LTR REVISION DATE B 12-06-05 CHIP MATERIAL LENS COLOR EMISSION COLOR InGaN WATER CLEAR INCAND. WHITE Notes: ATTENTION 1. ALL DIMS ARE IN MILLIMETERS (INCHES). 2. TOLERANCE IS ±0.25mm (±.010") UNLESS OTHERWISE SPECIFIED. 3. PROTRUDED RESIN UNDER FLANGE IS 1.0mm (.04") MAX. 4. LEAD SPACING IS MEASURED WHERE LEADS EMERGE FROM THE PACKAGE. 5. LEADS TO BE SOLDERABLE AND CAPABLE OF MEETING THE SOLDERABILITY REQUIREMENTS OF MIL-STD-202, METHOD 208. 6. MANUFACTURE DATE SHALL NOT BE OLDER THAN 26 WEEKS (6 MONTHS). -PROPRIETARY- R This document contains Proprietary information of LEDTRONICS, INC. It may not be copied, used or disclosed for any purpose without the prior express written consent of LEDTRONICS, INC. OBSERVE PRECAUTIONS FOR HANDLING- ELECTROSTATIC SENSITIVE DEVICES TITLE L200-0IW-20D TM TM TM 23105 KASHIWA COURT TORRANCE, CA 90505 .XXX ± .010 .XX ± .025 ANGLES ± 0°,30' FRACT. ± 1/32 TOLERANCE PER ANSI-Y14.5 (UNLESS OTHERWISE STATED) 2:1 DSDC307 CODE IDENT NO. 8Z410 SHEET SCALE DWG NO DWG BY RM CHK BY 1 OF 3 QA MNFG DATE 03-26-03 CUSTOMER APPD RM LTR REVISION DATE B 12-06-05 Absolute Maximum Ratings at Ta 25 25°C Parameter MAX. Unit Power Dissipation 80 mW Peak Forward Current (1/10 Duty Cycle, 0.1ms Pulse Wi dth) 100 mA Continuous Forward Current 20 mA Derating Linear From 50 50°C C 0.4 mA/°C mA/ C 5 V Reverse Voltage Operating Temperature Range 150 -20°C -20 C to +80°C +80 C Storage Temperature Range -30°C -30 C to +100°C +100 C Electrostatic Discharge (ESD) Lead Soldering Temp erature [4mm (.157 ) From Body] El ectrical Optical Characteristics at Param eter ter Ta=25 =25°C Min. Typ. Max. Unit Test st Condition Iv 4900 6000 --- m cd If =20mA (Note 1) --- 22 --- Deg (Note 2) 2 1/2 Forward Voltage Vf --- 3.5 4.0 V If=20mA Reverse Current IR --- --- 100 uA VR=5V SCP --- --- --- --- --- --- Lumens --- --- --- --- --- --- Radiant Intensity --- --- --- --- uW/sr --- Color Rank Bin Limi ts (CIE1931 x, y coordinates) Lower Right Upper Right x x y y 0.435 0.375 0.460 0.436 Lower Left x y 0.405 0.365 LTWW Notes: 260°C 260 C for 5 Seconds Symbol Luminous Intensity Viewing Angle V Upper Left x y 0.425 0.427 1 Luminous intensity is measured with a light sensor and filter combination that approximates the CIE eye-response curve. 2. 1/2 is the off-axis at which the luminous inensity is half tha axial luminous intensity. -PROPRIETARYThis document contains Proprietary information of LEDTRONICS, INC. It may not be copied, used or disclosed for any purpose without the prior express written consent of LEDTRONICS, INC. R TM TM .XXX ± .010 23105 KASHIWA COURT TORRANCE, CA 90505 TITLE L200-0IW-20D TM .XX ± .025 ANGLES ± 0°,30' 0 ,30' FRACT. ± 1/32 TOLERANCE PER ANSI-Y14.5 (UNLESS OTHERWISE STATED) DWG NO SCALE DSDC307-A CODE IDENT NO. 8Z410 DWG BY RM SHEET NTS CHK BY 2 QA OF 3 MNFG DATE 12-06-05 CUSTOMER APPD RM LTR REVISION DATE B APPD 12-06-05 RM Typical Electrical / Optical Characteristics Curves (25°C Ambient Temperature Unless Otherwise Noted) CIE 1931 Chromaticity Diagram Spectral Radiance 0.45 10 BIN 1 BIN 2 BIN 3 BIN 4 0.43 Normalized Response 0.8 0.41 Y 0.39 0.6 0.4 0.37 0.2 0.35 0.0 0.35 0.37 0.39 0.41 0.43 0.45 0.47 420 380 0.49 460 500 540 580 620 660 700 740 780 Wavelength (nm) X Relative Luminous Intensity vs Forward Current Forward Current vs Forward Voltage Relative Intensity (LOP@20mA=1) Forward Current If (mA) 3 30 25 20 15 10 5 2.5 2 1.5 1 0. 5 0 2.5 2.7 2.9 3.1 3.3 3.7 3.5 0 3.9 5 0 Forward Voltage Vf (V) 10 15 20 25 30 35 Forward Current If (mA) Forward Current vs Derating Curve Beam Pattern 0°C 60 -30°C 30°C 60°C -60°C Forward Current If (mA) 50 40 30 20 10 -90°C 1.0 08 0.6 0.4 0.2 0.2 0.4 0.6 0.8 90°C 1. 0 0 0 10 Relative Intensity (LO P@M AX=1) -PROPRIETARYThis document contains Proprietary TM LEDTRONICS, INC. information of It may not be copied, used or disclosed for any purpose without the prior express TM LEDTRONICS, INC. written consent of R 20 30 40 50 60 70 80 90 Derating Curve Ta (°C) TITLE L200-0IW-20D DWG NO SCALE SHEET DATE TM .XXX ± .010 23105 KASHIWA COURT TORRANCE, CA 90505 .XX ± .025 ANGLES ± 0°,30' FRACT. ± 1/32 TOLERANCE PER ANSI-Y14.5 (UNLESS OTHERWISE STATED) DSDC307-B CODE IDENT NO. 8Z410 DWG BY RM NTS CHK BY 3 QA OF 3 MNFG 12-06-05 CUSTOMER