EPCOS B32227J6103M000

Film Capacitors
Metallized Polyester Film Capacitors (MKT)
Series/Type:
Date:
B32227
August 2004
© EPCOS AG 2004. Reproduction, publication and dissemination of this data sheet, enclosures hereto and the
information contained therein without EPCOS' prior express consent is prohibited.
Purchase orders are subject to the General Conditions for the Supply of Products and Services of the Electrical
and Electronics Industry recommended by the ZVEI (German Electrical and Electronic Manufacturers' Association), unless otherwise agreed.
Metallized polyester film capacitors (MKT)
B32227
High voltage (wound)
Typical applications
Test and measurement equipment
Laser, ultrasonic, X-ray, microwave
Dimensional drawing
Climatic
Max. operating temperature: 85 °C
Climatic category (IEC 60068-1): 40/085/21
Construction
Dielectric: polyethylene terephthalate
(polyester, PET)
Flat winding
Insulating sleeve
Face ends sealed with epoxy resin
Dimensions in mm
Width wmax
Lead diameter d1
≤6.0
0.6
8 ... 10
0.8
≥10.5
1.0
When bending leads take care to leave a
clearance of 1 mm to the capacitor body.
Terminals
Central axial wire leads, lead-free tinned
Marking
Manufacturer's logo,
style (MKT), series number, rated capacitance,
capacitance tolerance (code letter),
rated DC voltage, date of manufacture (coded)
Delivery mode
Bulk (untaped)
2
B32227
High voltage (wound)
Overview of available types
Type
B32227
Page
4
VR (VDC)
1000
1600
2500
4000
6300
Vrms (VAC)
220
220
220
220
220
CR (µF)
0.010
0.025
0.05
0.10
0.25
3
B32227
High voltage (wound)
Ordering codes and packing units
VR
Vrms
CR
f ≤60 Hz
VDC VAC
µF
0.050
1000 220
0.10
0.25
0.025
1600 220
0.050
0.10
0.25
0.025
2500 220
0.050
0.10
0.25
0.010
4000 220
0.025
0.050
0.10
0.010
6300 220
0.025
0.050
Max. dimensions
w×h×l
mm
5.5 × 12.0 × 33.0
6.0 × 18.5 × 33.0
9.5 × 25.0 × 33.0
5.0 × 11.5 × 33.0
6.0 × 16.5 × 33.0
8.0 × 20.0 × 33.0
15.5 × 31.0 × 33.0
8.5 × 18.0 × 33.0
12.5 × 25.5 × 33.0
10.5 × 26.5 × 45.0
15.5 × 40.5 × 45.0
9.5 × 22.0 × 33.0
10.0 × 22.5 × 45.0
12.5 × 31.0 × 45.0
16.5 × 42.0 × 45.0
9.0 × 21.5 × 45.0
13.5 × 32.5 × 45.0
17.0 × 42.0 × 45.0
Ordering code
(composition see
below)
B32227J0503M000
B32227J0104M000
B32227J0254M000
B32227J1253M000
B32227J1503M000
B32227J1104M000
B32227J1254M000
B32227J2253M000
B32227J2503M000
B32227J2104M000
B32227J2254M000
B32227J4103M000
B32227J4253M000
B32227J4503M000
B32227J4104M000
B32227J6103M000
B32227J6253M000
B32227J6503M000
Further E series and intermediate capacitance values on request.
Composition of ordering code
Capacitance tolerance code: M = ±20%
4
Untaped
pcs./unit
100
50
20
100
100
50
20
50
50
20
20
20
20
20
20
20
20
20
B32227
High voltage (wound)
Technical data
Operating temperature range
Max. operating temperature Top,max
Upper category temperature Tmax
Lower category temperature Tmin
Rated temperature TR
Dissipation factor tan δ (in 10-3) at 1 kHz: 8
at 20 °C
at 10 kHz: 15
(upper limit values)
Insulation resistance Rins
30 000 MΩ
at 20 °C, rel. humidity ≤ 65%
(minimum as-delivered values)
DC test voltage
1.2 VR, 2 s
TA (°C)
DC voltage derating
Category voltage VC
(continuous operation with VDC TA ≤ 70
VC = VR
or VAC at f ≤ 60 Hz)
70 <TA ≤85 VC = VR 0.55
Damp heat test
21 days/40 °C/93% relative humidity
Limit values after damp
Capacitance change ∆C/C
heat test
Dissipation factor change ∆ tan δ
Insulation resistance Rins
Reliability:
Failure rate λ
Service life tSL
Failure criteria:
Total failure
Failure due to variation
of parameters
+85 °C
+85 °C
40 °C
+85 °C
AC voltage derating
VC,rms = Vrms
VC,rms = Vrms 0.70
≤ 3%
(for C R > 0.1 µF)
≤ 5%
(for C R ≤ 0.1 µF)
≤ 3 10-3 (at 1 kHz)
≤ 5 10-3 (at 10 kHz)
≥ 20% of minimum
as-delivered values
10 fit (≤ 10 10-9 /h) at 0.5 VR, 40 °C
200 000 h at 1.0 VR, 40 °C
For conversion to other operating conditions and temperatures,
refer to chapter "Quality assurance", page .
Short circuit or open circuit
Capacitance change ∆C/C
Dissipation factor tan δ
Insulation resistance Rins
5
> 10%
> 2 upper limit value
< 150 MΩ
B32227
High voltage (wound)
Pulse handling capability
"dV/dt" represents the maximum permissible voltage change per unit of time for non-sinusoidal
voltages, expressed in V/µs.
"k0" represents the maximum permissible pulse characteristic of the waveform applied to the
capacitor, expressed in V 2/µs.
Note:
The values of dV/dt and k0 provided below must not be exceeded in order to avoid damaging the
capacitor.
dV/dt values
Lenght of capacitor
VR
Vrms
VDC
VAC
33 mm
1000
1600
2500
4000
6300
10
15
25
40
12.5
33 mm
45 mm
k0 in V2/µs
20 000
48 000
125 000
320 000
62 500
160 000
500 000
220
220
220
220
220
45 mm
dV/dt in V/µs
20
40
k0 values
Lenght of capacitor
VR
Vrms
VDC
VAC
1000
1600
2500
4000
6300
220
220
220
220
220
6
B32227
High voltage (wound)
Impedance Z versus frequency f
(typical values)
Permissible AC voltage Vrms versus frequency f
Values can be obtained on request. In specific cases please provide a scaled voltage/ time graph
and state operating conditions.
7