19-1952; Rev 3; 12/05 Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer Features The MAX6701–MAX6708 microprocessor (µP) supervisory circuits reduce the complexity and components required to monitor power-supply functions in µP systems. These devices significantly improve system reliability and accuracy compared to separate ICs or discrete components. The MAX6701–MAX6708 family provides four functions: a reset output during power-up, power-down, and brownout conditions; an independent watchdog output that goes low if the watchdog input has not been toggled within 1.6s; a 0.62V threshold detector for power-fail warning; and an active-low manual reset input. The MAX6701–MAX6708 family offers several pinout options to accommodate a variety of multivoltage microprocessor supervision applications. The MAX6701(A)/MAX6702(A)/MAX6703(A) monitor three supply voltages (one fixed threshold and two adjustable) to drive a single reset output and include a manual reset input and a watchdog timer with an independent output. The MAX6704 monitors a single-supply voltage to drive complementary reset outputs and includes an independent adjustable power-fail-in/powerfail-out comparator, a manual reset input, and a resetbased watchdog timer. The MAX6705(A)/MAX6706(A)/ MAX6707(A) monitor a single-supply voltage to drive a single reset output and include an independent adjustable power-fail-in/power-fail-out comparator, a manual reset input, and a watchdog timer with an independent output. The MAX6708 is the same as the MAX6704 but without the watchdog timer function. See the Detailed Description for differences between non-A and A versions. ♦ Small 8-Pin SOT23 Package ♦ Precision Monitoring of +5.0V, +3.3V, +3.0V, +2.5V Supply Voltages ♦ 140ms Reset Timeout Delay ♦ Power-Fail Input with Independent Output; Monitor Inputs Down to 0.62V (MAX6704–MAX6708) ♦ Dual Adjustable Reset Input for Triple-Voltage Monitoring (MAX6701(A)/MAX6702(A)/MAX6703(A)) ♦ 1.6s Watchdog Timeout Period (MAX6701(A)–MAX6707(A)) ♦ Independent Watchdog Output (MAX6701(A)/MAX6702(A)/MAX6703(A)/ MAX6705(A)/MAX6706(A)/MAX6707(A)) ♦ Manual Reset Input ♦ Four Reset Output Stage Options Active Low Push-Pull (MAX6701(A), MAX6705(A)) Active Low Open Drain (MAX6703(A), MAX6707(A)) Active High Push-Pull (MAX6702(A), MAX6706(A)) Dual Active Low/High Push-Pull (MAX6704, MAX6708) ♦ Guaranteed Reset Valid to VCC = 1V ♦ Immune to Short Falling VCC Transients ♦ Low Cost, Few External Components Ordering Information PART TEMP RANGE PIN-PACKAGE MAX6701_KA-T -40°C to +125°C 8 SOT23-8 MAX6701A_KA-T -40°C to +125°C 8 SOT23-8 Computers Insert the desired suffix letter (from the Threshold Suffix Guide table) into the blank to complete the part number. All devices must be ordered in increments of 2500 pieces. Sample stock is typically held on standard versions only. Contact factory for availability. Devices are available in both leaded and lead-free packaging. Specify lead-free by replacing “-T” with “+T” when ordering. Controllers Ordering Information continued at end of data sheet. Applications Intelligent Instruments Pin Configurations Automotive Systems Critical µP Power Monitoring TOP VIEW MR 1 White Goods Networking VCC 2 Telecommunications GND 3 MAX6701(A) MAX6702(A) MAX6703(A) RST_IN1 4 Typical Operating Circuit and Selector Guide appear at end of data sheet. ( ) ARE FOR MAX6702(A) ONLY. 8 WDO 7 RESET (RESET) 6 WDI 5 RST_IN2 SOT23 Pin Configurations continued at end of data sheet. ________________________________________________________________ Maxim Integrated Products For pricing, delivery, and ordering information, please contact Maxim/Dallas Direct! at 1-888-629-4642, or visit Maxim’s website at www.maxim-ic.com. 1 MAX6701–08/MAX6701A–03A/05A–07A General Description MAX6701–08/MAX6701A–03A/05A–07A Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer ABSOLUTE MAXIMUM RATINGS VCC ........................................................................-0.3V to +6.0V Open-Drain RESET, WDO, PFO ...........................-0.3V to +6.0V Push-Pull RESET, RESET, WDO, PFO ........-0.3V to (VCC + 0.3V) MR, WDI, PFI, RST_IN1, RST_IN2 ..............-0.3V to (VCC + 0.3V) Input Current (VCC) .............................................................20mA Output Current (RESET, RESET, PFO, WDO) .....................20mA Continuous Power Dissipation (TA = +70°C) 8-Pin SOT23 (derate 8.9mW/°C above +70°C)............714mW Operating Temperature Range .........................-40°C to +125°C Junction Temperature ......................................................+150°C Storage Temperature Range .............................-65°C to +150°C Lead Temperature (soldering, 10s) .................................+300°C Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ELECTRICAL CHARACTERISTICS (VCC = +4.25V to +5.5V for L/M versions, VCC = +2.55V to +3.6V for the T/S/R versions, VCC = +2.1V to +2.75V for the Z/Y versions. TA = -40°C to +125°C, unless otherwise specified. Typical values are at TA = +25°C.) (Note 1) PARAMETER SYMBOL Operating Voltage Range VCC Supply Current MR Unconnected CONDITIONS 1.0 5.5 1.2 5.5 9 20 6 20 4.63 4.75 4.38 4.50 3.08 3.15 2.93 3.00 MAX670_S/MAX670_AS MAX670_R/MAX670_AR MAX670_Z/MAX670_AZ MAX670_Y/MAX670_AY 4.50 TA = -40°C to +125°C 4.47 TA = -40°C to +85°C 4.25 TA = -40°C to +125°C 4.22 TA = -40°C to +85°C 3.00 TA = -40°C to +125°C 2.97 TA = -40°C to +85°C 2.85 TA = -40°C to +125°C 2.83 TA = -40°C to +85°C 2.55 TA = -40°C to +125°C 2.53 TA = -40°C to +85°C 2.25 TA = -40°C to +125°C 2.24 TA = -40°C to +85°C 2.12 TA = -40°C to +125°C 2.11 ∆VTH VCC to Reset Output Delay Reset Timeout Period TA = -40°C to +85°C VCC falling at 10mV/µs tRP TA = -40°C to +85°C 140 TA = -40°C to +125°C 120 VCC Falling to WDO Delay MAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/ MAX6706(A)/MAX6707(A) PFI, RST_IN1, RST_IN2 Threshold VCC = 1.8V to 5.5V PFI Hysteresis 2 602 TA = -40°C to +125°C 593 V µA 4.78 4.53 3.17 3.02 2.63 2.70 2.32 2.38 V 2.72 2.40 2.19 2.25 2.27 60 ppm/°C 12 µs 200 280 300 5 TA = -40°C to +85°C UNITS 25 VCC < 3.6V, no load (MAX6708 only) MAX670_T/MAX670_AT Reset Threshold Temperature Coefficient 12 VCC < 3.6V, no load MAX670_M/MAX670_AM VTH MAX TA = -40°C to +125°C VCC < 5.5V, no load ICC TYP TA = 0°C to +125°C MAX670_L/MAX670_AL VCC Reset Threshold (VCC falling) MIN 618 µs 634 642 6 _______________________________________________________________________________________ ms mV mV Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer (VCC = +4.25V to +5.5V for L/M versions, VCC = +2.55V to +3.6V for the T/S/R versions, VCC = +2.1V to +2.75V for the Z/Y versions. TA = -40°C to +125°C, unless otherwise specified. Typical values are at TA = +25°C.) (Note 1) PARAMETER SYMBOL PFI, RST_IN1, RST_IN2 Leakage Current PFI to PFO Delay CONDITIONS (Note 2) TA = -40°C to +85°C MIN -50 TA = -40°C to +125°C -200 tPF 0.3 x VCC 1 MR Glitch Rejection tMD MAX6701(A)/MAX6702(A)/MAX6703(A)/ MAX6705(A)/MAX6706(A)/MAX6707(A) VCC Rising to WDO Delay MR Pullup Resistance Watchdog Timeout Period tWD WDI Pulse Width tWDI WDI Input Voltage WDI Input Current IWDI RESET, WDO Output Low (Push-Pull or Open Drain) PFO Output Low (Push-Pull or Open Drain) VOL VOH RESET, WDO, PFO Output Open-Drain Leakage Current ILKG VOH VOL 100 ns 50 75 2.4 TA = -40°C to +125°C 0.96 2.52 50 0.7 x VCC WDI = 0V or VCC -1 kΩ s ns 0.3 x VCC +1 V µA 0.3 VCC ≥ 1.2V, ISINK = 100µA, output asserted 0.3 VCC ≥ 2.55V, ISINK = 1.2mA, output asserted 0.3 VCC ≥ 4.25V, ISINK = 3.2mA, output asserted 0.4 VCC ≥ 1.80V, ISINK = 200µA, output asserted 0.3 VCC ≥ 2.55V, ISINK = 1.2mA, output asserted 0.3 VCC ≥ 4.25V, ISINK = 3.2mA, output asserted RESET, WDO, PFO Output High (Push-Pull Only) ns 1.6 VCC ≥ 1.0V, ISINK = 50µA, output asserted (TA = 0°C to +125°C) VOL ns 200 25 VIH V 100 1.12 (Note 2) nA µs TA = -40°C to +85°C VIL UNITS µs 0.7 x VCC MR Minimum Input Pulse RESET Output Low (Push-Pull Only) +200 1 VIH MR to Reset Delay MAX +50 VIL MR Input Voltage RESET Output High (Push-Pull Only) TYP V V 0.4 VCC ≥ 2.7V, ISOURCE = 500µA, output not asserted 0.8 x VCC VCC ≥ 4.75V, ISOURCE = 800µA, output not asserted 0.8 x VCC VCC > VTH, output not asserted V 1.0 VCC ≥ 1.0V, ISOURCE = 1µA, reset asserted (TA = 0°C to +125°C) 0.8 x VCC VCC ≥ 1.2V, ISOURCE = 50µA, reset asserted 0.8 x VCC VCC ≥ 2.55V, ISOURCE = 500µA, reset asserted 0.8 x VCC VCC ≥ 4.25V, ISOURCE = 800µA, reset asserted 0.8 x VCC µA V VCC ≥ 2.7V, ISINK = 1.2mA, reset not asserted 0.3 VCC ≥ 4.75V, ISINK = 3.2mA, reset not asserted 0.4 V Note 1: Over-temperature limits are guaranteed by design and not production tested. Devices are tested at TA = +25°C. Note 2: Guaranteed by design. Not production tested. _______________________________________________________________________________________ 3 MAX6701–08/MAX6701A–03A/05A–07A ELECTRICAL CHARACTERISTICS (continued) Typical Operating Characteristics (TA = +25°C, unless otherwise noted.) 8 MAX6708 VCC = 3.3V 4 0 195 -15 10 35 60 -40 85 10 5 0 190 -15 10 35 60 -40 85 -15 10 35 60 85 TEMPERATURE (°C) TEMPERATURE (°C) TEMPERATURE (°C) WATCHDOG TIMEOUT PERIOD vs. TEMPERATURE NORMALIZED RESET THRESHOLD vs. TEMPERATURE MAXIMUM VCC TRANSIENT DURATION vs. RESET THRESHOLD OVERDRIVE 1.65 1.60 1.55 1.05 1.04 1.03 1.02 1.01 1.00 0.99 0.98 0.97 60 MAXIMUM TRANSIENT DURATION (µs) MAX6701 toc04 1.70 NORMALIZED RESET THRESOLD -40 MAX6701 toc03 MAX6701 toc02 200 15 MAX670_Y 50 MAX6701 toc06 12 205 20 VCC TO RESET OUTPUT DELAY (µs) MAX6705(A) VCC = 5V MAX6701 toc05 SUPPLY CURRENT (µA) 16 210 RESET TIMEOUT PERIOD (ms) MAX6701 toc01 20 VCC TO RESET OUTPUT DELAY vs. TEMPERATURE RESET TIMEOUT PERIOD vs. TEMPERATURE SUPPLY CURRENT vs. TEMPERATURE WATCHDOG TIMEOUT PERIOD (s) 40 RESET OCCURS ABOVE LINE 30 20 10 0.96 0 0.95 -40 -15 10 35 60 85 -40 TEMPERATURE (°C) -15 10 35 60 85 0 OUTPUT-VOLTAGE LOW vs. SINK CURRENT VCC ≥ 4.25V 80 VCC - VOH vs. SOURCE CURRENT 350 MAX6701 toc07 100 40 VCC ≥ 4.25V 300 75 VCC - VOH (mV) 250 50 200 150 100 25 50 0 0 0 400 800 1200 1600 2000 2400 2800 3200 SINK CURRENT (µA) 4 0 120 RESET THRESHOLD OVERDRIVE (mV) TEMPERATURE (°C) MAX6701 toc08 1.50 VOL (mV) MAX6701–08/MAX6701A–03A/05A–07A Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer 400 800 1200 1600 2000 2400 2800 3200 SOURCE CURRENT (µA) _______________________________________________________________________________________ 160 Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer PIN MAX6701(A) MAX6702(A) MAX6704 MAX6703(A) MAX6705(A) MAX6706(A) MAX6708 MAX6707(A) NAME FUNCTION 1 1 1 1 MR Active-Low, Manual Reset Input, Internal 50kΩ Pullup to VCC. Pull low to force a reset. Reset remains active as long as MR is low and the reset timeout period after MR goes high. Leave unconnected or connect to VCC if unused. WDO deasserts when MR is low (MAX6701(A)/MAX6702(A)/MAX6703(A)/ MAX6705(A)/ MAX6706(A)/MAX6707(A) only). 2 2 2 2 VCC Supply Voltage for MAX6701–MAX6708 and Input for Primary Reset Threshold Monitor. Push-pull outputs are powered by VCC. 3 3 3 3 GND Ground — 4 4 4 PFI Power-Fail Voltage Monitor Input. High-impedance input for internal power-fail comparator. Connect this pin to an external resistive-divider network to set the reset threshold voltage; 0.62V (typ) threshold. Connect to GND or VCC when not used. — 5 5 5 PFO Power-Fail Monitor Output. Open drain or push-pull active low. PFO goes low when PFI is less than 0.62V. 6 6 6 — WDI Watchdog Input. If WDI remains high or low for longer than the watchdog timeout period, the internal watchdog timer runs out and WDO is asserted. WDO is asserted low after each watchdog overflow and remains low until the watchdog timer is cleared (the reset output is not affected). The internal watchdog timer clears whenever a VCC/RST_IN1/RST_IN2 reset is asserted, the manual reset is asserted, or WDI sees a rising or falling edge. The watchdog timer remains cleared until the reset output is deasserted. On the MAX6704, RESET pulse asserts for the reset timeout period after each watchdog timeout overflow. The watchdog timer cannot be disabled. — — — 6 N.C. No Connection. Not internally connected. 7 7 7 7 RESET Active-Low Reset Output (Open Drain or Push-Pull). RESET changes from high to low when the VCC input drops below the selected reset threshold (or RST_IN1/ RST_IN2 for the MAX6701(A)/MAX6702(A)/MAX6703(A), MR is pulled low, or the watchdog triggers a reset (MAX6704 only). RESET remains low for the reset timeout period after the reset conditions are terminated. _______________________________________________________________________________________ 5 MAX6701–08/MAX6701A–03A/05A–07A Pin Description Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer MAX6701–08/MAX6701A–03A/05A–07A Pin Description (continued) PIN MAX6701(A) MAX6702(A) MAX6704 MAX6703(A) 8 7* 4 5 — 8 — — MAX6705(A) MAX6706(A) MAX6708 MAX6707(A) 8 7* — — — 8 — — NAME FUNCTION WDO Active-Low Watchdog Output (Open Drain or Push-Pull). WDO is asserted whenever the watchdog times out and VCC or the reset inputs are below their respective thresholds. WDO deasserts after a valid WDI transition without a reset timeout period. In the A versions, WDO deasserts without a timeout delay when VCC, RST_IN1, and RST_IN2 rises above its threshold. Pull MR low to assert WDO (MAX6701/MAX6702/ MAX6703/MAX6705/MAX6706/MAX6707 only). Pull MR low to deassert WDO (MAX6701(A)/MAX6702(A)/MAX6703(A)/ MAX6705(A)/MAX6706(A)MAX6707(A) only). RESET Active-High Reset Output (Push-Pull). RESET changes from low to high when the VCC input drops below the selected reset threshold (or RST_IN1/RST_IN2 for MAX6701(A)/MAX6702(A)/ MAX6703(A), MR is pulled low, or the watchdog triggers a reset (MAX6704 only). RESET remains high for the reset timeout period after the reset conditions are terminated. RST_IN1 Input for User-Adjustable VCC2 Monitor. High-impedance input for second internal reset comparator. Connect this pin to an external resistive-divider network to set the reset threshold voltage; 0.62V (typ) threshold. Connect to VCC when not used. Reset is asserted when either VCC, RST_IN1, or RST_IN2 are below threshold. RST_IN2 Input for User-Adjustable VCC3 Monitor. High-impedance input for third internal reset comparator. Connect this pin to an external resistive-divider network to set the reset threshold voltage; 0.62V (typ) threshold. Connect to VCC when not used. Reset is asserted when either VCC, RST_IN1, or RST_IN2 are below threshold. *RESET active-high for the MAX6702(A)/MAX6706(A). Detailed Description Figures 1, 2, and 3 are functional diagrams for the MAX6705(A)/MAX6706(A)/MAX6707(A), MAX6704/ MAX6708, and MAX6701(A)/ MAX6702(A)/MAX6703(A), respectively. Reset Output A microprocessor’s (µP’s) reset input starts the µP in a known state. The MAX6701–MAX6708 assert reset during power-up and prevent code execution errors during power-down or brownout conditions. On power-up, once VCC reaches 1V, RESET is a guaranteed logic low of 0.4V or less. As VCC rises, RESET 6 stays low. After VCC, RST_IN1, or RST_IN2 rise above the reset threshold, an internal timer holds RESET low for about 200ms. RESET pulses low whenever VCC dips below the reset threshold, including brownout conditions. If a brownout occurs in the middle of a previously initiated reset pulse, the pulse continues for at least another 140ms. On power-down, once VCC falls below the reset threshold, RESET stays low and is guaranteed to be 0.4V or less, until VCC drops below 1V. The MAX6702(A)/MAX6704/MAX6706(A)/MAX6708 active-high RESET output is the complement of the RESET output, and is guaranteed to be valid with VCC down to 1V. _______________________________________________________________________________________ Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer 8 WATCHDOG TIMER VCC VCC WDO 50kΩ 50kΩ VCC 7 RESET GENERATOR 4 RESET GENERATOR RESET (RESET) 5 WDO RST_IN1 GND 0.62V ( ) ARE FOR MAX6702(A) ONLY. Figure 1. MAX6705(A)/MAX6706(A)/MAX6707(A) Functional Diagram Figure 3. MAX6701(A)/MAX6702(A)/MAX6703(A) Functional Diagram VTH VCC VTH VCC 50kΩ VCC RST_IN2 0.62V 3 WDI PFO 0.62V ( ) ARE FOR MAX6706(A) ONLY. RESET (RESET) WATCHDOG TIMER VREF MAX6705(A) MAX6706(A) MAX6707(A) VREF MR MAX6701(A) MAX6702(A) MAX6703(A) MR MR 1 VCC 2 PFI MAX6701–08/MAX6701A–03A/05A–07A 6 WDI MAX6704 MAX6708 tRP 8 1 2 RESET GENERATOR 7 WATCHDOG TIMER 6 RESET RESET WDI (MAX6704 ONLY) tRP VCC RESET 0V VCC MR 0V tMD VREF PFI VCC WDO 4 5 0V PFO MR EXTERNALLY DRIVEN LOW VCC 0.62V WDI 0V 3 GND Figure 2. MAX6704/MAX6708 Functional Diagram NOTE: THE MAX6706 RESET OUTPUT IS THE INVERSE OF THE RESET SHOWN. Figure 4. MAX6705/MAX6706/MAX6707 RESET, MR, WDO, and WDI Timing _______________________________________________________________________________________ 7 MAX6701–08/MAX6701A–03A/05A–07A Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer Standard- vs. A-Version Comparison The MAX6701/MAX6702/MAX6703/MAX6705/MAX6706/ MAX6707s’ WDO latches low when one of the following events occurs: • The watchdog timer times out (1.6s, typ). • VCC, RST_IN1, or RST_IN2 is below its reset threshold. • MR is pulled low. • WDO only deasserts with a valid WDI transition. TheMAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/ MAX6706(A)/MAX6707(A)s’ WDO asserts when either VCC, RST_IN1, or RST_IN2 is below its reset threshold. WDO deasserts without a timeout delay when the undervoltage situation has expired. WDO is latched low when the watchdog timer elapses without seeing a WDI transition. WDO deasserts with a valid WDI transition OR by pulling MR low. See Figures 4 and 5 for standard-version timing. See Figures 6 and 7 for A-version timing. Watchdog Timer The MAX6701–MAX6707 watchdog circuit monitors the µP’s activity. If the µP does not toggle the WDI within 1.6s, WDO goes low. When RESET is asserted, the watchdog timer stays cleared and does not count. As soon as reset is released, the timer starts counting. WDO deasserts after a valid transition is detected at WDI. Pulses as short as 50ns can be detected. Typically, WDO is connected to the NMI input of a µP. When VCC, RST_IN1, or RST_IN2 drop below the reset tWDI WDI tWD threshold, WDO goes low whether or not the watchdog timer has timed out. Normally this would trigger an NMI, but RESET goes low simultaneously, and thus overrides the NMI. The MAX6704 watchdog circuit does not have an independent watchdog output (WDO). If the µP does not toggle the watchdog input within 1.6s, the MAX6704 asserts a reset output pulse for the reset timeout period. Manual Reset The manual reset input (MR) allows reset to be triggered by a pushbutton switch. The switch is effectively debounced by the reset pulse width. MR is CMOS logic compatible, so it can be driven by an external logic line. MR can be used to force a watchdog timeout to generate a reset pulse in the MAX6701(A)/MAX6702(A)/ MAX6703(A)/MAX6705(A)/MAX6706(A)/MAX6707(A) by connecting WDO to MR. Power-Fail Comparator The uncommitted power-fail comparator can be used for various purposes because its noninverting input and output are externally available. The inverting input is internally connected to a 0.62V reference. To build an early warning circuit for power failure, connect the PFI pin to a voltage-divider (see the Typical Operating Circuit). Choose the voltage-divider ratio so that the voltage at PFI falls below 0.62V just before the regulator drops out. Use PFO to interrupt the µP so it can prepare for an orderly power-down. The low-input current at this pin allows for large resistor values in the divider. VTH tWD VTH VCC +5V tRP 0V tRP +5V +5V WDO RESET 0V 0V +5V RESET +5V 0V RESET EXTERNALLY TRIGGERED BY MR MR t RP 0V +5V (RESET) 0V +5V tMD tMR +5V MR 0V WDO 0V ( ) ARE FOR MAX6702/MAX6706 ONLY. Figure 5. MAX6701/MAX6702/MAX6703/MAX6705/MAX6706/ MAX6707 Watchdog 8 Figure 6. MAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/ MAX6706(A)/MAX6707(A) RESET, MR, and WDO Timing with WDI Three-Stated _______________________________________________________________________________________ Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer WDI tWD tWD +5V tWD 0V +5V WDO R1 PFI, RST_IN1, OR RST_IN2 0V +5V RESET MAX6701(A)– MAX6708 VEXTERNAL R2 0V 0.62V t RP +5V (RESET) 0V ( MR ) VEXT-TH = 1 + R1 x 0.62V R2 +5V R1 = R2 x EXT-TH - 1) (V0.62 WHERE VEXT-TH IS THE EXTERNAL VOLTAGE TRIP LEVEL. 0V ( ) ARE FOR MAX6702(A)/MAX6706(A) ONLY. Figure 7. MAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/ MAX6706(A)/MAX6707(A) Watchdog Timing Figure 8. Calculating Adjustable Voltage Thresholds Reset Input Monitoring Other System Voltages The MAX6701(A)/MAX6702(A)/MAX6703(A) include two adjustable reset inputs for monitoring up to a total of three system voltages (including VCC). The thresholds for the monitored RST_IN supplies are externally set with resistor-divider networks (Figure 8). The reset output is asserted if any of the monitored supplies (VCC, RST_IN1, or RST_IN2) go below its specified threshold and remains asserted for the reset timeout period after all supplies are above their thresholds. Applications Information Other systems can be monitored by connecting a voltage-divider to PFI and adjusting the ratio appropriately. In noisy systems, a capacitor between PFI and GND reduces the power-fail circuit’s sensitivity to high-frequency noise on the line being monitored. Reset can be asserted on other voltages in addition to the VCC supply line. Connect PFO to MR to initiate a reset output pulse when PFI drops below 0.62V. Figure 10 shows the MAX6704–MAX6708 configured to assert a reset output when the secondary supply falls below the reset threshold. Ensuring a Valid RESET Output Down to VCC = 0 Generating a Reset from Watchdog Overflow When V CC falls below 1V, the MAX6701–MAX6708 RESET output no longer sinks current—it becomes an open circuit. High-impedance CMOS logic inputs can drift to undetermined voltages if left undriven. If a pulldown resistor is added to the RESET pin as shown in Figure 9, any stray charge or leakage currents are drained to ground, holding RESET low. A resistor value (R1) is not critical; 100kΩ is large enough not to load RESET and small enough to pull RESET to ground. This application works for push-pull output only (not for open-drain resets). Connect WDO to MR to force a watchdog timeout to generate a reset pulse for only the reset timeout period on the MAX6701(A)/MAX6702(A)/MAX6703(A)/MAX6705(A)/ MAX6706(A)/MAX6707(A). When the MAX6704 watchdog times out, reset outputs are automatically asserted (no external connections required). For the MAX6701/ MAX6702/MAX6703/MAX6705/MAX6706/MAX6707 non-A versions, do not connect WDO to MR; this creates a locked condition. _______________________________________________________________________________________ 9 MAX6701–08/MAX6701A–03A/05A–07A tWDI MAX6701–08/MAX6701A–03A/05A–07A Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer 0.9V 3.3V MAX6701(A) MAX6704 MAX6705(A) MAX6708 I/O SUPPLY RESET (RESET) VCC RESET PFI RESET µP MAX6704– MR MAX6708 PFO R1 (100kΩ) CORE SUPPLY () ARE FOR MAX6704/MAX6706(A)/MAX6708 ONLY. Figure 9. RESET Valid to Ground Circuit Figure 10. Monitoring Other System Voltages Selector Guide RESET PP LOW RESET PP HIGH RESET OD-LOW WDI WDO PFI, PFO RST_IN1, RST_IN2 MAX6701 ✔ — — ✔ ✔ PP — ✔ MAX6701A* ✔ — — ✔ ✔ PP — ✔ MAX6702 — ✔ — ✔ ✔ PP — ✔ MAX6702A* — ✔ — ✔ ✔ PP — ✔ MAX6703 — — ✔ ✔ ✔ OD — ✔ MAX6703A* — — ✔ ✔ ✔ OD — ✔ MAX6704 ✔ ✔ — ✔ — ✔ PP — MAX6705 ✔ — — ✔ ✔ PP ✔ PP — MAX6705A* ✔ — — ✔ ✔ PP ✔ PP — MAX6706 — ✔ — ✔ ✔ PP ✔ PP — MAX6706A* — ✔ — ✔ ✔ PP ✔ PP — MAX6707 — — ✔ ✔ ✔ OD ✔ OD — MAX6707A* — — ✔ ✔ ✔ OD ✔ OD — MAX6708 ✔ ✔ — — — ✔ PP — PART PP = push-pull, OD = open drain. *WDO deasserts when MR is pulled low. See the Standard- vs. A-Version Comparison section for the differences on WDO. Threshold Suffix Guide SUFFIX RESET THRESHOLD (V) L 4.63 M 4.38 T 3.08 S 2.93 R 2.63 Z 2.32 Y 2.19 Bold indicates standard version. 10 ______________________________________________________________________________________ Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer TOP VIEW MR 1 8 RESET MR 1 VCC 2 7 RESET VCC 2 GND 3 6 WDI GND 3 PFI 4 5 PFO MAX6704 MAX6705(A) MAX6706(A) MAX6707(A) PFI 4 SOT23 8 WDO MR 1 7 RESET (RESET) VCC 2 GND 6 WDI 5 PFO 8 RESET 7 RESET 3 6 N.C. PFI 4 5 PFO MAX6708 SOT23 SOT23 ( ) ARE FOR MAX6706(A) ONLY. Typical Operating Circuit PART UNREGULATED DC DC-DC REGULATOR µP VCC PUSHBUTTON SWITCH Ordering Information (continued) RESET WDI PFI MAX6705(A) WDO MAX6706(A) MR MAX6707(A) PFO VCC RESET I/O NMI INTERRUPT TEMP RANGE PIN-PACKAGE MAX6702_ KA-T -40°C to +125°C 8 SOT23-8 MAX6702A_ KA-T -40°C to +125°C 8 SOT23-8 MAX6703_ KA-T -40°C to +125°C 8 SOT23-8 MAX6703A_ KA-T -40°C to +125°C 8 SOT23-8 MAX6704_KA-T -40°C to +125°C 8 SOT23-8 MAX6705_KA-T -40°C to +125°C 8 SOT23-8 MAX6705A_KA-T -40°C to +125°C 8 SOT23-8 MAX6706_KA-T -40°C to +125°C 8 SOT23-8 MAX6706A_KA-T -40°C to +125°C 8 SOT23-8 MAX6707_KA-T -40°C to +125°C 8 SOT23-8 MAX6707A_KA-T -40°C to +125°C 8 SOT23-8 MAX6708_KA-T -40°C to +125°C 8 SOT23-8 Insert the desired suffix letter (from the Threshold Suffix Guide table) into the blank to complete the part number. All devices must be ordered in increments of 2500 pieces. Sample stock is typically held on standard versions only. Contact factory for availability. Devices are available in both leaded and lead-free packaging. Specify lead-free by replacing “-T” with “+T” when ordering. Chip Information TRANSISTOR COUNT: 716 PROCESS: BiCMOS ______________________________________________________________________________________ 11 MAX6701–08/MAX6701A–03A/05A–07A Pin Configurations (continued) Package Information (The package drawing(s) in this data sheet may not reflect the most current specifications. For the latest package outline information, go to www.maxim-ic.com/packages.) SEE DETAIL "A" SYMBOL e b C L CL E CL E1 PIN 1 I.D. DOT (SEE NOTE 6) MIN MAX A 0.90 1.45 A1 0.00 0.15 A2 0.90 1.30 b 0.22 0.38 C 0.08 0.22 D 2.80 3.00 E 2.60 3.00 E1 1.50 1.75 L 0.30 L2 0.60 0.25 BSC. e 0.65 BSC. SOT23, 8L .EPS MAX6701–08/MAX6701A–03A/05A–07A Low-Voltage, SOT23 µP Supervisors with PowerFail In/Out, Manual Reset, and Watchdog Timer 1.95 REF. e1 0¡ 0 8¡ e1 D C CL L2 A A2 GAUGE PLANE A1 SEATING PLANE C 0 L NOTE: 1. ALL DIMENSIONS ARE IN MILLIMETERS. 2. FOOT LENGTH MEASURED FROM LEAD TIP TO UPPER RADIUS OF HEEL OF THE LEAD PARALLEL TO SEATING PLANE C. 3. PACKAGE OUTLINE EXCLUSIVE OF MOLD FLASH & METAL BURR. 4. PACKAGE OUTLINE INCLUSIVE OF SOLDER PLATING. DETAIL "A" 5. COPLANARITY 4 MILS. MAX. 6. PIN 1 I.D. DOT IS 0.3 MM fl MIN. LOCATED ABOVE PIN 1. PROPRIETARY INFORMATION 7. SOLDER THICKNESS MEASURED AT FLAT SECTION OF LEAD BETWEEN 0.08mm AND 0.15mm FROM LEAD TIP. 8. MEETS JEDEC MO178 VARIATION BA. TITLE: PACKAGE OUTLINE, SOT-23, 8L BODY APPROVAL DOCUMENT CONTROL NO. REV. 21-0078 E 1 1 Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are implied. Maxim reserves the right to change the circuitry and specifications without notice at any time. 12 ____________________Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 © 2005 Maxim Integrated Products Printed USA is a registered trademark of Maxim Integrated Products, Inc.