IBM Dual Bridge and Memory Controller CPC710-100 Databook Version 1.0 December 17, 1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Copyright and Disclaimer Copyright International Business Machines Corporation 1999. All Rights Reserved Printed in the United States of America November 1999 The following are trademarks of International Business Machines Corporation in the United States, or other countries, or both. IBM IBM logo PowerPC Other company, product and service names may be trademarks or service marks of others. All information contained in this document is subject to change without notice. The products described in this document are NOT intended for use in implantation or other life support applications where malfunction may result in injury or death to persons. The information contained in this document does not affect or change IBM's product specifications or warranties. Nothing in this document shall operate as an express or implied license or indemnity under the intellectual property rights of IBM or third parties. All information contained in this document was obtained in specific environments, and is presented as an illustration. The results obtained in other operating environments may vary. THE INFORMATION CONTAINED IN THIS DOCUMENT IS PROVIDED ON AN "AS IS" BASIS. In no event will IBM be liable for damages arising directly or indirectly from any use of the information contained in this document. IBM Microelectronics Division 1580 Route 52, Bldg. 504 Hopewell Junction, NY 12533-6351 The IBM home page can be found at http://www.ibm.com The IBM Microelectronics Division home page can be found at http://www.chips.ibm.com 12/17/99 Powered by ICminer.com Electronic-Library Service CopyRight 2003 IBM Dual Bridge and Memory Controller Table of Contents Copyright and Disclaimer ...................................................................................................................... ii Table of Contents ............................................................................................................. 1 Overview ........................................................................................................................... 7 Features .................................................................................................................................................. 7 60x Bus Interface ............................................................................................................................... 7 Memory Controller ............................................................................................................................. 7 PCI-32 and PCI-64 Bus Bridges ........................................................................................................ 7 Description ............................................................................................................................................. 7 Conventions and Notation .................................................................................................................... 8 Ordering Information ............................................................................................................................. 8 System Level Block Diagram ................................................................................................................ 9 Component Block Diagram ................................................................................................................. 10 Internal Buffering and Data Flow ........................................................................................................ 11 Pin Information ............................................................................................................... 13 Pin assignment ..................................................................................................................................... 13 Pin Summary ........................................................................................................................................ 13 Signal Pins, Sorted by Pin Number .................................................................................................... 14 Signal Pins, Sorted by Signal Name ................................................................................................... 18 I/O Signals ...................................................................................................................... 23 I/O Signal Diagram ............................................................................................................................... 23 Signal Descriptions .............................................................................................................................. 24 Registers ......................................................................................................................... 34 Standard PCI Configuration Space ( register x‘00’ to x‘68’ ) ........................................................... 34 Specific PCI Host Bridges Space (BAR + x‘000F 6110’ to BAR +x‘000F 9810’) ............................. 34 System Space Address Map (x‘FF00 0000’ to x‘FFFF FFFF’) ........................................................ 34 Register Map ......................................................................................................................................... 35 Standard PCI Configuration Registers ............................................................................................... 36 Vendor ID (VID) ............................................................................................................................... 38 Device ID (DEVID) ........................................................................................................................... 38 PCI Command (CMND) ................................................................................................................... 39 PCI Status (STAT) ........................................................................................................................... 41 Revision ID (RID) ............................................................................................................................. 43 Programming Interface (SPI) ........................................................................................................... 43 Sub-Class Code (SUBC) ................................................................................................................. 44 Base Class Code (CLASS) .............................................................................................................. 45 Cache Line Size (CSIZE) ................................................................................................................ 46 Latency Timer (LTIM) ...................................................................................................................... 47 Header Type (HDRT) ...................................................................................................................... 48 Built in Self Test (BIST) ................................................................................................................... 49 System Base Address Register for PCI-64 (PSBAR) ...................................................................... 50 Interrupt Line (INTLN) ...................................................................................................................... 51 CPC710TOC.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 1 of 209 IBM Dual Bridge and Memory Controller Interrupt Pin (INTPIN) ......................................................................................................................52 Minimum Grant (MINGNT) ...............................................................................................................53 Maximum Latency (MAXLT) ............................................................................................................54 Bus Number (BUSNO) .....................................................................................................................55 Subordinate Bus Number (SUBNO) ................................................................................................56 Disconnect Counter (DISCNT) .........................................................................................................57 Retry Counter (RETRY) ...................................................................................................................58 Deadlock Retry Counter (DLKRETRY) ............................................................................................59 Semaphore (PSEM) .........................................................................................................................60 Set Addressed Interrupt (IT_ADD_SET) ..........................................................................................61 Reset PCI-64 Interrupt (INT_RESET) ..............................................................................................62 Specific PCI Host Bridge Registers ....................................................................................................63 PCI Slave Error Address Register (PSEA) ......................................................................................64 PCI Diagnostic Register (PCIDG) ....................................................................................................65 Interrupt Acknowledge Cycle (INTACK) ...........................................................................................66 PCI Base Address for I/O (PIBAR) ..................................................................................................67 PCI Base Address for Memory (PMBAR) ........................................................................................68 Component Reset Register (CRR) ..................................................................................................69 Personalization Register (PR) ..........................................................................................................70 Arbiter Control Register (ACR) ........................................................................................................72 PCI Memory Address Space Size (MSIZE) .....................................................................................73 PCI I/O Address Space Size (IOSIZE) .............................................................................................74 System Base Address for PCI Memory (SMBAR) ...........................................................................75 System Base Address for PCI I/O (SIBAR) .....................................................................................76 PHB Configuration Register (CTLRW) ............................................................................................77 PHB Configuration Register (CTLRO) .............................................................................................78 CONFIG_ADDRESS Register (CFGA) ............................................................................................79 CONFIG_DATA Register (CFGD) ...................................................................................................80 System Address Space SIZE for PCI (PSSIZE) ..............................................................................81 Other PCI Address Space SIZE for PCI (PPSIZE) ..........................................................................82 System Base Address Register (BARPS) ........................................................................................83 System Base Address Register for PCI-32 (PSBAR) ......................................................................84 Bottom of Peripheral Memory Space With Potential Deadlock (BPMDLK) ......................................85 Top of Peripheral Memory Space With Potential Deadlock (TPMDLK) ...........................................86 Bottom of Peripheral I/O Space With Potential Deadlock (BIODLK) ...............................................87 Top of Peripheral I/O Space With Potential Deadlock (TIODLK) .....................................................88 Reset Addressed Interrupt Register (IT_ADD_RESET) ..................................................................89 Set PCI-64 Interrupt Register (INT_SET) ........................................................................................90 Channel Status Register (CSR) .......................................................................................................91 Processor Load/Store Status Register (PLSSR) .............................................................................92 Standard System Registers Space .....................................................................................................93 Physical Identifier Register (PIDR) ..................................................................................................96 Connectivity Configuration Register (CNFR) ...................................................................................97 Connectivity Reset Register (RSTR) ...............................................................................................98 Software Power On Reset Control Register (SPOR) .......................................................................99 Specific System Registers Space .....................................................................................................100 CPC710 & System Control (UCTL) ................................................................................................100 Multi-Processor Semaphore (MPSR) .............................................................................................102 System I/O Control (SIOC) ............................................................................................................103 -60x Arbiter Control Register (ABCNTL) ........................................................................................104 CPU Soft Reset Register (SRST) ..................................................................................................106 Page 2 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710TOC.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Error Control Register (ERRC) ...................................................................................................... 107 System Error Status Register (SESR) ........................................................................................... 108 System Error Address Register (SEAR) ........................................................................................ 110 Chip Programmability Register (PGCHP) ...................................................................................... 111 Free Register 1 (RGBAN1) ............................................................................................................ 113 Free Register 2 (RGBAN2) ............................................................................................................ 114 GPIO Direction Register (GPDIR) ................................................................................................. 115 GPIO Input Value Register (GPIN) ............................................................................................... 116 GPIO Output Value Register (GPOUT) ......................................................................................... 117 Address Transfer Attribute for Snoop Register (ATAS) ................................................................. 118 Diagnostic Register (AVDG) .......................................................................................................... 119 Memory Controller Control Register (MCCR) ................................................................................ 121 Memory Error Status Register (MESR) ......................................................................................... 123 Memory Error Address Register (MEAR) ...................................................................................... 124 Memory Configuration Extent Registers (MCER[0:7]) ................................................................... 125 System I/O Register 0 (SIOR0) ..................................................................................................... 127 System I/O Register 1 (SIOR1) ..................................................................................................... 128 DMA Registers Space ........................................................................................................................ 129 DMA Global Control (GSCR) ......................................................................................................... 129 DMA Global Status (GSSR) .......................................................................................................... 130 DMA Transfer Control (XSCR) ...................................................................................................... 131 DMA Transfer Status (XSSR) ........................................................................................................ 132 DMA Transfer PCI Address (XPAR) .............................................................................................. 134 DMA Transfer Write Back Address (XWAR) ................................................................................. 135 DMA Transfer Translated Address (XTAR) ................................................................................... 136 System Standard Configuration Registers Space .......................................................................... 137 Device Characteristics Register (DCR) ......................................................................................... 137 Device ID Register (DID) ............................................................................................................... 138 Base Address Register (BAR) ....................................................................................................... 139 Device Specific Configuration Space ............................................................................................ 140 PCI BAR Enable Register (PCIENB) ............................................................................................. 140 Addressing Model ....................................................................................................... 143 Address Maps ..................................................................................................................................... 143 CPU to PCI Addressing Model .......................................................................................................... 144 PREP and FPHB Modes ............................................................................................................... 144 Peripheral I/O Address Translation ............................................................................................... 145 PCI to System Memory ...................................................................................................................... 146 PowerPC Reference Platform (PREP) Mode ................................................................................ 146 PCI Master Address Operation ............................................................................................... 146 Translation Enabled ................................................................................................................ 147 Translation Disabled ............................................................................................................... 147 Flexible PCI Host Bridge (FPHB) Mode ........................................................................................ 148 60x Interface ................................................................................................................. 149 Overview ............................................................................................................................................. 149 Endian Support .................................................................................................................................. 149 Processor Behavior in LE Mode .................................................................................................... 149 Endian Behavior ............................................................................................................................ 149 60x Bus Arbiter Description .............................................................................................................. 152 CPC710TOC.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 3 of 209 IBM Dual Bridge and Memory Controller Rotating Priority Resolution ...........................................................................................................152 Address Bus Pipelining ..................................................................................................................152 Arbiter Requirements .....................................................................................................................153 Internal ABB........................................................................................................................... 153 Qualified SYS_BG Equation ................................................................................................. 153 SYS_TS Assertion ................................................................................................................. 153 SYS_BR Negation.................................................................................................................. 153 Qualified SYS_DBG Equation............................................................................................... 153 High Impedance After SYS_TEA .......................................................................................... 153 SYS_DRTRY Assertion ......................................................................................................... 153 Slave Data Bus Determination ............................................................................................. 154 SYS_L2_Hit Assertion........................................................................................................... 154 Bus Enhancements ........................................................................................................................155 DBB not Required by Masters ................................................................................................. 155 Half-Cycle Precharge not Required on SYS_TA................................................................. 155 Half-Cycle Precharge not Required on SYS_TEA .............................................................. 155 SYS_ARTRY_PREV in QDBG Equation Eliminated............................................................ 155 60x Bus Transfer Types and Sizes ................................................................................................156 Data Gathering ....................................................................................................................................158 SYNC and EIEIO .................................................................................................................................159 Address Retry (SYS_ARTRY) ............................................................................................................159 Precharging SYS_ARTRY and SYS_SHD ......................................................................................................... 159 SYS_ARTRY Assertions ................................................................................................................159 Recommended SYS_ARTRY Procedure .......................................................................................159 Locking Signal DLK .......................................................................................................................................................... 160 60x Bus Configuration .......................................................................................................................161 Error Handling for CPU-Initiated Transactions ...............................................................................162 Checkstop Errors ...........................................................................................................................162 Memory Controller ....................................................................................................... 167 Overview .............................................................................................................................................167 Bank Definitions .................................................................................................................................169 SDRAM Banks ...............................................................................................................................169 DIMM Banks ..................................................................................................................................170 Interleaved Banks ..........................................................................................................................171 Memory Signal Connections .............................................................................................................172 SDRAM Subsystem Overview ...........................................................................................................174 Supported SDRAM Organizations ....................................................................................................175 SDRAM Buffering Requirements ...................................................................................................175 Memory Controller Registers ............................................................................................................178 MCCR Register ..............................................................................................................................178 MCER Register ..............................................................................................................................180 Error Handling ....................................................................................................................................182 Single-Bit ECC Error, General Case ..............................................................................................182 Single-Bit ECC Error, Special Case ...............................................................................................182 Invalid Address Error .....................................................................................................................182 Double-Bit ECC Error, General Case ............................................................................................182 Double-Bit ECC Error, Special Case .............................................................................................183 Overlapping Memory Extents .........................................................................................................183 Page 4 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710TOC.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Bridges ................................................................................................................... 185 Overview ............................................................................................................................................. 185 Address Map ....................................................................................................................................... 185 System Standard Configuration Registers ...................................................................................... 186 System PHB Registers ...................................................................................................................... 186 PCI Bus Commands ........................................................................................................................... 187 PCI Master Memory Read Cycles ................................................................................................. 188 PCI Master Memory Write Cycles ................................................................................................. 189 Configuration Cycles ..................................................................................................................... 190 TYPE 0 Configuration Cycles.................................................................................................. 190 Type 1 Configuration Cycles ................................................................................................... 191 PCI Address/Data Bus for TYPE 0 Configuration Cycles ............................................................... 191 PCI Performance Estimates .............................................................................................................. 192 PCI Master Error Handling ................................................................................................................ 193 System I/O Interface .................................................................................................... 197 Configuration ...................................................................................................................................... 197 System I/O Registers: Application Presence Detect Bits ............................................................... 197 Flash Interface and Presence Detect Bits ........................................................................................ 197 Boot ROM ...................................................................................................................................... 197 DMA Controller ............................................................................................................. 199 Introduction ........................................................................................................................................ 199 DMA Transfer Registers .................................................................................................................... 200 DMA Transfer Status Cache Line .................................................................................................. 201 DMA Procedure .................................................................................................................................. 202 Special Boundary Conditions ........................................................................................................ 203 Initialization .................................................................................................................. 205 Power Up Sequence ........................................................................................................................... 205 POWERGOOD Power-On Reset ........................................................................................................ 205 Typical Register setup sequence ..................................................................................................... 206 Timing Diagrams .......................................................................................................... 209 CPU to Memory .................................................................................................................................. 209 Read Page Hit from PowerPC CPU to SDRAM ................................................................................ 209 Read Page Miss from PowerPC CPU to SDRAM ............................................................................. 210 Write Burst Page Hit from PowerPC CPU to SDRAM ..................................................................... 211 Write Burst Page Miss from PowerPC CPU to SDRAM .................................................................. 212 Write One Byte to Memory from CPU: Read Modify Write ............................................................. 213 CPU Access to the Boot ROM ........................................................................................................... 214 Read of One Byte from the Boot ROM ............................................................................................. 214 Write of One Byte to the Boot Flash ................................................................................................. 214 PCI-64 external Master accessing the SDRAM Memory ............................................................... 215 ....................................................................................................................................................... 215 READ 32 Bytes from the SDRAM by a PCI Master on PCI 64- 66MHz bus: .................................. 215 CPC710TOC.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 5 of 209 IBM Dual Bridge and Memory Controller Write of 32 Bytes in the SDRAM from a PCI Master on the PCI 64- 66MHz bus ...........................216 Electrical Specifications ............................................................................................. 218 Absolute Maximum Ratings ..............................................................................................................218 Recommended DC Operating Conditions ........................................................................................218 Driver/Receiver Specifications ..........................................................................................................219 Thermal Specifications ......................................................................................................................219 AC Timing Specifications ..................................................................................................................220 60x Bus Timings .................................................................................................................................220 PCI Bus Timings .................................................................................................................................221 SDRAM Interface Timings .............................................................................................................222 Packaging Information ................................................................................................ 223 Package Dimensions .........................................................................................................................223 References ................................................................................................................... 224 Revision Log .......................................................................................................................................225 Page 6 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710TOC.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Overview Features • • • • • • • • • • • • • • Up to 100 MHz PowerPC 60x 64-bit bus Supports 100 MHz SDRAM including PC100 I/O for up to 2 MB 8-bit flash ROM 32-bit 33 MHz/64-bit 33-66 MHz async dual bus Reads two external 32-bit registers Pr*P-compliant design (bi-endian and t=0 only) One-channel DMA controller 3.3 volts ± 5%; 5 volt-compliant I/O -20 to 105°C junction temperature Power dissipation 2.1 watts typical at 3.3 volts CBGA package; 625 pins, 32x32mm CMOS 5S6, 0.35µm technology (9.0x9.05mm) PLL to reduce on-chip system clock skew JTAG controller (LSSD design) 60x Bus Interface • 100 MHz external bus operation • Supports two processor or L2 lookaside cache • Supports 604e or 750 PowerPC direct-attach • Dual 32-byte store back buffers • High bandwidth 2-way arbiter • Little Endian mode in 604e or 750 PowerPC • Supports SYNC/EIEIO ordering operations • Supports 60x bus configuration cycles • Multiprocessor bringup semaphore bits • Single load on all buses Memory Controller • Up to 2GB • 2-way interleaved SDRAM with ECC • Supports 16, 64, 128, and 256 MB DRAMs • Programmable timing parameters • Up to 8 dual bank DIMM • Controls external MUX to reduce pin count • 4-entry command queue; look ahead override • Three separate dual 32-byte load buffers (PCI32, PCI-64, 60x) • Supports 32-byte cache line reload PCI-32 and PCI-64 Bus Bridges • Two independent PCI bus bridges with parking • PCI revision 2.1 compliant • Compliant with 5.0 V PCI signalling • Runs async logic to 60x and memory controller • PCI-64 arbitration can be disabled • Dual 32-byte buffers in each PCI bus bridge • Round-robin PCI arbiter • Supports slave fast back-to-back transfers • Coherency for DMA access to system memory • Noncontiguous byte enable transfer to memory • Single load on all PCI signals Description The IBM25CPC710AB3A100 is a highly integrated host bridge device that interfaces a PowerPC 60x bus with SDRAM-based system memory and two PCI ports. It provides arbitration for one or two processors and supports two levels of pipelining per processor along with 64-byte buffers. The device’s memory controller supports SDRAM, allowing the memory to burst data on almost every bus cycle at 100 MHz (1-2-1-1 after initial latency). CPC710_First.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 For system designs requiring high I/O bandwidth, the device contains two PCI host bus bridges. One bridge supports a standard 32-bit, 33 MHz PCI bus for standard and native I/O. The other bridge supports a 64-bit, 33-66 MHz PCI bus for high data throughput applications such as graphics and highspeed communications. A DMA controller provides high speed capability for large data transfers between memory and I/O. Store-gathering enhances CPU-to-I/O performance. Page 7 of 209 IBM Dual Bridge and Memory Controller Ordering Information Part Number Operating Speed IBM25CPC710AB3A100 100 MHz Description IBM Dual Bridge and Memory Controller Conventions and Notation The use of overbars, for example RESET, designates signals that are active low. All signals are active high unless shown with an overbar. Decimal, hexadecimal, and binary numbers are used throughout this document, and are labeled as follows: Decimal: 1234.56 Hexadecimal: x’ABCD’ Binary: b‘0101’ LSB MSB In Little Endian mode, bits and bytes are numbered in descending order from left to right. The most significant bit (MSB) has the highest number and the least significant bit (LSB) has the lowest number: 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 0 LSB MSB In Big Endian mode, bits and bytes are numbered in ascending order from left to right. The most significant bit (MSB) has the lowest number and the least significant bit (LSB) has the highest number: 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Page 8 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_First.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System Level Block Diagram Optional 2nd CPU* L2 Cache L2 Cache PowerPC 604/750 PowerPC 604/750 64 60x System Bus, 100 MHz 2 4 6 DIMM DIMM DIMM DIMM IBM25CPC710AB3A100 0 PCI-64 Bus, 66 MHz DMA 72 Memory Controller PCI Bridges 72 Pair 0 System I/O 1 3 5 7 DIMM DIMM DIMM DIMM MUX ECC PCI-32 Bus, 33 MHz 72 100 MHz DRAMs, up to 2GB xcvr Flash PD Regs *The IBM25CPC710AB3A100 is designed to interface with 60x system bus definition. It can also directly interface to one or two PowerPC 604/750 processors. CPC710_First.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 9 of 209 IBM Dual Bridge and Memory Controller Component Block Diagram 60x Bus Interface Logic 60x Address Queueing Address Decodes Arbiter JTAG Controller Endian Translation JTAG Interface Configuration Internal Device Interface Posted Store Buffers Memory DMA PCI-32 PCI-64 Reset Logic Clock Logic CACHE OP INTF Command Queues ECC Correction 60X PCI-32 DMA Controller Logic PCI-64 Control Logic DMA Data Buffers 60x PCI-32 FLASH ROM Interface MEMORY PCI-32 PCI-64 PCI-32 Bus Interface Memory DMA Async Boundary DMA External Registers Interface 60x PCI-64 Bus Interface Internal Device Interface Internal Device Interface System I/O Control Internal Device Interface PCI Bus Master/Slave Logic 60x PCI-64 Data Buffers Memory Async Boundary MEM INTF Internal Device Interface SDRAM Internal Device Interface SDRAM Memory Controller PCI Bus Master/Slave Logic Data Buffers IBM25CPC710AB3A100 Clocked at System Bus Speed (100 MHz) Clocked at PCI-32 Bus Speed (33 MHz) Clocked at PCI-64 Bus Speed (33-66 MHz) Dual Clocked Logic Page 10 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_First.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Internal Buffering and Data Flow 60x Bus 60x Bus Interface Logic I/O LE Byte Swap BE LE Byte Swap 64 bytes System Bus Clock 66 MHz CLK Memory Bus PCI-64 Bus 64 bytes System Bus Clock I/O S W A P 64 bytes PCI-64 Bridge Logic 64 bytes I/O 64 bytes PCI-32 Bridge Logic 32 bytes SIO I/O 64 bytes Rotating priority S W A P Memory Control Logic 33 MHz CLK PCI-32 Bus System Bus Clock CPC710_First.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 DMA Controller Page 11 of 209 IBM Dual Bridge and Memory Controller Page 12 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_First.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Pin Information Pin assignment (Top View Through Ceramic) For specific pin assignments, see Signal Pins, Sorted by Pin Number on page 14 and Signal Pins, Sorted by Signal Name on page 18. 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 AE AD AC AB AA 0Y 0W 0V 0U 0T 0R 0P 0N 0M 0L 0K 0J 0H 0G 0F 0E 0D 0C 0B 0A No Connect VDD Ground I/O Signal Pin Summary Pin Type Number of Pins VDD 62 Ground 54 Test Pins 20 No Connect 8 Total Module Signal I/Os 480 Total Pins 625 CPC710_Pins.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 13 of 209 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Pin Number Pin Signal Pin (Page 1 of 4) Signal Pin Signal Pin Signal 0A01 Locator 0B15 G_ADL25 0D04 MUX_CLKENA2 0E18 G_ADH6 0A02 VDD 0B16 TESTIN 0D05 MDATA67 0E19 G_ADH27 0A03 No Connect 0B17 VDD 0D06 G_ARB 0E20 G_ADH17 0A04 WE2 0B18 G_ADH11 0D07 MADDR3 0E21 VDD 0A05 MUX_CLKEN1B 0B19 G_CBE0 0D08 MUX_SEL 0E22 G_ADH19 0A06 MADDR9 0B20 G_ADH10 0D09 MUX_OEA 0E23 INT2 0A07 MADDR7 0B21 VDD 0D10 SCAN_GATE 0E24 VDD 0A08 MUX_CLKEN2B 0B22 G_ADL16 0D11 G_REQ1 0E25 G_PAR64 0A09 MUX_OEB 0B23 G_ADH30 0D12 G_GNT3 0F01 MDATA50 0A10 G_INTB 0B24 Ground 0D13 Ground 0F02 MDATA49 0A11 G_RST 0B25 VDD 0D14 PCG_CLK 0F03 SDCS6 0A12 G_IRDY 0C01 No Connect 0D15 G_ADL26 0F04 MADDR12 0A13 G_GNT0 0C02 SDCKE3 0D16 G_ADL30 0F05 MDATA61 0A14 G_STOP 0C03 Ground 0D17 G_ADL27 0F06 SDCKE5 0A15 G_ADL31 0C04 MADDR11 0D18 G_ADH0 0F07 MDATA70 0A16 G_CBE7 0C05 SYS_HRESET0 0D19 G_CBE2 0F08 G_REQ64 0A17 G_CBE6 0C06 PRES_OE1 0D20 P_ADL20 0F09 SDCKE2 0A18 G_CBE3 0C07 Ground 0D21 G_ADH16 0F10 CHKSTOP 0A19 G_CBE1 0C08 FLASH_OE 0D22 G_ADH28 0F11 G_REQ0 0A20 G_ADL17 0C09 G_REQ4 0D23 G_ADH24 0F12 G_CFG2 0A21 G_ADH12 0C10 MADDR5 0D24 G_ADL15 0F13 VDD 0A22 G_PERR 0C11 Ground 0D25 G_ADH23 0F14 G_ADL20 0A23 No Connect 0C12 G_FRAME 0E01 MDATA48 0F15 G_ADL21 0A24 VDD 0C13 G_INTC 0E02 VDD 0F16 CE0_IO 0A25 Ground 0C14 G_TRDY 0E03 MDATA37 0F17 G_ADH2 0B01 VDD 0C15 Ground 0E04 SDCKE1 0F18 G_GNT5 0B02 Ground 0C16 G_CBE4 0E05 VDD 0F19 G_ADH13 0B03 SDCKE7 0C17 G_ADL19 0E06 SDCKE6 0F20 G_ADH26 0B04 WE1 0C18 G_ADL18 0E07 WE3 0F21 G_ADL4 0B05 VDD 0C19 Ground 0E08 MADDR2 0F22 G_ADH29 0B06 MADDR10 0C20 G_ADL29 0E09 VDD 0F23 G_ADH22 0B07 MADDR8 0C21 G_CBE5 0E10 MADDR4 0F24 G_ADL14 0B08 MADDR6 0C22 G_ADH31 0E11 MUX_CLKENA1 0F25 G_ADL13 0B09 VDD 0C23 Ground 0E12 G_DEVSEL 0G01 MDATA43 0B10 PLL_LOCK 0C24 G_ADH25 0E13 G_GNT1 0G02 MDATA52 0B11 G_GNT2 0C25 No Connect 0E14 G_ADL22 0G03 Ground 0B12 PRES_OE0 0D01 MDATA47 0E15 G_ADH5 0G04 SDCS14 0B13 VDD 0D02 MDATA65 0E16 G_ADH4 0G05 MADDR0_ODD 0B14 G_ADL23 0D03 MDATA66 0E17 VDD 0G06 MDATA45 Page 14 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pins.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Pin Number Pin Signal Pin (Page 2 of 4) Signal Pin Signal Pin Signal 0G07 Ground 0H21 G_ADL6 0K10 SDCAS0 0L24 P_ADL12 0G08 MDATA69 0H22 G_ADL8 0K11 SDCAS1 0L25 P_ADL17 0G09 WE0 0H23 G_PAR 0K12 G_REQ5 0M01 SDCS1 0G10 MADDR0_EVEN 0H24 G_ADL9 0K13 VDD 0M02 CE0_TEST 0G11 Ground 0H25 Ground 0K14 VDD 0M03 SDCS9 0G12 G_REQ3 0J01 MDATA57 0K15 SYS_BR2 0M04 RI 0G13 G_LOCK 0J02 VDD 0K16 G_ADH18 0M05 SDCS8 0G14 G_ACK64 0J03 MDATA54 0K17 SYS_BR3 0M06 CE1_C2 0G15 Ground 0J04 SDCS11 0K18 P_ADL24 0M07 MDATA7 0G16 G_ADH8 0J05 VDD 0K19 FLASH_WE 0M08 CE1_B 0G17 G_ADL0 0J06 MDATA56 0K20 SYS_CLK 0M09 SDRAS0 0G18 G_ADH14 0J07 SDCKE0 0K21 Ground 0M10 SDRAS1 0G19 Ground 0J08 MDATA63 0K22 VDDA 0M11 PLL_RESET 0G20 G_ADL3 0J09 VDD 0K23 P_ADL23 0M12 VDD 0G21 G_ADL5 0J10 MADDR1 0K24 P_ADL22 0M13 RESERVED2 0G22 XADR_LAT 0J11 G_GNT4 0K25 P_ADL18 0M14 VDD 0G23 Ground 0J12 SDCAS2 0L01 SDCS0 0M15 P_CFG0 0G24 G_ADL12 0J13 SDCAS3 0L02 SDCS10 0M16 TESTOUT 0G25 G_ADL11 0J14 G_SERR 0L03 Ground 0M17 P_ADL25 0H01 MDATA42 0J15 G_ADH3 0L04 SDCS12 0M18 P_ADL28 0H02 MDATA41 0J16 G_ADH7 0L05 MDATA40 0M19 P_ADL16 0H03 MDATA36 0J17 VDD 0L06 SDCS13 0M20 TMS 0H04 MDATA55 0J18 G_ADL2 0L07 Ground 0M21 P_REQ5 0H05 MDATA60 0J19 G_ADH20 0L08 SDCS15 0M22 P_ADL15 0H06 SDCS7 0J20 P_ADL21 0L09 MDATA59 0M23 P_REQ4 0H07 MDATA46 0J21 VDD 0L10 SDCKE4 0M24 P_ADL14 0H08 MDATA64 0J22 XCVR_RD 0L11 Ground 0M25 P_REQ3 0H09 MDATA68 0J23 P_RST 0L12 RESERVED3 0N01 SDCS2 0H10 MDATA71 0J24 VDD 0L13 RESERVED5 0N02 VDD 0H11 G_CFG0 0J25 G_ADL7 0L14 Ground 0N03 SDCS5 0H12 G_CFG1 0K01 MDATA58 0L15 Ground 0N04 Ground 0H13 G_ADL24 0K02 CE1_C1 0L16 G_ADL10 0N05 SDCS3 0H14 G_ADL28 0K03 MDATA53 0L17 P_ADL19 0N06 VDD 0H15 G_ADH1 0K04 P_GNT6 0L18 P_ADL27 0N07 MDATA10 0H16 G_ADH9 0K05 MDATA39 0L19 Ground 0N08 MDATA9 0H17 G_ADH15 0K06 CE1_A 0L20 P_ADL29 0N09 MDATA38 0H18 G_ADL1 0K07 MDATA51 0L21 P_ADL30 0N10 VDD 0H19 G_ADH21 0K08 MDATA44 0L22 P_ADL13 0N11 SDRAS2 0H20 G_REQ6 0K09 MDATA62 0L23 Ground 0N12 SYS_CONFIG0 CPC710_Pins.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 15 of 209 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Pin Number Pin Signal Pin (Page 3 of 4) Signal Pin Signal Pin Signal 0N13 Ground 0R02 MDATA11 0T16 PLL_TUNE1 0V05 MDATA28 0N14 SYS_CONFIG1 0R03 Ground 0T17 P_GNT3 0V06 MDATA30 0N15 P_CFG1 0R04 MDATA12 0T18 P_GNT4 0V07 MDATA1 0N16 VDD 0R05 MDATA22 0T19 P_GNT_0 0V08 SYS_TT3 0N17 P_ADL26 0R06 MDATA35 0T20 P_MEMREQ 0V09 SYS_DATAP2 0N18 P_ADL8 0R07 Ground 0T21 P_GNT1 0V10 SYS_DATAP0 0N19 P_ADL10 0R08 MDATA29 0T22 P_MEMACK 0V11 SYS_DATA29 0N20 VDD 0R09 MDATA33 0T23 G_REQ7 0V12 SYS_DATA37 0N21 G_GNT7 0R10 BS0 0T24 P_ADL0 0V13 SYS_DATA60 0N22 Ground 0R11 Ground 0T25 P_CBE2 0V14 SYS_DATA4 0N23 P_ADL31 0R12 VDD 0U01 MDATA31 0V15 SYS_DATA53 0N24 VDD 0R13 RESERVED4 0U02 VDD 0V16 SYS_ADDR2 0N25 P_ADL11 0R14 Ground 0U03 MDATA32 0V17 SYS_ADDR0 0P01 MDATA13 0R15 Ground 0U04 MDATA8 0V18 SYS_ADDR26 0P02 PCI_CLK 0R16 PLL_TUNE0 0U05 VDD 0V19 SYS_ADDR25 0P03 MDATA14 0R17 P_CBE3 0U06 MDATA18 0V20 P_DEVSEL 0P04 TDI 0R18 P_LOCK 0U07 MDATA0 0V21 G_RESETOUT 0P05 MDATA15 0R19 Ground 0U08 MDATA2 0V22 P_PERR 0P06 TCK 0R20 P_ADL4 0U09 VDD 0V23 SYS_ADDR31 0P07 SYS_HRESET1 0R21 P_GNT2 0U10 SYS_DATA16 0V24 SYS_ADDR16 0P08 TRST 0R22 P_ADL3 0U11 SYS_DATA28 0V25 SYS_ADDR22 0P09 SDCS4 0R23 Ground 0U12 O_GPIO1 0W01 SYS_DBG1 0P10 BS1 0R24 P_ADL7 0U13 O_GPIO0 0W02 SYS_AACK 0P11 SDRAS3 0R25 P_PAR 0U14 VDD 0W03 Ground 0P12 VDD 0T01 MDATA16 0U15 SYS_DATA48 0W04 MDATA6 0P13 RESERVED6 0T02 POWERGOOD 0U16 RESERVED1 0W05 SYS_TSIZ1 0P14 VDD 0T03 MDATA26 0U17 VDD 0W06 SYS_DBG0 0P15 P_CFG2 0T04 DI1 0U18 P_GNT5 0W07 Ground 0P16 VDD 0T05 MDATA25 0U19 G_IDSEL 0W08 SYS_DATAP1 0P17 VDD 0T06 DI2 0U20 SYS_ADDRP1 0W09 SYS_DATAP3 0P18 P_CBE0 0T07 MDATA3 0U21 VDD 0W10 SYS_DATA17 0P19 P_REQ2 0T08 MDATA20 0U22 P_ADL9 0W11 Ground 0P20 P_ADL1 0T09 MDATA19 0U23 P_SERR 0W12 SYS_DATA38 0P21 P_REQ1 0T10 MDATA27 0U24 VDD 0W13 SYS_DATA61 0P22 P_ADL2 0T11 Ground 0U25 P_CBE1 0W14 G_GNT6 0P23 P_REQ0 0T12 P_REQ6 0V01 MDATA24 0W15 Ground 0P24 P_ADL6 0T13 VDD 0V02 MDATA23 0W16 SYS_ADDR3 0P25 P_ISA_MASTER 0T14 CE_TRST 0V03 MDATA4 0W17 SYS_ADDRP3 0R01 MDATA5 0T15 Ground 0V04 MDATA17 0W18 SYS_ADDR9 Page 16 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pins.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Pin Number Pin Signal Pin (Page 4 of 4) Signal Pin Signal Pin Signal 0W19 Ground AA09 VDD AB23 SYS_ADDR29 AD12 SYS_DATA62 0W20 SYS_ADDR24 AA10 SYS_DATA10 AB24 SYS_ADDR28 AD13 VDD 0W21 SYS_ADDR10 AA11 SYS_DATA11 AB25 SYS_ADDR27 AD14 SYS_DATA56 0W22 P_STOP AA12 SYS_ARTRY AC01 No Connect AD15 SYS_DATA7 0W23 Ground AA13 SYS_DATA57 AC02 DLK AD16 SYS_DATA52 0W24 SYS_ADDR20 AA14 SYS_TS AC03 Ground AD17 VDD 0W25 SYS_ADDR21 AA15 SYS_DATA58 AC04 SYS_DATAP6 AD18 SYS_DATA44 0Y01 SYS_BG0 AA16 SYS_DATA1 AC05 SYS_SHD AD19 SYS_ADDR5 0Y02 SYS_BG1 AA17 VDD AC06 SYS_DATA34 AD20 SYS_ADDR7 0Y03 MDATA34 AA18 SYS_DATA46 AC07 Ground AD21 VDD 0Y04 SYS_MACHK0 AA19 SYS_DATA0 AC08 SYS_DATA33 AD22 SYS_ADDR12 0Y05 MDATA21 AA20 G_INTD AC09 SYS_DATA27 AD23 SYS_ADDR14 0Y06 SYS_TT2 AA21 VDD AC10 SYS_DATA25 AD24 Ground 0Y07 SYS_DATA19 AA22 PLN_RTC_CLK AC11 Ground AD25 VDD 0Y08 O_GPIO2 AA23 P_TRDY AC12 SYS_L2_HIT AE01 Ground 0Y09 RESERVED8 AA24 VDD AC13 SYS_DATA59 AE02 VDD 0Y10 SYS_SRESET1 AA25 SYS_ADDR17 AC14 SYS_TA AE03 No Connect 0Y11 SYS_DATA35 AB01 SYS_TSIZ2 AC15 Ground AE04 SYS_MACHK1 0Y12 TDO AB02 SYS_TBST AC16 INT1 AE05 SYS_DATA21 0Y13 VDD AB03 NODLK AC17 SYS_DATA51 AE06 SYS_DATA22 0Y14 SYS_TBE AB04 SYS_TT1 AC18 SYS_DATA42 AE07 SYS_DATA14 0Y15 SYS_DATA41 AB05 SYS_DATAP7 AC19 Ground AE08 SYS_DATA13 0Y16 SYS_SRESET0 AB06 SYS_TEA AC20 SYS_DATA3 AE09 SYS_DATA30 0Y17 SYS_DATA49 AB07 SYS_DATA12 AC21 G_REQ2 AE10 SYS_DATA31 0Y18 P_FRAME AB08 RESERVED7 AC22 SYS_ADDR13 AE11 SYS_DATA32 0Y19 SYS_ADDR1 AB09 SYS_DATA36 AC23 Ground AE12 SYS_BR1 0Y20 SYS_ADDRP2 AB10 SYS_DATA9 AC24 SYS_ADDR30 AE13 G_INTA 0Y21 SYS_ADDR23 AB11 SYS_DATA8 AC25 No Connect AE14 SYS_BR0 0Y22 SYS_ADDR15 AB12 SYS_DATA39 AD01 VDD AE15 SYS_DATA43 0Y23 P_ADL5 AB13 Ground AD02 Ground AE16 SYS_DATA55 0Y24 SYS_ADDR18 AB14 SYS_DATA40 AD03 SYS_DATAP5 AE17 SYS_DATA50 0Y25 SYS_ADDR19 AB15 SYS_DATA6 AD04 SYS_DATAP4 AE18 SYS_DATA45 AA01 SYS_TSIZ0 AB16 SYS_DATA2 AD05 VDD AE19 SYS_ADDR4 AA02 VDD AB17 SYS_DATA5 AD06 SYS_DATA18 AE20 SYS_ADDR6 AA03 VDD AB18 SYS_DATA54 AD07 SYS_DATA23 AE21 SYS_ADDR8 AA04 SYS_TT4 AB19 SYS_DATA47 AD08 SYS_DATA24 AE22 SYS_ADDR11 AA05 VDD AB20 P_IRDY AD09 VDD AE23 No Connect AA06 SYS_TT0 AB21 SYS_GBL AD10 SYS_DATA26 AE24 VDD AA07 SYS_DATA20 AB22 SYS_ADDRP0 AD11 SYS_DATA63 AE25 Ground AA08 SYS_DATA15 CPC710_Pins.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 17 of 209 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Signal Name Signal Pin Signal (Page 1 of 4) Pin Signal Pin Signal Pin BS0 0R10 G_ADH23 0D25 G_ADL30 0D16 G_REQ5 0K12 BS1 0P10 G_ADH24 0D23 G_ADL31 0A15 G_REQ6 0H20 CE_TRST 0T14 G_ADH25 0C24 G_ARB 0D06 G_REQ7 0T23 CE0_IO 0F16 G_ADH26 0F20 G_CBE0 0B19 G_REQ64 0F08 CE0_TEST 0M02 G_ADH27 0E19 G_CBE1 0A19 G_RESETOUT 0V21 CE1_A 0K06 G_ADH28 0D22 G_CBE2 0D19 G_RST 0A11 CE1_B 0M08 G_ADH29 0F22 G_CBE3 0A18 G_SERR 0J14 CE1_C1 0K02 G_ADH30 0B23 G_CBE4 0C16 G_STOP 0A14 CE1_C2 0M06 G_ADH31 0C22 G_CBE5 0C21 G_TRDY 0C14 CHKSTOP 0F10 G_ADL0 0G17 G_CBE6 0A17 Ground 0A25 DI1 0T04 G_ADL1 0H18 G_CBE7 0A16 Ground 0B02 DI2 0T06 G_ADL2 0J18 G_CFG0 0H11 Ground 0B24 DLK AC02 G_ADL3 0G20 G_CFG1 0H12 Ground 0C03 FLASH_OE 0C08 G_ADL4 0F21 G_CFG2 0F12 Ground 0C07 FLASH_WE 0K19 G_ADL5 0G21 G_DEVSEL 0E12 Ground 0C11 G_ACK64 0G14 G_ADL6 0H21 G_FRAME 0C12 Ground 0C15 G_ADH0 0D18 G_ADL7 0J25 G_GNT0 0A13 Ground 0C19 G_ADH1 0H15 G_ADL8 0H22 G_GNT1 0E13 Ground 0C23 G_ADH2 0F17 G_ADL9 0H24 G_GNT2 0B11 Ground 0D13 G_ADH3 0J15 G_ADL10 0L16 G_GNT3 0D12 Ground 0G03 G_ADH4 0E16 G_ADL11 0G25 G_GNT4 0J11 Ground 0G07 G_ADH5 0E15 G_ADL12 0G24 G_GNT5 0F18 Ground 0G11 G_ADH6 0E18 G_ADL13 0F25 G_GNT6 0W14 Ground 0G15 G_ADH7 0J16 G_ADL14 0F24 G_GNT7 0N21 Ground 0G19 G_ADH8 0G16 G_ADL15 0D24 G_IDSEL 0U19 Ground 0H25 G_ADH9 0H16 G_ADL16 0B22 G_INTA AE13 Ground 0K21 G_ADH10 0B20 G_ADL17 0A20 G_INTB 0A10 Ground 0L03 G_ADH11 0B18 G_ADL18 0C18 G_INTC 0C13 Ground 0L07 G_ADH12 0A21 G_ADL19 0C17 G_INTD AA20 Ground 0L11 G_ADH13 0F19 G_ADL20 0F14 G_IRDY 0A12 Ground 0L14 G_ADH14 0G18 G_ADL21 0F15 G_LOCK 0G13 Ground 0L15 G_ADH15 0H17 G_ADL22 0E14 G_PAR 0H23 Ground 0L19 G_ADH16 0D21 G_ADL23 0B14 G_PAR64 0E25 Ground 0L23 G_ADH17 0E20 G_ADL24 0H13 G_PERR 0A22 Ground 0N04 G_ADH18 0K16 G_ADL25 0B15 G_REQ0 0F11 Ground 0N13 G_ADH19 0E22 G_ADL26 0D15 G_REQ1 0D11 Ground 0N22 G_ADH20 0J19 G_ADL27 0D17 G_REQ2 AC21 Ground 0R03 G_ADH21 0H19 G_ADL28 0H14 G_REQ3 0G12 Ground 0R07 G_ADH22 0F23 G_ADL29 0C20 G_REQ4 0C09 Ground 0R11 Page 18 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pins.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Signal Name Signal Pin Signal (Page 2 of 4) Pin Signal Pin Signal Pin Ground 0R14 MADDR12 0F04 MDATA37 0E03 MUX_OEA 0D09 Ground 0R15 MADDR0_ODD 0G05 MDATA38 0N09 MUX_OEB 0A09 Ground 0R19 MDATA0 0U07 MDATA39 0K05 MUX_SEL 0D08 Ground 0R23 MDATA1 0V07 MDATA40 0L05 No Connect 0A03 Ground 0T11 MDATA2 0U08 MDATA41 0H02 No Connect 0C01 Ground 0T15 MDATA3 0T07 MDATA42 0H01 No Connect 0C25 Ground 0W03 MDATA4 0V03 MDATA43 0G01 No Connect AC01 Ground 0W07 MDATA5 0R01 MDATA44 0K08 No Connect AC25 Ground 0W11 MDATA6 0W04 MDATA45 0G06 No Connect AE03 Ground 0W15 MDATA7 0M07 MDATA46 0H07 No Connect AE23 Ground 0W19 MDATA8 0U04 MDATA47 0D01 No Connect 0A23 Ground 0W23 MDATA9 0N08 MDATA48 0E01 NODLK AB03 Ground AB13 MDATA10 0N07 MDATA49 0F02 O_GPIO0 0U13 Ground AC03 MDATA11 0R02 MDATA50 0F01 O_GPIO1 0U12 Ground AC07 MDATA12 0R04 MDATA51 0K07 O_GPIO2 0Y08 Ground AC11 MDATA13 0P01 MDATA52 0G02 P_ADL0 0T24 Ground AC15 MDATA14 0P03 MDATA53 0K03 P_ADL1 0P20 Ground AC19 MDATA15 0P05 MDATA54 0J03 P_ADL2 0P22 Ground AC23 MDATA16 0T01 MDATA55 0H04 P_ADL3 0R22 Ground AD02 MDATA17 0V04 MDATA56 0J06 P_ADL4 0R20 Ground AD24 MDATA18 0U06 MDATA57 0J01 P_ADL5 0Y23 Ground AE01 MDATA19 0T09 MDATA58 0K01 P_ADL6 0P24 Ground AE25 MDATA20 0T08 MDATA59 0L09 P_ADL7 0R24 Ground 0G23 MDATA21 0Y05 MDATA60 0H05 P_ADL8 0N18 INT1 AC16 MDATA22 0R05 MDATA61 0F05 P_ADL9 0U22 INT2 0E23 MDATA23 0V02 MDATA62 0K09 P_ADL10 0N19 Locator 0A01 MDATA24 0V01 MDATA63 0J08 P_ADL11 0N25 MADDR0_EVEN 0G10 MDATA25 0T05 MDATA64 0H08 P_ADL12 0L24 MADDR1 0J10 MDATA26 0T03 MDATA65 0D02 P_ADL13 0L22 MADDR2 0E08 MDATA27 0T10 MDATA66 0D03 P_ADL14 0M24 MADDR3 0D07 MDATA28 0V05 MDATA67 0D05 P_ADL15 0M22 MADDR4 0E10 MDATA29 0R08 MDATA68 0H09 P_ADL16 0M19 MADDR5 0C10 MDATA30 0V06 MDATA69 0G08 P_ADL17 0L25 MADDR6 0B08 MDATA31 0U01 MDATA70 0F07 P_ADL18 0K25 MADDR7 0A07 MDATA32 0U03 MDATA71 0H10 P_ADL19 0L17 MADDR8 0B07 MDATA33 0R09 MUX_CLKEN1B 0A05 P_ADL20 0D20 MADDR9 0A06 MDATA34 0Y03 MUX_CLKEN2B 0A08 P_ADL21 0J20 MADDR10 0B06 MDATA35 0R06 MUX_CLKENA1 0E11 P_ADL22 0K24 MADDR11 0C04 MDATA36 0H03 MUX_CLKENA2 0D04 P_ADL23 0K23 CPC710_Pins.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 19 of 209 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Signal Name Signal Pin Signal (Page 3 of 4) Pin Signal Pin Signal Pin P_ADL24 0K18 P_SERR 0U23 SDCS4 0P09 SYS_ADDR22 0V25 P_ADL25 0M17 P_STOP 0W22 SDCS5 0N03 SYS_ADDR23 0Y21 P_ADL26 0N17 P_TRDY AA23 SDCS6 0F03 SYS_ADDR24 0W20 P_ADL27 0L18 PCG_CLK 0D14 SDCS7 0H06 SYS_ADDR25 0V19 P_ADL28 0M18 PCI_CLK 0P02 SDCS8 0M05 SYS_ADDR26 0V18 P_ADL29 0L20 PLL_LOCK 0B10 SDCS9 0M03 SYS_ADDR27 AB25 P_ADL30 0L21 PLL_RESET 0M11 SDCS10 0L02 SYS_ADDR28 AB24 P_ADL31 0N23 PLL_TUNE0 0R16 SDCS11 0J04 SYS_ADDR29 AB23 P_CBE0 0P18 PLL_TUNE1 0T16 SDCS12 0L04 SYS_ADDR30 AC24 P_CBE1 0U25 PLN_RTC_CLK AA22 SDCS13 0L06 SYS_ADDR31 0V23 P_CBE2 0T25 POWERGOOD 0T02 SDCS14 0G04 SYS_ADDRP0 AB22 P_CBE3 0R17 PRES_OE0 0B12 SDCS15 0L08 SYS_ADDRP1 0U20 P_CFG0 0M15 PRES_OE1 0C06 SDRAS0 0M09 SYS_ADDRP2 0Y20 P_CFG1 0N15 RESERVED1 0U16 SDRAS1 0M10 SYS_ADDRP3 0W17 P_CFG2 0P15 RESERVED2 0M13 SDRAS2 0N11 SYS_ARTRY AA12 P_DEVSEL 0V20 RESERVED3 0L12 SDRAS3 0P11 SYS_BG0 0Y01 P_FRAME 0Y18 RESERVED4 0R13 SYS_AACK 0W02 SYS_BG1 0Y02 P_GNT_0 0T19 RESERVED5 0L13 SYS_ADDR0 0V17 SYS_BR0 AE14 P_GNT1 0T21 RESERVED6 0P13 SYS_ADDR1 0Y19 SYS_BR1 AE12 P_GNT2 0R21 RESERVED7 AB08 SYS_ADDR2 0V16 SYS_BR2 0K15 P_GNT3 0T17 RESERVED8 0Y09 SYS_ADDR3 0W16 SYS_BR3 0K17 P_GNT4 0T18 RI 0M04 SYS_ADDR4 AE19 SYS_CLK 0K20 P_GNT5 0U18 SCAN_GATE 0D10 SYS_ADDR5 AD19 SYS_CONFIG0 0N12 P_GNT6 0K04 SDCAS0 0K10 SYS_ADDR6 AE20 SYS_CONFIG1 0N14 P_IRDY AB20 SDCAS1 0K11 SYS_ADDR7 AD20 SYS_DATA0 AA19 P_ISA_MASTER 0P25 SDCAS2 0J12 SYS_ADDR8 AE21 SYS_DATA1 AA16 P_LOCK 0R18 SDCAS3 0J13 SYS_ADDR9 0W18 SYS_DATA2 AB16 P_MEMACK 0T22 SDCKE0 0J07 SYS_ADDR10 0W21 SYS_DATA3 AC20 P_MEMREQ 0T20 SDCKE1 0E04 SYS_ADDR11 AE22 SYS_DATA4 0V14 P_PAR 0R25 SDCKE2 0F09 SYS_ADDR12 AD22 SYS_DATA5 AB17 P_PERR 0V22 SDCKE3 0C02 SYS_ADDR13 AC22 SYS_DATA6 AB15 P_REQ0 0P23 SDCKE4 0L10 SYS_ADDR14 AD23 SYS_DATA7 AD15 P_REQ1 0P21 SDCKE5 0F06 SYS_ADDR15 0Y22 SYS_DATA8 AB11 P_REQ2 0P19 SDCKE6 0E06 SYS_ADDR16 0V24 SYS_DATA9 AB10 P_REQ3 0M25 SDCKE7 0B03 SYS_ADDR17 AA25 SYS_DATA10 AA10 P_REQ4 0M23 SDCS0 0L01 SYS_ADDR18 0Y24 SYS_DATA11 AA11 P_REQ5 0M21 SDCS1 0M01 SYS_ADDR19 0Y25 SYS_DATA12 AB07 P_REQ6 0T12 SDCS2 0N01 SYS_ADDR20 0W24 SYS_DATA13 AE08 P_RST 0J23 SDCS3 0N05 SYS_ADDR21 0W25 SYS_DATA14 AE07 Page 20 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pins.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Signal Pins, Sorted by Signal Name Signal Pin Signal (Page 4 of 4) Pin Signal Pin Signal Pin SYS_DATA15 AA08 SYS_DATA55 AE16 SYS_TT3 0V08 VDD 0Y13 SYS_DATA16 0U10 SYS_DATA56 AD14 SYS_TT4 AA04 VDD AA02 SYS_DATA17 0W10 SYS_DATA57 AA13 TCK 0P06 VDD AA03 SYS_DATA18 AD06 SYS_DATA58 AA15 TDI 0P04 VDD AA05 SYS_DATA19 0Y07 SYS_DATA59 AC13 TDO 0Y12 VDD AA09 SYS_DATA20 AA07 SYS_DATA60 0V13 TESTIN 0B16 VDD AA17 SYS_DATA21 AE05 SYS_DATA61 0W13 TESTOUT 0M16 VDD AA21 SYS_DATA22 AE06 SYS_DATA62 AD12 TMS 0M20 VDD AA24 SYS_DATA23 AD07 SYS_DATA63 AD11 TRST 0P08 VDD AD01 SYS_DATA24 AD08 SYS_DATAP0 0V10 VDD 0B01 VDD AD05 SYS_DATA25 AC10 SYS_DATAP1 0W08 VDD 0B05 VDD AD09 SYS_DATA26 AD10 SYS_DATAP2 0V09 VDD 0B09 VDD AD13 SYS_DATA27 AC09 SYS_DATAP3 0W09 VDD 0B17 VDD AD17 SYS_DATA28 0U11 SYS_DATAP4 AD04 VDD 0B21 VDD AD21 SYS_DATA29 0V11 SYS_DATAP5 AD03 VDD 0B25 VDD AD25 SYS_DATA30 AE09 SYS_DATAP6 AC04 VDD 0E02 VDD AE24 SYS_DATA31 AE10 SYS_DATAP7 AB05 VDD 0E05 VDD 0A02 SYS_DATA32 AE11 SYS_DBG0 0W06 VDD 0M14 VDD 0A24 SYS_DATA33 AC08 SYS_DBG1 0W01 VDD AE02 VDD 0B13 SYS_DATA34 AC06 SYS_GBL AB21 VDD 0M12 VDD 0E09 SYS_DATA35 0Y11 SYS_HRESET0 0C05 VDD 0N02 VDD 0E17 SYS_DATA36 AB09 SYS_HRESET1 0P07 VDD 0N06 VDD 0E21 SYS_DATA37 0V12 SYS_L2_HIT AC12 VDD 0N10 VDD 0E24 SYS_DATA38 0W12 SYS_MACHK0 0Y04 VDD 0N16 VDD 0F13 SYS_DATA39 AB12 SYS_MACHK1 AE04 VDD 0N20 VDD 0J02 SYS_DATA40 AB14 SYS_SHD AC05 VDD 0N24 VDD 0J05 SYS_DATA41 0Y15 SYS_SRESET0 0Y16 VDD 0P12 VDD 0J09 SYS_DATA42 AC18 SYS_SRESET1 0Y10 VDD 0P14 VDD 0J17 SYS_DATA43 AE15 SYS_TA AC14 VDD 0P16 VDD 0J21 SYS_DATA44 AD18 SYS_TBE 0Y14 VDD 0P17 VDD 0J24 SYS_DATA45 AE18 SYS_TBST AB02 VDD 0R12 VDD 0K13 SYS_DATA46 AA18 SYS_TEA AB06 VDD 0T13 VDD 0K14 SYS_DATA47 AB19 SYS_TS AA14 VDD 0U02 VDDA 0K22 SYS_DATA48 0U15 SYS_TSIZ0 AA01 VDD 0U05 WE0 0G09 SYS_DATA49 0Y17 SYS_TSIZ1 0W05 VDD 0U09 WE1 0B04 SYS_DATA50 AE17 SYS_TSIZ2 AB01 VDD 0U14 WE2 0A04 SYS_DATA51 AC17 SYS_TT0 AA06 VDD 0U17 WE3 0E07 SYS_DATA52 AD16 SYS_TT1 AB04 VDD 0U21 XADR_LAT 0G22 SYS_DATA53 0V15 SYS_TT2 0Y06 VDD 0U24 XCVR_RD 0J22 SYS_DATA54 AB18 CPC710_Pins.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 21 of 209 IBM Dual Bridge and Memory Controller Page 22 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pins.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller I/O Signals I/O Signal Diagram S Y S _BR [0: 1] S Y S _BR [2: 3] S Y S _L 2_H IT POW E RG O O D CHK STOP S Y S _H R E S E T [0: 1] S Y S _S R E S E T [0: 1] S Y S _M A C H K [0: 1] S Y S _TBE S Y S _CO N F IG [0: 1] NOD L K D LK 2 2 1 1 1 2 2 2 1 2 1 1 IN T [1: 2] G PIO [0: 3] 2 3 G _R E Q [0: 7] 8 8 1 PCI-64 1 Int erface 3 1 1 33-66 M H z G _G N T [0: 7] P C G _CL K G _L O CK G _CF G [0: 2] G _A R B G _ID S E L P _R E Q [0: 6] P _G N T [0: 6] P _L O CK PCI_CL K P _IS A _M A S T E R P _M E M R E Q P _M E M ACK P _CF G [0: 2] 7 7 1 1 1 1 1 3 60x Int erface 1 2 64 8 2 S IO Int erface PCI-32 Int erface 33 M H z M U X _CL K E N 1B/2B/A 1/A 2 4 M U X _O E A ,M U X _O E B 2 M em ory 1 Int erface M U X _S E L 2 32 4 1 5 4 1 1 1 2 1 1 2 S Y S _BG [0: 1] S Y S _A D D R [0: 31] S Y S _A D D R P [0: 3] S Y S _T S S Y S _TT[0: 4] S Y S _TSIZ[0: 2] ,S Y S _TBS T S Y S _G BL S Y S _A A C K S Y S _A R T R Y S Y S _S H D S Y S _T A ,S Y S _TE A S Y S _D A T A [0: 63] S Y S _D A T A P [0: 7] S Y S _D BG [0: 1] F L A S H _O E /W E X A D R _L AT X C V R _R D P R E S _O E [0: 1] 64 8 2 2 1 2 1 1 2 2 4 G G G G G G G G G G G 32 4 1 1 2 1 1 2 1 P _A D L [0: 31] P _CBE [0: 3] P _P A R P _F R A M E P _IR D Y ,P _T R D Y P _S T O P P _D E V S E L P _P E R R ,P _S E R R P _R S T 72 14 M D A T A [0: 71] M A D D R 0_O D D ,M A D D R 0_E V E N M A D D R [1: 12] S D C S [0: 7] /[8: 15] /S D D Q M [0: 7] S D CK E [0: 7] W E [0: 3] S D R A S [0: 3] S D C A S [0: 3] S C A N _G A T E R I,CE 0_TE ST CE 0_IO CE _T R S T TE S T O U T 16 8 4 4 4 _A D H [0: 31] ,G _A D L [0: 31] _CBE [0: 7] _P A R ,G _P A R 64 _R E Q 64,G _A C K 64 _F R A M E _IR D Y,G _T R D Y _STO P _D E V S E L _P E R R ,G _S E R R _R S T ,G _R E S E TO U T _IN T A /B/C/D BS [0: 1] 2 S Y S _CL K CE 1_A /B CE 1_C1/C2 P L N _R T C _CL K D I[1: 2] 1 2 2 1 1 M isc. 1 2 1 1 1 4 JTAG 1 TD O 1 1 2 1 P L L _L O CK PL L 1 VD D A TD I,TCK ,TM S ,T R S T TE STIN P L L _R E S E T P L L _T U N E [0: 1] 480 S ignal s /300K G at es C P C 710_Ios.fm .01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 P age 23 of 209 IBM Dual Bridge and Memory Controller Signal Descriptions Tri-state driver/receivers interface 3.3 V internal functions with 3.3 V LVTTL off-chip buses. Some receivers interface 3.3 V internal functions with either 3.3 V LVTTL or 5.0 V TTL off-chip bidirectional buses. All drivers are 50 ohm, source-terminated. In the following table, "Pull-up" in the Type column indicates an internal pullup is built into the device driver/receiver. No additional external device is required. 60x Bus Interface Signals (Page 1 of 3) Signal Name I/O Type Description Address Bus Arbitration Signals SYS_BR0 SYS_BR1 SYS_BR2 SYS_BR3 I SYS_BG0 SYS_BG1 O Bus Grant. Indicates the master associated with this signal may, with proper qualification, assume mastership of the address bus. I/O Transfer Start. Output: Indicates device has started an address tenure and the address bus and transfer attribute signals are valid. Only “address only operations” and “snoop operation with programmable TT code” are performed. Input: Indicates a master on the 60x has started an address tenure and the address bus and transfer attribute signals are valid. For address tenures that require a data transfer, this signal also indicates a request for the data bus. I/O Pull-up Address Bus. Output: Represents the physical address of a cache operation that should be snooped by devices on the 60x bus. A[0] is the most significant address bit. Input: Represents the physical address for the current transaction (except for the XferData transaction types). Pull-up Address Parity. Output: Represents one bit of odd parity for each of the four bytes of the address bus. Odd parity means that an odd number of bits, including the parity bit, are driven high. The signal assignments correspond to the following: AP[0] - A[0:7] AP[1] - A[8:15] AP[2] - A[16:23] AP[3] - A[24:31] Input: Represents one bit of odd parity for each of the four bytes of the address bus. A checkstop is generated if bad parity is detected and bit 8 is ‘1’ in the error control register. Bus Request. Indicates the device on the 60x bus associated with this signal is 5.0V-tolerant requesting ownership of the address bus. pull-up Note: SYS_BR2 and SYS_BR3 are reserved for future use. They should be tied to up level (=1). Address Transfer Start Signals SYS_TS Address Bus Signals SYS_ADDR[0:31] SYS_ADDRP[0:3] I/O SYS_CONFIG0 SYS_CONFIG1 O Configuration. Indicate the current address tenure is a configuration cycle to the device associated with this signal. The associated device must respond (if present) to addresses in the range ‘FF20 0000’ through ‘FF20 1FFF.’ Other addresses are responded to as normal. I/O Transfer Type. Output: Indicates the type of transfer in progress. The values are programmable according to the PowerPC type and stored in the ATAS register. Input: Indicates the type of transfer in progress. Transfer Attribute Signals SYS_TT[0:4] Pull-up Page 24 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Ios.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller 60x Bus Interface Signals (Page 2 of 3) Signal Name SYS_TSIZ[0:2] I/O I/O Type Description Pull-up Transfer Size. Output signals and the TBST signal: Indicate the data transfer size of the operation. Device sets these signals to a value stored in the ATAS register for the operations it initiates. Input signals and the TBST signal: For normal memory accesses, indicate the data transfer size of the operation. For XferData instructions (eciwx and ecowx), they indicate the 4-bit Resource ID (RID) of the XferData operation (TBST || TSIZ0-TSIZ2). SYS_TBST I/O Pull-up Transfer Burst. Output signal and the TSIZ signals: Indicate the data transfer size of the operation. Device sets this signal according to the bit in the ATAS register for operations it initiates. Input signal: For normal memory accesses, indicates a burst transfer is in progress. For XferData instructions (eciwx and ecowx), the input signal and the TSIZ signals indicate the 4-bit Resource ID (RID) of the XferData operation (TBST || TSIZ0-TSIZ2). SYS_GBL O Tri-state pull-up Global. Always asserted by device for transactions, it initiates to indicate all devices on the 60x bus must snoop the transaction. Address Transfer Termination Signals O Address Acknowledge. Indicates the address tenure is complete and the ARTRY sampling window ends on the following bus cycle. Address bus and transfer attribute signals must go to tri-state on the next bus cycle. SYS_ARTRY I/O Address Retry. Output indicates device detects a condition that requires an address tenure to be retried. Input: When asserted in response to a device cache operation, device assumes the cache line is modified and/or present in a CPU or L2 cache. Device then retries the operation on the PCI bus and address tenure is not rerun until the device on the PCI bus reruns its transfer. The pre-charge logic is always signaled to initiate the pre-charge sequence. SYS_SHD I/O SYS_AACK SYS_L2_HIT I Pull-up Shared. Output: Not applicable; Device only pre-charges the signal. Input: Instructs the pre-charge logic to initiate a pre-charge sequence. Pull-up L2 Hit: Indicates an external slave has been addressed by the current master. The device arbiter uses this signal to confirm positive selection of an address tenure on the 60x bus. Warning: This signal is subject to timing constraints. Data Bus Arbitration Signals SYS_DBG0 SYS_DBG1 O Data Bus Grant. Indicates the device associated with this signal may, with the proper qualification, assume mastership of the data bus. I/O Data Bus. Byte 0: Byte 1: Byte 2: Byte 3: Byte 4: Byte 5: Byte 6: Byte 7: Data Transfer Signals SYS_DATA[0:63] Pull-up CPC710_Ios.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 D[0:7] - DH[0:7] D[8:15] - DH[8:15] D[16:23] - DH[16:23] D[24:31] - DH[24:31] D[32:39] - DL[0:7] D[40:47] - DL[8:15] D[48:55] - DL[16:23] D[56:63] - DL[24:31] Page 25 of 209 IBM Dual Bridge and Memory Controller 60x Bus Interface Signals (Page 3 of 3) Signal Name SYS_DATAP[0:7] I/O Type Description Data Parity Bus. Represents one bit of odd parity for each of the eight bytes of the data bus. Odd parity means that an odd number of bits, including the parity bit, are driven high. The signal assignments correspond to the following: DP[0]: D[0:7] DP[4]: D[32:39] DP[1]: D[8:15]) DP[5]: D[40:47] DP[2]: D[16:23] DP[6]: D[48:55 DP[3]: D[24:31] DP[7]: D[56:63] I/O Data Transfer Termination Signals SYS_TA SYS_TEA I/O I/O Pull-up Transfer Acknowledge. Output: Indicates a single beat of data transfer between device and a master on the 60x bus. For read transfers, indicates the data bus is valid with read data and the master must latch it in. For writes, indicates device has latched in write data from the data bus. Device asserts the signal for each beat in a burst transfer. Input: Indicates a single beat of data transfer has occurred. The device arbiter uses this signal and the address transfer attribute signals to determine the end of the data bus tenure. Pull-up Transfer Error Acknowledge. Output: Indicates device has detected an error condition and that a machine check exception is desired. Assertion of this signal terminates the current data bus tenure. Device can be set up to transform any SYS_TEA to normal SYS_TA with machine check condition signaling on SYS_MACHK0 or SYS_MACHK1. Input: Informs the device’s 60x bus arbiter that the current data bus tenure has been terminated. Miscellaneous Signals SYS_MACHK0 SYS_MACHK1 O CHKSTOP O SYS_HRESET0 SYS_HRESET1 O Hard Reset [0:1]. Indicates the device or card associated with this signal must initiate a complete hard reset. All outputs should be released to tri-state. Duration of reset, except for device hardware system reset, is controlled by software. SYS_SRESET0 SYS_SRESET1 O Soft Reset [0:1]. Indicates the processor connected to this signal will take a reset exception. Occurs following a write to the CPU soft reset register (SRST) that has the appropriate bit set. SYS_TBE O Timebase Enable. Indicates the processor time bases should continue counting. Reflects bit 12 of the UCTL[12] register ’x FF00 1000’. POWERGOOD I Machine Check. Indicates the device has detected an error condition and a machine check exception is desired. Open Drain Pull-up Checkstop. Indicates the device has detected a non-recoverable error condition and has entered checkstop state. System Normal operation when up =1 General System Reset when down=0 INT1 O Interrupt. Interrupt generated after writing a ’1’ in the IT_ADD_SET interrupt register. This interrupt can be used by an external interrupt controller. The writing can be made from the CPU in configuration mode or from the PCI-64 bus. Only the PowerPC CPU can reset the interrupt by writing a ‘1’ in the IT_ADD_RESET interrupt reset register. INT2 O Interrupt. Indicates the end of the DMA data transfer. Corresponds to assertion of bit 4 in the GSCR status register. GPIO0 GPIO1 I/O I/O. General purpose I/O signals. DLK O Deadlock. Asserted when processor range of address is out of the non-deadlock zone. An address SYS_ARTRY is sent to the PowerPC when DLK is set. I Deadlock Disable. Used only when the deadlock address range checking is programmed. Asserted (=0), it disables checking Tie to high level (=1) the deadlock checking can be performed. NODLK Page 26 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Ios.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Memory Interface Signals Signal Name I/O Type Description MDATA[0:63] I/O Memory Data MDATA[64:71] I/O Memory Data ECC bits MADDR0_ODD O Memory Address bit 0 for Odd DIMMs MADDR0_EVEN O Memory Address bit 0 for Even DIMMs MADDR[1:12] O Memory Address bits 1 to 12 SDCS[0:7] or SDCS[8:15], SDDQM[0:7] O Programmable I/Os by setting bit 11 of the MCCR register: 0: SDRAM: Chip Select 0 to 15 1: SDRAM: Chip Select 0 to 7 and Data Mask 0 to 7 SDCKE[0: 7] O SDRAM Clock Enable WE[0:3] O Memory Write Enable: (for SDRAM only: four signals with same shape for buffering issues) SDRAS[0: 3] O SDRAM RAS: Row Address Strobe (four signals with same shape for buffering issues) SDCAS[0: 3] O SDRAM CAS: Column Address Strobe (four signals with same shape for buffering issues) BS[0:1] O SDRAM BS: Internal Bank Select Signals to be used with Texas Instruments ALVCH162268 MUX: 12 to 24-bit registered bus exchanger (For more information see http://www.ti.com/sc/) MUX_OEA MUX_OEB O Output Enable of Data to Device - Port A of the external MUX Output Enable of Data to Memory - Port B MUX_CLKEN1B MUX_CLKEN2B O Clock Enable of Data sent to the Memory MUX_CLKENA1 MUX_CLKENA2 O Clock Enable of Data sent to Device. Clock A1 the first part of the data is stored in the external MUX controller, and on clock A2 full transfer is made. MUX_SEL O Control the MUX circuit of the external MUX controller CPC710_Ios.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 27 of 209 IBM Dual Bridge and Memory Controller PCI-32 Bus Interface Signals Signal Name I/O Type Description P_ADL[0:31] I/O 32-bit Multiplexed Address/Data: A write operation is defined as the transfer of data from the PCI bus master to a PCI slave device on the PCI Bus. P_CBE[0:3] I/O Bus Command/Byte Enable P_DEVSEL I/O Device Select P_FRAME I/O Cycle Frame: Driven by the current master to indicate the beginning and duration of an access. P_IRDY I/O Initiator Ready Pull-up ISA Master on the PCI-32 bus: Indicates that the CPC710 must automatically P_DEVSEL the current Memory transfer and must not translate the PCI address before sending the address to memory. Warning: To become inactive this signal have to be connected to GND = 0 P_ISA_MASTER I P_LOCK I Lock: Used to establish, maintain, and release resource locks on PCI-64. P_MEMACK O Memory Acknowledge: Indicates device has flushed all CPU to PCI-32 bus buffers and any CPU access to PCI stops are being SYS_ARTRYed. P_MEMREQ I Pull-up Memory Request: Indicates a PCI device accessing system memory has a potential deadlock and requests device flush all posted CPU to PCI buffers and ARTRY all PCI32 bus transfers from the 60x bus. P_PAR I/O Parity Bit P_GNT[0:6] O PCI-32 Bus Grants P_REQ[0:6] I P_RST O PCI-32 Bus P_PERR I/O PCI-32 Data Parity Error P_SERR I/O PCI-32 System Parity Error: Reports parity errors on address, special cycle data, or systems. P_STOP I/O Stop: Asserted by the target to request the master to stop current transaction. P_TRDY I/O Target Ready: Asserted by the target when ready to receive data. P_CFG[0:2] O Configuration Bit Reflect: Reflects PCI-32 configuration bits 13-11 in the CONFIG ADDR register. Set to zero when bits 14 or 15 are on. Pull-up PCI-32 Bus Requests Page 28 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Ios.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI-64 Bus Interface Signals Signal Name I/O Type Description G_ADH[0:31] I/O 32-bit Multiplexed Address/Data Higher Part: In the address phase when G_REQ64 is asserted, these bits are the upper part of 64 bit address AD[63:32]. During data phase an additional 32-bits of data are transferred when G_REQ64 and G_ACK64 are both asserted. G_ADL[0:31] I/O 32-bit Multiplexed Address/Data Lower Part: A write operation is defined as the transfer of data from the PCI bus master to a PCI slave device on the PCI Bus. G_ACK64 I/O Acknowledge 64-Bit Transfer G_REQ64 I/O Request 64-Bit Transfer G_PAR64 I/O Parity Upper Double Word G_CBE[0:7] I/O Bus Command/Byte Enable G_DEVSEL I/O Device Select G_IDSEL I Pull-up Initialization Device Select: Used as chip select during configuration. G_FRAME I/O Cycle Frame G_IRDY I/O Initiator Ready G_LOCK I Lock: Used to establish, maintain and release resource locks on PCI-64. G_PAR I/O Parity Bit G_CFG[0:2] O PCI-64 Configuration: Reflects PCI-64 Configuration bits 13-11 in the CONFIG ADDR register. Set to Zero when bit 15 or 14 are on. G_GNT[0:7] O PCI-64 Bus Grant G_REQ[0:7] I Pull-up PCI-64 Bus Requests: G_REQ[2] is sampled at Reset, to select arbitration on the PCI64 bus. The arbitration can be made by the device (G_REQ[2]=1) or by external circuit (=0). In case of external arbitration, the request is send to PCI from G_GNT[1] and the grant from the external arbiter is received on pin G_REQ[1]. G_RST O I/O G_PERR I/O PCI-64 Data Parity Error G_SERR I/O PCI-64 System Parity Error: Reports parity errors on address, special cycle data, or system errors. G_STOP I/O Stop: Asserted by the target to request the master to stop the current transaction. G_TRDY I/O Target Ready: Asserted by the target when ready to receive data. G_INTA I PCI-64 Interrupt A G_INTB I PCI-64 Interrupt B G_INTC I PCI-64 Interrupt C G_INTD I PCI-64 Interrupt D G_ARB O PCI-64 Arbiter: Asserted (=1) when the device is the PCI-64 arbiter G_RESETOUT O Local Reset: Asserted by PCI-64 reset and special conditions Reset PCI-64 Bus: External pull-up required. CPC710_Ios.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 29 of 209 IBM Dual Bridge and Memory Controller Test and Clock Signals Signal Name I/O Internal Type Description SYS_CLK I System Reference Clock PCI_CLK I Main Clock Input for the PCI-32 bit bridge: 33 MHzReserved PCG_CLK I Main Clock Input for the PCI-64 bit bridge: 66 MHz PLL_LOCK O Output indicating a locked state for the PLL PLL_TUNE0 I Pull-down Loop stability tuning control of the PLL PLL_TUNE1 I Pull-up Loop stability tuning control of the PLL PLL_RESET I Pull-up Reset and Bypass mode enable of the PLL Time base enable for refresh DRAM cycles. A 7.8125 MHz Clock (128ns period) on input pin PLN_RTC_CLOCK is necessary for the DRAM refresh cycles and other internal timers such as soft reset time, software power on reset time, bus timeout and SDRAM initialization phase time. PLN_RTC_CLOCK I CE1_A I Pull-up Reserved CE1_B I Pull-up Reserved CE1_C1 I Pull-up Reserved CE1_C2 I Pull-up Reserved DI1 I Pull-up Reserved DI2 I Pull-up Reserved CE0_IO I Pull-down Reserved CE0_TEST I Pull-down Reserved RI I SCAN_GATE I Pull-down TCK I Pull-up JTAG Clock TDI I Pull-up JTAG Data Input TDO O Pull-up Reserved TMS I Pull-up Reserved TRST I Pull-up Asynchronous JTAG Reset TESTIN I Pull-up Reserved. Must be set to 0. CE_TRST I Pull-up JTAG Compliance Enable: Down level (=0): Isolate the JTAG from the system reset signal POWERGOOD. Up level (=1): the POWERGOOD going to 0, Resets the JTAG. TESTOUT O Reserved VDDA I Analog VDD for the PLL. Filtering on this 3.3V power supply is necessary to avoid problems with the on-chip PLL. Reserved. Must be set to 1. Reserved Page 30 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Ios.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller SIO Signals Signal Name I/O Type Description FLASH_OE O Output Enable: FLASH ROM. FLASH_WE O Write Enable: FLASH ROM. PRES_OE0 O Output Enable: Presence detect (PD) buffer 0. PRES_OE1 O Output Enable: Presence detect (PD) buffer 1. XADR_LAT O Latch Signal: For SIO address register. XCVR_RD O Address Direction: SIO address bus. Reserved Signals Signal Name I/O Type Description RESERVED1 I External Pull-Up recommended. RESERVED2 O External Pull-Up recommended. RESERVED3 O External Pull-Up recommended. RESERVED4 I Pull-Up External Pull-Up recommended. RESERVED5 I Pull-Up External Pull-Up recommended. RESERVED6 O RESERVED7 I RESERVED8 O External Pull-Up recommended. Pull-Up CPC710_Ios.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 External Pull-Up recommended. External Pull-up recommended Page 31 of 209 IBM Dual Bridge and Memory Controller Page 32 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Ios.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Registers CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 33 of 209 IBM Dual Bridge and Memory Controller Registers The registers for the device are specified in three regions. Except for the Standard PCI Configuration Space, which uses indirect addressing, all the registers can be defined in the upper 16 MB of the 4 GB address range. Standard PCI Configuration Space ( register x‘00’ to x‘68’ ) There are two sets of PCI Configuration Space registers; one for each PCI bridge. These registers are accessed by a R/W of the CFGD with the address of the target register of the corresponding PCI bus in the CFGA (Configuration Address register) which specifies the register number and operation to perform. The table Standard PCI Configuration Register List on page 37 describes the Specific PCI Host Bridge Registers supported by the device. The two registers PSBAR and PPBAR can be accessed and configured by the CPU or the PCI-64 bus through configuration cycles. Each of these registers is described in detail on pages 37 through 62. Specific PCI Host Bridges Space (BAR + x‘000F 6110’ to BAR +x‘000F 9810’) There are two almost identical sets of registers, one for each PCI bridge that can be placed by the user in the upper 16MB of the System Memory. One BAR value (Base Address) has to be defined first for each PCI bridge; for example as shown in the following figure, BAR_PCI32=FF50 0000 and BAR_PCI64=FF40 0000. The register space for the PCI-32 or PCI-64 bridge can then be accessed by the CPU with the PCI corresponding base value loaded in the Base Address Register (BAR x‘FF20 0018’). The differenciation between the PCI-64 or PCI-32 is made by enabling the corresponding bit in the Connectivity Configuration Register (CNFR x‘FF00 000C’). The table Specific PCI Host Bridge Register List on page 63 describes the supported Registers. Each of these registers is described in detail on pages 63 through 92. System Space Address Map (x‘FF00 0000’ to x‘FFFF FFFF’) The upper 16 MB of the 4 GB address range is reserved for system support functions. The table Standard System Registers List on page 93 describes the System Space Registers supported. These registers are defined as Big Endian unless otherwise noted. If the processor is operating in Little Endian mode, software must issue Load & Store reverse instructions to access these registers. The device responds to all addresses listed in the table Standard System Registers List on page 93 with a minimum granularity of 4 K blocks. Accesses to these registers must be single word accesses on word boundaries or unpredictable results may occur. Each of these registers is described in detail on pages 93 through 129. Shaded address ranges indicate areas where IBM Dual Bridge and Memory Controller will respond with TEA (addressing error is detected and logged in the System Error Status Register (SESR x’FF00 1060 bit 15 or bit 22)). Page 34 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Register Map x’FFFF FFFF’ System Space Address Map BOOT ROM (2 MB) Boot ROOM Space SIO Address Space 2 BAR + x’000F 9810’ PCI-32 PHB BAR + x’000F 6110’ BAR = FF50 0000 for example when CNFR[30-31]=10 BAR + x’000F 9810’ PCI-64 PHB BAR + x’000F 6110’ BAR = FF40 0000 for example when CNFR[30-31]=11 SIOA2 (Reserved) Specific PCI 32 Host Bridge Space PSEA CRR SMBAR CFGD SIBAR PSSIZE PCIDG PR ACR CTLRW INTA PIBAR MSIZE CTLRO BARPS PMBAR IOSIZE CFGA PSBAR TIODLK PPBAR CSR BPMDLK PLSSR TPMDLK BIODLK Specific PCI-64 Host Bridge Space SMBAR CFGD PSEA CRR SIBAR PSSIZE PCIDG PR CTLRW ACR INTA PIBAR MSIZE CTLRO BARPS PMBAR IOSIZE CFGA BPMDLK INT_SET TPMDLK CSR BIODLK PLSSR TIODLK IT_AD_RESET Upper 16 MB x’FF20 1000’ Device Specific Config Space PCIENB Standard System Config Space DCR DID BAR DMA Transfer Space GSCR XSSR XTAR GSSR XPAR GSCR XSCR XWAR GSSR SIO Address Space 1 XSCR XSSR XPAR XWAR XTAR SIOA1 (Reserved) Specific System Space UCTL ERRC RGBAN2 AVDG MPSR SESR GPDIR MCCR SIOC SEAR GPIN MESR 60XC PGCHP GPOUT MEAR MCER0 SRST RGBAN1ATAS MCER1 MCER2 MCER3 MCER4 MCER5 MCER6 MCER7 SIOR0 SIOR1 Standard System Space PIDR CNFR RSTR SPOR x’FF00 0000’ 4 GB -16 MB x’0000 0000’ 0 31 Standard PCI Configuration Space PCI-64 Register x’128’ PCI-32 Register x’68’ Register x’00’ 31 0 Register number is specified in the CFGA (Configuration Address) SPI HDRT MINGNT RETRY VID DEVID SUBC PSBAR MAXLT DLKRETRY BUSNO PSEM CMND CLASS CSIZE INTLN SUBNO IT_ADD_SET STAT LTIM INTPIN DISCNT RID ESET Note: BOXED registers are key registers that define PCI bus configuration and register settings. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 35 of 209 IBM Dual Bridge and Memory Controller Standard PCI Configuration Registers The following registers are defined as Little Endian (LE) ordering. Therefore, for software running in Big Endian (BE) mode, any access to these registers (that is not a single byte access) must utilize the load/store byte reversal instructions when accessing these registers. Software running in LE mode can use the normal load and store instructions. There is one set of registers for the PCI 32 bit and one set for the PCI-64 bit. The relative address (or register number) of these registers is specified in the CFGA (Configuration Address). PCI Configuration Space 31 16 15 0 Device ID Vendor ID Status Command Subclass Code Header Type Base Code BIST Prg Intf Latency Timer Rev ID Cache Line Size 00 04 08 0C 10 PSBAR (for PCI-64 only) 14 Reserved for Base Address Registers 24 28 Reserved 2C Reserved for Expansion ROM Base Addr 30 34 Reserved 38 Maximum Latency Reserved Minimum Grant Disconnect Counter Interrupt Pin Subordinate Bus Numb Interrupt Line Bridge Bus Numb 3C 40 44 48 Reserved 4C Reserved Dead Lock Retry Retry Counter 50 54 Reserved 58 5C PSEM -Semaphores (for PCI-64 only) 60 IT_ADD_SET (for PCI-64 only) 64 INT_RESET (for PCI-64 only) 68 6C Reserved FC Page 36 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Standard PCI Configuration Register List 1. 2. 3. 4. Relative Address Name 00 to 01 VID 02 to 03 Use Page Notes Vendor ID Register 38 1 DEVID PCI Device ID Register 38 1 04 to 05 CMND Command Register 39 06 to 07 STAT Status Register 41 2 08 RID Revision ID 43 1 09 SPI Standard Programming Interface 43 1 00A SUBC Sub-class Code 44 1 0B CLASS Base Class Code 45 1 0C CSIZE Cache Line Size 46 1 0D LTIM Latency Timer 47 0E HDRT Header Type 48 0F BIST Built In Self Test 49 10 PSBAR System Base Address Register for PCI-64 50 3C INTLN Interrupt Line 51 3D INTPIN Interrupt Pin 52 3E MINGNT Minimum Grant 53 1 3F MAXLT Maximum Latency 54 1 40 BUSNO Bus Number 55 41 SUBNO Subordinate Bus Number 56 42 DISCNT Disconnect Counter 57 50 RETRY Retry Counter 58 51 DLKRETRY Auto Retry Counter for access in Peripheral space with potential deadlock 59 3 60 PSEM PCI-64 Semaphore Register 60 4 64 IT_ADD_SET Set PCI-64 Inter-Processor (INT1) Interrupt. 61 4 68 INT_RESET Reset of INTA,INTB,INTC,INTD on the PCI-64 62 4 1 4 Read-Only Register, write is ignored Writes will only reset bits in this register; write data interpreted as 1 = reset, 0 = ignore Only for PCI-32 Only for PCI-64 CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 37 of 209 IBM Dual Bridge and Memory Controller Vendor ID (VID) This register identifies the device manufacturer. Reset Value x’1014’ Address x‘00’ Access Type Read Only VID 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit(s) 15 - 0 Description Vendor Identification Number Value = x’1014’; (x’14’ for address 00 and x’10’ for address 01) Device ID (DEVID) This register identifies a particular device. Reset Value PCI-32 PCI-64 x’0105’ x’00FC’ Address x‘02’ Access Type Read Only DEVID 15 14 13 12 11 10 9 8 7 6 5 4 3 Bit(s) 15 - 0 2 1 0 Description Device Identification Number Value: x’0105’ for PCI-32 (x’05’ for address 02 and x’01’ for address 03) Value: x’00FC’ for PCI-64 (x’FC’ for address 02 and x’00’ for address 03) Page 38 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Command (CMND) This register provides control over the bridge’s PCI behavior. Reserved Enable I/O Space (Slave) Read/Write Enable Memory Space (Slave) Access Type Bus Master Enable x‘04’ Special Cycle Enable Address Memory Write & Invalidate Command Enable x’0156’ x’0356’ VGA Palette Snoop PCI-32 PCI-64 PCI Bus Parity Enable programming example Add Wait States x’0000’ x’0000’ G_SERR Enable PCI-32 PCI-64 Fast Back-to-back Enable Reset Value 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit(s) 15 - 10 Description Reserved 9 Fast Back-to-back Enable 0: Disabled 1: PCI Bridge issues fast back-to-back transfers without regard to which target is being addressed, providing that the previous transaction was a write. Note: This bit should be set if all slaves on the PCI bus support this capability. 8 SERR Enable 0: PCI Bridge will not assert G_SERR upon detecting an error. 1: PCI bridge will assert G_SERR for PCI address parity error 7 Add Wait States. Read Only. Always returns 0. Device does not support address data stepping. 6 PCI Bus Parity Enable 0: Device will disable all parity checking on the PCI bus 1: Device will detect and report parity errors on the PCI bus 5 VGA Palette Snoop. Read Only. Always returns 0. Device is not VGA compatible. 4 Memory Write & Invalidate Command Enable 0: Device does not generate this type of cycle. 32-byte transfers use the Memory Write command. 1: Device generates this cycle as a master for any 32-byte transfer. 3 Special Cycle Enable. Read Only. Always returns 0. Device will not respond to Special Cycle commands. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 39 of 209 IBM Dual Bridge and Memory Controller Bit(s) Description 2 Bus Master Enable 0: PCI Bridge master capability is disabled. 1:PCI Bridge performs as a PCI master for accesses to its address spaces. 1 Enable Memory Space (Slave) 0: PCI Bridge will not respond to memory accesses on the PCI bus 1: PCI Bridge will respond to memory accesses on the PCI bus 0 Enable I/O Space (Slave) 0: PCI Bridge will not respond to IO accesses on the PCI bus 1: PCI Bridge will respond to IO accesses on the PCI bus Page 40 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Status (STAT) This register records status and error information from PCI bus transfers. Reads from this register behave normally. Writes to this register are restricted, in that software cannot set any bit in this register, only reset. Additionally, to reset a bit, software must write a 1 to the corresponding bit location. For example, to reset only bit 14, software must write ‘0100 0000 0000 0000’b to this register. 9 Target Fast Back-to-back Capable 15 14 13 12 11 10 Data Parity Detected DevSel Timing Read/Write Signaled Target Abort (Slave) Access Type Received Target Abort (Master) x‘06’ Signalled Master Abort Address G_SERR x’0280’ Parity Error Reset Value 8 7 Reserved 6 5 4 3 2 1 Bit(s) 0 Description 15 Parity Error 0: No Error 1: PCI Bridge has detected a parity error; bit set even if parity checking is disabled. 14 Signaled System Error (G_SERR) 0: No Error 1: PCI Bridge has asserted SERR due to an address parity error. 13 Signaled Master Abort 0: No Error 1: PCI Bridge has issued a master abort. 12 Received Target Abort (Master) 0: No Error 1: PCI Bridge has detected a target abort for one of its transactions. 11 Signaled Target Abort (Slave) 0: No Error 1: PCI Bridge as a slave has issued a target abort. 10 - 9 8 DevSel Timing. Read Only 01: PCI Bridge responds with Medium timing on G/P_DEVSEL signal. Data Parity Detected 0: No Error 1: This bit is set if the following 3 conditions are met: I) PCI Bridge asserted, or observed G_PERR signal on PCI bus II) PCI Bridge acting as master III) Bit 6 of Command Register set CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 41 of 209 IBM Dual Bridge and Memory Controller Bit(s) Description 7 Target Fast Back-to-back Capable. Read Only. Always returns a 1 to indicate that the PCI Bridge as a target will accept fast back-to-back transfers when the transfers are not to the same device. 6-0 Reserved Page 42 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Revision ID (RID) Reset Value x’00’ Address x‘08’ Access Type Read Only Revision ID 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Provides an extension to the PCI Device ID register. Device always responds with x’00’ for reads from this register. Programming Interface (SPI) Reset Value x’00’ Address x‘09’ Access Type Read Only Programming Interface 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Defines a specific register-level programming interface. Device always responds with x’00’ for reads from this register. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 43 of 209 IBM Dual Bridge and Memory Controller Sub-Class Code (SUBC) Reset Value x’00’ Address x‘0A’ Access Type Read Only Sub-Class Code 7 6 5 4 3 2 1 0 Bit(s) Description 0 - 15 Specifically identifies a particular function of the Base Class Code register. Device always responds with x’00’ for reads to indicate a HOST type of bridge device. Page 44 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Base Class Code (CLASS) Reset Value x’06’ Address x‘0B’ Access Type Read Only Base Class Code 7 6 5 4 3 2 1 0 Bit(s) 7-0 Description Classifies the type of function this device performs. Device always responds with x’06’ for reads to indicate a Bridge device. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 45 of 209 IBM Dual Bridge and Memory Controller Cache Line Size (CSIZE) Reset Value x’08’ Address x‘0C’ Access Type Read Only Cache Line Size 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Specifies the cache line size in units of 32-bit words. Device always responds with x’08’ for reads to indicate that device will always disconnect from any PCI master burst operation that crosses a 32-byte boundary. Page 46 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Latency Timer (LTIM) Reset Value x’00’ Address x‘0D’ Access Type Read/Write Latency Timer 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Provides bus masters with a minimum guaranteed time slice on the PCI bus. The value programmed into this register is the minimum number of PCI bus clocks that a master can own the PCI bus starting from the cycle that FRAME is activated. This register is set to X’00’ at reset. The recommended value to program into this register is x’08’. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 47 of 209 IBM Dual Bridge and Memory Controller Header Type (HDRT) Reset Value x’00’ Address x‘0E’ Access Type Read Only Header Type 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Specifies the layout of bytes x’10’ through x’3F’ in the configuration header and whether or not a particular device contains multiple functions. Device always responds with x’00’ to reads to indicate Layout 0. Writes to this register are ignored. Page 48 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Built in Self Test (BIST) Reset Value x’00’ Address x‘0F’ Access Type Read Only BIST 7 6 5 4 3 2 1 0 Bit(s) 7-0 Description Provides status and control for a Built-in Self Test which device does not support. Device responds with x’00’ to reads from this register and ignores writes. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 49 of 209 IBM Dual Bridge and Memory Controller System Base Address Register for PCI-64 (PSBAR) For PCI-64 only, the definition is the same as that for System Base Address Register for PCI-32 (PSBAR) on page 84. Reset Value x’0000 0000’ Address x‘10’ Access Type Read/Write PSBAR 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 Bit(s) 31 - 0 9 8 7 6 5 4 3 2 1 0 Description System Base Address for PCI-64. Contains the upper bits of the System Base address that memory is mapped to. Page 50 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Interrupt Line (INTLN) Reset Value x’00’ Address x‘3C’ Access Type Read Only Interrupt Line 7 6 5 4 3 2 1 0 Bit(s) 7-0 Description Indicates interrupt routing information for devices that implement an interrupt. The PCI bridge logic does not generate interrupts and therefore this register is not implemented. Device responds with x’00’ to reads from this register and ignores Writes. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 51 of 209 IBM Dual Bridge and Memory Controller Interrupt Pin (INTPIN) Reset Value x’00’ Address x‘3D’ Access Type Read Only Interrupt Pin 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Specifies which particular interrupt pin, INTA, INTB, INTC, or INTD, is used to generate interrupts. Since the PCI bridge does not generate any interrupts, Device responds with x’00’ to reads from this register and ignores writes. Page 52 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Minimum Grant (MINGNT) Reset Value x’00’ Address x‘3E’ Access Type Read Only Minimum Grant 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Specifies the length of a device’s burst period in 0.25 µsecs. Device has no specific requirements and therefore always responds with x’00’. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 53 of 209 IBM Dual Bridge and Memory Controller Maximum Latency (MAXLT) Reset Value x’00’ Address x‘3F’ Access Type Read Only Maximum Latency 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Specifies how often the device needs to gain access to the PCI bus in 0.25 µs. Device has no specific requirements and therefore always responds with x’00’. Page 54 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bus Number (BUSNO) Reset Value x’00’ Address x‘40’ Access Type Read/Write Bus Number 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Contains the assigned bus number for this bridge. Device uses this number to determine what action to take for configuration cycles directed to this bridge. After reset, this register contains a value of x’00’. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 55 of 209 IBM Dual Bridge and Memory Controller Subordinate Bus Number (SUBNO) Reset Value x’00’ Address x‘41’ Access Type Read/Write Subordinate Bus Number 7 6 5 4 3 2 1 0 Bit(s) 7-0 Description Specifies the largest bus number beneath this bridge. After reset, this register contains a value of x’00’. Page 56 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Disconnect Counter (DISCNT) Reset Value x’00’ Address x‘42’ Access Type Read/Write Disconnect Counter 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Device uses this register when acting as a target device as a time-out mechanism in burst operations. The value written to this register is multiplied by four and used to determine when the bridge should assert STOP#. After reset, this register contains x’00’ which disables the timer. This counter is enabled only if bit 0 (for PCI 32) or bit 8 (for PCI-64) of AVDG Register is set (see Diagnostic Register (AVDG) on page 119) CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 57 of 209 IBM Dual Bridge and Memory Controller Retry Counter (RETRY) Reset Value x’00’ Address x‘50’ Access Type Read/Write RETRY 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 When the device is a Master on the PCI bus, this register is used as a time-out mechanism for continuous retries on the PCI bus. Whenever a retry occurs for a particular address, the PCI bridge logic increments (decrements) a counter. The 8-bit counter is reset whenever data is transferred. If the count reaches the value specified in this register, the PCI bridge logic will not retry the access and will report the error. After reset, the register contains x’00’ which disables the retry counter. Page 58 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Deadlock Retry Counter (DLKRETRY) Reset Value x’00’ Address x‘51’ Access Type Read/Write DLKRETRY 7 6 5 4 3 2 1 0 Bit(s) Description 7-0 Available only for the PCI-32, this 8-bit counter is used to limit the number of Retries in the case of an access in a deadlock area space defined with the BPMDLK/TPMDLK or BIODLK/TIODLK registers. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 59 of 209 IBM Dual Bridge and Memory Controller Semaphore (PSEM) x‘60’ Access Type Read/Write Data Memorized Data Memorized Data Memorized 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 Bit(s) 31 24 - 30 23 16 - 22 15 8 - 14 7 0-6 Sem0_ctrl Address Sem2_ctrl x’0000 0000’ Sem3_ctrl Reset Value Sem1_ctrl This register is used by the PowerPC CPU or the PCI-64. 9 8 7 Data Memorized 6 5 4 3 2 1 0 Description Sem3_ctrl This bit controls the write of byte 0: Write is possible 1: Write is made if data = 0 Data Memorized Sem2_ctrl This bit controls the write of byte 0: Write is possible 1: Write is made if data = 0 Data Memorized Sem1_ctrl This bit controls the write of byte 0: Write is possible 1: Write is made if data = 0 Data Memorized Sem0_ctrl This bit controls the write of byte 0: Write is possible 1: Write is made if data = 0 Data Memorized Page 60 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Set Addressed Interrupt (IT_ADD_SET) This is a Virtual Register. When addressed, the interrupt signal INT1 is set (goes to O). The SET can be done from the PCI-64 or from the PowerPC CPU in configuration mode. Reset Value x’0000 0000’ Address x‘64’ Access Type Write Only Reserved Set_add_it 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 Bit(s) 9 8 7 6 5 4 3 2 1 0 Description 31 - 8 Reserved 7-0 Set_add_it 1: Writing a 1 in one of these 8 bits Resets the interrupt signal INT1 0: No action CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 61 of 209 IBM Dual Bridge and Memory Controller Reset PCI-64 Interrupt (INT_RESET) Resets one of the posted interrupt G_INTA, G_INTB, G_INTC, G_INTD on the PCI-64bit bus. Reset can be done from the PCI-64 or from the CPU in configuration mode. The CPU can only execute the SET of INTA, INTB, INTC, INTD when writing in Register INT_SET at address BAR + x’000F 8310’. Reset Value x’0000 0000’ Address x‘68’ Access Type Read/Write Reserved Set_add_it 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 Bit(s) 9 8 7 6 5 4 3 2 1 0 Description 31 - 4 Reserved 3-0 RESET_Interrupts 1: Resets the bit corresponding to one PCI-64 interrupt 0: No action Bit 0: G_INTA Bit 1: G_INTB Bit 2: G_INTC Bit 3: G_INTD Page 62 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Specific PCI Host Bridge Registers Specific PCI Host Bridge Register List Real Address Name Use Page Note BAR + x’000F 6110 PSEA PCI Slave Error Address 64 1 BAR + x’000F 6120’ PCIDG PCI Diagnostic Register 65 BAR + x’000F 7700’ INTACK Interrupt Acknowledge Cycle 66 BAR + x’000F 7800’ PIBAR PCI Base Address for I/O 67 BAR + x’000F 7810’ PMBAR PCI Base Address for Memory 68 BAR + x’000F 7EF0’ CRR Component Reset Register 69 BAR + x’000F 7F20’ PR Personalization Register 70 BAR + x’000F 7F30’ ACR Arbiter Control Register 72 BAR + x’000F 7F40’ MSIZE PCI Memory Address Space Size 73 1 BAR + x’000F 7F60’ IOSIZE PCI I/O Address Space Size 74 BAR + x’000F 7F80’ SMBAR System Base Address for PCI Memory 75 BAR + x’000F 7FC0’ SIBAR System Base Address for PCI I/O 76 BAR + x’000F 7FD0’ CTLRW Configuration Register R/W 77 BAR + x’000F 7FE0’ CTLRO Configuration Register R/O 78 1 BAR + x’000F 8000’ CFGA CONFIG_ADDR 79 2 BAR + x’000F 8010’ CFGD CONFIG_DATA 80 2 BAR + x’000F 8100’ PSSIZE PCI to System CPU Address space Size 81 BAR + x’000F 8120’ BARPS CPU Base Address Register 83 BAR + x’000F 8140’ PSBAR System Base Address Register for PCI-32 84 3 BAR + x’000F 8150’ PPBAR PCI-64 Base Address Register for PCI-32 84 3 BAR + x’000F 8200’ BPMDLK Bottom of Peripheral Memory space with potential deadlock 85 BAR + x’000F 8210’ TPMDLK Top of Peripheral Memory space with potential deadlock 86 BAR + x’000F 8220’ BIODLK Bottom of Peripheral I/O space with potential deadlock 87 BAR + x’000F 8230’ TIODLK Top of Peripheral I/O space with potential deadlock 88 BAR + x’000F 8300’ IT_ADD_RESET PCI-64 Reset Interrupt (INT1) Addressed Register 89 4 BAR + x’000F 8310’ INT_SET Set of G_INTA, G_INTB, G_INTC, G_INTD on PCI-64 90 4 Channel Status Register 91 Processor Load/Store Status Register 92 BAR + x’000F 9800’ CSR BAR + x’000F 9810’ PLSSR 1. 2. 3. 4. Read-Only Register, write is ignored Little Endian registers Only for PCI-32 Only for PCI-64 CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 63 of 209 IBM Dual Bridge and Memory Controller PCI Slave Error Address Register (PSEA) This register is used to log the PCI address when an error occurs during Device PCI slave transfer. See PCI Master Error Handling on page 193 for additional details. This register is reset to zero when occurs a Powergood or when one of the bit RSTR[2] of the , “Connectivity Reset Register (RSTR)” Page 98 for PCI 32 or bit RSTR[3] for PCI 64 is forced to zero or from a, “Software Power On Reset Control Register (SPOR)” Page 99 reset. Reset Value x’0000 0000’ Address BAR + x’000F 6110’ Access Type Read Only PCI To Memory Error Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 . Bit(s) 0 - 31 Description PCI To Memory Error Address. Contains the address present on the PCI bus when an error occurs during a PCI transfer. Page 64 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Diagnostic Register (PCIDG) This register contains two mode bits that are used for special modes of operation. Address BAR + x’000F 6120’ Access Type Read/Write DMA Pipeline Enable PCI-32 PCI-64 64-bit Mode Enable Reset Value 0 1 x’4000 0000’ x’C000 0000’ Reserved - Must Leave at 0 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 64-bit Mode Enable 0: Operates as a 32-bit bridge. G_REQ64 and G_ACK64 never activated by device. 1: Operates as a 64-bit bridge. G_REQ64 always activated for device initiated transfers. 1 DMA Pipeline Enable 0: DMA transfers are NOT pipelined internal to device. Results in significantly lower bandwidth to PCI bus. 1: DMA transfers are pipelined internal to device for maximum bandwidth. 2 - 31 Reserved. Must Leave At 0 CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 65 of 209 IBM Dual Bridge and Memory Controller Interrupt Acknowledge Cycle (INTACK) A read to the INTACK register generates an Interrupt Acknowledge Cycle on the PCI bus. An Interrupt Acknowledge Transaction has no addressing mechanism and is implicitly targeted to the interrupt controller in the system. The vector is returned by the interrupt controller when TRDY is asserted. Address BAR + x’000F 7700’ Access Type Read Only INTA 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description This register is a port through to the PCI bus. Writes to this register are ignored. Page 66 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Base Address for I/O (PIBAR) Reset Value x’0000 0000’ Address BAR + x’000F 7800’ Access Type Read/Write PCI Base Address 0 1 2 3 4 5 6 7 Reserved 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 11 PCI Base Address. Contains the upper bits of the PCI base address that PCI I/O is mapped to. Note: Address must be aligned on boundary equal to size specified in PCI I/O Size register 12 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 67 of 209 IBM Dual Bridge and Memory Controller PCI Base Address for Memory (PMBAR) Reset Value x’0000 0000’ Address BAR + x’000F 7810’ Access Type Read/Write PCI Base Address 0 1 2 3 4 5 6 7 Reserved 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 11 PCI Base Address. Contains the upper bits of the PCI base address that PCI Memory is mapped to. Note: Address must be aligned on boundary equal to size specified in PCI Memory Size register. 12 - 31 Reserved Page 68 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Component Reset Register (CRR) This register provides software with a means to disable all devices on the PCI bus by writing a zero in bit 0. x’0000 0000’ Address BAR + x’000F 7EF0’ Access Type Read/Write Device 0 Reset Reset Value 0 Reserved 1 2 3 4 Reserved 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 Device 0 Reset 0: Reset signal active 1: Reset signal inactive 1-5 Reserved. Must be left to 1 6 - 31 Reserved. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 69 of 209 IBM Dual Bridge and Memory Controller Personalization Register (PR) 0 5 6 7 8 9 Issue Flush Snoops not Kill Snoops Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-1 Grant Active To Frame Active Time-out Disable 4 PCI-ISA Bridge Deadlock Avoidance Disable 3 G/P_IRDY Count 2 1 G/P_TRDY Count Read/Write ARB Level To Park Access Type PCI Master Address Translation Disable BAR + x’000F 7F20’ Machine Check Processor Address Deadlock Avoidance Signal Selection x’0000 0000’ Parking Control Reset Value PCI Queue Enable This register provides additional programmability of the PCI Bridge logic. Description Parking Control 0x: Bus is parked on device 10: MRU algorithm for parking 11: Park specified ARB level below in bits 5-7 2 Deadlock Avoidance Signal Selection (PCI-32 Bridge Only) To avoid deadlocks with PCI-ISA bridges on the PCI 32-bit bridge, the bridge must indicate to the device that a PCI access is about to occur before the P/G_GNT signal is activated. Any posted PCI 32-bit bus transfers must be flushed prior to activating the P/G_GNT signal and any accesses to the PCI 32-bit bus must be disabled after the GNT is given and continue disabled until the PCI access is complete and the P/G_GNT signal is removed. The PCI-ISA bridge must not grant the secondary ISA bridge until device has activated the P/G_GNT signal. Device provides two input signals for this purpose that are selectable with this bit. 0: Selects the P/G_REQ[5] signal. P/G_GNT[5] indicates buffers flushed and any PCI. Transfers will be disabled on the 60x bus until the P/G_REQ[5] signal is deactivated. 1: Selects the P/G_REQ signal. P/G_REQ indicates buffers flushed and any PCI. Transfers will be disabled on the 60x bus until the P/G_REQ signal is deactivated 3 Machine Check Processor. If an error is detected as a target during a PCI access operation, the device generates a Machine Check to the proceso specified by the value of this register. 0: PCI bridge logic machine checks processor 0 1: PCI bridge logic machine checks processor 1 4 PCI Master Address Translation Disable 0: PCI Master addresses are always translated before being presented to system memory 1 PCI Master addresses are NOT translated and sent directly to system memory Page 70 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bit(s) Description 5-7 ARB Level To Park. Contains the encoded arbitration level to park when bus is idle: For PCI-64, level 000 is for device, level 001 for agent 0 and so on. For PCI-32, level 000 is for agent 0, level 001 for agent 1 and so on. 8 - 11 IRDY Count. Contains the number of PCI clocks times 8 that device waits before detecting a time-out condition. A value of zero disables the time-out check. 12 - 15 TRDY Count. Contains the number of PCI clocks times 8 that device waits before detecting a time-out condition. A value of zero disables the time-out check. 16 PCI Queue Enable 0: PCI logic does not queue requests 1: PCI logic queues up to two operations 17 PCI-ISA Bridge Deadlock Avoidance Disable 0: PCI-ISA Bridge is present in the system. Therefore, device will: 1) NOT deactivate P/G_GNT[5] even if other REQs become active (other REQs internally gated) 2) not activate P/G_GNT[5] until 60x bus has flushed all posted PCI 32-bit bus transfers. 1: PCI-ISA Bridge is NOT present in system, so device treats the P/G_REQ[5] signal like any other PCI bus REQ signal. 18 Grant Active To Frame Active Time-out Disable 0: If device grants the PCI bus to a PCI master and other REQs are outstanding, the PCI master must activate the FRAME signal within 20 cycles or device will deactivate its GNT signal. 1: Once device has granted the bus to a PCI device, Device waits until it sees FRAME active from that device before deactivating its grant signal. Note: The 20 cycle count is not guaranteed. The timer runs continuously and therefore device could remove the grant at any time. 19 20-31 Issue Flush Snoops Instead Of Kill Snoops 0: PCI bridge requests the 60x logic to perform Kill snoops on 60x bus for DMAs as normal. 1: PCI bridge substitutes Flush snoops instead of Kill snoops to the 60x logic. This is to avoid a 604 coherency problem that exists for Kill snoop operations. Reserved The following table describes how to program this register. Personalization Register Settings Register Bits Configuration 0-1 2 3 Initial Bringup 00 0 Normal Settings 10 0 4 5-7 8-11 12-15 16 m 0 000 0000 0000 0 m 0 000 1111 1111 1 17-31 Note: m = Machine Check Processor bit is set to 0 if processor installed in CPU Slot 0, and set to 1 if processor installed in CPU Slot CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 71 of 209 IBM Dual Bridge and Memory Controller Arbiter Control Register (ACR) This register provides software with a means to disable individual devices on the PCI bus from generating master bus operations. ARB Level 5 Enable ARB Level 6 Enable ARB Level 7 Enable Read/Write ARB Level 4 Enable Access Type ARB Level 3 Enable BAR + x’000F 7F30’ ARB Level 2 Enable Address ARB Level 1 Enable x’0000 0000’ ARB Level 0 Enable Reset Value 0 1 2 3 4 5 6 7 Reserved 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 ARB Level 0 Enable 0: ARB level is ignored 1: ARB level is enabled 1 ARB Level 1 Enable 2 ARB Level 2 Enable 3 ARB Level 3 Enable 4 ARB Level 4 Enable 5 ARB Level 5 Enable 6 ARB Level 6 Enable 7 ARB Level 7 Enable (Not supported in 32-bit PCI bridge) 8-31 Reserved Page 72 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Memory Address Space Size (MSIZE) Reset Value x’FFF0 0000’ Address BAR + x’000F 7F40’ Access Type Read/Write PCI Memory Address Space Size 0 1 2 3 4 5 6 7 8 9 Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-11 PCI Memory Address Space Size x’FFF’ 1 MB x’FFE’ 2 MB x’FFC’ 4 MB x’FF8’ 8 MB x’FF0’ 16 MB x’FE0’ 32 MB x’FC0’ 64 MB x’F80’ 128 MB x’F00’ 256 MB x’E00’ 512 MB x’C00’ 1 GB x’800’ 2 GB x’000’ 4 GB 12-31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 73 of 209 IBM Dual Bridge and Memory Controller PCI I/O Address Space Size (IOSIZE) Reset Value x’FFF0 0000’ Address BAR + x’000F 7F60’ Access Type Read/Write PCI I/O Address Space Size 0 1 2 3 4 5 6 7 8 Reserved 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-11 PCI I/O Address Space Size x’FFF’ 1 MB x’FFE’ 2 MB x’FFC’ 4 MB x’FF8’ 8 MB x’FF0’ 16 MB x’FE0’ 32 MB x’FC0’ 64 MB x’F80’ 128 MB x’F00’ 256 MB x’E00’ 512 MB x’C00’ 1 GB x’800’ 2 GB x’000’ 4 GB 12-31 Reserved Page 74 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System Base Address for PCI Memory (SMBAR) Reset Value x’A000 0000’ Address BAR + x’000F 7F80’ Access Type Read/Write System Base Address 0 1 2 3 4 5 6 7 8 Reserved 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 11 System Base Address. This register contains the upper bits of the SYSTEM address that PCI Memory is mapped to. Note: Address must be aligned on a boundary equal to the size specified in PCI Memory Size register. 12 - 31 Reserved Note: Address is decoded only if the Master Enable bit in the PCI Command Register is on. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 75 of 209 IBM Dual Bridge and Memory Controller System Base Address for PCI I/O (SIBAR) Reset Value x’8000 0000’ Address BAR + x’000F 7FC0’ Access Type Read/Write PCI Base Address 0 1 2 3 4 5 6 7 Reserved 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 11 System Base Address This register contains the upper bits of the SYSTEM address that PCI I/O is mapped to. Note: Address must be aligned on boundary equal to size specified in PCI I/O Size register. 12 - 31 Reserved Note: Address is decoded only if the Master Enable bit in the PCI Command Register is on. Page 76 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PHB Configuration Register (CTLRW) This register is primarily used by software to program device for a particular address translation mode. ISA Contiguous Mode ISA Compatibility Mode Reserved Reserved Read/Write Create Interrupt on PHB Detected Error Access Type G\P_SERR Presentation BAR + x’000F 7FD0’ 64-Bit Mode Enable Address Extensions Enable x’0200 0000’ Reserved Reset Value 0 1 2 3 4 5 6 7 8 Reserved 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 Reserved 1 Extensions Enable. Read Only. 0: Device does not perform extended error recovery 2 64-Bit Mode Enable. Read Only. 0: Device does not support 64-bit addresses 3 SERR Presentation. Read Only. 0: PCI Bridge always generates Machine Check if G/P_SERR driven active 4 Create Interrupt On PHB Detected Error. Read Only. 0: PCI Bridge always generates Machine Check for PHB detected error 5 ISA Contiguous Mode This bit programs how device translates the first 8 MB of PCI I/O space. See Noncontiguous I/O Address Mode Enabled on page 145 for additional details. 0: ISA space is contiguous 1: ISA space is not-contiguous 6 ISA Compatibility Mode. Read Only. 1: Device contains an external pin for this function (P_ISA_MASTER). 7 Reserved 8 Reserved 9-31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 77 of 209 IBM Dual Bridge and Memory Controller PHB Configuration Register (CTLRO) This register is the primary indicator to software that device contains the PCI extensions specified in the IBM PHB architecture. It also provides bridge capability information to software. 0 1 2 3 4 5 x’9006 0000’ x’9004 0000’ Reserved 6 7 8 9 Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-1 Number of Interrupts Supported Read Only Dual Address Cycle Support Access Type Executable PCI Memory Support BAR + x’F000 7FE0’ Lock Support Address 64-Bit Mode Support PCI-32 PCI-64 PHB Extension Support Reset Value Description PHB Extension Support 10: Device supports error detection extensions but NOT error recovery 2 64-Bit Mode Support 0: NOT supported 3 Lock Support 1: Full support of PCI lock bus cycles 4 Executable PCI Memory Support 0: NOT supported 5 Dual Address Cycle Support 0: NOT supported 6 - 15 Reserved 16 - 19 Number Of Interrupts Supported 0000: No interrupts supported 20 - 31 Reserved Page 78 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller CONFIG_ADDRESS Register (CFGA) Access Type Read/Write Reserved Bus Number 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 Always b’00’ BAR + x’000F 8000’ Register Number Address Function Number x’0000 0000’ Configuration Enable Reset Value Device Number This Little Endian register, along with the CONFIG_DATA register, provides software with a means to configure the PCI bus. Device implements Configuration Mechanism #1 as specified in the PCI Local Bus Specification. See heading Configuration Cycles on page 190 for additional details. 4 3 2 1 0 Bit(s) Description 31 Configuration Enable 0: Disabled 1: Enabled, accesses to the CONFIG_DATA register result in device executing a configuration access to itself or to the PCI bus. 30 - 24 Reserved 23 - 16 Bus Number. Specifies which PCI bus is being configured. Device checks this field to determine the appropriate configuration action. 15-11 Device Number. Selects a particular device to be configured on a bus. 10-8 Function Number. For devices that implement more than one function, this field specifies which function to configure within a device. 7-2 Register Number. Specifies which register out of the 256-byte PCI Configuration header to access 1-0 Always b’00’ CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 79 of 209 IBM Dual Bridge and Memory Controller CONFIG_DATA Register (CFGD) Reset Value x’0000 0000’ Address BAR + x’000F 8010’ Access Type Read/Write CFGD 31 30 29 28 27 26 25 24 23 22 21 20 19 18 17 16 15 14 13 12 11 10 9 8 7 6 5 4 3 2 1 0 Bit(s) Description 31 - 0 Virtual 32-bit Register. When this Little Endian register is accessed in Read or Write, the device initiates a PCI Configuration Read or Write cycle of external PCI devices, the address of which is provided by the PCI CONFIG_ADDRESS Register. Page 80 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System Address Space SIZE for PCI (PSSIZE) This is the same definition for 32-bit PCI and 64-bit PCI. x’0000 0000’ Address BAR + x’000F 8100’ Access Type Read/Write Enable Memory or I/O Space Reset Value Reserved 0 1 2 3 4 5 6 7 Reserved 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-6 7 8 - 23 24 - 31 System Address Space Size Description Reserved Enable Memory Or IO Space 0: Memory Space 1: IO Space Reserved System Address Space Size x’FF’: 16 MB x’FE’: 32 MB x’FC’: 64 MB x’F8’: 128 MB x’F0’: 256 MB x’E0’: 512 MB x’C0’: 1 GB x’80’: 2 GB x’00’: 4 GB CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 81 of 209 IBM Dual Bridge and Memory Controller Other PCI Address Space SIZE for PCI (PPSIZE) This is the same definition for 32-bit PCI and 64-bit PCI. x’0000 0000’ Address BAR + x’000F 8110’ Access Type Read/Write Enable Memory or I/O Space Reset Value Reserved 0 1 2 3 4 5 6 7 Reserved 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-6 7 8 - 23 24 - 31 Other Address Space Size Description Reserved Enable Memory or IO Space 0: Memory Space 1: IO Space Reserved Other Address Space Size x’FF’ 16 MB x’FE’ 32 MB x’FC’ 64 MB x’F8’ 128 MB x’F0’ 256 MB x’E0’ 512 MB x’C0’ 1 GB x’80’ 2 GB x’00’: 4 GB Page 82 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System Base Address Register (BARPS) The definition is the same for 32-bit PCI and 64-bit PCI. Reset Value x’0000 0000’ Address BAR + x’000F 8120’ Access Type Read/Write Reserved 0 1 2 3 4 5 6 7 8 9 System Base Address 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 23 Reserved 24 - 31 System Base Address. Contains the upper bits of the system Base address that Memory is mapped to. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 83 of 209 IBM Dual Bridge and Memory Controller System Base Address Register for PCI-32 (PSBAR) Only the PCI-32 bit bridge has this register. Reset Value x’0000 0000’ Address BAR + x’000F 8140’ Access Type Read/Write Reserved 0 1 2 3 4 5 6 7 8 9 System Base Address for PCI-32 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 23 Reserved 24 - 31 System Base Address for PCI-32. Contains the upper bits of the System Base address that memory is mapped to. Page 84 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bottom of Peripheral Memory Space With Potential Deadlock (BPMDLK) Reset Value x’0000 0000’ Address BAR + x’000F 8200’ Access Type Read/Write Reserved 0 1 2 3 4 5 Bottom of Peripheral Memory Space 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-9 Bottom of Peripheral Memory Space. Contains the bottom address for the CPU to PCI MEMORY access with potential deadlock 10 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 85 of 209 IBM Dual Bridge and Memory Controller Top of Peripheral Memory Space With Potential Deadlock (TPMDLK) Reset Value x’0000 0000’ Address BAR + x’000F 8210’ Access Type Read/Write Reserved 0 1 2 3 4 5 Top of Peripheral Memory Space 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-9 Top of Peripheral Memory Space. Contains the top address for the CPU to PCI MEMORY access with potential deadlock 10 - 31 Reserved Page 86 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bottom of Peripheral I/O Space With Potential Deadlock (BIODLK) Reset Value x’0000 0000’ Address BAR + x’000F 8220’ Access Type Read/Write Reserved 0 1 2 3 4 5 Bottom of Peripheral I/O Space 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-9 10 - 31 Description Bottom of Peripheral IO Space. Contains the bottom address for the CPU to PCI IO access with potential deadlock Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 87 of 209 IBM Dual Bridge and Memory Controller Top of Peripheral I/O Space With Potential Deadlock (TIODLK) This register exists on PCI-32 and PCI-64. Reset Value x’0000 0000’ Address BAR + x’000F 8230’ Access Type Read/Write Reserved 0 1 2 3 4 5 Top of Peripheral I/O Space 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-9 10 - 31 Description Top of Peripheral I/O Space. Contains the top address for the CPU to PCI IO access with potential deadlock Reserved Page 88 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Reset Addressed Interrupt Register (IT_ADD_RESET) This Virtual register exists only for PCI-64 bridge. Only the CPU can write to this register and reset the IT1 output interrupt signal. Address BAR + ’000F 8300’ Access Type Write Only Reset_addit 0 1 2 3 4 5 Reserved 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-7 Reset_addit 1: Writing a 1 in one of these 8 bits resets the interrupt signal INT1 0: No action 8 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 89 of 209 IBM Dual Bridge and Memory Controller Set PCI-64 Interrupt Register (INT_SET) This register exits only for PCI-64, Interrupt can be set only by the CPU. Address BAR + ’000F 8310’ Access Type Write Only Set_It 0 1 2 Reserved 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-3 Set_It Writing 1 by the CPU sets the bit corresponding Writing 0 has no action Bit 0: INTA Bit 1: INTB Bit 2: INTC Bit 3: INTD 4 - 31 Reserved Page 90 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Channel Status Register (CSR) This register is used to log errors during PCI Master to system transfers. Please see PCI Master Error Handling on page 193 for additional details. 2 3 4 5 6 7 PCI-PCI Error 1 Bus Time-out 0 Memory Error Read/Write Reserved Access Type Invalid Memory Address BAR + ’000F 9800’ G/P_SERR Detected Address PCI Bus Address Parity Detected x’0000 0000’ Reserved Reset Value 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Arbitration Level Bit(s) 0-1 Reserved Description Reserved 2 PCI Bus Address Parity Detected 0: No Error 1: PCI Bridge detected address parity error 3 SERR Detected 0: No Error 1: PCI Bridge detected G/P_SERR during transaction 4 Invalid Memory Address 0: No Error 1: PCI access occurred to invalid system memory address 5-7 Reserved 8 Memory Error 0: No Error 1: Double bit ECC error occurred during memory access 9 Bus Time-out 0: No Error 1: PCI Bridge detected bus time-out; no IRDY detected 10 PCI - PCI Error 0: No Error 1: Error occurred during PCI to PCI bridge access 11 - 15 Arbitration Level. Encoded arbitration level of PCI device when error occurred 16 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 91 of 209 IBM Dual Bridge and Memory Controller Processor Load/Store Status Register (PLSSR) This register provides error status information for all transfers initiated by the CPU, a PCI master, or the other PCI Bridge logic. Please see Error Handling for CPU-Initiated Transactions on page 162 for additional details on this register. Read/Write 0 Retry Count Expired Access Type PCI Bus Timeout BAR + x’000F 9810’ No G/P_DEVSEL Address G/P_SERR Detected x’0000 0000’ Reserved Reset Value 2 3 4 5 1 Reserved 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-1 Description Reserved 2 SERR Detected 0: No Error 1: PCI Bridge detected G/P_SERR active during master operation 3 No Devsel 0: No Error 1: PCI Bridge did not receive G/P_DEVSEL during master operation 4 PCI Bus Timeout 0: No Error 1: PCI Bridge detected bus time-out; no G/P_TRDY detected 5 Retry Count Expired 0: No Error 1: PCI Bridge detected bus time-out, too many retry’s 6 - 31 Reserved Page 92 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Standard System Registers Space Standard System Registers List (Page 1 of 3) Address Name x’FF00 0000’ to x’FF00 0007’ Use Page Notes Reserved Standard System Registers x’FF00 0008’ PIDR Physical Identifier Register 96 1 x’FF00 000C’ CNFR Connectivity Configuration Register 97 see p 33 x’FF00 0010’ RSTR Connectivity Reset Register 98 x’FF00 00E8’ SPOR Software POR Register 99 x’FF00 1000’ UCTL Device & System Control Register 100 x’FF00 1010’ MPSR Multi-Processor Semaphore Register 102 x’FF00 1020’ SIOC System I/O Control 103 x’FF00 1030’ ABCNTL 60x Arbiter Control Register 104 x’FF00 1040’ SRST CPU Soft Reset Register 106 x’FF00 1050’ ERRC Error Control Register 107 x’FF00 1060’ SESR System Error Status Register 108 x’FF00 1070’ SEAR System Error Address Register 110 7 Specific System Registers x’FF00 1080’ Reserved x’FF00 1100’ PGCHP Chip program Register 111 x’FF00 1110’ RGBAN1 Free Register 1 113 x’FF00 1120’ RGBAN2 Free Register 2 114 x’FF00 1130’ GPDIR GPIO Direction Register 115 x’FF00 1140’ GPIN GPIO Input Register 116 x’FF00 1150’ GPOUT GPIO Output Register 117 x’FF00 1160’ ATAS Address Transfer Attribute for Snoop Reg 118 x’FF00 1170’ AVDG Device Diagnostic Register 119 x’FF00 1174’ to x’FF00 11FF’ x’FF00 1200’ Reserved MCCR x’FF00 1210’ 1. 2. 3. 4. 5. 6. 7. 8. 7 Memory Controller Control Register 121 Reserved x’FF00 1220’ MESR Memory Error Status Register 123 x’FF00 1230’ MEAR Memory Error Address Register 124 x’FF00 1300’ MCER0 Memory Configuration Extent Register 0 125 RO: Read Only Register All bits can be read. Only bits [4:31] can be written All bits can be read. Only bits [0:3] can be written Four beat burst read operations allowed to this address space; Single byte writes only Not decoded by system logic Byte accesses allowed WO: Write Only Register Range that IBM Dual Bridge and Memory Controller responds to is programmable CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 93 of 209 IBM Dual Bridge and Memory Controller Standard System Registers List (Page 2 of 3) Address Name x’FF00 1310’ MCER1 Memory Configuration Extent Register 1 125 x’FF00 1320’ MCER2 Memory Configuration Extent Register 2 125 x’FF00 1330’ MCER3 Memory Configuration Extent Register 3 125 x’FF00 1340’ MCER4 Memory Configuration Extent Register 4 125 x’FF00 1350’ MCER5 Memory Configuration Extent Register 5 125 x’FF00 1360’ MCER6 Memory Configuration Extent Register 6 125 x’FF00 1370’ MCER7 Memory Configuration Extent Register 7 125 x’FF00 1400’ SIOR0 SIO Register 0 (DIMM PDs) 127 1 128 1 x’FF00 1410’ x’FF00 1420’ Use Page Notes Reserved SIOR1 SIO Register 1 (Planar, DIMM, CPU, etc.) x’FF00 1424 to x’FF00 1FFF’ Reserved x’FF00 2000 to x’FF00 3FFF’ Reserved SIO Address Space x’FF00 4000 to x’FF00 7FFF’ SIOA1 System I/O Address Space 1 x’FF00 8000 to x’FF0F FFFF’ Reserved x’FF10 0000 to x’FF17 FFFF’ Reserved 100 DMA Registers: User Privilege x’FF18 0000 to x’FF1C 001F’ Reserved x’FF1C 0020’ GSCR Global Control Register (user) 129 1 x’FF1C 0030’ GSSR Global Status Register (user) 130 1 x’FF1C 0040’ XSCR Transfer Control Register (user) 131 x’FF1C 0050’ XSSR Transfer Status Register (user) 132 1 x’FF1C 0070’ XPAR Transfer PCI Address Register (user) 134 2 x’FF1C 0090’ XWAR Transfer Write Back Address Register (user) 135 1 x’FF1C 00A0’ XTAR Transfer Translated Address Register (user) 136 1 x’FF1E 0020’ GSCR Global Control Register (priv) 129 x’FF1E 0030’ GSSR Global Status Register (priv) 130 x’FF1E 0040’ XSCR Transfer Control Register (priv) 131 x’FF1E 0050’ XSSR Transfer Status Register (priv) 132 1 3 x’FF1E 0070’ XPAR Transfer PCI Address Register (priv) 134 x’FF1E 0090’ XWAR Transfer Write Back Address Register (priv) 135 x’FF1E 00A0’ XTAR Transfer Translated Address Register (priv) 136 x’FF1E 00A4’ to x’FF1F FFFF’ 1. 2. 3. 4. 5. 6. 7. 8. 1 1 Reserved RO: Read Only Register All bits can be read. Only bits [4:31] can be written All bits can be read. Only bits [0:3] can be written Four beat burst read operations allowed to this address space; Single byte writes only Not decoded by system logic Byte accesses allowed WO: Write Only Register Range that IBM Dual Bridge and Memory Controller responds to is programmable Page 94 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Standard System Registers List (Page 3 of 3) Address Name Use Page Notes System Standard Configuration Registers x’FF20 0000’ DCR Device Characteristics Register 137 1 x’FF20 0004’ DID Device ID Register 138 1 Base Address Register 139 see p. 33 PCI BAR Enable Register 140 x’FF20 0008’ to x’FF20 0014’ Reserved x’FF20 0018’ x’FF20 0020’ to x’FF20 0FFF’ BAR Reserved Device Specific Configuration Space x’FF20 1000’ PCIENB x’FF20 1004’ to x’FFBF FFFF’ Reserved SIO Address Space 2 x’FFC0 0000’ to x’FFC3 FFF’ SIOA2 x’FFC4 0000’ to x’FFDF FFFF’ System I/O Address Space 2 CPC710 & System Control (UCTL) on page 100 Reserved BOOT ROM x’FFE0 0000’ to x’FFFF FFFF’ 1. 2. 3. 4. 5. 6. 7. 8. IPLROM FLASH ROM: Up to 2 MB 4, 6, 8 RO: Read Only Register All bits can be read. Only bits [4:31] can be written All bits can be read. Only bits [0:3] can be written Four beat burst read operations allowed to this address space; Single byte writes only Not decoded by system logic Byte accesses allowed WO: Write Only Register Range that IBM Dual Bridge and Memory Controller responds to is programmable CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 95 of 209 IBM Dual Bridge and Memory Controller Physical Identifier Register (PIDR) This register provides a unique number for each processor (or any 60x bus master) reading this location. It is primarily used by processors to differentiate themselves in multiprocessor configurations. When this register is read, device latches the current processor’s SYS_BR/SYS_BG pair into this register which physically identifies the processor. Each processor has a unique SYS_BR/SYS_BG pair connected to it. Reset Value x’0000 0000’ Address x‘FF00 0008’ Access Type Read/Write Reserved 0 1 2 3 4 5 6 7 8 9 Physical Identifier 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 23 Reserved 24 - 31 Physical Identifier. Device responds with two values for this field: x’00’: Indicates processor associated with BR0 and BG0 pins. x’01’: Indicates processor associated with BR1 and BG1 pins Page 96 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Connectivity Configuration Register (CNFR) The CNFR register described below is used to support the initialization and configuration of devices on the 60x bus. This register provides the unique setup signal required to insure that only one device will respond to configuration addresses at a time. Software must adhere to the following restrictions for configuration: • A write to the CNFR register must be followed by a SYNC operation or a read of the register. • Software must issue a read to the Device Characteristics Register (DCR) at x’FF20 0000’ to determine if a device is present. x’0000 0000’ Address x‘FF00 000C’ Access Type Read/Write Configuration Enable Reset Value 0 configuration Field • If software receives a x’F000 0000’ response from the DCR read, this indicates that no device is present and therefore no other configuration registers should be accessed. Access to other configurations registers will result in a bus time-out condition. Reserved 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 Description Configuration Enable 0: Inactivate all SYS_CONFIG[n] signals 1: Activate appropriate SYS_CONFIG[n] as described in bits 30 - 31 1 - 29 Reserved 30 - 31 Configuration Field 00: SYS_CONFIG0. SYS_CONFIG0 signal driven active 01: SYS_CONFIG1. SYS_CONFIG1 signal driven active 10: SYS_CONFIG2. Configuration access directed to PCI-32 bus 11: SYS_CONFIG3. Configuration access directed to PCI-64 bus See 60x Bus Configuration on page 161 for details on configuration bus cycles and procedures. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 97 of 209 IBM Dual Bridge and Memory Controller Connectivity Reset Register (RSTR) This register provides a means to individually reset devices on the 60x bus. Bits 0 and 1 directly control SYS_HRESET0 and SYS_HRESET1 respectively. The remaining two bits control reset signals that are internal to device. Access Type Read/Write Reset for PCI-64 Bus Bridge x‘FF00 0010’ Reset for PCI-32 Bus Bridge Address Reset for 2nd Processor x’C000 0000’ Reset for 1st Processor Reset Value 0 1 2 3 Reserved 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 Reset For 1st Processor 0: SYS_HRESET0 signal is active 1: SYS_HRESET0 signal is inactive 1 Reset For 2nd Processor 0: SYS_HRESET1 signal is active 1: SYS_HRESET1 signal is inactive 2 Reset for PCI 32 Bus Bridge 0: Reset signal active 1: Reset signal is inactive 3 Reset for PCI-64 Bus Bridge 0: Reset signal active 1: Reset signal is inactive 4 - 31 Reserved Page 98 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Software Power On Reset Control Register (SPOR) This register provides a mechanism for software to initiate a hard reset to the system. The device will activate resets to all processors and I/O devices. Reset Value x’0000 0000’ Address x‘FF00 00E8’ Access Type Write Only Generate Hard Reset 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Definition Generate Hard Reset A write to this register will initiate a power on reset. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 99 of 209 IBM Dual Bridge and Memory Controller Specific System Registers Space CPC710 & System Control (UCTL) 2 3 6 7 8 9 Reserved Description 0 Reserved 1 Reserved. R/W System I/O Address Space 1 Enable 00: Accesses to this address range inhibited 01: Accesses only allowed to FF00 4000 - FF00 5FFF (unpredictible results) 10: Accesses only allowed to FF00 6000 - FF00 7FFF (unpredictible results) 11: Accesses to entire address range allowed (unpredictible results) 4 Boot Flash Write Disable 0: Indicates that writes are allowed to Boot FLASH space 1: Writes to Boot FLASH space are inhibited 5 DMA Transfer Address Space Enable 0: Accesses to DMA Address Range allowed 1: Accesses to DMA Address Range inhibited 6 System I/O Address Space 2 Enable 0: Accesses to FFC0 0000 - FFC3 FFFF disabled 1: Accesses to FFC0 0000 - FFC3 FFFF enabled (unpredictible results) 7 Reserved 8 - 11 EC Level 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 2-3 Kill Snoop Operation 5 Reserved 4 Resource ID Reserved 1 Reserved 0 System I/O Address Space 2 Enable Read/Write DMA Transfer Address Space Enable Access Type Boot Flash Write Disable x‘FF00 1000’ System I/O Address Space 1 Enable Address Reserved x’0008 0090 Configuration Enable Reset Value Time Base Enable This register is used to enable address ranges to be decoded by the CPC710 and processor related operations. Resource ID. This 4-bit field contains the Resource ID that device uses to determine whether or not it is the target of a DMA transfer operation. Page 100 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bit(s) 12 13 - 14 Description Time Base Enable 0: The Time Base Enable signal to the CPU is deactivated. CPU real time clocks halted 1: The Time Base Enable signal SYS_TBE to the CPU is activated. CPU real time clocks enabled Reserved 15 Reserved R/W 16 Kill Snoop Operation 0: Device issues Kill address only transaction types for full cache line invalidates 1: Device issues Flush address only transaction type for full cache line invalidates 17 - 23 Reserved 24 - 31 Device EC LEVEL. Read only Bit 24 always at one Bits 25 to 27 main Engineering changes Bits 28 to 31 for sub Engineering changes 1000 0000 for CPC710_100 CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 101 of 209 IBM Dual Bridge and Memory Controller Multi-Processor Semaphore (MPSR) Address x‘FF00 1010’ Access Type Read/Write Multi-processor Synchronization Bit 1r x’0000 0000’ Multi-processor Synchronization Bit 0 Reset Value 0 1 Multi-processor First Access Bit This register is used by the IPL boot code to facilitate bring-up of processors in an MP environment. It provides a first access bit, BIT 31, that allows a method for processors to determine which processor is the master, since both processors are active after power on. BIT 31 contains a value of 0 after power on reset. When the first processor read occurs to this register, BIT 31 returns a value of 0. All subsequent reads of this register return a value of 1 for BIT 31. In addition to the First Access Bit, bits 0 and 1 provide semaphores for use by the firmware during boot time and are utilized until system memory has been initialized and tested. Reserved 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 Multi-processor Synchronization Bit 0. Used for communication between processors at IPL time 1 Multi-processor Synchronization Bit 1. used for communication between processors at IPL time 2 - 30 31 Reserved Multi-processor First Access Bit. Read Only; Set after read 0: Initial power on value; Indicates first read of this register. 1: Indicates that this register has been read at least once previously. Page 102 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System I/O Control (SIOC) This register provides initialization and control of the Boot FLASH devices to which device interfaces. x’0000 0000’ Address x‘FF00 1020’ Access Type Read/Write Reserved Boot Flash Size Reset Value 0 1 2 Reserved 3 4 5 6 7 Reserved 8 9 Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 SIO Diagnostic/debug Control Description Reserved. R/W 1-3 Boot Flash Size 000: 2.0 MB - Device initiates FLASH access for addresses x’FFE0 0000’ to x’FFFF FFFF’ 001: 1.0 MB - Device initiates FLASH access for addresses x’FFF0 0000’ to x’FFFF FFFF’ 011: 0.5 MB - Device initiates FLASH access for addresses x’FFF0 0000’ to x’FF7F FFFF’ 111:Reserved 4-8 Reserved 9 - 11 Reserved. These bit should be left to zero. 12 - 15 Reserved 16 - 31 SIO Diagnostic/debug Control. Must Leave At Zero; Do Not Change 16-17 Controls SIO_TT1 signal 18-23 Controls PROC ID output 24-27 Controls asynchronous boundary 28-29 Controls SIO_TS signal 30-31 Controls SIO_TA signal CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 103 of 209 IBM Dual Bridge and Memory Controller -60x Arbiter Control Register (ABCNTL) 1 2 3 4 5 6 7 8 Bit(s) Reserved DBG Control Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Reserved 9 DBG Park Control 64-Byte Cache Line Pipeline Control 0 Activate SYS_TA Signal Pre-charge Read/Write Eieio Retry Disable Access Type Endian Mode x‘FF00 1030’ Data Gather Control for PCI-64 Bus Address Data Gather Control for PCI-32 Bus x’0000 0000’ Address Bus Parking Control Reset Value Extend Address Tenure This register provides extensive control over the 60x bus arbiter operation. For a detailed description of the 60x bus arbiter, see section 60x Bus Arbiter Description on page 152. Reserved Description 0-1 Pipeline Control 00: Pipelining Disabled 01: One level pipelining per arbitration level is enabled (two outstanding addresses allowed) 10: Two level pipelining per arbitration level is enabled (three outstanding addresses allowed) 11: One level pipeline enabled across both arbitration levels; Selected this mode for operation with an L2 look aside controller. 2-3 Address Bus Parking Control 00: Parking Disabled 01: Parking enabled for Arbitration level 0 only 10: Parking enabled for Arbitration level 1 only 11: MRU parking enabled; Last arbitration level active is parked. 4 64-Byte Cache Line 0: Arbiter will grant the address bus as normal 1: Arbiter will grant a second address bus tenure to the current arbitration level, if the current arbitration level is again requesting the address bus and if first access is a burst transaction. Normal round robin grant sequence will resume after each pair of grants. 5-6 Data Gather Control for PCI-32 bus 0x: Not enabled 10: Enabled for accesses to incrementing addresses only 11: Enabled for accesses to incrementing and same addresses - NOT RECOMMENDED 7-8 Data Gather Control for PCI-64 bus 0x: Not enabled 10: Enabled for accesses to incrementing addresses only 11: Enabled for accesses to incrementing and same addresses - NOT RECOMMENDED Page 104 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bit(s) Description 9 Endian Mode 0: 60x logic interprets data from 60x in Big Endian mode 1: 60x logic interprets data from 60x in Little Endian mode 10 Eieio Retry Disable 0: Device will always SYS_ARTRY an EIEIO operation until every command in 60x queues has been dispatched to the logic units inside device. 1: Device will not SYS_ARTRY an EIEIO operation 11 DBG Park Control 0: DBG signals are not parked when bus is idle 1: DBG signals are parked when bus is idle; mode to use for 0 wait state L2 look aside Bit 13 must be set to zero or this bit is ignored. 12 Reserved (must be left to zero) 13 Activate TA Signal Pre-charge 0: The TA signal is precharged by device after a data bus tenure 1: The TA signal is not precharged by device at the completion of a data bus tenure 14 Reserved. These bit should be left to zero. 15 Reserved. R/W 16 DBG Control 0: DBG0 and DBG1 signals are driven separately 1: DBG0 and DBG1 signals are effectively the same, they are logically ORed; mode to use for L2 lookaside 17 Reserved. R/W 18 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 105 of 209 IBM Dual Bridge and Memory Controller CPU Soft Reset Register (SRST) This register provides software with a mechanism to issue soft resets to each of the processors. When device detects a write to this register, the corresponding SRESET signal is driven active for a minimum of four bus clocks. Address x‘FF00 1040’ Access Type Write Only Soft Reset Control for ARB Level 1 x’0000 0000’ Soft Reset Control for ARB Level 0 Reset Value 0 1 Reserved 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 Soft Reset Control for ARB Level 0 0: Writing 0 to this bit has no effect 1: Writing 1 to this bit will initiate a pulse on the SYS_SRESET0 signal. 1 Soft Reset Control for ARB Level 1 0: Writing 0 to this bit has no effect 1: Writing 1 to this bit will initiate a pulse on the SYS_SRESET1 signal. 2 - 31 Reserved Page 106 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Error Control Register (ERRC) This register controls how the 60x interface logic responds when detecting an error. Reserved 0 1 2 3 Data Parity Checking Enable Read/Write Address Parity Checking Enable Access Type Disable Data Bus Timeout x‘FF00 1050’ No SYS_L2_HIT Signal Detected Error Disable Address Reserved x’0000 0000’ 60x Bus Configuration cycle Timeout Disable Reset Value Reserved 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-3 Description Reserved 4 60x Bus Configuration Cycle Timeout Disable 0: 60x logic will respond with x’F000 0000’ for a read from x’FF20 0000’ if SYS_L2_HIT signal not driven active 1: No configuration response performed 5 Reserved 6 No SYS_L2_HIT Signal Detected Error Disable 0: 60x logic will generate TEA on the system bus if SYS_L2_HIT signal not driven active after AACK 1: No action if SYS_L2_HIT detected inactive 7 Disable Data Bus Timeout 0: Device will signal error if 8ms time-out detected from DBG to TA 1: Device will not signal an error for this condition 8 Address Parity Checking Enable 0: 60x logic will not check address parity on the system bus 1: 60x logic will check address parity on the system bus 9 Data Parity Checking Enable 0: 60x logic will not check data parity on the system bus 1: 60x logic will check data parity on the system bus 10 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 107 of 209 IBM Dual Bridge and Memory Controller System Error Status Register (SESR) This register is the primary error status register for device and should be read first after a Machine Check interrupt occurs. All errors that result from CPU initiated transfers are logged in this register. Errors resulting from transfers initiated by a PCI Master or by the DMA controller will result in BITs 17, 18, or 19 being set and require software to interrogate additional error registers in the PCI bridge logic and the DMA controller logic. BIT 16, CPU to PCI Bus error, will also require software to interrogate additional error registers in the PCI bridge logic. 0 6 7 8 9 CPU Access to Memory Error (for CPU 1) DMA Error (for CPU 1) CPU to PCI Bus Access Error (for CPU 1) Addressing Error Detected (for CPU 1) CPU Access to Memory Error (for CPU 0) Data Bus Timeout Error DMA Error (for CPU 0) Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0-1 PCI-64 Bus Master Error 5 PCI-32 Bus Master Error 4 CPU to PCI Bus Access Error (for CPU 0) 3 Reserved Addressing Error Detected (for CPU 0) 2 1 Address Bus Parity Error Read/Write Access to Disabled System I/O Address Space Error Access Type DMA Controller Access Error x‘FF00 1060’ Flash Write Error Address Checkstop Error x’0000 0000’ Reserved Reset Value Data Bus Parity Error The bits 22, 23, 24, 25 that are available for read after a CPU1 Machine Check interrupt have the same meaning as errors reported on bits 15, 16, 19, 21 for CPU0. Software is responsible for writing zeros to this register in order to clear the bits that are set. Description Reserved 2 Checkstop Error 0: No Error 1: Device initiated checkstop occurred 3 Flash Write Error 0: No Error 1: Write to flash occurred when not enabled 4 DMA Controller Access Error 0: No Error 1: Access performed to DMA Controller when not enabled Page 108 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bit(s) 5 6 - 12 Description Access to Disabled System I/O Address Space Error 0: No Error 1: Access performed to System I/O address space that is not enabled Reserved 13 Address Bus Parity Error 0: No Error 1: 60x bus address parity error detected by device 14 Data Bus Parity Error 0: No Error 1: 60x bus data parity error detected by device 15 Addressing Error Detected (for CPU 0) 0: No Error 1: Addressing error 16 CPU to PCI Bus Access Error (for CPU 0) 0: No Error 1: Error occurred on PCI bus while servicing processor load/store request 17 PCI-32 Bus Master Error 0: No Error 1: Error occurred during PCI master initiated operation 18 PCI-64 Bus Master Error 0: No Error 1: Error occurred during PCI master initiated operation 19 DMA Error (for CPU 0) 0: No Error 1: Error occurred during DMA transfer 20 Data Bus Timeout Error 0: No Error 1: Device detected 8ms time-out between DBG to last SYS_TA or SYS_TEA 21 CPU Access to Memory Error (for CPU 0) 0: No Error 1: Error occurred during an access by the CPU to memory; Error logged in MESR and MEAR 22 Addressing Error Detected (FOR CPU 1) 0: No Error 1: Addressing error. 23 CPU to PCI Bus Access Error (for CPU 1) 0: No Error 1: Error occurred on PCI bus while servicing processor load/store request 24 DMA Error (for CPU 1) 0: No Error 1: Error occurred during DMA transfer 25 CPU Access to Memory Error (for CPU 1) 0: No Error 1: Error occurred during an access by the CPU to memory; 26 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 109 of 209 IBM Dual Bridge and Memory Controller System Error Address Register (SEAR) This register contains the CPU address associated with the error that is logged in the SESR register described previously. This register is only updated for errors that are due to CPU initiated transfers. The address for errors that result from transfers initiated by PCI masters or DMA controller are located in error registers contained in the PCI bridge logic or the DMA controller logic. In the case of dual-processor implementation, this register will contain only the address of the first error detected. Reset Value x’0000 0000’ Address x‘FF00 1070’ Access Type Read/Write Address Associated with Error Contained in SESR 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description Address Associated with Error Contained in SESR Page 110 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Chip Programmability Register (PGCHP) 2 3 4 5 6 7 Bit(s) 0 1 2-7 SYS_TEA Control Disable PowerPC Processor Type 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Reserved SYS_ARTRY Enable 9 Reserved 8 Reserved Reserved - left to 0 1 Local Reset Enable 0 Reserved TRAS4 (Active for SDRAM access only) Read/Write Reserved - left to 0 Access Type External Arbiter on PCI-64 Enable x‘FF00 1100’ PCI-64 Host Bridge Address Map Type Address Reserved - left to 0 x’0000 0000’ PCI-32 Host Bridge Address Map Type Reset Value Machine Check Detected Signal When Single Bit Error This register allows the device to be programmed in order to provide additional functions. Reserved Description PCI-32 Host Bridge Address Map Type. Controls which address map is used. See Address Maps on page 143. 0: PREP mode 1: FPHB mode (Specific Base address on PCI-32 is used) Reserved. Must be left to 0. Reserved 8 PCI-64 Host Bridge Address Map Type. Controls which address map is used. See PCI to System Memory Addressing Model (FPHB Mode) on page 148 0: PREP mode 1: FPHB mode (Specific Base address on PCI-64 is used) 9 External Arbiter on PCI-64 Enable. Read only status bit. 0: Internal arbiter is activated 1: Internal arbiter is deactivated 10 Reserved. Must be left to 0. 11 Local Reset Enable 0: PCI-64 Signal G_RESETOUT is not driven 1: If external arbiter then G_RESETOUT is driven. 12 - 15 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 111 of 209 IBM Dual Bridge and Memory Controller Bit(s) Description 16 Reserved. R/W - Must be left to 0 17 Machine Check Detected Signal When Single Bit Error 0: SYS_MACHK signal not driven 1: SYS_MACHK signal is driven 18 TRAS4 (Active for SDRAM access only) 0: tRASmin = 5 * clock 1: tRASmin = 4 * clock 19 Reserved 20 - 23 Reserved. R/W 24 Auto Retry Enable 0: SYS_ARTRY is not driven 1: SYS_ARTRY is driven when the access is in Peripheral Memory or I/O space with potential deadlock 25 PowerPC Processor Type (see Address Transfer Attribute for Snoop Register (ATAS) on page 118). 0: 604 1: 750 or later version 26 TEA Control Disable 0: SYS_TEA is driven 1: SYS_TEA is not driven but Machine Check Signal is. 27 - 31 Reserved Page 112 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Free Register 1 (RGBAN1) This register contains Data coming from the CPU. Reset Value x’0000 0000’ Address x‘FF00 1110’ Access Type Read/Write Data from CPU 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description Data from CPU CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 113 of 209 IBM Dual Bridge and Memory Controller Free Register 2 (RGBAN2) This register contains Data coming from the CPU. Reset Value x’0000 0000 Address x‘FF00 1120’ Access Type Read/Write Data from CPU 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description Data from CPU Page 114 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller GPIO Direction Register (GPDIR) This register sets the direction of signals (input or output) on pins GPIO[0:2]. x’0000 0000 Address x‘FF00 1130’ Access Type Read/Write GPIO Pin Direction from 0 to 2 Reset Value 0 1 Reserved 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description0 0-2 GPIO Pin Direction from 0 to 2 0: Input 1: Output 3 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 115 of 209 IBM Dual Bridge and Memory Controller GPIO Input Value Register (GPIN) This register stores values of the signal on pins GPIO[0:2] if it is defined as input. x’0000 0000 Address x‘FF00 1140’ Access Type Read Only GPIO Input PIN Value from 0 to 2 Reset Value 0 1 Reserved 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-2 GPIO Input Pin Value from 0 to 2 3 - 31 Reserved Page 116 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller GPIO Output Value Register (GPOUT) This register stores values of signal on pins GPIO[0:2] if defined as output. x’0000 0000 Address x‘FF00 1150’ Access Type Read/Write GPIO Output Pin Value from 0 to 2 Reset Value 0 1 Reserved 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-2 GPIO Output Pin Value from 0 to 2 3 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 117 of 209 IBM Dual Bridge and Memory Controller Address Transfer Attribute for Snoop Register (ATAS) This register contains SYS_TT, SYS_TSIZ and SYS_TBST values that are used during a snoop transaction. These values can be changed according to the type of PowerPC processor. This register must be set if bit 25 of the PGCHP register is programmed to 1. See Chip Programmability Register (PGCHP) on page 111. Reset Value x’0000 0000’ Address x‘FF00 1160’ Access Type Read/Write Programming Value x’709C 2508’ b’0111 0000 1001 1100 0010 0101 0000 1000’ 1 2 3 4 5 6 7 Reserved SYS_TBST Value for clean operation SYS_TSIZ[0:2] Values for clean operation SYS_TT[0:4] Values for clean operatio Description 0-4 SYS_TT[0:4] Values for flush operation 5 -7 SYS_TSIZ[0:2] Values for flush operation 8 SYS_TBST Value for flush operation 9 Reserved 10 - 14 SYS_TT[0:4] Values for kill operation 15 - 17 SYS_TSIZ[0:2] Values for kill operation 18 SYS_TBST Value for kill operation 19 Reserved 20 - 24 SYS_TT[0:4] Values for clean operation 25 - 27 SYS_TSIZ[0:2] Values for clean operation 29 - 31 Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 28 SYS_TBST Value for kill operation 9 SYS_TSIZ[0:2] Values for kill operation 8 SYS_TT[0:4] Values for kill operation Reserved 0 SYS_TBST Value for flush operation SYS_TT[0:4] Values for flush operation SYS_TSIZ[0:2] Values for flush operation This setting is recommended for the PowerPC750 which isnot able to perform Cache/memory coherency with Kill and Flush operation as the PowerPC 604. SYS_TBST Value for clean operation Reserved Page 118 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Reserved Reserved 2 PCI-64 DEVCNT 1 PCI-64 Target Abort 0 PCI-64 Master Abort Reserved PCI-64 Counter Disable Read/Write PCI-32 Access Completion Access Type PCI-32 DEVCNT x‘FF00 1170’ PCI-32 Target Abort Address PCI-32 Master Abort x’0000 0000’ PCI-32 Counter Disable Reset Value PCI-64 Access Completion Diagnostic Register (AVDG) Reserved Description 0 PCI-32 Counter Disable 0: TRDY, IRDY, DISCNT Counters are not activated (The MSB is always at 1) (The DISCNT counter is programmable - see Disconnect Counter (DISCNT) on page 57) 1: TRDY, IRDY, DISCNT Counters are ACTIVATED 1 PCI-32 Master Abort 0: Window of Master Abort is reduced to one cycle (avoid parasitic master abort detection) 1: Window of Master Abort is not reduced 2 PCI-32 Target Abort 0: Device detects Target abort (The Frame output is taken) 1: Device never detects Target Abort but retry indefinitely accesses 3 PCI-32 DEVCNT 0: Stop the counter down when devsel is detected 1: Do not stop the counter down 4 PCI-32 Access Completion 0: The completion is activated when device is master and not during external exchange 1: The completion appears when the data is not the last one. 5-7 Reserved 8 PCI-64 Counter Disable 0: TRD0Y, IRDY, DISCNT Counters are not activated (the MSB is always at 1) DISCNT counter is programmable see Disconnect Counter (DISCNT) on page 57 1: They are ACTIVATED 9 PCI-64 Master Abort 0: Window of Master Abort is reduced to one cycle (avoid parasitic master abort detection) 1: Window of Master Abort is not reduced 10 PCI-64 Target Abort 0: Device detects Target abort (The Frame output is taken) 1: Device never detects Target Abort but retry indefinitely accesses CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 119 of 209 IBM Dual Bridge and Memory Controller Bit(s) Description 11 PCI-64 DEVCNT 0: Stop the counter down when devsel is detected 1: No stop the counter down 12 PCI-64 Access Completion 0: The completion is activated when device is master and not during external exchange 1: The completion appears when the data is not a last. 13 - 15 16 17 - 31 Reserved Reserved - Must be left to 0 Reserved Page 120 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Memory Controller Control Register (MCCR) This register provides the primary control for the memory controller logic. Reset Value x’0000 0000’ Address x‘FF00 1200’ Access Type Read/Write Bit(s) Description 0 Global System Memory Address Space Enable 0: Device will not respond to addresses specified in Memory Configuration Extent Register (MCERx) 1: System memory address space enabled. 1 Diagnostic Mode 0: Normal Mode: Multi-bit ECC error will generate Machine Check 1: Diagnostic Mode: Multi-bit ECC does NOT generate Machine Check; logged in MEAR & MESR 2 SDRAM Initialization Status (read-only) 0: SDRAM initialization is not completed. 1: SDRAM initialization is completed. 3-4 ECC Mode 00: Normal generation and checking of ECC codes 01: ECC check disabled; Byte lane 0 routed to/from ECC check field. Data byte 0 forced to all zeros 10: ECC check disabled; Normal routing of data and normal ECC code generation 11: Reserved 5-7 Row Cycle Time for SDRAM Auto-refresh (tRC) 000: 5 bus cycles 001: 6 bus cycles 010: 7 bus cycles 011: 8 bus cycles 100: 9 bus cycles 101: 10 bus cycles 110: 11 bus cycles 111: 12 bus cycles 8-9 DRAM Type Must be set to 10 for SDRAM 10 11 Data Pacing Mode (Must be set to 1 for SDRAM) Data Mask Mode (SDRAM only) 0: 16 SDCS are available. DQM pin of SDRAM devices must be grounded. 1: Only eight SDCS are available. DQM signal is present on the eight other pins. Activate to prevent tRDL violation during “Write interrupted by pre-charge” operations if the device does not guarantee that the data presented in the same time as pre-charge is not properly ignored. 12 - 15 Reserved. Must be left to 0 16 Reserved. Must be set to 0 17 Reserved. Must be set to 1 18 Reserved. Must be set to 1 19 Reserved. Must be set to 0 20 Reserved. Must be set to 0 CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 121 of 209 IBM Dual Bridge and Memory Controller Bit(s) 21 - 22 23 24 - 29 Description Reserved. Must be set to b’00’ Reserved. Must be set to 0 Reserved 30 Disable Page Mode 0: Memory controller will perform fast page accesses for back to back operations if appropriate 1: Memory controller will perform fast page access only within a burst operation. It will NOT perform fast page accesses for back to back bursts even if they occur to the same RAS page. 31 Disable Queue Same Page Override 0: Memory queue ordering can be overridden if an operation is to the same page. 1: Memory queue always processed in order received. Page 122 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Memory Error Status Register (MESR) Access Type Read/Write Overlapped Memory Extents x‘FF00 1220’ Address Error Flag Address Single Bit Error Flag x’0000 0000’ Double Bit Error Flag Reset Value 0 1 2 3 Single or Double Bit Error Syndrome This register provides error status information on memory errors. In order to log additional errors, software must clear the register by writing zeros throughout. Reserved 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 Double Bit Error Flag 0: No Error 1: Double Bit ECC error occurred 1 Single Bit Error Flag 0: No Error 1: Single bit ECC error occurred 2 Address Error Flag 0: No Error 1: Address error occurred 3 Overlapped Memory Extents 0: No Error 1: An access occurred to an address that is mapped in two different memory configuration extents. 4 - 23 Reserved 24 - 31 Single or Double Bit Error Syndrome. Used to determine the failing DIMM CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 123 of 209 IBM Dual Bridge and Memory Controller Memory Error Address Register (MEAR) This register contains the address associated with the error logged in the MESR. Reset Value x’0000 0000’ Address x‘FF00 1230’ Access Type Read/Write Address of Memory Error 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description Address of Memory Error Page 124 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Memory Configuration Extent Registers (MCER[0:7]) Each one of the eight registers MCER0 to MCER7 defines one of up to eight banks of memory (Bank 0 to 7) supported. All registers have the same definition, and each defines the size and location for the particular bank of memory. x’0000 0000’ Address MCER0 MCER1 MCER2 MCER3 MCER4 MCER5 MCER6 MCER7 Access Type Read/Write 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 Extent Size Code For Bank Reserved 0 Start Address For Bank SDRAM Addressing Organization (SDRAM Only) Reserved x‘FF00 1300’ x‘FF00 1310’ x‘FF00 1320’ x‘FF00 1330’ x‘FF00 1340’ x‘FF00 1350’ x‘FF00 1360’ x‘FF00 1370’ Reserved Bank Enable Reset Value Description Bank Enable 0: Bank is not present or register initialization is not complete 1: Bank is present and decoded by device 1-3 Reserved. R/W 4 - 14 Start Address For Bank. (Bits 0 - 10) - Defines the beginning address of this bank. Contains bits 0 - 10 of the 32-bit real address. Address restricted to a boundary equal to the size of the bank. 15 Reserved. R/W CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 125 of 209 IBM Dual Bridge and Memory Controller Bit(s) Description 16 - 25 Extent Size Code For Bank x’3FF’ Reserved x’3FB’ Reserved x’3F3’ 4 MB x’3E3’ 8 MB x’3C3’ 16 MB x’383’ 32 MB x’303’ 64 MB x’203’ 128 MB x’003’ 256 MB x’002’ 512 MB x‘000’ 1 GB 26 - 29 SDRAM Addressing Organization b’0001’: 11/ 8/2 (Row/Col/Bank) b’0010’: 11/ 9/1 b’0011’: 11/10/1 b’0100’: 12/ 8/2 b’0101’: 12/10/2 b’0110’: 13/ 8/1 b’0111’: 13/ 8/2 b’1000’: 13/ 9/1 b’1001’: 13/10/1 b’1010’: 11/ 8/1 b’1011’: 12/ 8/1 b’1100’: 12/9/1 b’0000’: All other supported organizations 30 - 31 Reserved Page 126 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System I/O Register 0 (SIOR0) This register is user defined. However it has been introduced in the PowerPC chip support to provide the memory DIMM presence detect pins for all four pairs of DIMM sockets. Device supports a maximum of four pairs, or eight DIMMs. The DIMM pairs must be of exactly the same type and therefore only one DIMM presence detect pin of each pair are read in from this register. The read of this register results in the assertion of the PRES_OE0 signal and a Read cycle through the PCI32 A/D lines. That permits a read of the outside buffers containing the presence detect bits. Bit 0 of this register correspond to bit 31 on the PCI A/D lines. Reset Value x’0000 0000’ Address x‘FF00 1400’ Access Type Read Only User Defined 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 31 User-defined Example of usage: DIMM Pair 0 Presence Detect Pins 0 1 2 3 4 5 6 DIMM Pair 1 Presence Detect Pins 7 8 9 DIMM Pair 2 Presence Detect Pins DIMM Pair 3 Presence Detect Pins 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-7 DIMM Pair 0 Presence Detect Pins: PD1-PD8 8 - 15 DIMM Pair 1 Presence Detect Pins: PD1-PD8 16 - 23 DIMM Pair 2 Presence Detect Pins: PD1-PD8 24 - 31 DIMM Pair 3 Presence Detect Pins: PD1-PD8 Please see MCER Register Initialization on page 180 for PD definition and device supported values. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 127 of 209 IBM Dual Bridge and Memory Controller System I/O Register 1 (SIOR1) Address x‘FF00 1420’ Access Type Read Only User Defined 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description User-defined The read of this register results in the assertion of the PRES_OE1 signal and a Read cycle through the PCI32 A/D lines. That permits a read of the outside buffers containing the presence detect bits. Bit 0 of this register correspond to bit 31 on the PCI A/D lines. Page 128 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller DMA Registers Space DMA Global Control (GSCR) Reset Value x’0000 0000’ Address User Privileged x‘FF1C 0020‘ x‘FF1E 0020’ Access Type User Privileged Read Only Read/Write Bit(s) 0-1 Description DMA Transfer Enable 00: Reset DMA Controller to default power up mode. 10: DMA Controller disabled 11: DMA Controller is enabled 2 Reserved. R/W 3 Interrupt Enable When set, generates an interrupt at the completion of a DMA transfer 0: IT2 disabled 1: IT2 enabled 4 Interrupt Status 0: End of DMA transfer interrupt IT2 not asserted 1: End of DMA transfer interrupt IT2 asserted Software must write a 0 to Reset the IT2 Interrupt 5 Extended DMA Transfer Enable 0: Single DMA transfer 1: Extended DMA 6 Direction for Extended DMA 0: PCI to MEMORY (’ECOWX’) 1: MEMORY to PCI (’ECIWX’) 7 Reserved. R/W - Must be left to 0 8 - 15 Reserved. RO 16 - 31 Number of DMA Transfer Loops to Do (if Extended DMA is enabled). During an Extended DMA, contains the number of loops remaining. If bit 5 is enabled and this register is set to 0, the mode is a single DMA transfer. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 129 of 209 IBM Dual Bridge and Memory Controller DMA Global Status (GSSR) x’0000 0000 Address User Privileged x‘FF1C 0030‘ x‘FF1E 0030‘ Access Type User Privileged Read Only Read Only DMA Transfer Abort Reset Value 0 Reserved 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 1 - 31 Description DMA Transfer Aborted 0: No Error 1: DMA transfer aborted Reserved Page 130 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller DMA Transfer Control (XSCR) Reset Value x’0000 0000’ Address User Privileged Access Type Read/Write (User and Privileged) 0 1 2 3 4 5 6 7 8 9 Byte Offset Address Increment Reserved Reserved Transfer Length Global Transfer Reserved x‘FF1C 0040’ x‘FF1E 0040‘ Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-2 Reserved 3 - 15 Transfer Length. Contains the number of bytes to be transferred (max is 4 K). A value of 0 will transfer 0 bytes. 16 - 20 Reserved 21 Global Transfer 0: No snoop operations required for accesses to system memory 1: Accesses to system must be coherent 22 Reserved 23 Address Increment 0: Do NOT increment I/O address during DMA transfer 1: Increment I/O address during DMA transfer 24 - 29 Reserved 30 - 31 Byte Offset. Specifies the byte offset associated with the DMA transfer real address CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 131 of 209 IBM Dual Bridge and Memory Controller DMA Transfer Status (XSSR) Reset Value x’0000 0000’ Address User Privileged Access Type Read Only (User and Privileged) 0 1 2 3 4 5 6 7 8 9 Address Increment Alignment Error TLBSYNC Detected Page Crossing Error Unaligned Transfer Error Unaligned ECOWX/ECIWX Address Error Transfer Halted Transfer Status Transfer Complete ECC Error Address Error Reserved PCI Bus Error Transfer Length Invalid PCI Address Reserved x‘FF1C 0050’ x‘FF1E 0050’ 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-2 Reserved 3 - 15 Transfer Length. Contains the number of bytes remaining when the transfer was completed or aborted. 16 - 19 Reserved 20 Invalid PCI Address 1: XPAR did not match any PCI extents 21 PCI Bus Error 1: Error detected during PCI bus transaction. No Interrupt generated, only MACHK (Machine Check Signal) is activated. 22 Address Error 1: Invalid memory address detected (no Interrupt generated, only MACHK is activated) 23 ECC Error 1: Double-bit ECC error detected in memory (no Interrupt gen., only MACHK is activated) 24 Transfer Complete 0: Transfer is not complete 1: Transfer is complete for Memory Interface 25 Transfer Status 0: No DMA transfer in progress 1: DMA transfer operation is underway 26 Transfer Halted 1: DMA transfer operation in progress was halted due to start of second DMA transfer operation 27 Unaligned ECOWX/ECIWX Address Error 1: Address associated with ECOWX/ECIWX is not word aligned Page 132 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bit(s) Description 28 Unaligned Transfer Error 1: Address alignment error 29 Page Crossing Error 1: Page Crossing detected during DMA transfer 30 TLBSYNC Detected 0: No TLBSYNC Detected 1: TLBSYNC detected during DMA transfer Transfer 31 Address Increment Alignment Error 1: Improper alignment of addresses when Address Increment bit is off CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 133 of 209 IBM Dual Bridge and Memory Controller DMA Transfer PCI Address (XPAR) Reset Value x’0000 0000’ Address User Privileged x‘FF1C 0070‘ x‘FF1E 0070‘ Access Type User Privileged Read Only, Read/Write Read/Write, Read Only PCI Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 - 31 Description PCI Address. Contains the adapter I/O address for the DMA transfer operation. Page 134 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller DMA Transfer Write Back Address (XWAR) Reset Value x’0000 0000’ Address User Privileged x‘FF1C 0090’ x‘FF1E 0090’ Access Type User Privileged Read Only Read/Write Bit(s) Description 0 - 25 Writeback Address. Contains the real address used by the device at the end of the DMA transfer operation to which the completion status is written. 26 - 31 Reserved (assumed to be zero). CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 135 of 209 IBM Dual Bridge and Memory Controller DMA Transfer Translated Address (XTAR) Reset Value x’0000 0000’ Address User Privileged Access Type Read Only (User and Privileged) x‘FF1C 00A0‘ x‘FF1E 00A0‘ Translated Address 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 31 Translated Address. Contains the 32-bit real address presented on the processor bus during the ecowx/eciwx transfer. Page 136 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System Standard Configuration Registers Space The registers listed in this section can only be accessed from the PowerPC processor. Access through the 60x bus directed to the specific PCI bridge permits the PCI configuration. Both PCI bridges inside device must be configured before any PCI configuration cycles can be issued. The primary purpose of these registers is to provide a mechanism for firmware to identify the PCI bridge and the DCR and DID registers, and to assign a 1 MB address space in the system memory map for the location of the PCI bridge facilities (BAR register). Device Characteristics Register (DCR) Access Type Read Only 0 1 2 3 4 Reserved Device Type 5 6 7 8 9 Reserved Reserved x‘FF20 0000’ Address Increment Address Memory Allocation Indicator for Control Space x’3010 0000’ BUID Allocation Indicator Reset Value Feature/vpd ROM Size Characteristics This register identifies the type of device present. 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0-3 Device Type 0011: I/O device 4-5 BUID Allocation Indicator 00: NO BUID Required 6-7 Reserved 8 - 11 Memory Allocation Indicator for Control Space 0001: 1 MB 12 - 24 Reserved 25 - 26 Feature/vpd ROM Size Characteristics 00: No Feature/VPD ROM present 27 - 29 Address Increment 000: 4-byte Increment 30 - 31 Reserved CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 137 of 209 IBM Dual Bridge and Memory Controller Device ID Register (DID) This register provides specific device type information. x’08020 1100’ Address x‘FF20 0004’ Access Type Read Only IBM Device Reset Value 0 Reserved 1 2 3 4 5 Device ID Type Field 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 Specific Device ID Description IBM Device 1: IBM Device 1-7 Reserved 8 - 23 Device ID Type Field: x’2011’: Device PCI Bridge 24 - 31 Specific Device ID: x’00’: PCI-32 bridge x’01’: PCI-64 bridge Page 138 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Base Address Register (BAR) This register is written by software to indicate to the PCI bridge where its register space is located in the 4 GB system addressing space. There are no restrictions placed on the value of this register other than it must not overlap other extents defined for the system. Reset Value x’0000 0000 Address x‘FF20 0018’ Access Type Read/Write Upper Bits of 1MB Address-Bridge Register Space 0 1 2 3 4 5 6 7 8 9 Reserved 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) Description 0 - 11 Upper Bits of 1 MB Address for Bridge Register Space 12 - 31 Reserved. (Assumed to be X’0 0000’) Note: The start address is assumed to be on a 1 MB boundary. CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 139 of 209 IBM Dual Bridge and Memory Controller Device Specific Configuration Space The registers listed in this section can only be accessed with configuration cycles on the 60x bus directed to the specific PCI bridge. PCI BAR Enable Register (PCIENB) This register provides a mechanism for software to disable the PCI bridge logic from decoding the address space pointed to by the BAR. This register is primarily used at power on time when the BAR has not been initialized. x’0000 0000’ Address x‘FF20 1000’ Access Type Read/Write Enable PCI Control Space Reset Value Reserved 0 1 2 3 Reserved 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 Bit(s) 0 Description Enable PCI Control Space 0: PCI Bridge only responds to configuration cycles 1: PCI Bridge responds to address space specified in the BAR register 1-3 Reserved 4 - 31 Reserved Page 140 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller CPC710_Regs.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 141 of 209 IBM Dual Bridge and Memory Controller Page 142 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Regs.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Addressing Model Address Maps Device address spaces can be programmed using the PowerPC REference Platform specification (PREP) Mode. Also a highly Flexible PCI Host Bridge (FPHB) Mode is available.The address map is highly programmable in either mode. The following restrictions must be observed when programming the device: • The upper 16 MB is reserved for ROM, system configuration, DMA controller, etc. See System Space Address Map (x‘FF00 0000’ to x‘FFFF FFFF’) on page 34 for the definition of this address space. Only PCI Memory spaces are allowed to overlap this area, however, they are not forwarded to the PCI bus. • At least 1MB of system memory must be available at address 0. Minimum granularity of DIMMs is 16MB. • System memory cannot be located above 2GB. • Avoid overlapping system memory extents with PCI extents. Hang conditions and unpredictable results can occur if a processor accesses an address contained in two different extents. Memory Map 16 MB range not forwarded to PCI bus 4GB 16 MB Area to map PCI Memory Spaces 2GB Area to map PCI I/O spaces Area to map System Memory 16 MB 0 CPC710_Map.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 143 of 209 IBM Dual Bridge and Memory Controller CPU to PCI Addressing Model PREP and FPHB Modes Programmable registers in the Specific PCI Host Bridge Space (Specific PCI Host Bridges Space (BAR + x‘000F 6110’ to BAR +x‘000F 9810’) on page 34) map PCI Memory and PCI I/O address spaces into the 4 GB System address space. Each PCI bridge in the device contains a set of these registers, allowing firmware to program PCI address spaces anywhere in memory rather than at fixed PCI address spaces. For example, the registers can be configured to have PCI address spaces in system memory follow the fixed Sandalfoot PCI addressing model. CPU to PCI Addressing Model (PREP and FPHB Modes) Processor View PCI I/O Space PCI Memory Space 4GB 4GB-16MB Programmable Registers MSIZE Peripheral Memory Space SMBAR PCI Memory PMBAR IOSIZE Peripheral I/O Space SIBAR PCI I/O PIBAR 16MB 0 As the figure above shows, the device monitors addresses on the processor bus to determine whether a CPU address falls within the ranges specified by the following SMBAR/MSIZE and SIBAR/IOSIZE registers: • PCI Memory Address Space Size (MSIZE) on page 73 • System Base Address for PCI Memory (SMBAR) on page 75 • PCI I/O Address Space Size (IOSIZE) on page 74 • System Base Address for PCI I/O (SIBAR) on page 76 If the address falls within one of these ranges, the 60x interface logic passes the address and command to the appropriate PCI bridge logic for execution using the translation specified by the following PMBAR or PIBAR registers: • PCI Base Address for I/O (PIBAR) on page 67 • PCI Base Address for Memory (PMBAR) on page 68 Page 144 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Map.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Peripheral I/O Address Translation The first 8MB of Peripheral I/O space requires additional translation. To prevent 32-byte granularity accesses to ISA addresses, the device supports a noncontiguous I/O address mode in which the first 64KB of PCI bus I/O space is divided into 32byte segments spaced at 4K intervals within system memory. This mode is selected by bit 5 of PHB Configuration Register (CTLRW) on page 77). Noncontiguous I/O Address Mode Enabled Peripheral I/O Space - 8MB SIBAR + 8MB Area Wrapped To First 32 Bytes 32 Bytes IOSIZE PCI I/O PIBAR + 8 MB IOSIZE SIBAR + 12 KB 32 Bytes Area Wrapped To First 32 Bytes Not addressable SIBAR + 8 KB 32 Bytes Area Wrapped To First 32 Bytes SIBAR + 4 KB 32 Bytes Area Wrapped To First 32 Bytes 32 Bytes SIBAR PIBAR + 64 KB 32 Bytes 32 Bytes 32 Bytes 32 Bytes 32 Bytes CPC710_Map.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 PIBAR Page 145 of 209 IBM Dual Bridge and Memory Controller PCI to System Memory Two types of address mapping modes are available: PowerPC Reference Platform (PREP) Mode and Flexible PCI Host Bridge (FPHB) Mode. To select a mode, program bit 0 (for PCI-32) or bit 8 (for PCI-64) in the Chip Programmability Register (PGCHP) on page 111. PowerPC Reference Platform (PREP) Mode In PREP Mode, access from the PCI to the system can be performed with or without PCI address translation. When translation is used, the most common method is to translate addresses by complementing the upper 12 bits. PCI addresses ranging from x’8000 0000’ to x’FFFF FFFF’ are translated to system memory addresses x’0000 0000’ to x’7FFF FFFF’. In this mode only PCI access to Memory are decoded by the CPC710 ; Configuration and I/O are not decoded. PCI Master Address Operation Whenever the PCI bridge logic identifies addresses coming from ISA Masters (when the P_ISA_MASTER signal is active =1), they are passed directly to system memory. Otherwise, the untranslated addresses are checked to determine whether they fall within a bridge’s PCI memory address range by comparing the PCI address to the following registers: • PCI Base Address for Memory (PMBAR) on page 68 • PCI Memory Address Space Size (MSIZE) on page 73 If there is no match and if translation is enabled by software, the PCI address is translated to a system address (bit 4 - Personalization Register (PR) on page 70). A series of checks is performed to determine whether the access is back to the same bridge. If it is, the PCI bridge will not respond to the PCI master. The PCI bridge logic also forwards the access to system memory. If this address does not match a memory configuration extent, the memory controller logic returns an invalid address error, thus ensuring that PCI masters do not access system facilities. Page 146 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Map.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Translation Enabled If translation is enabled, the PCI bridge logic translates addresses before presenting them to system memory, as shown in the following figure. However, not all addresses are presented. System Memory Space Translation PCI Memory Space 4GB Complement Upper Address bit(0) 2GB Complement Upper 12 Address Bits No Translation Not Forwarded MSIZE PCI Memory PMBAR Complement Upper 12 Address Bits 0 Translation Disabled If translation is disabled, the PCI bridge does not translate addresses before presenting them to the system, as shown in the following figure. System Memory Space PCI Memory Space 4GB No Translation Not Forwarded to System MSIZE PCI Memory PMBAR 0 Note: Translation can be disabled for CPU-to-PCI transfers if the values stored in the PMBAR and SMBAR registers are the same. CPC710_Map.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 147 of 209 IBM Dual Bridge and Memory Controller Flexible PCI Host Bridge (FPHB) Mode In FPHB Mode, External Masters on the 32-bit and 64-bit PCI buses address system memory using the address translation model shown in the following figure. The model uses several programmable registers in the Specific PCI Host Bridge Space (Specific PCI Host Bridge Registers on page 63). Note: Each PCI bridge contains a set of programmable registers. Note: This flexible FPHB mode allows the configuration by an external PCI agent of some of the CPC710 registers of the PCI 64 bus bridge such as the PSBAR, PSEM, IT_ADD_SET and INT_RESET registers. See Standard PCI Configuration Space ( register x‘00’ to x‘68’ ) on page 34. The device monitors addresses on the PCI bus to determine whether a PCI address falls within the range specified by the following PSBAR/PSSIZE registers: • System Base Address Register for PCI-32 (PSBAR) on page 84 • System Address Space SIZE for PCI (PSSIZE) on page 81 If an address falls within this range, the PCI interface logic passes the address to the 60x bridge logic for execution using the translation specified by the System Base Address Register (BARPS) on page 83. PCI to System Memory Addressing Model (FPHB Mode) System Memory Space PCI Space 4GB (*)Memory or I/O Space is selected by bit 7 of PSSIZE System Memory Programmable Registers BARPS PCI Memory or PCI I/O (*) PSSIZE PSBAR 0 Page 148 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Map.fm.01 11/4/1999 IBM Preliminary Draft IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller 60x Interface Overview The 60x interface ties the device to the 60x system bus. It performs the following: • • • • • • • • Arbitration Configuration Processor load/store address decoding PCI to Memory access Snoop operations Sync/EIEIO processing Endian translation Reset logic operations Time base functions Endian Support The device supports PowerPC 604, and 750 processors operating in Big Endian (BE) and Little Endian (LE) modes. The mode determines the order in which a multibyte scalar is stored in memory or I/O. In BE mode, the specified address contains the scalar’s most significant byte (MSB), the next sequential address contains the second MSB, and so on. In LE mode, the specified address contains the scalar’s least significant byte (LSB), the next sequential address contains the second LSB, and so on. Processor Behavior in LE Mode PowerPC 604 and 750 processors normally operate in BE mode. To operate in LE mode, the processors generate an LE address internally and then modify, or “munge,” the three low-order address bits to create a BE address equivalent. The processors do not issue unaligned LE transfers on the bus. Instead, they take an alignment interrupt. However, the PowerPC 604+ processor does issue unaligned LE transfers as long as they do not cross word boundaries. The following table describes the addresses generated by the processor for LE transfers. Endian Behavior PREP architecture requires data to be stored in the same Endian mode as the processor. Therefore, the device implements logic to “unmunge” the address and byte swap the data bus as it comes from the processor before sending it to memory or to the PCI bridges. See Device Endian Logic below. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 149 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Processor Little Endian Address Modification Transfer Size (bytes) Processor’s Internally Generated LE Effective Address [29:31] 1 0 7 6 53 1 6 53 43 2 5 4 3 4 4 3 2 13 5 2 13 03 6 1 0 7 0 31 2 52 4 62 72 8 Resulting Processor Big-endian Address [29:31] 4 0 0 1. The PowerPC 604+ does not support 3-byte transfers in LE mode, however, these transfer sizes will result from an unaligned 4byte access to an odd address 2. These transfer sizes are not supported by any of the processors. 3. These cells apply only to the PowerPC 604+ which performs unaligned LE transfers. Device Endian Logic PowerPC CPU Address 60x BUS Big and Little Endian Data PCI-64 Bridge Logic Unmunge and Byte Swap (Little Endian On) Big Endian Memory 64 Bytes Data Buffers Byte Swap Memory Control 64 Data PCI-64 BUS PCI-32 Bridge Logic Byte Swap Address 64 Bytes Buffer 64 Bytes Buffer 32 Bytes Buffer PCI-32 BUS SIO ROM Little Endian IBM25CPC710AB3A100 Page 150 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft PowerPC in Big Endian; Byte Swapping [0:7]bit Processor (Big Endian; MSB is bit 0) Memory (Big Endian) PCI-32 (Little Endian; MSB is bit 31) [8:15] [16:23] [24:31] [32:39] [40:47] [48:55] [56:63] 0 Byte 1 2 3 4 5 6 7 0 1 2 3 4 5 6 7 3 2 [31:24]bit 1 [23:16] 0 [15:8] Note: Byte order is depicted as Big Endian [7:0] Because the device cannot determine the processor’s Endian state, software must write to the Arbiter Control Register (bit 9) at the same time the processor HID register bit is updated. If the processor is operating in BE mode, bit 9 must be set to 0 to prevent the device from unmunging or byte swapping the processor’s data. If the processor is operating in LE mode, bit 9 must be set to 1 to unmunge the address as specified in Little Endian Address Unmunge Equations below, and to swap the data bus bytes as specified in Data Bus Byte Swap for Little Endian below. Little Endian Address Unmunge Equations Transfer Size Equation to Convert to Address 1 Byte ADDR[29:31] XOR ‘111’ 2 Byte ADDR[29:31] XOR ‘110’ and ‘1(31)1’ 3 Byte ADDR[29:31] XOR ‘101’ 4 Byte ADDR[29:31] XOR ‘100’ 8 Byte none Data Bus Byte Swap for Little Endian Byte 0 Byte 1 A 60x Data Bus 0 B 78 Byte 0 0 15 16 CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 23 24 F E 23 24 Byte 5 E 31 Byte 3 15 16 Byte 4 D Byte 2 G 78 Byte 3 C Byte 1 H Internal Data Bus Byte 2 0 F 78 Byte 4 0 H 23 24 Byte 6 C 78 Byte 7 G 15 16 Byte 5 D 31 Byte 6 Byte 7 B 15 16 31 A 23 24 31 Page 151 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft 60x Bus Arbiter Description The arbiter in the device has the following characteristics: • Arbitration for three devices; two levels for external masters and one for internal device requests • No half-cycle precharge required for SYS_TA, SYS_TEA, ABB, and DBB • Highly programmable address pipeline control • Data streaming capability for external devices • Programmable address bus parking capability • Programmable timing on SYS_AACK • Rotating address bus request priority scheme Rotating Priority Resolution The device’s 60x arbiter implements an algorithm that rotates priorities when the address bus is granted to a master. When multiple masters request the bus, the arbiter grants the bus to the master with the highest priority during the arbitration period, then downgrades that priority to the lowest level for the next period. The arbitration period occurs during the SYS_AACK assertion cycle. If two masters continuously request the bus, they receive alternate control. This logic is satisfactory unless a master implements a 64-byte cache line and needs to issue two 32-byte burst transfers to fill the cache. In this case, the device has a programmable mode whereby the arbiter allows one bus master to perform a pair of back-to-back address tenures even if another master requests the bus. This mode allows the device’s memory controller to remain in page mode for these accesses. Without this mode, another master could insert a memory transaction to take the memory controller out of page mode. Address Bus Pipelining Pipelining is controlled by bits 0 and 1 of the 60x Arbitration Control register (ABCNTL). Bit Description ‘10’ 0-1 ‘01‘ ‘00’ ‘11’ If enabled by software, the arbiter maintains up to a two level pipeline per master . The arbiter continues to grant the address bus to a specific master until there are as many as three outstanding address tenures waiting for a data bus tenure to complete or begin. Since the device supports two masters on the system bus, there can be as many as six address tenures on the 60x system bus that have not completed or begun a data bus tenure. The arbiter stops granting the address bus to a particular master after its third address tenure. The device can also drive a seventh, address-only, tenure onto the bus to satisfy a DMA snoop operation. The arbiter maintains a one level pipeline per master. The device stops granting the address bus to a master after it has two outstanding address tenures waiting for a data bus tenure to complete . With two masters in the system, there could be as many as four outstanding address tenures waiting for a data bus tenure to complete or begin, and a fifth device generated address-only tenure. Pipelining is completely disabled. Even with two masters in the system, there will only be one address tenure waiting for a data tenure to complete. Implemented to accommodate slave devices like an L2 lookaside that can only support one level pipeline regardless of the number of masters on the 60x bus. Page 152 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM Preliminary Draft IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller Arbiter Requirements Internal ABB All devices on the 60x bus must generate an internal ABB. Because the arbiter may grant the address bus to a requesting device while another master is active, the requesting master must generate an ABB based on SYS_TS and SYS_AACK. The current master does not provide an ABB. Qualified SYS_BG Equation Use the following equation to detect a qualified bus grant using positive logic: QBG = SYS_BG + ABB + SYS_ARTRY where ABB represents the interval between SYS_TS and SYS_AACK active Note: Bus Request (SYS_BR) need not be active to detect a qualified bus grant (parked case). SYS_TS Assertion All master devices must drive SYS_TS active in the cycle immediately following a qualified address bus. Otherwise, the address tenure is aborted and another master is free to drive the address bus. SYS_BR Negation All master devices must negate SYS_BR for at least one bus cycle immediately after receiving a qualified bus grant. Qualified SYS_DBG Equation The equation for qualified SYS_DBG using positive logic is: QDBG = SYS_DBG + ARTRY DBB is unused because the arbiter does not issue a SYS_DBG when DBB is active. The arbiter monitors transaction sizes to determine the end of a data bus tenure and waits until the previous data tenure is complete before issuing a SYS_DBG to the next master. Note: QDGB can only be negated by an SYS_ARTRY of the address tenure associated with the QDBG data bus tenure. Therefore, once the SYS_ARTRY window has passed for an address tenure, the data bus tenure associated with that address tenure cannot be negated by SYS_ARTRY from a subsequent address tenure. High Impedance After SYS_TEA Masters and slaves must execute all data bus signals as high impedance within two bus clocks from SYS_TEA assertion. SYS_DRTRY Assertion Slaves are not allowed to drive SYS_DRTRY active. The device arbiter does not receive SYS_DRTRY. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 153 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Slave Data Bus Determination To determine whether the data bus is currently in use by a previous address tenure, a slave must sample DBB from its master during the TS active cycle. If DBB is active, the slave must wait for DBB to go inactive in a one-level pipeline mode for at least one cycle before providing read data or accepting write data. SYS_L2_Hit Assertion For the device to determine whether an addressing error has occurred, all slaves on the 60x bus must assert SYS_L2_HIT when selected by an address on the 60x bus. Warning: The SYS_L2_HIT signal is subject to timing constraints. Page 154 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM Preliminary Draft IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller Bus Enhancements DBB not Required by Masters Masters do not require DBB. The arbiter does not grant the data bus to a requesting master if the bus is currently in use. The device does not drive DBB since it acts as an address-only bus master. Half-Cycle Precharge not Required on SYS_TA The device can be programmed so the half-cycle precharge of SYS_TA is not required. This requires all slaves to initially drive SYS_TA active or inactive immediately following a data bus grant. At the end of a data bus tenure, a slave does not perform a precharge, which requires a slave in the next data bus tenure to drive SYS_TA in the first cycle of the tenure. The ABCNTL[13] mode bit , “-60x Arbiter Control Register (ABCNTL)” Page 104 - forces the device to do a precharge if a slave on the 60x bus does not support this function. Half-Cycle Precharge not Required on SYS_TEA The arbiter does not grant the data bus for two bus cycles following assertion of SYS_TEAs. This allows a slave to perform a full cycle precharge on SYS_TEAs. SYS_ARTRY_PREV in QDBG Equation Eliminated When SYS_ARTRY is asserted, the arbiter negates all bus grants in the cycle following SYS_ARTRY. This supplants the requirement for masters to qualify associated bus grants by asserting SYS_ARTRY in a previous cycle. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 155 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft 60x Bus Transfer Types and Sizes The following tables describe the transaction types supported by the device on the processor bus. The device supports the PowerPC 604 critical double word burst transactions. Non-Burst Transactions (SYS_TBST = 1) SYS_TSIZ[0:2] A[29:31] Definition Note 000 000 - 111 8-byte transfer 001 000 - 111 1-byte transfer 010 000 - 111 2-byte transfer 011 000 - 111 3-byte transfer 100 000 - 111 4-byte transfer 101 000 - 111 5-byte transfer 110 000 - 111 6-byte transfer 111 000 - 111 7-byte transfer 1 1. For transfers where the number of bytes to transfer cross a doubleword boundary, the device will truncate the transfer size to avoid crossing a doubleword boundary. Burst Transactions (SYS_TBST = 0) SYS_TSIZ[0:2] A[27:31] Definition Support Notes 000 xxxxx 8 Byte transfer No 2 00xxx 16-byte transfer beginning on 32-byte boundary 01xxx 16-byte transfer beginning on odd doubleword boundary 10xxx 16-byte transfer beginning on odd 16-byte boundary 11xxx 16-byte transfer beginning on odd doubleword boundary 00xxx 32-byte transfer beginning on 32-byte boundary 01xxx 32-byte transfer beginning on odd doubleword boundary TBD No 001 010 TBD No 1,3 Yes 10xxx 32-byte transfer beginning on odd 16-byte boundary 1,3 11xxx 32-byte transfer beginning on odd doubleword boundary 1,3 1. For transfers that cross a 32-byte boundary, the device will wrap to the beginning of the 32-byte block to satisfy the data transfer. 2. Unpredictable results will occur if this transfer size is attempted on the processor bus. 3. Not supported on store operations Page 156 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Transfer Types TT[0:4] Operation Transaction Support as Master Support as Slave 00000 Clean Sector Address-only Yes NOP 00001 LARX Reservation Set Address-only No NOP 00010 Write with Flush SBW or Burst No Yes 00011 Reserved (arbiter will assume address-only transaction) 00100 Flush Sector Yes NOP 00101 Reserved (arbiter will assume address-only transaction) 00110 Write with Kill No Yes (treated as 00010) 00111 Reserved (arbiter will assume address-only transaction) 01000 SYNC Address-only No Yes 01001 TLBSYNC Address-only No Yes 01010 Read SBR or Burst No Yes 01011 RWNITC - Read with no Intent to Cache SBR or Burst No Yes (treated as 01010) 01100 Kill Sector Address-only Yes NOP 01101 ICBI Address-only No NOP 01110 RWITM - Read with Intent to Modify Burst No Yes (treated as 01010) 01111 Reserved (arbiter will assume address-only transaction) 10000 EIEIO No Yes 10001 Reserved (arbiter will assume address-only transaction) 10010 Write with Flush Atomic No Yes (treated as 00010) 10011 Reserved (arbiter will assume address-only transaction) 10100 ECOWX - Graphics Write No Yes No Yes (601 mode only) No Yes (treated as 01010) No Yes No Yes (treated as 01010) Address-only Burst Address-only SBW SBW 10101 Reserved (arbiter will assume address-only transaction) 1011x 11000 TLB Invalidate Address-only 11001 Reserved (arbiter will assume address-only transaction) 11010 Read Atomic 11011 Reserved (arbiter will assume address-only transaction) 11100 ECIWX - Graphics Read 11101 Reserved (arbiter will assume address-only transaction) 11110 RWITM Atomic 11111 Reserved (arbiter will assume address-only transaction) SBR or Burst SBR Burst Note: SBW = Single Beat Write, SBR = Single Beat Read CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 157 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Data Gathering The 60x logic gathers data for CPU store-transfers to the PCI bus bridges. During data gathering, single beat stores of up to 32bytes from the CPU are gathered before being sent to the PCI bus bridge unit. Data gathering reduces asynchronous boundary crossings and facilitates data bursting on the PCI bus. Data Gathering Algorithm PCI logic went idle Idle If there are store buffers that have not been transferred to PCI, send to PCI logic Single beat store to PCI Memory Space Is address gatherable or first? No If there are store buffers that have not been transferred to PCI, send to PCI logic Yes Is there a store buffer available? Yes Save address for compare No SYS_TA the data off 60x bus and place in buffer Wait for buffer to empty Is PCI bridge logic busy? No Yes Is this the last location in the buffer? Yes No Reset first flag Page 158 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Initiate command to send store buffer data to PCI CPC710_60X.fm.01 11/4/1999 IBM Preliminary Draft IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller SYNC and EIEIO When a processor executes a SYNC instruction, a SYNC address-only tenure is broadcast on the 60x bus to notify the system that a software-placed barrier is present. The system is responsible for ensuring all previously executed load and store operations are complete and all resultant actions are visible to the system. The device satisfies this requirement by SYS_ARTRYing the SYNC operation until all of its store buffers are empty, all reads have been executed, and all data have been placed in internal device buffers for requests issued by the same processor issuing SYNC. When a processor broadcasts an EIEIO on the 60x bus, the system is responsible for ensuring all previous transactions are complete before executing operations. The device does not SYS_ARTRY the EIEIO because the 60x logic dispatches bus transactions to the logic units in the order in which they occur on the system bus and each logic unit executes its commands in the order received. For diagnostic purposes, the device can be programmed to SYS_ARTRY the EIEIO in the same manner as SYNC. The logic units are system memory, PCI-32 bus bridge, PCI-64 bus bridge, system I/O logic, and DMA controller logic. EIEIO operations are valid for transfers to and from the same logic unit, but execution order of load and store operations to different logic units cannot be guaranteed. For example, a store to the PCI-32 bus bridge followed by a PCI-64 store could be presented to the respective PCI buses in reverse order if a bus is busy. To preserve the order among logic units, software must issue a SYNC instead of an EIEIO. Address Retry (SYS_ARTRY) Precharging SYS_ARTRY and SYS_SHD The CPC710 device always precharges SYS_ARTRY and SYS_SHD. All other devices on the 60x bus must disable their precharges of these signals. The device negates SYS_ARTRY and SYS_SHD for a half bus cycle during the second cycle following the SYS_ARTRY window’s last cycle. SYS_ARTRY Assertions The device asserts SYS_ARTRY for: • SYNC operations as described in the previous section • EIEIO operations as described in the previous section • XFERDATA when more than two transfers have been initiated • a processor access to the PCI bus when a PCI-ISA bus bridge requests the same PCI bus • a processor access to system memory when a DMA occurs to the same cache line • a processor access to system memory when a DMA operation occurs to the same line • a processor access into a range of PCI-32 or PCI-64 addresses defined as potential deadlock Recommended SYS_ARTRY Procedure • A master that has had its address tenure retried should negate its SYS_BR[n] for at least one bus cycle in the cycle immediately following detection of an active SYS_ARTRY. • A master that has retried an address tenure due to a snoop hit should activate its SYS_BR[n] in the cycle immediately following the detection of an active SYS_ARTRY. This ensures the master that retries is serviced before the master that was retried. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 159 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Locking Signal DLK The device can set the DLK output for CPU access to the PCI-32 or PCI-64 bus when: • input NODLK is not active (=’1’) • the access is within the address range defined by the selected bridge’s registers SMDLK1/2 or SIDLK1/2 • bit 24 of the PGCHP register is ’1’. The 60x CPU can then receive an SYS_ARTRY when the NODLK signal becomes active (=’0’). Page 160 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM Preliminary Draft IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller 60x Bus Configuration The system uses configuration cycles to identify and configure BUCs on the 60x bus. The following rules apply to configuration cycles: • All configuration cycles must use the Basic Transfer Protocol. • The BUC responds to addresses in the configuration space only when its SYS_CONFIG[n] is active. • All configuration cycles must be single beat, word-aligned word accesses except for accesses to the feature ROMs that are configured for byte access. • BUCs must respond to DCR reads at SYS_L2_HIT assertion as shown in the following figure. Otherwise, the device assumes no device is present and SYS_TAs the CPU with data indicating no device present. 60x Bus Configuration Cycle BUS_CLK SYS_TS SYS_AACK SYS_CONFIG[n] SYS_DBG SYS_L2_HIT SYS_TA Note: For in-line L2 caches, the L2 cache controller only supports configurations from its local processor. Software should not configure the controller from a processor on the system bus side of the controller. This makes it unnecessary for this kind of L2 cache controller to drive SYS_L2_HIT. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 161 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Error Handling for CPU-Initiated Transactions The devices uses Machine Checks to indicate errors. This allows software to log errors before the system is shut down. In an MP environment, the device activates the Machine Check pin that corresponds to the CPU initiating the transaction. Because the PowerPC 601 does not provide this pin, the checkstop pin is used. Checkstop Errors The device generates a checkstop when the following are detected: • Address parity error on the 60x system bus (if enabled) • Data parity error on 60x system bus (if enabled) • Internal timeout due to no response from slave on load The 60x logic performs the following when generating a checkstop: 1. Sets appropriate bit(s) in SESR 2. Drives CHKSTOP active until power on reset The following table describes the error handling performed for CPU initiated transactions. The 60x logic drives SYS_MACHK signals, not the PCI bridge logic or the memory control logic. Error Handling for CPU Initiated Transactions (Page 1 of 4) Operation Error Access not directed to device Addressing Error (SYS_L2_HIT not driven active) Access to device Bus Time-out: Time expired from SYS_AACK active to first SYS_TA Mode Notes Disabled No action taken Enabled Set No Select error bit in SESR Set error address in SEAR PGCHP[26] = 0: Signal Machine Check with SYS_TEA PGCHP[26] ≠ 0: Signal Machine Check with SYS_MACHK Disabled Inhibit timer; no action taken Enabled Set bus time-out error bit in SESR Set checkstop generated bit in SESR Set error address in SEAR Signal Checkstop Access to a reserved or non- implemented address Access to internal device facilities Action Terminate CPU transaction normally 1 Alignment or size Store to read-only register Load from write-only register 1. A dummy 0 is returned for read operation. For write, data is ignored. Page 162 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Error Handling for CPU Initiated Transactions (Page 2 of 4) Operation Error Single bit error Mode Action Notes Don’t care Set single-bit error and syndrome in MESR Set error address in MEAR Return corrected data to CPU If PGCHP[17] = 1 and PGCHP[26] = 1: Set memory error bit in SESR Set memory error address in SEAR Signal Machine Check with SYS_MACHK Normal Set error in MESR Set error address in MEAR Set memory error bit in SESR Set memory error address in SEAR if PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1, signal Machine Check with SYS_MACHK Diagnostic Set double-bit error in MESR Set error address in MEAR Return uncorrected data to CPU Signal Machine Check with SYS_MACHK if write less than eight bytes Access to system memory Double-bit error No DEVSEL received Master-abort the PCI transaction Set master-aborted bit 13 in PCI Status register Set device error bit in PLSSR register Set PCI error bit in SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally 1 Detected SERR active during PCI transaction Master-abort the PCI transaction Set master aborted bit 13 in PCI Status register Set SERR detected error in PLSSR register Set PCI error bit in SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally 1 Access to PCI bus 1. A dummy 0 is returned for read operation. For write, data is ignored. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 163 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Error Handling for CPU Initiated Transactions (Page 3 of 4) Operation Error Detected PCI bus data parity error on load Mode Action Notes Enabled by bit 6 in PCI CMND register Continue transfer on PCI bus to completion Activate the PERR signal Set data parity error bit 8 in PCI Status register Set data parity error bit 15 in PCI Status register Set PCI error bit in SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally Disabled by bit 6 in PCI CMND register. Set parity error bit 15 in PCI Status register Proceed normally with PCI transaction Proceed normally with CPU transaction Enabled by bit 6 in PCI CMND register Continue transfer on PCI bus to completion Set data parity error bit 8 in PCI Status register Set data parity error bit 15 in PCI Status register Set PCI error bit in SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally Disabled by bit 6 in PCI CMND register Set data parity error bit 15 in PCI Status register Proceed normally with PCI transaction Proceed normally with CPU transaction Access to PCI bus (cont’d) Detected PERR on store Detected target abort Set received target abort bit in PCI Status register Set PCI error bit in SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally 1 1 1 1. A dummy 0 is returned for read operation. For write, data is ignored. Page 164 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_60X.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Error Handling for CPU Initiated Transactions (Page 4 of 4) Operation Error PCI Bus timeout: P/G_TRDY count expired Mode Action Notes Enabled Master-abort the PCI transaction Set master aborted bit 13 PCI Status register Set PCI bus time-out error in PLSSR register Set PCI error bit in SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally 1 Enabled Stop retrying PCI transfer Set retry count expired bit in PLSSR register Set PCI error bit is SESR Set error address in SEAR register If PGCHP[26] = 0: Loads: Signal Machine Check with SYS_TEA Stores: Signal Machine Check with SYS_MACHK If PGCHP[26] = 1: Signal Machine Check with SYS_MACHK Terminate CPU transaction normally 1 Access to PCI bus (cont’d) Retry count expired 1. A dummy 0 is returned for read operation. For write, data is ignored. CPC710_60X.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 165 of 209 IBM Dual Bridge and Memory Controller Page 166 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 IBM Preliminary Draft CPC710_60X.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Memory Controller Overview The device’s memory controller controls processor and I/O interactions with the memory system. The memory controller supports SDRAM and is 2-way interleaved to allow the memory to burst data on every CPU bus cycle at 100 MHz (1-1-2-1 after initial latency) using only one memory address bus. To handle critical word load, individual control of the LSB column address bits is required for the DIMM pair. The controller supports up to eight dual DIMMs banks of interleaved 72-bit memory (64-bit Data + 8-bit ECC). To reduce pin count, the controller requires a Texas Instruments (TI) ALVCH162268 MUX to externally multiplex the 144-bit data to 72-bits for device input. Programmable parameters allow a variety of memory organizations and timings. ECC protection is provided for all 64 bits of the data bus, detecting and correcting single- and double-bit errors. Different SDRAM organizations can be mixed (Supported SDRAM Organizations on page 175). 60x bus operation is limited to 100 MHz. Programmable parameters allow for a variety of memory organizations (See “Supported SDRAM Organizations” on page 175.). The SDRAM must comply with the following requirements (compatible with the PC100 Specification [1]) . • CAS Latency = 2 • Burst length = 2 • Maximum tRCDmin allowed is 2 Clock cycles. • Maximum tRPmin allowed is 2 Clock cycles. • Maximum tRASmin allowed is 5 Clock cycles. It is possible to use Extended Data Out/Hyper-Page DRAM (EDO/HPM DRAM) with IBM Dual Bridge and Memory Controller, but this application is not fully supported: contact your support for more informations. Only one type of RAM can be used in a system (it is not possible to mix SDRAM with DRAM devices). However, different kind of SDRAM organizations can be mixed. 60x bus operation is limited to 75 MHz when using EDO DRAM and to 100 MHz when using SDRAM. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 167 of 209 IBM Dual Bridge and Memory Controller Memory Performance for Cache Line Operations (ECC Active) Cas Latency = 2 Pipeline Levels Operation 100 MHz 160 MB/s Initial Read Burst 16-1-2-1 Page Miss Sustained Page Hit 0 Sustained 160 MB/s 16-1-2-1 3-1-1-1 Page Miss Page Hit 160 MB/s Initial Read Burst 16-1-2-1 533 MB/s Initial Write Burst 160 MB/s 16-1-2-1 Page Miss Sustained Page Hit 228 MB/s 10-1-2-1 400 MB/s 4-1-2-1 564 MB/s 2 3-1-1-1-21-1-1-2-11-2 Initial Write Burst Page Miss Sustained Page Hit Page 168 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 246 MB/s 10-1-1-1 400 MB/s 5-1-1-1 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bank Definitions The word "Bank" covers a couple of different meanings, depending on the point-of-view: 1. SDRAM Banks 2. DIMM Banks 3. Interleaved Banks SDRAM Banks As shown in the following diagram, SDRAMs contain memory arranged in two or four banks. The Memory Controller selects these banks using Bank Select (BS) address pins. SDRAM Bank Configuration BANK 0 BANK 1 BANK 0 BANK 1 BS [0] BS [1] BANK 2 BANK 3 BS [0] SDRAM with two banks CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 SDRAM with 4 banks Page 169 of 209 IBM Dual Bridge and Memory Controller DIMM Banks As shown in the following diagram, DIMMs are available in single bank and dual bank configurations. DIMM Bank Configuration Dual Bank DIMM Single Bank DIMM SDRAM Chip Nothing on this side DIMM DIMM These 5 chips constitute DIMM Bank A These 5 chips constitute DIMM Bank B These 5 chips constitute DIMM Bank A Bank Representation DIMM Bank B DIMM Bank A Schematic Representation Page 170 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 DIMM Bank A Schematic Representation CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Interleaved Banks An Interleaved Bank consists of two interleaved DIMM Banks. The two DIMM Banks are called Odd and Even. As shown in the following figures, MCER registers must be programmed according to the DIMM Bank configuration used. Since the device works in an interleaved way, the minimum equipment required is two Single or Dual DIMM Banks. Single Bank DIMM (Odd) DIMM Bank A MCER1 DIMM Bank A MCER0 Programming with Single Bank DIMMs Interleaved Bank 1 (empty) Interleaved Bank 0 (programmed) Single Bank DIMM (Even) MCER0 (for Interleaved Bank 0) must be programmed. MCER0 (for Interleaved Bank 1) must be empty, or bit ’0’ set to ’0’. All unused MCERx locations must be empty. DIMM Bank A Dual Bank DIMM (Odd) DIMM Bank B DIMM Bank A MCER0 DIMM Bank B MCER1 Programming with Dual Bank DIMMs Interleaved Bank 1 (programmed) Interleaved Bank 0 (programmed) Dual Bank DIMM (Even) MCER0 and MCER1 (for Interleaved Banks 0 and 1) must be programmed. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 171 of 209 IBM Dual Bridge and Memory Controller Memory Signal Connections SDRAM Common Signals Signal Name Type MDATA[0:71] 72-bit Data MADDR[1:12] MADDR0_ODD Address MADDR0_EVEN External MUX Controller for Memory Data Signal Name Toggle for Reads Toggle for Writes MUXCLKEN1B Yes No (’1’b) MUXCLKEN2B Yes No (’1’b) MUXCLKENA1 No (’1’b) Yes MUXCLKENA2 No (’1’b) Yes MUX_OEA No (’1’b) No (’0’b) MUX_OEB No (’0’b) No (’1’b) MUX_SEL High for EVEN Low for ODD No (’1’b) \ Memory Address Bit Definition for Non-Row Column Addressing Bits Address Bit Definition 0-1 ’00’: 28 Interleaving Bit 0: Even DIMMs (0, 2, 4, or 6) 1: Odd DIMMs (1, 3, 5, or 7) Page 172 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Base address of memory CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller SDRAM Subsystem Signals Signal Name Type Comments BS0 SDRAM Bank Select BS1 SDCS[0:7] Chip Select See the following table for connections SDDQM[0:7] Data Mask 8 pins for load purposes SDRAS[0:3] Row Address Strobe 4 pins for load purposes SDCAS[0:3] Column Address Strobe 4 pins for load purposes WE[0:3] Write Enable 4 pins for load purposes SDCKE[0:7] Clock Enable 8 pins for load purposes SDRAM DIMM Chip Select Connections Signal Name DIMM and DIMM Bank SDCS[0] DIMM 0, Bank A SDCS[1] DIMM 1, Bank A SDCS[2] DIMM 0, Bank B SDCS[3] DIMM 1, Bank B SDCS[4] DIMM 2, Bank A SDCS[5] DIMM 3, Bank A SDCS[6] DIMM 2, Bank B SDCS[7] DIMM 3, Bank B CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 173 of 209 IBM Dual Bridge and Memory Controller SDRAM Subsystem Overview ADDR - ODD [0:12] MADDR0_ODD MADDR[1:12] ADDR - EVEN [0:12] MADDR0_EVEN BS0/BS1 Memory Interface 8x SDDQM 4x SDRAS 4x SDCAS 4x WE 8x SDCKE SDCS[0:7] MUX_CLKENA1 MUX_CLKENA2 MUX_CLKEN1B MUX_CLKEN2B MUX_OEA MUX_OEB MUX_SEL MDATA[0:71] TI ALVCH162268 MUX 1B A1 6X 2B DH [0:71] DL [0:71] DL[0:71], MADDR_EVEN[0:12] DH[0:71], ADDR_ODD[0:12] SDCS2 SDCS3 DIMM Bank B DIMM Bank B DIMM Bank A DIMM Bank A DIMM 0 MCER1 SDCS1 MCER0 SDCS0 DIMM 1 SDCS6 SDCS7 DIMM Bank B DIMM Bank A DIMM Bank B DIMM Bank A DIMM 2 MCER3 SDCS5 MCER2 SDCS4 DIMM 3 SDRAS, SDCAS, WE, SDCKE, BS0, BS1, SDDQM, CLK Note: The input clock for the SDRAM is the 60x bus clock, which is not driven by the device. Page 174 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Supported SDRAM Organizations The IBM25CPC710AB3A100 is fully compatible with the JEDEC Standard. It supports the addressing listed in the following table. Supported DIMMs DIMM Size (MByte) Addressing (Row/Col/ SDRAM Bank) SDRAM (Mbits x I/Os) Number of Chips per Bank with ECC DIMM Size (MByte) Addressing (Row/Col/ SDRAM Bank) SDRAM (MB x I/Os) Number of Chips per Bank with ECC 8M Single 11/8/1 1Mx16 4+1 16M Single 11/9/1 11/9/1 11/8/2 12/8/1 2Mx8 2Mx32 2Mx32 2Mx8 8+1 2+1 2+1 8+1 16M Dual 11/8/1 1Mx16 4+1 32M Single 11/10/1 11/10/1 12/9/1 12/8/2 13/8/1 4Mx4 4Mx16 4Mx4 4Mx16 4Mx16 16 + 2 4+1 16 + 2 4+1 4+1 32M Dual 11/9/1 11/9/1 11/8/2 12/8/1 2Mx8 2Mx32 2Mx32 2Mx8 8+1 2+1 2+1 8+1 64M Single 12/9/2 12/9/2 13/8/2 13/9/1 8Mx8 8Mx32 8Mx32 8Mx8 8+1 2+1 2+1 8+1 64M Dual 11/10/1 11/10/1 12/8/2 12/9/1 13/8/1 4Mx4 4Mx16 4Mx16 4Mx4 4Mx16 16 + 2 4+1 4+1 16 + 2 4+1 128M Single 12/10/2 12/10/2 13/10/1 13/9/2 16Mx4 16Mx16 16Mx4 16Mx16 16 + 2 4+1 16 + 2 4+1 128M Dual 12/9/2 12/9/2 13/8/2 13/9/1 12/9/2 8Mx8 8Mx32 8Mx32 8Mx8 8Mx16 8+1 2+1 2+1 8+1 4+1 12/10/2 12/10/2 12/10/2 13/10/1 13/9/2 16Mx4 16Mx8 16Mx16 16Mx4 16Mx16 16 + 2 8+1 4+1 16 + 2 4+1 256M Single 13/10/2 32Mx8 8+1 256M Dual 512M Single 13/11/2 64Mx4 16 + 2 512M Dual 13/10/2 13/10/2 32Mx8 32Mx4 8+1 16 + 2 1024M Dual 13/11/2 64Mx4 16 + 2 Note: The number of chips per MCER is double the number of chips per DIMM bank. SDRAM Buffering Requirements The SDRAM interface is designed to run in a 100 MHz environment. Because signal loading is critical, some outputs connect to four or eight pins. The following table lists loads and running frequencies for all SDRAM signals that use the 60x bus clock. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 175 of 209 IBM Dual Bridge and Memory Controller SDRAM Input Signal Frequencies Maximum Input Capacitance Signal Name Running Frequency Note SDRAM (Note 1) Unbuffered DIMM (Note 2) SDCS BUS_CLK 5pF 30pF 3 SDCKE BUS_CLK 5pF 50pF 3 MDATA0/1 BUS_CLK/2 7pF 15pF MADDR0/1 BUS_CLK/2 5pF 50pF BS BUS_CLK/2 5pF 50pF SDRAS BUS_CLK/2 5pF 50pF SDCAS BUS_CLK/2 5pF 50pF WE BUS_CLK/2 5pF 50pF SDDQM BUS_CLK/2 5pF 50pF 1. These are usual values for a single SDRAM chip (V=3.3V, T=25C, f=1MHz) 2. These are usual values for an unbuffered DIMM (8 x 1M x 16) (V=3.3V, T=25C, f=1MHz) 3. Signal is critical, runs at full speed. DIMM Row Address Derivation for SDRAM x72 Width DIMM Row Address DIMM Addressing 12 11 10 9 8 7 6 5 4 3 2 1 0 13/11/2 4 7 9 10 11 12 13 14 15 16 17 18 19 13/10/2 4 7 9 10 11 12 13 14 15 16 17 18 19 13/9/2 4 7 9 10 11 12 13 14 15 16 17 18 19 13/10/1 4 7 9 10 11 12 13 14 15 16 17 18 19 13/9/1 5 7 9 10 11 12 13 14 15 16 17 18 19 13/8/2 6 7 9 10 11 12 13 14 15 16 17 18 19 13/8/1 6 7 9 10 11 12 13 14 15 16 17 18 19 12/10/2 - 7 9 10 11 12 13 14 15 16 17 18 19 12/9/2 - 7 9 10 11 12 13 14 15 16 17 18 19 12/8/2 - 7 9 10 11 12 13 14 15 16 17 18 19 12/9/1 - 7 9 10 11 12 13 14 15 16 17 18 19 12/8/1 - 7 9 10 11 12 13 14 15 16 17 18 19 11/10/1 - - 9 10 11 12 13 14 15 16 17 18 19 11/9/1 - - 9 10 11 12 13 14 15 16 17 18 19 11/8/2 - - 9 10 11 12 13 14 15 16 17 18 19 11/8/1 - - 9 10 11 12 13 14 15 16 17 18 19 Page 176 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller DIMM Column and Bank Address Derivation for SDRAM x72 Width 13/11/2 DIMM Bank Address DIMM Column Address DIMM Addressing 11 102 9 8 7 6 5 4 3 2 1 01 1 0 2 - 3 6 20 21 22 23 24 25 26 27 5 8 13/10/2 - - 3 6 20 21 22 23 24 25 26 27 5 8 13/9/2 - - - 6 20 21 22 23 24 25 26 27 5 8 13/10/1 - - 5 6 20 21 22 23 24 25 26 27 - 8 13/9/1 - - - 6 20 21 22 23 24 25 26 27 - 8 13/8/2 - - - - 20 21 22 23 24 25 26 27 5 8 13/8/1 - - - - 20 21 22 23 24 25 26 27 - 8 12/10/2 - - 4 6 20 21 22 23 24 25 26 27 5 8 12/9/2 - - - 6 20 21 22 23 24 25 26 27 5 8 12/8/2 - - - - 20 21 22 23 24 25 26 27 6 8 12/9/1 - - - 6 20 21 22 23 24 25 26 27 - 8 12/8/1 - - - - 20 21 22 23 24 25 26 27 - 8 11/10/1 - - 6 7 20 21 22 23 24 25 26 27 - 8 11/9/1 - - - 7 20 21 22 23 24 25 26 27 - 8 11/8/2 - - - - 20 21 22 23 24 25 26 27 7 8 11/8/1 - - - - 20 21 22 23 24 25 26 27 - 8 1. The Memory Controller interleaves with only one memory address bus. To handle critical word load, individual control of the LSB column address bits is required for the DIMMs. MADDR0_ODD is used for the LSB address of the even and odd DIMMs. 2. Bit 10 is never used as address during CAS phase. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 177 of 209 IBM Dual Bridge and Memory Controller Memory Controller Registers MCCR Register The Memory Controller Control Register contains all the parameters to fit the Memory Controller to the Synchronous DRAM components used. The following table describes how to program the MCCR Register (Memory Controller Control Register (MCCR) on page 121. Bit(s) Description 0 Global System Memory Address Space Enable 0: Device will not respond to addresses specified in Memory Configuration Extent Register (MCERx) 1: System memory address space enabled. 1 Diagnostic Mode This bit is used to control presentation of double-bit ECC errors to the system. This bit is primarily intended for use in memory testing at power on time. Software can use this bit when testing memory and or ECC logic in order to avoid the hardware generating a machine check for double-bit ECC errors. The error however, is still logged into the MEAR 0: Normal Mode: Multi-bit ECC error will generate Machine Check 1: Diagnostic Mode: Multi-bit ECC does NOT generate Machine Check; logged in MEAR & MESR 2 SDRAM Initialization Status (read-only) 0: SDRAM initialization is not completed. 1: SDRAM initialization is completed. ECC Mode This field provides software with a means to control ECC generation and checking. b’01’ is provided to allow software direct read/write access to the ECC byte that is associated with every doubleword of data stored in memory and also provide a mechanism to verify the memory controller’s ECC generation and checking logic. In this mode, byte lane 0 data (MSB of a double word) is written to the ECC byte instead of the normal ECC code byte. Data byte 0 will be forced to all zeros. For reads, byte 0 will contain the byte stored in the ECC byte, not the data at byte 0. ECC checking is not enabled for reads in this mode. This mode also allows firmware write single-bit and multi-bit errors into memory to allow for ECC logic testing. 00: 3-4 01: 10: 11: 5-7 Normal generation and checking of ECC codes. The device will generate the normal ECC code when writing to memory and check ECC when reading. ECC check disabled; Byte lane 0 routed to/from ECC check field. Data byte 0 forced to all zeros This mode is provided to allow software direct read/write access to the ECC byte that is associated with every doubleword of data stored in memory and also provide a mechanism to verify the memory controller’s ECC generation and checking logic. In this mode, byte lane 0 data (MSB of a double word) is written to the ECC byte instead of the normal ECC code byte. Data byte 0 will be forced to all zeros. For reads, byte 0 will contain the byte stored in the ECC byte, not the data at byte 0. ECC checking is not enabled for reads in this mode. This mode also allows firmware write single-bit and multi-bit errors into memory to allow for ECC logic testing. The device will still generate normal ECC codes when writing to memory. ECC check disabled; Normal routing of data and normal ECC code generation The device will still generate normal ECC codes when writing to memory. Reserved Row Cycle Time for SDRAM Auto-refresh (tRC) Allows to fit the delay between the Refresh Command and the next Activation. This delay has to be at least the tRCmin value specified in the SDRAM datasheet. 000: 5 bus cycles 001: 6 bus cycles 010: 7 bus cycles 011: 8 bus cycles 100: 9 bus cycles 101: 10 bus cycles 110: 11 bus cycles 111: 12 bus cycles Page 178 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Bit(s) 8-9 10 11 Description DRAM Type Must be set to 10 for SDRAM Data Pacing Mode (Must be set to 1 for SDRAM) Data Mask Mode (SDRAM only) 0: 16 SDCS are available. DQM pin of SDRAM devices must be grounded. 1: Only eight SDCS are available. DQM signal is present on the eight other pins. Activate to prevent tRDL violation during “Write interrupted by pre-charge” operations if the device does not guarantee that the data presented in the same time as pre-charge is not properly ignored. 12 - 15 Reserved. Must be left to 0 16 Reserved. Must be set to 0 17 Reserved. Must be set to 1 18 Reserved. Must be set to 1 19 Reserved. Must be set to 0 20 Reserved. Must be set to 0 21 - 22 23 24 - 29 Reserved. Must be set to b’00’ Reserved. Must be set to 0 Reserved 30 Disable Page Mode 0: Memory controller will perform fast page accesses for back to back operations if appropriate 1: Memory controller will perform fast page access only within a burst operation. It will NOT perform fast page accesses for back to back bursts even if they occur to the same RAS page. 31 Disable Queue Same Page Override 0: Memory queue ordering can be overridden if an operation is to the same page. 1: Memory queue always processed in order received. MCCR Register Settings 0000 0 1 1 0 0 00 31 30 29 28 27 26 25 24 23 21 22 20 19 1 1 18 10 17 011 16 10 00 11 8-9 2 5-7 1 0 3-4 SDRAM with tRC=8 cycles 1 0 Configuration 12-15 Register Bits 0 0 Note: Values written in bold font are mandatory for the specified configuration. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 179 of 209 IBM Dual Bridge and Memory Controller MCER Register The Memory Configuration Extent Registers (MCER [0:7]) program the start address and size of each bank. The following table shows the relationship between the DIMMs and the MCER registers. MCER to Program Functions of DIMMs Bank Definition (DIMMs equipped) Corresponding MCER Note DIMM0-Bank1 and DIMM1-Bank1 MCER0 DIMM0-Bank2 and DIMM1-Bank2 MCER1 DIMM2-Bank1 and DIMM3-Bank1 MCER2 DIMM2-Bank2 and DIMM3-Bank2 MCER3 DIMM4-Bank1 and DIMM5-Bank1 MCER4 1 DIMM4-Bank2 and DIMM5-Bank2 MCER5 1 DIMM6-Bank1 and DIMM7-Bank1 MCER6 1 DIMM6-Bank2 and DIMM7-Bank2 MCER7 1 1. When using SDRAM and Data Mask, Mode is active (see MCCR, bit 11) and device can support only up to four bank. MCER [4:7] must be off. To configure contiguous address spaces with different bank sizes, software must put the largest bank sizes at the lowest addresses and continue in order to the smallest bank sizes. To set up the MCER registers, software must read the PD bits and the ID bits for each DIMM. These bits are located in the System I/O registers (see System I/O Register 0 (SIOR0) on page 127). The following table describes how to initialize these registers. MCER Register Initialization (see notes 1-4) Device Bank Size (MB) DIMM Description MCER(x) Bits[16:25] MCER(x+1) Bits[16:25] Not equipped x’3F3’ Off 4 4 x’3F3’ x’3F3’ 1 8 Not equipped x’3E3’ Off 8 2 8 8 x’3E3’ x’3E3’ 8 1 16 Not equipped x’3C3’ Off 16 2 16 16 x’3C3’ x’3C3’ 16 1 32 Not equipped x’383’ Off 32 2 32 32 x’383’ x’383’ DIMM Size (MB) Number of Banks per DIMM Bank x Bank x+1 2 1 4 4 2 4 1. "DIMM size" is the size in MB of one DIMM (including Bank A and Bank B if dual bank DIMM). 2. "Number of banks per DIMM": One for single bank DIMM (i.e., DIMM equipped with Bank A only); two for dual bank DIMM (i.e., DIMM equipped with Bank A and Bank B). 3. x in MCER(x) = 0, 2, 4, or 6 4. a setting of “off” indicates that the bank must be disabled by setting MCER(x) Bit 0 = 0. Page 180 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller MCER Register Initialization (see notes 1-4) Device Bank Size (MB) DIMM Description MCER(x) Bits[16:25] MCER(x+1) Bits[16:25] Not equipped x’303’ Off 64 64 x’303’ x’303’ 1 128 Not equipped x’203’ Off 128 2 128 128 x’203’ x’203’ 128 1 256 Not equipped x’003’ Off 256 2 256 256 x’003’ x’003’ 256 1 512 Not equipped x’002’ Off 512 2 512 512 x’002’ x’002’ 512 1 1024 Not equipped x’000’ Off 1024 2 1024 1024 x’000’ x’000’ DIMM Size (MB) Number of Banks per DIMM Bank x Bank x+1 32 1 64 64 2 64 1. "DIMM size" is the size in MB of one DIMM (including Bank A and Bank B if dual bank DIMM). 2. "Number of banks per DIMM": One for single bank DIMM (i.e., DIMM equipped with Bank A only); two for dual bank DIMM (i.e., DIMM equipped with Bank A and Bank B). 3. x in MCER(x) = 0, 2, 4, or 6 4. a setting of “off” indicates that the bank must be disabled by setting MCER(x) Bit 0 = 0. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 181 of 209 IBM Dual Bridge and Memory Controller Error Handling The memory controller detects four errors: 1. Single-bit ECC 2. Multi-bit ECC 3. Invalid address 4. Overlapping memory extents Errors 2, 3, and 4 are considered hard errors. If one occurs, it is logged into MESR and MEAR and cannot be overwritten with a subsequent hard error. Single-bit ECC errors are considered soft and once logged into the MEAR and MESR, can be overwritten with a subsequent hard error. Single-Bit ECC Error, General Case The hardware procedure for this error is: 1. Set the single-bit error bit in the MESR register. 2. If neither a double-bit error nor an address error is present, store the syndrome in the MESR and the address in MEAR. 3. Corrected data is not written back to memory but forwarded to the requesting logic. 4. When Chip Programmability Register (PGCHP) bit 17 = 1, a Machine Check is performed to signal the processor that it could rewrite correct data to memory. Software must write zeros to the MESR to clear this error. If more than one single-bit ECC error occurs before the MESR clears, only the first error is recorded. When a double-bit ECC error or an address error occurs, the software overwrites the MESR and MEAR. Single-Bit ECC Error, Special Case For non-burst write transactions that do not span an entire aligned double-word, the Memory Controller performs a read-modify-write sequence to memory. If the read portion of the sequence results in a single-bit ECC error, the error is not logged into the MESR and MEAR for both the diagnostic and normal modes. However, the memory controller automatically writes corrected data to memory. Invalid Address Error An Invalid Address error is detected by the Memory Controller when an address does not match one of the eight configuration extents. The hardware procedure for this error is: 1. If no hard errors are in the MESR register, set the invalid address error bit. 2. If no hard errors are in the MEAR register, store the address. 3. In diagnostic mode, the Memory Controller responds with dummy data and indicates an Invalid Address error to the requesting logic. To enable further error logging, the software writes zeros into the MESR. When more than one address error occurs before the MESR clears, only the first error is recorded. No Singleor Double-Bit ECC errors are logged into the MESR and MEAR if they occur after the Invalid Address error. Double-Bit ECC Error, General Case The hardware procedure for this error is: Page 182 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller 1. Set the Double-Bit error bit in MESR if no hard errors are present. 2. Store the syndrome in MESR and the address in MEAR if no hard errors are present. 3. In normal mode, indicate the error to the requesting logic with DAT_ERR for the appropriate double word that failed in memory. 4. In diagnostic mode, do not indicate Double-Bit errors with DAT_ERR. 5. Software must write zeros to the MESR to clear errors. 6. If more than one Double-Bit error occurs before the MESR clears, only the first error is recorded. 7. A Single-Bit error is not logged into MESR and MEAR when it occurs after a Double-Bit error. 8. If an Address error occurs after a Double-Bit error, it is not be logged into MESR and MEAR. Double-Bit ECC Error, Special Case For non-burst write transactions that do not span an entire aligned double-word, the Memory Controller performs a read-modify-write sequence to memory. If the read portion of this sequence results in a Double-Bit error, the controller indicates the error to the requesting logic through the response bus instead of using DAT_ERR. If this occurs in diagnostic mode, the error is logged into MESR and MEAR, but not reported through the response bus. Overlapping Memory Extents Overlapping Memory Extents are not detected until an access occurs to an address mapped to two different configuration extents. When an overlap condition is detected, the hardware follows the following procedure: 1. Set the Overlapping Memory Extent error bit in MESR if no hard errors exist. 2. Store the address in MEAR if no hard errors exist. 3. The Memory Controller responds with dummy data for reads, ignores write data, and indicates an Invalid Address error to the requesting logic. To enable further error logging, the software writes zeros into the MESR. When a Single-bit or a hard error occurs after an Overlapping Memory Extent, the error is not logged into MESR and MEAR. CPC710_Mem.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 183 of 209 IBM Dual Bridge and Memory Controller Page 184 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Mem.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Bridges Overview The device’s PCI Bridge function executes load and store operations from the CPU to the PCI buses. It also provides an interface for PCI devices to access system memory. The PCI Bridge logic fully supports the PCI Local Bus Specification [2]. The following table describes the physical connections for PCI devices on the PCI-32 bus in a desktop system. PCI-32 Bus Device Physical Connection Example ARB Level RESET Signal IDSEL Signal1 PCI SLOT 0 P_REQ0/P_GNT0 P_RST IDSEL1 PCI SLOT 1 P_REQ1/P_GNT1 P_RST IDSEL2 PCI SLOT 2 P_REQ2/P_GNT2 P_RST IDSEL3 ETHERNET CHIP P_REQ3/P_GNT3 P_RST IDSEL4 SCSI CHIP P_REQ4/P_GNT4 P_RST IDSEL5 ISA BRIDGE CHIP P_REQ5/P_GNT5 P_RST IDSEL6 Not required POWERGOOD IDSEL7 Device MPIC 1. See External IDSEL Signal Logic for PCI-32 on page 191 for description of these signals Address Map There are two PCI bus bridges in the device. Both implement the register maps listed in the following table. The PCI Host Bridge Standard configuration space is Little Endian. PCI Bus Bridge Configuration Address Map Area System Standard Configuration Space Real Address Name Note x’FF20 0000’ DCR 1 Device Characteristics Register 137 x’FF20 0004’ DID 1 Device ID Register 138 x’FF20 0018’ BAR Base Address Reg. for Bridge Registers 139 x’FF20 001C’ to x’0FFF’ Device Specific Configuration Space x’FF20 1000’ x’FF20 1004’ to x’1FFF’ Use Page Reserved PCIENB PCI BAR Enable Register 140 Reserved 1. Read Only Register, write is ignored CPC710_Pci.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 185 of 209 IBM Dual Bridge and Memory Controller System Standard Configuration Registers System Standard Configuration Registers can only be accessed with 60x bus configuration cycles directed to a specific PCI bridge. Both of the device’s PCI bridges must be configured before any PCI configuration cycles can be issued. The registers provide a mechanism for firmware to identify the PCI bridge and the DCR and DID registers, and assign a 1 MB address space in the system memory map for the location of the PCI bridge facilities (BAR register). For detailed descriptions of these registers, refer to the following: • Device Characteristics Register (DCR) on page 137 • Device ID Register (DID) on page 138 • Base Address Register (BAR) on page 139 • PCI BAR Enable Register (PCIENB) on page 140 System PHB Registers The PCI bridge logic follows the PowerPC PCI Host Bridge (PHB) Architecture, including the enhanced error detection and error reporting features. The logic deviates from PHB Architecture only in its ability to recover from PCI errors. Page 186 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pci.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Bus Commands The following table describes the subset of PCI bus commands supported by the device. Supported PCI Commands C/BE[3:0] Command Support as Initiator Support as Target 0000 Interrupt Acknowledge Yes No 0001 Special Cycle Yes No 0010 I/O Read Cycle Yes No 0011 I/O Write Cycle Yes No 0100 Reserved 0101 Reserved 0110 Memory Read Yes Yes 0111 Memory Write Yes Yes 1000 Reserved 1001 Reserved 1010 Configuration Read Yes Yes (PCI-64 only) 1011 Configuration Write Yes Yes (PCI-64 only) 1100 Memory Read Multiple No Yes 1101 Dual Address Cycle No No 1110 Memory Read Line Yes Yes 1111 Memory Write and Invalidate Yes Yes CPC710_Pci.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 187 of 209 IBM Dual Bridge and Memory Controller PCI Master Memory Read Cycles When the device receives a memory read bus cycle from system memory, it first initiates a CLEAN cache operation to the processor bus. Processor accesses to this cache line are SYS_ARTRYed until the memory read is finished. If the cache line is determined to be stale in memory, the PCI bus cycle is retried. The following figure shows the states the device follows when executing a PCI memory read cycle. PCI Memory Read State Diagram Idle PCI Memory Read from system memory Initiate clean cache operation to the processor bus and start SYS_ARTRY of CPU access to this cache line Initiate read from system memory and stop SYS_ARTRY of CPU accesses to this line Wait for for operations to complete Cache line not modified in CPU Cache line is modified Retry PCI cycle Place memory read data on PCI bus to complete PCI transfer Page 188 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 FLUSH data in buffers CPC710_Pci.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Master Memory Write Cycles When the device receives a memory write bus cycle to system memory, it first initiates a FLUSH cache operation to the processor bus. Processor accesses to this cache line will be SYS_ARTRYed until the memory write is finished. If the cache line is determined to be stale in memory, the PCI bus cycle is retried. The following sequence describes the states the device follows when executing a PCI memory write cycle. PCI Memory Write State Diagram Idle PCI Memory Write to system memory Initiate FLUSH cache op to the processor bus and start SYS_ARTRY of CPU access to this cache line Wait for cache operation to complete Cache line is modified Cache line not modified in CPU Receive memory write data from PCI bus Stop SYS_ARTRY of CPU accesses Initiate write to system memory and stop SYS_ARTRY of CPU accesses to this line CPC710_Pci.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Retry PCI cycle Page 189 of 209 IBM Dual Bridge and Memory Controller Configuration Cycles The device implements Configuration Mechanism 1 as specified in the PCI Local Bus Specification [2]. This mechanism uses an indirect addressing model with the CONFIG_ADDRESS and CONFIG_DATA registers. The configuration target address is first written into CONFIG_ADDRESS and then an access is made to CONFIG_DATA to generate a configuration transfer. Each PCI bridge has a separate set of these registers. When each decodes an access to its CONFIG_DATA register, it performs different operations depending on the values stored in CONFIG_ADDRESS. PCI Configuration Cycle Matrix CONFIG_ADDRESS Register Fields Action Notes Enable Bus# Device# Function# Register# 0 x x x x Configuration not enabled. Returns 0’s on loads and ignores write data. 1 BUS# < BUSNO x x x Invalid Bus# in CONFIG_ADDR. Returns 1’s on loads and ignores store data. No access made to PCI Bus. 1, 2 0 0 x Access to PCI Bridge configuration space. Read/Write to PCI Bridge configuration registers. 1-21 x x Configuration access to device on PCI Bus. TYPE 0 configuration cycle on PCI bus. 22-30 x x Not supported. TYPE 0 configuration cycle with no IDSELs on. Returns 1s on loads and ignores store data. 31 7 0 Special cycle command. Special cycle command issued to PCI Bus. x x x Configuration access to bridge on PCI Bus. TYPE 1 configuration cycle on PCI Bus x Invalid bus# CONFIG_ADDR. Returns 1s on loads and ignores store data. No access made to PCI Bus. BUS# = BUSNO 1 BUS# > BUSNO BUS# < SUBNO BUS# > BUSNO BUS# > SUBNO x x 1, 2 1, 2, 3 1. Firmware must insure the SUBNO register in the PCI header is greater than or equal to the BUSNO register in the PCI header. Unpredictable results can occur if this is not true. 2. The PCI Bridge performs a compare of the BUS NUMBER field in the CONFIG_ADDRESS register and the BUS NUMBER field in the bridge’s 256-byte PCI header. 3. The PCI Bridge performs a compare of the BUS NUMBER field in the CONFIG_ADDRESS register and the SUBORDINATE BUS NUMBER field in the bridge’s 256-byte PCI header. If there is no response to a configuration cycle (no DEVSEL# detected), the device Master-Aborts the cycle, sets the Master Abort bit in the PCI Status register, and completes the processor cycle normally by returning all ones on reads and ignoring data on writes. TYPE 0 Configuration Cycles For TYPE 0 configuration cycles to devices on the PCI bus connected to the bridge, the IBM25CPC710AB3A100 indirectly supports up to eight separate IDSEL lines. It relies on external 3-8 decoders to provide a unique signal for each device on the bus. The IBM25CPC710AB3A100 drives external Page 190 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pci.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller address bits 13 through 11 (Little Endian) using the three PCI_CFG signals. It also drives PCI address/data bus bits 31 through 11 as shown in the following table. PCI Address/Data Bus for TYPE 0 Configuration Cycles 24 23 31 30 CONFIG_ADDRESS E Reserved 16 15 Bus Number 11 10 Device 87 21 0 Function Register No. 0 0 Decoded in the IBM25CPC710AB3A100 Function Register No. 0 0 Only One “1” 31 PCI Addr/Data Bus 11 10 Device = 1 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 Device = 2 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 Device = 3 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 0 1 0 0 0 Etc ....... The recommended external connection for the 3-8 decoders is shown below. PCI-32 Bus Device Physical Connection Example on page 185 describes a desktop example of system PCI device physical connections. External IDSEL Signal Logic for PCI-32 IBM25CPC710AB3A100 CONFIG_ADDRESS11 P_PCI_CFG0 CONFIG_ADDRESS12 P_PCI_CFG1 CONFIG_ADDRESS13 P_PCI_CFG2 3-8 Decoder 0 1 A 2 3 B 4 C 5 6 7 IDSEL0 IDSEL1 IDSEL2 IDSEL3 IDSEL4 IDSEL5 IDSEL6 IDSEL7 Not Connected See Device Table Type 1 Configuration Cycles For TYPE 1 configuration cycles, the IBM25CPC710AB3A100 directly copies the contents of the CONFIG_ADDRESS register to the Address/Data signals on the PCI bus. However, Address/Data[1:0] contains ’01’ to indicate a TYPE 1 configuration cycle. CPC710_Pci.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 191 of 209 IBM Dual Bridge and Memory Controller PCI Performance Estimates PCI to Memory Sustained Throughput Read Write Units PCI-64bit @ 66 MHz 91 121 MB/s PCI-32bit @ 33 MHz 53 58 MB/s Assumptions: • PCI Master parked on PCI bus • No other activity present • Adapter supports fast back-back transfers for stores to memory • No L1 or L2 cache hits CPU to PCI Sustained Throughput Loads @ 100 MHz Bus Operation Stores @ 100 MHz Bus Units PCI-32bit @ 33 MHz PCI-64bit @ 66 MHz PCI-32bit @ 33 MHz PCI-64bit @ 66 MHz Burst 32 bytes 71 194 71 194 MB/s Single 8 bytes 30 67 30 67 MB/s Single 4 bytes 17 33 17 33 MB/s Assumptions: • CPU is parked on 60x bus • 1 Level Pipeline • IBM25CPC710AB3A100 parked on PCI bus • No other activity present Page 192 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pci.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI Master Error Handling For PCI bus errors detected on CPU initiated transfers, refer to Error Handling for CPU-Initiated Transactions on page 162. The following table describes the error handling performed for PCI master errors. PCI Master Error Handling (Page 1 of 2) Operation Error Address Parity Error Mode Action Enabled by PCI CMND register bit 6 Save encoded arb level in CSR register Set Address parity error detected bit in CSR register Set Parity error detected bit 15 in PCI status register Place PCI address in PSEA register Activate SERR signal if enabled by bit 8 PCI CMND register Set Signalled SERR bit in PCI Status register if enabled Target abort PCI transfer if address matches Set Signaled target abort bit in PCI status register Signal Machine Check with SYS_MACHK Any PCI Bus Transfer Disabled Set Parity error detected bit 15 in PCI status register Complete PCI transfer normally if address matches Notes 1 Set Detected SERR active bit in CSR register Save encoded ARB level in CSR register Signal Machine Check with SYS_MACHK Detected SERR Active PCI Bridge Logic Idle Set single-bit error and syndrome in MESR Set error address in MEAR Return corrected data to PCI device Proceed normally with PCI transaction Single Bit Error Access to System Memory Normal Double Bit Error Diagnostic 1 Set double-bit error in MESR Set error address in MEAR Set memory error bit in CSR register Loads: - Target abort PCI transfer - Set signaled target abort bit in PCI status register - Signal Machine Check with SYS_MACHK Stores: - Signal Machine Check with SYS_MACHK Set double-bit error in MESR Set error address in MEAR Return uncorrected data to PCI device Proceed normally with PCI transaction 1 Notes: 1. “Normally” means that dummy zeros are returned for loads and write data is ignored. CPC710_Pci.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 193 of 209 IBM Dual Bridge and Memory Controller PCI Master Error Handling (Page 2 of 2) Operation Error Mode Set SERR detected error bit in CSR register Save encoded ARB level in CSR register Target abort PCI transfer Set signaled target abort bit in PCI status register Signal Machine Check with MACHK Detected SERR Active Detected PCI Bus Data Parity Error during PCI Master Store Enabled by PCI CMND register bit 6 Activate the PERR signal Set parity error bit 15 in PCI Status register Complete PCI transfer, however, Flush store data; do not write to memory Set parity error bit 15 in PCI Status register Proceed normally with PCI transaction 1 Detected PERR during PCI Master Load Proceed normally with PCI transaction 1 Received Master Abort Proceed normally with PCI transaction 1 PCI Bus Timeout: IRDY Count Expired Target abort PCI transfer Set signaled target abort bit in PCI status register Set PCI bus time-out error in CSR register Save encoded ARB level in CSR register Signal Machine Check with MACHK Internal Response Bus Contains “PCI Error” Status 2nd PCI bridge logs errors same as CPU initiated 2nd PCI bridge does NOT drive MACHK pin Set PCI - PCI error bit in CSR register Save encoded ARB level in CSR register Save PCI address in PSEA register Loads: - Target abort PCI transfer - Set signaled target abort bit in PCI status register - Signal Machine Check with MACHK Stores: - Signal Machine Check with MACHK Disabled Access to Device on 2nd PCI Bus Notes Set invalid address error in MESR Set error address in MEAR Set invalid memory address bit in CSR Loads: - Target abort PCI transfer - Set signaled target abort bit in PCI status register - Signal Machine Check with MACHK Stores: - Signal Machine Check with MACHK Invalid Address Access to System Memory (cont’d) Action Notes: 1. “Normally” means that dummy zeros are returned for loads and write data is ignored. Page 194 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pci.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller CPC710_Pci.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 195 of 209 IBM Dual Bridge and Memory Controller Page 196 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Pci.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller System I/O Interface The device implements a 2 MB ROM space from address 4G-2M to 4 GB. Configuration There is no configuration requirement for SIO logic. These areas are hard wired in the upper 16 MB of real memory. System I/O Registers: Application Presence Detect Bits The device provides Output Enables signals and read cycles for two external 32-bit registers. The read of the SIOR0 or SIOR1 results in a read of bits 0 to 31 of these register which correspond respectively to the data present on the line 31 and 0 of the PCI 32 bit A/D during the read cycle. For descriptions of these registers, refer to: • System I/O Register 0 (SIOR0) on page 127, controls PRES_OE0 signal • System I/O Register 1 (SIOR1) on page 128, controls PRES_OE1 signal • MCCR Register Settings on page 179 (for PD definition and the device’s supported values) Flash Interface and Presence Detect Bits Boot ROM The device’s Boot ROM base address is fixed at x’FFF0 0000’. Accesses to the architected Boot ROM space within the size limit defined in the System I/O Control Register (System I/O Control (SIOC) on page 103) are decoded as valid Boot ROM accesses. If the ROM Size parameter is larger than the actual amount of installed Boot ROM, the data will wrap. An access within the architected Boot ROM space but outside the size limit (SIOC x’FF00 1020’) results in a bus timeout Machine Check error. The Boot ROM interface logic satisfies burst read requests from the processor by concatenating multiple bytes from the Boot ROM. The device is designed to interface with 512 K, 1 Mb, 2Mb (x8) 3.3 V Flash memory with 80 to 120 ns access time. The following figure shows Boot Flash with the bits used for Address and Data on the PCI-32 bus AD lines. PCI AD bits 0:20 are used for Flash Address (LSB starts at bit 0). Bits [8:15] of the PCI-32 bus AD lines are used for the 8-bit data. The Boot Flash is accessed under control of the device’s PCI-32 controller to generate non-PCI cycles with FRAME not asserted. Flash is read and written by setting bit 4 (R/W) in the UCTL Register. CPC710_Sio.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 197 of 209 IBM Dual Bridge and Memory Controller Connection of Boot ROM and System I/O Registers (PD) to Device IBM 25C P C 710A B3A 100 X C V R _R D S IO _D [8: 15] D ir (see not e) PCI-32 BUS F 373 F _A D [19] CE F _A D [0: 18] P _A D L [31: 0] RE G W E OE L V T 245 X A D R _L A T F L A S H _O E OE F L A S H _W E W E St rap for Fl ash w rit e prot ect ion V CC CE BCT245 F _A D [0: 18] P R E S _O E 1 P D bit s 0[0: 31] 512 K x 8 F L A S H RE G 1 P R E S _O E 0 RE G 0 P D bit s 1[0: 31] P resence D et ect: 8 bit s/Bank N ot e: T here is no out putenabl e cont rolfort he L V T 245 drivers.A l lcont rolis done by t he D irect ion cont rolbit on signalX C V R _R D . P age 198 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 C P C 710_S io.fm .01 11/4/1999 IBM Dual Bridge and Memory Controller DMA Controller Introduction The DMA Controller controls data transfers between system memory and the PCI buses. Data can be transferred without DMA control only by gaining master access to a PCI bus. The controller runs with an elementary block of up to 4 KB. In Extended Mode, automatic chaining is performed during elementary DMA transfers. Up to 65,000 iterations can be programmed with address increments to transfer up to 256 MB of data in a single DMA. Address increments are performed after each DMA. An end-of-transfer DMA interrupt is raised only after multiple chained DMAs are complete. DMAs are initiated by either a eciwx (read) or ecowx (write) instruction from the processor and ended by an External Interrupt command. The controller uses an elementary burst of 32 Bytes on the PCI bus to facilitate interleaved PCI bus operations. The eciwx and ecowx instructions use the processor’s internal address translation logic to present real addresses on the system bus. This eliminates the need for external hardware to translate virtual addresses and for software to calculate real addresses. Because the DMA is virtual, no software overhead is required for pinning system memory that would otherwise be needed if the DMA operated in real address mode. Execution of an eciwx or ecowx instruction involves the same sequence as a normal cache inhibited load and store with a few exceptions. The processor calculates an effective address, translates it, and presents the resulting real address to the system bus as normal. However, this address bus does not select the slave. The address is passed to the slave to be used on a subsequent transfer. The slave is selected by a 4-bit Resource ID (RID) that is placed on the SYS_TBST and SYS_TSIZ[0:2] signals by the processor. The device is selected for these transactions when the RID on the bus matches Configuration Register bits 811 in the device’s System Control Register. The bus transaction is always a single beat regardless of the SYS_TBST signal setting. While the DMA is occurring, the device monitors the bus for a TLB Sync (resulting from normal page maintenance by the OS kernel) to terminate the transfer. Software can then restart the transfer at the faulting address. The DMA Controller transfers data between system memory and PCI only. It cannot perform memory-tomemory transfers. DMA operation is transparent to the PCI adapter, which behaves as a PIO slave device. Although eciwx and ecowx both initiate DMA, the preferred instruction is ecowx because it writes to the system bus. eciwx is provided to avoid access violation errors on pages marked read-only. Software ensures proper implementation of the DMA operation, including address alignments and page boundaries. The device aborts a DMA transfer when any of the following conditions are detected: • TLBSYNC operation detected (internal commands are completed before termination). • Improper DMA transfer setup. • Second DMA transfer initiated when one is already in progress. • The transfer crosses a page boundary. CPC710_Dma.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 199 of 209 IBM Dual Bridge and Memory Controller DMA Transfer Registers Several registers support the DMA transfer process. They are mapped to two different address spaces so the software can mark the x’FF1C xxxx’ range as user space and the ‘FF1E xxxx’ range as privileged space. This provides protection needed to allow the eciwx and ecowx instructions to be executed by application level software. The registers are listed in the following table and are described in DMA Registers Space on page 129. DMA Transfer Register Summary User Privileged Register Description Address Bits Mode Address Bits Mode GSCR FF1C 0020 [0:31] R FF1E 0020 [0:31] R/W Global Control Register GSSR FF1C 0030 [0:31] R FF1E 0030 [0:31] R Global Status Register XSCR FF1C 0040 [0:31] R/W FF1E 0040 [0:31] R/W DMA Transfer Control Register XSSR FF1C 0050 [0:31] R FF1E 0050 [0:31] R DMA Transfer Status Register [0:3] R [0:3] R/W XPAR FF1C 0070 [4:31] R FF1E 0070 [4:31] R/W PCI Address Register XWAR FF1C 0090 [0:31] R FF1E 0090 [0:31] R/W Writeback Address Register XTAR FF1C 00A0 [0:31] R FF1E 00A0 [0:31] R Translated Address Register The steps for executing a DMA transfer with software are: 1. Initialize XSCR to indicate length and direction of transfer. 2. Initialize XPAR with the PCI address. The PCI logic takes the address in the XPAR register and applies the translation as described in CPU to PCI Addressing Model (PREP and FPHB Modes) on page 144. 3. Initialize XWAR with the address to which the device writes to indicate status following transfer. 4. Clear cache line status in memory at address specified in XWAR. 5. Execute the ecowx instruction (or eciwx if read only page) to start transfer. 6. Wait until an End-of-DMA transfer interrupt (IT) occurs, then read the status on the memory address specified in XWAR. Reset bit 4 of the CSCR register to acknowledge the IT. Alternatively, perform cache polling to the memory address specified in XWAR and wait until the cache status flag changes from x’00’ to x’FF’. Page 200 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Dma.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller DMA Transfer Status Cache Line The following table shows the definition of the 64-bit of status stored in main memory at the address defined by the XWAR register. Only bits 32-63 of the second double-word of the Write Back Status cache line are valid. All other bytes in the cache line must be ignored. DMA Transfer Status Cache Line Definition Bit(s) Description Status Double-word 0 0-63 Reserved Status Double-word 1 0-63 Undefined Status Double-word 2 0-63 Undefined Status Double-word 3 0-31 32 - 39 x’0000 0000’ Poll Status Cache Line Valid Flag x’00’ - Initial value set by software. Indicates status cache line is not valid. x’FF’ - Written by hardware to indicate that the status cache line has been updated and is valid 40 Transfer Complete 0 - Transfer is not complete 1 - Transfer is complete 41 TLBSYNC Detected 0 - No TLBSYNC Detected 1 - TLBSYNC detected during DMA transfer Transfer 42 Reserved 43 Page Crossing Error 1 - Page Crossing detected during DMA transfer 44 Second DMA Transfer Halt 1 - DMA transfer operation in progress was halted due to start of second DMA transfer operation 45 Unaligned ecowx/eciwx Address 1 - Address associated with ECOWX/ECIWX is not word aligned 46 Unaligned Transfer Error 1 - Address alignment error 47 Address Increment Alignment Error 1 - Improper alignment of addresses when Address Increment bit is off 48 Invalid PCI Address 1- XPAR did not match any PCI extents 49 - 50 Reserved 51 - 63 Transfer Length This field contains the number of bytes remaining when the transfer was completed or aborted CPC710_Dma.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 201 of 209 IBM Dual Bridge and Memory Controller DMA Procedure The DMA transfer process begins when the 60x logic detects an ecowx or eciwx transaction on the processor bus. If the RID bits in the IBM25CPC710AB3A100 and System Control register match the RID bits on the SYS_TBST and SYS_TSIZ[0:2] lines, the 60x logic accepts the transfer. If the instruction is an ecowx, the 60x logic SYS_TAs the bus for dummy write data and sends a DMA Transfer Write command to the DMA Controller. The internal address bus associated with the Transfer Write command contains the address from the processor bus. This address is placed in the XTAR register by the DMA Controller. During the processor address tenure, the 60x logic sets an internal flag to indicate special handling of TLBSYNC operations on the processor bus. If the flag is not set, the 60x logic ignores all TLBSYNC operations on the processor bus. If the flag is set, a TLBSYNC operation on the bus causes the 60x logic to place a one cycle pulse on the UX6_TLB_SYNC line to the DMA Controller. The 60x logic continuously SYS_ARTRYs the TLBSYNC bus operation until it receives a one cycle pulse on the internal UXI_XFER_DONE line from the DMA Controller. This pulse also resets the 60x logic’s internal flag to perform special handling of the TLBSYNC operations. Note: Since the PowerPC601 processor does not issue TLBSYNC operations, the 60x logic must treat any SYNCs following a TLBI as a TLBSYNC operation when operating with a PowerPC601 processor. When the eciwx instruction is used, the 60x logic performs the same steps except that the 60x logic internally sends a DMA Transfer Read command to the DMA Controller and waits for a dummy read data response. The dummy read data is then placed on the processor bus to complete the eciwx transfer on the processor bus. The internal flag for special handling of TLBSYNC is set during the eciwx address bus tenure on the processor bus. After the DMA Controller receives the DMA Transfer command, it issues a Load Pointer command on the internal command bus to the appropriate PCI bus bridge logic unit. This transfers the address in XPAR to the PCI bus bridge pointer register. The DMA Controller then issues a series of Blit commands, or internal Elementary Commands from the DMA Controller to the PCI logic, to the same PCI bus bridge logic unit that transfers the data. The first Blit command contains the memory address stored in the XTAR register. The PCI bus bridge logic receives the Blit commands and then executes the transfer. For Blit Reads, the DMA Controller first determines whether the read from memory requires a snoop transaction. If the read is coherent, the controller issues a snoop command to the 60x logic. If the snoop fails, the controller retries the snoop until it passes. Once the snoop passes, a Blit Read command is transmitted to the PCI bus bridge logic. The PCI Bridge logic executes the command and then increments the value in its pointer register by the size of the transfer unless the Address Increment field in the Load Pointer command is set to No Increment. Blit Write commands are handled in same way except the transfer is from I/O to System Memory. Note: The DMA Controller should wait a minimum of eight cycles before reissuing snoop commands after a snoop fail response. After the transfer is complete, the controller signals the 60x logic by activating UXI_XFER_DONE for one cycle. The controller then issues a Write with Kill to the address specified in XWAR register to indicate to software that the transfer is complete. The controller issues a Kill Cache to the 60x logic, and upon receiving a clean response, issues a Write command to system memory. The write to memory need only be a single beat write to the bytes reserved for DMA transfer status. Page 202 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Dma.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Special Boundary Conditions Due to queueing in the 60x logic, a pulse could be placed on the TLBSYNC line to the DMA Controller before the controller receives an ecowx or eciwx. In this case, the controller waits until it receives an ecowx or eciwx and then immediately terminates the DMA transfer. When two DMA transfers overlap, the controller ignores the TLBSYNC pulse if a DMA transfer is nearly complete. However, because the 60x logic could have an eciwx or ecowx queued, the controller would have to remember the TLBSYNC pulse to terminate the second DMA transfer properly. To do this, the 60x logic indicates the presence of an eciwx or ecowx instruction in its queue to the controller. CPC710_Dma.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 203 of 209 IBM Dual Bridge and Memory Controller Page 204 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Dma.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Initialization Power Up Sequence The power up sequence for the device is: • At t=0 - All PLL inputs are stable and at their final values : PLL_TUNE0=0 , PLL_TUNE1=1 and TESTIN=0 SYS_CLK is stable at or below the target frequency VDDA and Vdd (supply) are at their final values - POWERGOOD input is asserted Low for Reset. - PLL_RESET input is asserted active (Low). - PCI clocks inputs (PCI_CLK and PCG_CLK) are stable at the target frequency • At t=1,000ns - PLL_RESET input is de-asserted inactive (High). - PLL_LOCK output is asserted active (High), indicating the PLL is locked. • At t=2,000ns - POWERGOOD input is de-asserted inactive (High). - Bus transactions may begin. Note: Chip reset is only controlled by the SYS_CLK. TESTIN is a manufacturing test input for the PLL. POWERGOOD Power-On Reset Using the system Power-On Reset POWERGOOD signal, the device resets internally and generates a reset signal to all CPUs and I/O devices. All device I/O pins go to tri-state. After a POWERGOOD cycle, outputs on all interfaces are either floating or driven to their inactive state, except for the reset signals sent to the board as described below. 1. PowerPC bus: HRESET0 and HRESET1 are driven Low for the same duration as the POWERGOOD active pulse (low level). 2. PCI-64 bus: G_RST is driven High from the beginning of the POWERGOOD assertion and remains active after POWERGOOD is deasserted. G_RST is deactivated when the processor writes a 1 into bit 0 of the, “Component Reset Register (CRR)” Page 69 - BAR + x’000F 7EF0’ for PCI-64. G_RST is deactivated within a period that complies with the PCI Specification [2] for the 64-bit interface. 3. PCI-32 bus: P_RST is driven Low from the beginning of the POWERGOOD assertion and remains active after POWERGOOD is deasserted. P_RST is deactivated when the processor writes a 1 into bit 0 of the, “Component Reset Register (CRR)” Page 69 - BAR + x’000F 7EF0’ for PCI-32 after several PCI clocks. CPC710_Init.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 205 of 209 IBM Dual Bridge and Memory Controller Typical Register setup sequence /** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * / /* T y picalC P C 710-100 regist ers set up sequence (from m odelsim ul at ion* / /* */ /* 11/17/99 IBM F rance */ /** * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * * / /* Begin C P C 710-100 regist ers set up sequence */ /*= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = * / /* 60X Int erface regist ers set up /* -----------------------------------------------* / R S T R (0x ff000010) U C T L (0x ff001000) A BC N T L (0x ff001030) E R R C (0x ff001050) S E S R (0x ff001060) S E A R (0x ff001070) P G C H P (0x ff001100) */ : w rit e 0x f0000000 : w rit e 0x 32f80000 : w rit e 0x b0000000 : w rit e 0x 00c00000 : w rit e 0x 00000000 : w rit e 0x 00000000 : w rit e 0x 00000000 /* M em ory Int erface regist ers set up /* ---------------------------------------------------* / M E S R (0x ff001220) M E A R (0x ff001230) M CE R 0(0x ff001300) M CE R 1(0x ff001310) M C C R (0x ff001200) */ : w rit e 0x 00000000 : w rit e 0x 00000000 : w rit e 0x 800080c0 : w rit e 0x 808080c0 : w rit e 0x 83b06000 /* PCI64 and PCI32 Int erfaces Configurat ion m ode set up * / /* ------------------------------------------------- * / /* E nabl e configurat ion m ode forPCI64 * / C N F R (0x ff00000c) : w rit e 0x 80000003 C P U S Y N C /* S Y N C O P * / BA R (0x ff200018) : w rit e 0x ff400000 PCIE N B(0x ff201000) : w rit e 0x 80000000 /* E nabl e configurat ion m ode forPCI32 * / C N F R (0x ff00000c) : w rit e 0x 80000002 C P U S Y N C /* S Y N C O P * / BA R (0x ff200018) : w rit e 0x ff500000 PCIE N B(0x ff201000) : w rit e 0x 80000000 /* D isabl e configurat ion m odes */ C N F R (0x ff00000c) : w rit e 0x 00000000 C P U S Y N C /* S Y N C O P * / /* PCI64 Int erface regist ers set up /* -------------------------------------------------* / P IBA R (0x ff4f7800) P M BA R PR ACR M S IZE IO S IZE */ : w rit e 0x 5c000000 : w rit e 0x 5a000000 : w rit e 0x 00008000 : w rit e 0x ff000000 : w rit e 0x fc000000 /*ex am pl e w it h 64 M B* / : w rit e 0x ff000000 /*ex am pl e w it h 16 M B* / P age 206 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 C P C 710_Init .fm .01 11/4/1999 IBM Dual Bridge and Memory Controller S M BA R S IBA R CSR PL SSR : w rit e 0x e0000000 : w rit e 0x 90000000 : w rit e 0x 00000000 : w rit e 0x 00000000 /* PCI64 Com m and regist erset up * / CF G A (0x ff4f8000) : w rit e 0x 04000080 CF G D (0x ff4f8010) : w rit e 0x 5601 /* P C I32 Int erface regist ers set up /* -------------------------------------------------* / P IBA R (0x ff5f7800) P M BA R PR ACR M S IZE IO S IZE S M BA R S IBA R CSR PL SSR BP M D L K TPM D L K BIO D L K T IO D L K */ : w rit e 0x 1c000000 : w rit e 0x 1a000000 : w rit e 0x 0000c000 : w rit e 0x fe000000 : w rit e 0x fe000000 /*ex am pl e w it h 32 M B* / : w rit e 0x ff800000 /*ex am pl e w it h 8 M B* / : w rit e 0x c0000000 : w rit e 0x 80000000 : w rit e 0x 00000000 : w rit e 0x 00000000 : w rit e 0x c0400000 : w rit e 0x c0800000 : w rit e 0x 80400000 : w rit e 0x 80800000 /* PCI32 Com m and regist erset up * / CF G A (0x ff5f8000) : w rit e 0x 04000080 CF G D (0x ff5f8010) : w rit e 0x 5601 /* -------------------------------------------------* / /* W aitforS D R A M init ial iz at ion is com pl et e --> M CCR (2)goes t o a 1 */ /* R el ease ex t ernalresett o PCI32 bus agent s */ C R R (0x ff5f7ef0) : w rit e 0x fc000000 /* R el ease ex t ernalresett o PCI64 bus agent s */ C R R (0x ff4f7ef0) : w rit e 0x fc000000 /* E nd of CPC710-100 regist ers set up sequence * / /*= = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = = * / C P C 710_Init .fm .01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 P age 207 of 209 IBM Dual Bridge and Memory Controller Page 208 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Init.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Timing Diagrams CPU to Memory Read Page Hit from PowerPC CPU to SDRAM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 CLK100MHz SYS_ADDR SYS_TS SYS_TA SYS_DATA 1 2 3 4 MUX_MDATA MEM_DATA DH D1 D3 MEM_DATA DL D2 D4 MEM_STATUS activ. Burst=4 CAS Lat=2 prech. MADDR SDRAS SDCAS WE SDDQM SDCKE 1 CPC710_Chronos.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 2 3 4 Page 209 of 209 IBM Dual Bridge and Memory Controller Read Page Miss from PowerPC CPU to SDRAM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 CLK100MHz SYS_ADDR SYS_TS SYS_TA 1 2 SYS_DATA 1 2 MUX_MDATA MEM_DATA DH D1 D3 MEM_DATA DL D2 D4 MEM_STATUS activ. Burst=4 prech. 3 3 4 4 activ. prech. MADDRESS SDRAS SDCAS WE SDDQM SDCKE Burst=4 CAS Lat=2 1 2 3 4 Page 210 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Chronos.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Write Burst Page Hit from PowerPC CPU to SDRAM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 CLK100MHz SYS_ADDR Ad1,2,3,4 SYS_TS SYS_TA SYS_DATA 1 2 3 4 MUX_MDATA 5 6 7 8 1 2 3 4 5 MEM_DATA DH D1 D3 MEM_DATA DL D2 D4 MEM_STATUS activ. 6 Burst=4 CAS Lat=2 7 8 prech. MADDR SDRAS SDCAS WE SDDQM SDCKE Write 1& 2 CPC710_Chronos.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Write 3&4 Page 211 of 209 IBM Dual Bridge and Memory Controller Write Burst Page Miss from PowerPC CPU to SDRAM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 CLK100MHz SYS_ADDR SYS_TS SYS_TA SYS_DATA MUX_MDATA 3 4 1 2 3 4 1 2 3 4 MEM_DATA DH D1 D3 MEM_DATA DL D2 D4 MEM_STATUS activ. Burst=4 CAS Lat=2 prech. activ. prech. MADDR SDRAS SDCAS WE SDDQM SDCKE Write 1& 2 Page 212 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 3&4 CPC710_Chronos.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller Write One Byte to Memory from CPU: Read Modify Write 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 CLK100MHz SYS_ADDR SYS_TS SYS_TA SYS_DATA MUX_MDATA DW-0 MEM_DATA DW-0 Modified DW-0 Modified DW-0 MADDR MEM_STATUS Activ Read Write Prech SDRAS SDCAS WE CAS Latency = 3 SDDQM SDCKE CPC710_Chronos.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 213 of 209 IBM Dual Bridge and Memory Controller CPU Access to the Boot ROM Read of One Byte from the Boot ROM 0 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 CLK100MHz A1 SYS_ADDR 1 SYS_TSIZ SYS_TS SYS_TA SYS_DATA A1 PCI_AD[31:0] Byte1 xxx > 80 ns XADR_LAT FLASH_OE XCVR_RD Write of One Byte to the Boot Flash CLK100MHz Code 1 2 3 Data FFF05555 FFF02AAA FFF05555 FFF02000 SYS_ADDR SYS_TSIZ 1 1 1 1 SYS_TS SYS_TA SYS_DATA Code 1 A1 PCI_AD[31:0] Code1 XADR_LAT FLASH_WE XCVR_RD Write of the Data in the flash after the 4th WE 01 10 Page 214 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 20 30 40 50 60 CPC710_Chronos.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller PCI-64 external Master accessing the SDRAM Memory READ 32 Bytes from the SDRAM by a PCI Master on PCI 64- 66MHz bus: CLK100MHz MDATA SDRAM_DH 1 3 2 4 12 5 6 SDRAM_DL 34 5 7 6 8 78 MADDR RAS Read CAS Precharge WE CKE 66MHz Clock CBE[7:0] 00 PCI_AD[63:32] 00 Z 00 fffffffff PCI_AD[31:0] Add 32-bit Word 1 3 5 7 32-bit Word 2 4 6 8 00 Z fffffffff Add G_FRAME G_IRDY G_TRDY G_STOP 0 1 10 20 30 40 50 Note: 1,2,3 .. refers to 1st 2nd third 32-bit word. READ the SDRAM from a PCI Master on PCI 64 CPC710_Chronos.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 215 of 209 IBM Dual Bridge and Memory Controller Write of 32 Bytes in the SDRAM from a PCI Master on the PCI 64- 66MHz bus CLK100MHz 12 34 56 MDATA SDRAM_DH 12 56 SDRAM_DL 34 78 78 MADDR RAS Write CAS Precharge WE CKE 66MHz Clock CBE[7:0] 00 00 PCI_AD[63:32] fffffffff 32-bit Word 1 3 5 7 PCI_AD[31:0] 32-bit Word 2 Data 4 6 Add 00 fffffffff 8 Add G_FRAME G_IRDY G_TRDY G_STOP 0 1 10 20 30 40 50 WRITE to the SDRAM from a PCI Master on PCI 64 Page 216 of 209 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Chronos.fm.01 11/4/1999 IBM Dual Bridge and Memory Controller CPC710_Chronos.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 217 of 209 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Electrical Specifications Absolute Maximum Ratings Symbol Parameter Min Max Units VDD Supply Voltage 0 3.6 V VIN Input Voltage 0 3.6 V TSTG Storage Temperature Range -65 150 °C Recommended DC Operating Conditions Symbol Parameter Min Typ Max Units VDD Supply Voltage 3.135 3.3 3.465 V VIH Input Logic High (3.3 V receivers) 2.0 VDD V VIH Input Logic High (5.0 V receivers) 2.0 5.0 V VIL Input Logic Low 0.0 0.8 V VOH Output Logic High 2.4 VDD V VOL Output Logic Low 0.0 0.4 V IIL1 Input Leakage Current 10 µA VIMAO3 Input Max Allowable Overshoot (3.3 V receivers) VDD + 0.6 V VIMAO5 Input Max Allowable Overshoot (5.0 V receivers) 5.5 V VIMAU3 Input Max Allowable Undershoot (3.3 V receivers) -0.6 V VIMAU5 Input Max Allowable Undershoot (5.0 V receivers) -0.6 V VOMAO3 Output Max Allowable Overshoot (3.3 V receivers) VDD + 0.6 V VOMAO5 Output Max Allowable Overshoot (5.0 V receivers) 5.5 V VOMAU3 Output Max Allowable Undershoot (3.3 V receivers) -0.6 V TJ Die Junction Temperature 105 °C Page 218 of 225 Powered by ICminer.com Electronic-Library Service CopyRight 2003 <1 -20 CPC710_Acdc.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Driver/Receiver Specifications DC Voltage Specifications Driver/Receiver Function MAUL (V) MPUL (V) LPUL (V) MPDL (V) LPDL (V) MADL (V) Notes 3.3 V LVTTL Driver TTL VDD +0.6 V VDD (3.0 V to 3.6 V) 2.40 0.40 0.00 -0.60 1 5.0 V- tolerant LVTTL Driver TTL 5.50 VDD 2.40 0.40 0.00 -0.60 1 3.3 V LVTTL Receiver TTL VDD +0.6 V VDD 2.00 0.80 0.00 -0.60 1 5.0 V- tolerant LVTTL Receiver TTL 5.50 5.50 2.00 0.80 0.00 -0.60 1 1. Definition of Terms: MAUL Maximum Allowable Up Level. The maximum voltage that may be applied without affecting the specified reliability. Cell functionality is not implied. Maximum Allowable applies to overshoot only. MPUL Maximum Positive Up Level. The most positive voltage that maintains cell functionality. The maximum positive logic level. LPUL Least positive Up Level. The least positive voltage that maintains cell functionality. The minimum positive logic level MPDL Most Positive Down Level. The most positive voltage that maintains cell functionality. The maximum positive logic level. LPDL Least positive Down Level. The least positive voltage that maintains cell functionality. The minimum positive logic level MADL Minimum Allowable Down Level. The minimum voltage that may be applied without affecting the specified reliability. Cell functionality is not implied. Minimum Allowable applies to undershoot only. LVTTL Driver Minimum DC Currents at Rated Voltage (VDD at 3.0 V, temperature at 100 °C) Driver Type VHI (V) IHI (mA) VLO (V) ILO (mA) 50 Ohm Driver Outputs 2.40 11.0 0.40 7.0 Thermal Specifications Parameter Typ Max Units 2.1 2.7 Watts No Air Flow 18.1 - °C/Watt 100 CFM 16.9 - °C/Watt No Air Flow + Cap 12.6 - °C/Watt No Air Flow + 4.5mm Heat Sink 6.0 - °C/Watt Power Dissipation Thermal Resistance (from junction to air) CPC710_Acdc.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 219 of 225 IBM Dual Bridge and Memory Controller IBM Preliminary Draft AC Timing Specifications VCC = 3.3 V ±5%, Tj = - 20 °C to +105 °C 60x Bus Timings 60x Bus Inputs 9q-604e Timing IBM25CPC710AB3A100 Signal 8p-750 Timing Setup (ns) Hold (ns) Tp max (ns) 50 pf Tp min (ns) 0 pf Tp max (ns) 50 pf Tp min (ns) 0 pf SYS_BR[0:1] 5.2 0.0 5.75 0.50 5.00 1.00 SYS_TS, SYS_ARTRY, SYS_TBST 5.2 0.0 4.75 0.50 4.50 1.00 Others 4.6 0.0 5.75 0.50 5.00 1.00 60x Bus Outputs Output Valid Output Hold Signal 9q-604e Timing (0 to 105 °C) 8p-750 Timing Max (ns) Load (pf) Min (ns) Load (pf) Setup (ns) Hold (ns) Setup (ns) Hold (ns) SYS_ADDR[0:31] 6.9 30 pf 1.5 10 pf 2.5 - 0.5 2.5 + 0.6 SYS_DATA[0:63] 7.5 30 pf 1.7 10 pf 2.5 - 0.5 2.5 + 0.6 DATAP[0:7] 6.5 30pf 1.1 10pf 2.5 - 0.5 2.5 + 0.6 SYS_ARTRY, SYS_SHD, SYS_AACK , SYS_BG[0:1], DBG[0:1], SYS_TA, SYS_TEA 6.9 30 pf 1.2 10 pf 3.5 - 0.5 2.5 + 0.6 CHKSTOP, SYS_GBL, SYS_HRESET[0:1], SYS_MACHK[0:1], SRESET[0:1], SYS_TBE, SYS_TBST, SYS_TSIZ[0:2], SYS_TT[0:4] 7.4 30 pf 1.3 10 pf 2.5 - 0.5 2.5 + 0.6 Page 220 of 225 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Acdc.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft PCI Bus Timings 33 MHz PCI-32 Bus IBM25CPC710AB3A100 PCI Spec Description Units Min Max Min Max Output Valid - Bused Signals 3 10 2 11 ns Output Valid - Point To Point 3 11 2 12 ns Input Hold -0.3 0 ns Input Setup - Bused Signals 6.5 7 ns Input Setup - GNT# NA 10 ns Input Setup - REQ# 4.5 12 ns Clock Skew 2 System Prop 10 66 MHz PCI 64 Bus AC Timing Specifications IBM25CPC710AB3A100 PCI Spec Description Units Min Max Min Max Output Valid - Bused Signals 2.1 6.9 2 6 ns Output Valid - Point To Point 6 6 2 6 ns Input Hold -0.3 0 ns Input Setup - Bused Signals 3.1 3 ns Input Setup - GNT# 4.7 5 ns Input Setup - REQ# 4.7 5 ns Clock Skew 1 System Prop 5 CPC710_Acdc.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 221 of 225 IBM Dual Bridge and Memory Controller IBM Preliminary Draft SDRAM Interface Timings SDRAM Input Timing Specifications Signal MDATA[0:71] Setup (ns) Hold (ns) tRISE/tFALL max (V/ns) tRISE/tFALL min (V/ns) 3.0 0.1 2.0 0.50 SDRAM Output Timing Specifications Max output delays (ns) versus load capacitance (pf) Signal 10 20 30 40 50 60 70 80 90 100 110 120 SDCS[0:15]/ SDCS[0:7] & 8 x SDDQM 4.0 4.8 5.6 6.4 7.2 8.0 8.8 9.6 10.3 11.1 − − 8 x SDCKE − − 5.2 6.0 6.7 7.6 8.3 9.1 9.9 10.7 11.5 12.3 4 x SDRAS 4 x SDCAS 4 x WE − − 8.2 9.0 9.8 10.5 11.3 − − − − BS[0:1] MADDRLSB MADDR[1:12] − 7.8 8.6 9.4 10.2 11.0 11.8 12.6 13.4 14.2 − − CLKEN1B CLKEN2B CLKENA1 CLKENA2 − 6.5 7.2 8.0 − − − − − − − − MUX_OEA/OEB − 6.4 7.1 7.9 − − − − − − − − MUX_SEL − 8.0 8.8 9.6 − − − − − − − − 5.9 6.7 7.4 − − − − − − − − − MDATA[0:71] Page 222 of 225 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Acdc.fm.01 11/4/1999 IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller IBM Preliminary Draft Packaging Information Package Dimensions 32.5mm BGA - Standard JEDEC 32.5 0.2mm 30.48 0.2mm 25 25 x 25 Pad Array 624 Total pads 480 Signal I/Os 116 Power 20 Test 8 No Connect 32.5 30.48 01 Decoupling Capacitance 47nF Device 9.0mm x 9.05mm Ceramic Substrate C4 Encapsulant fillet 2.78mm 1.05mm 0.87mm 1.27mm 0.9mm All measurements are in millimeters unless otherwise noted. Drawing is not to scale. CPC710_Acdc.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 223 of 225 IBM Dual Bridge and Memory Controller IBM Preliminary Draft References 1. PC SDRAM Specification, Revision 1.63. October 1998, Intel 2. PCI Local Bus Specification, Revision 2.1. June 1st 1995, PCI Special Interest Group Page 224 of 225 Powered by ICminer.com Electronic-Library Service CopyRight 2003 CPC710_Acdc.fm.01 11/4/1999 IBM Preliminary Draft IBM25CPC710AB3A100 IBM Dual Bridge and Memory Controller Revision Log Revision Date Contents of Modification 09/08/99 Initial release (00) 12/17/99 release (1.0) - PCI 64 REQ setting to disable arbiter - XATS removed - P_ISA_MASTER must be tied to GND to be inactive - Initialization: PowerUp at time 0 - SOI1 & SOI2 space access: unpredictable results (See UCTL Register) - ATAS init programing value for PowerPC750 Memory/Cache coherency - Firecoral replaced by PCI-ISA bridge - Boot ROM data on PCI AD[8:15] - Access to SDRAM from PCI or CPU performed in rotating priority - MADDR0 LSB split in MADDR0_ODD & MADDR1_EVEN - G_CBE[0:7] & P_CBE[0:3] active low - CMND Reg reset values reversed - MCER Reg extended code bank for 4 & 8 MB - PCI to PCI transfers: unpredictable results: PPSIZE & BARPP & PPBAR Regs removed - POWERGOOD Active high (Reset when low) - SIOR0 & SIOR1 registers controls PRES_OE0 & PRES_OE1 signals - External Mux control signals renamed - Temperature range: -20 to 105 C - Read and write Waveforms for the PCI 64 -66MHz access to the memory - Typical Register Setup sequence - P_LOCK & G_LOCK are Input only - LOCK on PCI busses not fully supported - MCER0 to 7 address corrected CPC710_Acdc.fm.01 11/4/1999 Powered by ICminer.com Electronic-Library Service CopyRight 2003 Page 225 of 225