADC channel specifications are guaranteed during normal MicroConverter core operation.
Apply to all ADC input channels.
Measured using the factory-set default values in the ADC offset register (ADCOF) and gain coefficient register (ADCGN); see the the Calibration section.
4
Not production tested but supported by design and/or characterization data on production release.
5
Measured using the factory-set default values in ADCOF and ADCGN with an external AD845 op amp as an input buffer stage as shown in Figure 22. Based on external ADC
system components, the user may need to execute a system calibration to remove external endpoint errors and achieve these specifications (see the ADC Circuit
Overview).
6
The input signal can be centered on any dc common-mode voltage (VCM) as long as this value is within the ADC voltage input range specified.
7
VREF calibration and trimming are performed with core operating in normal mode CD = 0, ADC on, and all DACs on. VREF accuracy may vary under other operating
conditions.
8
DAC linearity is calculated using a reduced code range of 100 to 3995.
9
DAC gain error is calculated using a reduced code range of 100 to internal 2.5 V VREF.
10
Die temperature.
11
Endurance is qualified as per JEDEC Standard 22 Method A117 and measured at −40°C, +25°C, +85°C, and +125°C.
12
Retention lifetime equivalent at junction temperature (TJ) = 85°C as per JEDEC Standard 22 Method A117. Retention lifetime derates with junction temperature.
13
Test carried out with a maximum of eight I/Os set to a low output level.
14
Power supply current consumption is measured in normal, pause, and sleep modes under the following conditions: normal mode with 3.6 V supply, pause mode with
3.6 V supply, and sleep mode with 3.6 V supply.
15
IOVDD power supply current decreases typically by 2 mA during a Flash/EE erase cycle.
2
3
Rev. PrA | Page 6 of 92
Preliminary Technical Data
ADuC7122
TIMING SPECIFICATIONS
Table 2. I2C Timing in Fast Mode (400 kHz)
Parameter
tL
tH
tSHD
tDSU
tDHD
tRSU
tPSU
tBUF
tR
tF
Description
SCLOCK low pulse width
SCLOCK high pulse width
Start condition hold time
Data setup time
Data hold time
Setup time for repeated start
Stop condition setup time
Bus-free time between a stop condition and a start condition
Rise time for both SCLx and SDAx
Fall time for both SCLx and SDAx
Min
200
100
300
100
0
100
100
1.3
Slave
Max
Master
Typ
1360
1140
740
400
800
300
300
200
Unit
ns
ns
ns
ns
ns
ns
ns
μs
ns
ns
Table 3. I2C Timing in Standard Mode (100 kHz)
Parameter
tL
tH
tSHD
tDSU
tDHD
tRSU
tPSU
tBUF
tR
tF
Description
SCLOCK low pulse width
SCLOCK high pulse width
Start condition hold time
Data setup time
Data hold time
Setup time for repeated start
Stop condition setup time
Bus-free time between a stop condition and a start condition
Rise time for both SCLx and SDAx
Fall time for both SCLx and SDAx
tBUF
Slave
Max
Min
4.7
4.0
4.0
250
0
4.7
4.0
4.7
3.45
1
300
tSUP
tR
MSB
LSB
tDSU
tSHD
P
S
tF
tDHD
2–7
8
tL
tR
tRSU
tH
1
SCLK (I)
MSB
tDSU
tDHD
tPSU
ACK
9
tSUP
1
S(R)
REPEATED
START
STOP
START
CONDITION CONDITION
Figure 2. I2C-Compatible Interface Timing
Rev. PrA | Page 7 of 92
tF
04955-054
SDATA (I/O)
Unit
μs
ns
μs
ns
μs
μs
μs
μs
μs
ns
ADuC7122
Preliminary Technical Data
Table 4. SPI Master Mode Timing (Phase Mode = 1)
Parameter
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
Min
Typ
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
Max
25
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
SCLOCK
(POLARITY = 0)
tSH
tSL
tSR
SCLOCK
(POLARITY = 1)
tDAV
tDF
MOSI
MISO
tDR
MSB
MSB IN
tSF
BITS 6 TO 1
BITS 6 TO 1
tDSU
tDHD
Figure 3. SPI Master Mode Timing (PHASE Mode = 1)
Rev. PrA | Page 8 of 92
LSB
LSB IN
04955-055
1
Description
SCLOCK low pulse width
SCLOCK high pulse width
Data output valid after SCLOCK edge
Data input setup time before SCLOCK edge1
Data input hold time after SCLOCK edge
Data output fall time
Data output rise time
SCLOCK rise time
SCLOCK fall time
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
Preliminary Technical Data
ADuC7122
Table 5. SPI Master Mode Timing (Phase Mode = 0)
Parameter
tSL
tSH
tDAV
tDOSU
tDSU
tDHD
tDF
tDR
tSR
tSF
Min
Typ
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
25
75
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
SCLOCK
(POLARITY = 0)
tSH
tSL
tSR
tSF
SCLOCK
(POLARITY = 1)
tDAV
tDOSU
MOSI
MISO
tDF
MSB
MSB IN
tDR
BITS 6 TO 1
BITS 6 TO 1
LSB
LSB IN
tDSU
04955-056
1
Description
SCLOCK low pulse width
SCLOCK high pulse width
Data output valid after SCLOCK edge
Data output setup before SCLOCK edge
Data input setup time before SCLOCK edge1
Data input hold time after SCLOCK edge
Data output fall time
Data output rise time
SCLOCK rise time
SCLOCK fall time
tDHD
Figure 4. SPI Master Mode Timing (PHASE Mode = 0)
Rev. PrA | Page 9 of 92
ADuC7122
Preliminary Technical Data
Table 6. SPI Slave Mode Timing (Phase Mode = 1)
Parameter
tCS
Description
CS to SCLOCK edge
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
tSFS
SCLOCK low pulse width1
SCLOCK high pulse width1
Data output valid after SCLOCK edge
Data input setup time before SCLOCK edge
Data input hold time after SCLOCK edge
Data output fall time
Data output rise time
SCLOCK rise time
SCLOCK fall time
CS high after SCLOCK edge
Typ
Max
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
25
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
0
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
CS
tSFS
tCS
SCLOCK
(POLARITY = 0)
tSH
tSL
tSR
tSF
SCLOCK
(POLARITY = 1)
tDAV
MISO
tDF
MSB
MOSI
MSB IN
tDR
BITS 6 TO 1
BITS 6 TO 1
tDSU
tDHD
Figure 5. SPI Slave Mode Timing (PHASE Mode = 1)
Rev. PrA | Page 10 of 92
LSB
LSB IN
04955-057
1
Min
200
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Preliminary Technical Data
ADuC7122
Table 7. SPI Slave Mode Timing (Phase Mode = 0)
Parameter
tCS
Description
CS to SCLOCK edge
tSL
tSH
tDAV
tDSU
tDHD
tDF
tDR
tSR
tSF
tDOCS
tSFS
SCLOCK low pulse width1
SCLOCK high pulse width1
Data output valid after SCLOCK edge
Data input setup time before SCLOCK edge1
Data input hold time after SCLOCK edge1
Data output fall time
Data output rise time
SCLOCK rise time
SCLOCK fall time
Data output valid after CS edge
CS high after SCLOCK edge
Typ
Max
(SPIDIV + 1) × tUCLK
(SPIDIV + 1) × tUCLK
25
1 × tUCLK
2 × tUCLK
5
5
5
5
12.5
12.5
12.5
12.5
25
0
tUCLK = 23.9 ns. It corresponds to the 41.78 MHz internal clock from the PLL before the clock divider.
CS
tCS
tSFS
SCLOCK
(POLARITY = 0)
tSH
tSL
tSF
tSR
SCLOCK
(POLARITY = 1)
tDAV
tDOCS
tDF
MISO
MOSI
MSB
MSB IN
tDR
BITS 6 TO 1
BITS 6 TO 1
LSB
LSB IN
tDSU
tDHD
Figure 6. SPI Slave Mode Timing (PHASE Mode = 0)
Rev. PrA | Page 11 of 92
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
04955-058
1
Min
200
ADuC7122
Preliminary Technical Data
ABSOLUTE MAXIMUM RATINGS
AGND = REFGND = DACGND = GNDREF, TA = 25°C,
unless otherwise noted.
Table 8.
Parameter
AVDD to IOVDD
AGND to DGND
IOVDD to IOGND, AVDD to AGND
Digital Input Voltage to IOGND
Digital Output Voltage to IOGND
VREF_2.5 and VREF_1.2 to AGND
Analog Inputs to AGND
Analog Outputs to AGND
Operating Temperature Range, Industrial
Storage Temperature Range
Junction Temperature
θJA Thermal Impedance
108-Ball CSP_BGA
Peak Solder Reflow Temperature
SnPb Assemblies (10 sec to 30 sec)
RoHS-Compliant Assemblies
(20 sec to 40 sec)
Rating
−0.3 V to +0.3 V
−0.3 V to +0.3 V
−0.3 V to +6 V
−0.3 V to +5.3 V
−0.3 V to IOVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−0.3 V to AVDD + 0.3 V
−40°C to +125°C
–65°C to +150°C
150°C
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Only one absolute maximum rating can be applied at any one time.
ESD CAUTION
40°C/W
240°C
260°C
Rev. PrA | Page 12 of 92
Preliminary Technical Data
ADuC7122
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
12
11
10
9
8
7
6
5
4
3
2
1
A1
corner
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
n.c.
A
n.c.
n.c.
AGND
AGND
n.c.
REG_PWR AGND
n.c.
n.c.
P1.6
P1.7
n.c.
B
/RST
P3.1
TDI/
P1.2
P2.7
n.c.
n.c.
n.c.
P3.0
P0.2
P1.0
P2.6
C
P3.6
P0.0
TDO/
P1.3
P0.3
P1.1
P3.2
D
P3.7
P0.1
TMS
P0.4
P3.4
P3.3
E
DGND
P2.0
TCK
P0.5
P3.5
DGND
F
LVDD
P2.1
P0_7
P0.6
XTALO
LVDD
G
IOVDD
P2.2
P2.4
P1.4
XTALI
IOVDD
H
IOGND
P2.3
P2.5
P1.5
DAC2
IOGND
J
DAC11
DAC10
DAC9
ADC1
ADC4
DAC1
DAC0
K
ADC3
DAC5
DAC3
AVDD
L
PADC0N ADC2
ADC5
DAC4
AGND
M
ADC9
n.c.
ADC10/
BUF_
BUF_
AINCM
VREF2
VREF1
PADC1P
PADC0P Vref_1.2
AVDD
DAC7
DAC8
ADC8
Vref_2.5
AGND
DAC6
ADC6
AIN7
PADC1N AVDD
AGND
ADC0
Figure 7. Pin Configuration
Table 9. Pin Function Descriptions
Pin No.
C12
D11
Mnemonic
RST
P0.0/SCL1/PLAI[5]
Type1
I
I/O
E11
P0.1/SDA1/PLAI[4]
I/O
C3
P0.2/SPICLK/PLAO[13]
I/O
D3
P0.3/SPIMISO/PLAO[12]/SYNC
I/O
E3
P0.4/SPIMOSI/PLAI[11]/TRIP
I/O
Description
Reset Input (Active Low).
General-Purpose Input and Output Port 0.0 (P0.0).
I2C Interface SCLOCK for I2C0 (SCL1).
Input to PLA Element 5 (PLAI[5]).
General-Purpose Input and Output Port 0.1 (P0.1).
I2C Interface SDATA for I2C0 (SDA1).
Input to PLA Element 4 (PLAI[4]).
General-Purpose Input and Output Port 0.2 (P0.2).
SPI Clock (SPICLK).
Output of PLA Element 13 (PLAO[13]).
General-Purpose Input and Output Port 0.3 (P0.3).
SPI Master Input, Slave Output (SPIMISO).
Output of PLA Element 12 (PLAO[12]).
TBD (SYNC).
General-Purpose Input and Output Port 0.4 (P0.4).
SPI Master Out Slave Input (SPIMOSI).
Input to PLA Element 11 (PLAI[11]).
TBD (TRIP).
Rev. PrA | Page 13 of 92
ADuC7122
Preliminary Technical Data
Pin No.
F3
Mnemonic
P0.5/SPICS/PLAI[10]/CONVST
Type1
I/O
G3
P0.6/MRST/PLAI[2]
I/O
G10
P0.7/TRST/PLAI[3]
I/O
C2
P1.0/SIN/SCL2/PLAI[7]
I/O
D2
P1.1/SOUT/SDA2/PLAI[6]
I/O
H3
P1.4/PWM1/PLAI[8]/XCLK
I/O
J3
P1.5/PWM2/PLAI[9]
I/O
B3
P1.6/PLAO[5]
I/O
B2
P1.7/PLAO[4]
I/O
F11
P2.0/IRQ0/PLAI[13]
I/O
G11
P2.1/IRQ1/PLAI[12]
I/O
H11
P2.2/PLAI[1]
I/O
J11
P2.3/IRQ2/PLAI[14]
I/O
H10
P2.4/PWM5/PLAO[7]
I/O
J10
P2.5/PWM6/PLAO[6]
I/O
C1
P2.6/IRQ3/PLAI[15]
I/O
C9
P2.7/PLAI[0]
I/O
C4
P3.0/PLAO[0]
I/O
C11
P3.1/PLAO[1]
I/O
D1
P3.2/IRQ4/PWM3/PLAO[2]
I/O
Description
General-Purpose Input and Output Port 0.5 (P0.5).
SPI Slave Select Input (SPICS).
Input to PLA Element 10 (PLAI[10]).
TBD (CONVST).
General-Purpose Input and Output Port 0.6 (P0.6).
Power-On Reset Output (MRST).
Input to PLA Element 2 (PLAI[2])
General-Purpose Input and Output Port 0.7 (P0.7).
JTAG Test Port Input, Test Reset (TRST). Debug and download access.
Input to PLA Element 3 (PLAI[3]).
General-Purpose Input and Output Port 1.0 (P1.0).
Serial Input, Receive Data (RxD), UART (SIN)
I2C Interface SCLOCK for I2C1 (SCL2).
Input to PLA Element 7 (PLAI[7]).
General-Purpose Input and Output Port 1.1 (P1.1).
Serial Output, Transmit Data (TxD), UART (SOUT)
I2C Interface SDATA for I2C1 (SDA2).
Input to PLA Element 6 (PLAI[6]).
General-Purpose Input and Output Port 1.4 (P1.4).
PWM1 Output (PWM1).
Input to PLA Element 8 (PLAI[8]).
General-Purpose Input and Output Port 1.5 (P1.5).
PWM2 Output (PWM2).
Input to PLA Element 9 (PLAI[9]).
General-Purpose Input and Output Port 1.6 (P1.6).
Output of PLA Element 5 (PLAO[5]).
General-Purpose Input and Output Port 1.7 (P1.7).
Output of PLA Element 4 (PLAO[4]).
General-Purpose Input and Output Port 2.0 (P2.0).
External Interrupt Request 0 (IRQ0).
Input to PLA Element 13 (PLAI[13]).
General-Purpose Input and Output Port 2.1 (P2.1).
External Interrupt Request 1 (IRQ0).
Input to PLA Element 12 (PLAI[12]).
General-Purpose Input and Output Port 2.2 (P2.2).
Input to PLA Element 1 (PLAI[1]).
General-Purpose Input and Output Port 2.3 (P2.3).
External Interrupt Request 2 (IRQ2).
Input to PLA Element 14 (PLAI[14]).
General-Purpose Input and Output Port 2.4 (P2.4).
PWM5 Output (PWM5).
Output of PLA Element 7 (PLAO[7]).
General-Purpose Input and Output Port 2.5 (P2.5).
PWM6 Output (PWM6).
Output of PLA Element 6 (PLAO[6]).
General-Purpose Input and Output Port 2.6 (P2.6).
External Interrupt Request 3 (IRQ3).
Input to PLA Element 15 (PLAI[15]).
General-Purpose Input and Output Port 2.7 (P2.7).
Input to PLA Element 0 (PLAI[0]).
General-Purpose Input and Output Port 3.0 (P3.0).
Output of PLA Element 0 (PLAO[0]).
General-Purpose Input and Output Port 3.1 (P3.1).
Output of PLA Element 1 (PLAO[1]).
General-Purpose Input and Output Port 3.2 (P3.2).
External Interrupt Request 4 (IRQ4).
Rev. PrA | Page 14 of 92
Preliminary Technical Data
Pin No.
Mnemonic
Type1
E1
P3.3/IRQ5/PWM4/PLAO[3]
I/O
E2
P3.4/PLAO[8]
I/O
F2
P3.5/PLAO[9]
I/O
D12
P3.6/PLAO[10]
I/O
E12
P3.7/PLAO[11]/BM
I/O
L8
VREF_2.5
AI/O
L5
VREF_1.2
AI/O
B8
K6
K7
L6
M5
L7
M8
K5
K4
M4
L4
K3
M3
M10
M9
L9
K9
K8
NC
BUF_VREF1
BUF_VREF2
PADC0P
PADC0N
PADC1P
PADC1N
ADC0
ADC1
ADC2
ADC3
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10/AINCM
NC
AO
AO
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
AI
K1
K2
J2
L2
M2
L3
M11
L11
L10
K10
K11
K12
B5
C6
A6
DAC0
DAC1
DAC2
DAC3
DAC4
DAC5
DAC6
DAC7
DAC8
DAC9
DAC10
DAC11
NC
NC
NC
AO
AO
AO
AO
AO
AO
AO
AO
AO
AO
AO
AO
NC
NC
NC
ADuC7122
Description
PWM3 Output (PWM3).
Output of PLA Element 2 (PLAO[2]).
General-Purpose Input and Output Port 3.3 (P3.3).
External Interrupt Request 5 (IRQ5).
PWM4 Output (PWM4).
Output of PLA Element 3 (PLAO[3]).
General-Purpose Input and Output Port 3.4 (P3.4).
Output of PLA Element 8 (PLAO[8]).
General-Purpose Input and Output Port 3.5 (P3.5).
Output of PLA Element 9 (PLAO[9]).
General-Purpose Input and Output Port 3.6 (P3.6).
Output of PLA Element 10 (PLAO[10]).
General-Purpose Input and Output Port 3.7 (P3.7).
Output of PLA Element 11 (PLAO[11]).
Boot Mode (BM).
If this pin is low and Address 0x00014 of flash is 0xFFFFFFFF, then the part enters I2C
download after the next rest sequence.
2.5 V Reference Output, External 2.5 V Reference Input. Can be used to drive the anode
of a photo diode
1.2 V Reference Output, External 1.2 V Reference Input. Cannot be used to source
current externally.
No connect.
Buffered 2.5 V Bias. Maximum load = 1.2 mA.
Buffered 2.5 V. Maximum load = 1.2 mA.
PADC0 Positive Input Channel. PGA-based ADC input channel.
PADC0 Negative Input Channel. PGA-based ADC input channel.
PADC1 Positive Input Channel. PGA-based ADC input channel.
PADC1 Negative Input Channel. PGA-based ADC input channel.
Single-Ended or Differential Analog Input 0/Thermistor Positive Input 0.
Single-Ended or Differential Analog Input 1/Thermistor Ground Input 0
Single-Ended or Differential Analog Input 2/Thermistor Positive Input 1.
Single-Ended or Differential Analog Input 3/Thermistor Ground Input 1.
Single-Ended Analog Input 4/Positive Differential Input 0.
Single-Ended Analog Input 5/Negative Differential Input 0.
Single-Ended Analog Input 6/Positive Differential Input 1.
Single-Ended Analog Input 7/Negative Differential Input 1.
Single-Ended Analog Input 8/Positive Differential Input 2.
Single-Ended Analog Input 9/Negative Differential Input 2.
Single-Ended or Differential Analog Input 10 (ADC10).
Common Mode for Pseudo Differential Input (AINCM).
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
12-Bit DAC Output.
No connect.
No connect.
No connect.
Rev. PrA | Page 15 of 92
ADuC7122
Preliminary Technical Data
Pin No.
A8
A7
C8
A5
C5
B4
A4
A1
A3
A2
B1
A12
A9
A11
A10
B12
B11
B10
B9
M1
M6
L1
M7
M12
B6
L12
C7
B7
Mnemonic
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
AGND
AGND
AGND
AGND
AVDD
AVDD
AGND
AGND
AVDD
NC
REG_PWR
Type1
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
NC
S
S
S
S
S
S
S
S
S
NC
S
G1
LVDD
S
G12
LVDD
S
F1
F12
H1
J1
H12
J12
G2
DGND
DGND
IOVDD
IOGND
IOVDD
IOGND
XTALO
S
S
S
S
S
S
DO
H2
XTALI
DI
D10
TDO/P1.3/PLAO[14]
DO
C10
TDI/P1.2/PLAO[15]
DI
F10
E10
TCK
TMS
DI
DI
1
Description
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
No connect.
Analog Ground.
Analog Ground.
Analog Ground.
Analog Ground.
Analog Supply (3.3 V).
Analog Supply (3.3 V).
Analog Ground.
Analog Ground.
Analog Supply (3.3 V).
No connect.
Output of 2.5 V on-chip Regulator. A 470 nF capacitor to DGND must be connected to
this pin.
Output of 2.6 V on-chip LDO regulator. A 470 nF capacitor to DGND must be
connected to this pin.
Output of 2.6 V on-chip LDO regulator. A 470 nF capacitor to DGND must be
connected to this pin.
Digital ground.
Digital ground.
3.3V GPIO Supply.
3.3V GPIO Ground.
3.3V GPIO Supply.
3.3V GPIO Ground.
Output from the Crystal Oscillator Inverter. If an external crystal is not being used, this
pin can be left unconnected.
Input to the Crystal Oscillator Inverter and Input to the Internal Clock Generator
Circuits. If an external crystal is not being used, this pin should be connected to the
DGND system ground.
JTAG Test Port Output, Test Data Out (TDO). Debug and download access.
General-Purpose Input and Output Port 1.3 (P1.3).
JTAG Test Port Input, Test Data In (TDI). Debug and download access.
General-Purpose Input and Output Port 1.2 (P1.2).
JTAG Test Port Input, Test Clock. Debug and download access.
JTAG Test Port Input, Test Mode Select. Debug and download access.
I = input, I/O = input/output, AI/O = analog input/output, NC = no connect, AO = analog output, AI = analog input, DI = digital input, DO = digital output, S = supply.
Rev. PrA | Page 16 of 92
Preliminary Technical Data
ADuC7122
TERMINOLOGY
ADC SPECIFICATIONS
Integral Nonlinearity (INL)
The maximum deviation of any code from a straight line
passing through the endpoints of the ADC transfer function.
The endpoints of the transfer function are zero scale, a point
½ LSB below the first code transition, and full scale, a point
½ LSB above the last code transition.
Differential Nonlinearity (DNL)
The difference between the measured and the ideal 1 LSB
change between any two adjacent codes in the ADC.
The ratio is dependent upon the number of quantization levels
in the digitization process; the more levels there are, the smaller
the quantization noise becomes.
The theoretical signal-to-(noise + distortion) ratio for an ideal
N-bit converter with a sine wave input is given by
Signal to (Noise + Distortion) = (6.02 N + 1.76) dB
Thus, for a 12-bit converter, this is 74 dB.
Total Harmonic Distortion
The ratio of the rms sum of the harmonics to the fundamental.
DAC SPECIFICATIONS
Offset Error
The deviation of the first code transition (0000…000) to
(0000…001) from the ideal, that is, ½ LSB.
Gain Error
The deviation of the last code transition from the ideal AIN
voltage (full scale − 1.5 LSB) after the offset error has been
adjusted out.
Signal-to-(Noise + Distortion) Ratio
The measured ratio of signal to (noise + distortion) at the
output of the ADC. The signal is the rms amplitude of the
fundamental. Noise is the rms sum of all nonfundamental
signals up to half the sampling frequency (fS/2), excluding dc.
Relative Accuracy
Otherwise known as endpoint linearity, relative accuracy is a
measure of the maximum deviation from a straight line passing
through the endpoints of the DAC transfer function. It is
measured after adjusting for zero error and full-scale error.
Voltage Output Settling Time
The amount of time it takes the output to settle to within a
1 LSB level for a full-scale input change.
Rev. PrA | Page 17 of 92
ADuC7122
Preliminary Technical Data
OVERVIEW OF THE ARM7TDMI CORE
The ARM7® core is a 32-bit reduced instruction set computer
(RISC). It uses a single 32-bit bus for instruction and data. The
length of the data can be eight bits, 16 bits, or 32 bits. The
length of the instruction word is 32 bits.
The ARM7TDMI is an ARM7 core with four additional
features:
T support for the thumb (16-bit) instruction set
D support for debug
M support for long multiplications
I includes the EmbeddedICE module to support embedded
system debugging
THUMB MODE (T)
An ARM instruction is 32 bits long. The ARM7TDMI
processor supports a second instruction set that has been
compressed into 16 bits, called the thumb instruction set. Faster
execution from 16-bit memory and greater code density can
usually be achieved by using the thumb instruction set instead
of the ARM instruction set, which makes the ARM7TDMI core
particularly suitable for embedded applications.
However, the thumb mode has two limitations:


Thumb code typically requires more instructions for the
same job. As a result, ARM code is usually best for
maximizing the performance of time-critical code.
The thumb instruction set does not include some of the
instructions needed for exception handling, which
automatically switches the core to ARM code for exception
handling.
See the ARM7TDMI user guide for details on the core
architecture, the programming model, and both the ARM
and ARM thumb instruction sets.
LONG MULTIPLY (M)
The ARM7TDMI instruction set includes four extra instructions that perform 32-bit by 32-bit multiplication with a 64-bit
result, and 32-bit by 32-bit multiplication-accumulation (MAC)
with a 64-bit result. These results are achieved in fewer cycles
than required on a standard ARM7 core.
ARM supports five types of exceptions and a privileged
processing mode for each type. The five types of exceptions are:





Normal interrupt or IRQ. This is provided to service
general-purpose interrupt handling of internal and
external events.
Fast interrupt or FIQ. This is provided to service data
transfers or communication channels with low latency. FIQ
has priority over IRQ.
Memory abort.
Attempted execution of an undefined instruction.
Software interrupt instruction (SWI). This can be used to
make a call to an operating system.
Typically, the programmer defines interrupt as IRQ, but for
higher priority interrupt, that is, faster response time, the
programmer can define interrupt as FIQ.
ARM REGISTERS
ARM7TDMI has a total of 37 registers: 31 general-purpose
registers and six status registers. Each operating mode has
dedicated banked registers.
When writing user-level programs, 15 general-purpose 32-bit
registers (R0 to R14), the program counter (R15) and the
current program status register (CPSR) are usable. The
remaining registers are only used for system-level programming
and exception handling.
When an exception occurs, some of the standard registers are
replaced with registers specific to the exception mode. All exception modes have replacement banked registers for the stack
pointer (R13) and the link register (R14), as represented in
Figure 8. The fast interrupt mode has more registers (R8 to R12)
for fast interrupt processing. This means the interrupt processing
can begin without the need to save or restore these registers,
and thus save critical time in the interrupt handling process.
R0
USABLE IN USER MODE
R1
SYSTEM MODES ONLY
R2
R3
R4
EmbeddedICE (I)
R5
EmbeddedICE provides integrated on-chip support for the core.
The EmbeddedICE module contains the breakpoint and watchpoint registers that allow code to be halted for debugging purposes.
These registers are controlled through the JTAG test port.
R7
R6
R8
R9
R10
R11
R12
When a breakpoint or watchpoint is encountered, the processor
halts and enters a debug state. Once in a debug state, the
processor registers can be inspected as well as the Flash/EE,
SRAM, and memory mapped registers.
R13
R14
R8_FIQ
R9_FIQ
R10_FIQ
R11_FIQ
R12_FIQ
R13_FIQ
R14_FIQ
R13_SVC
R14_SVC
R13_ABT
R14_ABT
R13_IRQ
R14_IRQ
R13_UND
R14_UND
R15 (PC)
CPSR
USER MODE
SPSR_FIQ
FIQ
MODE
SPSR_SVC
SVC
MODE
SPSR_ABT
ABORT
MODE
SPSR_IRQ
IRQ
MODE
Figure 8. Register Organization
Rev. PrA | Page 18 of 92
SPSR_UND
UNDEFINED
MODE
04955-007




EXCEPTIONS
Preliminary Technical Data
ADuC7122
More information relative to the programmer’s model and the
ARM7TDMI core architecture can be found in the following
materials from ARM:


DDI 0029G, ARM7TDMI Technical Reference Manual
DDI 0100, ARM Architecture Reference Manual
INTERRUPT LATENCY
The worst-case latency for a fast interrupt request (FIQ)
consists of the following:




The longest time the request can take to pass through the
synchronizer
The time for the longest instruction to complete (the
longest instruction is an LDM) that loads all the registers
including the PC
The time for the data abort entry
The time for FIQ entry
At the end of this time, the ARM7TDMI executes the instruction at 0x1C (FIQ interrupt vector address). The maximum
total time is 50 processor cycles, which is just under 1.2 μs in a
system using a continuous 41.78 MHz processor clock.
The maximum interrupt request (IRQ) latency calculation is
similar, but must allow for the fact that FIQ has higher priority
and can delay entry into the IRQ handling routine for an
arbitrary length of time. This time can be reduced to 42 cycles if
the LDM command is not used. Some compilers have an option
to compile without using this command. Another option is to run
the part in thumb mode where the time is reduced to 22 cycles.
The minimum latency for FIQ or IRQ interrupts is a total of
five cycles, which consist of the shortest time the request can
take through the synchronizer, plus the time to enter the
exception mode.
Note that the ARM7TDMI always runs in ARM (32-bit) mode
when in privileged modes, for example, when executing
interrupt service routines.
Rev. PrA | Page 19 of 92
ADuC7122
Preliminary Technical Data
MEMORY ORGANIZATION
The ADuC7122 incorporates three separate blocks of memory:
8 kB of SRAM and two 64 kB of on-chip Flash/EE memory.
There are 126 kB of on-chip Flash/EE memory available to the
user, and the remaining 2 kB are reserved for the factoryconfigured boot page. These two blocks are mapped as shown
in Figure 9.
FLASH/EE MEMORY
Note that by default, after a reset, the Flash/EE memory is
mirrored at Address 0x00000000. It is possible to remap the
SRAM at Address 0x00000000 by clearing Bit 0 of the REMAP
MMR. This remap function is described in more detail in the
Flash/EE memory chapter.
The lower 64 kB memory block is organized in a similar
manner. It is arranged in 32 k × 16 bits. All of this is available as
user space.
The 128 kB of Flash/EE are organized as two banks of 32 k ×
16 bits. In the upper memory block, 31 k × 16 bits are user
space and 1 k × 16 bits is reserved for the factory-configured
boot page. The page size of this Flash/EE memory is 512
bytes.
SRAM
The 126 kB of Flash/EE are available to the user as code and
non-volatile data memory. There is no distinction between data
and program as ARM code shares the same space. The real width
of the Flash/EE memory is 16 bits, meaning that in ARM mode
(32-bit instruction), two accesses to the Flash/EE are necessary
for each instruction fetch. Therefore, it is recommended that
Thumb mode be used when executing from Flash/EE memory
for optimum access speed. The maximum access speed for the
Flash/EE memory is 41.78 MHz in Thumb mode and 20.89 MHz
in full ARM mode (see the Execution Time from SRAM and
FLASH/EE section).
RESERVED
SRAM
0xFFFFFFFF
MMRs
0xFFFF0000
RESERVED
0x0009F800
FLASH/EE
0x00080000
RESERVED
0x00041FFF
0x00040000
0x0001FFFF
0x00000000
The 8 kB of SRAM are available to the user, organized as 2 k ×
32 bits, that is, 2 k words. ARM code can run directly from SRAM
at 41.78 MHz, given that the SRAM array is configured as a
32-bit wide memory array (see the Execution Time from SRAM
and FLASH/EE section).
06020-025
REMAPPABLE MEMORY SPACE
(FLASH/EE OR SRAM)
Figure 9. Physical Memory Map
Memory Access
The ARM7 core sees memory as a linear array of 232 byte
location where the different blocks of memory are mapped as
outlined in Figure 9.
The ADuC7122 memory organization is configured in little
endian format: the least significant byte is located in the lowest
byte address and the most significant byte in the highest byte
address.
BIT 31
BIT 0
BYTE 3
.
.
.
BYTE 2
.
.
.
BYTE 1
.
.
.
BYTE 0
.
.
.
B
A
9
8
7
6
5
4
0x00000004
3
2
1
0
0x00000000
32 BITS
Figure 10. Little Endian Format
06020-026
0xFFFFFFFF
MEMORY MAPPED REGISTERS
The memory mapped register (MMR) space is mapped into the
upper two pages of the memory array and accessed by indirect
addressing through the ARM7 banked registers.
The MMR space provides an interface between the CPU and
all on-chip peripherals. All registers except the core registers
reside in the MMR area. All shaded locations shown in Figure 11
are unoccupied or reserved locations and should not be accessed
by user software. Table 10 to Table 26 show a full MMR
memory map.
The access time reading or writing a MMR depends on the
advanced microcontroller bus architecture (AMBA) bus used to
access the peripheral. The processor has two AMBA buses:
advanced high performance bus (AHB) used for system
modules, and advanced peripheral bus (APB) used for lower
performance peripheral. Access to the AHB is one cycle, and
access to the APB is two cycles. All peripherals on the
ADuC7122 are on the APB except the Flash/EE memory and
the GPIOs.
Rev. PrA | Page 20 of 92
Preliminary Technical Data
ADuC7122
Table 10. IRQ Base Address = 0xFFFF0000
Address
0x0000
0x0004
0x0008
0x000C
0x0010
0x0014
0x001C
0x0020
0x0024
0x0028
0x002C
0x0030
0x0034
0x0038
0x003C
0x0100
0x0104
0x0108
0x010C
0x011C
0x013C
Name
IRQSTA
IRQSIG
IRQEN
IRQCLR
SWICFG
IRQBASE
IRQVEC
IRQP0
IRQP1
IRQP2
IRQP3
IRQCONN
IRQCONE
IRQCLRE
IRQSTAN
FIQSTA
FIQSIG
FIQEN
FIQCLR
FIQVEC
FIQSTAN
Byte
4
4
4
4
4
4
4
4
4
4
4
1
1
1
1
4
4
4
4
4
1
Access Type
R
R
R/W
W
W
R/W
R
R/W
R/W
R/W
R/W
R/W
R/W
W
R/W
R
R
R/W
W
R
R/W
Cycle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Table 11. System Control Base Address = 0xFFFF0200
Address
0x0220
0x0230
0x0234
Figure 11. Memory Mapped Registers
COMPLETE MMR LISTING
Note that the Access Type column corresponds to the access
time reading or writing an MMR. It depends on the AMBA bus
used to access the peripheral. The processor has two AMBA
buses: the AHB (advanced high performance bus) used for
system modules and the APB (advanced Peripheral bus) used
for lower performance peripherals.
Rev. PrA | Page 21 of 92
Name
REMAP
RSTSTA
RSTCLR
Byte
1
1
1
Access Type
R/W
R
W
Cycle
1
1
1
ADuC7122
Preliminary Technical Data
Table 12. Timer Base Address = 0xFFFF0300
Address
0x0300
0x0304
0x0308
0x030C
0x0310
0x0314
0x0320
0x0324
0x0328
0x032C
0x0330
0x0340
0x0344
0x0348
0x034C
0x0360
0x0364
0x0368
0x036C
0x0380
0x0384
0x0388
0x038C
0x0390
Name
T0LD
T0VAL0
T0VAL1
T0CON
T0CLRI
T0CAP
T1LD
T1VAL
T1CON
T1CLRI
T1CAP
T2LD
T2VAL
T2CON
T2CLRI
T3LD
T3VAL
T3CON
T3CLRI
T4LD
T4VAL
T4CON
T4CLRI
T4CAP
Byte
2
2
4
4
1
2
4
4
4
1
4
4
4
4
1
2
2
2
1
4
4
4
1
4
Access Type
R/W
R
R
R/W
W
R
R/W
R
R/W
W
R
R/W
R
R/W
W
R/W
R
R/W
W
R/W
R
R/W
W
R
Table 16. ADC Base Address = 0xFFFF0500
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Table 13. PLL Base Address = 0xFFFF0400
Address
0x0404
0x0408
0x040C
0x0410
0x0414
0x0418
Name
POWKEY1
POWCON
POWKEY2
PLLKEY1
PLLCON
PLLKEY2
Byte
2
1
2
2
1
2
Access Type
W
R/W
W
W
R/W
W
Cycle
2
2
2
2
2
2
Address
0x0500
0x0504
0x0508
0x050C
0x0510
0x0514
0x0520
Name
PSMCON
Byte
2
Access Type
R/W
Address
0x0580
0x0584
0x0588
0x058C
0x0590
0x0594
0x0598
0x059C
0x05A0
0x05A4
0x05A8
0x05AC
0x05B0
0x05B4
0x05B8
0x05BC
0x05C0
0x05C4
0x05C8
0x05CC
0x05D0
0x05D4
0x05D8
0x05DC
Cycle
2
Table 15. Reference Base Address = 0xFFFF0480
Address
0x0480
Name
REFCON
Byte
1
Access Type
R/W
Byte
4
1
1
1
4
1
2
Access Type
R/W
R/W
R/W
R
R
W
R/W
Cycle
2
2
2
2
2
2
2
Table 17. DAC Base Address = 0xFFFF0580
Table 14. PSM Base Address = 0xFFFF0440
Address
0x0440
Name
ADCCON
ADCCP
ADCCN
ADCSTA
ADCDAT
ADCRST
PGA_GN
Cycle
2
Rev. PrA | Page 22 of 92
Name
DAC0CON
DAC0DAT
DAC1CON
DAC1DAT
DAC2CON
DAC2DAT
DAC3CON
DAC3DAT
DAC4CON
DAC4DAT
DAC5CON
DAC5DAT
DAC6CON
DAC6DAT
DAC7CON
DAC7DAT
DAC8CON
DAC8DAT
DAC9CON
DAC9DAT
DAC10CON
DAC10DAT
DAC11CON
DAC11DAT
Byte
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
2
4
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Preliminary Technical Data
ADuC7122
Table 20. I2C1 Base Address = 0xFFFF0900
Table 18. UART0 Base Address = 0xFFFF0800
Address
0x0800
0x0804
0x0808
0x080C
0x0810
0x0814
0x0818
0x081C
0x0820
0x0824
0x0828
0X082C
Name
COM0TX
COM0RX
COMDIV0
COMIEN0
COMDIV1
COMIID0
COMCON0
COMCON1
COMSTA0
COMSTA1
COMSCR
COMIEN1
COMIID1
COMADR
COMDIV2
Byte
1
1
1
1
1
1
1
1
1
1
1
1
1
1
2
Access Type
R/W
R
R/W
R/W
R/W
R
R/W
R/W
R
R
R/W
R/W
R
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Table 19. I2C0 Base Address = 0xFFFF0880
Address
0x0880
0x0884
0x0888
0x088C
0x0890
0x0894
0x0898
0x089C
0x08A0
0x08A4
0x08A8
0x08AC
0x08B0
0x08B4
0x08B8
0x08BC
0x08C0
0x08C4
0x08C8
0x08CC
Name
I2C0MCTL
I2C0MSTA
I2C0MRX
I2C0MTX
I2C0MRCNT
I2C0MCRCNT
I2C0ADR1
I2C0ADR2
I2C0SBYTE
I2C0DIV
I2C0SCTL
I2C0SSTA
I2C0SRX
I2C0STX
I2C0ALT
I2C0ID0
I2C0ID1
I2C0ID2
I2C0ID3
I2C0FSTA
Byte
2
2
1
2
2
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
Access Type
R/W
R
R
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Address
0x0900
0x0904
0x0908
0x090C
0x0910
0x0914
0x0918
0x091C
0x0920
0x0924
0x0928
0x092C
0x0930
0x0934
0x0938
0x093C
0x0940
0x0944
0x0948
0x094C
Name
I2C1MCTL
I2C1MSTA
I2C1MRX
I2C1MTX
I2C1MRCNT
I2C1MCRCNT
I2C1ADR0
I2C1ADR1
I2C1SBYTE
I2C1DIV
I2C1SCTL
I2C1SSTA
I2C1SRX
I2C1STX
I2C1ALT
I2C1ID0
I2C1ID1
I2C1ID2
I2C1ID3
I2C1FSTA
Byte
2
2
1
2
2
1
1
1
1
2
2
2
1
1
1
1
1
1
1
1
Access Type
R/W
R
R
R/W
R/W
R
R/W
R/W
R/W
R/W
R/W
R
R
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Table 21. SPI Base Address = 0xFFFF0A00
Address
0x0A00
0x0A04
0x0A08
0x0A0C
0x0A10
Rev. PrA | Page 23 of 92
Name
SPISTA
SPIRX
SPITX
SPIDIV
SPICON
Byte
1
1
1
1
2
Access Type
R
R
W
R/W
R/W
Cycle
2
2
2
2
2
ADuC7122
Preliminary Technical Data
Table 22. PLA Base Address = 0xFFFF0B00
Address
0x0B00
0x0B04
0x0B08
0x0B0C
0x0B10
0x0B14
0x0B18
0x0B1C
0x0B20
0x0B24
0x0B28
0x0B2C
0x0B30
0x0B34
0x0B38
0x0B3C
0x0B40
0x0B44
0x0B48
0x0B4C
0x0B50
Name
PLAELM0
PLAELM1
PLAELM2
PLAELM3
PLAELM4
PLAELM5
PLAELM6
PLAELM7
PLAELM8
PLAELM9
PLAELM10
PLAELM11
PLAELM12
PLAELM13
PLAELM14
PLAELM15
PLACLK
PLAIRQ
PLAADC
PLADIN
PLAOUT
Byte
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
1
4
4
4
4
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Table 24. Flash/EE Block 0 Base Address = 0xFFFF0E00
Address
0x0E00
0x0E04
0x0E08
0x0E0C
0x0E10
0x0E18
0x0E1C
0x0E20
Name
FEE0STA
FEE0MOD
FEE0CON
FEE0DAT
FEE0ADR
FEE0SGN
FEE0PRO
FEE0HID
Byte
1
1
1
2
2
3
4
4
Access Type
R
R/W
R/W
R/W
R/W
R
R/W
R/W
Cycle
1
1
1
1
1
1
1
1
Table 25. Flash/EE Block 1 Base Address = 0xFFFF0E80
Address
0x0E80
0x0E84
0x0E88
0x0E8C
0x0E90
0x0E98
0x0E9C
0x0EA0
Name
FEE1STA
FEE1MOD
FEE1CON
FEE1DAT
FEE1ADR
FEE1SGN
FEE1PRO
FEE1HID
Byte
1
1
1
2
2
3
4
4
Access Type
R
R/W
R/W
R/W
R/W
R
R/W
R/W
Cycle
1
1
1
1
1
1
1
1
Table 26. PWM Base Address= 0xFFFF0F80
Table 23. GPIO Base Address = 0xFFFF0D00
Address
0x0D00
0x0D04
0x0D08
0x0D0C
0x0D10
0x0D20
0x0D24
0x0D28
0x0D2C
0x0D30
0x0D34
0x0D38
0x0D3C
0x0D40
0x0D44
0x0D48
0x0D50
0x0D54
0x0D58
0x0D5C
Name
GP0CON
GP1CON
GP2CON
GP3CON
GP4CON
GP0DAT
GP0SET
GP0CLR
GP0PAR
GP1DAT
GP1SET
GP1CLR
GP1PAR
GP2DAT
GP2SET
GP2CLR
GP3DAT
GP3SET
GP3CLR
GP3PAR
Byte
4
4
4
4
4
4
1
1
4
4
1
1
4
4
1
1
4
1
1
4
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
W
W
R/W
R/W
W
W
R/W
R/W
W
W
R/W
W
W
R/W
Cycle
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
1
Address
0x0F80
0x0F84
0x0F88
0x0F8C
0x0F90
0x0F94
0x0F98
0x0F9C
0x0FA0
0x0FA4
0x0FA8
0x0FAC
0x0FB0
0x0FB4
0x0FB8
Rev. PrA | Page 24 of 92
Name
PWMCON1
PWM1COM1
PWM1COM2
PWM1COM3
PWM1LEN
PWM2COM1
PWM2COM2
PWM2COM3
PWM2LEN
PWM3COM1
PWM3COM2
PWM3COM3
PWM3LEN
PWMCON2
PWMICLR
Byte
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Access Type
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
W
Cycle
2
2
2
2
2
2
2
2
2
2
2
2
2
2
2
Preliminary Technical Data
ADuC7122
ADC CIRCUIT OVERVIEW
The analog-to-digital converter (ADC) incorporates a fast,
multichannel, 12-bit ADC. It can operate from 3.0 V to 3.6 V
supplies and is capable of providing a throughput of up to 1 MSPS
when the clock source is 41.78 MHz. This block provides the
user with a multichannel multiplexer, differential track-andhold, on-chip reference, and ADC.
The ADC consists of a 12-bit successive approximation converter
based around two capacitor DACs. Depending on the input
signal configuration, the ADC can operate in one of the
following three modes:



Fully differential mode, for small and balanced signals
Single-ended mode, for any single-ended signals
Pseudo differential mode, for any single-ended signals,
taking advantage of the common mode rejection offered by
the pseudo differential input
The converter accepts an analog input range of 0 to VREF when
operating in single-ended mode or pseudo differential mode. In
fully differential mode, the input signal must be balanced around
a common-mode voltage VCM, in the range 0 V to AVDD and
with maximum amplitude of 2 VREF (see Figure 12).
Single or continuous conversion modes can be initiated in
software. An external CONVST pin, an output generated from
the on-chip PLA, a Timer0, or a Timer1 overflow can also be
used to generate a repetitive trigger for ADC conversions.
If the signal has not been de-asserted by the time the ADC
conversion is complete, a second conversion begins
automatically.
A voltage output from an on-chip band gap reference proportional to absolute temperature can also be routed through the
front-end ADC multiplexer, effectively an additional ADC
channel input. This facilitates an internal temperature sensor
channel, measuring die temperature to an accuracy of 3C.
For the ADuC7122 a number of modifications have been made
to the ADC input structure that appeared on the ADuC702x
family.
The PADC0 and PADC1 inputs connect to a PGA and allow for
gain from 1 to 5 with 32 steps. The remaining channels can be
configured as single or differential. A buffer is provided before
the ADC for measuring internal channels.
AVDD
VCM
VCM
2VREF
06020-028
VCM
0
2VREF
2VREF
Figure 12. Examples of Balanced Signals for Fully Differential Mode
A high precision, low drift, and factory-calibrated 2.5 V reference
is provided on-chip. An external reference can also be connected
as described in the Band Gap Reference section.
Rev. PrA | Page 25 of 92
ADuC7122
Preliminary Technical Data
SIGN
BIT
0 1111 1111 1110
ADC TRANSFER FUNCTION
Pseudo Differential and Single-Ended Modes
0 1111 1111 1100
In pseudo differential or single-ended mode, the input range is
0 to VREF. The output coding is straight binary in pseudo
differential and single-ended modes with
2 × VREF
4096
OUTPUT CODE
0 1111 1111 1010
1 LSB = FS/4096 or
2.5 V/4096 = 0.61 mV or
610 μV when VREF = 2.5 V
0 0000 0000 0001
0 0000 0000 0000
1 1111 1111 1110
1 0000 0000 0100
The ideal code transitions occur midway between successive
integer LSB values (that is, 1/2 LSB, 3/2 LSBs, 5/2 LSBs, …,
FS – 3/2 LSBs). The ideal input/output transfer characteristic is
shown in Figure 13.
1 0000 0000 0000
–VREF + 1LSB
0LSB
+VREF – 1LSB
VOLTAGE INPUT (VIN+ – VIN–)
06020-030
1 0000 0000 0010
Figure 14. ADC Transfer Function in Differential Mode
PADC0/PADC1 in Optical Applications
1111 1111 1111
An external precision resistor converts the current to voltage
and the PGA then amplifies this voltage signal with gain up to 5
by 32 steps. The intention is to compensate the variation of the
detector diode responsitivity and normalize optical power read
by ADC. The external resistor is assumed to be 0.1% accuracy,
5 ppm. A 1 nF capacitor is shunted with the resistor to suppress
wide band noise. The resistor value should be selected such that
the FS voltage developed on the resistor is less than AVDD − 1.2
V, or typically 1.8 V.
1111 1111 1110
1111 1111 1101
OUTPUT CODE
1LSB =
1111 1111 1100
1LSB =
FS
4096
0000 0000 0011
0000 0000 0010
0000 0000 0000
0V 1LSB
+FS – 1LSB
VOLTAGE INPUT
06020-029
0000 0000 0001
The PGA is designed to handle 10 mV minimum input.
To minimize noise, the ADC input buffer should be bypassed.
Figure 13. ADC Transfer Function in Pseudo Differential Mode or
Single-Ended Mode
Fully Differential Mode
The amplitude of the differential signal is the difference
between the signals applied to the VIN+ and VIN− inputs (that is,
VIN+ − VIN−) of the currently enabled differential channel. The
maximum amplitude of the differential signal is therefore −VREF
to +VREF p-p (2 × VREF). This is regardless of the common mode
(CM). The common mode is the average of the two signals
(VIN+ + VIN−)/2, and is, therefore, the voltage that the two inputs
are centered on. This results in the span of each input being CM
± VREF/2. This voltage has to be set up externally, and its range
varies with VREF (see the Driving the Analog Inputs section).
The output coding is twos complement in fully differential
mode with 1 LSB = 2 VREF/4096 or 2 × 2.5 V/4096 = 1.22 mV
when VREF = 2.5 V. The output result is ±11 bits, but this is
shifted by one to the right. This allows the result in ADCDAT to
be declared as a signed integer when writing C code. The
designed code transitions occur midway between successive
integer LSB values (that is, 1/2 LSB, 3/2 LSBs, 5/2 LSBs, …,
FS − 3/2 LSBs). The ideal input/output transfer characteristic is
shown in Figure 14.
PADC1 is driven by a buffer to 0.15 V to keep the PGA from
saturation when the input current drops to 0. The buffer can be
disabled by setting ADCCON[14] so that the PADC1 can be
connected to GND as well. This is the same for PADC0.
The ADC needs to be placed in pseudo differential mode and
assumes negative input is close to ground.
All the controls are independently set through register bits to
give maximum flexibility to the user. Typically, users need to set
the following steps (using PADC1 as an example):
1.
2.
3.
Select PADC1P as the PGA input, then select PGA output
as mux input. Enable the PADC1N buffer and disable the
ADC input buffer.
Set the proper gain value for the PGA. Bypass the buffer.
Set the ADC to pseudo differential mode and start
conversion.
All the controls are independently set through register bits for
maximum flexibility to the user. Typically, users must set the
following (using PADC0 as an example):




Select PADC0P as PGA input, select PGA output as MUX
input. Enable PADC0N buffer, disable ADC input buffer.
Set proper gain value for the PGA; bypass the buffer
ADC: set to pseudo differential mode, start conversion.
Removing offset and 1/f noise requires performing two
conversions on the input signal.
Rev. PrA | Page 26 of 92
Preliminary Technical Data

ADuC7122
Set pga1_chop to 0 for the first conversion and pga1_chop
= 1 for the second. Then calculate the average value.
Thermistor and Other Input Channels
ADuC7122 provides 2 pairs of thermistor inputs and 7 extra
differential input pins. These pins can also be configured as
differential input pair or single ended input or pseudo
differential inputs. The buffer and ADC are configured
independently from input channel selection. Note that the input
range of ADC input buffer is from 0.15V to AVDD-0.15V, if the
input signal range exceeds this range, the input buffer must be
bypassed.
The ADuC7122 provide 2 pins for each thermistor input. The
negative input is to remove error of ground difference. When
selecting the thermistor input, the negative side buffer should
always be bypassed to make sure the amplifier is not saturated.
The ADC should be configured to work in positive pseudo
differential mode.
Besides these external inputs, ADC can also select internal
inputs to monitor the IOVDD power supply.
An on chip diode can also be selected to provide chip
temperature monitoring. ADC can also select VREF and AGND
as input for calibration purpose
PGA and Input Buffer
The PGA is a one stage positive gain amplifier that is be able to
accept input from 0.1V to AVDD-1.2V and the output swing
should be at least 2.5V. The gain of the PGA is from 1 to 5 with
32 linear steps. PGA cannot be bypassed for the PADC0 and
PADC1 channels.
The PGAs use PMOS input to minimize nonlinearity and noise.
The input level for PGA is limited to AVDD-1.2V ~0.1V to
make sure amplifiers are not saturated. The input buffer is railto-rail buffer. It can accept signal from 0.15V to AVDD-0.15V.
Each of input buffers can be bypassed independently.
The PGA can be chopped to remove offset and 1/f noise. The
user need to manually chop the PGA for single conversion
while it is automatically chopped when chop mode is enabled.
TYPICAL OPERATION
Once configured via the ADC control and channel selection
registers, the ADC converts the analog input and provides
a 12-bit result in the ADC data register.
Calibration
By default, the factory-set values written to the ADC offset
(ADCOF) and gain coefficient registers (ADCGN) yield optimum performance in terms of end-point errors and linearity
for standalone operation of the part (see the Specifications
section). If system calibration is required, it is possible to modify the default offset and gain coefficients to improve end-point
errors, but note that any modification to the factory-set ADCOF
and ADCGN values can degrade ADC linearity performance.
For system offset error correction, the ADC channel input stage
must be tied to AGND. A continuous software ADC conversion
loop must be implemented by modifying the value in ADCOF
until the ADC result (ADCDAT) reads Code 0 to Code 1. If
the ADCDAT value is greater than 1, ADCOF should be decremented until ADCDAT reads Code 0 to Code 1. Offset error
correction is performed digitally and has a resolution of 0.25 LSB
and a range of ±3.125% of VREF.
For system gain error correction, the ADC channel input stage
must be tied to VREF. A continuous software ADC conversion
loop must be implemented to modify the value in ADCGN
until ADCDAT reads Code 4094 to Code 4095. If the ADCDAT
value is less than 4094, ADCGN should be incremented until
ADCDAT reads Code 4094 to Code 4095. Similar to the offset
calibration, the gain calibration resolution is 0.25 LSB with a
range of ±3% of VREF.
Current Consumption
The ADC in standby mode, that is, powered up but not
converting, typically consumes 640 μA. The internal reference
adds 140 μA. During conversion, the extra current is 0.3 μA,
multiplied by the sampling frequency (in kHz).
Timing
Figure 16 gives details of the ADC timing. Users control the
ADC clock speed and the number of acquisition clock in the
ADCCON MMR. By default, the acquisition time is eight clocks
and the clock divider is two. The number of extra clocks (such
as bit trial or write) is set to 19, giving a sampling rate of 774 kSPS.
For conversion on the temperature sensor, the ADC acquisition
time is automatically set to 16 clocks and the ADC clock divider
is set to 32. When using multiple channels, including the
temperature sensor, the timing settings revert back to the userdefined settings after reading the temperature sensor channel.
The top four bits are the sign bits, and the 12-bit result is placed
from Bit 16 to Bit 27, as shown in Figure 15. Again, it should be
noted that in fully differential mode, the result is represented in
twos complement format, and in pseudo differential and singleended mode, the result is represented in straight binary format.
SIGN BITS
27
16 15
12-BIT ADC RESULT
0
06020-031
31
Figure 15. ADC Result Format
Rev. PrA | Page 27 of 92
ADuC7122
Preliminary Technical Data
ACQ
BIT TRIAL
WRITE
TEMPERATURE SENSOR
The ADuC7122 provides a voltage output from an on-chip
band gap reference proportional to absolute temperature. This
voltage output can also be routed through the front-end ADC
multiplexer (effectively, an additional ADC channel input),
facilitating an internal temperature sensor channel that
measures die temperature.
ADC CLOCK
CONVSTART
ADCBUSY
The internal temperature sensor is not designed for use as an
absolute ambient temperature calculator. It is intended for use
as an approximate indicator of the temperature of the
ADuC7122 die.
ADCSTA = 0
ADCSTA = 1
ADC INTERRUPT
Figure 16. ADC Timing
06020-032
DATA
ADCDAT
The typical temperature coefficient is −0.707 mV/°C.
ADC MMRs Interface
The ADC is controlled and configured via a number of MMRs
(see Table 27) that are described in detail in the following pages.
ADC Output vs. Temperature
Table 27. ADC MMRs
Name
ADCCON
ADCCP
ADCCN
ADCSTA
ADCDAT
ADCRST
PGA_GN
Description
ADC control register. Allows the programmer to enable the ADC peripheral, to select the mode of operation of the ADC (either
single-ended, pseudo differential, or fully differential mode), and to select the conversion type (see Table 28).
ADC positive channel selection register.
ADC negative channel selection register.
ADC status register. Indicates when an ADC conversion result is ready. The ADCSTA register contains only one bit, ADCREADY
(Bit 0), representing the status of the ADC. This bit is set at the end of an ADC conversion generating an ADC interrupt. It is
cleared automatically by reading the ADCDAT MMR. When the ADC is performing a conversion, the status of the ADC can be
read externally via the ADCBusy pin. This pin is high during a conversion. When the conversion is finished, ADCBusy goes back low.
This information can be available on P0.5 (see the General-Purpose I/O section) if enabled in GP0CON register.
ADC data result register. Holds the 12-bit ADC result, as shown Table 30.
ADC reset register. Resets all the ADC registers to their default value.
Gain of PADC0 and PADC1.
Rev. PrA | Page 28 of 92
Preliminary Technical Data
ADuC7122
Table 28. ADCCON MMR Bit Designations (Address = 0xFFFF0500, Default Value = 0x00000A00)
Bit
31:16
15
Value
000
Description
These bits are reserved.
Positive ADC buffer bypass.
Set to 0 by the user to enable the positive ADC buffer.
Set to 1 by the user to bypass the positive ADC buffer.
Negative ADC buffer bypass.
Set to 0 by the user to enable the negative ADC buffer.
Set to 1 by the user to bypass the negative ADC buffer.
ADC clock speed (fADC = fCORE, conversion = 19 ADC clocks + acquisition time).
fADC/1. This divider is provided to obtain 1 MSPS ADC with an external clock <41.78 MHz.
fADC/2 (default value).
fADC/4.
fADC/8.
fADC/16.
fADC/32.
ADC acquisition time (number of ADC clocks).
2 clocks.
4 clocks.
8 clocks (default value).
16 clocks.
32 clocks
64 clocks
Enable conversion.
Set by user to 1 to enable conversion mode.
Cleared by user to 0 to disable conversion mode.
Reserved. This bit should be set to 0 by the user.
ADC power control.
Set by user to 1 to place the ADC in normal mode. The ADC must be powered up for at least 5 μs before it converts
correctly.
Cleared by user to 0 to place the ADC in power-down mode.
Conversion mode.
Single-ended mode.
Differential mode.
Pseudo differential mode.
Reserved.
Conversion type.
Enable CONVST pin as a conversion input.
001
010
011
100
101
110
Other
Enable Timer1 as a conversion input.
Enable Timer0 as a conversion input.
Single software conversion. Automatically set to 000 after conversion.
Continuous software conversion.
PLA conversion.
Reserved
Reserved.
0
1
14
0
1
13:11
000
001
010
011
100
101
10:8
000
001
010
011
100
101
7
6
5
4:3
00
01
10
11
2:0
Rev. PrA | Page 29 of 92
ADuC7122
Preliminary Technical Data
Table 29. ADCCP MMR Bit Designations
(Address = 0xFFFF0504, Default Value = 0x00)
Table 30. ADCCN MMR Bit Designations
(Address = 0xFFFF0508, Default Value = 0x00)
Bit
7:5
4:0
Bit
7:5
4:0
Value
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
10010
10011
10100
10101
10110
10111
Others
Description
Reserved
Positive channel selection bits
PADC0P
PADC1P
ADC0
ADC1
ADC2
ADC3
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10/AINCM
Temperature sensor
Reserved
Reserved
Reserved
Reserved
Reserved
IOVDD_MON
Reserved
Reserved
VREF
AGND
Reserved
Value
00000
00001
00010
00011
00100
00101
00110
Description
Reserved
Negative channel selection bits
PADC0P
PADC1P
PADC0P
PADC1P
ADC0
ADC1
ADC2
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
Others
ADC3
ADC4
ADC5
ADC6
ADC7
ADC8
ADC9
ADC10/AINCM
PGND
IOGND
Reserved
Table 31. ADCSTA MMR Bit Designations
(Address = 0xFFFF050C, Default Value = 0x00)
Bit
0
Value
1
0
0
Description
Indicates that an ADC conversion is complete.
It is set automatically once an ADC conversion
completes.
Automatically cleared by reading the ADCDAT
MMR.
Table 32. ADCDAT MMR Bit Designations
(Address = 0xFFFF0510, Default Value = 0x00000000)
Bit
27:16
Value
Description
Holds the ADC result (see Figure 15).
Table 33. ADCRST MMR Bit Designations
(Address = 0xFFFF0514, Default Value = 0x00)
Bit
0
Value
1
Description
Set to 1 by the user to reset all the ADC
registers to their default values.
Table 34. PGA_GN MMR Bit Designations
(Address = 0xFFFF0520, Default Value = 0x00)
Bit
11:6
5:0
Value
Description
Gain of PGA for PADC0 (PGA_PADC0_GN)
= 1 + 4 × (PGA_ADC0_GN/32)
Gain of PGA for PADC1 (PGA_PADC1_GN)
= 1 + 4 × (PGA_ADC1_GN/32)
Note that PGA_PADC0_GN and PGA_PADC1_GN must be ≤32.
Rev. PrA | Page 30 of 92
Preliminary Technical Data
ADuC7122
CONVERTER OPERATION
Pseudo Differential Mode
The ADC incorporates a successive approximation (SAR)
architecture involving a charge-sampled input stage. This
architecture is described for the three different modes of
operation: differential mode, pseudo differential mode, and
single-ended mode.
In pseudo differential mode, Channel− is linked to the VIN−
input of the ADuC7122, and SW2 switches between A
(Channel−) and B (VREF). The VIN− input must be connected to
ground or a low voltage. The input signal on VIN+ can then vary
from VIN− to VREF + VIN−. Note that VIN− must be selected so that
VREF + VIN− does not exceed AVDD.
The ADuC7122 contains a successive approximation ADC
based on two capacitive DACs. Figure 17 and Figure 18 show
simplified schematics of the ADC in acquisition and conversion
phase, respectively. The ADC comprises control logic,
a SAR, and two capacitive DACs. In Figure 17 (the acquisition
phase), SW3 is closed and SW1 and SW2 are in Position A. The
comparator is held in a balanced condition, and the sampling
capacitor arrays acquire the differential signal on the input.
CAPACITIVE
DAC
CHANNEL+
AIN0
CS
B
COMPARATOR
A SW1
MUX
A
AIN11
SW2
CS
SW3
CONTROL
LOGIC
B
VREF
VIN–
CAPACITIVE
DAC
CHANNEL–
06020-035
Differential Mode
Figure 19. ADC in Pseudo Differential Mode
CAPACITIVE
DAC
CHANNEL+
AIN0
B
CS
A SW1
MUX
CHANNEL– A SW2
AIN11
CS
Single-Ended Mode
COMPARATOR
SW3
In single-ended mode, SW2 is always connected internally to
ground. The VIN− input can be floating. The input signal range
on VIN+ is 0 V to VREF.
CONTROL
LOGIC
CAPACITIVE
DAC
Figure 17. ADC Acquisition Phase
CAPACITIVE
DAC
CHANNEL+
B
CS
COMPARATOR
A SW1
MUX
CS
SW3
CONTROL
LOGIC
B
VREF
Figure 18. ADC Conversion Phase
CAPACITIVE
DAC
06020-034
AIN11
CHANNEL– A SW2
CHANNEL+
AIN0
B
CS
COMPARATOR
A SW1
When the ADC starts a conversion (see Figure 18), SW3 opens
and SW1 and SW2 move to Position B, causing the comparator
to become unbalanced. Both inputs are disconnected once the
conversion begins. The control logic and the charge redistribution
DACs are used to add and subtract fixed amounts of charge
from the sampling capacitor arrays to bring the comparator
back into a balanced condition. When the comparator is
rebalanced, the conversion is complete. The control logic generates
the ADC output code. The output impedances of the sources
driving the VIN+ and VIN− inputs must be matched; otherwise, the
two inputs have different settling times, resulting in errors.
AIN0
CAPACITIVE
DAC
MUX
AIN11
CS
SW3
CONTROL
LOGIC
CHANNEL–
CAPACITIVE
DAC
06020-036
VREF
06020-033
B
Figure 20. ADC in Single-Ended Mode
Analog Input Structure
Figure 21 shows the equivalent circuit of the analog input
structure of the ADC. The four diodes provide ESD protection
for the analog inputs. Care must be taken to ensure that the
analog input signals never exceed the supply rails by more than
300 mV. Voltage in excess of 300 mV can cause these diodes to
become forward biased and start conducting into the substrate.
These diodes can conduct up to 10 mA without causing
irreversible damage to the part.
The C1 capacitors in Figure 21 are typically 4 pF and can be
primarily attributed to pin capacitance. The resistors are lumped
components made up of the on resistance of the switches. The
value of these resistors is typically about 100 Ω. The C2 capacitors
are the ADC sampling capacitors and have a capacitance of 16 pF
typical.
Rev. PrA | Page 31 of 92
ADuC7122
Preliminary Technical Data
AVDD
DRIVING THE ANALOG INPUTS
D
C1
Internal or external reference can be used for the ADC. In
differential mode of operation, there are restrictions on the
common-mode input signal (VCM) that are dependent on
reference value and supply voltage used to ensure that the signal
remains within the supply rails.
R1 C2
D
AVDD
D
D
Table 35. VCM Ranges
06020-037
C1
Table 35 gives some calculated VCM minimum and VCM
maximum values.
R1 C2
AVDD
3.3 V
Figure 21. Equivalent Analog Input Circuit Conversion Phase:
Switches Open, Track Phase: Switches Closed
For ac applications, removing high frequency components from
the analog input signal is recommended through the use of an
RC low-pass filter on the relevant analog input pins. In applications
where harmonic distortion and signal-to-noise ratio are critical,
the analog input should be driven from a low impedance source.
Large source impedances significantly affect the ac performance
of the ADC and can necessitate the use of an input buffer amplifier.
The choice of the op amp is a function of the particular application.
Figure 22 and Figure 23 give an example of an ADC front end.
3.0 V
VREF
2.5 V
2.048 V
1.25 V
2.5 V
2.048 V
1.25 V
VCM Min
1.25 V
1.024 V
0.75 V
1.25 V
1.024 V
0.75 V
VCM Max
2.05 V
2.276 V
2.55 V
1.75 V
1.976 V
2.25 V
Signal Peak-to-Peak
2.5 V
2.048 V
1.25 V
2.5 V
2.048 V
1.25 V
ADuC7122
10W
ADC0
0.01mF
Figure 22. Buffering Single-Ended/Pseudo Differential Input
Figure 24. ADC Output vs. Temperature
ADuC7122
ADC0
Vref
ADC1
Figure 23. Buffering Differential Inputs
When no amplifier is used to drive the analog input, the source
impedance should be limited to values lower than 1 kΩ. The
maximum source impedance depends on the amount of total
harmonic distortion (THD) that can be tolerated. The THD
increases as the source impedance increases and the
performance degrades.
Rev. PrA | Page 32 of 92
Preliminary Technical Data
ADuC7122
BAND GAP REFERENCE
The ADuC7122 provide an on-chip band gap reference of 2.5 V
that can be used for the ADC and for the DAC. This 2.5 V
reference is generated from a 1.2V reference.
This internal reference also appears on the VREF_2.5pin. When
using the internal reference, two 0.47 μF capacitors must be
connected from the external VREF 2.5 V and VREF 1.2 V pins to
AGND to ensure stability and fast response during ADC
conversions. This reference can also be connected to an external
pin (VREF) and used as a reference for other circuits in the system.
B
B
B
B
The band gap reference also connects through buffers to the
BUF_VREF1 and the BUF_VREF2 pins. A minimum of 0.1 μF
capacitor should be connected to these pins to damp noise.
The band gap reference interface consists of an 8-bit REFCON
MMR, described in Table 36.
POWER SUPPLY MONITOR
The power supply monitor on the ADuC7122 indicates when
the IOVDD supply pin drops below one of two supply trip points.
The monitor function is controlled via the PSMCON register. If
enabled in the IRQEN or FIQEN register, the monitor
interrupts the core using the PSMI bit in the PSMCON MMR.
This bit is cleared immediately when CMP goes high. Note that
if the interrupt generated is exited before CMP goes high
(IOVDD is above the trip point), no further interrupts are
B
B
generated until CMP returns high. The user should ensure that
code execution remains within the ISR until CMP returns high.
This monitor function allows the user to save working registers
to avoid possible data loss due to the low supply or brown-out
conditions. It also ensures that normal code execution does not
resume until a safe supply level has been established.
When the ADC channel selection bits are configured to
IOVDD_MON, this permits the ADC to convert the voltage
available at the input of the power supply monitor comparator.
When measuring an internal channel, the internal buffer should
be enabled. The internal buffer should be enabled to isolate the
external interference when sampling any of the internal
channels. Before measuring this voltage, the following sequence
is required.
1.
2.
3.
4.
Measure VREF using the ADC.
Set ADCCP = IOVDD_MON channel.
Set a typical delay of 60 μs.
Perform ADC conversion on the IOVDD_MON channel
(Use anADCCON value of 0x2AA3 for optimum results).
The delay between the ADC mux select switching and the
initiation of the conversion is required to allow the voltage on
the ADC sampling capacitor to settle to the divided down
supply voltage.
Table 36. REFCON MMR Bit Designations (Address = 0xFFFF0480, Default Value = 0x01)
Bit
7:1
2
1
0
Description
Reserved.
BUF_VREF is driven from the internal 2.5 V reference when set to 1.
Internal 2.5 V reference output enable.
Set by user to connect the internal 2.5 V reference to the VREF_2.5 pin.
Cleared by user to disconnect the reference from the VREF_2.5 pin. This pin should also be cleared to connect an external reference
source to the VREF_2.5 pin.
Internal 1.2 V reference output enable.
Set by user to connect the internal 1.2 V reference to the VREF_1.2 pin.
Cleared by user to disconnect the reference from the VREF_1.2 pin.
Table 37. PSMCON MMR Bit Designations (Address = 0xFFFF0440, Default Value = 0x08 or 0x00 (Dependent on Device Supply Level)
Bit
3
Name
CMP
2
TP
1
PSMEN
0
PSMI
Description
Comparator bit. This is a read-only bit that directly reflects the state of the comparator.
Read 1 indicates the IOVDD supply is above its selected trip point or the PSM is in power-down mode.
Read 0 indicates the IOVDD supply is below its selected trip point. This bit should be set before leaving the interrupt
service routine.
Trip point selection bit.
0 = 2.79 V
1 = 3.07 V
Power supply monitor enable bit.
Set to 1 by the user to enable the power supply monitor circuit.
Cleared to 0 by the user to disable the power supply monitor circuit.
Power supply monitor interrupt bit. This bit is set high by the MicroConverter® if CMP is low, indicating low I/O supply.
The PSMI Bit can be used to interrupt the processor. Once CMP returns high, the PSMI bit can be cleared by writing a 1
to this location. A write of 0 has no effect. There is no timeout delay. PSMI can be cleared immediately once CMP goes
high.
B
B
B
B
Rev. PrA | Page 33 of 92
ADuC7122
Preliminary Technical Data
NONVOLATILE FLASH/EE MEMORY
Like EEPROM, Flash memory can be programmed in-system
at a byte level, although it must first be erased. The erase is
performed in page blocks. As a result, Flash memory is often
and more correctly referred to as Flash/EE memory.
Overall, Flash/EE memory represents a step closer to the ideal
memory device that includes no volatility, in-circuit
programmability, high density, and low cost. Incorporated in
the ADuC7122, Flash/EE memory technology allows the user to
update program code space in-circuit, without the need to
replace one-time programmable (OTP) devices at remote
operating nodes.
FLASH/EE MEMORY
The ADuC7122 contains two 64 kB arrays of Flash/EE memory.
In the upper block of Flash/EE memory, the bottom 62 Kb are
available to the user and the top 2 kB of this Flash/EE program
memory array contain permanently embedded firmware,
allowing in-circuit serial download. The 2 Kb of embedded
firmware also contain a power-on configuration routine that
downloads factory calibrated coefficients to the various
calibrated peripherals (band gap references and so on). This 2
kB embedded firmware is hidden from user code. It is not possible
for the user to read, write, or erase this page. In the second block,
all 64 kB of Flash/EE memory are available to the user.
Retention quantifies the ability of the Flash/EE memory to
retain its programmed data over time. Again, the parts are
qualified in accordance with the formal JEDEC Retention
Lifetime Specification (A117) at a specific junction temperature
(TJ = 85°C). As part of this qualification procedure, the
Flash/EE memory is cycled to its specified endurance limit,
described previously, before data retention is characterized.
This means that the Flash/EE memory is guaranteed to retain
its data for its fully specified retention lifetime every time the
Flash/EE memory is reprogrammed. Note, too, that retention
lifetime, based on activation energy of 0.6 eV, derates with
TJ, as shown in Figure 25.
600
450
300
150
The 126 kB of Flash/EE memory can be programmed in-circuit,
using the serial download mode or the JTAG mode provided.
0
04955-085
The ADuC7122 incorporates Flash/EE memory technology onchip to provide the user with non-volatile, in-circuit
reprogrammable memory space.
As indicated in the Specifications section, the Flash/EE memory
endurance qualification is carried out in accordance with JEDEC
Retention Lifetime Specification A117 over the industrial temperature range of –10° to +95°C. The results allow the specification
of a minimum endurance figure over a varying supply across
the industrial temperature range for 10,000 cycles.
RETENTION (Years)
FLASH/EE MEMORY OVERVIEW
30
Flash/EE Memory Reliability
The Flash/EE memory arrays on the ADuC7122 is fully
qualified for two key Flash/EE memory characteristics:
Flash/EE memory cycling endurance and Flash/EE memory
data retention.
Endurance quantifies the ability of the Flash/EE memory to be
cycled through many program, read, and erase cycles. A single
endurance cycle is composed of four independent, sequential
events, defined as
1.
2.
3.
4.
Initial page erase sequence
Read/verify sequence a single Flash/EE
Byte program sequence memory
Second read/verify sequence endurance cycle
In reliability qualification, three separate page blocks from each
Flash/EE memory block is tested. An entire Flash/EE page at
the top, middle, and bottom of each Flash/EE memory block is
cycled 10,000 times from 0x0000 to 0xFFFF.
40
55
70
85
100
125
JUNCTION TEMPERATURE (°C)
135
150
Figure 25. Flash/EE Memory Data Retention
Serial Downloading (In-Circuit Programming)
The ADuC7122 facilitates code download via the I2C serial
port. The ADuC7122 enters serial download mode after a reset
or power cycle if the BM pin is pulled low through an external
1 kΩ resistor. This is combined with the state of address
0x00014 in the flash. If this address is 0xFFFFFFFF and the BM
pin is pulled low the part will enter download mode, if this
address contains any other value user code is executed. Once in
serial download mode, the user can download code to the full
126 kB of Flash/EE memory while the device is in-circuit in its
target application hardware. A PC serial download executable and
hardware dongle are provided as part of the development system
for serial downloads via the I2C port.
JTAG Access
The JTAG protocol uses the on-chip JTAG interface to
facilitate code download and debug.
Rev. PrA | Page 34 of 92
Preliminary Technical Data
ADuC7122
FLASH/EE MEMORY SECURITY
The 126 kB of Flash/EE memory available to the user can be
read and write protected. Bit 31 of the FEE0PRO/FEE0HID
MMR protects the 126 kB from being read through JTAG and also
in parallel programming mode. The other 31 bits of this register
protect writing to the Flash/EE memory; each bit protects four
pages, that is, 2 kB. Write protection is activated for all access
types. FEE1PRO and FEE1HID similarly protect the second
64 kB block. All 32 bits of this are used to protect four pages at a
time.
Protection can be set by writing into FEExPRO MMR. It takes
effect only after a save protection command (0x0C) and a reset.
The FEExPRO MMR is protected by a key to avoid direct access.
The key is saved once and must be entered again to modify
FEExPRO. A mass erase sets the key back to 0xFFFF but also
erases all the user code.
The Flash/EE memory can be permanently protected by using
the FEEPRO MMR and a particular value of the 0xDEADDEAD
key. Entering the key again to modify the FEExPRO register is
not allowed.
Sequence to Write the Key
3.
4.
5.
//Protect pages 4 to 7
//Write key enable
//16 bit key value
//16 bit key value
// Write key command
The same sequence should be followed to protect the part
permanently with FEExADR = 0xDEAD and FEExDAT =
0xDEADDEAD.
Table 38. FEE0DAT Register
Protection can be set and removed by writing directly into
FEExHID MMR. This protection does not remain after reset.
2.
FEE0PRO=0xFFFFFFFD;
FEE0MOD=0x48;
FEE0ADR=0x1234;
FEE0DAT=0x5678;
FEE0CON= 0x0C;
FLASH/EE CONTROL INTERFACE
Three Levels of Protection
1.
The sequence to write the key is shown in the following example;
this protects writing Page 4 to Page 7 of the Flash/EE memory:
Write the bit in FEExPRO corresponding to the page to be
protected.
Enable key protection by setting Bit 6 of FEExMOD (Bit 5
must equal 0).
Write a 32-bit key in FEExADR, FEExDAT.
Run the write key command 0×0C in FEExCON; wait for
the read to be successful by monitoring FEExSTA.
Reset the part.
To remove or modify the protection, the same sequence is used
with a modified value of FEExPRO. If the key chosen is the value
0xDEADDEAD, then the memory protection cannot be removed.
Only a mass erase unprotects the part; however, it also erases all
user code.
Name
FEE0DAT
Address
0xFFFF0E0C
Default Value
0xXXXX
Access
R/W
FEE0DAT is a 16-bit data register.
Table 39. FEE0ADR Register
Name
FEE0ADR
Address
0xFFFF0E10
Default Value
0x0000
Access
R/W
FEE0ADR is a 16-bit address register.
Table 40. FEE0SGN Register
Name
FEE0SGN
Address
0xFFFF0E18
Default Value
0xFFFFFF
Access
R
FEE0SGN is a 24-bit code signature.
Table 41. FEE0PRO Register
Name
FEE0PRO
Address
0xFFFF0E1C
Default Value
0x00000000
Access
R/W
FEE0PRO provides protection following subsequent reset MMR.
It requires a software key (see Table 57). As stated previously,
each bit from 30 to 0 of the FEEXPRO register protects a 2 kB
block of memory; that is, setting Bit 0 low protects Page 0 to
Page 3 and setting Bit 2 low protects Page 8 to Page 11.
Table 42. FEE0HID Register
Name
FEE0HID
Address
0xFFFF0E20
Default Value
0xFFFFFFFF
Access
R/W
FEE0HID provides immediate protection MMR. It does not
require any software keys (see Table 57).
Command Sequence for Executing a Mass Erase
FEE0DAT = 0x3CFF;
FEE0ADR = 0xFFC3;
FEE0MOD = FEE0MOD|0x8;
//Erase key enable
FEE0CON = 0x06;
//Mass erase command
Rev. PrA | Page 35 of 92
ADuC7122
Preliminary Technical Data
Table 43. FEE1DAT Register
Name
FEE1DAT
Address
0xFFFF0E8C
Default Value
0xXXXX
Access
R/W
Table 44. FEE1ADR Register
Address
0xFFFF0E90
Default Value
0x0000
Access
R/W
FEE1ADR is a 16-bit address register.
Address
0xFFFF0E98
Address
0xFFFF0E00
Name
FEE1STA
Address
0xFFFF0E80
Default Value
0xFFFFFF
Access
R
Name
FEE0MOD
Address
0xFFFF0E04
Table 51. FEE1MOD Register
Table 46. FEE1PRO Register
Name
FEE1MOD
Address
0xFFFF0E9C
Default Value
0x00000000
Access
R/W
Address
0xFFFF0E84
Name
FEE0CON
Table 47. FEE1HID Register
Table 53. FEE1CON Register
Address
0xFFFF0EA0
Default Value
0x0000
Access
RW
Default Value
0x80
Access
RW
Default Value
0x80
Access
RW
Default Value
0x0000
Access
RW
Default Value
0x0000
Access
RW
Table 52. FEE0CON Register
FEE1PRO provides protection following subsequent reset MMR.
It requires a software key (see Table 58).
Name
FEE1HID
Access
RW
Table 49. FEE1STA Register
FEE1SGN is a 24-bit code signature.
Name
FEE1PRO
Default Value
0x0000
Table 50. FEE0MOD Register
Table 45. FEE1SGN Register
Name
FEE1SGN
Table 48. FEE0STA Register
Name
FEE0STA
FEE1DAT is a 16-bit data register.
Name
FEE1ADR
FEE1HID provides immediate protection MMR. It does not
require any software keys (see Table 58).
Default Value
0xFFFFFFFF
Access
RW
Name
FEE1CON
Rev. PrA | Page 36 of 92
Address
0xFFFF0E08
Address
0xFFFF0E88
Preliminary Technical Data
ADuC7122
Table 54. FEExSTA MMR Bit Designations
Bit
15:6
5
4
3
2
1
0
Description
Reserved.
Reserved.
Reserved.
Flash/EE interrupt status bit.
Set automatically when an interrupt occurs, that is, when a command is complete and the Flash/EE interrupt enable bit in the
FEExMOD register is set.
Cleared when reading FEExSTA register.
Flash/EE controller busy.
Set automatically when the controller is busy.
Cleared automatically when the controller is not busy.
Command fail.
Set automatically when a command completes unsuccessfully.
Cleared automatically when reading FEExSTA register.
Command complete.
Set by MicroConverter when a command is complete.
Cleared automatically when reading FEExSTA register.
Table 55. FEExMOD MMR Bit Designations
Bit
7:5
4
3
2
1:0
Description
Reserved.
Flash/EE interrupt enable.
Set by user to enable the Flash/EE interrupt. The interrupt occurs when a command is complete.
Cleared by user to disable the Flash/EE interrupt
Erase/write command protection.
Set by user to enable the erase and write commands.
Cleared to protect the Flash/EE memory against erase/write command.
Reserved. Should always be set to 0 by the user.
Flash/EE wait states. Both Flash/EE blocks must have the same wait state value for any change to take effect.
Table 56. Command Codes in FEExCON
Code
0x001
0x011
0x021
0x031
Command
Null
Single read
Single write
Erase/write
0x041
Single verify
0x051
0x061
Single erase
Mass erase
0x07
0x08
0x09
0x0A
0x0B
0x0C
Reserved
Reserved
Reserved
Reserved
Signature
Protect
0x0D
0x0E
0x0F
Reserved
Reserved
Ping
1
Description
Idle state.
Load FEExDAT with the 16-bit data indexed by FEExADR.
Write FEExDAT at the address pointed by FEExADR. This operation takes 50 μs.
Erase the page indexed by FEExADR and write FEExDAT at the location pointed by FEExADR. This operation
takes 20 ms.
Compare the contents of the location pointed by FEExADR to the data in FEExDAT. The result of the comparison
is returned in FEExSTA Bit 1.
Erase the page indexed by FEExADR.
Erase user space. The 2 kB of kernel are protected in Block 0. This operation takes 2.48 sec. To prevent accidental
execution, a command sequence is required to execute this instruction.
Reserved.
Reserved.
Reserved.
Reserved.
Gives a signature of the 64 kB of Flash/EE in the 24-bit FEExSIGN MMR. This operation takes 32,778 clock cycles.
This command can be run only once. The value of FEExPRO is saved and can be removed only with a mass erase
(0x06) or with the key.
Reserved.
Reserved.
No operation, interrupt generated.
The FEExCON register always reads 0x07 immediately after execution of any of these commands.
Rev. PrA | Page 37 of 92
ADuC7122
Preliminary Technical Data
Table 57. FEE0PRO and FEE0HID MMR Bit Designations
Bit
31
30:0
Description
Read Protection.
Cleared by user to protect Block 0.
Set by user to allow reading Block 0.
Write Protection for Page 123 to Page 120, for Page 119 to Page 116, and for Page 0 to Page 3.
Cleared by user to protect the pages in writing.
Set by user to allow writing the pages.
Table 58. FEE1PRO and FEE1HID MMR Bit Designations
Bit
31
30
31:0
Description
Read Protection.
Cleared by user to protect Block 1.
Set by user to allow reading Block 1.
Write Protection for Page 127 to Page 120.
Cleared by user to protect the pages in writing.
Set by user to allow writing the pages.
Write Protection for Page 119 to Page 116 and for Page 0 to Page 3.
Cleared by user to protect the pages in writing.
Set by user to allow writing the pages.
EXECUTION TIME FROM SRAM AND FLASH/EE
This section describes SRAM and Flash/EE access times during
execution of applications where execution time is critical.
Execution from SRAM
Fetching instructions from SRAM takes one clock cycle because
the access time of the SRAM is 2 ns and a clock cycle is 22 ns
minimum. However, if the instruction involves reading or
writing data to memory, one extra cycle must be added if the
data is in SRAM (or three cycles if the data is in Flash/EE), one
cycle to execute the instruction and two cycles to get the 32-bit
data from Flash/EE. A control flow instruction, such as a branch
instruction, takes one cycle to fetch, but it also takes two cycles
to fill the pipeline with the new instructions.
Execution from Flash/EE
Because the Flash/EE width is 16 bits and access time for 16-bit
words is 23 ns, execution from Flash/EE cannot be completed in
one cycle (contrary to a SRAM fetch, which can be completed in
a single cycle when CD bits = 0). Dependent on the instruction,
some dead times may be required before accessing data for any
value of CD bits.
In ARM mode, where instructions are 32 bits, two cycles are
needed to fetch any instruction when CD = 0. In Thumb mode,
where instructions are 16 bits, one cycle is needed to fetch any
instruction.
Timing is identical in both modes when executing instructions
that involve using the Flash/EE for data memory. If the instruction
to be executed is a control flow instruction, an extra cycle is
needed to decode the new address of the program counter and
then four cycles are needed to fill the pipeline. A data processing
instruction involving only core registers doesn’t require any
extra clock cycles, but if it involves data in Flash/EE, an extra
clock cycle is needed to decode the address of the data and two
cycles to get the 32-bit data from Flash/EE. An extra cycle must
also be added before fetching another instruction. Data transfer
instructions are more complex and are summarized in Table 59.
Table 59. Execution Cycles in ARM/Thumb Mode
Instructions
LD
LDH
LDM/PUSH
STR
STRH
STRM/POP
Fetch
Cycles
2/1
2/1
2/1
2/1
2/1
2/1
Dead
Time
1
1
N
1
1
N
Data Access
2
1
2×N
2 × 20 μs
20 μs
2 × N × 20 μs
Dead
Time
1
1
N
1
1
N
With 1 < N ≤ 16, N is the number of bytes of data to load or
store in the multiple load/store instruction. The SWAP instruction
combines an LD and STR instruction with only one fetch,
giving a total of eight cycles plus 40 μs.
Rev. PrA | Page 38 of 92
Preliminary Technical Data
ADuC7122
RESET AND REMAP
Remap Operation
The ARM exception vectors are all situated at the bottom of the
memory array, from Address 0x00000000 to Address 0x00000020,
as shown in Figure 26.
When a reset occurs on the ADuC7122, execution starts
automatically in factory-programmed internal configuration
code. This kernel is hidden and cannot be accessed by user
code. If the ADuC7122 is in normal mode (the BM pin is high), it
executes the power-on configuration routine of the kernel and
then jumps to the reset vector Address 0x00000000 to execute the
user’s reset exception routine. Because the Flash/EE is mirrored at
the bottom of the memory array at reset, the reset interrupt
routine must always be written in Flash/EE.
FFFFFFFFh
0009F800h
kernel
interrupt
service routines
Flash/EE
00080000h
The memory remap from Flash/EE is configured by setting Bit 0 of
the REMAP register. Precautions must be taken to execute this
command from Flash/EE, above Address 0x00080020, and not
from the bottom of the array because this is replaced by the
SRAM.
00041FFFh
interrupt
service routines
SRAM
00040000h
Mirror Space
ARM exception
vector addresses
0x00000020
0x00000000
00000000h
Figure 26. Remap for Exception Execution
By default and after any reset, the Flash/EE is mirrored at the
bottom of the memory array. The remap function allows the
programmer to mirror the SRAM at the bottom of the memory
array, facilitating execution of exception routines from SRAM
instead of from Flash/EE. This means exceptions are executed
twice as fast, with the exception being executed in ARM mode
(32 bits), and the SRAM being 32 bits wide instead of 16-bit
wide Flash/EE memory.
This operation is reversible: the Flash/EE can be remapped at
Address 0x00000000 by clearing Bit 0 of the REMAP MMR.
Precaution must again be taken to execute the remap function
from outside the mirrored area. Any kind of reset remaps the
Flash/EE memory at the bottom of the array.
Reset Operation
There are four types of reset: external reset, power-on reset,
watchdog expiration, and software force reset. The RSTSTA
register indicates the source of the last reset and RSTCLR clears
the RSTSTA register. These registers can be used during a reset
exception service routine to identify the source of the reset.
If RSTSTA is null, the reset was external. Note that when
clearing RSTSTA, all bits that are currently 1 must be cleared.
Otherwise, a reset event occurs.
Table 60. REMAP MMR Bit Designations (Address = 0xFFFF0220, Default Value = 0x00)
Bit
0
Name
Remap
Description
Remap bit.
Set by user to remap the SRAM to Address 0x00000000.
Cleared automatically after reset to remap the Flash/EE memory to address 0x00000000.
Table 61. RSTSTA MMR Bit Designations (Address = 0xFFFF0230, Default Value = 0x0X)
Bit
7:3
2
1
0
Description
Reserved.
Software reset.
Set by user to force a software reset.
Cleared by setting the corresponding bit in RSTCLR.
Watchdog timeout.
Set automatically when a watchdog timeout occurs.
Cleared by setting the corresponding bit in RSTCLR.
Power-on reset.
Set automatically when a power-on reset occurs.
Cleared by setting the corresponding bit in RSTCLR.
Rev. PrA | Page 39 of 92
ADuC7122
Preliminary Technical Data
OTHER ANALOG PERIPHERALS
DAC
The ADuC7122 incorporates 12 buffered 12-bit voltage output
string DACs on-chip. Each DAC has a rail-to-rail voltage output
buffer capable of driving 5 kΩ/100 pF.
Each DAC has three selectable ranges: 0 V to VREF (internal
band gap 2.5 V reference), 0 V to DACREF, and 0 V to Ext Ref.
The signal range is 0 V to AVDD. To note that the DAC can also
operate in interpolation mode.
MMRs Interface
Each DAC is independently configurable through a control
register and a data register. These two registers are identical
for the twelve DACs. Only DACxCON and DACxDAT (see
Table 62 to Table 65) are described in detail in this section.
Figure 27. DAC Configuration
Figure 28. DAC User Functionality
Table 62 DACxCON Registers
Name
DAC0CON
DAC1CON
DAC2CON
DAC3CON
DAC4CON
DAC5CON
DAC6CON
DAC7CON
DAC8CON
DAC9CON
DAC10CON
DAC11CON
Address
0xFFFF0580
0xFFFF0588
0xFFFF0590
0xFFFF0598
0xFFFF05A0
0xFFFF05A8
0xFFFF05B0
0xFFFF05B8
0xFFFF05C0
0xFFFF05C8
0xFFFF05D0
0xFFFF05D8
Default Value
0x100
0x100
0x100
0x100
0x100
0x100
0x100
0x100
0x100
0x100
0x100
0x100
Rev. PrA | Page 40 of 92
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Preliminary Technical Data
ADuC7122
Table 63. DACxCON MMR Bit Designations
Bit
15:9
8
7
6
5
Value
0
1
0
0
0
Name
DACPD
DACBUF_LP
BYP
DACCLK
4
0
DACCLR
3
0
MODE
2
1:0
0
RATE
DACRNx
00
01
10
11
Description
Reserved.
DAC power-down. Set by user to set DACOUTx to tri-state mode.
DAC buffer low power mode. Set by user to place DAC_BUFF in a low power mode.
DAC bypass bit. Set this bit to bypass the DAC buffer. Cleared to buffer the DAC output.
DAC update rate. Set by user to update the DAC using Timer1. Cleared by user to update the DAC using
HCLK (core clock).
DAC clear bit. Set by user to enable normal DAC operation. Cleared by user to reset data register of the
DAC to 0.
Mode bit. Set by user to operate on DAC normal mode and turn off the interpolator clock source. Cleared
by user to enable the interpolation mode.
Rate bit. Set by user to enable the interpolation clock to HCLK/16. Cleared by user to HCLK/32.
DAC range bits.
Int_ref/AGND.
Ext_ref/AGND.
Ext_ref/AGND.
AVDD/AGND.
Table 64. DACxDAT Registers
Name
DAC0DAT
DAC1DAT
DAC2DAT
DAC3DAT
DAC4DAT
DAC5DAT
DAC6DAT
DAC7DAT
DAC8DAT
DAC9DAT
DAC10DAT
DAC11DAT
Address
0xFFFF0584
0xFFFF058C
0xFFFF0594
0xFFFF059C
0xFFFF05A4
0xFFFF05AC
0xFFFF05B4
0xFFFF05BC
0xFFFF05C4
0xFFFF05CC
0xFFFF05D4
0xFFFF05DC
Default Value
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
0x00000000
Table 65. DACxDAT MMR Bit Designations
Bit
31:28
27:16
15:12
11:0
Description
Reserved.
12-bit data for DACx.
Extra bits for Interpolation Mode.
Reserved.
Rev. PrA | Page 41 of 92
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
ADuC7122
Preliminary Technical Data
Using the DACs
AVDD
AVDD – 100mV
The on-chip DAC architecture consists of a resistor string DAC
followed by an output buffer amplifier. The functional equivalent
is shown in Figure 29.
AVDD
VREF
DACREF
R
R
0x00000000
0x0FFF0000
04955-024
100mV
DAC0
R
Figure 30. Endpoint Nonlinearities Due to Amplifier Saturation
R
04955-023
R
Figure 29. DAC Structure
As illustrated in Figure 29, the reference source for each DAC is
user-selectable in software. It can be either AVDD or VREF. In 0-toAVDD mode, the DAC output transfer function spans from 0 V to
the voltage at the AVDD pin. In 0-to-VREF mode, the DAC output
transfer function spans from 0 V to the internal 2.5 V reference,
VREF.
The DAC output buffer amplifier features a true, rail-to-rail
output stage implementation. This means that when unloaded,
each output is capable of swinging to within less than 5 mV of
both AVDD and ground. Moreover, the DAC’s linearity specification
(when driving a 5 kΩ resistive load to ground) is guaranteed
through the full transfer function except codes 0 to 100, and, in
0-to-AVDD mode only, codes 3995 to 4095.
Linearity degradation near ground and VDD is caused by saturation of the output amplifier, and a general representation of its
effects (neglecting offset and gain error) is illustrated in Figure 30.
The dotted line in Figure 30 indicates the ideal transfer function,
and the solid line represents what the transfer function may
look like with endpoint nonlinearities due to saturation of the
output amplifier. Note that Figure 30 represents a transfer function
in 0-to-AVDD mode only. In 0-to-VREF or 0-to-DACREF modes
(with VREF < AVDD or DACREF < AVDD), the lower nonlinearity is
similar. However, the upper portion of the transfer function
follows the ideal line right to the end (VREF in this case, not AVDD),
showing no signs of endpoint linearity errors.
The endpoint nonlinearities conceptually illustrated in
Figure 30 get worse as a function of output loading. The
ADuC7122 data sheet specifications assume a 5 kΩ resistive
load to ground at the DAC output. As the output is forced to
source or sink more current, the nonlinear regions at the top or
bottom (respectively) of Figure 30 become larger. With larger
current demands, this can significantly limit output voltage
swing.
LDO (LOW DROPOUT REGULATOR)
The ADuC7122 contains an integrated LDO which generates
the core supply voltage (LVDD) of approximately 2.6V from the
IOVDD supply. As the LDO is driven from the IOVDD, the
IOVDD supply voltage needs to be greater than 2.7V.
An external compensation capacitor (CT) of 0.47 μF with low
equivalent series resistance (ESR) must be placed very close to
LVDD pin. This capacitor also acts as a storage of charge and
supplies an instantaneous charge required by the core
particularly at positive edge of core clock (HCLK).
The LVDD voltage generated by the LDO is solely for providing
a supply for the ADuC7122. Therefore, users should not use
LVDD pin as the power supply pin for any other chip. Also, it is
recommended that the IOVDD pin have excellent power supply
decoupling, in order to help improve line regulation
performance of the LDO.
The LVDD pin has no reverse battery, current limit or thermal
shutdown protection; therefore, it is essential that users of the
ADuC7122 do not short this pin to ground at anytime during
normal operation or during board manufacture.
Rev. PrA | Page 42 of 92
Preliminary Technical Data
ADuC7122
OSCILLATOR AND PLL—POWER CONTROL
The ADuC7122 integrates a 32.768 kHz oscillator, a clock
divider, and a PLL. The PLL locks onto a multiple (1275) of the
internal oscillator to provide a stable 41.78 MHz clock for the
system. The core can operate at this frequency, or at binary
submultiples of it, to allow power saving. The default core clock
is the PLL clock divided by 8 (CD = 3) or 5.2 MHz. The core
clock frequency can be output on the XCLK pin as described in
Figure 31. Note that when the XCLK pin is used to output the
core clock, the output signal is not buffered and is not suitable
for use as a clock source to an external device without an
external buffer.
Example Source Code
T2LD = 5;
TCON = 0x480;
while ((T2VAL == t2val_old) || (T2VAL >
3)) //ensures timer value loaded
IRQEN = 0x10;
//enable T2 interrupt
PLLKEY1 = 0xAA;
PLLCON = 0x01;
PLLKEY2 = 0x55;
A power-down mode is available on the ADuC7122.
The operating mode, clocking mode, and programmable clock
divider are controlled via two MMRs, PLLCON (see Table 72) and
POWCON (see Table 73). PLLCON controls the operating
mode of the clock system, and POWCON controls the core
clock frequency and the power-down mode.
POWKEY1 = 0x01;
POWCON = 0x27;
// Set Core into Nap mode
POWKEY2 = 0xF4;
In noisy environments, noise can couple to the external crystal
pins, and PLL may lose lock momentarily. A PLL interrupt is
provided in the interrupt controller. The core clock is immediately
halted, and this interrupt is serviced only when the lock is restored.
In case of crystal loss, the watchdog timer should be used. During
initialization, a test on the RSTSTA can determine if the reset
came from the watchdog timer.
EXTERNAL CLOCK SELECTION
To switch to an external clock on P1.4, configure P1.4 in
Mode 2. The external clock can be up to 41.78 MHz, providing
the tolerance is 1%.
Example Source Code
T2LD = 5;
TCON = 0x480;
while ((T2VAL == t2val_old) || (T2VAL >
3)) //ensures timer value loaded
Figure 31. Clocking System
EXTERNAL CRYSTAL SELECTION
IRQEN = 0x10;
//enable T2 interrupt
To switch to an external crystal, users must use the following
procedure:
1.
2.
3.
4.
Enable the Timer2 interrupt and configure it for a timeout
period of >120 μs.
Follow the write sequence to the PLLCON register, setting
the MDCLK bits to 01 and clearing the OSEL bit.
Force the part into nap mode by following the correct write
sequence to the POWCON register.
When the part is interrupted from nap mode by the Timer2
interrupt source, the clock source has switched to the
external clock.
PLLKEY1 = 0xAA;
PLLCON = 0x03; //Select external clock
PLLKEY2 = 0x55;
POWKEY1 = 0x01;
POWCON = 0x27; // Set Core into Nap mode
POWKEY2 = 0xF4;
Rev. PrA | Page 43 of 92
ADuC7122
Preliminary Technical Data
POWER CONTROL SYSTEM
A choice of operating modes is available on the ADuC7122.
Table 66 describes which blocks of the ADuC7122 are powered
on in the different modes and indicates the power-up time. Table
67 gives some typical values of the total current consumption
(analog + digital supply currents) in the different modes,
depending on the clock divider bits when the ADC is turned off.
The ADC is turned off. Note that these values also include current
consumption of the regulator and other parts on the test board on
which these values were measured.
Table 66. Operating Modes
Mode
Active
Pause
Nap
Sleep
Stop
Core
On
Peripherals
On
On
PLL
On
On
On
XTAL/Timer 2/Timer 3
On
On
On
On
XIRQ
On
On
On
On
On
Start-Up/Power-On Time
130 ms at CD = 0
24 ns at CD = 0; 3.06 μs at CD = 7
24 ns at CD = 0; 3.06 μs at CD = 7
1.58 ms
1.7 ms
Table 67. Typical Current Consumption at 25°C
PC[2-0]
000
001
010
011
100
Mode
Active
Pause
Nap
Sleep
Stop
CD = 0
30
22.7
3.8
0.25
0.25
CD = 1
21.2
13.3
3.8
0.25
0.25
CD = 2
13.8
8.5
3.8
0.25
0.25
CD = 3
11
6.1
3.8
0.25
0.25
Rev. PrA | Page 44 of 92
CD = 4
8.1
4.9
3.8
0.25
0.25
CD = 5
7.2
4.3
3.8
0.25
0.25
CD = 6
6.7
4
3.8
0.25
0.25
CD = 7
6.45
3.85
3.8
0.25
0.25
ADuC7122
Preliminary Technical Data
MMRS AND KEYS
Table 73. PLLCON MMR Bit Designations
To prevent accidental programming, a certain sequence must be
followed when writing in the PLLCON and POWCON registers
(see Table 72).
Bit
7:6
5
Value
Name
OSEL
Table 68. PLLKEYx Register
Name
PLLKEY1
PLLKEY2
Address
0xFFFF0410
0xFFFF0418
Default Value
0x0000
0x0000
Access
W
W
4:2
1:0
Table 69. PLLCON Register
Name
PLLCON
Address
0xFFFF0414
Default Value
0x21
Access
R/W
Default Value
0x0000
0x0000
Access
W
W
Table 70. POWKEYx Register
Name
POWKEY1
POWKEY2
Address
0xFFFF0404
0xFFFF040C
Table 74. POWCON MMR Bit Designations
Bit
7
6:4
Address
0xFFFF0408
Default Value
0x0003
Access
R/W
Table 72. PLLCON and POWCON Write Sequence
PLLCON
PLLKEY1 = 0xAA
PLLCON = 0x01
PLLKEY2 = 0x55
POWCON
POWKEY1 = 0x01
POWCON = user value
POWKEY2 = 0xF4
Value
Name
PC
000
001
010
011
Table 71. POWCON Register
Name
POWCON
MDCLK
00
01
10
11
Description
Reserved.
32 kHz PLL Input Selection.
Set by user to use the internal
32 kHz oscillator.
Set by default.
Cleared by user to use the
external 32 kHz crystal.
Reserved.
Clocking modes.
Reserved.
PLL. default configuration.
Reserved.
External clock on P1.4 pin.
100
Others
3
2:0
RSVD
CD
000
001
010
011
100
101
110
111
Rev. PrA | Page 45 of 92
Description
Reserved.
Operating modes.
Active mode.
Pause mode.
Nap.
Sleep mode. IRQ0 to IRQ3 and Timer2
can wake up the ADuC7122.
Stop mode.
Reserved.
Reserved.
CPU clock divider bits.
41.779200 MHz.
20.889600 MHz.
10.444800 MHz.
5.222400 MHz.
2.611200 MHz.
1.305600 MHz.
654.800 kHz.
326.400 kHz.
ADuC7122
Preliminary Technical Data
DIGITAL PERIPHERALS
PWM GENERAL OVERVIEW
HIGH SIDE
(PWM1)
The ADuC7122 integrates a six channel PWM interface. The
PWM outputs can be configured to drive an H-bridge or can be
used as standard PWM outputs. On power up, the PWM outputs
default to H-bridge mode. This ensures that the H-bridge
controlled motor is turned off by default. In standard PWM
mode, the outputs are arranged as three pairs of PWM pins.
Users have control over the period of each pair of outputs and
over the duty cycle of each individual output.
LOW SIDE
(PWM2)
PWM1COM3
PWM1COM2
Table 75. PWM MMRs
Function
PWM Control
Compare Register 1 for PWM Output 1 and Output 2
Compare Register 2 for PWM Output 1 and Output 2
Compare Register 3 for PWM Output 1 and Output 2
Frequency Control for PWM Output 1 and Output 2
Compare Register 1 for PWM Output 3 and Output 4
Compare Register 2 for PWM Output 3 and Output 4
Compare Register 3 for PWM Output 3 and Output 4
Frequency Control for PWM Output 3 and Output 4
Compare Register 1 for PWM Output 5 and Output 6
Compare Register 2 for PWM Output 5 and Output 6
Compare Register 3 for PWM Output 5 and Output 6
Frequency Control for PWM Output 5 and Output 6
PWM Convert Start Control
PWM Interrupt Clear
In all modes, the PWMxCOMx MMRs controls the point at
which the PWM outputs change state. An example of the first pair
of PWM outputs (PWM1 and PWM2) is shown in Figure 32.
06020-044
Name
PWMCON1
PWM1COM1
PWM1COM2
PWM1COM3
PWM1LEN
PWM2COM1
PWM2COM2
PWM2COM3
PWM2LEN
PWM3COM1
PWM3COM2
PWM3COM3
PWM3LEN
PWMCON2
PWMICLR
PWM1COM1
PWM1LEN
Figure 32. PWM Timing
The PWM clock is selectable via PWMCON1 with one of the
following values: UCLK/2, 4, 8, 16, 32, 64, 128, or 256. The
length of a PWM period is defined by PWMxLEN.
The PWM waveforms are set by the count value of the 16-bit
timer and the compare registers contents as shown with the
PWM1 and PWM2 waveforms in Figure 32.
The low-side waveform, PWM2, goes high when the timer
count reaches PWM1LEN, and it goes low when the timer
count reaches the value held in PWM1COM3 or when the
high-side waveform PWM1 goes low.
The high-side waveform, PWM1, goes high when the timer
count reaches the value held in PWM1COM1, and it goes low
when the timer count reaches the value held in PWM1COM2.
In H-bridge mode, HMODE = 1 and Table 76 determine the
PWM outputs.
Table 76. PWMCON1 MMR Bit Designations (Address = 0xFFFF0F80, Default Value = 0x0012)
Bit
15
14
Name
Reserved
SYNC
13
PWM6INV
12
PWM4NV
11
PWM2INV
10
PWMTRIP
9
ENA
8
PWMCP2
Description
This bit is reserved
Enables PWM synchronization.
Set to 1 by the user so that all PWM counters are reset on the next clock edge after the detection of a high-to-low
transition on the SYNC pin.
Cleared by user to ignore transitions on the SYNC pin.
Set to 1 by the user to invert PWM6.
Cleared by user to use PWM6 in normal mode.
Set to 1 by the user to invert PWM4.
Cleared by user to use PWM4 in normal mode.
Set to 1 by the user to invert PWM2.
Cleared by user to use PWM2 in normal mode.
Set to 1 by the user to enable PWM trip interrupt. When the PWMTRIP input is low, the PWMEN bit is cleared and an
interrupt is generated.
Cleared by user to disable the PWMTRIP interrupt.
If HOFF = 0 and HMODE = 1.
Set to 1 by the user to enable PWM outputs.
Cleared by user to disable PWM outputs.
If HOFF = 1 and HMODE = 1, see Table 77.
If not in H-Bridge mode, this bit has no effect.
PWM clock prescaler bits.
Rev. PrA | Page 46 of 92
Preliminary Technical Data
Bit
7
6
Name
PWMCP1
PWMCP0
5
POINV
4
HOFF
3
LCOMP
2
DIR
1
HMODE
0
PWMEN
ADuC7122
Description
Sets UCLK divider.
2.
4.
8.
16.
32.
64.
128.
256.
Set to 1 by the user to invert all PWM outputs.
Cleared by user to use PWM outputs as normal.
High-side off.
Set to 1 by the user to force PWM1 and PWM3 outputs high. This also forces PWM2 and PWM4 low.
Cleared by user to use the PWM outputs as normal.
Load compare registers.
Set to 1 by the user to load the internal compare registers with the values in PWMxCOMx on the next transition of the
PWM timer from 0x00 to 0x01.
Cleared by user to use the values previously stored in the internal compare registers.
Direction control.
Set to 1 by the user to enable PWM1 and PWM2 as the output signals while PWM3 and PWM4 are held low.
Cleared by user to enable PWM3 and PWM4 as the output signals while PWM1 and PWM2 are held low.
Enables H-bridge mode.
Set to 1 by the user to enable H-Bridge mode and Bit 1 to Bit 5 of PWMCON1.
Cleared by user to operate the PWMs in standard mode.
Set to 1 by the user to enable all PWM outputs.
Cleared by user to disable all PWM outputs.
Rev. PrA | Page 47 of 92
ADuC7122
Preliminary Technical Data
Table 77. PWM Output Selection
1
DIR
x
x
0
1
0
1
PWM1
1
1
0
HS1
HS1
1
Table 79. PWMCON2 MMR Bit Designations
PWM Outputs
PWM2 PWM3
1
1
0
1
0
HS1
1
LS
0
LS1
1
1
HS1
PWM4
1
0
LS1
0
1
LS1
HS = high side, LS = low side.
On power-up, PWMCON1 defaults to 0x12 (HOFF = 1 and
HMODE = 1). All GPIO pins associated with the PWM are
configured in PWM mode by default (see Table 78).
Table 78. Compare Register
Name
PWM1COM1
PWM1COM2
PWM1COM3
PWM2COM1
PWM2COM2
PWM2COM3
PWM3COM1
PWM3COM2
PWM3COM3
Address
0xFFFF0F84
0xFFFF0F88
0xFFFF0F8C
0xFFFF0F94
0xFFFF0F98
0xFFFF0F9C
0xFFFF0FA4
0xFFFF0FA8
0xFFFF0FAC
Default Value
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
0x00
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
The PWM trip interrupt can be cleared by writing any value to
the PWMICLR MMR. Note that when using the PWM trip
interrupt, users should make sure that the PWM interrupt
has been cleared before exiting the ISR. This prevents
generation of multiple interrupts.
PWM CONVERT START CONTROL
The PWM can be configured to generate an ADC convert start
signal after the active low side signal goes high. There is a programmable delay between when the low-side signal goes high and
the convert start signal is generated.
(Address = 0xFFFF0FB4, Default Value = 0x00)
Bit Value Name Description
7
CSEN
Set to 1 by the user to enable the PWM
to generate a convert start signal.
Cleared by user to disable the PWM
convert start signal.
3:0
CSD3
Convert start delay. Delays the convert
start signal by a number of clock pulses.
CSD2
CSD1
CSD0
0000
4 clock pulses.
0001
8 clock pulses.
0010
12 clock pulses.
0011
16 clock pulses.
0100
20 clock pulses.
0101
24 clock pulses.
0110
28 clock pulses.
0111
32 clock pulses.
1000
36 clock pulses.
1001
40 clock pulses.
1010
44 clock pulses.
1011
48 clock pulses.
1100
52 clock pulses.
1101
56 clock pulses.
1110
60 clock pulses.
1111
64 clock pulses.
When calculating the time from the convert start delay to the
start of an ADC conversion, the user needs to take account of
internal delays. The example below shows the case for a delay of
four clocks. One additional clock is required to pass the convert
start signal to the ADC logic. Once the ADC logic receives the
convert start signal an ADC conversion begins on the next
ADC clock edge (see Figure 33).
This is controlled via the PWMCON2 MMR. If the delay
selected is higher than the width of the PWM pulse, the
interrupt remains low.
UCLOCK
LOW SIDE
COUNT
PWM SIGNAL
TO CONVST
06020-045
PWMCOM1 MMR
ENA HOFF POINV
0
0
x
x
1
x
1
0
0
1
0
0
1
0
1
1
0
1
SIGNAL PASSED
TO ADC LOGIC
Figure 33. ADC Conversion
Rev. PrA | Page 48 of 92
Preliminary Technical Data
ADuC7122
GENERAL-PURPOSE I/O
The ADuC7122 provides 32 general-purpose, bidirectional I/O
(GPIO) pins. All I/O pins are 5 V tolerant, meaning that the
GPIOs support an input voltage of 5 V. In general, many of the
GPIO pins have multiple functions (see Table 82). By default, the
GPIO pins are configured in GPIO mode.
Table 82. GPIO Pin Function Designations1
Port
0
All GPIO pins have an internal pull-up resistor (of about 100
kΩ) and their drive capability is 1.6 mA. Note that a maximum
of 20 GPIO can drive 1.6 mA at the same time. The 32 GPIOs
are grouped in four ports: Port 0 to Port 3. Each port is controlled by four or five MMRs, with x representing the port number.
P0.2
Table 80. GPxCON Register
Name
GP0CON
GP1CON
GP2CON
GP3CON
Address
0xFFFF0D00
0xFFFF0D04
0xFFFF0D08
0xFFFF0D0C
Default Value
0x00000000
0x00000000
0x00000000
0x11111111
Access
R/W
R/W
R/W
R/W
The input level of any GPIO can be read at any time in the
GPxDAT MMR, even when the pin is configured in a mode
other than GPIO. The PLA input is always active.
1
2
When the ADuC7122 parts enter a power-saving mode, the
GPIO pins retain their state.
GPxCON is the Port x control register, and it selects the
function of each pin of Port x, as described in Table 82.
Table 81. GPxCON MMR Bit Designations
Bit
31:30
29:28
27:26
25:24
23:22
21:20
19:18
17:16
15:14
13:12
11:10
9:8
7:6
5:4
3:2
1:0
Description
Reserved
Select function of Px.7 pin
Reserved
Select function of Px.6 pin
Reserved
Select function of Px.5 pin
Reserved
Select function of Px.4 pin
Reserved
Select function of Px.3 pin
Reserved
Select function of Px.2 pin
Reserved
Select function of Px.1 pin
Reserved
Select function of Px.0 pin
Pin
P0.0
P0.1
3
1
P0.3
P0.4
P0.5
P0.6
P0.7
P1.0
P1.1
P1.4
P1.5
P1.6
P1.7
P2.0
P2.1
P2.2
P2.3
P2.4
P2.5
P2.6
P2.7
P3.0
P3.1
P3.2
P3.3
P3.4
P3.5
P3.6
P3.7
Configuration (see GPxCON)
01
10
SCL1
N/A
SDA1
JTAG
disabled
GPIO
SPICLK
JTAG
disabled
GPIO
SPIMISO SYNC
GPIO
SPIMOSI TRIP
CONVST
GPIO
SPICS
GPIO
MRESET N/A
GPIO
TRST
N/A
GPIO
SIN
SCL2
GPIO
SOUT
SDA2
GPIO
PWM1
XCLK
GPIO
PWM2
N/A
GPIO
N/A
N/A
GPIO
N/A
N/A
GPIO/IRQ0 N/A
N/A
GPIO/IRQ1 N/A
N/A
GPIO
N/A
N/A
GPIO/IRQ2 N/A
N/A
GPIO
PWM5
N/A
GPIO
PWM6
N/A
GPIO/IRQ3 N/A
N/A
GPIO
N/A
N/A
GPIO
N/A
N/A
GPIO
N/A
N/A
GPIO/IRQ4 PWM3
N/A
GPIO/IRQ5 PWM4
N/A
GPIO
N/A
N/A
GPIO
N/A
N/A
GPIO
N/A
N/A
GPIO
N/A
N/A
00
GPIO
GPIO
N/A means no secondary function exists.
Rev. PrA | Page 49 of 92
11
PLAI[5]
PLAI[4]
PLAO[13]
PLAO[12]
PLAI[11]
PLAI[10]
PLAI[2]
PLAI[3]
PLAI[7]
PLAI[1]
PLAI[8]
PLAI[9]
PLAO[5]
PLAO[4]
PLAI[13]
PLAI[12]
PLAI[1]
PLAI[14]
PLAO[7]
PLAO[6]
PLAI[15]
PLAI[0]
PLAO[0]
PLAO[1]
PLAO[2]
PLAO[3]
PLAO[8]
PLAO[9]
PLAO[10]
PLAO[11]
ADuC7122
Preliminary Technical Data
Table 83. GPxPAR Register
Name
GP0PAR
GP1PAR
GP2PAR
GP3PAR
Address
0xFFFF0D2C
0xFFFF0D3C
0xFFFF0D4C
0xFFFF0D5C
Table 87. GPxSET Register
Default Value
0x20000000
0x00000000
0x00000000
0x00222222
Access
RW
RW
RW
RW
GPxPAR programs the parameters for Port 0, Port 1, Port 2 and
Port 3. Note that the GPxDAT MMR must always be written
after changing the GPxPAR MMR.
Table 84. GPxPAR MMR Bit Designations
Bit
31:29
28
27:25
24
23:21
20
19:17
16
15:13
12
11:9
8
7:5
4
3:1
0
Description
Reserved
Pull-up disable Px.7 pin
Reserved
Pull-up disable Px.6 pin
Reserved
Pull-up disable Px.5 pin
Reserved
Pull-up disable Px.4 pin
Reserved
Pull-up disable Px.3 pin
Reserved
Pull-up disable Px.2 pin
Reserved
Pull-up disable Px.1 pin
Reserved
Pull-up disable Px.0 pin
Name
GP0SET
GP1SET
GP2SET
GP3SET
Address
0xFFFF0D20
0xFFFF0D30
0xFFFF0D40
0xFFFF0D50
Default Value
0x000000XX
0x000000XX
0x000000XX
0x000000XX
Bit
31: 24
23:16
15: 0
Description
Reserved.
Data Port x Set Bit.
Set to 1 by user to set bit on Port x; also sets the
corresponding bit in the GPxDAT MMR.
Cleared to 0 by user; does not affect the data out.
Reserved.
GPxCLR Register
Name
GP0CLR
GP1CLR
GP2CLR
GP3CLR
Address
0xFFFF0D28
0xFFFF0D38
0xFFFF0D48
0xFFFF0D58
Default Value
0x000000XX
0x000000XX
0x000000XX
0x000000XX
Access
W
W
W
W
GPxCLR is a data clear Port x register.
Table 89. GPxCLR MMR Bit Designations
Bit
31:24
23:16
Access
R/W
R/W
R/W
R/W
15:0
Table 86. GPxDAT MMR Bit Designations
23:16
15:8
7:0
Access
W
W
W
W
Table 88. GPxSET MMR Bit Designations
GPxDAT is a Port x configuration and data register. It configures
the direction of the GPIO pins of Port x, sets the output value
for the pins configured as output, and receives and stores the
input value of the pins configured as input.
Bit
31:24
Default Value
0x000000XX
0x000000XX
0x000000XX
0x000000XX
GPxSET is a data set Port x register.
Table 85. GPxDAT Register
Name
GP0DAT
GP1DAT
GP2DAT
GP3DAT
Address
0xFFFF0D24
0xFFFF0D34
0xFFFF0D44
0xFFFF0D54
Description
Direction of the Data.
Set to 1 by user to configure the GPIO pin as an output.
Cleared to 0 by user to configure the GPIO pin as an
input.
Port x Data Output.
Reflect the state of Port x pins at reset (read only).
Port x Data Input (Read Only).
Rev. PrA | Page 50 of 92
Description
Reserved.
Data Port x Clear Bit.
Set to 1 by user to clear bit on Port x; also clears
the corresponding bit in the GPxDAT MMR.
Cleared to 0 by user; does not affect the data out.
Reserved.
Preliminary Technical Data
ADuC7122
Open collector functionality is available on the following GPIO
pins: P1.7, P1.6, port 2 and port 3.
Table 90. GPxOCE MMR Bit Designations
Bit
31:8
7
6
5
4
3
2
1
0
Description
Reserved.
GPIO Px.7 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open collector
GPIO Px.6 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
GPIO Px.5 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
GPIO Px.4 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
GPIO Px.3 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
GPIO Px.2 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
GPIO Px.1 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
GPIO Px.0 open-collector enable
Set to 1 by the user to enable open-collector
Set to 0 by the user to disable open-collector
Rev. PrA | Page 51 of 92
ADuC7122
Preliminary Technical Data
UART SERIAL INTERFACE
The ADuC7122 features a 16450-compatible UART.
The UART is a full-duplex, universal, asynchronous
receiver/transmitter. A UART performs serial-to-parallel
conversion on data characters received from a peripheral
device, and parallel-to-serial conversion on data characters
received from the ARM7TDMI. The UART features a fractional
divider that facilitates high accuracy baud rate generation and a
network addressable mode. The UART functionality is available
on the P1.0 and P1.1 pins of the ADuC7122.
Calculation of the baud rate using fractional divider is as
follows:
Baud Rate 
M
41.78 MHz
16  DL  2  ( M 
For example, generation of 19,200 baud
M
41.78 MHz
N

2048 19200  16  67  2
BAUD RATE GENERATION
M
N
 1.015
2048
Normal 450 UART Baud Rate Generation
where:
M = 1.
N = 0.015 × 2048 = 30.
Baud Rate 
The baud rate is a divided version of the core clock using the
value in COMDIV0 and COMDIV1 MMRs (16-bit value, DL).
The standard baud rate generator formula is
Baud rate 
(1)
16  2  DL
Actual Baud Rate
9600
19,200
118,691
% Error
0%
0%
3%
ADuC7122 Fractional Divider
The fractional divider combined with the normal baud rate
generator allows the generating of a wider range of more
accurate baud rates.
/2
FBEN
/16DL
UART
/(M + N/2048)
06020-048
CORE
CLOCK

16  67  2  1 
30
2048

UART REGISTER DEFINITION
The UART interface consists of the following ten registers:
Table 91. Baud Rate Using the Standard Baud Rate Generator
DL
0x88
0x44
0x0B
41.78 MHz
where Baud Rate = 19,219 bps.
41.78 MHz
Table 91 lists common baud rate values.
Baud Rate
9600
19,200
115,200
(2)
41.78 MHz
N

2048 Baud Rate  16  DL  2
The serial communication adopts an asynchronous protocol
that supports various word length, stop bits, and parity generation options selectable in the configuration register.
The ADuC7122 features two methods of generating the UART
baud rate: normal 450 UART baud rate generation and
ADuC7122 fractional divider.
N
)
2048
COMTX: 8-bit transmit register
COMRX: 8-bit receive register
COMDIV0: divisor latch (low byte)
COMDIV1: divisor latch (high byte)
COMCON0: line control register
COMCON1: line control register
COMSTA0: line status register
COMIEN0: interrupt enable register
COMIID0: interrupt identification register
COMDIV2: 16-bit fractional baud divide register
COMTX, COMRX, and COMDIV0 share the same address
location. COMTX and COMRX can be accessed when Bit 7 in
the COMCON0 register is cleared. COMDIV0 can be accessed
when Bit 7 of COMCON0 is set.
Figure 34. Baud Rate Generation Options
Rev. PrA | Page 52 of 92
UART TX Register
UART Divisor Latch Register 1
Write to this 8-bit register to transmit data using the UART.
Name:
COMTX
This 8-bit register contains the most significant byte of the
divisor latch that controls the baud rate at which the UART
operates.
Address:
0xFFFF0800
Name:
COMDIV1
Access:
Write only
Address:
0xFFFF0804
UART RX Register
Default Value:
0x00
This 8-bit register is read from to receive data transmitted using
the UART.
Access:
Read/write
Name:
COMRX
UART Control Register 0
Address:
0xFFFF0800
This 8-bit register controls the operation of the UART in
conjunction with COMCON1.
Default Value:
0x00
Name:
COMCON0
Access:
Read only
Address:
0xFFFF080C
UART Divisor Latch Register 0
Default Value:
0x00
This 8-bit register contains the least significant byte of the
divisor latch that controls the baud rate at which the UART
operates.
Access:
Read/write
Name:
COMDIV0
Address:
0xFFFF0800
Default Value:
0x00
Access:
Read/write
Rev. PrA | Page 53 of 92
ADuC7122
Preliminary Technical Data
Table 92. COMCON0 MMR Bit Designations
Bit
7
Name
DLAB
6
BRK
5
SP
4
EPS
3
PEN
2
STOP
1 to 0
WLS
Description
Divisor latch access.
Set by user to enable access to COMDIV0 and COMDIV1 registers.
Cleared by user to disable access to COMDIV0 and COMDIV1 and enable access to COMRX,
COMTX, and COMIEN0.
Set break.
Set by user to force TxD to 0.
Cleared to operate in normal mode.
Stick parity. Set by user to force parity to defined values.
1 if EPS = 1 and PEN = 1.
0 if EPS = 0 and PEN = 1.
Even parity select bit.
Set for even parity.
Cleared for odd parity.
Parity enable bit.
Set by user to transmit and check the parity bit.
Cleared by user for no parity transmission or checking.
Stop bit.
Set by the user to transmit 1.5 stop bits if the word length is 5 bits, or 2 stop bits if the word length
is 6, 7, or 8 bits. The receiver checks the first stop bit only, regardless of the number of stop bits
selected.
Cleared by the user to generate one stop bit in the transmitted data.
Word length select.
00 = 5 bits.
01 = 6 bits.
10 = 7 bits.
11 = 8 bits.
UART Control Register 1
Table 93. COMCON1 MMR Bit Designations
This 8-bit register controls the operation of the UART in
conjunction with COMCON0.
Bit
7:5
4
Name:
COMCON1
Address:
0xFFFF0810
Default Value:
0x00
Access:
Read/write
Name
LOOPBACK
3:2
1
RTS
0
DTR
Rev. PrA | Page 54 of 92
Description
Reserved bits. Not used.
Loopback. Set by user to enable loopback
mode. In loopback mode, the TxD is
forced high.
Reserved bits. Not used.
Request to send.
Set by user to force the RTS output to 0.
Cleared by user to force the RTS output to
1.
Data Terminal Ready.
Set by user to force the DTR output to 0.
Cleared by user to force the DTR output
to 1.
ADuC7122
Preliminary Technical Data
UART Status Register 0
Name:
COMSTA0
Address:
0xFFFF0714
Default Value:
0x60
Access:
Read only
Function:
This 8-bit read-only register reflects the current status on the UART.
Table 94. COMSTA0 MMR Bit Designations
Bit
7
6
Name
5
THRE
4
BI
3
FE
2
PE
1
OE
0
DR
TEMT
Description
Reserved.
COMTX and shift register empty status bit.
Set automatically if COMTX and the shift register are empty. This bit indicates that the data has
been transmitted, that is, no more data is present in the shift register.
Cleared automatically when writing to COMTX.
COMTX empty status bit.
Set automatically if COMTX is empty. COMTX can be written as soon as this bit is set, the previous
data might not have been transmitted yet and can still be present in the shift register.
Cleared automatically when writing to COMTX.
Break indicator.
Set when SIN is held low for more than the maximum word length.
Cleared automatically.
Framing error.
Set when the stop bit is invalid.
Cleared automatically.
Parity error.
Set when a parity error occurs.
Cleared automatically.
Overrun error.
Set automatically if data are overwritten before being read.
Cleared automatically.
Data ready.
Set automatically when COMRX is full.
Cleared by reading COMRX.
Rev. PrA | Page 55 of 92
ADuC7122
Preliminary Technical Data
UART Interrupt Enable Register 0
Table 96. COMIID0 MMR Bit Designations
Name:
COMIEN0
Address:
0xFFFF0804
Default value:
0x00
Bits[2:1]
Status
Bits
00
11
Bit 0
NINT
1
0
1
Access:
Read/write
Function:
The 8-bit register enables and disables the
individual UART interrupt sources.
10
0
2
01
0
3
00
0
4
Table 95. COMIEN0 MMR Bit Designations
Bit
7:4
3
2
1
0
Name
EDSSI
ELSI
ETBEI
ERBFI
Description
Reserved. Not used.
Modem Status Interrupt Enable Bit.
Set by user to enable generation of an
interrupt if any of COMSTA0[3:1] are set.
Cleared by user.
RxD Status Interrupt Enable Bit.
Set by the user to enable generation of an
interrupt if any of the COMSTA0[3:1] register
bits are set.
Cleared by the user.
Enable Transmit Buffer Empty Interrupt.
Set by the user to enable an interrupt when the
buffer is empty during a transmission, that is,
when COMSTA[5] is set.
Cleared by the user.
Enable Receive Buffer Full Interrupt.
Set by the user to enable an interrupt when the
buffer is full during a reception.
Cleared by the user.
COMIID0
Address:
0xFFFF0808
Default value:
0x01
Access:
Read only
Function:
This 8-bit register reflects the source of the
UART interrupt.
Definition
No interrupt
Receive line
status
interrupt
Receive
buffer full
interrupt
Transmit
buffer empty
interrupt
Modem
status
interrupt
Clearing
Operation
Read
COMSTA0
Read COMRX
Write data to
COMTX or
read COMIID0
Read
COMSTA1
register
UART Fractional Divider Register
This 16-bit register controls the operation of the fractional
divider for the ADuC7122.
Name:
COMDIV2
Address:
0xFFFF082C
Default value:
0x0000
Access:
Read/write
Table 97. COMDIV2 MMR Bit Designations
Bit
15
Name
FBEN
14:13
12:11
FBM[1:0]
10:0
FBN[10:0]
UART Interrupt Identification Register 0
Name:
Priority
Rev. PrA | Page 56 of 92
Description
Fractional Baud Rate Generator Enable Bit.
Set by the user to enable the fractional
baud rate generator.
Cleared by the user to generate the baud
rate using the standard 450 UART baud rate
generator.
Reserved.
M. If FBM = 0, M = 4. See Equation 2 for the
calculation of the baud rate using a
fractional divider and table 76 for common
baud rate values.
N. See Equation 2 for the calculation of the
baud rate using a fractional divider and
table 76 for common baud rate values.
Preliminary Technical Data
ADuC7122
I2C
The ADuC7122 incorporates two I2C peripherals that can be
separately configured as a fully I2C compatible I2C bus Master
device or, as a fully I2C bus compatible slave device. Because
both peripherals are identical, only one is explained here.
The two pins used for data transfer, SDA and SCL, are configured
in a wired-AND format that allows arbitration in a multimaster
system. These pins require external pull-up resistors. Typical
pull-up values are between 4.7 kΩ and 10 kΩ.
The I2C bus peripheral’s address in the I2C bus system is
programmed by the user. This ID can be modified any time a
transfer is not in progress. The user can configure the interface
to respond to four slave addresses.
The transfer sequence of an I2C system consists of a master
device initiating a transfer by generating a start condition while
the bus is idle. The master transmits the slave device address
and the direction of the data transfer (Read or /Write) during
the initial address transfer. If the master does not lose
arbitration and the slave acknowledges, the data transfer is
initiated. This continues until the master issues a stop
condition and the bus becomes idle.
The I2C peripheral can only be configured as a master or slave
at any given time. The same I2C channel cannot simultaneously
support master and slave modes.







The I2C pins of the ADuC7122 device are P0.0 and P0.1 for
I2C1, and P1.0 and P1.1 for I2C2.
P0.0 and P1.0 are the I2C clock signals and P0.1 and P1.1 are
the I2C data signals. For instance, to configure the I2C1 pins
(SCL1, SDA1), Bit 0 and Bit 4 of the GP0CON register must be
set to 1 to enable I2C mode. Alternatively, to configure the I2C2
pins (SCL2, SDA2), Bit 1 and Bit 5 of the GP0CON register
must be set to 1 to enable I2C mode.
SERIAL CLOCK GENERATION
The I2C master in the system generates the serial clock for a
transfer. The master channel can be configured to operate in
fast mode (400 kHz) or standard mode (100 kHz).
The bit rate is defined in the I2CxDIV MMR as follows:
f SERIAL CLOCK 
fUCLK
(2  DIVH )  (2  DIVL)
where:
fUCLK = clock before the clock divider.
DIVH = the high period of the clock.
DIVL = the low period of the clock.
Thus, for 100 kHz operation
DIVH = DIVL = 0xCF
The I2C interface on the ADuC7122 includes the following
features:

Configuring External pins for I2C functionality
and for 400 kHz
Support for Repeated Start Conditions. In Master mode,
the ADuC7122 can be programmed to generate a Repeated
Start. In Slave mode, the ADuC7122 recognizes Repeated
Start conditions.
In Master and Slave mode, the part recognizes both 7-bit
and 10-bit bus addresses.
In I2C Master mode, the ADuC7122 supports continuous
reads from a single slave up to 512 bytes in a single transfer
sequence.
Clock stretching is supported in both Master and Slave
modes.
In Slave mode, the ADuC7122 can be programmed to
return a “NACK.” This allows the validiation of checksum
bytes at the end of I2C transfers.
Bus arbitration in Master mode is supported.
Internal and external loopback modes are supported for
I2C hardware testing. In loopback mode.
The Transmit and receive circuits in both Master and Slave
mode contain 2-byte FIFOs. Status bits are available to the
user to control these FIFOs.
DIVH = 0x28, DIVL = 0x3C
The I2CxDIV register corresponds to DIVH:DIVL
I2C BUS ADDRESSES
Slave Mode
In slave mode, the registers I2CID0, I2CID1, I2CID2, and
I2CID3 contain the device IDs. The device compares the four
I2CIDx registers to the address byte received from the bus
Master. To be correctly addressed, the 7 MSBs of either ID
register must be identical to that of the 7 MSBs of the first
received address byte. The LSB of the ID registers (the transfer
direction bit) is ignored in the process of address recognition.
The ADuC7122 also supports 10-bit addressing mode. When
Bit 1 of I2CSCON (ADR10EN bit) is set to 1, then one 10-bit
address is supported in slave mode and is stored in registers
I2CID0 and I2CID1. The 10-bit address is derived as follows:
I2CID0[0] is the read/write bit and is not part of the I2C
address.
I2CID0[7:1] = Address Bits[6:0].
I2CID1[2:0] = Address Bits[9:7].
I2CID1[7:3] must be set to 11110b
Rev. PrA | Page 57 of 92
ADuC7122
Preliminary Technical Data
Master Mode
In master mode, the I2CADR0 register is programmed with the
I2C address of the device.
I2C Master Registers
I2C Master Control Register
Name:
I2C0MCTL, I2C1MCTL
In 7-bit address mode, I2CADR0[7:1] are set to the device
address. I2CADR0[0] is the read/write bit.
Address:
0xFFFF0880, 0xFFFF0900
In 10-bit address mode, the 10-bit address is created as follows:
Default value:
0x0000, 0x0000
I2CADR0[7:3] must be set to 11110b.
Access:
Read/write
Function:
This 16-bit MMR configures I2C peripheral in
master mode.
I2CADR0[2:1] = Address Bits[9:8].
I2CADR1[7:0] = Address Bits[7:0].
I2CADR0[0] is the read/write bit.
I2C REGISTERS
The I2C peripheral interfaces consists of a number of MMRs.
These are described in the following section.
Table 98. I2CxMCTL MMR Bit Designations
Bit
15:9
8
Name
7
I2CNACKENI
6
I2CALENI
5
I2CMTENI
4
I2CMRENI
3
I2CMSEN
2
I2CILEN
1
I2CBD
0
I2CMEN
I2CMCENI
Description
Reserved. These bits are reserved and should not be written to
I2C transmission complete Interrupt Enable bit
Set this bit to enable an interrupt on detecting a Stop condition on the I2C bus.
Clear this interrupt source.
I2C NACK received Interrupt enable bit.
Set this bit to enable interrupts when the I2C master receives a NACK.
Clear this interrupt source.
I2C Arbitration lost Interrupt Enable bit..
Set this bit to enable interrupts when the I2C master has lost in trying to gain control of the I2C bus.
Clear this interrupt source.
I2C Transmit Interrupt Enable bit.
Set this bit to enable interrupts when the I2C master has transmitted a byte
Clear this interrupt source.
I2C Receive Interrupt Enable bit.
Set this bit to enable interrupts when the I2C master receives data
Cleared by user to disable interrupts when the I2C master is receiving data
I2C Master SCL stretch Enable bit.
Set this bit to 1 to enable Clock stretching. When SCL is low, setting this bit will force the device to hold SCL low
until
I2CMSEN is cleared. If SCL is high, setting this bit will force the device to hold SCL low after the next falling edge.
Clear this bit to disable clock stretching.
I2C Internal Loopback Enable
Set this bit to enable loopback test mode. In this mode, the SCL and SDA signals are connected internally to their
Respective input signals.
Cleared by user to disable Loopback mode.
I2C Master Backoff Disable bit
Set this bit to allow the device to compete for control of the bus even if another device is currently
driving a Start Condition
Clear this bit to back off until the I2C bus becomes free.
I2C Master Enable bit.
Set by user to enable I2C Master mode.
Cleared disable I2C Master mode.
Rev. PrA | Page 58 of 92
Preliminary Technical Data
ADuC7122
I2C Master Status Register
Name:
I2C0MSTA , I2C1MSTA
Address:
0xFFFF0884, 0xFFFF0904
Default value:
0x0000, 0x0000
Access:
Read
Function:
This 16-bit MMR is I2C status register in master mode.
Table 99 I2CxMSTA MMR Bit Designations
Bit
15:11
10
Name
9
I2CMRxFO
8
I2CMTC
7
I2CMNA
6
I2CMBUSY
5
I2CAL
4
I2CMNA
3
I2CMRXQ
2
I2CMTXQ
1:0
I2CMTFSTA
I2CBBUSY
Description
Reserved. These bits are reserved.
I2C bus busy status bit.
This bit is set to 1 when a Start condition is detected on the I2C bus.
This bit is cleared when a Stop condition is detected on the bus
Master Rx FIFO overflow.
This bit is set to 1 when a byte is written to the Rx FIFO when it is already full.
This bit will be cleared in all other conditions.
I2C transmission complete status bit.
This bit is set to 1 when a transmission is complete between the Master and the Slave it was communicating with.
If the I2CMCENI bit in I2CxMCTL is set, an interrupt will be generated when this bit is set.
Clear this interrupt source.
I2C master NACK data bit
This bit will be set to 1 when a NACK condition is received by the Master in response to a Data write transfer.
If the I2CNACKENI bit in I2CxMCTL is set, an interrupt will be generated when this bit is set.
This bit will be cleared in all other conditions.
I2C master busy status bit
Set to 1 when the Master is busy processing a transaction.
Cleared if the Master is ready or if another Master device has control of the bus
I2C arbitration lost status bit..
This bit is set to 1 when the I2C master has lost in trying to gain control of the I2C bus.
If the I2CALENI bit in I2CxMCTL is set, an interrupt will be generated when this bit is set.
This bit will be cleared in all other conditions.
I2C master NACK address bit
This bit will be set to 1 when a NACK condition is received by the Master in response to an Address.
If the I2CNACKENI bit in I2CxMCTL is set, an interrupt will be generated when this bit is set.
This bit will be cleared in all other conditions.
I2C master receive request bit
This bit is set to 1 when data enters the Rx FIFO. If the I2CMRENI in I2CxMCTL is set, an interrupt will be generated.
This bit will be cleared in all other conditions.
I2C master transmit request bit
This bit will go high if the Tx FIFO is empty or only contains 1 byte and the master has transmitted an address +
write. If the I2CMTENI bit in I2CxMCTL is set, an interrupt will be generated when this bit is set.
This bit will be cleared in all other conditions.
I2C master Tx FIFO status bits.
00 = I2C master Tx FIFO empty
01 = 1 byte in master Tx FIFO
10 = 1 byte in master Tx FIFO
11 = I2C Master Tx FIFO Full.
Rev. PrA | Page 59 of 92
ADuC7122
Preliminary Technical Data
I2C Master Receive Register
I2C Master Read Count Register
Name:
I2C0MRX , I2C1MRX
Name:
I2C0MCNT0, I2C1MCNT0
Address:
0xFFFF0888, 0xFFFF0908
Address:
0xFFFF0890, 0xFFFF0910
Default Value:
0x00, 0x00
Default Value:
0x0000, 0x0000
Access:
Read only
Access:
Read/write
Function:
This 8-bit MMR is the I2C master receive
register.
Function:
This 16-bit MMR holds the required number
of bytes when the master begins a read
sequence from a slave device.
I2C Master Transmit Register
I2C Master Current Read Count Register
Name:
I2C0MTX, I2C1MTX
Address:
0xFFFF088C 0xFFFF090C
Default Value:
0x00, 0x00
Access:
Write only
Function:
This 8-bit MMR is the I2C master transmit
register.
Name:
I2C0MCNT1I2C1MCNT1
Address:
0xFFFF0894, 0xFFFF0914
Default value:
0x00, 0x00
Access:
Read
Function:
This 8-bit MMR holds the number of bytes
received so far during a read sequence with a
slave device.
Table 100. I2CxMCNT0 MMR Bit Descriptions (Address = 0xFFFF0890, 0xFFFF0910, Default value = 0x0000)
Bit
15:9
8
Name
7:0
I2CRCNT
I2CRECNT
Description
Reserved.
Set this bit if greater than 256 bytes are required from the slave.
Clear this bit when reading 256 bytes or less.
These 8 bits hold the number of bytes required during a slave read sequence, minus 1. If only a single byte is
required, these bits should be set to 0.
Rev. PrA | Page 60 of 92
Preliminary Technical Data
ADuC7122
I2C Address 0 Register
I2C Master Clock Control Register
Name:
I2C0ADR0, I2C1ADR0
Name:
I2C0DIV, I2C1DIV
Address:
0xFFFF0898, 0xFFFF0918
Address:
0xFFFF08A4, 0xFFFF0924
Default value:
0x00, 0x00
Default Value:
0x1F1F, 0x1F1F
Access:
Read/write
Access:
Read/write
Function:
This 8-bit MMR holds the 7-bit slave address +
the read/write bit when the master begins
communicating with a slave.
Function:
This MMR controls the frequency of the I2C
clock generated by the master on to the SCL
pin. For further details, see I2C initial section.
I2C Address 1 Register
Name:
I2C0ADR1, I2C1ADR1
Address:
0xFFFF089C , 0xFFFF091C
Default value:
0x00, 0x00
Access:
Read/write
Function:
This 8-bit MMR is used in 10-bit addressing
mode only. This register contains the least
significant byte of the address.
Table 101. I2CxADR0 MMR in 7-Bit Address Mode (Address = 0xFFFF0898, 0xFFFF0918, Default Value = 0x00)
Bit
7:1
0
Name
I2CADR
R/W
Description
These bits contain the 7-bit address of the required slave device.
Bit 0 is the read/write bit.
When this bit = 1, a read sequence is requested.
When this bit = 0, a write sequence is requested.
Table 102. I2CxADR0 MMR in 10-Bit Address Mode
Bit
7:3
2:1
0
Name
I2CMADR
R/W
Description
These bits must be set to [11110b] in 10-bit address mode.
These bits contain ADDR[9:8] in 10-bit addressing mode.
Read/write bit.
When this bit = 1, a read sequence is requested.
When this bit = 0, a write sequence is requested.
Table 103. I2CxADR1 MMR in 10-Bit Address Mode
Bit
7:0
Name
I2CLADR
Description
These bits contain ADDR[7:0] in 10-bit addressing mode.
Table 104. I2CxDIV MMR
Bit
15:8
7:0
Name
DIVH
DIVL
Description
These bits control the duration of the High period of SCL.
These bits control the duration of the low period of SCL.
Rev. PrA | Page 61 of 92
ADuC7122
Preliminary Technical Data
I2C Slave Registers
I2C Slave Control Register
Name:
I2C0SCTL, I2C1SCTL
Address:
0xFFFF08A8, 0xFFFF0928
Default Value:
0x0000, 0x000
Access:
Read/write
Function:
This 16-bit MMR configures the I2C peripheral in slave mode.
Table 105. I2CxSCTL MMR Bit Designations
Bit
15:11
10
Name
9
I2CSRXENI
8
I2CSSENI
7
I2CNACKEN
6
I2CSSEN
5
I2CSETEN
4
I2CGCCLR
3
I2CHGCEN
I2CSTXENI
Description
Reserved bits.
Slave transmit interrupt enable bit.
Set this bit to enable an interrupt after a slave transmits a byte.
Clear this interrupt source.
Slave receive interrupt enable bit.
Set this bit to enable an interrupt after the Slave receives data.
Clear this interrupt source.
I2C stop condition detected interrupt enable bit
Set this bit to enable an interrupt on detecting a Stop condition on the I2C bus.
Clear this interrupt source.
I2C NACK enable bit.
Set this bit to NACK the next byte in the transmission sequence.
Clear this bit to let the Hardware control the ACK/NACK sequence.
I2C slave SCL stretch enable bit.
Set this bit to 1 to enable Clock stretching. When SCL is low, setting this bit will force the device to hold
SCL low until I2CSSEN is cleared. If SCL is high, setting this bit will force the device to hold SCL low
after the next falling edge.
Clear this bit to disable clock stretching.
I2C early transmit interrupt enable bit.
Setting this bit enables a transmit request interrupt just after the positive edge of SCL during the read bit
Transmission.
Clear this bit to enable a transmit request interrupt just after the negative edge of SCL during the Read bit
Transmission.
I2C general call status and ID clear bit.
Writing a 1 to this bit will clear the general call status and ID bits in the I2CxSSTA register.
Clear this bit at all other times.
I2C hardware general call enable.
Hardware general call enable. When this bit and Bit 2 are set, and having received a general call (Address 0x00) and a
data byte, the device checks the contents of the I2CALT against the receive register. If the contents match, the device
has received a hardware general call. This is used if a device needs urgent attention from a master device without
knowing which master it needs to turn to. This is a “to whom it may concern” call. The ADuC7122 watches for these
addresses. The device that requires attention embeds its own address into the message. All masters listen, and the
one that can handle the device contacts its slave and acts appropriately.
The LSB of the I2CxALT register should always be written to 1, as per the I2C January 2000 bus specification.
Set this bit and I2CGCEN to enable Hardware General call recognition in Slave mode.
Clear to disable recognition of Hardware General Call commands.
Rev. PrA | Page 62 of 92
Preliminary Technical Data
Bit
2
Name
I2CGCEN
1
0
Reserved
I2CSEN
ADuC7122
Description
I2C general call enable.
Set this bit to enable the slave device to acknowledge an I2C general call, Address 0x00 (write). The device then
recognizes a data bit. If it receives a 0x06 (reset and write programmable part of the slave address by hardware) as
the data byte, the I2C interface resets as per the I2C January 2000 bus specification. This command can be used to
reset an entire I2C system. If it receives a 0x04 (write programmable part of the slave address by hardware) as the
data byte, the general call interrupt status bit sets on any general call.
The user must take corrective action by reprogramming the device address.
Set this bit to allow the Slave “ACK” I2C General Call commands.
Clear to disable recognition of General Call commands.
Always set this bit = 0.
I2C slave enable bit.
Set by user to enable I2C slave mode.
Clear to disable I2Cslave mode.
I2C Slave Status Registers
Name:
I2C0SSTA, I2C1SSTA
Address:
0xFFFF08AC, 0xFFFF092C
Default Value:
0x0000, 0x0000
Access:
Read/write
Function:
This 16-bit MMR is the I2C status register in slave mode.
Table 106. I2CxSSTA MMR Bit Designations
Bit
15
14
Name
13
I2CREPS
12-11
I2CID[1:0]
10
I2CSS
9:8
I2CGCID[1:0]
I2CSTA
Description
Reserved bit.
This bit is set to 1 if:
A start condition followed by a matching address is detected.
It is also set if a start byte (0x01) is received.
If general calls are enabled and a general call code of 0x00 is received.
This bit is cleared on receiving a stop condition
This bit is set to 1 if a repeated start condition is detected.
This bit is cleared on receiving a stop condition
I2C Address matching register. These bits indicate which I2CxIDx register matches the received address.
00 = received address matches I2CxID0
01 = received address matches I2CxID1
10 = received address matches I2CxID2
11 = received address matches I2CxID3
I2C stop condition after start detected bit.
This bit is set to 1 when a stop condition is detected after a previous start and matching address.
When the I2CSSENI bit in I2CxSCTL is set, an interrupt is generated.
This bit is cleared by reading this register.
I2C general call ID bits
00 = no general call received.
01 = general call reset and program address.
10 = general program address.
11 = general call matching alternative ID
Note that these bits are not cleared by a general call reset command.
Clear these bits by writing a 1 to the I2CGCCLR bit in I2CxSCTL.
Rev. PrA | Page 63 of 92
ADuC7122
Bit
7
Name
I2CGC
6
I2CSBUSY
5
I2CSNA
4
I2CSRxFO
3
I2CSRXQ
2
I2CSTXQ
1
I2CSTFE
0
I2CETSTA
Preliminary Technical Data
Description
I2C general call status bit
This bit is set to 1 if the slave receives a general call command of any type.
If the command received was a reset command, then all registers will return to their default state.
If the command received was a hardware general call, the Rx FIFO holds the 2nd byte of the command and this can
be compared with the I2CxALT register.
Clear this bit by writing a 1 to the I2CGCCLR bit in I2CxSCTL.
I2C slave busy status bit
Set to 1 when the slave receives a start condition
Cleared by hardware if:
The received address does not match any of the I2CxIDx registers
The slave device receives a stop condition.
If a repeated start address does not match any of the I2CxIDx registers
I2C slave NACK data bit
This bit is set to 1 when the slave responded to a bus address with a NACK. This bit is asserted under the following
conditions:
If NACK was returned because there was no data in the Tx FIFO
If the I2CNACKEN bit was set in the I2CxSCTL register.
This bit is cleared in all other conditions.
Slave Rx FIFO overflow.
This bit is set to 1 when a byte is written to the Rx FIFO when it is already full.
This bit is cleared in all other conditions.
I2C slave receive request bit
This bit is set to 1 when the slave’s Rx FIFO is not empty.
This bit causes an interrupt to occur if the I2CSRXENI bit in I2CxSCTL is set.
The Rx FIFO must be read or flushed to clear this bit
I2C slave transmit request bit
This bit is set to 1 when the slave receives a matching address followed by a read.
If the I2CSETEN bit in I2CxSCTL is = 0, this bit goes high just after the negative edge of SCL during the read bit
transmission.
If the I2CSETEN bit in I2CxSCTL is = 1, this bit goes high just after the positive edge of SCL during the read bit
transmission.
This bit causes an interrupt to occur if the I2CSTXENI bit in I2CxSCTL is set.
This bit is cleared in all other conditions.
I2C slave FIFO underflow status bit.
This bit goes high if the Tx FIFO is empty when a master requests data from the slave. This bit is asserted at the
rising edge of SCL during the read bit.
This bit is cleared in all other conditions.
I2C slave early transmit FIFO status bit
If the I2CSETEN bit in I2CxSCTL is = 0, this bit goes high of the slave Tx FIFO is empty.
If the I2CSETEN bit in I2CxSCTL is = 1, this bit goes high just after the positive edge of SCL during the write bit
transmission.
This bit asserts once only for a transfer.
This bit is cleared after being read.
Rev. PrA | Page 64 of 92
Preliminary Technical Data
ADuC7122
I2C Slave Receive Registers
I2C Slave Device ID Registers
Name:
I2C0SRX, I2C1SRX
Name:
I2C0IDx, I2C1IDx
Address:
0xFFFF08B0, 0xFFFF0930
Addresses:
0xFFFF093C = I2C1ID0
Default value:
0x00
0xFFFF08BC = I2C0ID0
Access:
Read
0xFFFF0940 = I2C1ID1
Function:
This 8-bit MMR is the I2C slave receive register.
0xFFFF08C0 = I2C0ID1
0xFFFF0944 = I2C1ID2
I2C Slave Transmit Registers
Name:
I2C0STX, I2C1STX
Address:
0xFFFF08B4, 0xFFFF0934
Default value:
0x00
Access:
Write
Function:
This 8-bit MMR is the I2C slave transmit
register.
0xFFFF08C4 = I2C0ID2
0xFFFF0948 = I2C1ID3
0xFFFF08C8 = I2C0ID3
Default value:
0x00
Access:
Read/write
Function:
These 8-bit MMRs are programmed with I2C
bus IDs of the slave. See the I2C Bus Addresses
section for further details.
I2C Hardware General Call Recognition Registers
Name:
I2C0ALT, I2C1ALT
Address:
0xFFFF08B8, 0xFFFF0938
Default value:
0x00
Access:
Read/write
Function:
This 8-bit MMR is used with hardware general
calls when I2CxSCTL bit 3 is set to 1. This
register is used in cases where a master is
unable to generate an address for a slave, and
instead, the slave must generate the address for
the master.
Rev. PrA | Page 65 of 92
ADuC7122
Preliminary Technical Data
I2C COMMON REGISTERS
I2C FIFO Status Register
Name:
I2C0FSTA, I2C1FSTA
Address:
0xFFFF08CC, 0xFFFF094C
Default value:
0x0000
Access:
Read/write
Function:
These 16-bit MMRs contain the status of the Rx/Tx FIFOs in both master and slave modes.
Table 107. I2CxFSTA MMR Bit Designations
Bit
15:10
9
8
7:6
Name
5:4
I2CMTXSTA
3:2
I2CSRXSTA
1:0
I2CSTXSTA
I2CFMTX
I2CFSTX
I2CMRXSTA
Description
Reserved bits.
Set this bit to 1 to flush the master, Tx FIFO.
Set this bit to 1 to flush the slave, Tx FIFO.
I2C master receive FIFO status bits.
00 = FIFO empty.
01 = byte written to FIFO.
10 = 1 byte in FIFO.
11 = FIFO full.
I2C master transmit FIFO status bits.
00 = FIFO empty.
01 = byte written to FIFO.
10 = 1 byte in FIFO.
11 = FIFO full.
I2C slave receive FIFO status bits.
00 = FIFO empty
01 = byte written to FIFO
10 = 1 byte in FIFO
11 = FIFO full
I2C slave transmit FIFO status bits.
00 = FIFO empty.
01 = byte written to FIFO.
10 = 1 byte in FIFO.
11 = FIFO full.
Rev. PrA | Page 66 of 92
Preliminary Technical Data
ADuC7122
SERIAL PERIPHERAL INTERFACE
The ADuC7122 integrates a complete hardware serial
peripheral interface (SPI) on-chip. SPI is an industry standard,
synchronous serial interface that allows eight bits of data to be
synchronously transmitted and simultaneously received, that is,
full duplex up to a maximum bit rate of 20 Mb.
The SPI port can be configured for master or slave operation
and typically consists of four pins: SPIMISO, SPIMOSI,
SPICLK, and SPI CS.
SPIMISO (MASTER IN, SLAVE OUT) PIN
The SPIMISO pin is configured as an input line in master mode
and an output line in slave mode. The SPIMISO line on the
master (data in) should be connected to the SPIMISO line in
the slave device (data out). The data is transferred as byte wide
(8-bit) serial data, MSB first.
SPIMOSI (MASTER OUT, SLAVE IN) PIN
The SPIMOSI pin is configured as an output line in master
mode and an input line in slave mode. The SPIMOSI line on the
master (data out) should be connected to the SPIMOSI line in
the slave device (data in). The data is transferred as byte wide
(8-bit) serial data, MSB first.
SPICLK (SERIAL CLOCK I/O) PIN
The master serial clock (SPICLK) synchronizes the data being
transmitted and received through the MOSI SPICLK period.
Therefore, a byte is transmitted/received after eight SPICLK
periods. The SPICLK pin is configured as an output in master
mode and as an input in slave mode.
SPI CHIP SELECT (SPI CS INPUT) PIN
In SPI slave mode, a transfer is initiated by the assertion of SPI
CS, which is an active low input signal. The SPI port then
transmits and receives 8-bit data until the transfer is concluded
by deassertion of SPI CS. In slave mode, SPI CS is always an
input.
In SPI master mode, the SPICS is an active low output signal. It
asserts itself automatically at the beginning of a transfer and
deasserts itself upon completion.
CONFIGURING EXTERNAL PINS FOR SPI
FUNCTIONALITY
The SPI pins of the ADuC7122 device are P0[2..4].
P0.5 is the Slave Chip Select pin. In Slave mode, this pin is an
input and must be driven low by the Master. In Master mode,
this pin is an output and will go low at the beginning of a
transfer and high at the end of a transfer.
P0.2 is the SPICLK pin.
P0.3 is the master in, slave out (SPIMISO) pin.
P0.4 is the master out, slave in (SPIMOSI) pin.
To configure P0[2:4] for SPI mode, see the General-Purpose
I/O section.
In master mode, polarity and phase of the clock are controlled
by the SPICON register, and the bit rate is defined in the
SPIDIV register as follows:
f SERIAL CLOCK 
f UCLK
2  (1  SPIDIV)
The maximum speed of the SPI clock is independent on the
clock divider bits.
In Slave mode, the SPICON register must be configured with
the phase and polarity of the expected input clock. The slave
accepts data from an external master up to 10 Mb.
In both master and slave modes, data is transmitted on one edge
of the SPICLK signal and sampled on the other. Therefore, it is
important that the polarity and phase are configured the same
for the master and slave devices.
Rev. PrA | Page 67 of 92
ADuC7122
Preliminary Technical Data
SPI REGISTERS
SPI Status Register
The following MMR registers control the SPI interface: SPISTA,
SPIRX, SPITX, SPIDIV, and SPICON.
Name:
SPISTA
Address:
0xFFFF0A00
Default value:
0x0000
Access:
Read/write
Function:
This 16-bit MMR contains the status of the SPI
interface in both master and slave modes.
Table 108. SPISTA MMR Bit Designations
Bit
15:12
11
Name
10:8
SPIRXFSTA[2:0]
7
SPIFOF
6
SPIRXIRQ
5
SPITXIRQ
4
SPITXUF
3:1
SPITXFSTA[2:0]
0
SPIISTA
SPIREX
Description
Reserved bits.
SPI Rx FIFO excess bytes present. This bit is set when there are more bytes in the Rx FIFO than indicated in the
SPIMDE bits in SPICON
This bit is cleared when the number of bytes in the FIFO is equal or less than the number in SPIRXMDE.
SPI Rx FIFO status bits.
000 = Rx FIFO is empty
001 = 1 valid byte in the FIFO
010 = 2 valid bytes in the FIFO
011 = 3 valid bytes in the FIFO
100 = 4 valid bytes in the FIFO
Clear this bit to disable clock stretching.
SPI Rx FIFO overflow status bit.
Set when the Rx FIFO was already full when new data was loaded to the FIFO. This bit generates an interrupt
except when SPIRFLH is set in SPICON.
Cleared when the SPISTA register is read.
SPI Rx IRQ status bit.
Set when a receive interrupt occurs. This bit is set when SPITMDE in SPICON is cleared and the required
number of bytes have been received.
Cleared when the SPISTA register is read.
SPI Tx IRQ status bit.
Set when a transmit interrupt occurs. This bit is set when SPITMDE in SPICON is set and the required number
of bytes have been transmitted.
Cleared when the SPISTA register is read.
SPI Tx FIFO underflow.
This bit is set when a transmit is initiated without any valid data in the Tx FIFO. This bit generates an interrupt
except when SPITFLH is set in SPICON.
Cleared when the SPISTA register is read.
SPI Tx FIFO status bits.
000 = Tx FIFO is empty.
001 = 1 valid byte in the FIFO.
010 = 2 valid bytes in the FIFO.
011 = 3 valid bytes in the FIFO.
100 = 4 valid bytes in the FIFO.
Clear this bit to enable 7-bit address mode
SPI interrupt status bit.
Set to 1 when an SPI-based interrupt occurs.
Cleared after reading SPISTA.
Rev. PrA | Page 68 of 92
ADuC7122
Preliminary Technical Data
SPIDIV Register
SPIRX Register
Name:
SPIRX
Name:
SPIDIV
Address:
0xFFFF0A04
Address:
0xFFFF0A0C
Default value:
0x00
Default value:
0x1B
Access:
Read
Access:
Write
Function:
This 8-bit MMR is the SPI receive register.
Function:
This 8-bit MMR is the SPI baud rate selection
register.
SPITX Register
SPI Control Register
Name:
SPITX
Address:
0xFFFF0A08
Default value:
0x00
Access:
Write
Function:
This 8-bit MMR is the SPI transmit register.
Name:
SPICON
Address:
0xFFFF0A10
Default value:
0x0000
Access:
Read/write
Function:
This 16-bit MMR configures the SPI peripheral
in both master and slave modes.
Table 109. SPICON MMR Bit Designations
Bit
15:14
Name
SPIMDE
13
SPITFLH
12
SPIRFLH
11
SPICONT
10
SPILP
9
SPIOEN
Description
SPI IRQ mode bits. These bits configure when the Tx/Rx interrupts occur in a transfer.
00 = Tx interrupt occurs when one byte has been transferred. Rx interrupt occurs when one or more bytes have been
received by the FIFO.
01 = Tx interrupt occurs when two bytes has been transferred. Rx interrupt occurs when two or more bytes have been
received by the FIFO.
10 = Tx interrupt occurs when three bytes has been transferred. Rx interrupt occurs when three or more bytes have
been received by the FIFO.
11 = Tx interrupt occurs when four bytes has been transferred. Rx interrupt occurs when the Rx FIFO is full, or four bytes
present
SPI Tx FIFO flush enable bit.
Set this bit to flush the Tx FIFO. This bit does not clear itself and should be toggled if a single flush is required. If this bit
is left high, then either the last transmitted value or 0x00 is transmitted depending on the SPIZEN bit.
Any writes to the Tx FIFO are ignored while this bit is set.
Clear this bit to disable Tx FIFO flushing.
SPI Rx FIFO flush enable bit.
Set this bit to flush the Rx FIFO. This bit does not clear itself and should be toggled if a single flush is required.
If this bit is set all incoming data is ignored and no interrupts are generated.
If set and SPITMDE = 0, a read of the Rx FIFO initiates a transfer.
Clear this bit to disable Rx FIFO flushing.
Continuous transfer enable.
Set by user to enable continuous transfer. In master mode, the transfer continues until no valid data is available in the
Tx register. CS is asserted and remains asserted for the duration of each 8-bit serial transfer until Tx is empty.
Cleared by user to disable continuous transfer. Each transfer consists of a single 8-bit serial transfer. If valid data exists
in the SPITX register, then a new transfer is initiated after a stall period of 1 serial clock cycle.
Loop back enable bit.
Set by user to connect MISO to MOSI and test software.
Cleared by user to be in normal mode.
Slave MISO output enable bit.
Set this bit for MISO to operate as normal.
Clear this bit to disable the output driver on the MISO pin. The MISO pin is open-drain when this bit is clear.
Rev. PrA | Page 69 of 92
ADuC7122
Bit
8
Name
SPIROW
7
SPIZEN
6
SPITMDE
5
SPILF
4
SPIWOM
3
SPICPO
2
SPICPH
1
SPIMEN
0
SPIEN
Preliminary Technical Data
Description
SPIRX overflow overwrite enable.
Set by user, the valid data in the Rx register is overwritten by the new serial byte received.
Cleared by user, the new serial byte received is discarded.
SPI transmit zeros when Tx FIFO is empty.
Set this bit to transmit 0x00 when there is no valid data in the Tx FIFO.
Clear this bit to transmit the last transmitted value when there is no valid data in the Tx FIFO.
SPI transfer and interrupt mode.
Set by user to initiate transfer with a write to the SPITX register. Interrupt only occurs when Tx is empty.
Cleared by user to initiate transfer with a read of the SPIRX register. Interrupt only occurs when Rx is full.
LSB first transfer enable bit.
Set by user, the LSB is transmitted first
Cleared by user, the MSB is transmitted first.
SPI wired or mode enable bit
Set to 1 to enable open-drain data output enable. External pull-ups required on data out pins.
Clear for normal output levels..
Serial clock polarity mode bit.
Set by user, the serial clock idles high
Cleared by user, the serial clock idles low.
Serial clock phase mode bit.
Set by user, the serial clock pulses at the beginning of each serial bit transfer.
Cleared by user, the serial clock pulses at the end of each serial bit transfer.
Master mode enable bit
Set by user to enable master mode
Cleared by user to enable slave mode
SPI enable bit.
Set by user to enable the SPI.
Cleared by user to disable the SPI.
Rev. PrA | Page 70 of 92
ADuC7122
Preliminary Technical Data
PROGRAMMABLE LOGIC ARRAY (PLA)
Table 111. PLAELMx Registers
The ADuC7122 integrates a fully programmable logic array
(PLA) that consists of two, independent but interconnected
PLA blocks. Each block consists of eight PLA elements, giving
each part a total of 16 PLA elements.
Each PLA element contains a two-input look-up table that can
be configured to generate any logic output function based on
two inputs and a flip-flop. This is represented in Figure 35.
0
2
4
A
LOOK-UP
TABLE
3
B
04955-033
1
Figure 35. PLA Element
In total, 32 GPIO pins are available on each ADuC7122 for the
PLA. These include 16 input pins and 16 output pins, which need
to be configured in the GPxCON register as PLA pins before
using the PLA. Note that the comparator output is also included
as one of the 16 input pins.
The PLA is configured via a set of user MMRs. The output(s) of
the PLA can be routed to the internal interrupt system, to the
CONVSTART signal of the ADC, to an MMR, or to any of the 16
PLA output pins.
The two blocks can be interconnected as follows:


Name
PLAELM0
PLAELM1
PLAELM2
PLAELM3
PLAELM4
PLAELM5
PLAELM6
PLAELM7
PLAELM8
PLAELM9
PLAELM10
PLAELM11
PLAELM12
PLAELM13
PLAELM14
PLAELM15
Bit
31:11
10:9
8:7
6
Output of Element 7 (Block 0) can be fed back to the Input 0
of Mux 0 of Element 8 (Block 1)
4:1
Element
8
9
10
11
12
13
14
15
PLA Block 1
Input
P1.4
P1.5
P0.5
P0.4
P2.1
P2.0
P2.3
P2.6
PLA MMRs Interface
The PLA peripheral interface consists of the 21 MMRs
described in the following sections.
Value
0000
0001
0010
0011
0100
0101
0110
0111
1000
1001
1010
1011
1100
1101
1110
1111
Table 110. Element Input/Output
Output
P3.0
P3.1
P3.2
P3.3
P1.7
P1.6
P2.5
P2.4
Access
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
R/W
Table 112. PLAELMx MMR Bit Descriptions
5
PLA Block 0
Input
P2.7
P2.2
P0.6
P0.7
P0.1
P0.0
P1.1
P1.0
Default Value
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
0x0000
PLAELMx are Element 0 to Element 15 control registers. They
configure the input and output mux of each element, select the
function in the look-up table, and bypass/use the flip-flop. See
Table 112 and Table 117.
Output of Element 15 (Block 1) can be fed back to Input 0 of
Mux 0 of Element 0 (Block 0)
Element
0
1
2
3
4
5
6
7
Address
0xFFFF0B00
0xFFFF0B04
0xFFFF0B08
0xFFFF0B0C
0xFFFF0B10
0xFFFF0B14
0xFFFF0B18
0xFFFF0B1C
0xFFFF0B20
0xFFFF0B24
0xFFFF0B28
0xFFFF0B2C
0xFFFF0B30
0xFFFF0B34
0xFFFF0B38
0xFFFF0B3C
Output
P3.4
P3.5
P3.6
P3.7
P0.3
P0.2
P1.3
P1.2
0
Rev. PrA | Page 71 of 92
Description
Reserved.
Mux 0 control (see Table 117).
Mux 1 control (see Table 117).
Mux 2 control. Set by user to select the output
of Mux 0. Cleared by user to select the bit value
from PLADIN.
Mux 3 control. Set by user to select the input
pin of the particular element. Cleared by user to
select the output of Mux 1.
Look-up table control.
0.
NOR.
B AND NOT A.
NOT A.
A AND NOT B.
NOT B.
EXOR.
NAND.
AND.
EXNOR.
B.
NOT A OR B.
A.
A OR NOT B.
OR.
1.
Mux 4 Control. Set by user to bypass the flipflop. Cleared by user to select the flip-flop
(cleared by default).
ADuC7122
Preliminary Technical Data
Table 113. PLACLK Register
Name
PLACLK
Address
0xFFFF0B40
Table 115. PLAIRQ Register
Default Value
0x00
Access
R/W
PLACLK is the clock selection for the flip-flops of Block 0 and
Block 1. Note that the maximum frequency when using the
GPIO pins as the clock input for the PLA blocks is 44 MHz.
Value
000
001
010
011
100
101
Other
3
2:0
000
001
010
011
100
101
Other
Address
0xFFFF0B44
Default Value
0x00000000
PLAIRQ enables IRQ0 and/or IRQ1 and selects the source
of the IRQ.
Bit
15:13
12
Description
Reserved.
Block 1 clock source selection.
GPIO clock on P0.5.
GPIO clock on P0.0.
GPIO clock on P0.7.
HCLK.
External crystal (OCLK) (32.768 kHz).
Timer1 overflow.
Reserved.
Reserved.
Block 0 clock source selection.
GPIO clock on P0.5.
GPIO clock on P0.0.
GPIO clock on P0.7.
HCLK.
External crystal (OCLK) (32.768 kHz).
Timer1 overflow.
Reserved.
Value
11:8
0000
0001
1111
7:5
4
3:0
0000
0001
1111
Description
Reserved.
PLA IRQ1 enable bit. Set by user to enable
IRQ1 output from PLA. Cleared by user to
disable IRQ1 output from PLA.
PLA IRQ1 source.
PLA Element 0.
PLA Element 1.
PLA Element 15.
Reserved.
PLA IRQ0 enable bit. Set by user to enable
IRQ0 output from PLA. Cleared by user to
disable IRQ0 output from PLA.
PLA IRQ0 source.
PLA Element 0.
PLA Element 1.
PLA Element 15.
Table 117. Feedback Configuration
Bit
10:9
8:7
Value
00
01
10
11
00
01
10
11
PLAELM0
Element 15
Element 2
Element 4
Element 6
Element 1
Element 3
Element 5
Element 7
Access
R/W
Table 116. PLAIRQ MMR Bit Descriptions
Table 114. PLACLK MMR Bit Descriptions
Bit
7
6:4
Name
PLAIRQ
PLAELM1 to PLAELM7
Element 0
Element 2
Element 4
Element 6
Element 1
Element 3
Element 5
Element 7
Rev. PrA | Page 72 of 92
PLAELM8
Element 7
Element 10
Element 12
Element 14
Element 9
Element 11
Element 13
Element 15
PLAELM9 to PLAELM15
Element 8
Element 10
Element 12
Element 14
Element 9
Element 11
Element 13
Element 15
Preliminary Technical Data
ADuC7122
PLAADC Register
Name
PLAADC
Address
0xFFFF0B48
Default Value
0x00000000
Access
R/W
PLAADC is the PLA source for the ADC start conversion signal.
Table 118. PLAADC MMR Bit Descriptions
Bit
31:5
4
Value
3:0
0000
0001
1111
Description
Reserved.
ADC start conversion enable bit. Set by user
to enable ADC start conversion from PLA.
Cleared by user to disable ADC start
conversion from PLA.
ADC start conversion source.
PLA Element 0.
PLA Element 1.
PLA Element 15.
PLADIN Register
Name
PLADIN
Address
0xFFFF0B4C
types: a normal interrupt request (IRQ) and a fast interrupt
request (FIQ). All the interrupts can be masked separately.
The control and configuration of the interrupt system is
managed through a number of interrupt-related registers. The
bits in each IRQ and FIQ register represent the same interrupt
source as described in Table 121.
The ADuC7122 contains a vectored interrupt controller (VIC)
that supports nested interrupts up to eight levels. The VIC also
allows the programmer to assign priority levels to all interrupt
sources. Interrupt nesting needs to be enabled by setting the
ENIRQN bit in the IRQCONN register. A number of extra
MMRs are used when the full vectored interrupt controller is
enabled.
IRQSTA/FIQSTA should be saved immediately upon entering
the interrupt service routine (ISR) to ensure that all valid
interrupt sources are serviced.
Table 121. IRQ/FIQ MMRs Bit Designations
Default Value
0x00000000
Access
R/W
PLADIN is a data input MMR for PLA.
Bit
0
1
Description
All interrupts OR’ed
(FIQ only)
Software Interrupt
Table 119. PLADIN MMR Bit Descriptions
Bit
31:16
15:0
2
3
4
Description
Reserved.
Input bit to Element 15 to Element 0.
5
PLADOUT Register
Name
PLADOUT
Address
0xFFFF0B50
Default Value
0x00000000
Access
R
PLADOUT is a data output MMR for PLA. This register is
always updated.
Table 120. PLADOUT MMR Bit Descriptions
Bit
31:16
15:0
Description
Reserved.
Output bit from Element 15 to Element 0.
PLALCK Register
Name
PLALCK
Address
0xFFFF0B54
Default Value
0x00
Access
W
PLALCK is a PLA lock option. Bit 0 is written only once. When
set, it does not allow modifying any of the PLA MMRs, except
PLADIN. A PLA tool is provided in the development system to
easily configure the PLA.
INTERRUPT SYSTEM
There are 27 interrupt sources on the ADuC7122 that are
controlled by the interrupt controller. All interrupts are
generated from the on-chip peripherals, except for the software
interrupt (SWI) which is programmable by the user. The
ARM7TDMI CPU core only recognizes interrupts as one of two
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
Rev. PrA | Page 73 of 92
Timer0
Timer1
Timer2 or wake-up
timer
Timer3 or watchdog
timer
Timer4
Reserved
PSM
Undefined
Flash Control 0
Flash Control 1
ADC
UART
SPI
I2C 0 Master IRQ
I2C 0 Slave IRQ
I2C 1 Master IRQ
I2C 1 Slave IRQ
XIRQ0 (GPIO IRQ0 )
XIRQ1 (GPIO IRQ1)
XIRQ2 (GPIO IRQ2 )
XIRQ3 (GPIO IRQ3)
PWM
XIRQ4 (GPIO IRQ4 )
XIRQ5 (GPIO IRQ5)
PLA IRQ0
PLA IRQ1
Comments
This bit is set if any FIQ is active
User programmable interrupt
source
General-Purpose Timer 0
General-Purpose Timer 1
General-Purpose Timer 2 or
wake-up timer
General-Purpose Timer 3 or
watchdog timer
General-Purpose Timer 4
Reserved
Power Supply Monitor
This bit is not used
Flash controller for Block 0 interrupt
Flash controller for Block 1 interrupt
ADC interrupt source bit
UART interrupt source bit
SPI interrupt source bit
I2C master interrupt source bit
I2C slave interrupt source bit
I2C master interrupt source bit
I2C slave interrupt source bit
External Interrupt 0
External Interrupt 1
External Interrupt 2
External Interrupt 3
PWM Trip interrupt source bit
External Interrupt 4
External Interrupt 5
PLA block 0 IRQ bit
PLA block 1 IRQ bit
ADuC7122
Preliminary Technical Data
IRQ
IRQSTA
The IRQ is the exception signal to enter the IRQ mode of the
processor. It services general-purpose interrupt handling of
internal and external events.
IRQSTA is a read-only register that provides the current
enabled IRQ source status (effectively a logic AND of the
IRQSIG and IRQEN bits). When set to 1, that source generates
an active IRQ request to the ARM7TDMI core. There is no
priority encoder or interrupt vector generation. This function is
implemented in software in a common interrupt handler
routine.
All 32 bits are logically OR’ed to create a single IRQ signal to the
ARM7TDMI core. The four 32-bit registers dedicated to IRQ
follow.
IRQSIG
IRQSIG reflects the status of the different IRQ sources. If a
peripheral generates an IRQ signal, the corresponding bit in
the IRQSIG is set; otherwise, it is cleared. The IRQSIG bits clear
when the interrupt in the particular peripheral is cleared. All
IRQ sources can be masked in the IRQEN MMR. IRQSIG is
read only.
IRQSIG Register
IRQSIG Register
Name:
IRQSTA
Address:
0xFFFF0000
Default value:
0x00000000
Access:
Read only
Name:
IRQSIG
FAST INTERRUPT REQUEST (FIQ)
Address:
0xFFFF0004
Default value:
0x00000000
Access:
Read only
The fast interrupt request (FIQ) is the exception signal to enter
the FIQ mode of the processor. It is provided to service data
transfer or communication channel tasks with low latency. The
FIQ interface is identical to the IRQ interface and provides the
second level interrupt (highest priority). Four 32-bit registers
are dedicated to FIQ: FIQSIG, FIQEN, FIQCLR, and FIQSTA.
IRQEN
IRQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled
to create an IRQ exception. When a bit is set to 0, the corresponding source request is disabled or masked which does not
create an IRQ exception. The IRQEN register cannot be used to
disable an interrupt.
IRQEN Register
Bit 31 to Bit 1 of FIQSTA are logically OR’ed to create the FIQ
signal to the core and to Bit 0 of both the FIQ and IRQ registers
(FIQ source).
The logic for FIQEN and FIQCLR does not allow an interrupt
source to be enabled in both IRQ and FIQ masks. A bit set to 1
in FIQEN clears, as a side effect, the same bit in IRQEN.
Likewise, a bit set to 1 in IRQEN clears, as a side effect, the
same bit in FIQEN. An interrupt source can be disabled in both
IRQEN and FIQEN masks.
Name:
IRQEN
Address:
0xFFFF0008
FIQSIG
Default value:
0x00000000
Access:
Read/write
FIQSIG reflects the status of the different FIQ sources. If a
peripheral generates an FIQ signal, the corresponding bit in
the FIQSIG is set, otherwise it is cleared. The FIQSIG bits are
cleared when the interrupt in the particular peripheral is
cleared. All FIQ sources can be masked in the FIQEN MMR.
FIQSIG is read only.
IRQCLR
IRQCLR is a write-only register that allows the IRQEN register
to clear in order to mask an interrupt source. Each bit that is set
to 1 clears the corresponding bit in the IRQEN register without
affecting the remaining bits. The pair of registers, IRQEN and
IRQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
FIQSIG RegisterPrA
Name:
FIQSIG
Address:
0xFFFF0104
IRQCLR Register
Default value:
0x00000000
Name:
IRQCLR
Access:
Read only
Address:
0xFFFF000C
Default value:
0x00000000
Access:
Write only
Rev. PrA | Page 74 of 92
Preliminary Technical Data
ADuC7122
FIQEN
FIQEN provides the value of the current enable mask. When a
bit is set to 1, the corresponding source request is enabled
to create an FIQ exception. When a bit is set to 0, the corresponding source request is disabled or masked which does not
create an FIQ exception. The FIQEN register cannot be used to
disable an interrupt.
The 32-bit register dedicated to software interrupt is SWICFG
described in Table 122. This MMR allows the control of a
programmed source interrupt.
Table 122. SWICFG MMR Bit Designations
Bit
31 to 3
2
FIQEN Register
Name:
FIQEN
Address:
0xFFFF0108
Default value:
0x00000000
Access:
Read/write
1
0
Description
Reserved.
Programmed Interrupt FIQ. Setting/clearing this bit
corresponds to setting/clearing Bit 1 of FIQSTA and
FIQSIG.
Programmed Interrupt IRQ. Setting/clearing this bit
corresponds to setting/clearing Bit 1 of IRQSTA and
IRQSIG.
Reserved.
Any interrupt signal must be active for at least the minimum
interrupt latency time, to be detected by the interrupt controller
and to be detected by the user in the IRQSTA/FIQSTA register.
FIQCLR
FIQCLR is a write-only register that allows the FIQEN register
to clear in order to mask an interrupt source. Each bit that is set
to 1 clears the corresponding bit in the FIQEN register without
affecting the remaining bits. The pair of registers, FIQEN and
FIQCLR, allows independent manipulation of the enable mask
without requiring an atomic read-modify-write.
PROGRAMMABLE PRIORITY
PER INTERRUPT (IRQP0/IRQP1/IRQP2)
POINTER TO
FUNCTION
(IRQVEC)
IRQ_SOURCE
INTERNAL
ARBITER
LOGIC
FIQ_SOURCE
FIQCLR Register
Name:
FIQCLR
Address:
0xFFFF010C
Default value:
0x00000000
Access:
Write only
INTERRUPT VECTOR
BITS 31-23
UNUSED
BITS 22-7
(IRQBASE)
BITS 6-2 BITS 1-0
HIGHEST
LSBs
PRIORITY
ACTIVE IRQ
Figure 36. Interrupt Structure
FIQSTA
Vectored Interrupt Controller (VIC)
FIQSTA is a read-only register that provides the current enabled
FIQ source status (effectively a logic AND of the FIQSIG and
FIQEN bits). When set to 1, that source generates an active FIQ
request to the ARM7TDMI core. There is no priority encoder
or interrupt vector generation. This function is implemented in
software in a common interrupt handler routine.
FIQSTA Register
The ADUC7122 incorporates an enhanced interrupt control
system or vectored interrupt controller. The vectored interrupt
controller for IRQ interrupt sources is enabled by setting Bit 0
of the IRQCONN register. Similarly, Bit 1 of IRQCONN enables
the vectored interrupt controller for the FIQ interrupt sources.
The vectored interrupt controller provides the following
enhancements to the standard IRQ/FIQ interrupts:
Name:
FIQSTA

Address:
0xFFFF0100
Default value:
0x00000000
Access:
Read only

Programmed Interrupts
Because the programmed interrupts are not maskable, they are
controlled by another register (SWICFG) that writes into both
IRQSTA and IRQSIG registers and/or the FIQSTA and FIQSIG
registers at the same time.

Vectored interrupts—allows a user to define separate
interrupt service routine addresses for every interrupt
source. This is achieved by using the IRQBASE and
IRQVEC registers.
IRQ/FIQ interrupts—can be nested up to eight levels
depending on the priority settings. An FIQ still has a
higher priority than an IRQ. Therefore, if the VIC is
enabled for both the FIQ and IRQ and prioritization is
maximized, then it is possible to have 16 separate interrupt
levels.
Programmable interrupt priorities—using the IRQP0 to
IRQP2 registers, an interrupt source can be assigned an
interrupt priority level value between 1 and 8.
Rev. PrA | Page 75 of 92
ADuC7122
Preliminary Technical Data
VIC MMRs
IRQBASE Register
Priority Registers
IRQP0 Register
The vector base register, IRQBASE, is used to point to the start
address of memory used to store 32 pointer addresses. These
pointer addresses are the addresses of the individual interrupt
service routines.
Name:
IRQP0
Address:
0xFFFF0020
Default value:
0x00000000
Access:
Read and write
Name:
IRQBASE
Address:
0xFFFF0014
Default value:
0x00000000
Access:
Read and write
Table 125. IRQP0 MMR Bit Designations
Bit
31:27
26:24
Name
Reserved
T4PI
23
22:20
Reserved
T3PI
19
18:16
Reserved
T2PI
The IRQ interrupt vector register, IRQVEC points to a memory
address containing a pointer to the interrupt service routine of
the currently active IRQ. This register should only be read when
an IRQ occurs and IRQ interrupt nesting has been enabled by
setting Bit 0 of the IRQCONN register.
15
14:12
Reserved
T1PI
11
10:8
Reserved
T0PI
Name:
IRQVEC
7
6:4
Reserved
SWINTP
Address:
0xFFFF001C
Default value:
0x00000000
3:0
Reserved
Access:
Read only
Table 123. IRQBASE MMR Bit Designations
Bit
31:16
15:0
Type
Read only
R/W
Initial Value
Reserved
0
Description
Always read as 0
Vector base address
IRQVEC Register
IRQP1 Register
Table 124. IRQVEC MMR Bit Designations
Bit
31:23
22:7
6:2
1:0
Type
Read
only
R/W
Read
only
Reserved
Initial
value
0
0
0
0
Description
Reserved bit
A priority level of 0 to 7 can be set for
Timer 4.
Reserved bit
A priority level of 0 to 7 can be set for
Timer 3.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer 2.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer 1.
Reserved bit.
A priority level of 0 to 7 can be set for
Timer 0.
Reserved bit
A priority level of 0 to 7 can be set for the
software interrupt source.
Interrupt 0 cannot be prioritized.
Description
Always read as 0.
IRQBASE register value.
Highest priority IRQ source. This is
a value between 0 to 19
representing the possible interrupt
sources. For example, if the highest
currently active IRQ is Timer 1, then
these bits are [01000].
Reserved bits.
Name:
IRQP1
Address:
0xFFFF0024
Default value:
0x00000000
Access:
Read and write
Rev. PrA | Page 76 of 92
Preliminary Technical Data
ADuC7122
IRQP3 Register
Table 126. IRQP1 MMR Bit Designations
Bit
31
30:28
Name
Reserved
I2C0MPI
27
26:24
23
22:20
19
18:16
Reserved
SPIPI
Reserved
UARTPI
Reserved
ADCPI
15
14:12
Reserved
Flash1PI
11
10:8
Reserved
Flash0PI
7:3
2:0
Reserved
PSMPI
Description
Reserved bit.
A priority level of 0 to 7 can be set for I2C0
master.
Reserved bit.
A priority level of 0 to 7 can be set for SPI.
Reserved bit.
A priority level of 0 to 7 can be set for UART.
Reserved bit.
A priority level of 0 to 7 can be set for the
ADC interrupt source.
Reserved bit.
A priority level of 0 to 7 can be set for the
Flash Block 1 controller interrupt source.
Reserved bit.
A priority level of 0 to 7 can be set for the
Flash Block 0 controller interrupt source.
Reserved bits.
A priority level of 0 to 7 can be set for the
Power supply monitor interrupt source.
IRQP2 Register
Name:
IRQP3
Address:
0xFFFF002C
Default value:
0x00000000
Access:
Read and write
Table 128. IRQP3 MMR Bit Designations
Bit
31:15
14:12
11
10:8
7
6:4
3
2:0
Name
Reserved
PLA1PI
Reserved
PLA0PI
Reserved
IRQ5PI
Reserved
IRQ4PI
Description
Reserved bit.
A priority level of 0 to 7 can be set for PLA0.
Reserved bit.
A priority level of 0 to 7 can be set for PLA0.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ5.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ4.
IRQCONN Register
The IRQCONN register is the IRQ and FIQ control register. It
contains two active bits. The first to enable nesting and
prioritization of IRQ interrupts the other to enable nesting and
prioritization of FIQ interrupts.
Name:
IRQP2
Address:
0xFFFF0028
Default value:
0x00000000
If these bits are cleared, then FIQs and IRQs may still be used
but it is not possible to nest IRQs or FIQs. Neither is it possible
to set an interrupt source priority level. In this default state, an
FIQ does have a higher priority than an IRQ.
Access:
Read and write
Name:
IRQCONN
Table 127. . IRQP2 MMR Bit Designations
Address:
0xFFFF0030
Bit
31
30:28
27
26:24
23
22:20
19
18:16
15
14:12
11
10:8
Name
Reserved
PWMPI
Reserved
IRQ3PI
Reserved
IRQ2PI
Reserved
IRQ1PI
Reserved
IRQ0PI
Reserved
I2C1SPI
Default value:
0x00000000
Access:
Read and write
7
6:4
Reserved
I2C1MPI
3
2:0
Reserved
I2C0SPI
Description
Reserved bit.
A priority level of 0 to 7 can be set for PWM.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ3.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ2.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ1.
Reserved bit.
A priority level of 0 to 7 can be set for IRQ0.
Reserved bit.
A priority level of 0 to 7 can be set for I2C1
slave.
Reserved bit.
A priority level of 0 to 7 can be set for I2C1
master.
Reserved bit.
A priority level of 0 to 7 can be set for I2C0
slave.
Table 129. IRQCONN MMR Bit Designations
Bit
31:2
Name
Reserved
1
ENFIQN
0
ENIRQN
Rev. PrA | Page 77 of 92
Description
These bits are reserved and should not be
written to.
Setting this bit to 1 enables nesting of FIQ
interrupts. Clearing this bit means no nesting
or prioritization of FIQs is allowed.
Setting this bit to 1 enables nesting of IRQ
interrupts. Clearing this bit means no nesting
or prioritization of IRQs is allowed.
ADuC7122
Preliminary Technical Data
IRQSTAN Register
FIQSTAN Register
If IRQCONN.0 is asserted and IRQVEC is read then one of
these bits is asserted. The bit that asserts depend on the priority
of the IRQ. If the IRQ is of Priority 0 then Bit 0 asserts, Priority 1
then Bit 1 asserts, and so forth. When a bit is set in this register,
all interrupts of that priority and lower are blocked.
If IRQCONN.1 is asserted and FIQVEC is read then one of
these bits assert. The bit that asserts depends on the priority of
the FIQ. If the FIQ is of Priority 0 then Bit 0 asserts, Priority 1
then Bit 1 asserts, and so forth.
To clear a bit in this register, all bits of a higher priority must be
cleared first. It is only possible to clear one bit at a time. For
example, if this register is set to 0x09 then writing 0xFF changes
the register to 0x08, and writing 0xFF a second time changes
the register to 0x00.
When a bit is set in this register all interrupts of that priority
and lower are blocked.
Name:
IRQSTAN
To clear a bit in this register all bits of a higher priority must be
cleared first. It is only possible to clear one bit as a time. For
example if this register is set to 0x09 then writing 0xFF changes
the register to 0x08 and writing 0xFF a second time changes the
register to 0x00.
Address:
0xFFFF003C
Name:
FIQSTAN
Default value:
0x00000000
Address:
0xFFFF013C
Access:
Read and write
Default value:
0x00000000
Access:
Read and write
Table 130. IRQSTAN MMR Bit Designations
Bit
31:8
Name
Reserved
7:0
Description
These bits are reserved and should not be
written to.
Setting this bit to 1 enables nesting of FIQ
interrupts. Clearing this bit, means no nesting
or prioritization of FIQs is allowed.
Table 132. FIQSTAN MMR Bit Designations
Bit
31:8
Name
Reserved
7:0
FIQVEC Register
The FIQ interrupt vector register, FIQVEC points to a memory
address containing a pointer to the interrupt service routine of
the currently active FIQ. This register should only be read when
an FIQ occurs and FIQ interrupt nesting has been enabled by
setting Bit 1 of the IRQCONN register.
Name:
FIQVEC
Address:
0xFFFF011C
Default value:
0x00000000
Access:
Read only
Bit
31:23
22:7
6:2
Type
Read only
R/W
1:0
Reserved
0
External Interrupts (IRQ0 to IRQ3)
The ADuC7122 provides up to four external interrupt sources.
These external interrupts can be individually configured as level
or rising/falling edge triggered.
To enable the external interrupt source, first of all, the
appropriate bit must be set in the FIQEN or IRQEN register. To
select the required edge or level to trigger on, the IRQCONE
register must be appropriately configured.
To properly clear an edge based external IRQ interrupt, set the
appropriate bit in the EDGELEVELCLR register.
IRQCONE Register
Table 131. FIQVEC MMR Bit Designations
Initial
Value
0
0
0
Description
These bits are reserved and should not be
written to.
Setting this bit to 1 enables nesting of FIQ
interrupts. Clearing this bit, means no nesting
or prioritization of FIQs is allowed.
Description
Always read as 0.
IRQBASE register value.
Highest priority FIQ source. This is
a value between 0 to 19 represent
the possible interrupt sources. For
example, if the highest currently
active FIQ is Timer 1, then these
bits are 01000.
Reserved bits.
Name:
IRQCONE
Address:
0xFFFF0034
Default value:
0x00000000
Access:
Read and write
Rev. PrA | Page 78 of 92
ADuC7122
Preliminary Technical Data
Table 133. IRQCONEMMR Bit Designations
Bit
31:12
11:10
9:8
7:6
5:4
3:2
1:0
Value
11
10
01
00
11
10
01
00
11
10
01
00
11
10
01
00
11
10
01
00
11
10
01
00
Name
Reserved
IRQ5SRC[1:0]
IRQ4SRC[1:0]
IRQ3SRC[1:0]
IRQ2SRC[1:0]
IRQ1SRC[1:0]
IRQ0SRC[1:0]
Description
These bits are reserved and should not be written to.
External IRQ5 triggers on falling edge.
External IRQ5 triggers on rising edge.
External IRQ5 triggers on low level.
External IRQ5 triggers on high level.
External IRQ4 triggers on falling edge.
External IRQ4 triggers on rising edge.
External IRQ4 triggers on low level.
External IRQ4 triggers on high level.
External IRQ3 triggers on falling edge.
External IRQ3 triggers on rising edge.
External IRQ3 triggers on low level.
External IRQ3 triggers on high level.
External IRQ2 triggers on falling edge.
External IRQ2 triggers on rising edge.
External IRQ2 triggers on low level.
External IRQ2 triggers on high level.
External IRQ1 triggers on falling edge.
External IRQ1 triggers on rising edge.
External IRQ1 triggers on low level.
External IRQ1 triggers on high level.
External IRQ0 triggers on falling edge.
External IRQ0 triggers on rising edge.
External IRQ0 triggers on low level.
External IRQ0 triggers on high level.
Rev. PrA | Page 79 of 92
ADuC7122
Preliminary Technical Data
Table 135. Event Selection Numbers
IRQCLRE Register
Name:
IRQCLRE
Address:
0xFFFF0038
Default value:
0x00000000
Access:
Read and write
Table 134. IRQCLRE MMR Bit Designations
Bit
31:20
Name
Reserved
19
IRQ3CLRI
18
IRQ2CLRI
17:15
Reserved
14
IRQ1CLRI
13
IRQ0CLRI
12:0
Reserved
Description
These bits are reserved and should not be
written to.
A 1 must be written to this bit in the IRQ3
interrupt service routine to clear an edge
triggered IRQ3 interrupt.
A 1 must be written to this bit in the IRQ2
interrupt service routine to clear an edge
triggered IRQ2 interrupt.
These bits are reserved and should not be
written to.
A 1 must be written to this bit in the IRQ1
interrupt service routine to clear an edge
triggered IRQ1 interrupt.
A 1 must be written to this bit in the IRQO
interrupt service routine to clear an edge
triggered IRQ0 interrupt.
These bits are reserved and should not be
written to.
TIMERS
Interrupt Number
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
Name
RTOS timer (Timer0)
GP Timer0 (Timer1)
Wake-up timer (Timer2)
Watchdog timer (Timer3)
GP Timer4 (Timer4)
Reserved
Power supply monitor
Undefined
Flash Block 0
Flash Block 1
ADC
UART
SPI
I2C0 master
I2C0 slave
I2C1 master
I2C1 slave
External IRQ0
TIMER0—LIFETIME TIMER
Timer0 is a general-purpose, 48-bit count up, or a 16-bit count
up/down timer with a programmable prescaler. Timer0 is
clocked from the core clock, with a prescaler of 1, 16, 256, or
32768. This gives a minimum resolution of 22 ns when the core
is operating at 41.78 MHz and with a prescaler of 1. Timer 0 can
also be clocked from the undivided core clock, internal 32kHz
oscillator or external 32kHz crystal.
In 48-bit mode, Timer0 counts up from zero. The current
counter value can be read from T0VAL0 and T0VAL1.
The ADuC7122 has five general purpose timers/counters.





ES
00000
00001
00010
00011
00100
00101
00110
00111
01000
01001
01010
01011
01100
01101
01110
01111
10000
10001
Timer0
Timer1
Timer2 or wake-up timer
Timer3 or watchdog timer
Timer4
The five timers in their normal mode of operation can be either
free-running or periodic.
In free-running mode, the counter decrements/increments
from the maximum/minimum value until zero scale/full scale
and starts again at the maximum /minimum value.
In 16-bit mode, Timer0 can count up or count down. A 16-bit
value can be written to T0LD that is loaded into the counter. The
current counter value can be read from T0VAL0. Timer 0 has a
capture register (T0CAP) that can be triggered by a selected IRQ’s
source initial assertion. Once triggered, the current timer value is
copied to T0CAP, and the timer keeps running. This feature can be
used to determine the assertion of an event with more accuracy
than by servicing an interrupt alone.
Timer0 reloads the value from T0LD either when TIMER0
overflows or immediately when T0CLRI is written.
In periodic mode, the counter decrements/increments from the
value in the load register (TxLD MMR) until zero scale/full
scale and starts again at the value stored in the load register.
The value of a counter can be read at any time by accessing its
value register (TxVAL). Timers are started by writing in the
control register of the corresponding timer (TxCON).
In normal mode, an IRQ is generated each time the value of the
counter reaches zero if counting down, or full scale if counting
up. An IRQ can be cleared by writing any value to clear register
of the particular timer (TxICLR).
Rev. PrA | Page 80 of 92
Preliminary Technical Data
ADuC7122
Timer0 interface consists of six MMRs, shown in Table 136.
Table 138. Timer0 Control Register
Table 136. Timer0 Interface MMRs
Name
T0CON
Name
T0LD
T0CAP
T0VAL0/T0VAL1
T0CLRI
T0CON
Description
16-bit register that holds the 16-bit value
loaded into the counter. Available only in
16-bit mode.
16-bit register that holds the 16-bit value
captured by an enabled IRQ event. Available
only in 16-bit mode
TOVAL0 is a 16 bit register that holds the 16
least significant bits (LSBs).
T0VAL1 is a 32-bit register that holds the 32
most significant bits (MSBs).
8-bit register. Writing any value to this register
clears the interrupt. Available only in 16-bit
mode.
Configuration MMR
Address
0xFFFF0304,
0xFFFF0308
Default Value
0x00, 0x00
Bit
31:18
17
Value
16:12
11
10:9
00
01
10
11
8
7
Timer0 Capture Register
Name
T0CAP
Address
0xFFFF0314
Default Value
0x00
Access
R
This is a 16-bit register that holds the 16-bit value captured by
an enabled IRQ event; only available in 16-bit mode.
Access
R/W
Table 139. T0CON MMR Bit Designations
Access
R
T0VAL0 and T0VAL1 are 16-bit and 32-bit registers that hold
the 16 least significant bits and 32 most significant bits,
respectively. T0VAL0 and T0VAL1 are read-only. In 16-bit
mode, 16-bit T0VAL0 is used. In 48-bit mode, both 16-bit
T0VAL0 and 32-bit T0VAL1 are used.
Default Value
0x00
The 17-bit MMR configures the mode of operation of Timer0.
Table 137. Timer0 Value Register
Name
T0VAL0/T0VAL1
Address
0xFFFF030C
6
5
4
0
1
3:0
0000
0100
1000
1111
Description
Reserved.
Event select bit.
Set by user to enable time capture of an
event.
Cleared by user to disable time capture of an
event.
Event select range, 0 to 16. The events are as
described in the introduction to the timers.
Reserved.
Clock select.
Internal 32 kHz oscillator.
UCLK.
External 32kHz crystal.
HCLK.
Count up. Available only in 16-bit mode.
Set by user for timer 0 to count up.
Cleared by user for timer 0 to count down
(default).
Timer0 enable bit.
Set by user to enable Timer0.
Cleared by user to disable Timer0 (default).
Timer0 mode.
Set by user to operate in periodic mode.
Cleared by user to operate in free-running
mode (default).
Reserved.
Timer0 mode of operation.
16-bit operation (default).
48-bit operation.
Prescaler.
Source clock/1 (default).
Source clock/16.
Source clock/256.
Source clock/32,768.
Timer0 Load Registers
Name
T0LD
Address
0xFFFF0300
Default Value
0x00
Access
R/W
T0LD is a 16-bit register that holds the 16-bit value that is
loaded into the counter; available only in 16-bit mode.
Timer0 Clear Register
Name
T0CLRI
Address
0xFFFF0310
Default Value
0x00
Access
W
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload) Timer0.
Rev. PrA | Page 81 of 92
ADuC7122
Preliminary Technical Data
TIMER1—GENERAL-PURPOSE TIMER
Timer1 is a 32-bit general-purpose timer, count down or count
up, with a programmable prescaler. The prescaler source can be
from the 32 kHz internal oscillator, the 32kHz external crystal,
the core clock, or from the undivided PLL clock output. This
source can be scaled by a factor of 1, 16, 256, or 32768. This gives a
minimum resolution of 42 ns when operating at CD zero, the
core is operating at 41.78 MHz, and with a prescaler of 1.
The counter can be formatted as a standard 32-bit value or as
Hours:Minutes:Seconds:Hundredths.
Timer1 has a capture register (T1CAP) that can be triggered by
a selected IRQ’s source initial assertion. Once triggered, the
current timer value is copied to T1CAP, and the timer keeps
running. This feature can be used to determine the assertion of
an event with increased accuracy.
Timer1 interface consists of five MMRs as shown in the table
below.
Table 140. Timer1 Interface Registers
Register
T1LD
T1VAL
T1CAP
T1ICLR
T1CON
Description
32-bit register. Holds 32-bit unsigned integers.
This register is read only.
32-bit register. Holds 32-bit unsigned integers.
32-bit register; Holds 32-bit unsigned integers.
This register is read only.
8-bit register. Writing any value to this register clears
the Timer1 interrupt.
Configuration MMR.
Note that if the part is in a low power mode, and Timer1 is
clocked from the GPIO or low power oscillator source, then
Timer1 continues to operate.
Timer1 reloads the value from T1LD either when Timer1
overflows or immediately when T1ICLR is written.
Table 141. Timer1 Load Registers
Name
Address
Default Value
Access
T1LD
0xFFFF0320
0x00000
R/W
T1LD is a 32-bit register that holds the 32-bit value that is loaded
into the counter.
Table 142. Timer1 Clear Register
Name
T1ICLR
Address
0xFFFF032C
Default Value
0x00
Access
W
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload) Timer1.
Table 143. Timer1 Value Register
Name
T1VAL
Address
0xFFFF0324
Default Value
0x0000
Access
R
T1VAL is a 32-bit register that holds the current value of
Timer1.
Table 144. Timer1 Capture Register
Name
T1CAP
Address
0xFFFF0330
Default Value
0x00
Access
R
This is a 32-bit register that holds the 32-bit value captured by
an enabled IRQ event.
Table 145. Timer1 Control Register.
Name
T1CON
Address
0xFFFF0328
Default Value
0x0000
Access
R/W
This 32-bit MMR configures the mode of operation of Timer1.
Rev. PrA | Page 82 of 92
Preliminary Technical Data
ADuC7122
Table 146. T1CON MMR Bit Designations
Bit
31:24
23
22:20
19
18
17
Value
16:12
11:9
000
001
010
011
8
7
6
5:4
00
01
10
11
3:0
0000
0100
1000
1111
Description
8-bit postscaler.
Enable write to postscaler.
Reserved.
Postscaler compare flag.
T1 interrupt generation selection flag.
Event select bit.
Set by user to enable time capture of an event.
Cleared by user to disable time capture of an event.
Event select range, 0 to 16. The events are as described in the introduction to the timers.
Clock Select.
Internal 32 kHz oscillator (default).
Core clock.
UCLK.
P0.6.
Count up.
Set by user for Timer1 to count up.
Cleared by user for Timer1 to count down (default).
Timer1 enable bit.
Set by user to enable Timer1.
Cleared by user to disable Timer1 (default).
Timer1 mode.
Set by user to operate in periodic mode.
Cleared by user to operate in free-running mode (default).
Format.
Binary (default).
Reserved.
Hr:Min:Sec:Hundredths: 23 hours to 0 hours.
Hr:Min:Sec:Hundredths: 255 hours to 0 hours.
Prescaler.
Source clock/1 (default).
Source clock/16.
Source clock/256.
Source clock/32,768.
Rev. PrA | Page 83 of 92
ADuC7122
Preliminary Technical Data
TIMER2—WAKE-UP TIMER
Table 148. Timer2 Load Registers
Timer2 is a 32-bit wake-up timer, count down or count up, with
a programmable prescaler. The prescaler is clocked directly from 1
of 4 clock sources, namely, the core clock (default selection), the
internal 32.768 kHz oscillator, the external 32.768 kHz watch
crystal, or the PLL undivided clock. The selected clock source
can be scaled by a factor of 1, 16, 256, or 32768. The wake-up
timer continues to run when the core clock is disabled. This
gives a minimum resolution of 22 ns when the core is operating
at 41.78 MHz and with a prescaler of 1. Capture of the current
timer value is enabled if the Timer2 interrupt is enabled via
IRQEN[4].
Name
T2LD
The counter can be formatted as plain 32-bit value or as
Hours:Minutes:Seconds:Hundredths.
Table 150. Timer2 Value Register
The Timer2 interface consists of four MMRs, shown in the table
below.
Table 147. Timer2 Interface Registers
Register
T2LD
T2VAL
T2ICLR
T2CON
Description
32-bit register. Holds 32-bit unsigned integers.
32-bit register. Holds 32-bit unsigned integers. This
register is read only.
8-bit register. Writing any value to this register clears
the Timer2 interrupt.
Configuration MMR.
Default Value
0x00000
Access
R/W
T2LD is a 32-bit register, which holds the 32 bit value that is
loaded into the counter.
Table 149. Timer2 Clear Register
Name
T2CLRI
Address
0xFFFF034C
Default Value
0x00
Access
W
This 8-bit write-only MMR is written (with any value) by user
code to refresh (reload) Timer2.
Name
T2VAL
Timer2 reloads the value from T2LD either when Timer2
overflows or immediately when T2ICLR is written.
Address
0xFFFF0340
Address
0xFFFF0344
Default Value
0x0000
Access
R
T2VAL is a 32-bit register that holds the current value of
Timer2.
Table 151. Timer2 Control Register
Name
T2CON
Address
0xFFFF0348
Default Value
0x0000
Access
R/W
This 32-bit MMR configures the mode of operation for Timer2.
Rev. PrA | Page 84 of 92
Preliminary Technical Data
ADuC7122
Table 152. T2CON MMR Bit Designations
Bit
31:11
10:9
Value
00
01
10
11
8
7
6
5:4
00
01
10
11
3:0
0000
0100
1000
1111
Description
Reserved.
Clock source select.
Internal 32.768 kHz oscillator (default).
Core clock.
External 32.768 kHz watch crystal.
UCLK.
Count up.
Set by user for Timer2 to count up.
Cleared by user for Timer2 to count down (default).
Timer2 enable bit.
Set by user to enable Timer2.
Cleared by user to disable Timer2 (default).
Timer2 mode.
Set by user to operate in periodic mode.
Cleared by user to operate in free-running mode (default).
Format.
Binary (default).
Reserved.
Hr:Min:Sec:Hundredths. 23 hours to 0 hours.
Hr:Min:Sec:Hundredths. 255 hours to 0 hours.
Prescaler.
Source clock/1 (default).
Source clock/16.
Source clock/256. (This setting should be used in conjunction with Timer2 Format 10 and Format 11.)
Source clock/32,768.
Rev. PrA | Page 85 of 92
ADuC7122
Preliminary Technical Data
Timer3 is automatically halted during JTAG debug access and
only recommences counting once JTAG has relinquished control
of the ARM7 core. By default, Timer3 continues to count during
power-down. This can be disabled by setting Bit 0 in T3CON. It is
recommended that the default value is used, that is, the watchdog
timer continues to count during power-down.
TIMER3—WATCHDOG TIMER
16-BIT LOAD
PRESCALER
1, 16, OR 256
16-BIT
UP/DOWN
COUNTER
WATCHDOG
RESET
TIMER3IRQ
TIMER3 VALUE
06020-053
LOW POWER
32.768kHz
Figure 37. Timer3 Block Diagram
Timer3 has two modes of operation: normal mode and
watchdog mode. The watchdog timer is used to recover from an
illegal software state. Once enabled, it requires periodic
servicing to prevent it from forcing a reset of the processor.
Timer3 Interface
Timer3 interface consists of four MMRS as shown in the table
below.
Table 153. Timer3 Interface Registers
Register
T3CON
T3LD
Timer3 reloads the value from T3LD either when Timer3
overflows or immediately when T3ICLR is written.
T3VAL
Normal Mode
T3ICLR
Description
The configuration MMR.
6-bit registers (Bit 0 to Bit15); holds 16-bit unsigned
integers.
6-bit registers (Bit 0 to Bit 15); holds 16-bit unsigned
integers. This register is read only.
8-bit register. Writing any value to this register clears
the Timer3 interrupt in normal mode or resets a new
timeout period in watchdog mode.
The Timer3 in normal mode is identical to Timer0 in 16-bit
mode of operation, except for the clock source. The clock source
is the 32.768 kHz oscillator and can be scaled by a factor of 1,
16, or 256. Timer3 also features a capture facility that allows
capture of the current timer value if the Timer2 interrupt is
enabled via IRQEN[5].
Table 154. Timer3 Load Register
Watchdog Mode
This 16-bit MMR holds the Timer3 reload value.
Watchdog mode is entered by setting T3CON[5]. Timer3 decrements from the timeout value present in the T3LD register until
0. The maximum timeout is 512 seconds, using the maximum
prescalar/256 and full scale in T3LD.
Table 155. Timer3 Value Register
User software should only configure a minimum timeout
period of 30 milliseconds. This is to avoid any conflict with
Flash/EE memory page erase cycles, requiring 20 ms to
complete a single page erase cycle and kernel execution.
Name
T3LD
Name
T3VAL
Address
0xFFFF0360
Address
0xFFFF0364
Default Value
0x03D7
Default Value
0x03D7
Access
R/W
Access
R
This 16-bit, read-only MMR holds the currentTimer3 count value.
Table 156. Timer3 Clear Register
Name
T3CLRI
If T3VAL reaches 0, a reset or an interrupt occurs, depending
on T3CON[1]. To avoid a reset or an interrupt event, any value
must be written to T3ICLR before T3VAL reaches zero. This
reloads the counter with T3LD and begins a new timeout
period.
Once watchdog mode is entered, T3LD and T3CON are write
protected. These two registers cannot be modified until a
power-on reset event resets the watchdog timer. After any other
reset event, the watchdog timer continues to count. The
watchdog timer should be configured in the initial lines of user
code to avoid an infinite loop of watchdog resets.
Address
0xFFFF036C
Default Value
0x00
Access
W
This 8-bit, write-only MMR is written (with any value) by user
code to refresh (reload), Timer3 in watchdog mode to prevent a
watchdog timer reset event.
Table 157. Timer3 Control Register
Name
T3CON
Address
0xFFFF0368
Default Value
0x00
Access
R/W
once
only
The 16-bit MMR configures the mode of operation of Timer3 as
is described in detail in Table 158.
Rev. PrA | Page 86 of 92
Preliminary Technical Data
ADuC7122
Table 158. T3CON MMR Bit Designations
Bit
16:9
8
Value
7
6
5
4
3:2
00
01
10
11
1
0
Description
These bits are reserved and should be written as 0s by user code.
Count up/down enable.
Set by user code to configure Timer3 to count up.
Cleared by user code to configure Timer3 to count down.
Timer3 enable.
Set by user code to enable Timer3.
Cleared by user code to disable Timer3.
Timer3 operating mode.
Set by user code to configure Timer3 to operate in periodic mode.
Cleared by user to configure Timer3 to operate in free-running mode.
Watchdog timer mode enable.
Set by user code to enable watchdog mode.
Cleared by user code to disable watchdog mode.
Secure clear bit.
Set by user to use the secure clear option.
Cleared by user to disable the secure clear option by default.
Timer3 clock(32.768 kHz) prescaler.
Source clock/1 (default).
Reserved.
Reserved.
Reserved.
Watchdog timer IRQ enable.
Set by user code to produce an IRQ instead of a reset when the watchdog reaches 0.
Cleared by user code to disable the IRQ option.
PD_OFF.
Set by user code to stop Timer3 when the peripherals are powered down via Bit 4 in the POWCON MMR.
Cleared by user code to enable Timer3 when the peripherals are powered down via Bit 4 in the POWCON MMR.
Secure Clear Bit (Watchdog Mode Only)
The secure clear bit is provided for a higher level of protection.
When set, a specific sequential value must be written to T3ICLR
to avoid a watchdog reset. The value is a sequence generated by
the 8-bit linear feedback shift register (LFSR) polynomial = X8
+ X6 + X5 + X + 1.
D
7
Q
D
6
Q
D
5
Q
D
4
Q
D
3
Q
D
2
Q
D
1
Q
D
0
06020-054
Q
CLOCK
Figure 38. 8-Bit LFSR
The initial value or seed is written to T3ICLR before entering
watchdog mode. After entering watchdog mode, a write to
T3ICLR must match this expected value. If it matches, the LFSR
is advanced to the next state when the counter reload happens.
If it fails to match the expected state, reset is immediately
generated, even if the count has not yet expired.
The value 0×00 should not be used as an initial seed due to the
properties of the polynomial. The value 0×00 is always
guaranteed to force an immediate reset. The value of the LFSR
cannot be read; it must be tracked/generated in software.
Example of a sequence:
1.
2.
3.
4.
5.
Enter initial seed, 0×AA, in T3ICLR before starting Timer3
in watchdog mode.
Enter 0×AA in T3ICLR; Timer3 is reloaded.
Enter 0×37 in T3ICLR; Timer3 is reloaded.
Enter 0×6E in T3ICLR; Timer3 is reloaded.
Enter 0×66. 0×DC was expected; the watchdog resets
the chip.
Rev. PrA | Page 87 of 92
ADuC7122
Preliminary Technical Data
TIMER4—GENERAL-PURPOSE TIMER
Table 159. Timer4 Load Registers
Timer4 is a 32-bit general-purpose timer, count down or count
up, with a programmable prescalar. The prescalar source can be
the 32kHz oscillator, the core clock or PLL undivided output. This
source can be scaled by a factor of 1, 16, 256, or 32768. This
gives a minimum resolution of 42 ns when operating at
CD zero, the core is operating at 41.78 MHz, and with a prescalar
of 1 ( ignoring external GPIO).
Name
T4LD
The counter can be formatted as a standard 32-bit value or as
Hours:Minutes:Seconds:Hundreths.
Timer4 has a capture register (T4CAP), which can be triggered
by a selected IRQ’s source initial assertion. Once triggered, the
current timer value is copied to T4CAP, and the timer keeps
running. This feature can be used to determine the assertion of
an event with increased accuracy.
Timer4 interface consists of five MMRS.
T4LD, T4VAL and T4CAP are 32-bit registers and hold
32-bit unsigned integers. T4VAL and T4CAP are read only.

T4ICLR is an 8-bit register. Writing any value to this
register clears the Timer1 interrupt.
Timer4 reloads the value from T4LD either when Timer 4
overflows, or immediately when T4ICLR is written.
Default Value
0x00000
Access
R/W
T4LD is a 32-bit register, which holds the 32-bit value that is
loaded into the counter.
Table 160. Timer4 Clear Register
Name
T4CLRI
Address
0xFFFF038C
Default Value
0x00
Access
W
This 8-bit, write only MMR is written (with any value) by user
code to refresh (reload) Timer4.
Table 161. Timer4Value Register
Name
Address
Default Value
Access
T4VAL
0xFFFF0384
0x0000
R
T4VAL is a 32-bit register that holds the current value of Timer4.
Table 162. Timer4 Capture Register

T4CON is the configuration MMR.

Note that if the part is in a low power mode, and Timer 4 is
clocked from the GPIO or oscillator source then, Timer 4
continues to operate.
Address
0xFFFF0380
Name
T4CAP
Address
0xFFFF0390
Default Value
0x00
Access
R
This is a 32-bit register that holds the 32-bit value captured by
an enabled IRQ event.
Table 163. Timer4 Control Register
Name
T4CON
Address
0xFFFF0388
Default Value
0x0000
Access
R/W
This 32-bit MMR configures the mode of operation of Timer4.
Rev. PrA | Page 88 of 92
Preliminary Technical Data
ADuC7122
Table 164. T4CON MMR Bit Designations
Bit
31:18
17
Value
16:12
11:9
000
001
010
011
8
7
6
5:4
00
01
10
11
3:0
0000
0100
1000
1111
Description
Reserved. Set by user to 0.
Event select bit.
Set by user to enable time capture of an event.
Cleared by user to disable time capture of an event.
Event Select Range, 0 to 31. The events are as described in the introduction to the timers.
Clock select:
32.768 kHz oscillator.
Core clock.
UCLK.
UCLK.
Count up.
Set by user for Timer4 to count up.
Cleared by user for Timer4 to count down (default).
Timer4 enable bit.
Set by user to enable Timer4.
Cleared by user to disable Timer4 (default).
Timer4 mode.
Set by user to operate in periodic mode.
Cleared by user to operate in free-running mode (default).
Format.
Binary (default).
Reserved.
Hr:Min:Sec:Hundredths: 23 hours to 0 hours.
Hr:Min:Sec:Hundredths: 255 hours to 0 hours.
Prescaler.
Source clock/1 (default).
Source clock/16.
Source clock/256.
Source clock/32,768.
Rev. PrA | Page 89 of 92
ADuC7122
Preliminary Technical Data
OUTLINE DIMENSIONS
A1 BALL
CORNER
7.10
7.00 SQ
6.90
12 11 10 9 8 7 6 5 4 3 2 1
A
B
C
D
E
F
G
H
J
K
L
M
BALL A1
PAD CORNER
5.50
BSC SQ
0.50
BSC
BOTTOM VIEW
TOP VIEW
DETAIL A
*1.40 MAX
*1.11 MAX
DETAIL A
0.15 MIN
COPLANARITY
0.08
SEATING
PLANE
*COMPLIANT WITH JEDEC STANDARDS MO-195-BD WITH
EXCEPTION TO PACKAGE HEIGHT AND THICKNESS.
Figure 39. 108-Ball Chip Scale Package Ball Grid Array [CSP_BGA]
(BC-108-4
Dimensions shown in millimiters
ORDERING GUIDE
Model
ADuC7122
Temperature Range
−10°C to +95°C
Package Description
108-Ball BGA package
Rev. PrA | Page 90 of 92
090408-A
0.35
0.30
0.25
BALL DIAMETER
Preliminary Technical Data
ADuC7122
NOTES
Rev. PrA | Page 91 of 92
ADuC7122
Preliminary Technical Data
NOTES
I2C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).
©2010 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
PR08755-0-1/10(PrA)
Rev. PrA | Page 92 of 92