SCOPE: CMOS, TTL-COMPATIBLE ANALOG SWITCHES Device Type 01 02 03 04 Generic Number DG304AA(x)/883B DG305AA(x)/883B DG306AA(x)/883B DG307AA(x)/883B Case Outline(s). The case outlines shall be designated in Mil-Std-1835 and as follows: Outline Letter A K Z Mil-Std-1835 MACY1-X10 GDIP1-T14 or CDIP2-T14 CQCC1-N20 Case Outline Package Code 10 Pin TO-100 A10 14 LEAD CERDIP J14 20-Pin Ceramic LCC L20 Absolute Maximum Ratings V+ to V- ............................................................................................................................. 44V V+ to GND ........................................................................................................................ 25V Digital Input Overage Range ........................................................................... -2V to (V+ +2V) Current, Any terminal except S or D ............................................................................... 30mA Continuous Current, S or D ............................................................................................. 30mA Peak Current (pulsed at 1ms, 10% duty cycle max) ...................................................... 100mA Lead Temperature (soldering, 10 seconds) ........................................................................ +300°C Storage Temperature ........................................................................................... -65°C to +150°C Continuous Power Dissipation ............................................................................ TA=+70°C 10 lead Can (derate 6.7mW/°C above +70°C) ......................................................... 533mW 14 lead CERDIP(derate 9.1mW/°C above +70°C) .................................................. 727mW 20-Pin LCC (derate 9.1mW/°C above +70°C) ........................................................ 727mW Junction Temperature TJ ............................................................................…....... +150°C Thermal Resistance, Junction to Case, ΘJC: Case Outline TO-100 Can ....................................................................... 45°C/W Case Outline 14 lead CERDIP................................................................. 55°C/W Case Outline 20-Pin LCC ....................................................................... 20°C/W Thermal Resistance, Junction to Ambient, ΘJA: Case Outline TO-100 Can .................................................................... 150°C/W Case Outline 14 lead CERDIP.............................................................. 110°C/W Case Outline 20-Pin LCC .................................................................... 110°C/W Recommended Operating Conditions. Ambient Operating Range (TA) ........................................................... -55°C to +125°C NOTE 1: Signals on SX, DX, or INX exceeding V+ or V- are clamped by internal diodes, and are also internally current limited to 25mA. Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. These are stress ratings only, and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of the specifications is not implied. Exposure to absolute maximum rating conditions for extended periods may affect device reliability. ---------------------------- Electrical Characteristics of DG304A/DG305/ DG306/DG307/883B 19-0058 Page 2 of Rev. B 6 TABLE 1. ELECTRICAL TESTS TEST SWITCH Analog-Signal Range Drain-Source ON Resistance Drain-Source ON Resistance Source OFF Leakage Current Symbol CONDITIONS -55 °C <=TA<= +125°C V+=+15V, V-=-15V, GND=0V VINH=11.0V, VINL=3.5V Unless otherwise specified Limits Min Limits Max -15 15 All IS =-10mA, VD=10V, VIN=3.5V or VIN=11V IS =10mA, VD=-10V, VIN=3.5V or VIN=11V VS =14V, VD=-14V, VIN=3.5V or VIN=11V 1,3 2 1,3 2 1 2 All All -1 -100 50 75 50 75 1 100 VS=±15V rDS(ON) IS(OFF) Device type 1,2,3 VANALOG rDS(ON) Group A Subgroup All Units V Ω Ω nA Source OFF Leakage Current IS(OFF) VS =-14V, VD=14V, VIN=3.5V or VIN=11V 1 2 All -1 -100 1 100 nA Drain OFF Leakage Current ID(OFF) VS =14V, VD=-14V, VIN=3.5V or VIN=11V 1 2 All -1 -100 1 100 nA Drain OFF Leakage Current ID(OFF) VS =-14V, VD=14V, VIN=3.5V or VIN=11V 1 2 All -1 -100 1 100 nA Drain ON Leakage Current ID(ON) VD=VS=14V, VIN=3.5V or 11V 1 2 All -2 -200 2 200 nA Drain ON Leakage Current ID(ON) VD=VS=-14V, VIN=3.5V or 11V 1 2 All -2 -200 2 200 nA 1,2,3 All INPUT Input Current/Voltage High Input Current/Voltage Low SUPPLY Positive Supply Current VIN= 5.0V IINH -1 µA VIN=15V 1 1,2,3 All VIN=15V, one input; all others =0V 1,3 2 All VIN=0V, all inputs 1.3 2 1,3 2 IINL VIN=0V I+ µA -1 10 100 mA Negative Supply Current I- VIN=15V, one input; all others =0V 10 100 All All -10 -100 µA VIN=0V, all inputs DYNAMIC Turn ON time tON Figure 1 Turn OFF time tOFF Figure 1 ---------------------------- 1,3 2 9 10,11 9 10,11 Electrical Characteristics of DG304A/DG305/ DG306/DG307/883B All -10 -100 All 250 450 150 350 All 19-0058 Page 3 of Rev. B 6 ns ns FIGURE 1: SWITCHING TIME TEST CIRCUIT: See Commercial Data Sheet TRUTH TABLE Device Type 01/03 01/03 02 02 02 02 04 04 04 04 Logic 0 1 0 1 0 1 0 0 1 1 Switch OFF ON OFF ON ON OFF OFF ON ON OFF ORDERING 01 01 02 02 03 04 04 Information DG304AAA DG304AAK DG305AAA DG305AAK DG306AAK DG307AAK DG307AAZ /883B /883B /883B /883B /883B /883B /883B ---------------------------- Switch 1 Switch 1 Switch 2 Switch 2 Switch 1,2 Switch 3,4 Switch 1,2 Switch 3,4 TERMINAL CONNECTION TERMINAL 01 02 03 NUMBER J14 J14 J14 1 NC NC NC 2 D1 D2 S3 3 NC NC D3 4 S1 S1 D1 5 NC NC S1 6 IN1 IN IN1 7 GND GND GND 8 VVV9 IN2 NC IN2 10 NC NC S2 11 S2 S2 D2 12 NC NC D4 13 D2 D2 S4 14 V+ V+ V+ TO-100 1 D1 D1 2 S1 S1 3 IN1 IN 4 NC NC 5 GND GND 6 VV7 IN2 NC 8 S2 S2 9 D2 D2 10 V+ V+ Electrical Characteristics of DG304A/DG305/ DG306/DG307/883B 04 J14 NC S3 D3 D1 S1 IN1 GND VIN2 S2 D2 D4 S4 V+ 19-0058 Page 4 of Rev. B 6 QUALITY ASSURANCE Sampling and inspection procedures shall be in accordance with MIL-Prf-38535, Appendix A as specified in MilStd-883. Screening shall be in accordance with Method 5004 of Mil-Std-883. Burn-in test Method 1015: 1. Test Condition, A, B, C, or D. 2. TA = +125°C minimum. 3. Interim and final electrical test requirements shall be specified in Table 2. Quality conformance inspection shall be in accordance with Method 5005 of Mil-Std-883, including Groups A, B, C, and D inspection. Group A inspection: 1. Tests as specified in Table 2. 2. Selected subgroups in Table 1, Method 5005 of Mil-Std-883 shall be omitted. Group C and D inspections: a. End-point electrical parameters shall be specified in Table 1. b. Steady-state life test, Method 1005 of Mil-Std-883: 1. Test condition A, B, C, D. 2. TA = +125°C, minimum. 3. Test duration, 1000 hours, except as permitted by Method 1005 of Mil-Std-883. TABLE 2. ELECTRICAL TEST REQUIREMENTS Mil-Std-883 Test Requirements Interim Electric Parameters Method 5004 Final Electrical Parameters Method 5005 Group A Test Requirements Method 5005 Group C and D End-Point Electrical Parameters Method 5005 * ** Subgroups per Method 5005, Table 1 1 1*, 2, 3, 9 1, 2, 3, 9, 10**, 11** 1 PDA applies to Subgroup 1 only. Subgroups 10 and 11, if not tested shall be guaranteed to the limits of Table 1. ---------------------------- Electrical Characteristics of DG304A/DG305/ DG306/DG307/883B 19-0058 Page 5 of Rev. B 6