Ordering number : EN4339A Thick Film Hybrid IC STK400-040 AF Power Amplifier (Split Power Supply) (25 W + 25 W + 25 W min, THD = 0.4%) Overview Package Dimensions Now, thick-film audio power amplifier ICs are available with pin-compatibility to permit a single PCB to be designed and amplifier output capacity changed simply by installing a hybrid IC. This new series was developed with this kind of pin-compatibility to ensure integration between systems everywhere. With this new series of IC, even changes from 3-channel amplifier to 2-channel amplifiers is possible using the same PCB. In addition, this new series of ICs has a 6/3Ω drive in order to support the low impedance of modern speakers. unit: mm 4086A [STK400-040] Features • Pin-compatible STK400-000 series (3-channel, single package) ➙ STK401-000 series (2-channel, single package) • Output load impedance RL = 6Ω/3Ω supported • New pin arrangement To simplify input/output pattern layout and minimize the effects of pattern layout on operational characteristics, pin assignments are grouped into blocks consisting of input, output and power systems. • Few external circuits Compared to those series used until now, capacitors and boot-strap resistors for external circuits can be greatly reduced. SANYO SANYOElectric ElectricCo.,Ltd. Co.,Ltd.Semiconductor SemiconductorBussiness BussinessHeadquarters Headquarters TOKYO TOKYOOFFICE OFFICETokyo TokyoBldg., Bldg.,1-10, 1-10,11Chome, Chome,Ueno, Ueno,Taito-ku, Taito-ku,TOKYO, TOKYO,110 110JAPAN JAPAN 41097HA(OT) No. 4339-1/9 STK400-040 Specifications Absolute Maximum Ratings at Ta = 25°C Parameter Symbol Maximum supply voltage Conditions Ratings VCC max θj – c Thermal resistance Per power transistor Unit ±36 V 2.1 °C/W Junction temperature Tj 150 °C Operating substrate temperature Tc 125 °C –30 to +125 °C Storage temperature range Tstg Available time for short-circuit ts VCC = ±25 V, RL = 6 Ω, f = 50 Hz, PO = 25 W 1 s max Unit 150 mA Operating Characteristics at Ta = 25°C, RL = 6Ω, Rg = 600Ω, VG = 40dB, RL (non-inductive) Parameter Quiescent current Output power Total harmonic distortion Frequency response Symbol ICCO Conditions min typ VCC = ± 30 V 30 90 PO (1) VCC = ±25 V, f = 20 Hz to 20 kHz, THD = 0.4% 25 30 PO (2) VCC = ±21 V, f = 1 kHz, THD = 1.0%, RL = 3 Ω 25 30 THD (1) VCC = ±25 V, f = 20 Hz to 20 kHz, PO = 1.0 W THD (2) VCC = ±25 V, f = 1 kHz, PO = 5.0 W fL, fH Input impedance Output noise voltage Neutral voltage ri VNO VN W 0.4 +0 VCC = ±25 V, PO = 1.0 W, –3 dB VCC = ±25 V, f = 1 kHz, PO = 1.0 W % 20 to 50 k Hz 55 –70 % 0.02 VCC = ±30 V, Rg = 10 kΩ VCC = ±30 V W 0 kΩ 1.2 mVrms +70 mV Notes • Use rated power supply for test unless otherwise specified. • When measuring available time for short-circuit and output noise voltage use transformer power supply indicated below. • Output noise voltage is represented by the peak value rms (VTVM) for mean reading. Use an AC stabilized power supply (50 Hz) on the primary side to eliminate the effect of AC flicker noise. Specified Transformer Power Supply (RP-25 Equivalent) Unit (resistance:Ω, capacitance:F) Internal Equivalent Circuit No. 4339-2/9 STK400-040 Pattern Example for PCB used with either 2- or 3-channel Amplifiers. Sample Application Circuit STK 400-000 Series Copper (Cu) foil surface Unit (resistance:Ω, capacitance:F) In the STK 401-000 series, pin No.6 corresponds to pin No.1. Sample Application Circuit Unit (resistance: Ω, capacitance: F) No. 4339-3/9 STK400-040 Description of External Circuits C1, 11, 21 For input coupling capacitor. Used for current blocking. When capacitor reactance with low frequency is increased, the reactance value should be reduced in order to reduce the output noise from the signal resistance dependent 1/f noise. In response to the popping noise which occurs when the system power is turned on, C1 and C11 which determine the decay time constant on the input side are increased while C3, C13 and C23 on the NF side are decreased. C2, 12, 22 For input filter capacitor. Permits high-region noise reduction by utilizing filter constructed with R1, R11 and R21. C3, 13, 23 For NF capacitor. This capacitor determines the decline of the cut-off frequency and is calculated according to the following equation. fL = 1 2π X C3 (13, 23,) X R3 (13, 23) For the purpose of achieving voltage gains prior to reduction, it is best that C3, C13 and C23 are large. However, because the shock noise which occurs when the system power is turned on tends to increase, values larger than those absolutely necessary should be avoided. C5, 15, 25 For oscillation prevention capacitor. A Mylar capacitor with temperature and frequency features is recommended. C6, 7 For oscillation prevention capacitor. To ensure safe IC functioning, the capacitor should be installed as close as possible to the IC power pin to reduce power impedance. An electrolytic capacitor is good. C8, 9, 28, 29 For decoupling capacitor. Reduces shock noise during power up using decay time constant circuits with R8, R9, R28 and R29 and eliminates components such as ripples crossing over into the input side from the power line. R1, 11, 21 For input filter applied resistor. R2, 12, 22 For input bias resistor. The input pin is biased to zero potential. Input impedance is mostly decided with this resistance value. R3, 13, 23 R4, 14, 24 For resistors to determine voltage gain (VG). We recommend a VG = 40 dB using R3, R13, R23 = 560Ω and R4, R14 and R24 = 56Ω. VG adjustments are best performed using R3, R13 and R23. When using R4, R14 and R24 for such purposes, R4, R14 and R24 should be set to equal R2, R12 and R22 in order to establish a stable VN balance. R5, 15, 25 For oscillation prevention resistor. R6, 16, 26 For oscillation prevention resistor. This resistor’s electrical output resides in the signal frequency and is calculated according to the following formula. VCC max/√2 2 P R6 (16, 26) = ( 1/2π fC5 (15, 25) + R6 (16, 26) ) X R6 (16, 26) f = output signal frequency upper limit R8, 9, 28, 29 For ripple filter applied resistor. PO max, ripple rejection and power-up shock noise are modified according to this value. Set the electrical output of these resistors while keeping in mind the flow of peak current during recharging to C8, C9, C28 and C29 which function as pre-drive TR control resistors during load shorts. L1, 2, 3 For oscillation prevention coil. Compensates phase dislocation caused by load capacitors and ensures stable oscillation. No. 4339-4/9 STK400-040 Series Configuration Supply voltage Fixed Standard Output 2ch Amp IC Name Fixed Standard Output STK400-010 10W X 3 STK401-010 10W X 2 — STK400-020 15W X 3 STK401-020 15W X 2 STK400-030 20W X 3 STK401-030 STK400-040 25W X 3 STK401-040 STK400-050 30W X 3 STK400-060 3ch Amp IC Name THD [%] f = 20 to 20kHz VCC1 VCC2 ±27 ±18 ±14 — ±29 ±20 ±16 20W X 2 — ±34 ±23 ±19 25W X 2 — ±36 ±25 ±21 STK401-050 30W X 2 — ±39 ±26 ±22 35W X 3 STK401-060 35W X 2 — ±41 ±28 ±23 STK400-070 40W X 3 STK401-070 40W X 2 — ±44 ±30 ±24 STK400-080 45W X 3 STK401-080 45W X 2 — ±45 ±31 ±25 STK400-090 50W X 3 STK401-090 50W X 2 — ±47 ±32 ±26 STK400-100 60W X 3 STK401-100 60W X 2 — ±51 ±35 ±27 STK400-110 70W X 3 STK401-110 70W X 2 ±56.0 — ±38 — — — STK401-120 80W X 2 ±61.0 — ±42 — — — STK401-130 100W X 2 ±65.0 — ±45 — — — STK401-140 120W X 2 ±74.0 — ±51 — 0.4 VCC max1 VCC max2 VCC max1 VCC max2 VCC1 VCC2 RL = 6Ω operation RL = 6Ω to 3Ω operation RL = 6Ω operation RL = 3Ω operation Example of Set Design for Common PCB 6-channel amplifier STK400-000 Series STK400-000 Series 5-channel amplifier STK400-000 Series STK401-000 Series 4-channel amplifier STK401-000 Series 3-channel amplifier STK400-000 Series 2-channel amplifier STK401-000 Series No. 4339-5/9 STK400-040 External Circuit Diagram *1 Unnecessary with applications using STK400-010 to STK400-090. Unit (resistance:Ω, capacitance:F) *2 Unnecessary with applications using STK401-010 to STK401-090. Heat Radiation Design Considerations The radiator thermal resistance θc-a required for total substrate power dissipation Pd in the STK400-040 is determined as: Condition 1: IC substrate temperature Tc not to exceed 125°C. Pd x θc-a+Ta <125°C ······························· (1) where Ta is set assured ambient temperature. Condition 2: Power transistor junction temperature Tj not to exceed 150°C. Pd x θc-a+Pd/N x θj-c+Ta<150°C·············(2) where N is the number of power transistors and θj-c the thermal resistance per power transistor chip. However, power transistor power consumption is Pd equally divided by N units. Expressions (1) and (2) can be rewritten based on θc-a to yield: θc-a<(125–Ta)/Pd ······································(1)' θc-a<(150–Ta)/Pd–θj-c/N··························(2)' The required radiator thermal resistance will satisfy both of these expressions. From expressions (1)' and (2)', the required radiator thermal resistance can be determined once the following specifications are known: • • • Supply voltage VCC Load resistance RL Assured ambient temperature Ta The total substrate power consumption when STK400-040 VCC is ±25 V and RL is 6 Ω, for a continuous sine wave signal, is a maximum of 63W (Fig. 1). In general, when this sort of continuous signal is used for estimation of power consumption, the Pd used is 1/10th of PO max (slight variation depending on safety standard). No. 4339-6/9 STK400-040 3-channels driven simultaneously Figure 2 3-channels driven simultaneously Output power per single channel, PO/ch – W Total harmonic distortion, THD – % Output power per single channel, PO/ch – W Total substrate power dissipation (3-channel drive), Pd – W Figure 1 Total harmonic distortion, THD – % Total substrate power dissipation (3-channel drive), Pd – W Pd = 38W (1/10 PO max = during 2.5W) Output power, PO – W Output power, PO – W No. 4339-7/9 Neutral voltage, VN – mV Quiescent current, ICCO – mA Open loop gain, VG – dB Output power, PO – W Input voltage, Vin – mVrms Supply voltage, VCC – V Frequency, f – Hz Neutral voltage, VN – mV Quiescent current, ICCO – mA Closed loop gain, VG – dB Output power, PO – W Output power, PO – W STK400-040 Frequency, f – Hz Frequency, f – Hz Substrate temperature, Tc – °C Supply voltage, VCC – V No. 4339-8/9 STK400-040 ■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. ■ Anyone purchasing any products described or contained herein for an above-mentioned use shall: ➀ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: ➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. ■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of April, 1997. Specifications and information herein are subject to change without notice. No. 4339-9/9