Ordering number : EN4585A Thick Film Hybrid IC STK4211V 2-Channel 70 W min AF Power Amplifier (Split Power Supply) Features Package Dimensions • The inclusion of a muting circuit on-chip allows all types of impulse noise to be excluded. • Current mirror circuit application reduces distortion to 0.008%. • Pin compatible with the STK4201II Series (THD = 0.4%) and the STK4141X Series (THD = 0.02%) unit: mm 4086A [STK4211V] Specifications Maximum Ratings at Ta = 25°C Parameter Maximum supply voltage Symbol VCC max Condition Rating ±62 Unit V θj-c 1.5 °C/W Junction temperature Tj 150 °C Operating case temperature Tc 125 °C Thermal resistance Storage temperature Tstg Available time for load shorted tS* –30 to +125 °C 1 sec VCC = ±43 V, RL = 8 Ω, f = 50 Hz, PO = 70 W Note: Use a constant voltage power supply as the test power supply unless otherwise specified. * Use the transformer power supply shown on the next page when measuring the available time for load shorted and the output noise voltage. Recommended Operating Conditions at Ta = 25°C Parameter Recommended supply voltage Load resistance Symbol VCC RL Condition Rating ±43 8 Unit V Ω SANYO Electric Co.,Ltd. Semiconductor Bussiness Headquarters TOKYO OFFICE Tokyo Bldg., 1-10, 1 Chome, Ueno, Taito-ku, TOKYO, 110 JAPAN 61096HA (OT)/52493YO 5-2377 No. 4585-1/3 STK4211V Operating Characteristics at Ta = 25°C, VCC = ±43 V, RL = 8 Ω (noninductive load), RG = 600 Ω, VG = 40 dB Parameter Quiescent current Output power Symbol ICCO PO Total harmonic distortion THD Frequency response Input resistance Output noise voltage Condition min VCC = ±50.5 V 20 THD = 0.08%, f = 20 Hz to 20 kHz 70 Rating typ 40 Unit max 100 mA W fL, fH PO = 1.0 W, f = 1 kHz +0 PO = 1.0 W, –3 dB 20 to 50 k Hz ri PO = 1.0 W, f = 1 kHz 55 kΩ VNO* Neutral voltage VN Muting voltage VM 0.08 VCC = ±50.5 V, Rg = 10 kΩ VCC = ±50.5 V % 1.2 mVrms –70 0 +70 mV –2 –5 –10 V Note: Use a constant voltage power supply as the test power supply unless otherwise specified. * The output noise voltage is the peak value measured with an averaging rms scale volt meter. The noise voltage waveform should not include pulse noise. Specified Transformer Power Supply (MG-200 equivalent) Equivalent Circuit No. 4585-2/3 STK4211V Sample Application Circuit: 2-Channel 70 W min AF Power Amplifier Unit (resistance: Ω, capacitance: F) ■ No products described or contained herein are intended for use in surgical implants, life-support systems, aerospace equipment, nuclear power control systems, vehicles, disaster/crime-prevention equipment and the like, the failure of which may directly or indirectly cause injury, death or property loss. ■ Anyone purchasing any products described or contained herein for an above-mentioned use shall: ➀ Accept full responsibility and indemnify and defend SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors and all their officers and employees, jointly and severally, against any and all claims and litigation and all damages, cost and expenses associated with such use: ➁ Not impose any responsibility for any fault or negligence which may be cited in any such claim or litigation on SANYO ELECTRIC CO., LTD., its affiliates, subsidiaries and distributors or any of their officers and employees jointly or severally. ■ Information (including circuit diagrams and circuit parameters) herein is for example only; it is not guaranteed for volume production. SANYO believes information herein is accurate and reliable, but no guarantees are made or implied regarding its use or any infringements of intellectual property rights or other rights of third parties. This catalog provides information as of November, 1997. Specifications and information herein are subject to change without notice. No. 4585-3/3