AD AD7664

a
FEATURES
Throughput: 250 kSPS
INL: 3 LSB Max (0.0046% of Full Scale)
16-Bit Resolution with No Missing Codes
S/(N+D): 90 dB Typ @ 100 kHz
THD: –100 dB Typ @ 100 kHz
Analog Input Voltage Ranges
Bipolar: 10 V, 5 V, 2.5 V
Unipolar: 0 V to 10 V, 0 V to 5 V, 0 V to 2.5 V
Both AC and DC Specifications
No Pipeline Delay
Parallel (8/16 Bits) and Serial 5 V/3 V Interface
SPI®/QSPI™/MICROWIRE™/DSP Compatible
Single 5 V Supply Operation
Power Dissipation
35 mW Typical
15 W @ 100 SPS
Power-Down Mode: 7 W Max
Package: 48-Lead Quad Flatpack (LQFP)
Package: 48-Lead Chip Scale (LFCSP)
Pin-to-Pin Compatible with the AD7660/AD7664/AD7665
APPLICATIONS
Data Acquisition
Motor Control
Communication
Instrumentation
Spectrum Analysis
Medical Instruments
Process Control
16-Bit, 250 kSPS CMOS ADC
AD7663
FUNCTIONAL BLOCK DIAGRAM
AVDD AGND REF REFGND
IND(4R)
INC(4R)
INB(2R)
INA(R)
4R
DVDD
DGND
AD7663
4R
2R
OVDD
SERIAL
PORT
R
SWITCHED
CAP DAC
INGND
SER/PAR
BUSY
PARALLEL 16
INTERFACE
D[15:0]
CS
CLOCK
PD
RESET
OGND
RD
CONTROL LOGIC AND
CALIBRATION CIRCUITRY
OB/2C
BYTESWAP
CNVST
PulSAR Selection
Type/kSPS
100–250
500–570
Pseudo
Differential
AD7660
AD7650
AD7664
True Bipolar
AD7663
AD7665
AD7671
True Differential
AD7675
AD7676
AD7677
18-Bit
AD7678
AD7679
AD7674
AD7654
AD7655
Simultaneous/
Multichannel
800–1000
GENERAL DESCRIPTION
The AD7663 is a 16-bit, 250 kSPS, charge redistribution SAR,
analog-to-digital converter that operates from a single 5 V power
supply. It contains a high speed 16-bit sampling ADC, a resistor
input scaler that allows various input ranges, an internal conversion clock, error correction circuits, and both serial and parallel
system interface ports.
The AD7663 is hardware factory-calibrated and is comprehensively tested to ensure such ac parameters as signal-to-noise ratio
(SNR) and total harmonic distortion (THD), in addition to the
more traditional dc parameters of gain, offset, and linearity.
It is fabricated using Analog Devices’ high performance, 0.6 micron
CMOS process and is available in a 48-lead LQFP and a tiny
48-lead LFCSP with operation specified from –40°C to +85°C.
PRODUCT HIGHLIGHTS
1. Fast Throughput
The AD7663 is a 250 kSPS charge redistribution, 16-bit
SAR ADC with various bipolar and unipolar input ranges.
2. Single-Supply Operation
The AD7663 operates from a single 5 V supply and dissipates
only 35 mW typical. Its power dissipation decreases with
the throughput to, for instance, only 15 µW at a 100 SPS
throughput.
It consumes 7 µW maximum when in power-down.
3. Superior INL
The AD7663 has a maximum integral nonlinearity of 3 LSB
with no missing 16-bit code.
4. Serial or Parallel Interface
Versatile parallel (8 bits or 16 bits) or 2-wire serial interface
arrangement compatible with both 3 V or 5 V logic.
REV. B
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties that
may result from its use. No license is granted by implication or otherwise
under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective companies.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
www.analog.com
Fax: 781/326-8703
© 2003 Analog Devices, Inc. All rights reserved.
AD7663–SPECIFICATIONS (–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)
Parameter
Conditions
Min
RESOLUTION
ANALOG INPUT
Voltage Range
Common-Mode Input Voltage
Analog Input CMRR
Input Impedance
VIND – VINGND
VINGND
fIN = 45 kHz
THROUGHPUT SPEED
Complete Cycle
Throughput Rate
DC ACCURACY
Integral Linearity Error
No Missing Codes
Transition Noise
Bipolar Zero Error2, TMIN to TMAX
Bipolar Full-Scale Error2, TMIN to TMAX
Unipolar Zero Error2, TMIN to TMAX
Unipolar Full-Scale Error 2, TMIN to TMAX
Power Supply Sensitivity
AC ACCURACY
Signal-to-Noise
Spurious-Free Dynamic Range
Total Harmonic Distortion
Signal-to-(Noise+Distortion)
±4 REF, 0 V to 4 REF, ±2 REF (See Table I)
–0.1
+0.5
62
See Table I
V
dB
4
250
µs
kSPS
+3
±0.1
LSB1
Bits
LSB
LSB
% of FSR
% of FSR
% of FSR
% of FSR
LSB
90
90
100
–100
90
30
800
dB3
dB
dB
dB
dB
dB
kHz
2
5
ns
ps rms
µs
–3
16
0.7
±5 V Range
Other Range
–25
–0.06
–0.25
–0.18
–0.38
AVDD = 5 V ±5%
fIN = 10 kHz
fIN = 100 kHz
fIN = 100 kHz
fIN = 100 kHz
fIN = 10 kHz
fIN = 100 kHz, –60 dB Input
Full-Scale Step
REFERENCE
External Reference Voltage Range
External Reference Current Drain
250 kSPS Throughput
89
88.5
+25
+0.06
+0.25
+0.18
+0.38
2.75
2.3
DIGITAL INPUTS
Logic Levels
VIL
VIH
IIL
IIH
2.5
50
–0.3
+2.0
–1
–1
DIGITAL OUTPUTS
Data Format
Pipeline Delay
ISINK = 1.6 mA
ISOURCE = –500 µA
Unit
Bits
0
SAMPLING DYNAMICS
Aperture Delay
Aperture Jitter
Transient Response
POWER SUPPLIES
Specified Performance
AVDD
DVDD
OVDD
Operating Current
AVDD
DVDD5
OVDD5
Power Dissipation6
Max
16
–3 dB Input Bandwidth
VOL
VOH
Typ
AVDD – 1.85
V
µA
+0.8
DVDD + 0.3
+1
+1
V
V
µA
µA
Parallel or Serial 16-Bit
Conversion Results Available Immediately
after Completed Conversion
0.4
OVDD – 0.6
V
V
4.75
4.75
2.7
V
V
V
5
5
5.25
5.25
5.254
250 kSPS Throughput
250 kSPS Throughput5
100 SPS Throughput5
In Power-Down Mode7
–2–
5
1.8
10
35
15
41
7
mA
mA
µA
mW
µW
µW
REV. B
AD7663
Parameter
Conditions
Min
TEMPERATURE RANGE 8
Specified Performance
TMIN to TMAX
–40
Typ
Max
Unit
+85
°C
NOTES
1
LSB means least significant bit. With the ±5 V input range, one LSB is 152.588 µV.
2
See Definition of Specifications section. These specifications do not include the error contribution from the external reference.
3
All specifications in dB are referred to a full-scale input FS. Tested with an input signal at 0.5 dB below full scale, unless otherwise specified.
4
The max should be the minimum of 5.25 V and DVDD + 0.3 V.
5
Tested in Parallel Reading Mode.
6
Tested with the 0 V to 5 V range and V IN – VINGND = 0 V. See Power Dissipation section.
7
With OVDD below DVDD + 0.3 V and all digital inputs forced to DVDD or DGND, respectively.
8
Contact factory for extended temperature range.
Specifications subject to change without notice.
Table I. Analog Input Configuration
Input Voltage
Range
IND(4R)
INC(4R)
INB(2R)
INA(R)
Input
Impedance1
±4 REF2
±2 REF
±REF
0 V to 4 REF
0 V to 2 REF
0 V to REF
VIN
VIN
VIN
VIN
VIN
VIN
INGND
VIN
VIN
VIN
VIN
VIN
INGND
INGND
VIN
INGND
VIN
VIN
REF
REF
REF
INGND
INGND
VIN
5.85 kW
3.41 kW
2.56 kW
3.41 kW
2.56 kW
Note 3
NOTES
1
Typical analog input impedance.
2
With REF = 3 V, in this range, the input should be limited to –11 V to +12 V.
3
For this range the input is high impedance.
TIMING SPECIFICATIONS
(–40C to +85C, AVDD = DVDD = 5 V, OVDD = 2.7 V to 5.25 V, unless otherwise noted.)
Parameter
Refer to Figures 11 and 12
Convert Pulsewidth
Time between Conversions
CNVST LOW to BUSY HIGH Delay
BUSY HIGH All Modes Except in
Master Serial Read after Convert Mode
Aperture Delay
End of Conversion to BUSY LOW Delay
Conversion Time
Acquisition Time
RESET Pulsewidth
Symbol
Min
t1
t2
t3
t4
5
4
t5
t6
t7
t8
t9
Refer to Figures 13, 14, 15, and 16 (Parallel Interface Modes)
CNVST LOW to DATA Valid Delay
DATA Valid to BUSY LOW Delay
Bus Access Request to DATA Valid
Bus Relinquish Time
t10
t11
t12
t13
Refer to Figures 17 and 18 (Master Serial Interface Modes)1
CS LOW to SYNC Valid Delay
CS LOW to Internal SCLK Valid Delay
CS LOW to SDOUT Delay
CNVST LOW to SYNC Delay (Read during Convert)
SYNC Asserted to SCLK First Edge Delay2
Internal SCLK Period2
Internal SCLK HIGH2
Internal SCLK LOW2
SDOUT Valid Setup Time2
SDOUT Valid Hold Time2
SCLK Last Edge to SYNC Delay2
t14
t15
t16
t17
t18
t19
t20
t21
t22
t23
t24
REV. B
–3–
Typ
Max
Unit
30
1.25
ns
µs
ns
µs
2
10
1.25
2.75
10
1.25
20
40
15
5
10
10
10
0.5
4
25
15
9.5
4.5
2
3
40
ns
ns
µs
µs
ns
µs
ns
ns
ns
ns
ns
ns
µs
ns
ns
ns
ns
ns
ns
ns
AD7663
TIMING SPECIFICATIONS (continued)
Symbol
Parameter
Min
Typ
Max
Unit
10
10
10
1
Refer to Figures 17 and 18 (Master Serial Interface Modes)
CS HIGH to SYNC HI-Z
CS HIGH to Internal SCLK HI-Z
CS HIGH to SDOUT HI-Z
BUSY HIGH in Master Serial Read after Convert
CNVST LOW to SYNC Asserted Delay
(Master Serial Read after Convert)
SYNC Deasserted to BUSY LOW Delay
Refer to Figures 19 and 21 (Slave Serial Interface Modes)
External SCLK Setup Time
External SCLK Active Edge to SDOUT Delay
SDIN Setup Time
SDIN Hold Time
External SCLK Period
External SCLK HIGH
External SCLK LOW
t25
t26
t27
t28
t29
See Table II
1.25
ns
ns
ns
µs
µs
t30
25
ns
t31
t32
t33
t34
t35
t36
t37
5
3
5
5
25
10
10
ns
ns
ns
ns
ns
ns
ns
16
NOTES
1
In serial interface modes, the SYNC, SCLK, and SDOUT timings are defined with a maximum load C L of 10 pF; otherwise, the load is 60 pF maximum.
2
In Serial Master Read during Convert Mode. See Table II for Master Read after Convert Mode.
Specifications subject to change without notice.
Table II. Serial Clock Timings in Master Read after Convert
DIVSCLK[1]
DIVSCLK[0]
SYNC to SCLK First Edge Delay Minimum
Internal SCLK Period Minimum
Internal SCLK Period Maximum
Internal SCLK HIGH Minimum
Internal SCLK LOW Minimum
SDOUT Valid Setup Time Minimum
SDOUT Valid Hold Time Minimum
SCLK Last Edge to SYNC Delay Minimum
BUSY HIGH Width Maximum
1.6mA
TO OUTPUT
PIN
t18
t19
t19
t20
t21
t22
t23
t24
t28
0
0
0
1
1
0
1
1
Unit
4
25
40
15
9.5
4.5
2
3
2
20
50
70
25
24
22
4
60
2.5
20
100
140
50
49
22
30
140
3.5
20
200
280
100
99
22
90
300
5.75
ns
ns
ns
ns
ns
ns
ns
ns
µs
IOL
1.4V
CL
60pF*
500A
2V
IOH
0.8V
tDELAY
*IN SERIAL INTERFACE MODES, THE SYNC, SCLK, AND
SDOUT TIMINGS ARE DEFINED WITH A MAXIMUM LOAD
CL OF 10pF; OTHERWISE, THE LOAD IS 60pF MAXIMUM.
tDELAY
2V
0.8V
Figure 1. Load Circuit for Digital Interface Timing
2V
0.8V
Figure 2. Voltage Reference Levels for Timing
–4–
REV. B
AD7663
ABSOLUTE MAXIMUM RATINGS 1
REFGND
REF
INGND
NC
NC
NC
NC
NC
IND(4R)
INC(4R)
INB(2R)
INA(R)
PIN CONFIGURATION
ST-48 and CP-48
Analog Inputs
IND2, INC2, INB2 . . . . . . . . . . . . . . . . . . . . –11 V to +30 V
INA, REF, INGND, REFGND
. . . . . . . . . . . . . . . . . . . . AGND – 0.3 V to AVDD + 0.3 V
Ground Voltage Differences
AGND, DGND, OGND . . . . . . . . . . . . . . . . . . . . . ±0.3 V
Supply Voltages
AVDD, DVDD, OVDD . . . . . . . . . . . . . . . . –0.3 V to +7 V
AVDD to DVDD, AVDD to OVDD . . . . . . . . . . . . . . ±7 V
DVDD to OVDD . . . . . . . . . . . . . . . . . . . . . –0.3 V to +7 V
Digital Inputs . . . . . . . . . . . . . . . . –0.3 V to DVDD + 0.3 V
Internal Power Dissipation3 . . . . . . . . . . . . . . . . . . . 700 mW
Internal Power Dissipation4 . . . . . . . . . . . . . . . . . . . . . 2.5 W
Junction Temperature . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature Range
(Soldering 10 sec) . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
48 47 46 45 44 43 42 41 40 39 38 37
AGND 1
AVDD 2
NC 3
BYTESWAP 4
OB/2C 5
NC 6
RESET
CS
RD
DGND
29 BUSY
28
27
26
25
D15
D14
D13
D12
D11/RDERROR
D9/SCLK
D10/SYNC
DVDD
DGND
D8/SDOUT
OVDD
D7/RDC/SDIN
OGND
13 14 15 16 17 18 19 20 21 22 23 24
D4/EXT/INT
D5/INVSYNC
D6/INVSCLK
NC = NO CONNECT
Stresses above those listed under Absolute Maximum Ratings may cause permanent damage to the device. This is a stress rating only; functional operation of the
device at these or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute maximum rating
conditions for extended periods may affect device reliability.
2
See Analog Inputs section.
3
Specification is for device in free air: 48-Lead LQFP: qJA = 91°C/W, qJC = 30°C/W.
4
Specification is for device in free air: 48-Lead LFCSP: qJC = 26⬚C/W.
PD
33
30
D2/DIVSCLK[0] 11
D3/DIVSCLK[1] 12
1
34
31
TOP VIEW
(Not to Scale)
SER/PAR 8
D0 9
D1 10
AGND
CNVST
32
AD7663
NC 7
35
36
PIN 1
IDENTIFIER
ORDERING GUIDE
Model
Temperature Range
Package Description
Package Option
AD7663AST
AD7663ASTRL
AD7663ACP
AD7663ACPRL
EVAL-AD7663CB1
EVAL-CONTROL BRD22
–40°C to +85°C
–40°C to +85°C
–40⬚C to +85⬚C
–40⬚C to +85⬚C
Quad Flatpack (LQFP)
Quad Flatpack (LQFP)
Chip Scale (LFCSP)
Chip Scale (LFCSP)
Evaluation Board
Controller Board
ST-48
ST-48
CP-48
CP-48
NOTES
1
This board can be used as a standalone evaluation board or in conjunction with the EVAL-CONTROL BRD2 for evaluation/demonstration purposes.
2
This board allows a PC to control and communicate with all Analog Devices evaluation boards ending in the CB designators.
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the AD7663 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
REV. B
–5–
AD7663
PIN FUNCTION DESCRIPTION
Pin
No.
Mnemonic
Type Description
1
2
3, 6, 7,
44–48
4
AGND
AVDD
NC
P
P
Analog Power Ground Pin.
Input Analog Power Pin. Nominally 5 V.
No Connect.
BYTESWAP
DI
5
OB/2C
DI
8
SER/PAR
DI
9, 10
D[0:1]
DO
11, 12
D[2:3] or
DI/O
Parallel Mode Selection (8/16 Bit). When LOW, the LSB is output on D[7:0] and the MSB is output
on D[15:8]. When HIGH, the LSB is output on D[15:8] and the MSB is output on D[7:0].
Straight Binary/Binary Twos Complement. When OB/2C is HIGH, the digital output is straight
binary; when LOW, the MSB is inverted, resulting in a twos complement output from its internal
shift register.
Serial/Parallel Selection Input. When LOW, the Parallel Port is selected; when HIGH, the
Serial Interface Mode is selected and some bits of the Data bus are used as a Serial Port.
Bit 0 and Bit 1 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs
are in high impedance.
When SER/PAR is LOW, these outputs are used as Bit 2 and Bit 3 of the Parallel Port Data
Output Bus.
When SER/PAR is HIGH, EXT/INT is LOW and RDC/SDIN is LOW, which is the Serial
Master Read after Convert Mode. These inputs, part of the Serial Port, are used to slow down,
if desired, the internal serial clock that clocks the data output. In the other serial modes, these
pins are high impedance outputs.
When SER/PAR is LOW, this output is used as Bit 4 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the Serial Port, is used as a digital select input for
choosing the internal or an external data clock, called respectively, Master and Slave Modes.
With EXT/INT tied LOW, the internal clock is selected on SCLK output. With EXT/INT
set to a logic HIGH, output data is synchronized to an external clock signal connected to the
SCLK input, and external clock is gated by CS.
When SER/PAR is LOW, this output is used as Bit 5 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the Serial Port, is used to select the active state of
the SYNC signal. When LOW, SYNC is active HIGH. When HIGH, SYNC is active LOW.
When SER/PAR is LOW, this output is used as Bit 6 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the Serial Port, is used to invert the SCLK signal.
It is active in both master and slave mode.
When SER/PAR is LOW, this output is used as Bit 7 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this input, part of the Serial Port, is used as either an external data
input or a read mode selection input, depending on the state of EXT/INT.
When EXT/INT is HIGH, RDC/SDIN could be used as a data input to daisy-chain the conversion
results from two or more ADCs onto a single SDOUT line. The digital data level on SDIN is
output on DATA with a delay of 16 SCLK periods after the initiation of the read sequence.
When EXT/INT is LOW, RDC/SDIN is used to select the read mode. When RDC/SDIN is
HIGH, the previous data is output on SDOUT during conversion. When RDC/SDIN is LOW,
the data can be output on SDOUT only when the conversion is complete.
Input/Output Interface Digital Power Ground.
Input/Output Interface Digital Power. Nominally at the same supply as the supply of the host
interface (5 V or 3 V).
Digital Power. Nominally at 5 V.
Digital Power Ground.
DIVSCLK[0:1]
13
D[4]
or EXT/INT
DI/O
14
D[5]
or INVSYNC
DI/O
15
D[6]
or INVSCLK
DI/O
16
D[7]
or RDC/SDIN
DI/O
17
18
OGND
OVDD
P
P
19
20
DVDD
DGND
P
P
–6–
REV. B
AD7663
PIN FUNCTION DESCRIPTION (continued)
Pin
No.
Mnemonic
Type Description
21
D[8]
or SDOUT
DO
22
D[9]
or SCLK
23
D[10]
or SYNC
24
D[11]
or RDERROR
25–28
D[12:15]
29
BUSY
30
31
32
DGND
RD
CS
33
RESET
34
PD
35
CNVST
36
37
38
39
40, 41,
42, 43
AGND
REF
REFGND
INGND
INA, INB,
INC, IND
When SER/PAR is LOW, this output is used as Bit 8 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this output, part of the Serial Port, is used as a serial data output
synchronized to SCLK. Conversion results are stored in an on-chip register. The AD7663 provides
the conversion result, MSB first, from its internal shift register. The Data format is determined
by the logic level of OB/2C. In Serial Mode, when EXT/INT is LOW, SDOUT is valid on both
edges of SCLK.
In serial mode, when EXT/INT is HIGH:
If INVSCLK is LOW, SDOUT is updated on the SCLK rising edge and valid on the next falling edge.
If INVSCLK is HIGH, SDOUT is updated on the SCLK falling edge and valid on the next rising edge.
DI/O When SER/PAR is LOW, this output is used as Bit 9 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this pin, part of the Serial Port, is used as a serial data clock input or
output, dependent upon the logic state of the EXT/INT pin. The active edge where the data
SDOUT is updated depends upon the logic state of the INVSCLK pin.
DO
When SER/PAR is LOW, this output is used as Bit 10 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH, this output, part of the Serial Port, is used as a digital output frame
synchronization for use with the internal data clock (EXT/INT = Logic LOW). When a read
sequence is initiated and INVSYNC is LOW, SYNC is driven HIGH and remains HIGH while
SDOUT output is valid. When a read sequence is initiated and INVSYNC is HIGH, SYNC is
driven LOW and remains LOW while SDOUT output is valid.
DO
When SER/PAR is LOW, this output is used as Bit 11 of the Parallel Port Data Output Bus.
When SER/PAR is HIGH and EXT/INT is HIGH, this output, part of the Serial Port, is used as
an incomplete read error flag. In Slave Mode, when a data read is started and not complete when
the following conversion is complete, the current data is lost and RDERROR is pulsed HIGH.
DO
Bit 12 to Bit 15 of the Parallel Port Data Output Bus. When SER/PAR is HIGH, these outputs
are in high impedance.
DO
Busy Output. Transitions HIGH when a conversion is started and remains HIGH until the
conversion is complete and the data is latched into the on-chip shift register. The falling edge
of BUSY could be used as a data-ready clock signal.
P
Must Be Tied to Digital Ground.
DI
Read Data. When CS and RD are both LOW, the Interface Parallel or Serial Output Bus is enabled.
DI
Chip Select. When CS and RD are both LOW, the Interface Parallel or Serial Output Bus is
enabled. CS is also used to gate the external clock.
DI
Reset Input. When set to a logic HIGH, reset the AD7663. Current conversion, if any, is aborted.
If not used, this pin could be tied to DGND.
DI
Power-Down Input. When set to a logic HIGH, power consumption is reduced and conversions
are inhibited after the current one is completed.
DI
Start Conversion. If CNVST is HIGH when the acquisition phase (t8) is complete, the next falling
edge on CNVST puts the internal sample-and-hold into the hold state and initiates a conversion.
This mode is the most appropriate if low sampling jitter is desired. If CNVST is LOW when the
acquisition phase (t8) is complete, the internal sample-and-hold is put into the hold state and a
conversion is immediately started.
P
Must Be Tied to Analog Ground.
AI
Reference Input Voltage .
AI
Reference Input Analog Ground.
AI
Analog Input Ground.
AI
Analog Inputs. Refer to Table I for input range configuration.
NOTES
AI = Analog Input
DI = Digital Input
DI/O = Bidirectional Digital
DO = Digital Output
P = Power
REV. B
–7–
AD7663
DEFINITION OF SPECIFICATIONS
Integral Nonlinearity Error (INL)
Effective Number of Bits (ENOB)
A measurement of the resolution with a sine wave input. It is
related to S/(N+D) by the following formula:
Linearity error refers to the deviation of each individual code
from a line drawn from “negative full scale” through “positive
full scale.” The point used as negative full scale occurs 1/2 LSB
before the first code transition. Positive full scale is defined as a
level 1 1/2 LSB beyond the last code transition. The deviation is
measured from the middle of each code to the true straight line.
(
)
ENOB = S [ N + D ]dB - 1.76) 6.02
and is expressed in bits.
Total Harmonic Distortion (THD)
The ratio of the rms sum of the first five harmonic components to
the rms value of a full-scale input signal, expressed in decibels.
Differential Nonlinearity Error (DNL)
In an ideal ADC, code transitions are 1 LSB apart. Differential
nonlinearity is the maximum deviation from this ideal value. It is
often specified in terms of resolution for which no missing codes
are guaranteed.
Full-Scale Error
Signal-to-Noise Ratio (SNR)
The ratio of the rms value of the actual input signal to the rms
sum of all other spectral components below the Nyquist frequency, excluding harmonics and dc. The value for SNR is
expressed in decibels.
The last transition (from 011 . . . 10 to 011 . . . 11 in twos
complement coding) should occur for an analog voltage 1 1/2 LSB
below the nominal full scale (2.499886 V for the ±2.5 V range).
The full-scale error is the deviation of the actual level of the last
transition from the ideal level.
Signal-to-(Noise + Distortion) Ratio (S/[N+D])
Bipolar Zero Error
Aperture Delay
The ratio of the rms value of the actual input signal to the
rms sum of all other spectral components below the Nyquist
frequency, including harmonics but excluding dc. The value for
S/(N+D) is expressed in decibels.
The difference between the ideal midscale input voltage (0 V) and
the actual voltage producing the midscale output code.
Unipolar Zero Error
In Unipolar Mode, the first transition should occur at a level
1/2 LSB above analog ground. The unipolar zero error is the
deviation of the actual transition from that point.
A measure of the acquisition performance measured from the
falling edge of the CNVST input to when the input signal is
held for a conversion.
Transient Response
The time required for the AD7663 to achieve its rated accuracy
after a full-scale step function is applied to its input.
Spurious-Free Dynamic Range (SFDR)
The difference, in decibels (dB), between the rms amplitude of
the input signal and the peak spurious signal.
–8–
REV. B
Typical Performance Characteristics– AD7663
8000
3.0
2.5
6802 6745
7000
2.0
1.5
6000
5000
0.5
COUNTS
INL – LSB
1.0
0
–0.5
4000
3000
–1.0
–1.5
1800
2000
–2.0
1000
1000
–2.5
0
–3.0
0
16384
32768
49152
0
33
4
CODE IN HEXA
TPC 4. Histogram of 16,384 Conversions of a DC Input
at the Code Transition
50
9000
45
8000
40
7000
8032
35
6000
30
COUNTS
NUMBER OF UNITS
TPC 1. Integral Nonlinearity vs. Code
25
5000
3944
4000
3902
20
3000
15
2000
10
5
1000
0
0
0
0
0.3
0.6
0.9
1.2
1.5
1.8 2.1
POSITIVE INL – LSB
2.1
2.7
2
233
271
0
0
0
TPC 5. Histogram of 16,384 Conversions of a DC Input
at the Code Center
–0
70
–20
AMPLITUDE – dB OF FULL SCALE
80
60
50
40
30
20
10
0
–3
0
7FFC 7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8005 8006
CODE IN HEXA
TPC 2. Typical Positive INL Distribution (446 Units)
NUMBER OF UNITS
0
7FFD 7FFE 7FFF 8000 8001 8002 8003 8004 8004 8005
CODE
4096 POINT FFT
FS = 250kHz
fIN = 45kHz, –0.5dB
SNR = 90.1dB
SINAD = 89.8dB
THD = –100.5dB
SFDR = 102.7dB
–40
–60
–80
–100
–120
–140
–160
–180
–2.7
–2.4
–2.1
–1.8 –1.5
–1.2
–0.9
0
–0.6 –0.3
NEGATIVE INL – LSB
TPC 3. Typical Negative INL Distribution (446 Units)
REV. B
0
0
65536
25
50
75
FREQUENCY – kHz
TPC 6. FFT Plot
–9–
100
125
AD7663
16.0
–60
110
–65
95
15.5
105
SFDR
–70
100
THD, HARMONICS – dB
15.0
90
SINAD
14.5
85
ENOB – Bits
SNR AND S/[N+D] – dB
SNR
14.0
80
–75
95
–80
90
–85
85
–90
80
–95
SECOND HARMONIC
THD
75
–100
ENOB
70
–105
13.5
75
65
–110
13.0
1000
70
1
10
100
FREQUENCY – kHz
1
60
1000
10
100
FREQUENCY – kHz
TPC 10. THD, Harmonics, and SFDR vs. Frequency
–60
92
–70
–80
THD, HARMONICS – dB
SNR – (REFERRED TO FULL SCALE) – dB
THIRD HARMONIC
–115
TPC 7. SNR, S/(N+D), and ENOB vs. Frequency
SFDR – dB
100
90
88
–90
–100
THD
–110
–120
–130
THIRD HARMONIC
SECOND HARMONIC
–140
–150
86
–80
–70
–60
–50
–40
–30
INPUT LEVEL – dB
–20
–10
–160
–60
0
TPC 8. SNR vs. Input Level
–50
–40
–30
–20
INPUT LEVEL – dB
–10
0
TPC 11. THD, Harmonics vs. Input Level
50
–98
96
THD
40
93
t12 DELAY – ns
THD – dB
SNR – dB
–100
90
SNR
30
20
–102
87
10
84
–55
–35
–15
5
25
45
65
85
105
–104
125
0
0
TEMPERATURE – C
TPC 9. SNR and THD vs. Temperature
50
100
CL – pF
150
200
TPC 12. Typical Delay vs. Load Capacitance, CL
–10–
REV. B
AD7663
CIRCUIT INFORMATION
100000
The AD7663 is a fast, low power, single-supply, precise 16-bit
analog-to-digital converter (ADC). The AD7663 is capable of
converting 250,000 samples per second (250 kSPS) and allows
power saving between conversions. When operating at 100 SPS,
for example, it consumes typically only 15 µW. This feature
makes the AD7663 ideal for battery-powered applications.
OPERATING CURRENTS – A
10000
AVDD
1000
100
DVDD
10
1
The AD7663 provides the user with an on-chip track-and-hold,
successive approximation ADC that does not exhibit any pipeline
or latency, making it ideal for multiple multiplexed channel
applications.
OVDD
0.1
0.01
It is specified to operate with both bipolar and unipolar input
ranges by changing the connection of its input resistive scaler.
0.001
1
10
100
1000
10000
100000
1000000
SAMPLING RATE – SPS
TPC 13. Operating Currents vs. Sample Rate
The AD7663 can be operated from a single 5 V supply and can be
interfaced to either 5 V or 3 V digital logic. It is housed in a 48-lead
LQFP package or a 48-lead LFCSP package that combines space
savings and flexible configurations as either serial or parallel interface. The AD7663 is pin-to-pin compatible with the AD7660.
POWER-DOWN OPERATING CURRENTS – nA
500
CONVERTER OPERATION
450
400
350
DVDD
300
250
200
150
OVDD
100
AVDD
50
0
–55
–35
–15
5
25
45
TEMPERATURE – C
65
85
105
TPC 14. Power-Down Operating Currents vs. Temperature
10
6
–FS
OFFSET
LSB
2
0
+FS
–2
–4
–6
–8
–10
–55
–35
–15
5
25
During the acquisition phase, the common terminal of the array
tied to the comparator’s positive input is connected to AGND
via SWA. All independent switches are connected to the output
of the resistive scaler. Thus, the capacitor array is used as a
sampling capacitor and acquires the analog signal. Similarly, the
dummy capacitor acquires the analog signal on INGND input.
When the acquisition phase is complete and the CNVST input
goes or is LOW, a conversion phase is initiated. When the conversion phase begins, SWA and SWB are opened first. The capacitor
array and the dummy capacitor are then disconnected from the
inputs and connected to the REFGND input. Therefore, the differential voltage between the output of the resistive scaler and INGND
captured at the end of the acquisition phase is applied to the
comparator inputs, causing the comparator to become unbalanced.
8
4
The AD7663 is a successive approximation analog-to-digital
converter based on a charge redistribution DAC. Figure 3 shows
the simplified schematic of the ADC. The input analog signal is
first scaled down and level shifted by the internal input resistive
scaler, which allows both unipolar ranges (0 V to 2.5 V, 0 V to 5 V,
and 0 V to 10 V) and bipolar ranges (±2.5 V, ±5 V, and ±10 V).
The output voltage range of the resistive scaler is always 0 V to
2.5 V. The capacitive DAC consists of an array of 16 binary
weighted capacitors and an additional “LSB” capacitor. The
comparator’s negative input is connected to a “dummy” capacitor
of the same value as the capacitive DAC array.
45
65
85
105
125
TEMPERATURE – C
By switching each element of the capacitor array between
REFGND or REF, the comparator input varies by binary
weighted voltage steps (VREF /2, VREF /4 . . . VREF /65,536). The
control logic toggles these switches, starting with the MSB first,
in order to bring the comparator back into a balanced condition.
After the completion of this process, the control logic generates
the ADC output code and brings the BUSY output LOW.
TPC 15. +FS, Offset, and –FS vs. Temperature
REV. B
–11–
AD7663
4R
IND
REF
REFGND
4R
INC
2R
MSB
INB
32,768C 16,384C
LSB
4C
2C
C
SWA
SWITCHES
CONTROL
C
R
INA
BUSY
COMP
INGND
CONTROL
LOGIC
OUTPUT
CODE
65,536C
SWB
CNVST
Figure 3. ADC Simplified Schematic
ADC CODE – Straight Binary
Transfer Functions
Using the OB/2C digital input, the AD7663 offers two output
codings: straight binary and twos complement. The ideal transfer
characteristic for the AD7663 is shown in Figure 4 and Table III.
111...111
111...110
111...101
TYPICAL CONNECTION DIAGRAM
Figure 5 shows a typical connection diagram for the AD7663.
Different circuitry shown on this diagram is optional and is
discussed in the figure’s notes.
Analog Inputs
The AD7663 is specified to operate with six full-scale analog
input ranges. Connections required for each of the four analog
inputs, IND, INC, INB, and INA, and the resulting full-scale
ranges are shown in Table I. The typical input impedance for
each analog input range is also shown.
000...010
000...001
000...000
–FS
–FS + 1 LSB
+FS – 1 LSB
–FS + 0.5 LSB
+FS – 1.5 LSB
ANALOG INPUT
Figure 4. ADC Ideal Transfer Function
Table III. Output Codes and Ideal Input Voltages
Description
Digital Output
Code (Hexa)
Straight Twos
Binary Complement
Analog Input
1
Full-Scale Range
Least Significant Bit
FSR – 1 LSB
Midscale + 1 LSB
Midscale
Midscale – 1 LSB
–FSR + 1 LSB
–FSR
±10 V
305.2 µV
9.999695 V
305.2 µV
0V
–305.2 µV
–9.999695 V
–10 V
±5 V
152.6 µV
4.999847 V
152.6 µV
0V
–152.6 µV
–4.999847 V
–5 V
±2.5 V
76.3 µV
2.499924 V
76.3 µV
0V
–76.3 µV
–2.499924 V
–2.5 V
0 V to 10 V
152.6 µV
9.999847 V
5.000153 V
5V
4.999847 V
152.6 µV
0V
0 V to 5 V
76.3 µV
4.999924 V
2.570076 V
2.5 V
2.499924 V
76.3 µV
0V
0 V to 2.5 V
38.15 µV
2.499962 V
1.257038 V
1.25 V
1.249962 V
38.15 µV
0V
FFFF2
8001
8000
7FFF
0001
00003
7FFF2
0001
0000
FFFF
8001
80003
NOTES
1
Values with REF = 2.5 V, with REF = 3 V, all values will scale linearly.
2
This is also the code for an overrange analog input.
3
This is also the code for an underrange analog input.
–12–
REV. B
AD7663
DVDD
100
ANALOG
SUPPLY
(5V)
+
10F
ADR421
NOTE 7
100nF
AVDD
+
10F
AGND
100nF
100nF
DGND
DVDD
OVDD
DIGITAL SUPPLY
(3.3V OR 5V)
+
10F
OGND
SERIAL
PORT
REF
2.5V REF
NOTE 1
1M
+
50k
100nF
SCLK
CREF
NOTE 2
SDOUT
REFGND
BUSY
NOTE 3
50
AD7663
U2
+
CNVST
C/P/DSP
D
INA
+ 10F
NOTE 8
100nF
AD8031
OB/2C
NOTE 4
DVDD
50
SER/PAR
CLOCK
15
ANALOG
INPUT
(10V)
NOTE 5
U1
+
IND
AD8021
CC
2.7nF
CS
NOTE
6
RD
BYTESWAP
INGND
RESET
INB
PD
INC
NOTES
1. SEE VOLTAGE REFERENCE INPUT SECTION.
2. WITH THE RECOMMENDED VOLTAGE REFERENCES, CREF IS 47F. SEE VOLTAGE REFERENCE INPUT SECTION.
3. OPTIONAL CIRCUITRY FOR HARDWARE GAIN CALIBRATION.
4. FOR BIPOLAR RANGE ONLY. SEE SCALER REFERENCE INPUT SECTION.
5. THE AD8021 IS RECOMMENDED. SEE DRIVER AMPLIFIER CHOICE SECTION.
6. WITH 0V TO 2.5V RANGE ONLY. SEE ANALOG INPUTS SECTION.
7. OPTION. SEE POWER SUPPLY SECTION.
8. OPTIONAL LOW JITTER CNVST. SEE CONVERSION CONTROL SECTION.
Figure 5. Typical Connection Diagram (±10 V Range Shown)
Figure 6 shows a simplified analog input section of the AD7663.
AVDD
4R
IND
4R
INC
2R
INB
R
INA
R1
CS
R = 1.28k
AGND
Figure 6. Simplified Analog Input
The four resistors connected to the four analog inputs form a resistive scaler that scales down and shifts the analog input range to a
common input range of 0 V to 2.5 V at the input of the switched
capacitive ADC.
By connecting the four inputs INA, INB, INC, and IND to the
input signal itself, the ground, or a 2.5 V reference, other analog
input ranges can be obtained.
REV. B
The diodes shown in Figure 6 provide ESD protection for the four
analog inputs. The inputs INB, INC, and IND have a high voltage
protection (–11 V to +30 V) to allow wide input voltage range.
Care must be taken to ensure that the analog input signal never
exceeds the absolute ratings on these inputs, including INA
(0 V to 5 V). This will cause these diodes to become forwardbiased and start conducting current. These diodes can handle a
forward-biased current of 120 mA maximum. For instance, when
using the 0 V to 2.5 V input range, these conditions could eventually occur on the input INA when the input buffer’s (U1) supplies
are different from AVDD. In such cases, an input buffer with a
short-circuit current limitation can be used to protect the part.
This analog input structure allows the sampling of the differential
signal between the output of the resistive scaler and INGND. Unlike
other converters, the INGND input is sampled at the same time as
the inputs. By using this differential input, small signals common
to both inputs are rejected as shown in Figure 7, which represents
the typical CMRR over frequency. For instance, by using INGND
to sense a remote signal ground, the difference of ground potentials
between the sensor and the local ADC ground is eliminated.
–13–
AD7663
75
Driver Amplifier Choice
70
Although the AD7663 is easy to drive, the driver amplifier needs
to meet at least the following requirements:
• The driver amplifier and the AD7663 analog input circuit
65
have to be able, together, to settle for a full-scale step of the
capacitor array at a 16-bit level (0.0015%). In the amplifier’s
data sheet, the settling at 0.1% to 0.01% is more commonly
specified. It could significantly differ from the settling time at
16-bit level and, therefore, it should be verified prior to the
driver selection. The tiny op amp AD8021, which combines
ultralow noise and a high gain bandwidth, meets this settling
time requirement even when used with a high gain up to 13.
CMRR – dB
60
55
50
45
40
• The noise generated by the driver amplifier needs to be kept
35
0
10
100
as low as possible in order to preserve the SNR and transition
noise performance of the AD7663. The noise coming from
the driver is first scaled down by the resistive scaler according
to the analog input voltage range used, and is then filtered by
the AD7663 analog input circuit one-pole, low-pass filter
made by (R/2 + R1) and CS. The SNR degradation due to
the amplifier is
1000
FREQUENCY – kHz
Figure 7. Analog Input CMRR vs. Frequency
During the acquisition phase for ac signals, the AD7663 behaves
like a one-pole RC filter consisting of the equivalent resistance of
the resistive scaler R/2 in series with R1 and CS. The resistor R1
is typically 2700 W and is a lumped component made up of some
serial resistors and the on-resistance of the switches. The capacitor
CS is typically 60 pF and is mainly the ADC sampling capacitor.
This one-pole filter with a typical –3 dB cutoff frequency of
800 kHz reduces undesirable aliasing effects and limits the noise
coming from the inputs.
SNRLOSS
Except when using the 0 V to 2.5 V analog input voltage range,
the AD7663 has to be driven by a very low impedance source to
avoid gain errors. That can be done by using a driver amplifier
whose choice is eased by the primarily resistive analog input
circuitry of the AD7663.
Ê
ˆ
Á
˜
Á
˜
28
= 20 log Á
2 ˜
Ê 2.5 N eN ˆ ˜
Á 784 + p f
˜
–3 dB Á
Á
2
Ë FSR ¯ ˜¯
Ë
where:
f–3 dB is the –3 dB input bandwidth in MHz of the AD7663
(0.8 MHz) or the cut-off frequency of the input filter
if any used (0 V to 2.5 V range).
When using the 0 V to 2.5 V analog input voltage range, the input
impedance of the AD7663 is very high so the AD7663 can be
driven directly by a low impedance source without gain error.
That allows, as shown in Figure 5, putting an external one-pole
RC filter between the output of the amplifier output and the ADC
analog inputs to even further improve the noise filtering by the
AD7663 analog input circuit. However, the source impedance
has to be kept low because it affects the ac performances, especially
the total harmonic distortion (THD). The maximum source
impedance depends on the amount of THD that can be tolerated.
The THD degradation is a function of the source impedance
and the maximum input frequency as shown in Figure 8.
N
is the noise factor of the amplifier (1 if in buffer
configuration).
eN
is the equivalent input noise voltage of the op amp
in nV/Hz1/2.
FSR is the full-scale span (i.e., 5 V for ±2.5 V range).
For instance, when using the 0 V to 2.5 V range, a driver
like the AD8610 with an equivalent input noise of 6 nV/÷Hz
and configured as a buffer, thus with a noise gain of 1, the
SNR degrades by only 0.24 dB.
• The driver needs to have a THD performance suitable to
–70
that of the AD7663. TPC 10 gives the THD versus frequency
that the driver should preferably exceed.
The AD8021 meets these requirements and is usually appropriate for almost all applications. The AD8021 needs an external
compensation capacitor of 10 pF. This capacitor should have good
linearity as an NPO ceramic or mica type.
–80
THD
R = 100
–90
The AD8022 could also be used where a dual version is needed
and gain of 1 is used.
R = 50
R = 11
The AD829 is another alternative where high frequency (above
100 kHz) performance is not required. In a gain of 1, it requires
an 82 pF compensation capacitor.
–100
–110
10
100
FREQUENCY – kHz
1000
The AD8610 is also another option where low bias current is
needed in low frequency applications.
Figure 8. THD vs. Analog Input Frequency and Input
Resistance (0 V to 2.5 V Only)
–14–
REV. B
AD7663
Voltage Reference Input
Power Supply
The AD7663 uses an external 2.5 V voltage reference.
The AD7663 uses three sets of power supply pins: an analog 5 V
supply AVDD, a digital 5 V core supply DVDD, and a digital
input/output interface supply OVDD. The OVDD supply allows
direct interface with any logic working between 2.7 V and DVDD
+ 0.3 V. To reduce the number of supplies needed, the digital
core (DVDD) can be supplied through a simple RC filter from the
analog supply as shown in Figure 5. The AD7663 is independent
of power supply sequencing, once OVDD does not exceed DVDD
by more than 0.3 V, and thus free from supply voltage induced
latch-up. Additionally, it is very insensitive to power supply
variations over a wide frequency range as shown in Figure 9.
The voltage reference input REF of the AD7663 has a dynamic
input impedance; it should therefore be driven by a low impedance
source with an efficient decoupling between REF and REFGND
inputs. This decoupling depends on the choice of the voltage
reference but usually consists of a 1 µF ceramic capacitor and a
low ESR tantalum capacitor connected to the REF and REFGND
inputs with minimum parasitic inductance. 47 µF is an appropriate
value for the tantalum capacitor when used with one of the
recommended reference voltages:
• The low noise, low temperature drift ADR421 and AD780
110
voltage reference
105
• The low power ADR291 voltage reference
• The low cost AD1582 voltage reference
100
95
90
PSRR – dB
For applications using multiple AD7663s, it is more effective to
buffer the reference voltage with a low noise, very stable op amp
like the AD8031.
Care should also be taken with the reference temperature coefficient
of the voltage reference that directly affects the full-scale accuracy if this parameter matters. For instance, a ±15 ppm/°C
tempco of the reference changes the full scale by ±1 LSB/°C.
Note that VREF , as mentioned in the Specification tables, could be
increased to AVDD – 1.85 V. The benefit here is the increased
SNR obtained as a result of this increase. Since the input range is
defined in terms of VREF, this would essentially increase the ±REF
range from ±2.5 V to ±3 V and so on with an AVDD above
4.85 V. The theoretical improvement as a result of this increase
in reference is 1.58 dB (20 log [3/2.5]). Due to the theoretical
quantization noise, however, the observed improvement is approximately 1 dB. The AD780 can be selected with a 3 V reference
voltage.
Scaler Reference Input (Bipolar Input Ranges)
When using the AD7663 with bipolar input ranges, the connection
diagram in Figure 5 shows a reference buffer amplifier. This
buffer amplifier is required to isolate the REF pin from the signal
dependent current in the INx pin. A high speed op amp, such as
the AD8031, can be used with a single 5 V power supply without degrading the performance of the AD7663. The buffer must
have good settling characteristics and provide low total noise
within the input bandwidth of the AD7663.
85
80
75
70
65
60
55
50
1
10
100
1000
FREQUENCY – kHz
Figure 9. PSRR vs. Frequency
POWER DISSIPATION
The AD7663 automatically reduces its power consumption at
the end of each conversion phase. During the acquisition phase,
the operating currents are very low, which allows a significant
power savings when the conversion rate is reduced as shown in
Figure 10. This feature makes the AD7663 ideal for very low
power battery applications.
This does not take into account the power, if any, dissipated by
the input resistive scaler that depends on the input voltage range
used and the analog input voltage even in power-down mode.
There is no power dissipated when the 0 V to 2.5 V is used or
when both the analog input voltage is 0 V and a unipolar range,
0 V to 5 V or 0 V to 10 V, is used.
It should be noted that the digital interface remains active even
during the acquisition phase. To reduce the operating digital
supply currents even further, the digital inputs need to be driven
close to the power rails (i.e., DVDD and DGND) and OVDD
should not exceed DVDD by more than 0.3 V.
REV. B
–15–
AD7663
For other applications, conversions can be automatically initiated.
If CNVST is held low when BUSY is low, the AD7663 controls
the acquisition phase and then automatically initiates a new
conversion. By keeping CNVST low, the AD7663 keeps the
conversion process running by itself. It should be noted that the
analog input has to be settled when BUSY goes low. Also, at
power-up, CNVST should be brought low once to initiate the
conversion process. In this mode, the AD7663 could sometimes
run slightly faster than the guaranteed limit of 250 kSPS.
100k
POWER DISSIPATION – ␮W
10k
1k
100
10
t9
1
RESET
0.1
1
10
100
1k
10k
SAMPLING RATE – SPS
100k
1M
BUSY
Figure 10. Power Dissipation vs. Sample Rate
CONVERSION CONTROL
Figure 11 shows the detailed timing diagrams of the conversion
process. The AD7663 is controlled by the signal CNVST, which
initiates conversion. Once initiated, it cannot be restarted or
aborted, even by the power-down input PD, until the conversion is
complete. The CNVST signal operates independently of CS and
RD signals.
DATA BUS
t8
CNVST
Figure 12. RESET Timing
t2
DIGITAL INTERFACE
t1
The AD7663 has a versatile digital interface; it can be interfaced
with the host system by using either a serial or parallel interface.
The serial interface is multiplexed on the parallel data bus. The
AD7663 digital interface also accommodates both 3 V or 5 V
logic by simply connecting the OVDD supply pin of the AD7663
to the host system interface digital supply. Finally, by using the
OB/2C input pin, twos complement and straight binary coding
can be used.
CNVST
BUSY
t4
t3
t6
t5
MODE ACQUIRE
CONVERT
t7
ACQUIRE
CONVERT
t8
Figure 11. Basic Conversion Timing
For a true sampling application, the recommended operation of
the CNVST signal is the following.
The two signals CS and RD control the interface. When at least
one of these signals is HIGH, the interface outputs are in high
impedance. Usually, CS allows the selection of each AD7663 in
multicircuit applications and is held LOW in a single AD7663
design. RD is generally used to enable the conversion result on
the data bus.
CNVST must be held HIGH from the previous falling edge of
BUSY and during a minimum delay corresponding to the acquisition time t8. Then, when CNVST is brought LOW, a conversion is
initiated and the BUSY signal goes HIGH until the completion
of the conversion. Although CNVST is a digital signal, it should
be designed with special care with fast, clean edges, and levels
with minimum overshoot and undershoot or ringing. It is a good
thing to shield the CNVST trace with ground and also to add a
low value serial resistor (i.e., 50 W) termination close to the output
of the component that drives this line. For applications where
the SNR is critical, the CNVST signal should have a very low
jitter. To achieve this, some use a dedicated oscillator for
CNVST generation, or at least to clock it with a high frequency,
low jitter clock as shown in Figure 5.
–16–
CS = RD = 0
t1
CNVST
t 10
BUSY
t3
DATA BUS
t4
t 11
PREVIOUS CONVERSION DATA
NEW DATA
Figure 13. Master Parallel Data Timing for Reading
(Continuous Read)
REV. B
AD7663
PARALLEL INTERFACE
CS
The AD7663 is configured to use the parallel interface when
the SER/PAR is held LOW. The data can be read either after
each conversion, which is during the next acquisition phase, or
during the following conversion as shown, respectively, in
Figures 14 and 15. When the data is read during the conversion,
however, it is recommended that it be read-only during the
first half of the conversion phase. That avoids any potential
feedthrough between voltage transients on the digital interface and
the most critical analog conversion circuitry.
RD
BYTE
PINS D[15:8]
HI-Z
HIGH BYTE
HI-Z
LOW BYTE
HI-Z
t13
t12
t12
PINS D[7:0]
LOW BYTE
HIGH BYTE
HI-Z
CS
Figure 16. 8-Bit Parallel Interface
RD
SERIAL INTERFACE
The AD7663 is configured to use the serial interface when the
SER/PAR is held HIGH. The AD7663 outputs 16 bits of data,
MSB first, on the SDOUT pin. This data is synchronized with
the 16 clock pulses provided on the SCLK pin. The output data
is valid on both the rising and falling edge of the data clock.
BUSY
CURRENT
CONVERSION
DATA BUS
t 12
t 13
Figure 14. Slave Parallel Data Timing for Reading (Read
after Convert)
CS = 0
t1
CNVST,
RD
BUSY
t4
t3
PREVIOUS
CONVERSION
DATA BUS
t 12
t 13
Figure 15. Slave Parallel Data Timing for Reading (Read
during Convert)
The BYTESWAP pin allows a glueless interface to an 8-bit bus.
As shown in Figure 16, the LSB byte is output on D[7:0] and
the MSB is output on D[15:8] when BYTESWAP is LOW.
When BYTESWAP is HIGH, the LSB and MSB are swapped
and the LSB is output on D[15:8] and the MSB is output on
D[7:0]. By connecting BYTESWAP to an address line, the 16
data bits can be read in two bytes on either D[15:8] or D[7:0].
REV. B
MASTER SERIAL INTERFACE
Internal Clock
The AD7663 is configured to generate and provide the serial data
clock SCLK when the EXT/INT pin is held LOW. It also generates
a SYNC signal to indicate to the host when the serial data is valid.
The serial clock SCLK and the SYNC signal can be inverted if
desired. Depending on RDC/SDIN input, the data can be read
after each conversion or during the following conversion. Figures 17
and 18 show the detailed timing diagrams of these two modes.
Usually, because the AD7663 has a longer acquisition phase
than the conversion phase, the data is read immediately after
conversion. That makes the mode master, read after conversion,
the most recommended Serial Mode when it can be used.
In Read-during-Conversion Mode, the serial clock and data
toggle at appropriate instants that minimize potential feedthrough
between digital activity and the critical conversion decisions.
In Read-after-Conversion Mode, it should be noted that unlike
in other modes, the signal BUSY returns LOW after the 16 data
bits are pulsed out and not at the end of the conversion phase,
which results in a longer BUSY width. In this mode, if necessary, the internal clock can be slowed down by a ratio selected
by the DIVSCLK inputs according to Table II.
–17–
AD7663
EXT/INT = 0
CS, RD
RDC/SDIN = 0
INVSCLK = INVSYNC = 0
t3
CNVST
t 28
BUSY
t 30
t 29
t 25
SYNC
t 14
t 18
t 19
t 20
t 24
t 21
t 26
1
2
D15
D14
SCLK
3
14
15
16
t 15
t 27
SDOUT
X
t 16
D2
D1
D0
t 23
t 22
Figure 17. Master Serial Data Timing for Reading (Read after Convert)
RDC/SDIN = 1
EXT/INT = 0
CS, RD
INVSCLK = INVSYNC = 0
t1
CNVST
t3
BUSY
t 17
t 25
SYNC
t 14
t 19
t 20 t 21
t 15
SCLK
1
t 24
2
3
14
15
t 18
SDOUT
X
t 16
t 22
t 26
16
t 27
D15
D14
D2
D1
D0
t 23
Figure 18. Master Serial Data Timing for Reading (Read Previous Conversion during Convert)
–18–
REV. B
AD7663
EXT/INT = 1
RD = 0
INVSCLK = 0
CS
BUSY
t36
SCLK
t35
t37
1
2
t31
3
14
15
16
17
18
t32
X
SDOUT
t16
D15
D14
D13
D1
D0
X15
X14
X14
X13
X1
X0
Y15
Y14
t34
SDIN
X15
t33
Figure 19. Slave Serial Data Timing for Reading (Read after Convert)
SLAVE SERIAL INTERFACE
External Clock
The AD7663 is configured to accept an externally supplied
serial data clock on the SCLK pin when the EXT/INT pin is
held HIGH. In this mode, several methods can be used to read
the data. The external serial clock is gated by CS and the data
are output when both CS and RD are LOW. Thus, depending
on CS, the data can be read after each conversion or during the
following conversion. The external clock can be either a continuous or discontinuous clock. A discontinuous clock can be either
normally high or normally low when inactive. Figures 19 and 21
show the detailed timing diagrams of these methods.
While the AD7663 is performing a bit decision, it is important
that voltage transients not occur on digital input/output pins or
degradation of the conversion result could occur. This is particularly important during the second half of the conversion
phase because the AD7663 provides error correction circuitry
that can correct for an improper bit decision made during the first
half of the conversion phase. For this reason, it is recommended
that when an external clock is being provided, it is a discontinuous
clock that is toggling only when BUSY is LOW or, more
importantly, that does not transition during the latter half of
BUSY HIGH.
Another advantage is to be able to read the data at any speed up
to 40 MHz, which accommodates both slow digital host interface
and the fastest serial reading.
Finally, in this mode only, the AD7663 provides a “daisy-chain”
feature using the RDC/SDIN input pin for cascading multiple
converters together. This feature is useful for reducing component
count and wiring connections when desired as, for instance, in
isolated multiconverter applications.
An example of the concatenation of two devices is shown in
Figure 20. Simultaneous sampling is possible by using a common CNVST signal. It should be noted that the RDC/SDIN
input is latched on the opposite edge of SCLK of the one used
to shift out the data on SDOUT. Therefore, the MSB of the
“upstream” converter just follows the LSB of the “downstream”
converter on the next SCLK cycle.
BUSY
OUT
BUSY
BUSY
AD7663
AD7663
#2
(UPSTREAM)
#1
(DOWNSTREAM)
RDC/SDIN
External Discontinuous Clock Data Read after Conversion
This mode is the most recommended of the serial slave modes.
Figure 19 shows the detailed timing diagrams of this method.
After a conversion is complete, indicated by BUSY returning
LOW, the result of this conversion can be read while both CS and
RD are LOW. The data is shifted out, MSB first, with 16 clock
pulses and is valid on both the rising and falling edge of the clock.
RDC/SDIN
SDOUT
CNVST
CNVST
CS
CS
SCLK
SCLK
DATA
OUT
SCLK IN
CS IN
CNVST IN
Among the advantages of this method, the conversion performance
is not degraded because there are no voltage transients on the
digital interface during the conversion process.
REV. B
SDOUT
Figure 20. Two AD7663s in a Daisy-Chain Configuration
–19–
AD7663
RD = 0
INVSCLK = 0
EXT/INT = 1
CS
CNVST
BUSY
t3
t 35
t 36 t 37
SCLK
1
2
t 31
14
15
16
t 32
X
SDOUT
3
D15
D14
D13
D1
D0
t 16
Figure 21. Slave Serial Data Timing for Reading (Read Previous Conversion during Convert)
External Clock Data Read during Conversion
Figure 21 shows the detailed timing diagrams of this method.
During a conversion, while both CS and RD are LOW, the result
of the previous conversion can be read. The data is shifted out
MSB first with 16 clock pulses, and is valid on both the rising and
the falling edge of the clock. The 16 bits have to be read before
the current conversion is complete. If that is not done, RDERROR
is pulsed HIGH and can be used to interrupt the host interface
to prevent an incomplete data reading. There is no daisy-chain
feature in this mode, and RDC/SDIN input should always be
tied either HIGH or LOW.
peripheral interface (SPI) on the MC68HC11 is configured for
Master Mode (MSTR) = 1, Clock Polarity Bit (CPOL) = 0, Clock
Phase Bit (CPHA) = 1, and SPI interrupt enable (SPIE) = 1
by writing to the SPI Control Register (SPCR). The IRQ is
configured for edge-sensitive-only operation (IRQE = 1 in
OPTION register).
DVDD
AD7663*
MC68HC11*
SER/PAR
EXT/INT
CS
To reduce performance degradation due to digital activity, a
fast discontinuous clock of at least 25 MHz is recommended to
ensure that all the bits are read during the first half of the conversion phase.
RD
BUSY
SDOUT
SCLK
INVSCLK
MICROPROCESSOR INTERFACING
CNVST
IRQ
MISO/SDI
SCK
I/O PORT
*ADDITIONAL PINS OMITTED FOR CLARITY
The AD7663 is ideally suited for traditional dc measurement
applications supporting a microprocessor and ac signal processing
applications interfacing to a digital signal processor. The
AD7663 is designed to interface with either a parallel 8-bit or
16-bit wide interface or with a general-purpose Serial Port or I/O
Ports on a microcontroller. A variety of external buffers can be
used with the AD7663 to prevent digital noise from coupling into
the ADC. The following sections illustrate the use of the AD7663
with an SPI equipped microcontroller, the ADSP-21065L and
ADSP-218x signal processors.
SPI Interface (MC68HC11)
Figure 22 shows an interface diagram between the AD7663 and an
SPI-equipped microcontroller, such as the MC68HC11. To
accommodate the slower speed of the microcontroller, the AD7663
acts as a slave device and data must be read after conversion. This
mode also allows the daisy-chain feature. The convert command
could be initiated in response to an internal timer interrupt. The
reading of output data, one byte at a time if necessary, could be
initiated in response to the end-of-conversion signal (BUSY going
LOW) using an interrupt line of the microcontroller. The serial
Figure 22. Interfacing the AD7663 to SPI Interface
ADSP-21065L in Master Serial Interface
As shown in Figure 23, the AD7663 can be interfaced to the
ADSP-21065L using the serial interface in Master Mode without
any glue logic required. This mode combines the advantages of
reducing the wire connections and being able to read the data during
or after conversion at maximum speed transfer (DIVSCLK[0:1]
both low.
The AD7663 is configured for the Internal Clock Mode (EXT/INT
low) and acts therefore as the master device. The convert command can be generated by an external low jitter oscillator or, as
shown, by a FLAG output of the ADSP-21065L, or by a frame
output TFS of one Serial Port of the ADSP-21065L that can be used
like a timer. The Serial Port on the ADSP-21065L is configured
for external clock (IRFS = 0), rising edge active (CKRE = 1),
external late framed sync signals (IRFS = 0, LAFS = 1,
RFSR = 1), and active HIGH (LRFS = 0). The Serial Port of
the ADSP-21065L is configured by writing to its receive control
register (SRCTL)—see ADSP-2106x SHARC User’s Manual.
–20–
REV. B
AD7663
Because the Serial Port within the ADSP-21065L will be seeing a
discontinuous clock, an initial word reading has to be done after
the ADSP-21065L has been reset to ensure that the Serial Port
is properly synchronized to this clock during each following data
read operation.
DVDD
AD7663*
ADSP-21065L*
SHARC
SER/PAR
RDC/SDIN
RD
EXT/INT
CS
SYNC
SDOUT
INVSYNC
SCLK
INVSCLK
CNVST
RFS
DR
RCLK
FLAG OR TFS
*ADDITIONAL PINS OMITTED FOR CLARITY
Figure 23. Interfacing to the ADSP-21065L Using the
Serial Master Mode
APPLICATION HINTS
Layout
The AD7663 has very good immunity to noise on the power
supplies as can be seen in Figure 9. However, care should still be
taken with regard to grounding layout.
The printed circuit board that houses the AD7663 should be
designed so the analog and digital sections are separated and confined to certain areas of the board. This facilitates the use of
ground planes that can be easily separated. Digital and analog
ground planes should be joined in only one place, preferably
underneath the AD7663 or at least as close as possible to the
AD7663. If the AD7663 is in a system where multiple devices
require analog-to-digital ground connections, the connection
should still be made at one point only, a star ground point that
should be established as close as possible to the AD7663.
It is recommended to avoid running digital lines under the device
as these will couple noise onto the die. The analog ground plane
should be allowed to run under the AD7663 to avoid noise coupling. Fast switching signals like CNVST or clocks should be
shielded with digital ground to avoid radiating noise to other
sections of the board and should never run near analog signal paths.
Crossover of digital and analog signals should be avoided. Traces
REV. B
on different but close layers of the board should run at right
angles to each other. This will reduce the effect of feedthrough
through the board.
The power supply lines to the AD7663 should use as large a trace
as possible to provide low impedance paths and reduce the effect of
glitches on the power supply lines. Good decoupling is also important to lower the supplies’ impedance presented to the AD7663
and to reduce the magnitude of the supply spikes. Decoupling
ceramic capacitors, typically 100 nF, should be placed on all of
the power supply pins AVDD, DVDD, and OVDD close to, and
ideally right up against these pins and their corresponding ground
pins. Additionally, low ESR 10 µF capacitors should be located
in the vicinity of the ADC to further reduce low frequency ripple.
The DVDD supply of the AD7663 can be either a separate
supply or come from the analog supply, AVDD, or from the
digital interface supply, OVDD. When the system digital supply
is noisy or fast switching digital signals are present, it is recommended, if no separate supply is available, to connect the DVDD
digital supply to the analog supply, AVDD, through an RC filter
as shown in Figure 5, and to connect the system supply to the
interface digital supply OVDD and the remaining digital circuitry.
When DVDD is powered from the system supply, it is useful to
insert a bead to further reduce high frequency spikes.
The AD7663 has five different ground pins: INGND, REFGND,
AGND, DGND, and OGND. INGND is used to sense the
analog input signal. REFGND senses the reference voltage and
should be a low impedance return to the reference because it
carries pulsed currents. AGND is the ground to which most internal
ADC analog signals are referenced. This ground must be connected with the least resistance to the analog ground plane. DGND
must be tied to the analog or digital ground plane depending on
the configuration. OGND is connected to the digital system ground.
The layout of the decoupling of the reference voltage is important.
The decoupling capacitor should be close to the ADC and connected with short and large traces to minimize parasitic inductances.
Evaluating the AD7663 Performance
A recommended layout for the AD7663 is outlined in the evaluation board for the AD7663. The evaluation board package includes
a fully assembled and tested evaluation board, documentation,
and software for controlling the board from a PC via the EvalControl Board.
–21–
AD7663
OUTLINE DIMENSIONS
48-Lead Low Profile Quad Flat Package [LQFP]
(ST-48)
Dimensions shown in millimeters
0.75
0.60
0.45
9.00 BSC
SQ
1.60
MAX
37
48
36
1
10
6
2
1.45
1.40
1.35
0.15
0.05
SEATING
PLANE
PIN 1
SEATING
PLANE
7.00
BSC SQ
TOP VIEW
0.20
0.09
(PINS DOWN)
VIEW A
7
3.5
0
0.10 MAX
COPLANARITY
25
12
13
24
0.27
0.22
0.17
0.50
BSC
VIEW A
ROTATED 90 CCW
COMPLIANT TO JEDEC STANDARDS MS-026BBC
48-Lead Lead Frame Chip Scale Package [LFCSP]
(CP-48)
Dimensions shown in millimeters
7.00
BSC SQ
0.60 MAX
0.60 MAX
37
6.75
BSC SQ
TOP
VIEW
0.20
REF
12 MAX
1
25
24
12
13
5.50
REF
0.80 MAX
0.65 NOM
0.05 MAX
0.02 NOM
0.50 BSC
SEATING
PLANE
5.25
5.10 SQ
4.95
BOTTOM
VIEW
0.50
0.40
0.30
1.00
0.90
0.80
PIN 1
INDICATOR
48
36
PIN 1
INDICATOR
0.30
0.23
0.18
PADDLE CONNECTED TO AGND.
THIS CONNECTION IS NOT
REQUIRED TO MEET THE
ELECTRICAL PERFORMANCES
COPLANARITY
0.08
COMPLIANT TO JEDEC STANDARDS MO-220-VKKD-2
–22–
REV. B
AD7663
Revision History
Location
Page
4/03—Data Sheet changed from REV. A to REV. B.
Changes to PulSAR Selection table . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Changes to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Updated OUTLINE DIMENSIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
5/02—Data Sheet changed from REV. 0 to REV. A.
Edits to FEATURES . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to GENERAL DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Chart added to PRODUCT HIGHLIGHTS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Edits to SPECIFICATIONS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2–3
Edits to Table I . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
Edits to ABSOLUTE MAXIMUM RATINGS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Edits to ORDERING GUIDE . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 5
Edits to PIN FUNCTION DESCRIPTION . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6
Addition of TPC 15 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Edits to CIRCUIT INFORMATION section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 11
Edits to Table III . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12
Edits to Voltage Reference Input and Power Supply sections . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 15
Edits to ADSP-21065L in Master Serial Interface section . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 20
New Package Outline Added . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 22
REV. B
–23–
–24–
C01845–0–5/03(B)