W E N Radiometrix Hartcran House, 231 Kenton Lane, Harrow, HA3 8RP, England 24 April 2007 BiM3B Tel: +44 (0) 20 8909 9595, Fax: +44 (0) 20 8909 2233 869MHz Wide Band FM radio transceiver The BiM3B radio transceiver module is an enhanced high power replacement for the European version BiM3B-869-64. Two frequency variants are available in the European unlicensed band, one with 5mW RF power with no duty cycle restriction other with 25mW RF power with 1% duty cycle restriction. Features Fig. 1: BiM3B-869.85-64 Complies with European harmonised standards EN 300 220 and EN 301 489 869.85MHz 5mW 100% duty cycle or 868.30MHz 25mW 1% duty cycle RF power output +14dBm (25mW) on 868.30MHz +7dBm (5mW) on 869.85MHz Data rates up to 64kbps Crystal controlled PLL FM circuitry for both Tx and Rx SAW front end filter and full screening Receiver Sensitivity: -101dBm for 1ppm BER (64kbps) -104dBm for 1ppm BER (10kbps) Supply: 2.9V - 16V @ 35mA Tx (25mW), 17mA TX (5mW), 11mA Rx Usable range up to 300 metres external, 75 metres in building SAW front end filter and full screening RSSI (standard) or carrier detect option Analogue and digital baseband Low profile with small footprint 33 x 23 x 5mm Applications PDAs, organisers and laptops Handheld terminals EPOS equipment, barcode scanners, belt clip printers Data loggers Audience response systems In-building environmental monitoring and control Security and fire alarms Restaurant ordering systems Vehicle data up/download Radiometrix Ltd, BiM3B Data Sheet page 1 Functional overview The transmit section of the BiM3B consists of a frequency modulated crystal locked PLL feeding a buffer amplifier and RF filter. A Tx select line controls operation. The transmitter achieves full RF output typically within 1ms of this line being pulled low. Modulation is applied at the TXD input and may be either a serial digital stream toggling between 0V and 3V (digital drive) or a high level analogue waveform with the same peak limits (linear drive). Modulation shaping is performed internally by a 2nd order lowpass filter, which minimises spectral spreading. The RF output is filtered to ensure compliance with the appropriate regulations and fed via a Tx/Rx changeover switch to the antenna pin. The receive section is a single conversion FM superhet with an IF of 10.7MHz. A SAW bandpass filter in the receiver front-end provides image rejection and suppression of other unwanted out-of-band signals. Like the transmitter, the receiver is controlled by its own active low RX select line. A post-detection lowpass filter establishes the signal bandwidth and ensures clean operation of the subsequent adaptive data slicer. The slicer is optimised for balanced data such as bi-phase code. The standard module features a received signal strength (RSSI) output with 60dB of range. A version of BiM3B featuring a fast acting Carrier Detect (CD) output on the same RSSI pin is also available. The CD output will indicate the presence of any RF signals on the carrier frequency. matching & lpf PA VCO ÷ 64 φ Loop Filter Antenna ÷ 32 Tx/Rx switch VCO φ ref osc 35kHz LPF ref osc TXD Vcc 2.9 - 16V Regulator & Tx/Rx logic Tx select Rx select Loop Filter RSSI/CD preamp 869MHz BPF IF Amp Demod Mixer LPF data slicer RXD 10.7MHz AF Pin description Fig. 2: Block diagram RF GND pins 1 & 3 RF ground pins, internally connected to the module screen and to pins 5, 9, 10 & 18 (0V). These pins should be connected directly to the RF return path (e.g. coax braid, main PCB ground plane etc). Antenna pin 2 50Ω RF connection to the antenna, DC-isolated. See pages 7 & 8 for details of suitable antennas and feeds. 0V (GND) pins 5, 9, 10 & 18 Supply ground connection and screen. RSSI pin 11 Received Signal Strength Indicator with 60dB range, operational when Rx is enabled. Output voltage nominally 0.15 - 0.40Vdc (no signal), 1.40Vdc (maximum). See page.6 for typical characteristics. CD pin 11 Carrier Detect - When the receiver is enabled, a low indicates a signal above the detection threshold is being received. The output is high impedance (50kΩ) and should only be used to drive a CMOS logic input. Radiometrix Ltd, BiM3B Data Sheet page 2 RXD pin 12 Digital output from internal data slicer. The output is a squared version of the signal on pin 13 (AF) and may be used to drive a decoder directly. The data is true data, i.e. as fed to the transmitter. Output is “open-collector” format with internal 10kΩ pullup to Vcc (pin 17). AF pin 13 Buffered & filtered analogue output from FM demodulator. Standing DC bias of 1V approx. Useful for test purposes or for driving external decoders. External load should be >10kΩ // <100pF TXD pin 14 This DC-coupled transmitter modulation input will accept either serial digital data or high level linear signals. Drive signal must be limited to 0V min, 3V max. See page 6 for suggested drive methods. Input impedance >50kΩ. TX select pin 15 Active-low Transmit select. 47kΩ internal pull-up to Vcc. RX select pin 16 Active-low Receive select. 47kΩ internal pull-up to Vcc. Pin 15 TX Pin 16 RX Function 1 1 1 0 Power down (<10µA) Receiver enabled 0 1 Transmitter enabled 0 0 Self test loop-back* * Loop-back allows the receiver to monitor the transmitted signal. Under these conditions the Tx radiated signal level will be reduced to approximately -10dBm). Vcc pin 17 DC +ve supply pin. +2.9 to +16.0 volts @ <17mA (@ 5mW). The supply should be clean, <20mVP-P ripple. side view (through can) side view (with can) 5 mm top view (without can) RF GND 1 Antenna 2 RF GND 3 4 5 No pin 6 7 8 0V 9 18 0V 17 Vcc 16 RX SELECT 15 TX SELECT 14 TXD 13 AF 12 RXD 11 RSSI/CD 10 0V 30.48 mm 33 mm 23 mm recommended PCB hole size: 1.2 mm module footprint size: 25 x 32 mm pin pitch: 2.54 mm (0.1") pins 4, 5, 6, 7 & 8 are not fitted Fig. 3: Physical dimensions Radiometrix Ltd, BiM3B Data Sheet page 3 Absolute maximum ratings Exceeding the values below may cause permanent damage to the module. Operating temperature Storage temperature -20°C to +70°C -40°C to +100°C Vcc (pin 17) TX, RX select (pins 15, 16) All other pins Antenna (pin 2) -0.3V to +16V -9V to +16V -0.3V to +Vcc ±50V DC, +10dBm RF Performance specifications Figures apply to standard version @ Vcc=3.0V, temperature +20°C, unless stated. General Supply voltage Tx supply current Tx supply current Rx supply current RF centre frequency RF centre frequency Antenna port impedance TX & RX select: high (deselect) low (select) Internal select pull-ups Balanced code bit rate Balanced code bit rate Transmitter section RF power output @ 869.85MHz RF power output @ 868.30MHz TX harmonics/spurious emission Initial centre frequency accuracy FM deviation Modulation bandwidth Modulation distortion TX spectral bandwidth @-40dBc TXD input level: high low TX power up to full RF Receiver section RF sensitivity, 10dB S/N RF sensitivity, 1ppm BER RF sensitivity, 10dB S/N RF sensitivity, 1ppm BER RSSI output, no signal RSSI output, max indication RSSI range IF bandwidth Image rejection (fRF-21.4MHz) IF rejection (10.7MHz) Local osc. leakage, conducted Baseband bandwidth @ -3dB Baseband bandwidth @ -3dB AF output signal level Radiometrix Ltd, BiM3B Data Sheet pin 17 17 17 17 2 15, 16 15, 16 15,16 12 12 min. 2.9 10 Vcc-0.5 0 - typ. 3.0 14 32 11 869.85 868.30 50 47 - max. 16 17 Vcc 0.5 64 10 units V mA mA mA MHz MHz Ω V V kΩ kbps kbps pin 2 2 2 2 14 14 2 pin 2, 13 2, 12 2, 13 2, 12 11 11 2, 11 2 2 2 13 13 13 notes min. -10 ±20 0 2.8 0 - typ. +7 +14 -55 0 ±27 5 1 max. -40 +10 ±35 35 10 250 3.0 0.2 1.5 units dBm dBm dBm kHz kHz kHz % kHz V V ms notes 100% duty cycle 1% duty cycle min. 0.15 40 100 0 0 200 typ. -106 -100 -113 -107 0.25 1.15 60 180 50 -117 300 max. 0.4 1.40 -110 50 7.8 400 units dBm dBm dBm dBm V V dB kHz dB dB dBm kHz kHz mV p-p notes -64 version -64 version -10 version -10 version Note 1 5mW version 25mW version Tx or Rx To Vcc (pin 17) -64 version -10 version Peak @ -3db Note 2 worst case Note 3 Note 3 Note 4 -50dBm RF input -64 version -10 version Note 5 page 4 Receiver section DC offset on AF output Distortion on recovered AF Ultimate (S+N)/N Load capacitance, AF & RXD pin 13 13 13 12, 13 min. 0.3 - typ. 1.0 1 40 - max. 1.75 10 100 units V % dB pF Dynamic Timing Rx power up with signal present Power up to valid RSSI, tPU-RSSI Power up to valid CD, tPU-CD Power up to stable data, tPU-data Power up to stable data, tPU-data 11 11 12 12 - 1 1.5 5 10 10 30 ms ms ms ms -64 version -10 version Signal applied with Rx on RSSI response time (rise/fall) Signal to stable data, tsig-data Signal to stable data, tsig-data 11 12 12 - 100 5 5 10 30 µs ms ms -64 version -10 version Time between data transitions Time between data transitions Averaged code mark:space 14 14 14 15.6 0.1 20 50 1500 15 80 µs ms % -64 version -10 version Note 8 Note: notes Note 6 Note 7 -50dBm RF input 1. Increases at high RF input level (>-20dBm) 2. See page 6 for further details 3. For specified FM deviation 4. Tx select low > full RF output 5. ±30kHz FM deviation 6. Min/max at ±50kHz offset 7. Max at ±50kHz offset 8. Average, at max. data rate Application Information Modulation formats and range extension The module will produce the specified FM deviation with a 2-level digital input to TXD which toggles between 0V and 3V. Reducing the amplitude of the data input from this value (usually as a result of reducing the supply voltage) reduces the transmitted FM deviation, typically to ±20-22kHz minimum at 2.7V. The receiver will cope with this quite happily and no significant degradation of link performance should be observed. TXD is normally driven directly by logic levels but will also accept analogue drive, e.g. 2-tone signalling. In this case it is recommended that TXD (pin 14) should be DC-biased to 1.5V with the modulation ACcoupled and limited to a maximum of 3V peak-to-peak. The instantaneous modulation voltage must not swing below 0V or above 3V at any time if waveform distortion and excessive FM deviation is to be avoided – use a resistive potential divider and/or level shifter to accomplish this if necessary. The varactor modulator in the transmitter introduces some 2nd harmonic distortion which may be reduced if necessary by predistortion of the analogue waveform. At the other end of the link the AF output (pin 13) can be used to drive an external decoder directly. Although the module baseband response extends down to DC, data formats containing a DC component are unsuitable and should not be used. This is because frequency errors and drifts between the transmitter and receiver occur in normal operation resulting in DC offset errors on the AF output. The time constant of the adaptive data slicer in the BiM3B is set at a reasonable compromise to allow the use of low code speeds where necessary whilst keeping settling times acceptably fast for batteryeconomised operation. RXD output on pin 12 is “true” sense, i.e. as originally fed to the transmitter. Radiometrix Ltd, BiM3B Data Sheet page 5 In applications such as longer range fixed links where data speed is not of primary importance, a significant increase in range can be obtained by using the slowest possible data rate together with filtering to reduce the receiver bandwidth to the minimum necessary. In these circumstances the AF output can be used to drive an external filter and data slicer. The AF output waveform on pin 13 is in the same sense as that originally fed to the transmitter, i.e. no inversion takes place. Received Signal Strength Indicator (RSSI) The BiM3B receiver incorporates a wide range RSSI which measures the strength of an incoming signal over a range of approximately 60dB. This allows assessment of link quality and available margin and is useful when performing range tests. Please note that the actual RSSI voltage at any given RF input level varies somewhat between units. The RSSI facility is intended as a relative indicator only - it is not designed to be, or suitable as, an accurate and repeatable measure of absolute signal level or transmitter-receiver distance. The output on pin 11 of the module has a standing DC bias in the region of 0.25V with no signal, rising to around 1.15V at maximum indication (RF input levels of -50dBm and above). For any given RF input level, absolute RSSI voltage is likely to vary somewhat between individual units - please refer to specifications table on p4. The RSSI output source impedance is high (~50kΩ) and external loading should therefore be kept to a minimum. Typical RSSI characteristic is shown below (this is for indicative purposes only and is not a guarantee of actual RSSI characteristics): Fig.4: Typical RSSI response curve To ensure a reasonably fast response the RSSI has limited internal decoupling of 1nF to ground. This may result in a small amount of audio ripple on the DC output at pin 11 of the module. If this is a problem further decoupling may be added at the expense of response speed, in the form of a capacitor from pin 11 to ground. For example, adding 10nF here will increase RSSI response time from 100µs to around 1ms. The value of this capacitor may be increased without limit. Radiometrix Ltd, BiM3B Data Sheet page 6 Expected range Predicting the range obtainable in any given situation is notoriously difficult since there are many factors involved. The main ones to consider are as follows: Type and location of antennas in use (see below) Type of terrain and degree of obstruction of the link path Sources of interference affecting the receiver “Dead” spots caused by signal reflections from nearby conductive objects Data rate and degree of filtering employed (see page 5) Assuming the maximum 64kb/s data rate and ¼-wave whip antennas on both transmitter (@ 5mW) and receiver, the following ranges may be used as a rough guide only: Cluttered/obstructed environment, e.g. inside a building Open, relatively unobstructed environment : : 50-75m 200-300m It must be stressed, however, that range could be much greater or much less than these figures. Range tests should always be performed before assuming that a particular range can be achieved in any given application. Antenna considerations and options The choice and positioning of transmitter and receiver antennas is of the utmost importance and is the single most significant factor in determining system range. The following notes are intended to assist the user in choosing the most effective arrangement for a given application. Nearby conducting objects such as a PCB or battery can cause detuning or screening of the antenna which severely reduces efficiency. Ideally the antenna should stick out from the top of the product and be entirely in the clear, however this is often not desirable for practical or ergonomic reasons and a compromise may need to be reached. If an internal antenna must be used, try to keep it away from other metal components and pay particular attention to the “hot” end (i.e. the far end), as this is generally the most susceptible to detuning. The space around the antenna is as important as the antenna itself. Microprocessors and microcontrollers tend to radiate significant amounts of radio frequency hash, which can cause desensitisation of the receiver if its antenna is in close proximity. 868MHz band is generally less prone to this effect than lower frequencies, but problems can still arise. Things become worse as logic speeds increase, because fast logic edges are capable of generating harmonics across the UHF range which are then radiated effectively by the PCB tracking. In extreme cases system range can be reduced by a factor of 3 or more. To minimise any adverse effects, situate the antenna and module as far as possible from any such circuitry and keep PCB track lengths to the minimum possible. A ground plane can be highly effective in cutting radiated interference and its use is strongly recommended. A simple test for interference is to monitor the receiver RSSI output voltage, which should be the same regardless of whether the microcontroller or other logic circuitry is running or in reset. Two types of antenna are recommended for use with the BiM3B: Whip (¼-wave). This consists simply of a piece of wire or rod connected to the module at one end. The lengths given below are from module pin to antenna tip including any interconnecting wire or tracking (but not including any 50Ω coax or microstrip connection). This antenna is simple, cheap, easy to set up and performs well. It is especially effective when used with a ground plane, which in practice is often provided by the main PCB or by a metal case. Base-loaded whip. In applications where space is at a premium a shortened whip may be used, tuned by means of a coil inserted at the base. This coil may be air-wound for maximum efficiency, or a small SMT inductor can be used. The value must be empirically chosen to tune the particular length of whip for best results “in situ”, making this antenna more difficult to set up. Radiated power will generally be slightly less than that obtained from a ¼-wave whip. Radiometrix Ltd, BiM3B Data Sheet page 7 L RF wire, rod, PCB track or a combination of these L (mm) = 71250 / freq(MHz) RF shortened wire, rod, PCB track etc. with loading coil. SMT inductor may be used if reqd. 1/4-wave whip Base-loaded whip Fig. 5: Antenna configurations Other types of antennas are feasible but tend to have drawbacks at these frequencies. Helical and tuned loop antennas are both very compact but tricky to set up, and can be impractical at 868MHz because of their very small size. Microstrip patch antennas are relatively large in area, directional, and have gain. Note: Where the specified antennas are mounted on the PCB and/or in close proximity to metalwork (module casing, components, PCB tracking etc), the antenna radiation pattern may be seriously affected. Radiated power may be significantly increased in some directions (sometimes by as much as 10dB) and correspondingly reduced in others. This may adversely affect system performance where good all-round coverage is desired. Care should also be taken to ensure that this effect does not increase the radiated power in any direction beyond that allowed by type approval regulations. Where this occurs the antenna may need to be relocated. In extreme cases a resistive attenuator of appropriate value may be required between the module and antenna. Radiometrix Ltd, BiM3B Data Sheet page 8 Type Approval requirements: Europe The modules comply with the requirements of the R&TTE Directive (including standards EN 300 220-3 and EN 301 489-3) when used in accordance with the information contained herein. The following provisos apply: 1) The modules must not be modified or used outside their specification limits. 2) The modules may only be used to transfer digital or digitised data. Analogue speech and/or music are not permitted. 3) The equipment in which the BiM3B is used must carry all necessary external labelling to meet the requirements of the R&TTE directive. 4) The BiM3B has not been tested with antennas having gains greater than that of a quarter-wave whip. The use of such antennas may require further R&TTE approval. Module mounting considerations Good RF layout practice should be observed. In particular, any ground return required by the antenna or feed should be connected directly to the RF GND pins at the antenna end of the module, and not to the OV pins which are intended as DC grounds only. All connecting tracks should be kept as short as possible to avoid any problems with stray RF pickup. If the connection between module and antenna does not form part of the antenna itself, it should be made using 50Ω microstrip line or coax or a combination of both. It is desirable (but not essential) to fill all unused PCB area around the module with ground plane. Variants and ordering information BiM3B modules are manufactured in the following variants as standard: For European applications in the 868 - 870MHz band: Part number BiM3B-869-64 BiM3B-869-10 RF power (typ.) 7dBm 7dBm Frequency 869.85MHz 869.85MHz Data rate 64kbps 10kbps BiM3B-868-64 BiM3B-868-10 14dBm 14dBm 868.30MHz 868.30MHz 64kbps 10kbps For carrier detect (CD) output variant add CD suffix to the above part numbers. e.g. BiM3B-869-64-CD Non-standard versions can be supplied to individual customer requirements, optimised for specific data speeds/formats. Minimum order quantities apply. Please consult the Sales department for further information. Radiometrix Ltd, BiM3B Data Sheet page 9 10 100 500 868.0 [mW] 600kHz 25mW <1% or LBT Duty Cycle 868.60 100kHz 868.70 10mW <1% 25kHz or WB No Spacing Channel Spacing Applications Alarm 500kHz <1% 25kHz 869.25 250kHz 500mW 869.65 869.70 50kHz 25mW <10% or LBT <10% 869.30 869.40 50kHz 50kHz 100kHz 869.20 No Spacing 25kHz 25kHz or Wide Band 300kHz 5mW 870.0 up to 100% Non-specific SRD Alarm Non-specific SRD 10mW 10mW 10mW <0.1% <0.1% or LBT 25mW 25kHz Social Alarm Alarm No Spacing Non-specific SRD CEPT/ERC Rec 70-03, 868 MHz Band Plan Non-specific SRD RF POWER [ERP] Radiometrix Ltd, BiM3B Data Sheet page 10 [MHz] Radiometrix Ltd Hartcran House 231 Kenton Lane Harrow, Middlesex HA3 8RP ENGLAND Tel: +44 (0) 20 8909 9595 Fax: +44 (0) 20 8909 2233 [email protected] www.radiometrix.com Copyright notice This product data sheet is the original work and copyrighted property of Radiometrix Ltd. Reproduction in whole or in part must give clear acknowledgement to the copyright owner. Limitation of liability The information furnished by Radiometrix Ltd is believed to be accurate and reliable. Radiometrix Ltd reserves the right to make changes or improvements in the design, specification or manufacture of its subassembly products without notice. Radiometrix Ltd does not assume any liability arising from the application or use of any product or circuit described herein, nor for any infringements of patents or other rights of third parties which may result from the use of its products. This data sheet neither states nor implies warranty of any kind, including fitness for any particular application. These radio devices may be subject to radio interference and may not function as intended if interference is present. We do NOT recommend their use for life critical applications. The Intrastat commodity code for all our modules is: 8542 6000 R&TTE Directive After 7 April 2001 the manufacturer can only place finished product on the market under the provisions of the R&TTE Directive. Equipment within the scope of the R&TTE Directive may demonstrate compliance to the essential requirements specified in Article 3 of the Directive, as appropriate to the particular equipment. Further details are available on The Office of Communications (Ofcom) web site: http://www.ofcom.org.uk/radiocomms/ifi/ Information Requests Ofcom Riverside House 2a Southwark Bridge Road London SE1 9HA Tel: +44 (0)845 456 3000 or 020 7981 3040 Fax: +44 (0)20 7783 4033 [email protected] European Radiocommunications Office (ERO) Peblingehus Nansensgade 19 DK 1366 Copenhagen Tel. +45 33896300 Fax +45 33896330 [email protected] www.ero.dk