White Electronic Designs W3DG647V-D1 64MB- 8Mx64 SDRAM UNBUFFERED FEATURES DESCRIPTION PC100 and PC133 compatible Burst Mode Operation Auto and Self Refresh capability LVTTL compatible inputs and outputs Serial Presence Detect with EEPROM The W3DG647V is a 8Mx64 synchronous DRAM module which consists of eight 8Mx8 SDRAM components in TSOP II package, and one 2Kb EEPROM in an 8 pin TSSOP package for Serial Presence Detect which are mounted on a 144 pin SO-DIMM multilayer FR4 Substrate. Fully synchronous: All signals are registered on the positive edge of the system clock Programmable Burst Lengths: 1, 2, 4, 8 or Full Page 3.3V ± 0.3V Power Supply 144 Pin SO-DIMM JEDEC * This product is subject to change without notice. PIN NAMES PIN CONFIGURATIONS (FRONT SIDE/BACK SIDE) Pin 1 3 5 7 9 11 13 15 17 19 21 23 25 27 29 31 33 35 37 39 41 43 45 47 49 Front VSS DQ0 DQ1 DQ2 DQ3 VCC DQ4 DQ5 DQ6 DQ7 VSS DQM0 DQM1 VCC A0 A1 A2 VSS DQ8 DQ9 DQ10 DQ11 VCC DQ12 DQ13 Pin 2 4 6 8 10 12 14 16 18 20 22 24 26 28 30 32 34 36 38 40 42 44 46 48 50 Back VSS DQ32 DQ33 DQ34 DQ35 VCC DQ36 DQ37 DQ38 DQ39 VSS DQM4 DQM5 VCC A3 A4 A5 VSS DQ40 DQ41 DQ42 DQ43 VCC DQ44 DQ45 Pin 51 53 55 57 59 Front DQ14 DQ15 VSS NC NC Pin 52 54 56 58 60 Back DQ46 DQ47 VSS NC NC VOLTAGE KEY 61 63 65 67 69 71 73 75 77 79 81 83 85 87 89 91 93 CLK0 VCC RAS# WE# CS0# NC DNU VSS NC NC VCC DQ16 DQ17 DQ18 DQ19 VSS DQ20 62 64 66 68 70 72 74 76 78 80 82 84 86 88 90 92 94 CKE0 VCC CAS# NC NC NC CK1 VSS NC NC VCC DQ48 DQ49 DQ50 DQ51 VSS DQ52 Pin 95 97 99 101 103 105 107 109 111 113 115 117 119 121 123 125 127 129 131 133 135 137 139 141 143 Front DQ21 DQ22 DQ23 VCC A6 A8 VSS A9 A10/AP VCC DQM2 DQM3 VSS DQ24 DQ25 DQ26 DQ27 VCC DQ28 DQ29 DQ30 DQ31 VSS **SDA VCC Pin 96 98 100 102 104 106 108 110 112 114 116 118 120 122 124 126 128 130 132 134 136 138 140 142 144 Back DQ53 DQ54 DQ55 VCC A7 BA0 VSS BA1 A11 VCC DQM6 DQM7 VSS DQ56 DQ57 DQ58 DQ59 VCC DQ60 DQ61 DQ62 DQ63 VSS **SCL VCC A0 – A11 Address input (Multiplexed) BA0-1 Select Bank DQ0-63 Data Input/Output CLK0,CK1 Clock input CKE0 Clock Enable input CS0# Chip select Input RAS# Row Address Strobe CAS# Column Address Strobe WE# Write Enable DQM0-7 DQM VCC Power Supply (3.3V) VSS Ground SDA Serial data I/O SCL Serial clock DNU Do not use NC No Connect **These pins should be NC in the system which does not support SPD. White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2003 Rev. 1 1 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG647V-D1 FUNCTIONAL BLOCK DIAGRAM WE# S0# RAS#,CAS# CLK1 CLK0 CKEO BAO,BA1,A0- A11 DQ0-7 DQ0-7 DQ0-7 DQ32-39 LDQM DQM0 LDQM DQM4 U1 SCL U5 SERIAL PD EEPROM SDA U3 DQ0-7 DQ8-15 DQ0-7 DQ40-47 LDQM DQN1 LDQM DQM1 U2 U4 DQ0-7 DQ16-23 DQ0-7 DQ48-55 LDQM DQM2 LDQM DQM6 U5 U7 DQ0-7 DQ24-31 DQ0-7 DQ56-63 LDQM DQM3 LDQM DQM7 U6 U8 White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2003 Rev. 1 2 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG647V-D1 ABSOLUTE MAXIMUM RATINGS Parameter Symbol Value Units Voltage on any pin relative to VSS VIN, VOUT -1.0 ~ 4.6 V Voltage on VCC supply relative to VSS VCC, VCCQ -1.0 ~ 4.6 V TSTG -55 ~ +150 °C Power Dissipation Storage Temperature PD 8 W Short Circuit Current IOS 50 mA Note: Permanent device damage may occur if "ABSOLUTE MAXIMUM RATINGS" are exceeded. Functional operation should be restricted to recommended operating condition. Exposure to higher than recommended voltage for extended periods of time could affect device reliability. RECOMMENDED DC OPERATING CONDITIONS (Voltage Referenced to: VSS = 0V, TA = 0°C to +70°C) Parameter Symbol Min Typ Max Unit Supply Voltage VCC 3.0 3.3 3.6 V Input High Voltage VIH 2.0 3.0 VCCQ+0.3 V Note 1 Input Low Voltage VIL -0.3 — 0.8 V 2 Output High Voltage VOH 2.4 — — V IOH= -2mA Output Low Voltage VOL — — 0.4 V IOL= -2mA ILI -10 — 10 µA 3 Input Leakage Current Note: 1. VIH (max)= 5.6V AC. The overshoot voltage duration is ≤ 3ns. 2. VIL (min)= -2.0V AC. The undershoot voltage duration is ≤ 3ns. 3. Any input 0V ≤ VIN ≤ VCCQ Input leakage currents include Hi-Z output leakage for all bi-directional buffers with Tri-State outputs. CAPACITANCE (TA = 23°C, f = 1MHz, VCC = 3.3V, VREF=1.4V ± 200mV) Parameter Symbol Min Max Unit Input Capacitance (A0-A12) CIN1 - 45 pF Input Capacitance (RAS#,CAS#,WE#) CIN2 - 45 pF Input Capacitance (CKE0) CIN3 - 25 pF Input Capacitance (CLK0,CK1) CIN4 - 21 pF Input Capacitance (CS0#) CIN5 - 25 pF Input Capacitance (DQM0-DQM7) CIN6 - 12 pF Input Capacitance (BA0-BA1) CIN7 - 45 pF Data input/output capacitance (DQ0-DQ63) COUT - 12 pF White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2003 Rev. 1 3 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs W3DG647V-D1 OPERATING CURRENT CHARACTERISTICS (VCC = 3.3V, TA = 0°C to +70°C) Version Parameter Symbol Conditions 133 100 Units Note 460 400 mA 1 Operating Current (One bank active) ICC1 Burst Length = 1 tRC ³ tRC(min) IOL = 0mA Precharge Standby Current in Power Down Mode ICC2P CKE ≤ VIL(max), tCC = 10ns 5 ICC2PS CKE & CLK ≤ VIL(max), tCC = ∞ 5 Precharge Standby Current in Non-Power Down Mode Icc2N CKE ≥ VIH(min), CS ≥ VIH(min), tcc =10ns Input signals are charged one time during 20 60 Icc2NS CKE ≥ VIH(min), CLK ≤VIL(max), tCC = ∞ Input signals are stable 25 Active standby current in power-down mode ICC3P CKE ≥ VIL(max), tCC = 10ns 15 ICC3PS CKE & CLK ≤ VIL(max), tCC = ∞ 15 Active standby current in non power-down mode ICC3N CKE ≥ VIH(min), CS ≥ VIH(min), tcc = 10ns Input signals are changed one time during 20ns 120 mA ICC3NS CKE ≥ VIH(min), CLK ≤ VIL(max), tcc = ∞ Input signals are stable 100 mA ICC4 Io = mA Page burst 4 Banks activated tCCD = 2CLK 460 540 Operating current (Burst mode) Refresh current ICC5 tRC ≥ tRC(min) Self refresh current ICC6 CKE ≤ 0.2V mA mA 5 mA 380 mA 1 500 mA 2 mA Notes: 1. Measured with outputs open. 2. Refresh period is 64ms. 3. Unless otherwise noticed, input swing level is CMOS (VIH/VIL = VCCQ/VssQ) White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2003 Rev. 1 4 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com White Electronic Designs Part Number Speed W3DG647V-D1 CAS Latency W3DG647V10D1 100MHz CL=2 W3DG647V7D1 133MHz CL=2 W3DG647V75D1 133MHz CL=3 Note: For industrial temperature range product, add an "I" to the end of the part number. PACKAGE DIMENSIONS ALL DIMENSIONS ARE IN INCHES White Electronic Designs Corp. reserves the right to change products or specifications without notice. June 2003 Rev. 1 5 White Electronic Designs Corporation • (602) 437-1520 • www.wedc.com