MAXIM MAX8844YETD+

19-4279; Rev 0; 3/09
EVALUATION KIT
AVAILABLE
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
Applications
Cellular and Cordless
Phones
Features
♦ CCCV, Thermally Regulated Linear One-Cell Li+
Battery Charger
♦ No External MOSFET, Reverse Blocking Diode, or
Current-Sense Resistor
♦ Programmable Fast-Charge Currents (1ARMS max)
♦ Programmable Top-Off Current Threshold
♦ Input Overvoltage Protected 4.7V Output
(SAFEOUT) from IN
♦ Input Overvoltage Protected 4.7V Output
(SAFEUSB) from USB
♦ Proprietary Die Temperature Regulation Control
(+115°C)
♦ 4.25V to 28V Input Voltage Range with Input
Overvoltage Protection Above +7.5V
♦ Low-Dropout Voltage (300mV at 500mA)
♦ Input Power-Source Detection Output (POK),
Charge Status Output (CHG), Charge-Enable Input
(EN)
♦ Output for Autobooting (ABO, MAX8844Z)
♦ Output for Autobooting (ABO, MAX8844Y)
♦ Tiny 3mm x 3mm, 14-Pin TDFN Package, 0.8mm
Height (max)
Ordering Information
PART
PINPACKAGE
TOP MARK
ABO
ACTIVE
STATE
MAX8844ZETD+
14 TDFN-EP*
AEK
Active high
MAX8844YETD+
14 TDFN-EP*
AEN
Active low
+Denotes a lead(Pb)-free/RoHS-compliant package.
*EP = Exposed pad.
Note: All devices are specified over the -40°C to +85°C operating temperature range.
USB Appliances
Smart Phones and PDAs
Charging Cradles and
Docks
Digital Still Cameras
Bluetooth® Equipment
Typical Operating Circuit and Pin Configuration appear at
end of data sheet.
MP3 Players
Bluetooth is a registered trademark of Bluetooth SIG.
________________________________________________________________ Maxim Integrated Products
For pricing, delivery, and ordering information, please contact Maxim Direct at 1-888-629-4642,
or visit Maxim’s website at www.maxim-ic.com.
1
MAX8844Z/MAX8844Y
General Description
The MAX8844Z/MAX8844Y intelligent, stand-alone constant-current, constant-voltage (CCCV), thermally regulated dual input linear chargers are designed for
charging a single-cell lithium-ion (Li+) battery. The
MAX8844Z/MAX8844Y integrate a current-sense circuit,
MOSFET pass element, thermal-regulation circuitry,
and eliminate the external reverse-blocking Schottky
diode to create the simplest and smallest charging
solutions for handheld equipment.
The IC controls the charging sequence from the prequalification state through constant current fast-charge,
top-off charge, and full-charge indication. Proprietary
thermal-regulation circuitry limits the die temperature
during fast-charging or when the IC is exposed to high
ambient temperatures, allowing maximum charging
current without damaging the IC.
The MAX8844Z/MAX8844Y achieve high flexibility by providing adjustable fast-charge currents (SETI) and an
adjustable top-off current threshold (MIN) through external
resistors. The IC features a booting assistant circuit that
distinguishes input sources and battery connection and
provides an enable signal (ABO, ABO) for system booting.
The ICs also integrate two input overvoltage-protected
LDO outputs (SAFEOUT, SAFEUSB) for low-voltagerated USB or charger inputs in system, and a battery
pack detection circuit (DETBAT) that disables the charger when the battery pack is absent. Other features
include an active-low control input (EN), an active-low
input power source detection output (POK), and a fully
charged top-off threshold detection output (CHG).
The MAX8844Z/MAX8844Y automatically select between
either the USB or IN source. If both sources are present
at the same time, highest priority is given to the IN source.
The IN source is selected to ensure the shortest charging
time for the system since it is able to deliver the highest
current.
The MAX8844Z/MAX8844Y accept an input supply range
from 4.25V to 28V (IN and USB), but disable charging if
the input voltage exceeds +7.5V to protect against
unqualified or faulty AC adapters. The ICs operate over
the extended temperature range (-40°C to +85°C) and are
available in a compact 14-pin, thermally enhanced, leadfree TDFN 3mm x 3mm package (0.8mm max height).
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
ABSOLUTE MAXIMUM RATINGS
IN, USB to GND......................................................-0.3V to +30V
ABI, BATT, EN, POK, ABO, ABO, CHG, DETBAT, SETI,
MIN, SAFEOUT,
SAFEUSB to GND.................................................-0.3V to +6V
IN to BATT Continuous Current .........................................1ARMS
Continuous Power Dissipation (TA = +70°C)
14 TDFN (derate 24.4mW/°C above 70°C)
(multilayer PCB) ....................................................1951.2mW
BATT Short-Circuit Duration .......................................Continuous
Operating Temperature Range ...........................-40°C to +85°C
Junction Temperature ......................................................+150°C
Storage Temperature Range .............................-65°C to +150°C
Lead Temperature (soldering, 10s) .................................+300°C
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional
operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to
absolute maximum rating conditions for extended periods may affect device reliability.
ELECTRICAL CHARACTERISTICS
(VIN = 5V or VUSB = 5V, VBATT = 4V, RPOK = 1MΩ to BATT, EN = unconnected, RSETI = 2.8kΩ to GND, VDETBAT = 0V, CBATT =
2.2µF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
CONDITIONS
MIN
TYP
MAX
UNITS
0
28
V
4.25
7.00
V
7.5
8.0
V
Constant current charging
IIN - IBATT, IBATT = 0A
0.25
0.50
Constant current charging
IIN - IBATT, IBATT = 500mA
1
IN, USB
Input Supply Voltage Range
Input Supply Operating Voltage
Range
Overvoltage Lockout Trip
Threshold
Input Current
VIN rising, 100mV hysteresis (typ)
7.0
IC disabled, V EN = 5V
VIN = 4V,
VBATT = 4.2V
0.23
TA = +25°C
0.02
TA = +85°C
0.03
mA
0.50
BATT, CHG, POK
Minimum BATT Bypass
Capacitance
2.2
VBATT Prequalification Threshold
Voltage
VBATT rising, 100mV hysteresis (typ)
Battery Regulation Voltage
IBATT = 0A
Regulator Dropout Voltage (VIN VBATT )
VBATT = 4.1V, IBATT = 425mA
BATT Input Current
(Note 2)
Current-Sense Amplifier Gain
(IBATT to ISETI)
2
2.3
2.5
2.7
TA = 0°C to +85°C
4.175
4.200
4.225
TA = -40°C to +85°C
4.158
4.200
4.242
260
VIN = 0 to 4V,
VBATT = 4.2V
5
IC disabled
3
IBATT = 500mA
µF
TA = 0°C to +85°C
1120
TA = -40°C to +85°C
1120
_______________________________________________________________________________________
V
V
mV
10
µA
µA/A
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
(VIN = 5V or VUSB = 5V, VBATT = 4V, RPOK = 1MΩ to BATT, EN = unconnected, RSETI = 2.8kΩ to GND, VDETBAT = 0V, CBATT =
2.2µF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
PARAMETER
Fast-Charge Current
USB Fast-Charge Current
CONDITIONS
MIN
TYP
MAX
TA = 0°C to +85°C
400
440
480
TA = -40°C to +85°C
375
440
505
VBATT = 3.5V,
RSETI = 14kΩ
74
88
102
MAX8844Z
332
380
418
MAX8844Y
405
450
495
VBATT = 3.5V,
RSETI = 2.8kΩ
UNITS
mA
mA
CHG Top-Off Threshold
IBATT falling, battery is charged, RMIN = 1.75kΩ (Note 3)
99
mA
CHG Hysteresis
IBATT rising after top-off is detected, RMIN = 1.75kΩ
27
mA
CHG Detection Delay
IBATT falls below top-off threshold
Prequalification Charge Current
Percentage of the fast-charge current, VBATT = 2.2V,
TA = 0°C to +85°C
CHG, POK Output Low Threshold
IPOK = 5mA , ICHG = 5mA
CHG, POK Output High Leakage
Current
V POK = 5.5V, V CHG = 5.5V
POK Threshold
(Note 2)
VIN - VBATT
4.0
6.2
10.7
ms
5
11
17
%
0.4
V
TA = +25°C
1
TA = +85°C
0.002
VIN rising
40
VIN falling
30
µA
mV
DETBAT, SAFEOUT, SAFEUSB
DETBAT Logic Input Low
Threshold
0.4
V
DETBAT Logic Input High
Threshold
DETBAT Pullup Resistor
1.3
DETBAT to VL = 3V
Minimum SAFEOUT Bypass
Capacitance
SAFEOUT Regulated Output
ISAFEOUT = 30mA, VIN = 5V, TA = 0°C to +85°C
4.5
SAFEOUT Current Limit
Minimum SAFEUSB Bypass
Capacitance
SAFEUSB Regulated Output
ISAFEUSB = 30mA, VUSB = 5V, TA = 0°C to +85°C
4.5
SAFEUSB Current Limit
470
kΩ
1
µF
4.7
4.9
V
100
mA
1
µF
4.7
4.9
100
V
mA
EN, ABI, ABO, ABO
EN, ABI Internal Pulldown
Resistor
100
EN, Logic Input Low Threshold
(Note 2)
4.25V ≤ VIN ≤ 7V
EN, Logic Input High Theshold
(Note 2)
4.25V ≤ VIN ≤ 7V
1.3
200
400
kΩ
0.4
V
V
_______________________________________________________________________________________
3
MAX8844Z/MAX8844Y
ELECTRICAL CHARACTERISTICS (continued)
ELECTRICAL CHARACTERISTICS (continued)
(VIN = 5V or VUSB = 5V, VBATT = 4V, RPOK = 1MΩ to BATT, EN = unconnected, RSETI = 2.8kΩ to GND, VDETBAT = 0V, CBATT =
2.2µF, TA = -40°C to +85°C, unless otherwise noted. Typical values are at TA = +25°C.) (Note 1)
ABI Logic Input Low Threshold
VBATT = 4V, VIN = 0V
ABI Logic Input High Threshold
VBATT = 4V, VIN = 0V
ABO Output Low Threshold
IABO(SINK) = 1mA
ABO Output High Threshold
IABO(SOURCE) = 1mA
ABO Output Low Threshold
Open drain, IABO(SINK) = 1mA
ABO Output High Threshold
Open drain, 100kΩ pullup on BATT
0.4
1.3
V
V
0.4
VBATT 0.4V
V
V
0.4
VBATT 0.4V
THERMAL
Die Temperature Regulation
Threshold
115
°C
Note 1: Specifications are 100% production tested at TA = +25°C. Limits over the operating temperature range are guaranteed by
design and characterization.
Note 2: The IN input supply and USB input supply are interchangeable (VIN = VUSB). See the DC and USB Power Supplies section
for further details.
Note 3: See the Top-Off Current Threshold Setting section for further details.
Typical Operating Characteristics
(VIN = 5V or VUSB = 5V, VBATT = 4V, R POK = RCHG = 200kΩ to 5V, EN = unconnected, RSETI = 2.8kΩ to GND, RMIN = 1.74kΩ to
GND, RDETBAT = 4.7kΩ to GND, CBATT = 2.2µF, TA = +25°C, unless otherwise noted.
VEN = 5V
0.5
SUPPLY CURRENT (mA)
0.8
0.6
0.7
0.6
0.5
0.4
0.3
0.2
0.4
0.3
0.2
0.1
0
0
4
8
12
16
20
INPUT VOLTAGE (V)
4
24
28
700
VIN = 5V,
VUSB = 0V
600
500
400
300
VIN = 0V,
VUSB = 5V
200
100
0.1
0
800
CHARGE CURRENT (mA)
VEN = 0V,
IBATT = 0A,
VIN RISING
0.9
MAX8844 toc01
1.0
CHARGE CURRENT
vs. BATTERY VOLTAGE
MAX8844 toc03
DISABLED MODE SUPPLY CURRENT
vs. INPUT VOLTAGE
MAX8844 toc02
SUPPLY CURRENT
vs. INPUT VOLTAGE
SUPPLY CURRENT (mA)
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
0
0
4
8
12
16
20
INPUT VOLTAGE (V)
24
28
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
BATTERY VOLTAGE (V)
_______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
200
400
300
100
0
0
8
12
16
20
24
VUSB - VBATT
200
100
4
ISAFEOUT = 1mA
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
VBATT = 4V
VSUPPLY RISING
0.5
0
0
28
100
200
300
400
500
600
0
4
8
12
16
20
24
INPUT VOLTAGE (V)
VSUPPLY - VBATT (mV)
INPUT VOLTAGE (V)
SAFEOUT OUTPUT VOLTAGE
vs. LOAD CURRENT
SAFEUSB OUTPUT VOLTAGE
vs. USB VOLTAGE
SAFEUSB OUTPUT VOLTAGE
vs. LOAD CURRENT
5
SAFEUSB VOLTAGE (V)
4.0
3.5
3.0
2.5
2.0
1.5
4
3
2
1.0
5.0
4.5
4.0
SAFEUSB VOLTAGE (V)
4.5
28
MAX8844 toc09
6
MAX8844 toc07
5.0
MAX8844 toc06
MAX8844 toc05
500
SAFEOUT VOLTAGE (V)
300
5.0
MAX8844 toc08
CHARGE CURRENT (mA)
VIN = 0V,
VUSB = 5V
0
SAFEOUT VOLTAGE (V)
VIN - VBATT
CHARGE CURRENT (mA)
VIN = 5V,
VUSB = 0V
400
600
MAX8844 toc04
600
500
SAFEOUT OUTPUT VOLTAGE
vs. INPUT VOLTAGE
CHARGE CURRENT
vs. SUPPLY VOLTAGE HEADROOM
CHARGE CURRENT
vs. INPUT VOLTAGE
3.5
3.0
2.5
2.0
1.5
1.0
1
0.5
0.5
0
0
0
0
20
40
60
80
0
100
4
8
12
16
20
24
28
0
40
60
80
100
SHUTDOWN
(FAST-CHARGE TO SHUTDOWN)
STARTUP INTO PRECHARGE
MAX8844 toc10
MAX8844 toc11
100mA/div
0
IBATT
20
LOAD CURRENT (mA)
USB VOLTAGE (V)
LOAD CURRENT (mA)
VIN
5V/div
VEN
0
5V/div
0
500mA/div
IBATT
0
5V/div
VIN
0
5V/div
VEN
0
5V/div
5V/div
VPOK
VPOK
0
0
40μs/div
100μs/div
_______________________________________________________________________________________
5
MAX8844Z/MAX8844Y
Typical Operating Characteristics (continued)
(VIN = 5V or VUSB = 5V, VBATT = 4V, R POK = RCHG = 200kΩ to 5V, EN = unconnected, RSETI = 2.8kΩ to GND, RMIN = 1.74kΩ to
GND, RDETBAT = 4.7kΩ to GND, CBATT = 2.2µF, TA = +25°C, unless otherwise noted.
Typical Operating Characteristics (continued)
(VIN = 5V or VUSB = 5V, VBATT = 4V, R POK = RCHG = 200kΩ to 5V, EN = unconnected, RSETI = 2.8kΩ to GND, RMIN = 1.74kΩ to
GND, RDETBAT = 4.7kΩ to GND, CBATT = 2.2µF, TA = +25°C, unless otherwise noted.
FAST-CHARGE CURRENT
vs. RSETI
BATTERY REGULATION ACCURACY
vs. AMBIENT TEMPERATURE
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
10,000
MAX8844 toc13
IBATT = 0A
0.8
FAST-CHARGE CURRENT (mA)
MAX8844 toc12
1000
100
-0.8
10
-1.0
-40
-15
10
35
60
1
85
TOP-OFF THRESHOLD CURRENT
vs. 1/RMIN (kΩ)
CHARGE CURRENT
vs. AMBIENT TEMPERATURE
700
MAX8844 toc14
450
600
CHARGE CURRENT (mA)
400
TOP-OFF CURRENT RISING
300
250
200
150
100
RSETI (kΩ)
500
350
10
AMBIENT TEMPERATURE (°C)
TOP-OFF CURRENT FALLING
VBATT = 4V
500
400
300
VBATT = 3.2V
200
100
100
RSETI = 2.8kΩ
0
50
-40
0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0.5 0.7 0.9 1.1 1.3 1.5 1.7 1.9
1/RMIN (kΩ)
-20
0
20
40
100
MAX8844 toc17
5V/div
0
5V/div
VABI
0
5V/div
0
VIN
80
AUTOBOOT ENABLED
BY INPUT VOLTAGE (MAX8844Z)
MAX8844 toc16
VABI
60
AMBIENT TEMPERATURE (°C)
AUTOBOOT ENABLED BY ABI SIGNAL
(MAX8844Z)
5V/div
0
VIN
VBATT
5V/div
0
5V/div
VBATT
5V/div
0
5V/div
VABO
0
VABO
0
4μs/div
6
MAX8844 toc15
BATTERY REGULATION ACCURACY (%)
1.0
TOP-OFF THRESHOLD CURRENT (mA)
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
20μs/div
_______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
PIN
MAX8844Z
MAX8844Y
1
1
2
2
NAME
FUNCTION
IN
Input Supply Voltage. IN is the power supply for the SAFEOUT linear regulator and the
battery charger. See the DC and USB Power Supplies section. Bypass IN to GND with a
1µF or larger ceramic capacitor to improve line noise and input transient rejection.
POK
Active-Low, Input Voltage Status Indicator. POK is an open-drain output that asserts low
when 2.35V < (VIN or VUSB) < 7V and [(VIN or VUSB) - VBATT] > 40mV. If (VIN or VUSB) >
+7.5V or VBATT > (VIN or VUSB), the IC is shut down and POK becomes high impedance.
Connect a pullup resistor to the microprocessor’s I/O voltage when interfacing with a
microprocessor logic input.
3
3
USB
USB Input Supply Voltage. USB is the power supply for the SAFEUSB linear regulator
and the battery charger. See the DC and USB Power Supplies section. Bypass USB to
GND with a 1µF or larger ceramic capacitor to improve line noise and input transient
rejection.
4
4
ABI
Autobooting External Input. See the Autobooting Assistant section and Table 1 for
autobooting conditions. ABI is pulled to GND through an internal 200kΩ resistor.
5
—
ABO
Active-High, Autobooting Logic Output. See the Autobooting Assistant section and Table
1 for autobooting conditions.
—
5
ABO
Active-Low, Autobooting Logic Output. See the Autobooting Assistant section and Table
1 for autobooting conditions.
6
6
MIN
Top-Off Current Threshold Programmable Input. IMIN (mA) falling = 126V/RMIN (kΩ) + 27
(mA).
Charge-Current Program and Fast-Charge Current Monitor. Output current from SETI is
1120µA per ampere of battery charging current. Set the charging current by connecting
a resistor (RSETI in Figure 3) from SETI to GND. IFAST-CHARGE = 1250V/RSETI. To
configure the MAX8844Z/MAX8844Y as a USB charger, see Figure 5.
7
7
SETI
8
8
DETBAT
Battery Pack ID Resistor Detection Input. If DETBAT is pulled low through a pulldown
resistor less than 51kΩ, the charger is enabled. If DETBAT is left unconnected, the
charger is disabled.
9
9
CHG
Active-Low, Charging Indicator. CHG is an open-drain output that is pulled low once
charging begins. CHG is high impedance when the battery current drops below MIN, or
when the IC is disabled. Connect a pullup resistor to the microprocessor’s I/O voltage
when interfacing with a microprocessor logic input.
10
10
EN
Active-Low, Logic-Level Enable Input. Drive EN high to disable charger. Drive EN low or
leave unconnected for normal operation. EN has an internal 200kΩ pulldown resistor.
11
11
GND
Ground. Connect GND and the exposed pad to a large copper ground plane for
maximum power dissipation. Connect GND to the exposed pad directly under the IC.
12
12
BATT
Li+ Battery Connection. Bypass BATT to GND with a 2.2µF ceramic capacitor.
13
13
SAFEUSB
4.7V Regulated LDO Output with Input Overvoltage Protection. Bypass SAFEUSB to
GND with a 1µF or larger ceramic capacitor. SAFEUSB can be used to supply lowvoltage-rated USB systems.
_______________________________________________________________________________________
7
MAX8844Z/MAX8844Y
Pin Description
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
Pin Description (continued)
PIN
NAME
MAX8844Z
MAX8844Y
14
14
SAFEOUT
—
—
EP
FUNCTION
4.7V Regulated LDO Output with Input Overvoltage Protection. Bypass SAFEOUT to
GND with a 1µF or larger ceramic capacitor. SAFEOUT can be used to supply lowvoltage-rated charging systems.
Exposed Pad. Connect the exposed pad to a large ground plane for maximum power
dissipation. Connect GND to the exposed pad directly under the IC.
LINEAR
REGULATOR
WITH OVP
SAFEUSB
USB
LINEAR
REGULATOR
WITH OVP
SAFEOUT
BATT
IN
4.2V
Li+
+115°C
OUTPUT DRIVER,
CURRENT SENSE,
AND LOGIC
TEMPERATURE
SENSOR
DETBAT
SETI
VREF
VREF
VI/O
IMINREF
MIN
IN/USB*
CHG
VIN/VUSB*
OVLO
VL
REGULATOR
POK
BATT
BATT
POK
VL
VL
UVLO
REF
ABO (MAX8844Z ONLY)
LOGIC
DETBAT
VREF
ABI
REFOK
200kΩ
ABO (MAX8844Y ONLY)
EN
MAX8844Z
MAX8844Y
200kΩ
*SEE THE DC AND USB
POWER SUPPLIES SECTION.
GND
EP
Figure 1. Functional Diagram
8
_______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
The MAX8844Z/MAX8844Y chargers use voltage, current, and thermal-control loops to charge a single Li+
cell and protect the battery (Figure 1). When a Li+ battery with a cell voltage below 2.5V is inserted, the
MAX8844Z/MAX8844Y chargers enter a prequalification stage where they precharge that cell with 10% of
the user-programmed fast-charge current (Figure 2).
The CHG indicator is driven low to indicate entry into
the prequalification state. When the battery voltage
exceeds 2.5V, the charger soft-starts as it enters the
fast-charge stage. The fast-charge current level is programmed through a resistor from SETI to GND. As the
battery voltage approaches 4.2V, the battery current is
reduced. If the battery current drops to less than the
top-off current threshold set by R MIN , the charger
enters top-off mode and the CHG indicator goes high
impedance, signaling that the battery is fully charged.
Overvoltage Protected Output (SAFEUSB)
SAFEUSB is a linear regulator that provides an output
voltage of 4.7V and can be used to supply low voltage
rated USB systems. The SAFEUSB linear regulator
turns on when VUSB ≥ 4.25V regardless of EN and is
disabled when VUSB is greater than the overvoltage
threshold (7.5V typ).
Battery Pack Detection Input (DETBAT)
DETBAT is a battery pack ID resistor detector that
enables the battery charger if pulled low through a
resistor that is less than 51kΩ. If DETBAT is left unconnected or the pulldown resistor is 51kΩ or greater, the
battery charger is disabled.
POK Output
The open-drain POK output asserts low when 2.35V ≤
(VIN or VUSB) ≤ 7V, [(VIN or VUSB) - VBATT] ≥ 40mV
(typ V IN or V USB rising), and DETBET is pulled low
through a resistor that is less than 51kΩ. POK is high
Overvoltage-Protected Output (SAFEOUT)
SAFEOUT is a linear regulator that provides an output
voltage of 4.7V and can be used to supply low-voltagerated charging systems. The SAFEOUT linear regulator
ASYNCHRONOUS
FROM ANYWHERE
VIN* > 7.5V, OR
(VIN* - VBATT) < 30mV, OR
THERMAL SHUTDOWN, OR
IC DISABLED
SHUTDOWN
CHARGER = DISABLED
CHG = HIGH-Z
VBATT < 2.5V
(VIN* - VBATT) < 30mV
PRECHARGE
10% OF IFAST-CHARGE
CHG = LOW
VIN* < 7.5V, AND
(VIN* - VBATT) ≥ 40mV, AND
IC ENABLED
ANY CHARGING STATE
VBATT < 2.4V
VIN* > 7V, OR
(VIN* - VBATT) < 30mV, OR
IC DISABLED
DIE TEMPERATURE > +115°C
CHARGING CURRENT REDUCTION
CHARGING CURRENT IS REDUCED
AS NECESSARY
VBATT ≥ 2.5V
DIE TEMPERATURE ≤ +115°C
IBATT > 248V/RMIN (kΩ) - 16mA
FAST-CHARGE
CONSTANT-CURRENT CHARGE
100% OF IFAST-CHARGE
CHG = LOW
TOP-OFF
4.2 VOLTAGE REGULATION
CHG = HIGH-Z
RETURN TO
CHARGING STATE
IBATT ≤ IMIN
FOR 6.2ms (typ) OR LONGER
*SEE THE DC AND USB
POWER SUPPLIES SECTION.
Figure 2. Charge-State Diagram
_______________________________________________________________________________________
9
MAX8844Z/MAX8844Y
turns on when VIN ≥ 4.25V regardless of EN and is disabled when VIN is greater than the overvoltage threshold (7.5V typ).
Detailed Description
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
Table 1. Autobooting Output States
ABI
BATT
POK
CHARGER STATE
ABO
(MAX8844Z)
ABO
(MAX8844Y)
Low
Present
High-Z
Shutdown
Low
High-Z
High
Present
High-Z
Shutdown
High
Low
Low
Not present
Low
CC/CV mode
High
High-Z
Low
Present
Low
Fast-charge/top-off
High
High-Z
High
Present
Low
Fast-charge/top-off
High
Low
Note: Present indicates that VBATT ≥ 2.0V and Not Present indicates that the battery is not connected.
impedance during shutdown. When interfacing with a
microprocessor logic input, a pullup resistor to the
microprocessor’s I/O voltage may be required. If
DETBAT is not used, connect DETBAT to GND for normal operation.
4) is required for ESD protection and noise filtering. If
ABI is supplied by a system’s internal GPIO, or logic,
the RC filter is not required.
For the MAX8844Y, the output ABO is only dependent
on the state of ABI (Table 1).
Autobooting Assistant
The MAX8844Z/MAX8844Y contain an autobooting
assistant circuit that generates an enable signal for system booting (ABO, ABO). For the MAX8844Z, the booting assistant functions as an internal OR gate (Figure 1).
The first input is dependent on the input supply voltage
(VIN or VUSB) and DETBAT while the second input is an
external signal applied to ABI. The first input (POK) is driven high once DETBAT is pulled low through a resistor
less than 51kΩ, 2.35V ≤ (VIN or VUSB) ≤ 7V, and [(VIN or
VUSB) - VBATT] ≥ 40mV (typ VIN rising).
The second input signal (ABI) is driven by an external
source (Table 1). ABI enables an autoboot signal when
a battery is connected at BATT and is independent of
POK. If POK is pulled low, the booting assistant always
drives ABO high regardless of ABI. ABI is pulled to
GND through an internal 200kΩ resistor. If ABI is supplied from an outside exposed pin, an RC filter (Figure
CHG Charge Indicator Output
CHG is an open-drain output that indicates charge status. Table 2 describes the state of CHG during different
stages of operation. CHG is suitable for driving a
charge indication LED. If the MAX8844Z/MAX8844Y are
used in conjunction with a microprocessor, a pullup
resistor to the logic I/O voltage allows CHG to indicate
charge status to the microprocessor instead of driving
an LED.
Thermal Regulation
The thermal-regulation loop limits the MAX8844Z/
MAX8844Y die temperatures to +115°C by reducing the
charge current as necessary. This feature not only protects the IC from overheating, but also allows a higher
charge current without risking damage to the system.
Table 2. CHG States
EN
High
VIN*
VBATT
IBATT
CHG
STATE
0
High-Z
Disabled
0
High-Z
Shutdown
Low
Precharge
X
X
> 7.5V
X
X
> VIN* - 30mV
Low
4.25V ≤ VIN* ≤ 7.5V
< 2.4V
10% of
IFAST-CHARGE†
Low
4.25V ≤ VIN* ≤ 7.5V
≥ 2.5V
100% of IFAST-CHARGE†
Low
Fast-charge
Low
4.25V ≤ VIN* ≤ 7.5V
4.2V
< IMIN
High-Z
Top-off
Low
X = Don’t care.
*VIN and VUSB are interchangeable. See the DC and USB Power Supplies section.
†I
FAST-CHARGE is reduced as necessary to prevent the die temperature from exceeding +115°C.
10
______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
Top-Off Current Threshold Setting
The top-off current threshold is programmed by an
external resistor connected from MIN to GND (RMIN).
Use the following equation to determine the top-off current (IMIN):
IMIN (falling) = 126V/RMIN (kΩ) + 27mA
Soft-Start
The soft-start algorithm activates when entering fastcharge mode. When the prequalification state is complete (V BATT exceeds +2.5V), the charging current
ramps up in 250µs to the full charging current. This
reduces the inrush current demand on the input supply.
Applications Information
Fast-Charge Current Setting
The maximum charging current is programmed by an
external resistor connected from SETI to GND (RSETI).
Use the following equation to determine the fast-charge
current (IFAST-CHARGE):
IFAST-CHARGE =
1250V
RSETI
where IFAST-CHARGE is in amps and RSETI is in ohms.
RSETI must always be 1.25kΩ or higher due to the continuous charging current limit of 1ARMS.
IMIN (rising) = 248V/RMIN (kΩ) - 16mA
where IMIN is in mA and RMIN is in kΩ. Use RMIN ≤
2.2kΩ.
Capacitor Selection
Connect a ceramic capacitor from BATT to GND for
proper stability. Use a 2.2µF ceramic capacitor for most
applications. Connect 1µF ceramic capacitors from IN
to GND and from USB to GND. A larger input capacitor
can be used for high charging current to reduce input
voltage ripple.
Connect 1µF ceramic capacitors from SAFEOUT to
GND and from SAFEUSB to GND. A larger bypass
capacitor for SAFEOUT and SAFEUSB can be used for
optimum noise immunity. Ceramic capacitors with X5R
or X7R dielectric are highly recommended due to their
small size, low ESR, and small temperature coefficients.
Thermal Considerations
The MAX8844Z/MAX8844Y are available in a thermally
enhanced TDFN package with an exposed pad.
Connect the exposed pad to a large copper ground
plane to provide a thermal contact between the device
and the circuit board for increased power dissipation.
The exposed pad transfers heat away from the device,
allowing the IC to charge the battery with maximum current, while minimizing the increase in die temperature.
Table 3. Input Power-Supply Selection
IN
USB
CHARGER STATE
4.25V ≤ VIN ≤ 7V
4.25V ≤ VUSB ≤ 7V
4.25V ≤ VIN ≤ 7V
Not present
Not present
4.25V ≤ VUSB ≤ 7V
VIN ≥ 7.5V
4.25V ≤ VUSB ≤ 7V
Disabled
4.25V ≤ VIN ≤ 7V
VUSB ≥ 7.5V
Enabled
Enabled, selects IN power supply
Enabled, selects IN power supply
Enabled, selects USB power supply
______________________________________________________________________________________
11
MAX8844Z/MAX8844Y
Charger Enable Input
The MAX8844Z/MAX8844Y contain an active-low logic
input (EN) used to enable the chargers. Drive EN low,
leave unconnected, or connect to GND to enable the
charge-control circuitry. Drive EN high to disable the
charger-control circuitry. EN has an internal 200kΩ pulldown resistor.
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
4.2V Li+
USB
BATT
CUSB
1μF
AC ADAPTER
IN
GND
SYSTEM
CBATT
2.2μF
MAX8844Z
CIN
1μF
DETBAT
SAFEUSB
VBUS
CSAFEUSB
1μF
ABI
SAFEOUT
CSAFEOUT
1μF
VCHG
VI/O
RCHG
1MΩ
RPOK
1MΩ
SETI
RSETI
2.8kΩ
MIN
GPIO
CHG
ABO
GND
EP
POK
GPIO
EN
GPIO
RMIN
1.75kΩ
POWER
SUPPLY
IF THE POWER SUPPLY
IS ACTIVE-LOW ENABLED,
USE THE MAX8844Y.
ON
Figure 3. AC Adapter Application
DC and USB Power Supplies
Typical Application Circuits
The MAX8844Z/MAX8844Y operate from well-regulated
DC sources and automatically select between both
input power supply connections (Table 3). If both
sources are present at the same time, highest priority is
given to the IN source. The IN source is selected to
ensure the shortest charging time for the system since
it is able to deliver the highest current. The USB fastcharge current is fixed at 380mA (MAX8844Z) and
450mA (MAX8844Y).
The full charging input voltage range for IN and USB is
4.25V to 7.5V. The device can withstand up to 28V on
both inputs, IN and USB, without damage to the IC. If
VIN or VUSB is greater than 7.5V, the internal overvoltage-protection circuitry disables charging until the
input falls below 7.5V. The power supplies must provide
at least 4.25V at the desired peak charging current and
stay below 7V when unloaded.
AC Adapter Application
Figure 3 shows the MAX8844Z as a Li+ battery charger
with an AC adapter. The MAX8844Z detects the presence of an input supply and DETBET resulting in POK
pulled low. Once POK is pulled low, the autobooting
assistant drives ABO high and enables the power supplies of the system to boot up. The MAX8844Z begins
charging the battery when EN is low or unconnected.
By monitoring CHG, the system can detect the top-off
threshold and terminate the charge through EN. The
MAX8844Z also provides an overvoltage-protected
SAFEOUT and SAFEUSB to the system.
12
Factory System Interface Connector Application
Figure 4 shows the MAX8844Z as an autoboot assistant
with the factory system interface connector. The
MAX8844Z detects the ABI input even though there is
no input voltage available and drives ABO high to turn
______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
CBATT
2.2μF
SYSTEM
MAX8844Z
IN
4.2V
INTERFACE
CONNECTOR
GND
MAX8844Z/MAX8844Y
BATT
USB
CUSB
1μF
DETBAT
CIN
RABI 1μF
10kΩ
VBUS
SAFEUSB
CSAFEUSB
1μF
ABI
CABI
1μF
VCHG
SAFEOUT
CSAFEOUT
1μF
VI/O
RCHG
1MΩ
RPOK
1MΩ
SETI
RSETI
2.8kΩ
MIN
GPIO
CHG
ABO
GND
EP
POK
GPIO
EN
GPIO
RMIN
1.75kΩ
POWER
SUPPLY
IF THE POWER SUPPLY
IS ACTIVE-LOW ENABLED,
USE THE MAX8844Y.
ON
Figure 4. Factory System Interface Connector Application
on power supplies to boot up the system. The configuration in Figure 4 is used for system development, testing, and calibrations in production or design stage.
USB-Powered Li+ Charger
The universal serial bus (USB) provides a high-speed
serial communication port as well as power for the
remote device. The MAX8844Z can be configured to
charge a battery at the highest current possible from
the host port. Figure 5 shows the MAX8844Z as a USB
battery charger with the default charging current as
380mA. The MAX8844Z also provides an overvoltage
protected SAFEUSB to the system.
USB Connector and AC Adapter
Figure 6 shows the MAX8844Z as a Li+ battery charger
with an AC adapter and USB connector. The
MAX8844Z detects the presence of input supplies and
DETBET resulting in POK pulled low. Once POK is
pulled low, the autobooting assistant drives ABO high
and enables the power supplies of the system to boot
up. The MAX8844Z begins charging the battery from IN
source when EN is low or open. By monitoring CHG,
the system can detect the top-off threshold and terminate the charge through the EN pin. The MAX8844Z
provides overvoltage protected SAFEOUT and
SAFEUSB to the system.
Figure 7 shows the timing diagram.
Recommended PCB Layout and Routing
Place all bypass capacitors for IN, USB, BATT, SAFEOUT,
and SAFEUSB as close to the device as possible.
Connect the battery to BATT as close as possible to the
device to provide accurate battery voltage sensing.
Provide a large copper ground plane to allow the
exposed pad to sink heat away from the device. Make all
high-current traces short and wide to minimize voltage
drops. A sample layout is available in the MAX8844Z evaluation kit to speed designs.
______________________________________________________________________________________
13
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
4.2V Li+
BATT
USB
USB
CABLE
GND
CBATT
2.2μF
CUSB
1μF
SYSTEM
MAX8844Z
IN
DETBAT
SAFEOUT
SAFEUSB
CIN
1μF
VBUS
CSAFEOUT
1μF
ABI
RCHG
1MΩ
GPIO
CHG
ABO
RPOK
1MΩ
SETI
RSETI
2.8kΩ
MIN
VI/O
GND
EP
POK
GPIO
EN
GPIO
RMIN
1.75kΩ
POWER
SUPPLY
ON
IF THE POWER SUPPLY
IS ACTIVE-LOW ENABLED,
USE THE MAX8844Y.
Figure 5. USB Battery Charger
14
______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
MAX8844Z/MAX8844Y
4.2V Li+
BATT
USB
CABLE
GND
CBATT
2.2μF
USB
CUSB
1μF
MAX8844Z
SYSTEM
DETBAT
VBUS
SAFEUSB
AC
ADAPTER
GND
CSAFEUSB
1μF
IN
CIN
1μF
SAFEOUT
VCHG
CSAFEOUT
1μF
VI/O
ABI
RCHG
1MΩ
RPOK
1MΩ
SETI
RSETI
2.8kΩ
MIN
GPIO
CHG
ABO
GND
EP
POK
GPIO
EN
GPIO
RMIN
1.75kΩ
POWER
SUPPLY
IF THE POWER SUPPLY
IS ACTIVE-LOW ENABLED,
USE THE MAX8844Y.
ON
Figure 6. USB Connector and AC Adapter Application
______________________________________________________________________________________
15
MAX8844Z/MAX8844Y
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
OVP
OVP
POK
VIN
OVP
OVP
POK
VUSB
VPOK
VEN
VCHG
VSAFEOUT = 4.7V
VSAFEOUT
VSAFEUSB = 4.7V
VSAFEUSB
TIME
Figure 7. Timing Diagram
16
______________________________________________________________________________________
28V Dual Input Linear Li+ Battery Chargers with
Battery Detection and Overvoltage-Protected Output
DETBAT
4.25V TO 28V
IN
BATT
CIN
1μF
CBATT
2.2μF
4.2V
Li+
MAX8844Z
MAX8844Y
4.25V TO 28V
USB
SYSTEM
SUPPLY
CUSB
1μF
ABI
OFF
ON
EN
MIN
CHG
RMIN
1.75kΩ
POK
(MAX8844Y, ABO)
(MAX8844Z, ABO)
SETI
SAFEOUT
RSETI
2.80kΩ
CSAFEOUT
1μF
SAFEUSB
GND
EP
CSAFEUSB
1μF
Chip Information
Pin Configuration
SAFEUSB
BATT
GND
EN
CHG
DETBAT
TOP VIEW
SAFEOUT
PROCESS: BiCMOS
14
13
12
11
10
9
8
Package Information
For the latest package outline information and land patterns, go
to www.maxim-ic.com/packages.
*EXPOSED PAD
1
2
3
4
5
6
7
MIN
+
SETI
21-0137
ABO/ABO*
T1433-2
ABI
14 TDFN-EP
(3mm x 3mm)
MAX8844Z
MAX8844Y
USB
DOCUMENT NO.
IN
PACKAGE CODE
POK
PACKAGE TYPE
TDFN
* = ABO—MAX8844Z, ABO—MAX8844Y
Maxim cannot assume responsibility for use of any circuitry other than circuitry entirely embodied in a Maxim product. No circuit patent licenses are
implied. Maxim reserves the right to change the circuitry and specifications without notice at any time.
Maxim Integrated Products, 120 San Gabriel Drive, Sunnyvale, CA 94086 408-737-7600 ____________________ 17
© 2009 Maxim Integrated Products
Maxim is a registered trademark of Maxim Integrated Products, Inc.
MAX8844Z/MAX8844Y
Typical Operating Circuit