1CY7C235A CY7C235A 1K x 8 Registered PROM Features • Capable of withstanding greater than 2001V static discharge • CMOS for optimum speed/power • High speed — 25 ns address set-up Functional Description The CY7C235A is a high-performance 1024-word by 8-bit electrically programmable read only memory packaged in a slim 300-mil plastic or hermetic DIP, 28-pin leadless chip carrier, or 28-pin plastic leaded chip carrier. The memory cells utilize proven EPROM floating gate technology and byte-wide intelligent programming algorithms. — 12 ns clock to output • Low power — 495 mW (Commercial) — 660 mW (Military) Synchronous and asynchronous output enables On-chip edge-triggered registers Programmable asynchronous registers (INIT) EPROM technology, 100% programmable Slim, 300-mil, 24-pin plastic or hermetic DIP or 28-pin LCC and PLCC • 5V ±10% VCC, commercial and military • TTL-compatible I/O • Direct replacement for bipolar PROMs The CY7C235A replaces bipolar devices pin for pin and offers the advantages of lower power, superior performance, and high programming yield. The EPROM cell requires only 12.5V for the supervoltage, and low current requirements allow for gang programming. The EPROM cells allow for each memory location to be tested 100%, as each location is written into, erased, and repeatedly exercised prior to encapsulation. Each PROM is also tested for AC performance to guarantee that the product will meet AC specification limits after customer programming. • • • • • Logic Block Diagram Pin Configuration DIP Top View INIT O7 A9 O6 ROW ADDRESS A7 PROGRAMMABLE ARRAY MULTIPLEXER PROGRAMMABLE INITIALIZE WORD A8 A6 A5 ADDRESS DECODER A4 A3 O5 8-BIT EDGETRIGGERED REGISTER O4 O3 A2 A7 A6 A5 A4 A3 A2 A1 A0 O0 O1 O2 GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC A8 A9 E INIT ES CP O7 O6 O5 O4 O3 O2 COLUMN ADDRESS LCC/PLCC Top View O1 A5 A6 A7 NC V CC A8 A9 A1 A0 O0 CP 4 3 2 1 2827 26 25 5 24 6 23 7 22 8 21 9 20 10 19 11 12 1314151617 18 A4 A3 A2 A1 A0 NC O0 CP ES O1 O2 GND NC O3 O4 O5 E E INIT ES CP NC O7 O6 Selection Guide 7C235A-25 25 12 90 Minimum Address Set-Up Time Maximum Clock to Output Maximum Operating Commercial Current Military Cypress Semiconductor Corporation Document #: 38-04002 Rev. *B • 3901 North First Street 7C235A-30 30 15 90 • San Jose 7C235A-40 40 20 90 120 • Unit ns ns mA mA CA 95134 • 408-943-2600 Revised December 27, 2002 CY7C235A DC Input Voltage ................................................. −3.0V to +7.0V Maximum Ratings[1] (Above which the useful life may be impaired. For user guidelines, not tested.) Storage Temperature ..................................... −65°C to +150°C Ambient Temperature with Power Applied.................................................. −55°C to +125°C DC Program Voltage (Pins 7, 18, 20 for DIP) ............... 13.0V Static Discharge Voltage............................................ >2001V (per MIL-STD-883, Method 3015) Latch-Up Current..................................................... >200 mA Operating Range Supply Voltage to Ground Potential (Pin 24 to Pin 12 for DIP) .................................. −0.5V to +7.0V DC Voltage Applied to Outputs in High Z State .................................................... −0.5V to +7.0V Ambient Temperature Range Commercial Military[2] VCC 0°C to +70°C 5V ±10% −55°C to +125°C 5V ±10% Electrical Characteristics Over Operating Range[3] Parameter Description Test Conditions Min. VOH Output HIGH Voltage VCC = Min., IOH = −4.0 mA VIN = VIH or VIL VOL Output LOW Voltage VCC = Min., IOL = 16 mA VIN = VIH or VIL VIH Input HIGH Level Guaranteed Input Logical HIGH Voltage for All Inputs[4] VIL Input LOW Level Guaranteed Input Logical LOW Voltage for All Inputs[4] IIX Input Leakage Current GND < VIN < VCC VCD Input Clamp Diode Voltage Note 5 IOZ Output Leakage Current IOS ICC Max. Unit 2.4 V 0.4 V 2.0 V 0.8 V −10 +10 µA GND < VOUT < VCC Output Disabled[4] −10 +10 µA Output Short Circuit Current VCC = Max., VOUT = 0.0V[6] −20 −90 mA Power Supply Current IOUT = 0 mA, VCC = Max. Commercial 90 mA Military 120 VPP Programming Supply Voltage IPP Programming Supply Current VIHP Input HIGH Programming Voltage VILP Input LOW Programming Voltage 12 13 V 50 mA 3.0 V 0.4 V Capacitance[5] Parameter CIN COUT Description Input Capacitance Output Capacitance Test Conditions TA = 25°C, f = 1 MHz, VCC =5.0V Max. 10 10 Unit pF pF Notes: 1. The volatge on any input or I/O pin cannot exceed the power pin during power-up. 2. TA is the “instant on” case temperature. 3. See the last page of this specification for Group A subgroup testing information. 4. For devices using the synchronous enable, the device must be clocked after applying these voltages to perform this measurement. 5. See Introduction to CMOS PROMs in this Data Book for general information on testing. 6. For test purposes, not more than one output at a time should be shorted. Short circuit test duration should not exceed 30 seconds. Document #: 38-04002 Rev. *B Page 2 of 10 CY7C235A a AC Test Loads and Waveforms[5] R1 250Ω 5V R1 250Ω 5V OUTPUT 50 pF R2 167Ω (a) NormalLoad Equivalent to: 5 pF R2 167Ω INCLUDING JIG AND SCOPE INCLUDING JIG AND SCOPE ALL INPUT PULSES 3.0V OUTPUT 90% 10% GND ≤ 5 ns 90% 10% ≤ 5 ns (b) High -ZLoad THÉVENIN EQUIVALENT 100Ω OUTPUT 2.0V Operating Modes The CY7C235A incorporates a D-type, master-slave register on chip, reducing the cost and size of pipelined microprogrammed systems and applications where accessed PROM data is stored temporarily in a register. Additional flexibility is provided with synchronous (ES) and asynchronous (E) output enables and asynchronous initialization (INIT). Upon power-up, the synchronous enable (ES) flip-flop will be in the set condition causing the outputs (O0−O7) to be in the OFF or high-impedance state. Data is read by applying the memory location to the address input (A0−A9) and a logic LOW to the enable (ES) input. The stored data is accessed and loaded into the master flip-flops of the data register during the address set-up time. At the next LOW-to-HIGH transition of the clock (CP), data is transferred to the slave flip-flops, which drive the output buffers, and the accessed data will appear at the outputs (O0−O7), provided the asynchronous enable (E) is also LOW. The outputs may be disabled at any time by switching the asynchronous enable (E) to a logic HIGH, and may be returned to the active state by switching the enable to a logic LOW. Regardless of the condition of E, the outputs will go to the OFF or high-impedance state upon the next positive clock edge after the synchronous enable (ES) input is switched to a HIGH level. If the synchronous enable pin is switched to a logic LOW, the subsequent positive clock edge will return the output to the active state if E is LOW. Following a positive clock edge, the address and synchronous enable inputs are free to change since no change in the output will occur until the next LOW-to-HIGH transition of the clock. This unique feature allows the CY7C235A decoders and sense amplifiers to access the next location while previously addressed data remains stable on the outputs. Document #: 38-04002 Rev. *B System timing is simplified in that the on-chip edge-triggered register allows the PROM clock to be derived directly from the system clock without introducing race conditions. The on-chip register timing requirements are similar to those of discrete registers available in the market. The CY7C235A has an asynchronous initialize input (INIT). The initialize function is useful during power-up and time-out sequences and can facilitate implementation of other sophisticated functions such as a built-in “jump start” address. When activated the initialize control input causes the contents of a user programmed 1025th 8-bit word to be loaded into the on-chip register. Each bit is programmable and the initialize function can be used to load any desired combination of 1s and 0s into the register. In the unprogrammed state, activating INIT will generate a register CLEAR (all outputs LOW). If all the bits of the initialize word are programmed, activating INIT performs a register PRESET (all outputs HIGH). Applying a LOW to the INIT input causes an immediate load of the programmed initialize word into the master and slave flip-flops of the register, independent of all other inputs, including the clock (CP). The initialize data will appear at the device outputs after the outputs are enabled by bringing the asynchronous enable (E) LOW. When power is applied the (internal) synchronous enable flip-flop will be in a state such that the outputs will be in the high-impedance state. In order to enable the outputs, a clock must occur and the ES input pin must be LOW at least a set-up time prior to the clock LOW-to-HIGH transition. The E input may then be used to enable the outputs. When the asynchronous initialize input, INIT, is LOW, the data in the initialize byte will be asynchronously loaded into the output register. It will not, however, appear on the output pins until they are enabled, as described in the preceding paragraph. Page 3 of 10 CY7C235A Switching Characteristics Over Operating Range[3, 5] 7C235A-25 Parameter Description Min. Max. 7C235A-30 Min. Max. 7C235A-40 Min. Max. Unit tSA Address Set-Up to Clock HIGH 25 30 40 ns tHA Address Hold from Clock HIGH 0 0 0 ns tCO Clock HIGH to Valid Output tPWC Clock Pulse Width 12 15 20 ns tSES ES Set-Up to Clock HIGH 10 10 15 ns tHES ES Hold from Clock HIGH 5 5 5 ns tDI Delay from INIT to Valid Output tRI INIT Recovery to Clock HIGH 20 tPWI INIT Pulse Width 20 tCOS Inactive to Valid Output from Clock HIGH[7] 12 15 25 HIGH[7] 20 25 ns 35 20 ns 20 20 ns 25 ns 20 20 25 ns 20 20 25 ns tHZC Inactive Output from Clock tDOE Valid Output from E LOW 20 20 25 ns tHZE Inactive Output from E HIGH 20 20 25 ns Note: 7. Applies only when the synchronous (ES) function is used. Switching Waveforms[5] tHA tSA tHA tHES tSES tHES A0 − A10 ES tSES CP tPWC O0 − O7 tCO tHES tPWC tHZC tSES tPWC tPWC tCOS tPWC tPWC tCO tHZE tDOE E tDI tRI INIT tPWI Programming Information Programming support is available from Cypress as well as from a number of third-party software vendors. For detailed Document #: 38-04002 Rev. *B programming information, including a listing of software packages, please see the PROM Programming Information located at the end of this section. Programming algorithms can be obtained from any Cypress representative. Page 4 of 10 CY7C235A Table 1. Mode Selection Pin Function[8] Read or Output Disable A0, A3−A9 A1 A2 CP ES E INIT O7−O0 Other A0, A3−A9 A1 A2 PGM VFY E VPP D7−D0 Read A0, A3−A9 A1 A2 X VIL VIL VIH O7−O0 Output Disable A0, A3−A9 A1 A2 X VIH X VIH High Z Output Disable A0, A3−A9 A1 A2 X X VIH VIH High Z Initialize A0, A3−A9 A1 A2 X X VIL VIL Init Byte Program A0, A3−A9 A1 A2 VILP VIHP VIHP VPP D7−D0 Program Verify A0, A3−A9 A1 A2 VIHP VILP VIHP VPP O7−O0 Program Inhibit A0, A3−A9 A1 A2 VIHP VIHP VIHP VPP High Z Intelligent Program A0, A3−A9 A1 A2 VILP VIHP VIHP VPP D7−D0 Program Initialize Byte A0, A3−A9 VPP VILP VILP VIHP VIHP VPP D7−D0 Blank Check A0, A3−A9 A1 A2 VIHP VILP VIHP VPP Zeros Mode Note: 8. X = “don’t care” but not to exceed VCC ±5%. GND 1 2 3 4 5 6 7 8 9 10 11 12 24 23 22 21 20 19 18 17 16 15 14 13 VCC A8 A9 E VPP VFY PGM D7 D6 D5 D4 D3 A4 A3 A2 A1 A0 NC D0 5 6 7 8 9 10 11 4 3 2 1 28 27 26 25 24 23 22 21 20 19 121314151617 18 E VPP VFY PGM NC D7 D6 D1 D2 GND NC D3 D4 D5 A7 A6 A5 A4 A3 A2 A1 A0 D0 D1 D2 LCC/PLCC Top View A5 A6 A7 NC VCC A8 A9 DIP Top View Figure 1. Programming Pinouts Document #: 38-04002 Rev. *B Page 5 of 10 CY7C235A NORMALIZED SUPPLY CURRENT vs. AMBIENT TEMPERATURE NORMALIZED SUPPLY CURRENT vs. SUPPLY VOLTAGE 1.2 1.4 NORMALIZED ICC 1.2 1.0 TA =25°C f = fMAX 0.8 0.6 4.0 4.5 5.0 5.5 1.1 1.0 0.9 0.8 −55 6.0 1.2 1.0 0.8 125 1.0 0.8 0.6 TA =25°C 0.4 4.0 AMBIENT TEMPERATURE (°C) 4.5 5.0 5.5 VCC =5.5V TA =25°C TYPICAL ACCESS TIME CHANGE vs. OUTPUT LOADING DELTA t AA (ns) 25.0 0.96 0.94 0.92 20.0 15.0 10.0 TA =25°C VCC =4.5V 5.0 0.90 0 25 50 75 CLOCK PERIOD (ns) 1.0 0.8 TA =25°C 0.6 4.0 100 0.0 0 4.5 5.0 5.5 6.0 SUPPLY VOLTAGE (V) 1.4 1.2 1.0 0.8 0.6 −55 6.0 30.0 0.98 1.2 200 400 600 800 1000 CAPACITANCE (pF) 125 25 SUPPLY VOLTAGE (V) 1.02 1.00 1.4 1.6 NORMALIZED SET-UP 1.4 25 1.6 NORMALIZED SET-UP TIME vs. TEMPERATURE 1.2 1.6 0.6 −55 CLOCK TO OUTPUT TIME vs. VCC NORMALIZED SET-UP TIME vs. SUPPLY VOLTAGE NORMALIZED SET -UP TIME NORMALIZED CLOCK-TO-OUTPUT TIME CLOCK TO OUTPUT TIME vs. TEMPERATURE NORMALIZED SUPPLY CURRENT vs. CLOCK PERIOD NORMALIZED ICC 125 AMBIENT TEMPERATURE (°C) SUPPLY VOLTAGE (V) 0.88 25 AMBIENT TEMPERATURE (°C) OUTPUT SINK CURRENT (mA) NORMALIZED ICC 1.6 NORMALIZED CLOCK-TO-OUTPUT TIME Typical DC and AC Characteristics OUTPUT SINK CURRENT vs. OUTPUT VOLTAGE 175 150 125 100 75 VCC =5.0V TA =25°C 50 25 0 0.0 1.0 2.0 3.0 4.0 OUTPUT VOLTAGE (V) C235A-10 Document #: 38-04002 Rev. *B Page 6 of 10 CY7C235A Ordering Information Speed (ns) tSA tCO Ordering Code 25 12 CY7C235A-25PC 30 15 CY7C235A-30JC 40 20 CY7C235A-40PC CY7C235A-40DMB CY7C235A-40LMB Package Name P13 J64 P13 D14 L64 Package Type 24-Lead (300-Mil) Molded DIP 28-Lead Plastic Leaded Chip Carrier 24-Lead (300-Mil) Molded DIP 24-Lead (300-Mil) CerDIP 28-Square Leadless Chip Carrier Operating Range Commercial Military MILITARY SPECIFICATIONS Group A Subgroup Testing DC Characteristics Parameter VOH VOL VIH VIL IIX IOZ ICC Subgroups 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 1, 2, 3 Switching Characteristics Parameter tSA tHA tCO Subgroups 7, 8, 9, 10, 11 7, 8, 9, 10, 11 7, 8, 9, 10, 11 Package Diagrams 24-Lead (300-Mil) CerDIP D14 MIL-STD-1835 D- 9 Config.A 51-80031-** Document #: 38-04002 Rev. *B Page 7 of 10 CY7C235A Package Diagrams (continued) 28-Lead Plastic Leaded Chip Carrier J64 51-85001-*A 28-Square Leadless Chip Carrier L64 MIL-STD-1835 C-4 51-80051-** Document #: 38-04002 Rev. *B Page 8 of 10 CY7C235A Package Diagrams (continued) 24-Lead (300-Mil) Molded DIP P13 51-85013-A All product and company names mentioned in this document may be the trademarks of their respective holders. Document #: 38-04002 Rev. *B Page 9 of 10 © Cypress Semiconductor Corporation, 2002. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use of any circuitry other than circuitry embodied in a Cypress Semiconductor product. Nor does it convey or imply any license under patent or other rights. Cypress Semiconductor does not authorize its products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress Semiconductor products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress Semiconductor against all charges. CY7C235A Document History Page Document Title: CY7C235A 1K x 8 Registered PROM Document Number: 38-04002 REV. ECN NO. Issue Date Orig. of Change Description of Change ** 113857 03/06/02 DSG Change from Spec number: 38-00229 to 38-04002 *A 118893 10/09/02 GBI Update ordering information *B 122243 12/27/02 RBI Add power up requirements to maximum ratings information. Document #: 38-04002 Rev. *B Page 10 of 10